WT-1671 GSM Trap Alarm System USER MANUAL
Contents
1. WT 1671 GSM Trap Alarm System USER MANUAL WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 Introduction The new Animal trap alarm allows you to be alerted via SMS whenever an animal trap has been activated and an animal has been captured This allows a quick response to attend and recover the animal and reduce the stress and suffering for the animal This unique system will also save valuable travelling costs and time when having to manually check each remote animal trap daily The concept is extremely simple and the unit remains completely dormant using no power until the system is activated by the sprung loaded door removing the Magnet Key from its holder Once the Magnet Key is removed the system immediately boots up on to the local Mobile Phone Network and can send a customised S M S text alerts to up to 5 separate telephone numbers The system comes with two Rechargeable Battery so as to be able to keep one fully charged at all times The system is Dual Band or Quad Band and will accept any Global Network GSM SIM Card WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 Step 1 The simplest set up methods to set up Administrator number Applied the KISS Principle keep it simple stupid The GSM Remote Control Switch is easy to setup and use Insert the SIM card simply use your mobile phone call to the unit your mobile phone number will automati2. CSQ 5 12 Signal too weak system not function CSQ 13 24 Signal Good System function well CSQ 25 32 Signal Excellent System working well SMS Reply Message when the system ON OFF 21 N Message switch lt ON gt 2013 10 10 17 06 Thu N 0 means SMS Reply Message when the system OFF N 1 means SMS Reply Message when the system ON Factory Default as SMS Reply Message when the system ON If setting to not receive SMS Reply Message when the system OFF the unit will return a message indicate successful setting for the command and it will no longer sending SMS reply until the setting of SMS Reply Message when the system ON is done When the system having the temperature alert wireless alarm alert it will automatically sending the alert message to the Admin WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 9 Edit Input Messages for the system 26 N XXXXXXXX When Setting as N 0 means Edit for Input and 9 Channels Wireless Alarm 26 0 The equipment Messages for the system when Alert Messages has already started switch on System Default Startup user defined System startup Master relay information The lt OFF gt equipment has N 01 09 means Edit for Input already started Alert Message for which channel of Wireless Alarm 2013 10 10 17 24 Thu Equipment that connected System Default Wireless When Setting as alarm 1 Please timely 26
3. damage mechanical shock water damage fire damage or damage arising out of abuse and improper application of the equipment Note Wherever possible return only the PCB to Witura Service Centres DO NOT return the enclosure The WT 1671 is a product of Witura Technology Sdn Bhd And is manufactured by Shenzhen Witura Telecommunications Co Ltd WARNING For safety reasons only connect equipment with a telecommunications compliance label This includes customer equipment previously labelled permitted or certified WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2
4. registered with the network provider before they can be used usually by calling the network provider or registering on their website please refer to the instructions supplied with your SIM card During the registration procedure a confirmation code or text message is usually sent to the SIM cards telephone number to be able to read and react to the message you will need to insert the SIM card into an unlocked mobile phone After successfully registering the SIM card ensure there is sufficient credit on the card for programming confirmation texts to be sent from the GSM Remote Control Switch You MUST ensure that the PIN request is disabled from the SIM card before inserting it into the GSM Remote Control Switch If you do not disable the PIN request the GSM Remote Control Switch will not work If the PIN request is not disabled and the unit is switched on more than 3 times you will have to reset the PIN using the PUK code which will have to be obtained from the service provider To check the PIN request status of your SIM card place the card in an unlocked mobile phone switch the phone on If you are able to make calls without entering a PIN number the PIN request is disabled If a PIN number is requested refer to the instructions supplied with the SIM card and then look through the phones options for the disable PIN request and disable it You MUST disable any voicemail that is set up on the SIM card the codes shown below are
5. system alarm alert messages 28 N When Setting as 28 00 Startup user defined message 2013 10 10 17 42 Thu N 00 means Delete the Input Messages for the system when switch on N 01 09 means Delete the Input Alert Message for which channels of Wireless Alarm Equipment that connected N 10 means Delete Input Alert Message for line cut alert N 11 means Delete Input Alert Message for pulse counter when it reach the value set If there is no text message programmed it will return a SMS with Blank Message 12 Restart System After sending the command 33 system will restart and after 15 30second will hear a di sound If before the restart the system is in armed status all the admin number will receive System startup Master relay lt OFF gt 2013 10 15 16 34 Tue Restart System WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 Step 3 Installation Production Specifications Operation Voltage 12 volts DC Operating Current Maximum 500mA typically 55mA GSM Frequency MHz GSM900 1800Mhz or GSM850 900 1800 1900Mhz Humidity Less Than 80 RH Operating Temperature 20c to 55c Physical Size 130 x 100 x 50mm Protection IP 65 Weather Proof Casing Approvals C E FCC ETSI WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 eo Preparing the SIM card All new SIM cards have to be
6. 01 The door precessing closed N 10 means Edit for Input Alert Wireless 1 defined Message for line cut alert information The door System Default Alarm The closed line s status changes N 11 means Edit for Input Alert 2013 10 10 17 21 Thu Message for pulse counter when it reach the value set When Setting as System Default The counter is 26 10 Line Alarm full already Line user defined message Line Alarm XXXXXXX is the text messages content which can up to 69 2013 10 10 17 21 Thu alphabet When the text message content successfully When Setting as programmed it will overwrite 26 11 Fulll the system default text Counter user defined messages message Full 2013 10 10 17 21 Thu 10 Check input messages programmed 27 N When Setting as N 00 means Check the Input in the system alarm alert messages 27 01 Wireless 1 defined information The door closed 2013 10 10 17 40 Thu Messages for the system when switch on N 01 09 means Check the Input Alert Message for which channels of Wireless Alarm Equipment that connected N 10 means Check Input Alert Message for line cut alert N 11 means Check Input Alert Message for pulse counter when it reach the value set If there is no text message programmed it will return a SMS with Blank Message WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 e 11 Delete input messages programmed in the
7. cally register as the 1st Administrators You will receive the following SMS message from the unit Administrator 1 18617185300 your phone number Zi 3 4 5 Call to the SIM Card No Of WT 1671 Return Text Messages Administrator 1 18617185299 eS 2 31 pm i lt Messages WT 1671 Contact Administrator You already finish the set up Now you can use your mobile phone call to the SIM Card number switch the device on permanently Another call to the SIM Card will switch the device off permanently If you do not required to go through details setting please process to STEP3 Final Installation and Wiring WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 Step 2 Advance Set Up First Step of programming you must enter the factory passwords of 1234 and go programming mode inside the You only can perform the next commands after enter into programming mode 0 1234 You get administrator privileges 2013 10 09 00 33 Wed When you enter 0 1234 you enter into the programming mode You must perform the next command in 10 minutes If you did not do anything the system will exit from programming mode Change Password Add telephone number into the 0 1234 new password For example if you need to change to the new PW of 1212 0 1234 1212 1 1 telephone number New password lt 1212 gt 2013 10 10 16 07 Thu Adminis
8. for UK networks only please refer to your network operator if outside the UK Vodafone 1210 gt Send you will hear order is accepted and confirmed 02 Call 1760 gt Send you will hear order is accepted and confirmed T Mobile Call 222 and follow instructions Orange Call 450 and follow instructions The SIM card is now ready to use We recommend that if you are using a pay as you go PAYG SIM card that you choose to automatically Top Up when the cards credit falls below a certain limit please contact your network provider or visit their website for more details Most but not a using post paid SIM cards will be de activated by the network if not used to make an outgoing voice call or send an SMS text message within a specific period To prevent this simply send the GSM Remote Control Switch a text command 0 PWH then 2 it will reply by text message do this once a month to keep the SIM card active WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 El Warranty Witura Technology Sdn Bhd warrantees the WT 1671 GSM Trap Alarm System against defective parts and workmanship Witura Technology Sdn Bhd shall at its option repair or replace the defective equipment upon the return of such equipment to any Witura branch This warranty applies ONLY to defects in components and workman ship and NOT to damage due to causes beyond the control of Witura such as incorrect voltage lightning
9. trator Maximum 4 digits of passwords If you decide to protect your privacy you can change the factory password to your new password Enter the factory password follow by your new password Set Admin Numbers admin list 1 15989427391 1 1 set 1st admin number For example set Admin number 2 18617185300 1 2 set 2nd admin number 18617185300 into admin 2 3 1 3 set 3rd admin number 4 1 4 set 4th admin number 1 2 18617185300 5 1 5 set Sth admin number 2013 10 10 16 08 Thu Only the number in the list can receive alarm texts message and active the relay output You can add up to 5 telephone number into the admin list Check phone number you ae Administrator program in the list 1 15989427391 2 18617185300 3 4 5 2013019019 16 09 Thu Delete the admin number in the 3 N Administrator Delete Admin Number list N Admin number 1 5 For example if you want to delete admin no 2 just enter 3 2 1 15989427391 2 3 4 5 2013019019 17 16 Thu Delete 1st admin 3 1 Delete 2nd admin 3 2 Delete 3rd admin 3 3 Delete 4th admin 3 4 Delete 5th admin 3 5 WITURA TECHNOLOGY SDN BHD WT 1671 GSM Trap Alarm System User Manual V1 2 Check Signal Strength 5 CSQ lt 28 gt 2013 10 10 16 11 Thu You must confirm the signal strength at site before you install the unit If the signal too weak the unit will not function properly
Download Pdf Manuals
Related Search