iPR-8 proximity reader User manual
Contents
1. auses beyond the control of Integrated Technical Vision Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be lieu of any and all other warranties whether expressed or implied and of all other obligations or liabilities on the part of Integrated Technical Vision Ltd This warranty contains the entire warranty Integrated Technical Vision Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any warranty or liability concerning this product In no event shall Integrated Technical Vision Ltd be liable for any direct indirect or consequential damages Loss of anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product 101203 4 Integrated Technical Vision Ltd http www itvsystems com ua2. boot 2 Integrated Technical Vision Ltd http www itvsystems com ua The Reader Operation Reading of identificator code The code reading is annunciated by built in buzzer and two color LED according to interface type and annunciation mode refer to Data transfer and Annunciation Repeated reading will be available after 0 8 sec if the identificator is moved away from the reader sensing area Hold Mode Reader is turned to the hold mode while yellow wire is closed to the ground In this mode reader does not read cards thus current consumption decreases to 25mA Do not apply voltage to hold outlet Data transfer and Annunciation The reader is provided with two color LED and built in buzzer LED and buzzer function according to interface type programmed and annunciation mode Wiegand or TouchMemory Interface Engaging of LED and buzzer is possible automatically or by closing of corresponding wire to the black wire GND according to Table 2 Table 2 Annunciation mode 00 Beep on card read Outside control Beep on card read Outside control Beep on card read a Outside control 06 __ Beep on card read 07__ Outside control a Beep oD card read Normally ON switched OFF at reading Blinks at reading Availability to switch P p Availability to switch ON from outside Availability to switch OFF from outside ON from outside Data transmissions from reader comply with the standard specified Protocol for TouchMemory int
3. enled Greenled E E E a Yelow Hold Hod Hod Multiwire signal cable with 0 22 mm wires cross sectional is recommended to connect the reader and control panel Using this cable the maximum length of 150 meters can be obtained Type of interfaces The proximity reader is intended to be applied in different access control systems using RS232 Wiegand 26 Wiegand 37 Wiegand 42 or TouchMemory interface Mounting It is recommended to mount the reader on a wall closely to a door at appropriate height Do not mount the reader on metal surfaces since it causes decreasing of reading distance If more than one reader is used in the system place them not closer than 50 cm one from another otherwise a reading distance will be decreased To avoide decrease of reading distance connect yellow colored wires of readers To mount the reader preceed as follows Remove the boot in the bottom part of the reader Loosen the screw i Put on Push mounting panel towards the screw and and remove it from the reader push Using the mounting panel as a template mark and then drill two openings 6mm in diameter and 35mm deep Pass the wire through central opening Secure the mounting plate on a wall using plastic nailing plugs and screws Connect the reader to the control panel s cable Puton the reader on the mounting plate push the case down against stop and secure the reader with the screw Put on the
4. erface from family 01 to satisfy the requirements DS1990 RS232 interface To control annunciation send three byte control packet to the reader Packets should be transmitted with 2 400 bits per second 8 bit data no parity 1 stop bit Packet format byte 2 green green buzzer buzzer stedy blinks pulsatory uninterruptedly 1 corresponds to LED or buzzer switching on LED blinking and buzzer pulsatory control bits have the highest priority Annunciation does not change until next control packet is received http www itvsystems com ua Integrated Technical Vision Ltd 3 Reader transmits data as follows we J o oo 2 ODR data bt 7 Lo st 4 stat 1f o Berain LoL ols fx x x px Checksum exclusive OR of low nibbles of bytes from 1 to 10 high nibble of always must be 3h Example Card code 7EQ00460AA will be sent as 23h 37h 3Eh 30h 30h 30h 34h 36h 30h 3Ah 3Ah 3Bh ODh Limited Warranty Integrated Technical Vision Ltd warrants that for a period of eighteen months from the date of purchase the product shall be free of defect in materials and workmanship under normal use and that in fulfilment of any breach of such warranty Integrated Technical Vision Itd shall at its option repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and not damages incurred in shipping or handing or damages due to c
5. iPR 8 proximity reader Usermanual Function iPR 8 proximity reader is intended to be applied in different ac cess control systems using RS232 Wiegand 26 Wiegand 37 Wiegand 42 or TouchMemory interface Types of identificators Integrated Technical Vision Itd manufactures readers operating with amplitude modulation ASK proximity cards and tags Design The reader is placed in miniature hermetic plastic case Thanks to the small overall dimensions the reader is distinguished for its advanced reliability Specifications Warm up time 10 seconds after power start Case Material ABS plastic Dimensions 154 x 45 x 22mm Weight 94 gramm Ambient Conditions Temperature 35 60 C Humidity 100 without condensate Power supply Voltage 9 16 V of direct current Current up to 50 mA Maximal current up to 80 mA Voltage ripple upto 500 mV Distance of reading Typical reading distance is 105 200 mm and depends on tag type used with it This parameter is valid for power supply voltage range from 9 to 16 VDC and ripple up to 150 mV P P http www itvsystems com ua Integrated Technical Vision Ltd 1 Wiring Reader has 8 wire colored cable intended for connection to access control panel Table 1 The wires assignment Jw 1 W3 W4 WS RS232 TouchMemory DC B053 Function Green Datao Rx iButton B Wie oa o _ ae ee Black GND GND GND D Brown Redled Redled Orange Gre
Download Pdf Manuals
Related Search