Pro RANGE User Manual
Contents
1. OE READ ONLY ACCOUNT Enable Read Only Account od Read Only Username guest Password O CONFIGURATION MANAGEMENT Backup Configuration Backup System Log Upload Configuration Choose file No file chosen DEVICE MAINTENANCE Pro Range User Manual 1 3 Page 42 of 44 SILVERNET Firmware Upgrade Firmware Version Displays the current firmware Choose File Select the firmware file you wish to upgrade Upload Click upload to begin the update process Please be patient as the firmware upgrade routine can take 3 7 minutes The device will be un accessible until the firmware upgrade is completed Do not switch off the device Do not reboot and do not disconnect the device from the power supply during the firmware upgrade process as these actions will damage the device Host Name Host Name Enter a name for your device Administrative Account Administrator Username Enter an admin username Default is admin Current Password Enter your current password Default is password New Password Enter a new password Verify New Password Re enter your new password Read Only Account Enable Read Only Account Check to enable Read Only Username Enter a read only username Default is guest Password Enter a password No password is set by default Configuration Management Backup Configuration Click to save down the configuration file of the device Backup System Log Click to save down the system log of the device Upload Configuration2. The Pro Range supports the following wireless modes e Station e Station WDS e Access Point e Access Point WDS e Repeater e Repeater WDS e Wireless Adapter System Requirements e Windows XP Windows Vista Windows 7 Windows 8 Linux or Mac OS X e Web Browser Mozilla Firefox Apple Safari Google Chrome or Microsoft Internet Explorer 8 or above Pro Range User Manual 1 3 Page 4 of 44 SILVERNET Getting Started To access the Pro Range Configuration Interface perform the following steps 1 Configure the Ethernet adapter on your computer with a static IP address on the 192 168 0 x subnet for example IP address 192 168 0 100 and subnet mask 255 255 255 0 Internet Protocol Version 4 TCP TPv4 Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings 5 Obtain an IP address automatically Use the following IP address IP address 192 168 0 100 Subnet mask 255 255 255 0 Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server Validate settings upon exit 2 Launch your web browser and enter the default IP address of your device in the address field Press Enter PC or Return Mac Pro Range products 192 168 0 229 192 168 0 228 Google Windows Interne
3. Ping Interval seconds Startup Delay seconds Failure Count To Reboot AUTO REBOOT Auto Reboot Mode Apply Spanning Tree Protocol Multiple interconnected bridges create larger networks using IEEE 802 1d Spanning Tree Protocol STP which is used for finding the shortest path within a network and eliminating loops from the topology Enable STP Check to enable Spanning Tree Protocol Root Priority Enter the Root Priority The default priority for switches is 32768 Root hello time The hello time is the time between each bridge protocol data unit BPDU that is sent on a port This time is equal to 2 seconds sec by default but you can tune the time to be between 1 and 10 sec Root forward delay The forward delay is the time that is spent in the listening and learning state This time is equal to 15 sec by default but you can tune the time to be between 4 and 30 sec Root maximum age The max age timer controls the maximum length of time that passes before a bridge port saves its configuration BPDU information This time is 20 sec by default but you can tune the time to be between 6 and 40 sec Pro Range User Manual 1 3 Page 38 of 44 SILVERNET Ping Watchdog Ping watchdog allows you to set an IP address that the device must monitor If the device fails to get a response from the IP address Ping watchdog will reboot the device Enable Ping Watchdog Check this to enable ping watchdog IP address to Ping Specify the IP addr
4. Select the configuration file you wish to upload and click the restore button Device Maintenance Reboot This reboots the device Reset to defaults This will reset the device to the default factory settings IP address 192 168 168 1 Pro Range User Manual 1 3 Page 43 of 44 SILVERNET Contact Us SilverNet Ltd 2 Vermont Place Tongwell Milton Keynes MK15 8JA Online Resources If you need any further assistance go to our website download centre www silvernet com downloadcentre Read the easy as 1 2 3 setup guide http www silvernet com assets Easy as123 duide 1 pdf View our troubleshooting guide http www silvernet com supportfreguently asked guestions Use our online ticket support www silvernet com support Email us at support silvernet com Call our support team on 08712233067 www silvernet com Pro Range User Manual 1 3 Page 44 of 44
5. device interface Netmask Enter the class for the IP address The default is a class C value of 255 255 255 0 Gateway optional Enter the gateway IP address of the network the device is connected to DHCP Fallback IP Enter an IP address that the device should use if there is no DHCP server to give it an IP address DHCP Mode select none DHCP server or DHCP relay None DHCP function disabled DHCP Server Check to enable The device will act as a DHCP server hand out IP addresses automatically DHCP Relay Check to enable Enter the IP address of the remote DHCP server where the DHCP Client request will be relayed to DHCP Start IP Address Enter the starting IP address to be issued DHCP End IP Address Enter the last IP address the server will issue DHCP Lease Time Enter the new lease time in seconds DHCP Server Relay IP Enter the IP address of the remote DHCP server where the DHCP Client request will be relay to get the IP address DHCP Gateway Relay IP Enter the IP address of the remote gateway where the DHCP Client request will be relay to get the gateway IP address Enable DNS Proxy If enabled the router operation will act as proxy to resolve all DNS requests Pro Range User Manual 1 3 Page 25 of 44 SILVERNET DHCP Reservations DHCP SERVER RESERVATIONS IP Address Hardware MAC Description If you want a device to have a specified IP address then enter the details here Enter the IP address you want the device MAC address and a
6. to authenticate itself with radius server IEEE802 1x Key Rotation Enter time in seconds Time before activate key rotation in authentication process for higher security IEEE802 1x Key Length This is the key length of the initial seed key Select 64 or 128bit Pro Range User Manual 1 3 Page 19 of 44 SILVERNET Virtual Access Point VAP Virtual AP VAP implements mSSID Multi SSID whereby a single wireless card can be setup with up to 3 virtual SSID connections Each VAP can be set with different security authentication mode BASIC WIRELESS SETTINGS VAP ESSID Mimo Series VAP 0 Hide SSID WIRELESS SECURITY Security none Apply Settings All VAPs are created from the same radio and they all share the same wireless channel country code channel spectrum width and transmit power Once settings have been applied you will need to tick the enable button on the wireless page and apply settings Pro Range User Manual 1 3 Page 20 of 44 SILVERNET Advanced Wireless Tab The Advanced Wireless tab contains the long distance parameter settings and a few other advanced settings Only technically advanced users who have Sufficient Knowledge about WLAN technology should use the advanced wireless settings SILVERNET wireless advanced advanced Services wireless network LONG RANGE PARAMETERS Dutdoor Mode Beacon Interval RTS Threshold Fragmentation Threshold Distance Slot Time us ACK Timeout us CT
7. Chainmask Selection Available selections are e 1x1 Left Chain This will force the radio card to operate with 1 spatial stream on the left port of radio card only e 1x1 Right Chain This will force the radio card to operate with 1 spatial stream on the right port of radio card only e 2x2 Dual Chain This will enable the radio card to operate with 2 spatial streams on both of the radio card ports Multiple streams increase data transfer performance significantly Station Isolation When checked it prevents any wireless stations clients connected to the same AP from discovering each other Minimum Station RSSI When enabled if the signal strength of any device connected to the AP falls below the value in this box the AP will drop the connection Antenna Gain This should be set to match the antenna gain in dBi of the antenna you have connected to the wireless device For example if you have a BASE 95 with an Omni antenna set the gain to 12 because it is a 12dBi Omni antenna If you have a sector antenna then set the value as 16 because it is a 16 dBi antenna Pro Range User Manual 1 3 Page 23 of 44 SILVERNET Network Tab The Network tab allows you to configure the IP address of the device as well as any DHCP settings and bandwidth control settings NETWORK INFORMATION Network Mode Disable Network Interface MTU LOCAL AREA NETWORK LAN Mode IP Address Netmask Gateway IP DHCP Fallback IP DHCP Mode DHC
8. ETUD nomina sti DAE AE SE EE EE a 32 Remote Management Setup cooonncnccninnnnnnccinananananinananunncnonanacananionauna non ee ee 32 MN 32 VLAN Tab sissies Se ee ede eed Ee de De E ee Ee ds 33 VAN MOTO id O EE ED EE 33 MLAN EXAMDIOS secs EO ER EE ER EA 36 SErVICES Ro N EE AE EE RE NE n 38 Spanning tee Protocol EE EE a 38 PINO VV ICING Oe Ee LE ee ee ee de oe ales 39 AUTO REDOO EE ET NO N 39 SNMP CCU Does 40 Pro Range User Manual 1 3 Page 2 of 44 SILVERNET NTP Set ED Re id 41 Ma Eks RA EE EG 41 Teme SENSE EE DE Ee EE aoa 41 ON 41 O 41 O 42 Firmware Upgrade ui EN A A 43 POSE Malie ss tate eae rs 43 Administrative ACCOUNT naa N a 43 Read ONV ACCOUN ee ee LA oe E AN 43 Configuration Management usina 43 Device MINEN CE GE A 43 Contact Use se A De ee a 44 CONGRESO UEC os EO cass RR SE ER RE EE cates EE EES ER re oe 44 Pro Range User Manual 1 3 Page 3 of 44 SILVERNET Introduction This User Guide describes the firmware version 2 30 1 which is integrated into all Pro Range 95 and 240 products provided by SilverNet Ltd Supported Products This manual covers all Pro 95 and Pro 240 products listed below e MICRO 95 e LITE 95 e MAX 95 e BASE 95 e LITE 240 e MAX 240 e BASE 240 e ACCESS 240 For more information visit www silvernet com Pro Range Network Modes The SilverNet Pro Range supports the following network modes e Transparent Bridge mode layer 2 e Router Mode Pro Range Wireless Modes
9. ID number select Tag and click add Untagged VLAN to add an untagged VLAN to the Ethernet port type in the ID number select Untag and click add Radio VLAN Tagged VLAN to add a tagged VLAN to the MAIN wireless SSID type in the ID number select Tag and click add Untagged VLAN to add an untagged VLAN to the MAIN wireless SSID type in the ID number select Untag and click add You can also set up any VLANS for any Virtual Access Points you may have created Pro Range User Manual 1 3 Page 34 of 44 SILVERNET VLAN Management Enables you to control who can access the device by allowing only those on the same Tag VLAN ID to access the web page VLAN MODES No Wlan Wan Switch IEEE802 1p Compatible a Vlan Management IEEE802 1p Compatible Qing IEEE802 1p Compatible VLAN MANAGEMENT VLAN ID IP ADDRESS NETMASK GATEWAY Po N mee MANAGEMENT IP VLAN ID IP ADDRESS NETMASK GATEWAY If you add a VLAN ID of 2001 and IP address of 192 168 0 20 then only computers on the same VLAN ID 2001 can open the web page using IP address 192 168 0 20 QinQ Can be used to achieve simple layer two VPN connectivity between sites by encapsulating one 802 1Q trunk inside another Only use this if you are a very advanced user and have good knowledge of QinQ VLAN MODES No Vlan Vlan Switch IEEE802 1p Compatible Vlan Management IEEE802 1p Compatible QinQ IEEE802 1p Compatible ETHERNET 1 QINQ Port Acting As Customer Network Port C
10. N Y Attached to witch S VLAN Tag v ETHERNET 2 QINQ Port Acting As Attached to witch S VLAN Tag 7 RADIO 1 QINQ Port Acting As Attached to witch S VLAN Tag Y RADIO 2 QINQ Port Acting As Customer Network Port CN Y Attached to witch S VLAN Tag y Provider Network Port PN Enter the VLAN ID of the Ethernet port or radio port and click add You can also set the priority Customer Network port CN Select which VLAN tag to attach it to by selecting from the Dropbox Pro Range User Manual 1 3 Page 35 of 44 SILVERNET VLAN Examples Tagged wireless VLAN to Tagged Ethernet VLAN setups Tag vlan connection Setup Setup 1 ssid1 tag vlan ID 100 tag vlan ID 100 tag vian ID 200 VLAN switch S E i Ethernet port 1 tag vlan ID 100 WPC1 wlan tag vian ID 100 tag vian 190 port 2 tag vlan ID 100 PC2 ethernet tag vlan ID 100 Setup 2 ssid1 tag vlan ID 100 tag vlan ID 200 Ethernet tag vlan ID 100 tag vlan ID 200 VLAN switch gt WPC1 wlan tag vlan ID 200 port 1 tag vlan ID 100 Lport 2 tag vlan ID 200 PC2 ethernet tag vlan ID 200 Setup 3 ssid1 tag vlan ia n tag vlan ID 100 A A VLAN switch STN AP VLAN switch a L port 1 tag vlan ID 100 Ethernet Ethernet port 1 tag vian ID 100 dd port 2 tag vlan ID 100 tag vian ID 100 tag vlan ID 100 port2 tag vlan ID 100 PC1 ethernet PC2 ethernet tag vlan ID 100 tag vlan ID 100 If you add a Tag VLAN to Etherne
11. P Start IP Address DHCP End IP Address DHCP Netmask DHCP Gateway IP DHCP Lease Time DHCP Relay Server IP DHCP Relay Gateway IP Enable DNS Proxy Pro Range User Manual 1 3 NONE DHCP Client es Static 192 165 0 229 259 299 299 0 192 168 168 102 NONE es DHCP Server DHCP Relay 192 166 0 50 192 168 0 200 259 209 299 0 seconds 192 168 168 254 192 168 168 1 LJ Page 24 of 44 SILVERNET Network Information Network Mode Select between Bridge mode default and Router mode Bridge mode is what you need to use for a point to point link Disable Network You can disable the LAN so that only the wireless part of the device is working You will only be able to access the device via another wireless device that is connected to it Interface MTU By default any Ethernet interface has its maximum transmission unit MTU size set to 1500 bytes which is the maximum and expected value for Ethernet frames If packets larger than 1500 bytes are expected on your network you can increase the MTU size Local Area Network LAN Mode Static Here you can enable DHCP Client or Static default DHCP Client If enabled your device will get an IP address automatically from the network There must be a DHCP server on your network for this to work Static Allows you to enter a static IP address IP address Enter the IP address you wish to give to the device You will use this IP address to access the
12. Page 29 of 44 SILVERNET Static Routing Table You can manually add static routing rules to the system routing table you can set a rule that a specific target IP address or range of IP addresses passes through a specific gateway STATIC ROUTING Destination IP Network Mask Gateway od Lood GE STATIC ROUTING TABLE Destination IP Network Mask Gateway Destination IP Specify the IP address of the destination Netmask Specify the Netmask of the destination Gateway IP Specify the IP address of the gateway Routing Information Protocol RIP Setup RIPvi1 is a classful routing protocol and it does not support VLSM Variable Length Subnet Masking RIPvi does not support authentication RIPv2 is classless routing and it supports VLSM Variable Length Subnet Masking RIPv2 supports authentication Routing Info Protocol Check to enable RIP Routing Info Protocol version Select from RIPvi and RIPv2 Pro Range User Manual 1 3 Page 30 of 44 SILVERNET Firewall Setup PA Ad PY ARM FP Firewall On Comment Policy IP Type Source IP Mask Src Port Destination IP Mask Des Port C i ace vce eT oO O eT po Jaccer wfre ET po Jaccee ree DE po Jaceer vfree IE II po Jaccer wfre gt JP po Jaccee ree eT po Jaccer vfree IE FI y po Jaccee vce gt JP po Jaccee ree eT oO Maeeer vce IE II po Jaccer vce gt JP po Jaccee ree JP oo Jaceee vlree eT po Jaccer vce gt JP po Jacc
13. S Timeout us OTHER SETTINGS Noise Immunity jw Enable meters W Auto Adjust for Slottime ACK Timeout CTS Timeout Enable Signal Strength Indicator RSSI 75 100 Radio Off with No Ethernet Chainmask Selection Station Isolation Minimum Station RSSI Antenna Gain Enable Enable W Enable Apply Settings To apply any settings to the radio click Apply Settings Once you have done this it will ask you to either Save or Discard any changes To immediately save your changes click Save To cancel your changes click Discard Pro Range User Manual 1 3 Page 21 of 44 SILVERNET Long Range Parameters Outdoor Mode Check to enable outdoor mode Beacon Interval This value indicates the freguency interval of the beacon A beacon is a packet broadcast by the router which carries the SSID channel number and security protocols We recommend using the default setting of 100 In poor reception areas you may turn this down to 50 RTS Threshold This value is set to 2346 as default We recommend leaving this setting The device sends Request to Send RTS frames to a particular receiving station and negotiates the sending of a data frame After receiving an RTS the wireless station responds with a Clear to Send CTS frame to acknowledge the right to begin transmission Fragmentation Threshold This is set to 2346 as default We recommend leaving this setting This specifies the maximum size for a packe
14. SILVERNET Pro RANGE User Manual Version 1 3 24 07 2014 SILVERNET Table of Contents MVM MCS ele oras EO ER 4 Getung St Eed ER EE Sera roa RLV ION TS EP Tn SOTO ATONE 5 Navidad cirio 6 status A EG EE EE N IE RE RE GR Ee Ee oe 7 El EE EL OE AE OE OE RE OO NE OD EE 7 VESIO NN vara devas 8 EANWAN SS CUE CS Ee Ie GE De ohne ieee eee 8 Bale AE AE OE EO OE OE ET N TO OE EE OE OE IE 9 MO Ese vs El ORR OE N OE specu ME AL EO KP 10 Wireless Tab ES ee li 11 Da SiG WV If LESS Second Sustancia 12 Wireless SCC V is EE ets cs Sari SE Baad erase Snes Ee ride eee RE GE SEE 15 WER ie ES OE AAA ca N A aaa oan ee E 16 WPAANPA2 AUED ENE EREIO 6 ete ic alee 17 WPA WPAZ Wit EAP cta dt a 18 Virtual ACCESS BOMEVAP ns EE poso rs seo isc 20 Advanced Wireless Tab sinusitis 21 bog Rare Parameters EE EE ee EE ie selands 22 Desi aa e ss EE EE EE iene eee eee 22 NetWork tab SE EE co nee ae ee 24 Netwotk infOEFatOFR EE GEE EN GENE EE EG N GE 25 EOC all Areda INCE WOR ssa EE a e e dle os 23 DIEP RESCEV CIOS DE A RE SG 26 Domain Name Server AddresseS ees ees ee ee ee ee ee ee ee ee 26 DaridwidtEontrOl ai rer ey OG GO EE EE GO EG Ee eee 21 o a HE On SUN eae Pe 27 Advanced Network Tab ED N DS ed N De ee ek ee Ee es 28 Nat Se AE EA RD Ge Re ER OR NEE Ge Ee DE 29 Statie ROULING ONC eN GE N bole Ee ER EG ee ED Ge oe 30 Routing Information Protocol RIP Setup eee ee ee ee ee 30 Firewall SetuP DER SE da anal 31 M lticast ROULING S
15. TP Port E UPNP SETUP UPnP Enabled Pro Range User Manual 1 3 Page 28 of 44 SILVERNET Nat Setup NAT Network Address Translation NAT enables packets to be sent from the external network WAN to the local interface IP address and then sub routed to other client devices on its local network while the PRO 95 device is operating in Access Point or AP Repeater mode Packets are routed in the reverse direction in Station mode DMZ DMZ Demilitarized Zone specifically allows one computer device behind NAT to become demilitarized so all ports from the public network are forwarded to the ports of this private network similar to a 1 1 NAT DMZ Private IP Specify the IP address of the local host network device The DMZ host device will be completely exposed to the external network Port forwarding This allows specific ports on the local network to be forwarded to the external network WAN This is useful for a number of applications such as FTP servers VoIP gaming that require different host systems to be seen using a single common IP address port ADD PORT FORWARD ENTRY Known Server Server Type Private IP Address Public IP From A 2 YAA Custom Server Server Type Private IP Address Port Forwarding Table Server Type Add Protocol Public Port From To Private Port From Public IP From KO PA 7 Add Protocol Public Port Private IP Private Port Public IF Apply Setting Pro Range User Manual 1 3
16. ackets received Received Errors Displays the number of receive errors Transmitted Bytes Displays the total amount of data in bytes transmitted during the connection Transmitted Packets Displays the total amount of packets transmitted Transmitted Errors Displays the number of transmit errors Local AP Station errors Rx invalid NWID Displays the number of packets received with a different NWID or ESSID packets which were destined for another access point Rx Invalid Crypt Displays the number of transmitted and received packets which were encrypted with the wrong encryption key and failed the decryption routines It can be used to detect invalid wireless security settings Rx Invalid Frag Displays the number of packets missed during transmission and reception Tx Excessive Retries Displays the number of packets which failed to be delivered to the destination Undelivered packet are retransmitted a number of times before an error occurs Missed beacons Displays the number beacons management packets sent at regular intervals by the Access Point which were missed by the client This can indicate that the wireless client is out of range Other errors Displays the total number of transmitted and received packets that were lost or discarded for other reasons More Status The More Status drop down box contains some useful tools and additional status pages These are e Ping Utility a ping tool to test the connectivity betw
17. ce The Pro Range supports seven operating modes e Station e Station WDS e Access Point e Access Point WDS e Repeater e Repeater WDS e Wireless Adapter Station If you have a client device to connect to an AP configure the client device as Station mode The SSID of the AP is used and it forwards all the traffic to from the network devices to the Ethernet interface This mode translates all the packets that pass through to its own MAC address thus resulting in a lack of transparency Station WDS This mode is used to create a transparent bridge and can be connected to a device running in Access Point WDS mode Access Point If you have a single device to act as an AP configure it as Access Point mode The device functions as an AP that connects multiple client devices Access Point WDS This mode connects to a device running Station WDS mode It is used to create a transparent bridge In most cases we recommend that you use WDS because it enables transparent Layer 2 traffic The WDS protocol is not defined as a standard so there may be compatibility issues between equipment from different vendors Repeater Mode In this mode the device acts as a relay for network signals on the network by regenerating the signals it receives and retransmitting them to the main network infrastructure Repeater WDS Mode Repeater WDS Mode is used mainly to extend the wireless range and coverage of the wireless network allowing access and communicatio
18. channel scan list can be modified using the Channel Scan List control Remote AP Lock to MAC This option will make the device only connect to this access point This is important when connection is Point to Point operation as the Station will not look for other Access Points to associate with Remote AP Preferred MAC Enter the preferred MAC address of the access point you want device to connect when it first starts up Up to max of 4 MAC addresses can be entered Priority is from top to bottom In the event that all preferred MAC addresses are not available the device will then pick the matching SSID access point with the strongest signal Country Code Each country has their own power level and frequency regulations To ensure the device operates under the necessary regulatory compliance rules you must select the country where your device will be used The IEEE 802 11 mode channel and frequency settings and output power limits will be tuned according to the regulations of the selected country Channel Width Displays the spectral width of the radio channel You can use this option to control the bandwidth consumed by your link Using higher bandwidth increases throughput Using lower bandwidth reduces throughput Channel widths available are 5 MHz 10 MHz 20 MHz 20 40 MHz Guard Interval This is the Guard band between packets For long distant connections select Long to give better performance Channel Frequency The default Auto all
19. e Server Enter your preferred time server Default is time nist gov WEB Server Web Server Mode By default HTTP service is enabled You can set to HTTPS HTTPS Port If HTTP mode is used specify the TCP IP port of the web server The default is 80 If secure HTTPS mode is used specify the TCP IP port of the web server The default is 443 Telnet Server Enable Telnet Server Check to enable Server Port Specify the TCP IP port of the Telnet server SSH Server Enable SSH Server Check to enable Server Port Specify the TCP IP port of the SSH server System log Enable System Log Check to enable Logging IP Domain name Enter the IP address or domain name of the host that receives syslog messages Properly configure the remote host to receive syslog protocol messages Logging Port The TCP IP port that receives syslog messages 514 is the default port for the commonly used system message logging utilities Pro Range User Manual 1 3 Page 41 of 44 SILVERNET Admin Tab The Admin tab contains administrative options This page enables the administrator to reboot the device reset it to factory defaults upload new firmware back up or upload the configuration and configure the administrator account FIRMWARE UPGRADE Firmware Version 2 31 0 231213 Choose file No file chosen HOST NAME Host Name lin MICRO ADMINISTRATIVE ACCOUNT Administrator Username Current Password O New Password O Verify New Password
20. e the last reboot or software upgrade The time is displayed in days hours minutes and seconds Host Name Displays the customizable name or identifier of the device The host name is also displayed in SilverView System Time Displays the current system date and time The date and time are displayed in DAY MONTH YEAR HOURS MINUTES SECONDS format The system date and time is retrieved from the Internet using NTP Network Time Protocol The NTP Client is disabled by default on the Services tab The device doesn t have an internal clock and the date and time may be inaccurate if the NTP Client is disabled or the device isn t connected to the Internet Pro Range User Manual 1 3 Page 7 of 44 SILVERNET Version Firmware Version Displays the SilverNet unit s software version Loader Version Displays the SilverNet unit s boot loader version LAN WAN settings LAN MAC Displays the MAC address of the device as seen on the LAN WAN MAC Displays the MAC address of the device as seen on the WAN Mode Displays the network operating mode IP address Displays the current IP address of the unit Gateway Address Displays the gateway address assigned by an external DHCP server connected to the WAN interface Primary DNS Secondary DNS IP The Domain Name System DNS is an Internet phone book that translates domain names to IP addresses These fields identify the server LAN cable Indicates the current status of the LAN Ethernet port conn
21. ection This can indicate that a cable is not plugged into a device or there is no active Ethernet connection Radio Wireless Mode Station WDS MAC 50 11 eb 00 0c f4 REMOTE AP SSID REMOTE AP MAC 50 11 E8 00 0C F7 Signal Strength Noise level TX Rate RX Rate TX CCQ Channel Width Frequency Security Ack Timeout LOCAL STATION STATISTICS Bytes Packets Errors Received o Transmitted LOCAL STATION ERRORS RX Invalid NWID 266 TX Excessive Retries RX Invalid Crypt Missed Beacons RX Invalid Frag Other Errors Pro Range User Manual 1 3 Page 8 of 44 SILVERNET Radio Wireless Mode Displays the operating mode of the radio interface The Pro Range Supports seven operating modes e Station e Station WDS e Access Point e Access Point WDS e Repeater e Repeater WDS e Wireless Adapter Local Remote AP SSID In Access Point WDS mode this displays the SSID of the device In Station WDS mode this displays the SSID of the AP the device is associated with Frequency Displays the operating frequency of the device Ack Timeout The ACK timeout specifies how long the device should wait for an acknowledgement from another device confirming it has received a packet before it concludes that there has been an error and resends the packet Changing the distance value will change the ACK Acknowledgement timeout accordingly Signal Strength Available in Station WDS mode only Displays the received wireless si
22. ee ree DE po Maeeer vce eT po Jaccer wfre gt JP po Jaccee ree JP po Jacceee vfree peo JP Fr Comment Enter a brief name for the service Policy Select Accept or Deny for the apply rule IP Type Select ICMP TCP or UDP Source IP Mask enter the source IP address and Netmask This is the source IP of the packet specified within the packet header usually it is the IP of the host system which sends the packets Src Port Enter the source port number This is the source port of the TCP UDP packet specified within the packet header usually it is the port of the host system application which sends the packets Destination IP Mask Enter the destination IP and Netmask is the Destination IP of the packet specified within the packet header usually it is the IP of the system which the packet is addressed to Des Port Enter the destination port This is the destination port of the TCP UDP packet specified within the packet header usually it is the port of the host system application which the packet is addressed to Pro Range User Manual 1 3 Page 31 of 44 SILVERNET Multicast Routing Setup Multicast Routing Enables multicast packet pass through between local and external networks while the device is operating in Router mode Multicast intercommunication is based on Internet Group Management Protocol IGMP Remote Management Setup Remote HTTP HTTPS Check box to enable Remote HTTP port Set the port to use for remo
23. een devices e ARP Table display a list of MAC addresses of the connected devices e Bridge Table display a list the devices connect to the bridge interface e DHCP Active Lease Table display a list of IPS addresses leased to all computers Pro Range User Manual 1 3 Page 10 of 44 SILVERNET Wireless Tab The Wireless tab contains everything needed to set up the wireless part of the link This includes SSID channel and freguency settings device mode data rates and wireless security SILVERNET wireless advanced advanced Services wireless network Apply Settings Enable Radio BASIC WIRELESS SETTINGS Wireless Mode Access Point WDS Local AP ESSID silvernetwireless L Hide SSID Country Code United States of America Id No Country Set Wireless Profile Long range parameter enabled Channel Spectrum Width Guard Interval Channel Frequency wf Auto Select A Data Rate Mbps W Auto Transmit Power 29 Y dBm Chainmask 2x2 Dual Aggregate Dual Chain Power W Maximum O Obey Regulatory Power Rate Aggressiveness Apply Settings To apply any settings to the radio click Apply Settings Once you have done this it will ask you to either Save or Discard any changes To immediately save your changes click Save To cancel your changes click Discard Pro Range User Manual 1 3 Page 11 of 44 SILVERNET Basic Wireless Settings Wireless Mode Displays the operating mode of the radio interfa
24. ess of the target host to be monitored by Ping Watchdog Ping interval Specify the time interval in seconds between the ICMP echo requests that are sent by Ping Watchdog The default value is 5 seconds We recommend setting this to 10 seconds Startup Delay Specify the initial time delay in seconds until the first ICMP echo requests are sent by Ping Watchdog The default value is 60 seconds The Start up Delay value should be at least 60 seconds as the network interface and wireless connection initialization takes a considerable amount of time if the device is rebooted Failure count to reboot Specify the number of ICMP echo response replies If the specified number of ICMP echo response packets is not received continuously Ping Watchdog will reboot the device The default value is 5 We recommend 10 seconds Auto Reboot Auto reboot mode You can set to auto reboot the unit every X hours or at a certain time of the day Pro Range User Manual 1 3 Page 39 of 44 SILVERNET SNMP SETUP Enable SNMP ff Read Password Write Password Engine ID 800007e5BD00002704C Enable SNMP Trap Trap Destination IP Community NTP SETUP Select Your Time Zone GMT 07 00 Mountain Time US Canada Current Router Time 12 31 1999 19 17 39 GMT O7 00 Proposed Router Time 07 29 2014 04 05 14 Enable NTP Client Known Time Server bonehed lcs mit edu T Time Server WEB SERVER Web server mode HTTPS Port SNMP Setup S
25. etween the 2 interfaces The default is 0 Router Mode In Router Mode the device also operates as a router Either the wireless or Ethernet can be setup as a WAN connection to a broadband modem The Device supports several types of broadband connections such as Static IP Dynamic IP and PPPoE For setup details refer to the respective section Static IP Address Use Static IP Address if you have been given a fixed IP from your ISP Dynamic IP Address With Dynamic IP Address the device automatically requests an IP address from the modem or ISP PPP over Ethernet PPPoE choose this option to obtain an IP address Gateway IP and DNS address dynamically from the external PPPoE server Pro Range User Manual 1 3 Page 27 of 44 SILVERNET Advanced Network Tab The advanced network tab allows you to configure Router settings including NAT setup and firewall setups This tab will not open when in device is in Bridge mode To open the page you must first enable Router mode on the Network page NAT SETUP NAT Enabled DMZ Enabled Port Forwarding T Enabled IP Forwarding T Enabled STATIC ROUTING TABLE Static Routing Table Enabled ROUTING INFORMATION PROTOCOL RIP SETUP Routing Info Protocol Enabled Routing Info Protocol Version RIPwi FIREWALL SETUP Firewall Enabled MULTICAST ROUTING SETUP Multicast routing W Enabled REMOTE MANAGEMENT SETUP Remote HTTP HTTPS Enabled Remote HT
26. gnal level Use the align button and adjust the device antenna to get a better link 35 to 45 dBm is recommended for stable links TX Rate Available in Station WDS mode only Displays the devices current data transmission TX rates or radio speed Transmit CCQ This index evaluates the wireless Client Connection Quality CCQ The level is based on a percentage value for which 100 corresponds to a perfect link state MAC This displays the MAC address of the device Local Remote AP MAC In Access Point WDS mode this displays the MAC address of the device In Station WDS mode this displays the MAC address of the AP the device is connected to Security Displays the wireless security method being used on the device If None is displayed then wireless security has been disabled Noise Level Displays the noise level in dBm RX Rate Available in Station WDS mode only Displays the devices current data reception RX rate Channel Width Displays the spectral width of the radio channel You can use this option to control the bandwidth consumed by your link Using higher bandwidth increases throughput Using lower bandwidth reduces throughput Channel widths available are 5 MHz 10 MHz 20 MHz 20 40 MHz Pro Range User Manual 1 3 Page 9 of 44 SILVERNET Local AP Station Statistics Received Bytes Displays the total amount of data in bytes received during the connection Received Packets Displays the total amount of p
27. hared Key This option is available when WPA or WPA2 with PSK is selected The pre shared key is an alpha numeric password between 8 and 63 characters long Pro Range User Manual 1 3 Page 17 of 44 SILVERNET WPA WPA2 with EAP Security CPA WPA Authentication EAP Cipher Type AUTO WPA Preshared Key eae eee Pri Radius Server IP 0 0 0 0 Sec Radius Server IP 0 0 0 0 Authentication Port 1812 Accounting Part fisia Radius Secret key private t MAC ACL Enabled EE Policy Allow E Primary Radius Server IP Enter the Primary Radius Server IP address Secondary Radius Server IP Enter the Secondary Radius Server IP address Authentication Port Enter the Authentication Port number of the Radius Server Default is 1812 Accounting Port Enter the Accounting Port number of the Radius Server Default is 1813 Radius Secret Key Enter the Secret Key of the Radius Server The device uses this key to authenticate itself with Radius Server MAC ACL The MAC address Access Control List ACL lets you allow or deny clients connectivity to the device When enabled you have the following options Select a Policy e Allow Wireless clients on the list can access the device Any wireless client that is not on the list is denied access to the device e Deny Wireless clients on the list are denied access to the device Any wireless client that is not on the list can access the device In Station mode you will have the foll
28. imple Network Monitor Protocol SNMP is an application layer protocol that facilitates the exchange of management information between network devices Enable SNMP Check to enable SNMP Read Password Enter the password for read only accounts Write password Enter the password for administrator accounts These are able to read and write Engine ID The engine ID is used with a hashing function to generate keys for authentication and encryption of SNMP v3 messages If you do not specify an engine ID one is generated when you enable the standalone SNMP agent Enable SNMP Trap Check to enable SNMP Trap Trap Destination IP Enter the IP address to send the information when the trap is triggered Community Specify the SNMP community string It is required to authenticate access to Management Information Base MIB objects and functions as an embedded password The default SNMP Community is public Pro Range User Manual 1 3 Page 40 of 44 SILVERNET NTP Setup Network Time Protocol NTP is a protocol for synchronizing the clocks of computer systems over packet switched variable latency data networks You can use it to set the system time on the device Select Your time Zone Select the correct time zone from the drop down menu Current Router Time The current time on the router Proposed Router Time The proposed time on the router Enable NTP Client Check to enable NTP Known Time Server You can select a time server from the drop down list Tim
29. mit Power The maximum transmit power displayed is determined by the country code and the maximum transmit power of the radio Rate Aggressiveness There are 2 scenarios where the Rate Aggressiveness is useful 1 When the Environment might be noisy Interference 2 When environment is free of interference For Scenario 1 you can select from 1 2 or 3 This will lower the throughput but increase the power For scenario 2 you can select from 1 2 3 This will increase the transmit rate and may improve throughput Channel Scan List This restricts scanning to only the selected frequencies The benefits are faster scanning as well as filtering out unwanted APs in the results The Site Survey tool will look for APs in selected frequencies only Pro Range User Manual 1 3 Page 14 of 44 SILVERNET Wireless Security All the wireless security settings are set under this section The operation of the Keys is the same for ALL the Wireless modes Security The Pro 95 range supports the following wireless security methods None If you want an open network without wireless security select none You still have the option of using RADIUS MAC authentication and MAC ACL WEP WEP Wired Equivalent Privacy is the oldest and least secure security algorithm Use WPA or WPA2 security methods when possible WPA WPA Wi Fi Protected Access was developed as a stronger encryption method than WEP WPA TKIP WPA Wi Fi Protected Access security mode wi
30. mpatible with all Access Points Not recommended Key Type HEX or ASCII option specifies the character format for the WEP key if WEP security method is used Current Key Specify the Index of the WEP Key used 4 different WEP keys can be configured at the same time but only one is used WEP Key WEP encryption key for the wireless traffic encryption and decryption should be specified if WEP security method is used WEP Key Length 64 bit selected by default or 128 bit WEP Key length should be selected if WEP security method is used The 128 bit option will provide a higher level of security Pro Range User Manual 1 3 Page 16 of 44 SILVERNET WPA WPA2 Authentication The configuration options are the same for all of the WPA and WPA2 options WPA2 AES is the strongest security method If all of the wireless devices on your network support this option we recommend that you select it REMOTE AP WIRELESS SECURITY Security WP AZ Em WPA Authentication Cipher Type Preshared Key ATT Identity anonymous User Name user example com User Password eeseesee WPA Authentication Specify one of the following WPA key selection methods e PSK Pre shared Key method selected by default e EAP EAP Extensible Authentication Protocol Cipher Type Specify which of the following to use e TKIP Temporal Key Integrity Protocol which uses RC4 encryption algorithm e AES Advanced Encryption Standard AES algorithm default Pre s
31. ns over places generally difficult for wireless clients to connect to the network Repeater WDS requires the access point to be setup in Access Point WDS mode to work The Repeater WDS must first link up with an Access Point WDS and then it can link up with a Station WDS It acts as an extension to the link and you can add more Repeaters as necessary Pro Range User Manual 1 3 Page 12 of 44 SILVERNET Local AP ESSID If the device is operating in Access Point or Access point WDS mode specify the wireless network name or SSID Service Set Identifier used to identify your WLAN All the client devices within range will receive broadcast messages from the AP advertising this SSID If the device is operating in Station mode specify the SSID of the AP the device is to connect to Hide SSID Once checked this will disable advertising the SSID of the access point in broadcast messages to wireless stations This option is only available in Access Point Access Point WDS and Repeater WDS mode Site Survey This is only available in Station Station WDS mode Site Survey will search for the available wireless networks in range on all the supported channels and will allow you to select one for association If the selected network uses encryption you ll need to set up the security parameters in the wireless security section Click Scan to re scan for the Access Points in range Select the Access Point from the list and click close this window Site Survey
32. owing options for EAP REMOTE AP WIRELESS SECURITY Security WP ae WPA Authentication Cipher Type Preshared Key ATT Identity anonymous User Name user example com User Password leessesee Identity Identification credential used by the WPA supplicant for EAP authentication User Name Identification credential used by the WPA supplicant for EAP tunnelled authentication in unencrypted form User Password Password credential used by the WPA supplicant for EAP authentication Pro Range User Manual 1 3 Page 18 of 44 SILVERNET IEEE802 1x Settings The operation of the Keys is the same for ALL the modes Note Operating with IEEE802 1x security will limit AP to maximum wireless link speed of 54Mbps only LOCAL AP WIRELESS SECURITY Security IEEEBO2 1X T Pri Radius Server IP Sec Radius Server IP Authentication Port Accounting Port Radius Secret Key IEEE802 1X Key Rotation IEEE802 1X Key Length MAC ACL a Remove Policy Primary Radius Server IP Enter the Primary Radius Server IP that Access Point will use to query server Secondary Radius Server IP Enter the Secondary Radius Server IP that Access Point will use to query the server Authentication Port Enter the Radius Server Authentication Port number to use Default is 1812 Accounting Port Enter Radius server Accounting Port to use Default is 1813 Radius Secret Key Enter Radius server Secret Key that Access Point to use
33. ows the device to automatically select the frequency You can specify a frequency from the drop down list The frequency range available depends on the country you select in Country Code Some countries have DFS regulations which may affect and delay the device when attempting to establish a connection It can take up to 15 minutes to connect Pro Range User Manual 1 3 Page 13 of 44 SILVERNET SILVERNET wireless advanced advanced Services wireless network Enable Radio BASIC WIRELESS SETTINGS Wireless Mode Remote AP ESSID silvernetwireless Remote AP Lock to MAC Y Enabled O Of Remote AP Preferred MAC OE O O E Country Code United States of America No Country set Wireless Profile Long range parameter enabled Channel Spectrum Width Guard Interval Data Rate Mbps 6 Mbps Auto Transmit Power dBm Chainmask 2x2 Dual Aggregate Dual Chain Power wf Maximum Obey Regulatory Power Rate Aggressiveness o Channel Scan List Enabled Data Rate Data Rates consist of both the legacy rates and the MCS Modulation Coding Scheme Only for 802 11n rates e 6 54Mbps are Legacy Rates e MCSO to MCS7 are 802 11n rates which uses only 1 stream e MCS8 to MCS15 are 802 11n rates which uses 2 streams When left on auto the data rate will follow an advanced rate algorithm that takes into account the amount of errors at that data rate and fine tunes to the best data rate it can use Trans
34. s NAT setup port forwarding and firewall setup e VLAN The VLAN Tab configures the VLANs settings for both the Ethernet and the radio e Services The Services Tab configures system management services Ping Watchdog Simple Network Management Protocol SNMP servers web SSH Telnet Network Time Protocol NTP client Spanning Tree Protocol STP and system log e Admin The Admin Tab controls administrator accounts management firmware update and configuration backup Pro Range User Manual 1 3 Page 6 of 44 SILVERNET Status Tab The Status tab displays a summary of the link status information current values of the basic configuration settings depending on the operating mode network settings and information and traffic statistics SILVERNET wireless advanced advanced services wireless network More Status T MAIN VERSION Uptime 0 Days 04 26 49 FIRMWARE VERSION 2 31 0 231213 Host Name LOADER VERSION System Time 12 31 1999 20 26 50 LAN SETTING WAN SETTING LAN MAC 50 11 eb 00 0c f6 WAN MAC MODE MODE IP ADDRESS 192 168 0 229 IP ADDRESS GATEWAY IP ADDRESS GATEWAY IP ADDRESS Pri DNS IP A Pri DNS IP Sec DNS IP OE Sec DNS IP LAN cable Wireless Mode Access Point WDS MAC 50 11 eb 00 0c f7 LOCAL AP SSID silvernetwireless LOCAL AP MAC 50 11 eb 00 0c f7 Frequency Security Ack Timeout Main Uptime This is the total time the device has been running sinc
35. small description Click add once you are done DHCP reservation is a process in which a particular IP address is mapped with one computer that is typically a server that needs to have a same IP address permanently When this is done every time the target DHCP client computer requests an IP address from the DHCP server the mapped IP address is assigned to it Since the IP address is reserved for a particular computer while specifying DHCP reservation it is not assigned to any other computer even if it is the only address available in the DHCP address pool Domain Name Server Addresses DOMAIN NAME SERVER ADDRESSES Obtain DNS server address automatically Use the following DNS server addresses Primary DNS IP Secondary DNS IP If you have specific DNS servers you like to use you can type them in here If you want the device to obtain DNS server addresses automatically the please check the relevant option Primary DNS IP Enter the primary DNS IP address Secondary DNS IP Enter the secondary DNS IP address Pro Range User Manual 1 3 Page 26 of 44 SILVERNET Bandwidth Control BANDWIDTH CONTROL Bandwidth Control Enabled To enable bandwidth control please click configure Download Enter the download limit for the device Upload Enter the upload limit of the device An entry value of O means no bandwidth limit between the 2 interfaces An entry value of 2000 means 2000Kbit or 2Mbit bandwidth limit b
36. t Explorer J 2 192 168 0 228 x Norton Go to 1982 168 0 228 Ww Favorites If the unit has reset it will go to the default IP address of 192 168 168 1 You will need to change your Ethernet adapter IP address to 192 168 168 x subnet 3 Enter admin in the Username field and password in the Password field and click Login Pro Range User Manual 1 3 Page 5 of 44 SILVERNET Navigation The Pro Range Configuration Interface contains eight main tabs each of which provides a web based management page to configure a specific aspect of the SilverNet device SILVERNET wireless advanced advanced Services wireless network e Status The Status Tab displays device status statistics and network monitoring links e Wireless The Wireless Tab configures basic wireless settings including the wireless mode Service Set Identifier SSID 802 11 mode channel and frequency output power data rate module and wireless security e Advanced Wireless The Advanced Wireless Tab provides more precise wireless interface controls including advanced wireless settings distance settings and signal LED thresholds e Network The Network Tab configures the network operating mode Internet Protocol IP settings DHCP settings and bandwidth control e Advanced Network The Advanced Network Tab provides more precise wireless interface controls when the operating mode is changed to router This include
37. t before data is fragmented into multiple packets If you experience a high packet error rate you may slightly increase the Fragmentation Threshold Setting it too low may result in poor network performance Only minor modifications of this value are recommended Distance To specify the distance value manually enter the value and then click calculate The values for Slot Time ACK Timeout CTS Timeout will be calculated automatically Other Settings Noise Immunity Check to enable When enabled it automatically adjusts the Signal noise level for best performance In a low noise environment it is recommended you turn off this function Signal Strength Indicator RSSI You can configure the LEDs on the device to light up when received signal levels reach the values defined in the two fields Signal Strength Indicator RSSI PSU 100 The default values are 75 30 and 100 40 When the RSSI is greater than 30 the 75 LED will turn on When the RSSI is greater than 40 both the 75 and 100 LEDs will turn on For long distance installations when the signal strength is expected to be lower at about 30 40 the values can be adjusted to compensate The LEDs values can be adjusted as follows e 75 RSSI value 15 e 100 RSSI value 22 Pro Range User Manual 1 3 Page 22 of 44 SILVERNET Radio Off with No Ethernet When checked the device will automatically stop any wireless broadcast if it does not detect any Ethernet connection
38. t side or Wireless side of the device you may lose connection to your PC if the Ethernet port or wireless card is not on the same Tag VLAN ID If this happened use the reset button to clear the config and re configure Pro Range User Manual 1 3 Page 36 of 44 SILVERNET Untagged wireless VLAN to Tagged Ethernet VLAN setup mers WPC2 ssid2 untag vlan ID 200 WPC3 N ssid1 untag vlan ID 100 ssid3 untag vlan ID 300 O Internet access VLAN switch E je lt gt Ethernet port 1 tag vlan ID 100 WP ee ee port2 tag vlan ID 200 O Company Server tag vlan ID 300 port3 tag vlan ID 300 me Video Conference VLAN Switch page setup 2 Q 9 for wireless for Ethernet port add untag vlan ID 100 add tag vlan ID 100 add untag vlan ID 200 add tag vlan ID 200 add untag vlan ID 300 add tag vlan ID 300 add untag vlan ID 400 add tag vlan ID 400 Multiple SSIDs with untagged VLAN connections connecting to a secure wired network with Tagged VLANs Pro Range User Manual 1 3 Page 37 of 44 SILVERNET Services Tab The Services tab configures system management services like ping Watchdog SNMP servers web SSH Telnet NTP DDNS system log and spanning tree SPANNING TREE PROTOCOL STP SETUP Enable STP Root Priority Range 0 to 65536 Root Hello Time Range 1 ta 10 Root Forward Delay Range 4 to 30 Root Maximum Age Range 6 to 40 PING WATCHDOG Enable Ping Watchdog IP Address To Ping
39. te management UPNP Setup UPnP Allows the use of Universal Plug and Play UPnP for gaming videos chat conferencing and other applications Pro Range User Manual 1 3 Page 32 of 44 SILVERNET VLAN Tab The VLAN tab allows you to create multiple Virtual Local Area Networks VLANS Only technically advanced users who have sufficient knowledge about WLAN technology should use the advanced wireless settings VLAN MODES s No Wlan Wlan Switch IEEE802 1p Compatible Wlan Management IEEE802 1p Compatible Qing IEEE802 1p Compatible VLAN Modes No VLAN The device will allow VLANS to pass through ssid ssid A STN thernet A do port 1 tag vlan ID 200 E Ethernet port 1 tag vlan ID 200 ei port2 tag vlan ID 100 Lport 2 tag vlan ID 100 PC1 ethernet PC2 ethernet tag vlan ID 100 tag vlan ID 100 Pro Range User Manual 1 3 Page 33 of 44 SILVERNET VLAN Switch Enables you to add VLAN tags to the Ethernet side and the wireless side of the device including any Virtual Access Points you may have set up VLAN MODES No Vian Wan Switch IEEE802 1p Compatible Wan Management IEEE802 1p Compatible Qing IEEES02 1p Compatible ETHERNET 1 VLAN Default VLAN ID WLAN ID Tag Priority VLAN ID Tag Priority IE IE RADIO VLAN Main VAP1 VAP2 VAPS Default VLAN ID a VLAN ID Tag Priority VLAN ID Tag Priority de 0 7 Ethernet VLAN Tagged VLAN to add a tagged VLAN to the Ethernet port type in the
40. th TKIP Temporal Key Integrity Protocol support only TKIP uses the RC4 encryption algorithm There is a performance limitation to using TKIP so we recommend using AES WPA AES WPA security mode with AES Advanced Encryption Standard support only AES is also known as CCMP Counter Mode with Cipher Block Chaining Message Authentication Code Protocol which uses the AES algorithm WPA2 WPA2 was developed to strengthen wireless encryption security and is stronger than WEP and WPA WPA2 TKIP WPA2 security mode with TKIP support only TKIP uses RC4 encryption algorithm There is a performance limitation to using TKIP so we recommend using AES WPA2 AES WPA2 security mode with AES support only This is the strongest security option available If all of the wireless devices on your network support this option we recommend that you select it Pro Range User Manual 1 3 Page 15 of 44 SILVERNET WEP security WEP 13 Authentication Type Open Shared Key Key Type asci Current Key WEP Key 1 fn WEP Key 1 Length WEP Key 2 PO WEP Key 2 Length WEP Key 3 ma WEP Key 3 Length WEP Key 4 fp WEP key 4 Length MAC ACL Enabled 0 aj Policy Allow hd 3 E Note Operating with WEP security will limit AP to maximum wireless link speed of 54Mbps only Authentication Type Open Authentication Default No authentication We recommend to use this option over shared authentication Shared Authentication May not be co
Download Pdf Manuals
Related Search