User Manual - Boardman Medical Supply
Contents
1. Grounding reliability can ONLY be achieved when the equipment is connected to a receptacle marked Hospital Only or Hospital Grade Rev D 1 02 00 P N 034059 _ WARNING B For proper grounding junction box MUST be securely connected to the bed with metal screws and spacer provided or electrical shock could occur 1108103 RevA 1 08 01 Part No 1123842 7 Invacare Model BAR600IVC Bariatric Bed 2 OVERVIEW NOTE Labels located on bed frame N WARNING The Bariatric Bed is NOT designed to be used as a D WARNING i transport When The weight limit of the occupant of the AL transporting a patient use Bariatric Bed CANNOT exceed 600 Y x pounds The TOTAL weight limit of the approved patient Bariatric Bed including accessories transport Otherwise injury mattress occupant and ANY other person object positioned on the bed or damage may result cannot exceed 700 cep Rev 1 01 04 P N 1098347 Invacare IVC Model BAR600IVC Bariatric Bed 8 Part No 1123842 2 OVERVIEW 2 20 Typical Product Parameters IVC BARIATRIC BED FOOT END MINIMUM 26 25 inches 66 7 cm MAXIMUM 33 75 inches 85 7 cm DECK HEIGHT MINIMUM DOWN POSITION 14 inches 35 cm 2 inches MAXIMUM UP POSITION 22 i2. JL JA m mo n Motor Shaft End B Foot Section Motor Shaft End Head Section 4 FIGURE 3 Emergency Crank 4 3 Optional Bed Rails A WARNING DO install the optional bed rails without reading and understanding the Bed Rail Risk Notification Guide that accompanies this manual and is included with each bed rail kit The Bed Rail Risk Notification Guide can also be found at www invacare com Invacare IVC Model BAR600IVC Bariatric Bed 20 Part No 1123842 5 MAINTENANCE 5 Maintenance 5 Washing Bed Ends CAUTION DO NOT wash head or foot section AC motors and electronics are not water proof To protect flooring ensure bed ends are completely drained and dry before placing on flooring Otherwise remaining dirty water may damage or stain flooring Avoid spraying water directly into the gear box ends Otherwise damage to the gear box may occur Standor prop each bed end in an upright position on its legs 2 Using a mild soap detergent and soft bristle brush or sponge scrub all exterior surfaces 3 Using a hose and nozzle attachment rinse bed ends thoroughly w
3. Drive Shaft Hi Lo Motor Output Shaft d Full Electric Only Hi Lo Motor Hi Lo Motor Output Shaft Output Sid Spring Loaded Coupler utput Side Top Gear Box Output Drive Shaft Bottom Gear Box Output Drive Shaft Covered Input Drive Shaft Covered Drive Shaft Cover FIGURE 10 Assembling Installing Removing Drive Shaft Part No 1123842 43 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP Inspecting the Bed WARNING The removal and installation of cables are to be performed by a qualified technician Before installing the connector into the junction box be sure the side with the locking tab is facing downward otherwise injury or damage may occur CAUTION cable connections MUST be aligned properly Align locking levers with locking tabs for proper connection Mis alignment of cable connections will cause permanent product damage For this procedure refer to FIGURE 11 connectors will arrive plugged into the junction box I Check all electrical connections on junction box at foot end to ensure that all motors are plugged into the correct locations 2 Plug the junction power box cord into a 10 volt outlet CAUTION cable connections MUST be aligned properly Align locking levers with locking tabs for proper connection Mis alignment of cable connections will cause permanent product damage 3 If equipped with a crossove
4. Connect the crossover cable to the cable from the head actuator Long Crossover Cable For this procedure refer to FIGURE 8 on page 39 the crossover cable from the junction box through the two loops in the head end 2 Connect the crossover cable to the short cable from the head actuator 3 Gently pull the crossover cable toward the junction box so that any slack in the cable is taken up near the junction box Part No 1123842 37 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP SHORT CROSSOVER CABLE 1 1 Connection of Crossover ble to Head Actuator Si E Ss 4 9 L9 V Bottom View Junction of Bed E Box ol Head Rx Actuator Sech dee t Foot End Head End of Bed of Bed 4 amp 9 a Je EX f CAUTION All cable connections MUST be aligned properly Align locking levers with locking tabs for prope
5. Model BAR600IVC Bariatric Bed 6 Part No 1123842 2 OVERVIEW 2 Overview 2 1 Label locations CAUTION All cable connections MUST be aligned properly Align locking levers with locking tabs for proper connection Mis alignment of cable Serial number label located here WARNING ELECTRICAL GROUNDING INSTRUCTIONS This device is equipped with o three prong grounding plug for your protection against possi ble shock hazards Where two prong receptocle is en countered it is the per sonol responsibility ond obligation of the er to contoct qualified electrician ond hove it reploced with o properly grounded three prong wall receptacle in accordance with the no tionol electrical code If you must use on exten Sion cord use only a three wire extension connections will cause permanent product damage Locking Lever Locking Tab cord having the some or higher electricol roting os ihe device being nected Head Motor Crossover Cable Cable Do not under any cir cumstonces cut or remove round grounding prong from this plug DO NOT REMOVE THIS TAG 1013763 PINTITITIO Rev A
6. Shaft Spring Loaded End First Second Third Storage Spring Button 4 CQ gt Plastic Caps FIGURE 9 Assembling Installing Removing Drive Shaft 6 Locate the Hi Lo motor output shaft spring loaded coupler If necessary shift the bed end to the right or left to align the Hi Lo motor output shaft spring loaded coupler with the foot end gear box 7 Ensure the Hi Lo motor output shaft spring loaded coupler is properly aligned with the foot end gear box as shown in Detail A of FIGURE 10 Part No 1123842 41 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP 8 Release the Hi Lo motor output shaft spring loaded coupler by pushing in against the Hi Lo motor output shaft spring loaded coupler and turning clockwise The coupling will release and engage the foot end top gear box output shaft cross pins 9 Ensure that all components are securely installed A WARNING Close the drive shaft covers over all drive shafts that are not in use before placing the bed in service Otherwise damage or injury may occur Invacare IVC Model BAR600IVC Bariatric Bed 42 Part No 1123842 8 PACKAGING HANDLING AND SET UP Locked Position DETAIL Drive Shaft H i Lo Motor Output Shaft Full Electric Only Hi Lo Motor Output Shaft Spring Loaded Coupler Gear Box Output Drive Shaft Unlocked Position Hi Lo Motor Output Shaft Spring Loaded Coupler
7. all bed components for damage or excessive wear Visually examine all welds for cracks Inspect the head and foot spring sections for bending warping or damage Check drive shaft and drive shaft connections for bending damage or excessive wear Oooo Inspect pull tubes and mounting hardware for bending damage or excessive wear Part No 1123842 47 Invacare IVC Model BAR600IVC Bariatric Bed 9 MAINTENANCE LI Inspect all bolts and rivets to ensure that they are securely tightened and functioning properly Inspect bed ends for proper operation A Adjust bed ends to the lowest position Remove bed ends from head or foot spring Remove bed end caps and plastic cover Inspect cables and pulleys for wear Inspect Acme screws for lubrication Apply a light lithium based grease if necessary monos Reinstall the plastic cover and end caps Check casters to ensure they lock if applicable and roll properly Electrical Inspection and Maintenance Coco Inspect all electrical bed components for damage or excessive wear i e cracked or broken housings or worn components Check pendant power and motor cords for chafing cuts or excessive wear Make sure all plugs are fully attached and free of damage Check all functions head foot and bed ends raise and lower properly Inspect all electrical bed components Chafing Nicks in the insulation Missing insulation Exposed internal wiring o
8. hardware for bending damage or excessive wear Inspect all bolts and rivets to ensure that they are securely tightened and functioning properly Check sleep surfaces to ensure all links are intact UUUUUUU OU Check casters to ensure they lock if applicable and roll properly Electrical Inspection and Maintenance Inspect all electrical bed components for damage or excessive wear e cracked or broken housings or worn components Check pendant power and motor cords for chafing cuts or excessive wear Make sure all plugs are fully attached and free of damage Invacare IVC Model BAR600IVC Bariatric Bed 22 Part No 1123842 5 MAINTENANCE Check all functions A Head raises and lowers properly B Foot raises and lowers properly C Bed ends raise and lower properly PASS FAIL PASS Bed and all components have passed all of the preceding inspection criteria and the bed is ready for placement into a client s home Q FAIL Bed or any component has failed any of the preceding inspection criteria Tag the bed or component with a complete description of the failure s and have the bed serviced Part No 1123842 23 Invacare Model BAR600IVC Bariatric Bed 6 TROUBLESHOOTING 6 Troubleshooting A WARNING Read all general guidelines warnings and cautions before performing any repair maintenance on the bed All repair and maintenance on the bed should be performed by a qualified technician
9. head section Ends Invacare IVC Model BAR600IVC Bariatric Bed 28 Part No 1123842 8 PACKAGING HANDLING AND SET UP Foot Section Not shown Packing inserts junction box with cord motors with cables attached pendant emergency crank handle and owner s manual FIGURE 2 Unpacking Foot and Head Sections 8 3 Inspecting Examine each item carefully for scratches nicks dents or any other apparent damage Check all parts for shipping damage In case of shipping damage DO NOT use Contact Dealer Carrier for further instruction Inspect the power supply cord and cables for cuts or damage to the cord and or plug 2 Inspect the junction box for any damage to the connectors 3 Ensure that the motor plugs are plugged into the junction box and fit properly Part No 1123842 29 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP 8 4 Set Up Assembling Disassembling Head and Foot Sections A WARNING DO NOT attempt to operate bed controls prior to completion of assembly as damage to bed components or personal injury may occur For this procedure refer to FIGURE 4 on page 33 Assembling Remove the head section of the bed from the packing carton Place the head section on a flat surface so that the motor guards on the bottom of the frame are supporting the head section 2 Remove the foot section of the bed from the packing carton 3 Remove tie wraps securing the cabl
10. the truck driver sign the copy acknowledging the count 4 If shortage occurs IMMEDIATELY contact Invacare Customer Service department 800 333 6900 8 2 Unpacking The bed is contained in three cartons Check bed components for any obvious damage to the carton or its contents If damage is evident contact your local Invacare dealer 2 Remove any loose packing from the cartons 3 Carefully remove all components from the cartons A WARNING DO NOT plug the power cord into a power source until assembly is complete To do so could result in damage or personal injury DO NOT attempt to operate bed controls prior to completion of assembly Otherwise damage to bed components may Part 1123842 27 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP Unpacking Bed Ends For this procedure refer to FIGURE 1 on page 28 Drive Shaft bed end carton includes Two bed ends Four casters two locking and two non locking casters One drive shaft assembly in two pieces Bed Casters Located in Lower Carton Insert FIGURE Unpacking Bed Ends Unpacking Foot and Head Sections For this procedure refer to FIGURE 2 on page 29 The foot section carton includes One foot section including pendant junction box with power cord and foot and hi lo motors with cables One emergency crank handle 2 head section carton includes One
11. 6 Troubleshooting Electrical SYMPTOM PROBABLE CAUSE Bed section does not move End of stroke reached SOLUTIONS Operate opposite button Bed not plugged in Ensure power cord is plugged into power source Pendant not functioning Ensure Pendant correctly connected to junction box Ensure Pendant cable is not entangled pinched Full Electric Bed Hi Lo func Cables tion does not work Ensure cables are not entangled pinched Call the dealer for repair replacement of cables and or motors Household fuse or breaker blown Check household fuse breaker box Motors are not functioning Call dealer moving Hi Lo Motor Ensure cables are not entangled or pinched Ensure drive shaft is correctly installed Bed Spring does not stop Pendant Check for depressed stuck buttons If button is stuck call dealer for repair Bed Hi Lo movement does not stop Check cables If damaged call dealer Invacare IVC Model BAR600IVC Bariatric Bed 24 Part No 1123842 6 TROUBLESHOOTING 6 2 Troubleshooting Mechanical SYMPTOM PROBABLE CAUSE SOLUTIONS Bed does not stay in place Locking casters not locked Lock casters Bed sections do not move Pull tube Check pull tube s for binding Call dealer for repairs Bed ends move in opposite directions electrical Drive shaft connected to wrong gear Call dealer or manual bed box shaft Hi Lo fu
12. Invacare IVC Model BAR600IVC Bariatric Bed User Manual For more information regarding bed rail safety refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com This manual MUST be given to the user of the product BEFORE using this product read this manual and save for future reference Yes you can 2011 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Invacare IVC Model BAR600IVC Bariatric Bed 2 Part No 1123842 CONTENTS GENERAL 5 dnd aN atelectasis aan ate 5 Limited Warr nty AEN 6 OVERVIEW 7 E bIlecilre 7 Typical Product Parameters ER e OR ec e on idee geet Ee 9 are e ERU eU UID R ut t LUN etes pete ete HERE IRE iba eei eub obedece 9 SAFETY 10 VEER TE 10 OPERATION AND ADJUSTMENT 18 Operating Bariatric Bed eegene 18 Emergency Crank 19 Optional Bed Rails 20 MAINTENANCE 21 Washing aut M I 21 Gleaning Head and Foot Sections idet pH dH ERI E ERREUR de EENS 22 Maintenance and Cleaning Checker greng tet t ettet to Ru e
13. ODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LIMITATION OF HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Invacare IVC
14. Remove the drive shaft Refer to Assembling Installing Removing Drive Shaft on page 40 Disconnect the crossover cable For the crossover cable definition Refer to Connecting Crossover Cable on page 37 wt ow M Remove both bed ends Refer to Installing Removing Bed Ends on page 34 Place the bed on a flat surface so that the motor guards on the bottom of the frame are supporting the bed Starting with one side of bed pull the release pin and pull the head section so that it starts to separate slightly from the foot section On the opposite side of bed pull the release pin Separate the head section from the foot section Invacare IVC Model BAR600IVC Bariatric Bed 32 Part No 1123842 8 PACKAGING HANDLING AND SET UP Foot Section Inside Motor guards located on underside of frame sections Head Section Inside Foot Section Head Section FIGURE 4 Assembling Disassembling Head and Foot Sections Part No 1123842 33 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP Installing Removing Bed Ends A WARNING DO NOT place your hand between the head section and the bed end while assembling Otherwise injury may occur Reverse this procedure to remove the bed ends l Stand one bed end as close to the head section as possible With one hand grasp the head section and raise it until the corner plate head rivets of the section are high enough to place i
15. are not included with the bed contact an Invacare dealer To install casters lay the bed ends flat on the floor 2 Insert the caster shaft into the caster socket 3 prevent excess movement of the bed during assembly lock each of the two locking casters by pushing down on the caster lock Locking the casters may not prevent the bed from moving on slick or slippery surfaces 4 unlock each of the two locking casters push down on the caster lock labeled off Part No 1123842 35 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP Caster Socket Caster Shaft Caster Non Locking Caster Socket Locking Caster Locking Caster FIGURE 6 Installing Casters Invacare IVC Model BAR600IVC Bariatric Bed 36 Part No 1123842 8 PACKAGING HANDLING AND SET UP Connecting Crossover Cable WARNING Ensure that the crossover cable does not hang loosely below the side channel Otherwise the cable could present a tripping hazard Crossover Cable Definition The crossover cable is defined as the cable that connects the junction box to the head motor actuator If the crossover cable is 43 inches long refer to Short Crossover Cable on page 37 If the crossover cable is 84 inches long refer to Long Crossover Cable on page 37 Reverse this procedure to disconnect the crossover cable Short Crossover Cable For this procedure refer to FIGURE 7 on page 38 l
16. are properly and securely in place before using the manual electric bed recommends that the mattress be centered on the bed frame Otherwise individuals may become entangled between the bed rail and the bed frame Physically challenged individuals who cannot prevent themselves from rolling climbing out of the manual electric bed may require alternative safe means of restraint When used with a manual electric bed the bed rails DO NOT fall under any weight limitations Bed rails can be deformed or broken if excessive side pressure is exerted on the bed rails These bed rails are used for the purpose of preventing an individual from inadvertently rolling out of bed The bed rails are not intended nor may be used for restraint purposes If an individual is capable of injuring himself herself a physician or a healthcare professional should be consulted for alternative means of safe restraint After raising lowering the head foot end of the electric bed check the distance between the bottom of the bed rail and the mattress If there is excessive distance between the bottom of the bed rail and the mattress in which individuals may become entangled adjust the height of the bed rail if applicable or provide alternative means of patient protection DO NOT use the side rails as push handles for moving the electric bed Replacement mattresses and bed side rails with dimensions different from the original equipment supplied or specified b
17. ation below for definitions of the signal words DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient trouble free use Part No 1123842 5 Invacare Model BAR600IVC Bariatric Bed GENERAL 1 2 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the mechanical and electrical components of this product when purchased new and unu
18. efore cleaning Clean up the spill and allow the electric bed or the area around the electric bed to dry thoroughly before using the electric controls again The manual electric bed is not designed to be used as a patient transport When transporting a patient use an approved patient transport Otherwise injury or damage may result When operating moving electric beds AL WAYS ensure that the individual utilizing the bed is positioned properly within the confines of the bed DO NOT let any extremities protrude over the side or between the bed rails when performing these functions After the electric bed has been assembled ALWAYS test to make sure that all sections of the electric bed are properly and securely in place before using Make sure head and foot springs sections are connected securely to the bed ends before use The pendant and power cords MUST be routed and secured properly to ensure that the cords DO NOT become entangled pinched and or severed during operation of the electric bed Invacare IVC Model BAR600IVC Bariatric Bed 12 Part No 1123842 3 SAFETY A WARNING NEVER operate the unit if the cords are damaged If the unit is not working properly call a qualified technician to examine the unit and repair it Keep all moving parts including the main frame mattress deck head and foot springs sections and all drive shafts free of obstruction i e blankets sheets heating blankets pads tubing wiring etc and other types of
19. es ci ec Petre eres cus 22 TROUBLESHOOTING 24 Troubleshooting Electrical Do E de po RE a een edente e 24 Troubleshooting 25 ASSEMBLY MAINTENANCE AND ADJUSTMENT SECTIONS FOR DEALERS ONLY 26 Overview of PtOCed res eset eripere Eeer 26 PACKAGING HANDLING AND SET UP 27 Part No 1123842 3 Invacare Model BAR600IVC Bariatric Bed CONTENTS Dies M c 27 Bird d M 27 INSPSCtinig DNO EDD 29 Set Up 30 Storing D D mc ad 45 MAINTENANCE 46 Washing Bed ME 46 Cleaning Head andi Foot Sections o e e D e P Ee ett E ER eee Et i pet te ob 47 Maintenance Checklist 2 TROUBLESHOOTING 50 Troubleshooting P 50 Troubleshooting e EH RE EENEG 51 Invacare IVC Model BAR600IVC Bariatric Bed 4 Part No 1123842 GENERAL General 1 1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage See the inform
20. es for shipping FIGURE 3 on page 31 Place the foot section on a flat surface so that the motor guards on the bottom of the frame are supporting the foot section Invacare IVC Model BAR600IVC Bariatric Bed 30 Part No 1123842 8 PACKAGING HANDLING AND SET UP Tie Wrap Tie Wrap 4 Align the inside of the head section with the inside of the foot section Locking pins are located on the foot section frame and will make an audible click when properly engaged with the head section frame 5 Push the head section towards the foot section so that the head section frame slides into the foot section frame and the locking pins engage Ensure the locking pins are properly engaged by attempting to pull the head section from the foot section If the sections separate repeat STEP 5 6 until the locking pins are secure 7 Install the bed ends Refer to Installing Removing Bed Ends on page 34 8 Connect the crossover cable Refer to Connecting Crossover Cable on page 37 9 Assemble and install the drive shaft Refer to Assembling Installing Removing Drive Shaft on page 40 10 Activate the bed functions Refer to Inspecting the Bed on page 44 Part No 1123842 31 Invacare IVC Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP Disassembling Lower the head and foot sections completely Refer to Raising and Lowering on page 19 Lower the bed to the lowest height Refer to Raising and Lowering on page 19
21. ith plain cold or warm water Do not exceed a water temperature of 110 F Use household tap pressure DO NOT use pressure washers or steam cleaners 4 Tip bed end from side to side to allow any collected or trapped water to drain 5 Thoroughly towel dry bed end and all components 6 Repeat drying process until all components are dry Ensure that the bed end is completely dry before storing Gear Box 0 FIGURE Washing Bed Ends Part No 1123842 21 Invacare Model BAR600IVC Bariatric Bed 5 MAINTENANCE 5 2 Cleaning Head and Foot Sections Unplug the power cord of electric beds before performing maintenance 2 Wipe down the bed with disinfectant Allow it to dry completely 5 3 Maintenance and Cleaning Checklist Invacare recommends the following maintenance and cleaning procedures be conducted between uses and at least once every three years This form is provided as a guide to help with documentation Cleaning and Disinfecting Bed Unplug the power cord of electric beds before performing maintenance Wipe down with disinfectant Allow to dry completely Mechanical Inspection and Maintenance Inspect all bed components for damage or excessive wear Visually examine all welds for cracks Inspect the head and foot spring sections for bending warping or damage Check drive shaft and drive shaft connections for bending damage or excessive wear Inspect pull tubes and mounting
22. les Ensure motor cable s correctly connected Refer to FIGURE 11 Ensure cables are not entangled pinched Call the dealer for repair replacement of cables and or motors Household fuse or breaker blown Check household fuse breaker box Motors are not functioning Call dealer Hi Lo Motor Ensure Hi Lo motor cable is correctly connected Refer to FIGURE 11 Ensure cables are not entangled or pinched Ensure drive shaft is correctly installed Bed Spring does not stop moving Pendant Check for depressed stuck buttons If button is stuck call dealer for repair Bed Hi Lo movement does not stop Check cables If damaged call dealer Invacare IVC Model BAR600IVC Bariatric Bed 50 Part No 1123842 10 TROUBLESHOOTING 10 2 Troubleshooting Mechanical SYMPTOM PROBABLE CAUSE SOLUTIONS Bed does not stay in place Locking casters not locked Lock casters Refer to Installing Casters on page 35 Bed sections do not move Pull tube Ensure pull tubes are properly connected Refer to FIGURE 11 Check pull tube s for binding Call dealer for repairs Bed ends move in opposite directions Drive shaft connected to wrong gear Reinstall drive shaft Refer to Assembling Installing Removing electrical or manual bed box shaft Drive Shaft on page 40 Hi Lo function does not work Drive shaft disconnected Reinstall drive shaft Refer to Assembling Installing Removing Drive Shaft on
23. ling Removing Drive Shaft For this procedure refer to FIGURE 9 and FIGURE 10 on page 43 Reverse this procedure to remove the drive shaft The drive shaft for the Hi Lo function consists of two sections that are shipped unassembled The inner shaft has a positioning spring button and the outer shaft has three positioning holes one storage position hole and a telescoping end 1 Remove the plastic caps from each end of the drive shaft 2 Press the spring button on the inner shaft and insert the inner shaft into the outer shaft 3 Engage the spring button into the third positioning hole Refer to FIGURE 9 A common gear box is used on both bed ends The bottom output shaft is used at the head end and the top output shaft is used at the foot end of the bed Before assembling the bed ensure the drive shaft cover of both gear boxes are in the correct position up for the head end and down for the foot end Refer to FIGURE 10 4 Attach the inner shaft to the bottom gear box output shaft on the head end of the bed 5 Push in on the spring loaded end of the drive shaft and attach to the Hi Lo motor output shaft facing the head end of the bed Invacare IVC Model BAR600IVC Bariatric Bed 40 Part No 1123842 8 PACKAGING HANDLING AND SET UP Head End End Head End Gear Box End Box Drive Shaft Under Side Center of Bed Positioning Holes Inner
24. low the protection function time to reset and restore bed function Depending on severity of the initial overheating this could take up to 30 minutes The emergency crank MUST be removed before the bed is used Failure to remove the crank may cause damage or personal injury Part No 1123842 17 Invacare Model BAR600IVC Bariatric Bed 4 OPERATION AND ADJUSTMENT 4 Operation and Adjustment 4 Operating Bariatric Bed WARNING NEVER operate if the unit has a damaged cord or plug If it is not working properly call a qualified technician for examination and repair Keep all electrical cords away from heated or hot surfaces Ensure all cables and cords are routed such that they will not become entangled or pinched Otherwise damage or injury may result DO NOT place pendant under or between objects This may unintentionally press the buttons and may cause injury or damage to occur Operating Bariatric Bed Before placing the bed into use test it by operating it through all phases of its operation l If any problems arise during the test recheck all electrical connections and mechanical hook ups 2 Asix function pendant is used for all bed operations An emergency crank allows operation in the event of a power outage FIGURE Operating Bariatric Bed Invacare IVC Model BAR600IVC Bariatric Bed 18 Part No 1123842 4 OPERATION AND ADJUSTMENT Raising and Lowering Head UP Head DOWN Entire Bed B
25. nches 55 cm 2 inches BED OVERALL LENGTH 88 inches 223 5 cm WIDTH 42 inches 106 7 cm SPLIT SPRINGS TO ENDS HEAD 43 inches 109 2 cm FOOT 45 inches 114 3 cm SHIPPING WEIGHT 275 Ibs WEIGHT LIMITATION 700 Ibs Including accessories matress occupant and any other objects positioned on the bed NOTE Height from floor to bed deck 2 3 Bed Components Head spring with one motor BAR5000IVC Foot spring with two motors BAR5490IVC Ends BAR530IIVC Part No 1123842 9 Invacare Model BAR600IVC Bariatric Bed 3 SAFETY 3 Safety 3 1 General Guidelines WARNING Do not use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner s manuals service manuals or instruction sheets supplied with this product or optional equipment If you are unable to understand the warnings cautions or instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur The initial set up of this bed must be performed by a qualified technician Procedures other than those described in this manual must be performed by a qualified technician For Dealers Only Set up and Assembly Instructions are in the rear of this manual These procedures must be performed by a qualified technician
26. nction does not work Drive shaft disconnected Call dealer Pressing function on pendant results in motion Motor cable connections to junction Call dealer other than that intended box incorrect Part No 1123842 25 Invacare Model BAR600IVC Bariatric Bed 7 ASSEMBLY MAINTENANCE AND ADJUSTMENT SECTIONS FOR DEALERS ONLY 7 Assembly Maintenance and Adjustment Sections For Dealers Only A WARNING The procedures in the following sections MUST be performed by a qualified technician 7 Overview of Procedures Receiving Unpacking Unpacking the Bed Ends Unpacking Foot and Head Spring Sections Inspecting Set Up Assembling and Disassembling the Head and Foot Spring Sections Installing Removing Bed Ends Connecting Crossover Cable Refer to Set Up Connecting Crossover Cable on page 37 m Q Installing Casters Q Assembling Installing Removing the Drive Shaft Q Inspecting the Bed Storing Invacare IVC Model BAR600IVC Bariatric Bed 26 Part No 1123842 8 PACKAGING HANDLING AND SET UP 8 Packaging Handling and Set Up 8 1 Receiving l Count cartons before signing shipping papers 2 Designate someone at the facility to receive and inspect all merchandise Use the master order acknowledgment to check off items as they are received 3 Compare the number of cartons shipped with the number of cartons actually received and note such on the consignee copy of the freight bill Make sure to have
27. nto the corner locks on the bed end 3 Tilt the bed end toward the head section and place the corner plate head rivets into the corner locks 4 Return the bed end to its full upright position The corner plate head rivets will lock into place 5 Repeat STEPS 1 4 to install the remaining bed end to the foot spring section 6 If necessary install the casters Refer to Installing Casters on page 35 Bed E Corner Plate Corner Plate Head Section Corner Locks Corner Locks FIGURE 5 Installing Removing Bed Ends Invacare Model BAR600IVC Bariatric Bed 34 Bed E Part No 1123842 8 PACKAGING HANDLING AND SET UP Installing Casters WARNING Ensure that the locking casters are installed diagonally from each other and are locked Otherwise damage or personal injury could occur The proper casters are provided with the Bariatric Bed DO NOT use any other casters with the Bariatric Bed Otherwise damage or personal injury could occur Ensure that casters are locked and that the bed does not move before transferring DO NOT transfer occupant if bed is not stable For this procedure refer to FIGURE 6 on page 36 ALWAYS locate locking caster in the same location on each bed end so that they will always be assembled diagonally opposite each other when inventory is mixed Position the two locking casters so that they will be diagonally opposite from one another when the bed is assembled If two locking casters
28. ord away from heated surfaces DO NOT use outdoors Use masked or nasal type oxygen administering equipment only in conjunction with the manual electric bed The use of ANY other type of oxygen administering equipment can result in a fire hazard To disconnect DO NOT depress pendant buttons Risk of electric shock Connect this bed to a properly grounded outlet only Refer to Grounding Instructions on page 16 10 Risk of injury to persons DO NOT place video equipment such as televisions or computer monitors bed Part No 1123842 SAVE THESE INSTRUCTIONS II Invacare Model BAR600IVC Bariatric Bed 3 SAFETY Operating Information WARNING Check all parts for shipping damage and test before using In case of damage DO NOT use Contact a qualified technician for further instruction After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Close supervision is necessary when the manual electric bed is used by or near children and physically challenged individuals DO NOT let any individual underneath the bed or in between the raised bed frame components at anytime When bed is not to be used for an extended period unplug electric bed from the wall outlet Keep the product a minimum of 12 inches away from any direct heat source DO NOT unplug power cord from junction box If a liquid is spilled in or around the electric bed unplug the electric bed b
29. page 40 Pressing function on pendant results in Motor cable connections to junction Verify connections Refer to FIGURE 11 motion other than that intended box incorrect Part No 1123842 5l Invacare Model BAR600IVC Bariatric Bed Invacare Corporation USA Canada One Invacare Way 570 Matheson Blvd E Elyria Ohio USA Unit 8 44036 2125 Mississauga Ontario 800 333 6900 L4Z 4G4 Canada 800 668 5324 www invacare com Part No 1123842 Rev H 4 11 Yes can
30. products using electric cords which may get tangled around the bed side rails or legs during operation of the electric bed The electric bed is equipped with locking casters When transferring into or out of the electric bed ALWAYS lock the locking caster s Inspect the wheel locks for correct locking action before actual use Even with casters properly locked some flooring surfaces such as tile or wood will allow the bed to move under some conditions Use on surfaces such as these must be evaluated by the care provider Entrapment Warning WARNING Refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com for additional safety information Mattress MUST fit bed frame and bed rails snugly to reduce the risk of entrapment After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Part No 1123842 13 Invacare Model BAR600IVC Bariatric Bed 3 SAFETY Replacement Parts Accessories WARNING Use masked or nasal type oxygen administering equipment only in conjunction with the manual electric bed The use of any other type of oxygen administering equipment can result in a fire hazard When using nasal or masked type oxygen administering equipment the oxygen or air tubing MUST be routed and secured properly to ensure that the tubing does not become entangled and or severed during normal operation of manual electric bed ALWAYS test to make sure that the side rails
31. r cable plug in crossover cable See caution label in Detail in FIGURE 11 4 Before placing bed into use test the bed by operating it through all phases of operation Invacare IVC Model BAR600IVC Bariatric Bed 44 Part No 1123842 8 PACKAGING HANDLING AND SET UP JUNCTION BOX CONNECTOR IDENTIFICATION DETAIL CAUTION Pull Tube cable connections MUST be aligned properly Align locking levers with locking tabs for proper connection Mis alignment of cable P ower connections will cause permanent product damage Be Locking Lever Locking Tab Head Motor Crossover Cable Cable P N 1171770 Rev A Pendant and Cord Pendant Cord Hi Lo Motor _ Conector Connector Full Electric Junction Box Power Cord Connector Head Motor Connector Foot Motor Connector FIGURE 11 Inspecting the Bed 8 5 Storing the Beds WARNING DO NOT place other objects on top of the cartons If bed is not being assembled immediately retain the cartons and packaging for storage until ready for assembly Store the Invacare homecare bed in a dry area Part No 1123842 45 Invacare Model BAR600IVC Bariatric Bed 9 MAINTENANCE 9 MAINTENANCE 9 Washing Bed Ends A CAUTION DO NOT wash head or foot section AC motors and electronics are not water proof For this procedure refer to FIGURE 1 Stand or prop each bed end in an upright position on i
32. r conductors Signs of pinching or crushing Broken or deformed connectors If these conditions are present the bed MUST not be used until the damaged component wiring is replaced Modification or other forms or repair including electrical or similar tape MUST NEVER be used Invacare IVC Model BAR600IVC Bariatric Bed 48 Part No 1123842 9 MAINTENANCE Pass Fail PASS Bed and all components have passed all of the above inspection criteria and the bed is ready for placement into a client s home FAIL Bed or any component has failed any of the above inspection criteria Tag the bed or component with a complete description of the failure s and have the bed serviced 1123842 49 Invacare Model BAR600IVC Bariatric Bed 10 TROUBLESHOOTING 10 Troubleshooting A WARNING Read all general guidelines warnings and cautions before performing any repair maintenance on the bed All repair and maintenance on the bed should be performed by a qualified technician 10 1 Troubleshooting Electrical SYMPTOM Bed section does not move PROBABLE CAUSE End of stroke reached SOLUTIONS Operate opposite button Full Electric Bed Hi Lo function does not work Bed not plugged in Ensure power cord is plugged into power source Pendant not functioning Ensure Pendant correctly connected to junction box Refer to FIGURE 11 Ensure Pendant cable is not entangled pinched Cab
33. r connection Mis alignment of cable connections will cause permanent product damage Locking Lever Locking Tab Head Motor Cable Crossover Cable P N 1171770 Rev A FIGURE 7 Connecting Crossover Cable Invacare IVC Model BAR600IVC Bariatric Bed 38 Part No 1123842 8 PACKAGING HANDLING AND SET UP Loops Hidden by MT LONG CROSSOVER CABLE otor Guar Motor Guard Motor Guards Side Channel Slack in gre 4 Crossover P Cable Bottom View of Bed Junction Box Connection d of Crossover L to Head zum 4 Actuator m NS j 5 d i Sg Foot End of Bed H Head Actuator 4 amp ei loj ai EEN Ic em Se CAUTION H ead End of Bed All cable connections MUST be aligned properly Align locking levers with locking tabs for proper connection Mis alignment of cable connections will cause permanent product damage Locking Lever Locking Tab Head Motor Crossover Cable Cable P N 1171770 Rev A FIGURE 8 Connecting Crossover Cable Part No 1123842 39 Invacare Model BAR600IVC Bariatric Bed 8 PACKAGING HANDLING AND SET UP Assembling Instal
34. s only ACCESSORIES WARNINGS Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case of damage DO NOT use Contact Invacare Carrier for further instruction Invacare IVC Model BAR600IVC Bariatric Bed 10 Part No 1123842 3 SAFETY IMPORTANT SAFETY INSTRUCTIONS When using the bed basic precautions should always be followed including the following Read all the instructions before using the bed DANGER To reduce the risk of electric shock Always unplug the bed from the electrical outlet before cleaning WARNING To reduce the risk of burns fire electric shock or injury to persons 2 3 Unplug from the outlet before servicing Close supervision is necessary when the bed is used by or near children and or disabled persons Use this bed only for its intended use as described in these instructions DO NOT use attachments not recommended by the manufacturer NEVER operate this bed if it has a damaged cord or plug if it is not working properly if it has been dropped damaged or dropped into water Return the bed to a service center for examination and repair Keep the c
35. sed to be free from defects in materials and workmanship for a period of one year from date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty Invacare warrants all welds of this product when purchased new and unused to be free from defects in materials and workmanship for a period of five years from date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty If within such warranty periods any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the back cover provide dealer s name address and the date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PR
36. table communications equipment in the area around such equipment If RFI causes erratic behavior unplug the electric bed immediately Leave unplugged while transmission is in progress Weight Limitations WARNING The total weight limit of the Bariatric Bed including accessories mattress occupant and any other objects positioned on the bed is 700 pounds 318 kg 600 pounds 272 kg patient weight NEVER permit more than one person on the manual electric bed at any time Body weight should be evenly distributed over the surface of the manual electric bed DO NOT lay sit or lean in such a way that your entire body weight is placed only on raised head or foot sections of the bed This includes when repositioning or transferring in or out of bed Invacare Model BAR600IVC Bariatric Bed 16 Part No 1123842 3 SAFETY Pendant Operation A WARNING A safety feature of this product includes protection against overheating caused by excessive or extended periods of operation Depending on the duration this includes multiple or repeated adjustments or the use of multiple functions at one time To ensure trouble free operation ALWAYS allow a slight pause between multiple adjustments and avoid pressing more than one function button at a time If thermal protection activation should occur the bed will not respond to pendant commands Given this situation release the pendant button and allow the bed unit to sit for several minutes This will al
37. ts legs 2 Using a mild soap detergent and soft bristle brush or sponge scrub all exterior surfaces 3 Using a hose and nozzle attachment rinse bed ends thoroughly with plain cold or warm water DO NOT exceed a water temperature of 10 F Use household tap pressure DO NOT use pressure washers or steam cleaners A CAUTION To protect flooring ensure bed ends are completely drained and dry before placing on flooring Otherwise remaining dirty water may damage or stain flooring Avoid spraying water directly into the gear box ends Otherwise damage to the gear box may occur Tip bed end from side to side to allow any collected or trapped water to drain 5 Thoroughly towel dry bed end and all components 6 Repeat drying process until all components are dry For this procedure refer to FIGURE 1 Ensure that the bed end is completely dry before storing Invacare IVC Model BAR600IVC Bariatric Bed 46 Part No 1123842 9 MAINTENANCE End Gear Box 0 FIGURE Washing Bed Ends 9 2 Cleaning Head and Foot Sections l Unplug the power cord of electric beds before performing maintenance 2 Wipe down the bed with disinfectant Allow it to dry completely 9 3 Maintenance Checklist Invacare recommends the following maintenance and cleaning procedures be conducted between users or as needed This form is provided as a guide to help with documentation Mechanical Inspection and Maintenance Inspect
38. unplug the power cord from the junction box Damage to cord will result CAUTION cable connections MUST be aligned properly Align locking levers with locking tabs for proper connection Mis alignment of cable connections will cause permanent product damage Part No 1123842 15 Invacare Model BAR600IVC Bariatric Bed 3 SAFETY Grounding Instructions A WARNING Electric beds are equipped with three prong grounding plugs for protection against possible shock hazards Where a two prong wall receptacle is encountered it is the personal responsibility and obligation of the customer to contact a qualified electrician and have the two prong receptacle replaced with a properly grounded three prong wall receptacle in accordance with the National Electrical Code If you must use an extension cord use only a three wire extension cord having the same or higher electrical rating as the device being connected DO NOT under any circumstances cut or remove the round grounding prong from any plug used with or for Invacare products In addition Invacare has placed RED warning tags on some equipment DO NOT remove these tags For proper grounding junction box MUST be securely connected to the bed with metal screws and the spacer provided or electrical shock could occur Radio Frequency Interference A WARNING Electronic equipment may be influenced by Radio Frequency Interference RFI Caution should be exercised with regard to the use of por
39. utton Button To raise the entire bed press the Bed UP button 2 lower entire bed press the Bed DOWN button Bed UP Bed DOWN Button Button Head and Foot Sections l Toraise the head of the bed press the Head UP button 2 Tolower the head of the bed press the Head DOWN button Foot UP Foot DOWN 3 raise the foot of the bed press the Foot UP button Button Button 4 lower the foot of the bed press the Foot DOWN button FIGURE 2 Raising and Lowering 42 Emergency Crank For this procedure refer to FIGURE 3 If the bariatric bed must be adjusted manually due to a power outage or an electronic malfunction use the emergency crank to make the adjustments Under the bed locate the exposed shaft end according to the function you want to perform 2 Attach the emergency crank to the motor shaft end of the head section or the motor shaft end of the foot section 3 Crank clockwise or counterclockwise to adjust the bed Push in the emergency crank while turning it the desired direction 4 Remove the emergency crank Part No 1123842 19 Invacare Model BAR600IVC Bariatric Bed 4 OPERATION AND ADJUSTMENT A WARNING The emergency crank MUST be removed before the bed is used Failure to remove the crank may cause damage or personal injury Bottom of bed shown Head Section Foot Section Emergency Crank Ce LC mmy H ES Ki n Ki
40. y the bed frame manufacturer are not interchangeable Variations in bed side rail design width and thickness or firmness of the mattress could cause contribute to entrapment Invacare IVC Model BAR600IVC Bariatric Bed 14 Part No 1123842 Electrical 3 SAFETY DANGER When using an extension cord use only a three wire extension cord having at least 16 AWG American Wire Gauge wire and the same or higher electrical rating as the device being connected Use of improper extension cord could result in a risk of fire and electric shock Three prong to two prong adapters should not be used Use of three prong adapters can result in improper grounding and present a shock hazard to the user WARNING NEVER operate if the unit has a damaged cord or plug If it is not working properly call a qualified technician for examination and repair Keep all electrical cords away from heated or hot surfaces Ensure all cables and cords are routed such that they will not become entangled or pinched Otherwise damage or injury may result Repair or Service Information WARNING DO NOT open assemblies such as the motors pendant junction boxes or gear boxes No user serviceable parts are inside Only qualified technicians are permitted to repair these parts If unqualified individuals perform any work on these beds the warranty is void Unplug the power cord from its power source before performing any maintenance on the electric bed DO NOT
Download Pdf Manuals
Related Search