LD-5 LED DOME
Contents
1. 32 mm 1 3 in 20 mm 0 8 in 82 grams 2 89 ounces LIGHT SOURCE Mi rmination SOURCE s cocco tt en ale een II 1 x RGB SMD LED Expected LED lifetime at 7096 luminous output 50 000 hours CONSTRUCTION THOUS IG ceret LA A e sta Aluminium body with translucent plastic dome cover Body finish Electrostatic powder coating INSTALLATION Ori amp ntallolo sect aa e ances deca Ret t E ELS cerei terr E LUE Any Diameter of mountig hole 66 80 mm 2 6 3 1 in Maximum thickness of mounting surface 24404422400nsnnnnnsnnnnensnnnennnnnnennnnnennnnnennnnnennnnnnannnnnennnnnn 20 mm 0 8 in Maximum cabled distance from power supply unit to LD 5 LED Dome 3 metres 10 feet Maximum cabled distance between daisy chained LD 5 LED Domes u ennneennenn 3 metres 10 feet 15 OPERATING CONDITIONS Ambient temperature range T ueeneneeeneennnennnenneenenenennnnennnnnnennensnennnennnsnnnennen 10 to 40 C 14 to 104 F Maximum relative h rnidily acord eben 98 PROGRAMMING AND CONTROL ControlinternfaCS D USITT DMX 512 A DMX channel requirements zu gt 3 channels per LD 5 LED Dome self addressing CONNECTIONS LD 5 LED DOME Power and control inputand output 3 uic erro decern ea RJ 45 CONNECTIONS LD 5 INJECTOR DMX GOTO Nsoo 52. electrical dimmer System as this can damage it 10 Boosting power using an additional power supply unit and a power injector When boosting the power to a section of a daisy chain using an additional power supply unit P N 83061702 and a power injector P N 83062010 the same 3 metre 10 feet maximum cabled distance between the power supply and the next LD 5 LED Dome applies The injector should remove any need for splicing or crimping but note that the DMX control signal on pins 1 and 2 continues ff unbroken to each fixture in a daisy chain Boosted power is supplied on pins 3 8 When and patching or crimping power and control cables it is important to note that the LD 5 LED Dome uses unbalanced DMX that is to say that DMX control only uses pins 1 and 3 of the XLR connectors and pins 1 and 2 of the CAT5 RJ45 connectors Pins can be identified on an RJ45 connector by placing it so that the copper connectors face downwards pin 1 is on the left side 11 Installing an LD 5 LED Dome The LD 5 can be installed in any orientation A hole of the appropriate size must be cut in the mounting surface prior to mounting the LD 5 When mounting LD 5 s in a wall or ceiling space draw and attach the injector and patch cables and connect these before you insert the LD 5 LED Domes min 66 mm max 80 mm min 2 6 in max 3 1 in max 20 mm max 0 8 in Measurements in millimeters a
3. dSSGM 125 por LED DOME LD 5 LED Dome dimensions 140 mm 5 5 in 66 mm i ii 2 6 in 20 mm 0 8 in 32 mm 1 3 in Measurements in millimeters and inches in brackets Drawing not to scale LD 5 LED DOME USER MANUAL REV 2 2013 SGM Information subject to change without notice SGM and all affiliated companies disclaim liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual The SGM logo the SGM name and all other trademarks in this document pertaining to services or products by SGM or its affiliates and subsidiaries are trademarks owned or licensed by SGM or its affiliates or subsidiaries This edition applies to firmware version 1 or later English edition Contents Safety MO Mal seen 6 OVEIVI OW 7 Installing an ES LED DOME a u an a 12 DMX control etr 13 SONICO p E 14 Specifications cocccccnncnnnncnnonnnnnennnennnennnnnononnnnnnnnnnnnnrnnnnnnnrnnnnnnnnnnnnnnnnnnnneninnss 15 User s NOLES cido ia A A E E 17 Safety information WARNING Read the safety precautions in this section before installing powering or operating this product The LD 5 is intended for professional use only It is not suitable for household use Review the following safety precautions caref
4. in are connected using standard CAT5 or a higher standard patch cables not supplied attached using the RJ45 connections on the rear of each LD 5 through which power and control signals are sent DMX data Data return 24 Vdc LD 5 Injector Max 3 meter Ordering code Minimum 83062009 Cat 5 standard RJ45 RJ45 am Back NS Do not 24 Vde terminate See cable length table 1 2 3 See cable length table 5 S E E x E gt 5 PIN XLR Power Injector Ordering code 83062010 Power supply Ordering code 83061702 XLR pinout Power supply Pins 1 and 3 Ordering code 83061702 A single power supply can drive multiple LD 5s but note that the strength of the current falls between each LD 5 and the degree of this drop is also dependent on the length of the cable The following table provides some guidelines but for additional guidance contact SGM or your local distributor Number of LED Domes per power supply Number of LED Domes Maximum length of CAT5 patch cable between LED Domes 15 3 metres 10 feet 20 2 m 6 5 ft 25 1 5 m 5 ft 30 1 m 3 3 ft 35 0 5 m 1 5 ft As the table indicates the greater the distance between each LD 5 the fewer fixtures per power supply and vice versa if you increase the number of LD 5s you effectively reduce the corresponding maximum distance between them For daisy chains with many fix
5. nd inches in brackets 12 DMX control LD 5 LED Domes can be controlled using any DMX512 compatible DMX controller that supports the size of your installation For chains or arrays of LD 5s we recommend the use of a controller that has pixel mapping functionality About DMX Each individual LD 5 can be controlled using signals sent by a DMX controller over three channels The first channel used to receive data from a DMX control device is known as the DMX address Each LD 5 sets its own DMX address automatically The first LD 5 is set to DMX address 1 and the next fixture sets itself to 4 and so on in increments of three channels per fixture For example if an LD 5 has a DMX address of 7 then it uses channels 7 8 and 9 The following fixture in the DMX chain will have a DMX address of 10 It is not possible to otherwise manually set or force the DMX address of an LD 5 LED Dome DMX protocol LD 5 LED Dome 3 channel DMX RGB Channel Value Percent Function 1 0 255 0 100 Red 0 100 2 0 255 0 100 Green 0 100 3 0 255 0 100 Blue 0 100 13 14 Service There are no user serviceable components in the device Do not open the LD 5 as doing so is likely to damage it Consult your SGM dealer if the device operates abnormally is defective or otherwise in need of service or repair Specifications PHYSICAL LD 5 LED DOME Length x depth Heightsin ee 80 x 80 x 52 mm 3 1 x 3 1 x 2 1 in
6. pin XLR male LD 5 POWER SUPPLY ELECTRICAL BEIPOWER OU nee T ea 24V 50W AC mains POWER Miss ce Pt pred ete eunte ceti Gaeta a ett 100 240 V AC 50 60 Hz ORDERING INFORMATION 11 5 Power SUPDIV Dil oon erret ee uH ecco EE Re ed cu una ee a ue eb C reo PR Haeo P N 83061702 LDS ja T voro DE P N 83062009 2 5 Power Ifie closure n ccr eter atc at acento erste ee eva tut epee En yo P N 83062010 ie Specifications subject to change without notice User s notes 17 18 19 SGM A S Soeren Frichs Vej 51 53 DK 8230 Aabyhoej Denmark Tel 45 70 20 74 OO info sgmlisht com www ssmlight com
7. tures or larger distances between each fixture additional power supply units can be used to boost the power via injector cables both sold separately The maximum cabled distance between a power supply unit and the first LD 5 LED Dome and between successive LD 5s is 3 metres 10 feet The theoretical maximum number of LD 5s in a controllable daisy chain is 170 but additional fixtures can be controlled in an installation using multiple DMX universes and separate daisy chains each of up to 170 fixtures Each fixture uses three DMX control channels and the maximum number of channels in a DMX universe is 512 3 x 170 510 channels Note that the last fixture in a daisy chain must not be terminated Power supply unit The LD 5 power supply unit transformer can operate on any 100 240 V 50 60 Hz AC mains power supply and supplies 24 V DC to LD 5 LED Domes via an injector for the first power supply in a daisy chain of LED Domes P N 83062009 or power injector for subsequent booster power supplies in a daisy chain of LED Domes P N 83062010 Splicing or connecting a power supply unit to mains supply injector or power injector must carried out by a qualified electrician Power supply units must be grounded earthed and be able to be isolated from AC power The AC power supply must incorporate a fuse or circuit breaker for fault protection Do not open a power supply unit to replace the supplied power cable or connect the device to an
8. ully before installing or operating the device Do not open the device there are no user serviceable parts inside Ensure that power is cut off when connecting the device and its power supply unit to the AC mains supply Ensure that the power supply units are electrically connected to earth ground Do not apply power if the device or mains cable is in any way damaged Do not immerse the fixtures in water or liquid Install only in accordance with applicable building codes Do not paint cover or modify the device and do not filter or mask the light Installation must be performed by a qualified electrician Overview The LD 5 LED Dome is a DMX controllable effect light incorporating red green amp blue RGB color mixing It is designed for permanent indoor installation and is ideal for pixel arrays or similar daisy chained arrays of multiple LD 5s or similar DMX controllable effect fixtures LD 5 LED Domes have an LED life expectancy of 50 000 hours Preparing for installation Each LD 5 LED Dome must be connected directly or indirectly in the case of a daisy chain of connected LD 5s to an LD 5 power supply unit sold separately P N 83061702 that is connected to mains supply and a DMX compatible control device not supplied The first fixture in a daisy chain or a single LD 5 is connected to the power supply and DMX controller via an injector sold separately P N 83062009 Subsequent LD 5s in the daisy cha
Download Pdf Manuals
Related Search