Home

2002 Excursion - Hiller Ford Inc.

1. If the light does not come on or if the light flashes steadily have your vehicle serviced as soon as possible damage to the transmission could occur Turn signals Iluminates when the turn signals or yo Sy the hazard lights are turned on If the lights stay on continuously or flash faster check for a burned out bulb High beams Illuminates when the high beam headlamps are turned on D 13 Instrument Cluster Door ajar Illuminates when any door is open C or not fully closed Fh JV_ IS SJ SecuriLock anti theft system Illuminates when the anti theft alarm system is armed If the light THEFT fails to illuminate continues to flash or remains on have the system serviced Refer to SecuriLock passive anti theft system in the Locks and Security chapter Four wheel drive indicator Illuminates when the four wheel 4x4 drive is engaged If the light continues to flash have the system serviced Four wheel drive low Illuminates when four wheel drive LOW low is engaged If the light continues to flash have the system serviced RANGE Safety belt warning chime A Sounds to remind you to fasten your safety belts BeltMinder chime A Sounds intermittently to remind you to fasten your safety belts Supplemental restraint system SRS warning chime amp Sounds when a malfunction in the supplemental restraint system front or side airbags has been detected Have the supplemental restraint syste
2. 0006 231 lubrication specifications 0 0 0 263 265 refill capacities c ee 260 SETVICE PONS 2 sce cescweveuvecaedecess 226 starting after a collision 190 Engine block heater 0 0 0 0 159 Engine oil sesseesssisesressceieasiacieare 228 checking and adding 228 GIDSLICK ariennir 228 filter specifications 230 260 recommendations ccce 230 refill capacities eserse 260 specifications 0 0 0 263 265 Exhaust fumes ccceceeeeeee 159 F Fail safe cooling c eeeee 238 Fluid capacities eee 260 POSIBTADS nena aa 73 Four Wheel Drive VENICIES seisein 14 170 description oo eee eeeeeeeeeeeeeees 171 driving off road eee 173 electronic shift 170 171 indicator light 0 14 171 preparing to drive your Vehicle ceredssesicssalxseacesaxasssedixerss 164 PUG aririk 239 calculating fuel economy 243 CAD eeren EEEE EREN 11 241 CADACILY cave sayadcdeitetandeabadeacsecees 260 choosing the right fuel 242 comparisons with EPA fuel economy estimates 006 246 detergent in fuel 0 243 filling your vehicle with fuel 0000 239 241 244 274 filter specifications 243 260 fuel pump shut off switch 190 GAUGE nosse haara tnana 17 improving fuel economy 243 low fuel warning light 13 octane rating 242 265 266 GUAY a2 ssnissecscsdssscssseesces
3. 6 To exit the zone setting mode and save the displayed zone in memory release both controls for greater than five seconds Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines For optimum calibration turn off all electrical accessories heater air conditioning wipers etc and make sure all vehicle doors are shut 1 Locate the trip computer located in the overhead console 2 Start the vehicle 98 Driver Controls 3 Press and hold both trip computer controls After approximately eight seconds the trip computer will enter CAL mode CAL mode is indicated when the display lights the CAL indicator RESET 4 Release both controls The display will return to normal except that the CAL indicator will remain lit until the compass is sucessfully calibrated 5 Slowly drive the vehicle in a circle less than 5 km h 8 mph until the CAL indicator turns off It may take up to five circles to complete calibration 6 The compass is now calibrated HOMELINK UNIVERSAL TRANSCEIVER IF EQUIPPED The HomeLink Universal Transceiver located on the driver s visor provides a convenient way to replace up to three hand held transmitters with a single built in device This feature will learn the radio frequency codes of most current transmitters to operate garage doors entry gate operators security systems entry door
4. CO Noted CC pte CO Notused CC 301 Front blower motor relay 302 _ Powertrain BEC relay 303 Injector driver module relay Diesel only 304 Heated backlite relay 305 Trailer tow battery charge relay 306 Delayed accessory relay Cd 3807 CO Starter relay ooo y CHANGING THE TIRES If you get a flat tire while driving do not apply the brake heavily Instead gradually decrease your speed Hold the steering wheel firmly and slowly move to a safe place on the side of the road The use of tire sealants is not recommended and may compromise the integrity of your tires The use of tire sealants may also affect your tire pressure monitoring system if equipped Spare tire information Your vehicle may be equipped with a spare tire that can be used as either a spare or a regular tire The spare tire is not equipped with wheel trim The wheel trim from the original wheel tire may be used on the spare Your vehicle is equipped with 4WD a spare tire of a different size than the road tires should not be used Such a tire could result in damage to driveline components and make the vehicle difficult to control 196 Roadside Emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations Spare tire Mounted on the left rear quarter panel in the cargo area In the right rear cargo area stowage bin Jack han
5. e Maximum Trailer Weight Rating Maximum weight of a trailer the vehicle is permitted to tow The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine transmission combination any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle e Maximum Trailer Weight Maximum weight of a trailer the loaded vehicle Gncluding occupants and cargo is permitted to tow It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle e Trailer Weight Range Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating Remember to figure in the tongue load of your loaded trailer when figuring the total weight Do not exceed the GVWR or the GAWR specified on the certification label Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle s GVWR and GAWR limitations Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations The Safety Certification Label found on the driver s door pillar lists several important vehicle weight rating limitations Before adding any additional equipment refer to these limitations If you are adding weight to the front of your vehicle potentially including weight added to the cab the weight added sho
6. l ll l iad Replacing the tires Replace the tires when the wear band is visible through the tire treads When replacing full size tires never mix radial bias belted or bias type tires Use only the tire sizes that are listed on the Certification Label Make sure that all tires are the same size speed rating and load carrying capacity Use only the tire combinations recommended on the label If you do not follow these precautions your vehicle may not drive properly and safely Make sure that all replacement tires are of the same size type load carrying capacity and tread design e g All Terrain Touring etc as originally offered by Ford 258 Maintenance and Specifications Do not replace your tires with high performance tires or larger size tires Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over Tires that are larger or smaller than your vehicle s original tires may also affect the accuracy of your speedometer SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains If you need to use chains it is recommended that steel wheels of the same size and specifications be
7. Terrain Hills mountains and tall buildings between your vehicle s antenna and the radio station signal can cause FM reception problems Static can be caused on AM stations by power lines electric fences traffic lights and thunderstorms Moving away from an interfering structure out of its shadow returns your reception to normal e Station overload Weak signals are sometimes captured by stronger signals when you pass a broadcast tower A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo AUDIO SYSTEM WARRANTIES AND SERVICE Refer to the Warranty Guide for audio system warranty information If service is necessary see your dealer or a qualified technician 58 Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM Fan speed control 8 Controls the volume of air circulated C in the vehicle C Temperature control knob Controls the temperature of the airflow inside the vehicle Mode Selector Control Controls the direction of the airflow y E gi to the inside of the vehicle ps i B w The air conditioning compressor can operate in all modes except Ji and A However the air conditioning will only function if the outside temperature is about 6 C 43 F or higher Since the air conditioner
8. s door with a key or by using the lock button on the remote entry transmitter if equipped 108 Locks and Security Childproof door locks When these locks are set the rear doors cannot be opened from the inside The rear doors can be J opened from the outside when the doors are unlocked The childproof locks are located on O rear edge of each rear door and E must be set separately for each g door Setting the lock for one door will not automatically set the lock for both doors Move lock control up to engage the childproof lock Move control down to disengage childproof locks 00 o j e activate the panic alarm The remote entry LOCK and UNLOCK operate with the ignition in the ON or OFF position and the transmission in P Park REMOTE ENTRY SYSTEM The remote entry system allows you to e unlock all vehicle doors without a key e lock all vehicle doors without a key If there is any potential remote keyless entry problem with your vehicle ensure ALL remote entry transmitters are brought to the dealership to aid in troubleshooting This device complies with part 15 of the FCC rules and with RS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 109 Locks and Security Changes or modifications
9. you need to keep these objects from touching the coded key while starting the engine These objects and devices cannot damage the coded key but can cause a momentary no start condition if they are too close to the key during engine start If a problem occurs turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key Check to make sure the coded key is an approved Ford coded key If your keys are lost or stolen you will need to do the following e Use your spare key to start the Be vehicle or Af e Have your vehicle towed to a dealership or a locksmith The key codes will need to be erased from your vehicle and new key codes will need to be re coded Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience The correct coded key must be used for your vehicle The use of the wrong type of coded key may lead to a no start condition If an unprogrammed key is used in the ignition it will cause a no start condition Programming spare keys A maximum of eight keys can be coded to your vehicle Only SecuriLock keys can be used To program a coded key yourself you will need two previously programmed coded keys Keys that already 118 Locks and Security operate your vehicle s engine and the new unprogrammed key s readily accessible for tim
10. 2 270 kg 5 000 lb trailer weight and 227 kg 500 lb tongue weight capacity If it is necessary to relocate the trailer hitch ball position a frame mounted trailer hitch must be installed Driving while you tow When towing a trailer e Ensure that you turn off your speed control The speed control may shut off automatically when you are towing on long steep grades e Consult your local motor vehicle speed regulations for towing a trailer 186 Driving e To eliminate excessive shifting when towing on long steep grades use a lower gear This will also assist in transmission cooling When the terrain becomes flatter put your transmission back into overdrive for the best fuel economy e Anticipate stops and brake gradually Do not exceed the GCWR rating or transmission damage may occur Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent service intervals Refer to your scheduled maintenance guide for more information Trailer towing tips e Practice turning stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination When turning make wider turns so the trailer wheels will clear curbs and other obstacles e Allow more distance for stopping with a trailer attached e The trailer tongue weight should be no more than 10 15 of the loaded trailer weight e After you have traveled 80 km 50 miles thoroughly check your hit
11. 260 fluid specifications 263 265 lubricant specifications 263 265 DALIAN nsiro asieran 162 pedals see Power adjustable foot pedals cccceseeeeeseees 90 shift interlock svresesiiriasz 164 Break in period cccccescceesnees 5 BUDS 4 tectssanssss vais tencvscestexedeacicossan 76 C Capacities for refilling fluids 260 Cargo MObircssscesecadonnsveassbessceeesstere 105 CD 6 iSC seseriai sinsi 28 CD single premium s s 19 Certification Label 0 267 Changing a tite erssniosiess 196 Child safety restraints 148 child safety belts oo 148 Child safety seats e 149 attaching with tether straps 153 ifi front seat axessatecdaecisescredsaeess 151 IN LEAT Set eoria 151 Cleaning your vehicle engine compartment 219 EXtETIOT scgciiesssesreducceebesseiaesnees 222 instrument panel 008 221 MILTON ronn e e 222 pPlagtie DAIS cogssrseorsenrersenis 220 WASHING kepere enereeikeie ms 218 WOKING seporete a Rai 218 WHEECIS aeea na 219 wiper blades 0006 220 221 woodtone trim 0 221 Climate control see Air conditioning or Heating 59 62 CLOCK retra ats 24 32 Compass electronic 88 97 calibration woo ceeceeeeeceeeeseeeeees 98 set zone adjustment 98 CONSOLE ooo eeeccceeesseeeeseseeeeseeees 104 overhead ceeeccseeeesseeeeeee 84 85 Controls POWEYL SAt eeeeeeseeceeeeeeseeeeee 122 s
12. CLEANING CASSETTE PLAYER IF EQUIPPED Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation CASSETTE AND CASSETTE PLAYER CARE e Use only cassettes that are 90 minutes long or less e Do not expose tapes to direct sunlight high humidity extreme heat or extreme cold Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing e Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub 57 Entertainment Systems e Remove loose labels before inserting tapes e Do not leave tapes in the cassette player for a long time when not being played RADIO FREQUENCY INFORMATION The Federal Communications Commission FCC and the Canadian Radio and Telecommunications Commission CRTC establish the frequencies AM and FM stations may use for their broadcasts Allowable frequencies are AM 530 540 1600 1610 kHz FM 87 7 87 9 107 7 107 9 MHz Not all frequencies are used in a given area RADIO RECEPTION FACTORS Three factors can affect radio reception e Distance strength The further an FM signal travels the weaker it is The listenable range of the average FM station is approximately 40 km 24 miles This range can be affected by signal modulation Signal modulation is a process radio stations use to increase their strength volume relative to other stations
13. chart Gn the Trailer Towing section to find the maximum GCWR for your type engine and rear axle ratio 2 Weigh your vehicle as you customarily operate the vehicle without cargo To obtain correct weights try taking your vehicle to a shipping company or an inspection station for trucks 3 Subtract your loaded vehicle weight from the maximum GCWR on the following charts This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart 183 Driving TRAILER TOWING Your vehicle may tow a Conventional Class IV trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts Your vehicle s load capacity is designated by weight not by volume so you cannot necessarily use all available space when loading a vehicle Towing a trailer places an additional load on your vehicle s engine transmission axle brakes tires and suspension Inspect these components carefully after any towing operation The following trailer towing charts apply to vehicles equipped with gasoline engines for Diesel engines refer to the 7 3 Liter Power Stroke Direct Injection Turbo Diesel Supplement The hitch receiver was designed not to be removed Any modification or removal of the hitch receiver compromises the safety benefit it was designed to provide 4x2 w automatic transmissio
14. muting the speakers will not mute the headphones 41 Entertainment Systems USING HEADPHONES PERSONAL AUDIO SYSTEM The Personal Audio System allows VOLUME MEDIA MEM lt lt SEEK amp the rear seat passengers to listen to COO QO O COO one media source radio tape CD ate or CD changer if equipped while gt Q Os a the front seat passengers listen to z another However front and rear seat passengers can not listen to two different radio stations simultaneously Plug a 3 5 mm headphone not included into either one of the two A jacks Press the A q control to operate the headphones The rear speakers will cut out once the speaker on off control is pressed A soft audible sound may be heard from the rear speakers The front speaker will remain playing for the front passengers Press the A 4 control again to deactivate the headphones Personal Audio System MEDIA SELECT Push the MEDIA control to toggle between AM FM1 FM2 tape CD or CD changer if equipped VOLUME MEDIA MEM lt SEEK COO O CO Oo a MEMORY PRESET CONTROL Push the MEM control successively to allow rear seat passengers to scroll through the six memory VOLUME MEDIA MEM 4 SEEK gt presets in AM FM1 or FM2 OO CO Push the MEM control in CD OC O a changer mode if equipped to advance to the next disc SEEK FUNCTION e Press lt Q to find the next K m listenable station dow
15. operated for an extended period at high speeds in city traffic during hot weather or pulling a trailer the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking 1 Drive the vehicle 30 km 20 miles or until it reaches normal operating temperature 2 Park the vehicle on a level surface and engage the parking brake 3 With the parking brake engaged and your foot on the brake pedal start the engine and move the gearshift lever through all of the gear ranges Allow sufficient time for each gear to engage 4 Latch the gearshift lever in P Park and leave the engine running 5 Remove the dipstick wiping it clean with a clean dry lint free rag If necessary refer to Identifying components in the engine compartment in this chapter for the location of the dipstick 6 Install the dipstick making sure it is fully seated in the filler tube 7 Remove the dipstick and inspect the fluid level The fluid should be in the designated area for normal operating temperature or ambient temperature Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is CD RAR COLD SEH SHOTS DONOT ADD Le above 10 C 50 F 4 Correct fluid level The transmission fluid should be checked at normal operating temperature 66 C 77 C 150 F 170 F on a level surface The normal operating temperature can be reached after approximately 3
16. passengers listen to another To activate from the rear seat controls press the A t control and plug a 3 5mm headphone into the headphone jack With the headphones ON the rear speakers will not operate In this mode the headphones are enabled The rear seat passengers have control over the desired volume levels Press the MODE control to toggle to the desired media source Use the SEEK VOLUME and MEM controls to make any desired adjustments Press the A i control again to engage the rear speakers and deactivate the Personal Audio Feature In this mode you can adjust the audio output to all system speakers front and rear together The rear seat passengers can not raise the volume of the system above the level on the front radio bezel Parental control Your Entertainment System allows you to have control over the rear seat controls The DVD system is automatically activated when the ignition is 50 Entertainment Systems ON This enables rear seat passengers to utilize the Rear Seat Controls RSC Once the headphone mode is activated the A symbol will appear in the radio display Press the memory preset controls 3 er and 5 simultaneously on the front ED ED ED ED L DED audio controls to disable the rear ji seat controls They will remain disabled until the front seat passengers enable them again by simultaneously pressing the 3 and 5 preset controls The settings of the front seat c
17. place for a long period of time wait until the cabin temperature of the vehicle is at normal temperature before operating the system Humidity and moisture condensation Moisture in the air will condense in the DVD player under extremely humid conditions or when moving from a cold place to a warm one If moisture condensation occurs do not insert a CD or DVD into the player If one is already in the player remove it Turn the DVD player ON to dry the moisture before inserting a DVD This could take an hour or more Cleaning the liquid crystal display LCD flip down screen Clean the display screen by applying a small amount of water or any ammonia based household glass cleaner directly to a soft cloth Rub the screen gently until the dust dirt or fingerprints are removed Do not spray the screen directly with water or glass cleaning solvents Overspray from these fluids could drip down into the internal electronics of the screen and cause damage Do not apply excessive pressure while cleaning the screen Foreign substances Exercise care to prevent dirt and foreign objects from entering the DVD player compartment Be especially careful not to spill liquids of any kind onto the media controls or into the videocassette player If liquid is accidentally spilled onto the system immediately turn the system OFF and consult a qualified service technician Cleaning compact discs Inspect all discs for contamination before playing If necessary cle
18. taken to another dealer If a particular dealership can not assist you then contact the Customer Relationship Center If you have questions or concerns or are unsatisfied with the service you are receiving follow these steps 1 Contact your Sales Representative or Service Advisor at your selling servicing dealership 2 If your inquiry or concern remains unresolved contact the Sales Manager or Service Manager at the dealership 3 If the inquiry or concern cannot be resolved at the dealership level please contact the Ford Customer Relationship Center Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service or if you need more help than the dealership could provide after following the steps described above contact the Ford Customer Relationship Center to find an authorized dealership to help you In the United States Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 1 800 392 3673 FORD TDD for the hearing impaired 1 800 232 5952 www ford com 209 Customer Assistance In Canada Customer Relationship Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD www ford ca If you own a Lincoln vehicle and are away from home when your vehicle needs service or if you need more help than the dealership could provide after following the
19. turned to the ON position RANGE Illuminates when 4L 4x4 Low is engaged Using the electronic shift 4WD system if equipped Positions of the electronic shift system To prevent damage the electronic shift 4WD system is designed to allow up to 45 seconds before a shift command is performed In the event that conflicting shift commands are selected allow up to 45 seconds for the shift command to be performed prior to reporting any shift concerns to your dealer 2H 2WD High For general on road driving Sends power to the rear wheels only 4H 4WD High For winter and off road conditions Sends power to front and rear wheels 171 Driving 4L 4WD Low For low speed off road cond applications that require extra power such as steep grades deep sand or pulling a boat out of the water Sends power to front and rear wheels Note Some noise may be heard as the 4WD system shifts or engages This is normal Shifting from 2WD 2WD High to 4x4 HIGH 4WD High Rotate the 4WD control to the 4x4 HIGH position at speeds up to 88 km h 55 mph e To prevent damage the electronic shift 4WD system is designed to engage 4x4 HIGH 4WD High when the vehicle is moving If shifted to 4x4 HIGH 4WD HIGH while at complete stop 4x4 may not engage and the 4x4 indicator may not illuminate until the vehicle is driven above 8 km h 5 mph Do not shift into 4x4 HIGH with the rear wheels slipping Shifting from 4x4 HIGH 4W
20. warning and indicator 10 ait DAS masr eena eE 12 anti lock brakes ABS 12 161 anti theft 0 0 ecceseeeesseeeeees 14 PrAKE ee ee 12 charging system n 13 Check COON ciccciccccssecsscsncesesss 11 cruise indicator sseriiiinssris 13 door AJAY sesciscencinevvieisevaseraemeiades 14 fuel cap light 0 eee 11 high Dedi snnennanirereroniss 13 HOW TUE E AE A 13 Safety belt srci ipce 12 service engine SOON n s 10 Index speed Control ccccceeeeees 94 turn signal indicator 13 Limited slip axle see Traction LOC ceee 163 Load limits 0 eceeeeeeeeeeees 181 GAWR waccdscscscsecssesossicsesesacdontens 181 GV WAR e E E 181 trailer towing secsesserosinieis 181 Loading instructions 183 Locks Atolo K seciaceabs esapctudacesasceccectd 115 Child PrOOL sseccssisAscisesee haere 109 GOOTS earnings enana 108 Lubricant specifications 263 265 Lumbar support seats 122 M Manual transmission fluid capacities 0 260 lubricant specifications 265 Message Center cceeeeeeeeeeees 95 english metric button 96 MENU DUTTON sssri 96 MITOS avner 83 automatic dimming rearview IAT OT oree a E A 88 fold AWAY ccececcececeesseceeeeneeees 90 heated c cceccsccsessscecsesseeeseteeees 89 side view mirrors power 89 Motorcraft parts 0 0 0 0 243 260 0 Octane rating 0 eee 242 Odometer derenin 18 Oil see Engine oil 0
21. 147 Seating and Safety Restraints Disposal of air bags and air bag equipped vehicles including pretensioners For disposal of air bags or air bag equipped vehicles see your local dealership or qualified technician Air bags MUST BE disposed of by qualified personnel SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children Also see Air bag supplemental restraint system SRS in this chapter for special instructions about using air bags Important child restraint precautions You are required by law to use safety restraints for children in the U S and Canada If small children ride in your vehicle generally children who are four years old or younger and who weigh 18 kg 40 lbs or less you must put them in safety seats made especially for children Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use When possible always place children under age 12 in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions Children and sa
22. ABOVE VIN XXXXXXXXXXXXXXXXX_ TYPE XXXXXXXXXXXXXXX MAXIMUM LOAD OCCUPANTS LUGGAGE XXXKG XXXXLB OCCUPANTS X TOTAL X FR X 2ND X RR OCCUPANTS LUGGAGE XX XXXKG XXXXLB TIRE XXXX XXXXX XXX X XXXKG XXXXLB PRESSURE FR XXX kPa XX PSI COLI SURE RR XXX kPa XX PSI COLD OWNER GUIDE DSO XXXX PRES TRAILER TOWING SEI EXT PNT XXXXXX XXXXXX_ RC XX BARTINTTR ITP PS TR TAXLE TTR SPR F0000 70000 X XX XXX X X XXXX UTC VFOHT 15294A10 GA 267 Vehicle identification number Maintenance and Specifications The vehicle identification number is attached to a metal tag and is located on the driver side COCE instrument panel Please note that in the graphic XXXX is representative of your vehicle x identification number 1 World manufacturer identifier XXX X XXXX X X X XXXXX 2 Brake type and gross vehicle weight rating GVWR d 3 Vehicle line series body type 5 S b b 4 Engine type 5 Check digit 6 Model year 7 Assembly plant 8 Production sequence number Engine number The engine number the last eight numbers of the vehicle identification number is stamped on the engine block transmission frame and transfer case if equipped 268 Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford Lincoln Mercury or Ford of Canada dealer These quality accessories have
23. Auto headlamp system with DRL Daytime Running Lights Battery Warmer Box Aluminum Rack cargo storage systems Daytime running lights Factory luggage rack adaptors Fog lights Framed luggage covers Hard and soft sided roof box Highway safety and first aid kit Multi sport track rider cross bars Multi sport track rider adaptors Spare tire soft storage cover Seat back pack storage Soft luggage cover Trailgate tables Towing mirrors Trailer hitch mounted bike carrier Trailer hitch bars and balls Trailer hitch swivel Tubular running bars TV video system Protection and appearance equipment Air bag anti theft locks Carpeted cargo mat Door edge guards Truck covers Cargo liners interior Carpet floor mats Cleaners waxes and polishes Flat splash guards Front end covers full Grill guards brush guards Hood deflectors 270 Accessories Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rear air deflectors Side window air deflectors Stainless grill insert Step bumpers Sun roof deflector Touch up paint Universal floor mats carpeted For maximum vehicle performance keep the following information in mind when adding accessories or equipment to your vehicle e When adding accessories equipment passengers and luggage to your vehicle do not exceed the total weight capacity of the vehicle or of the front or rear axle GVWR or GAWR as indicated on the Safety compliance certific
24. Cleaner Motorcraft Premium Car Wash Concentrate Motorcraft Carlite Glass Cleaner Canada only Ford Spot and Stain Remover Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra Clear Spray Glass Cleaner not available in Canada Ford Engine Shampoo and Degreaser May be sold with the Motorcraft name 224 Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location e We provide a scheduled maintenance guide which makes tracking routine service easy If your vehicle requires professional service your dealership can provide the necessary parts and service Check your Warranty Guide to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle e Do not work on a hot engine e When the engine is running keep loose clothing jewelry or long hair away from moving parts e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation e Keep all lit cigarettes open flames and other lit material away from the battery and all fuel related parts If you disconnect the
25. Cleaner Canada only Ford Extra Strength Tar and Road Oil Remover not available in Canada Ford Extra Strength Upholstery Cleaner not available in Canada Ford Custom Bright Metal Cleaner Motorcraft Premium Car Wash Concentrate Motorcraft Carlite Glass Cleaner Canada only Ford Spot and Stain Remover Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra Clear Spray Glass Cleaner not available in Canada Ford Engine Shampoo and Degreaser May be sold with the Motorcraft name 223 Cleaning FORD LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes These quality products have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and appearance of your vehicle Each product is made from high quality materials that meet or exceed rigid specifications For best results use the following or products of equivalent quality Ford Custom Clearcoat Polish Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant not available in Canada Motorcraft Vinyl Conditioner Canada only Ford Deluxe Leather and Vinyl Cleaner not available in Canada Motorcraft Vinyl Cleaner Canada only Ford Extra Strength Tar and Road Oil Remover not available in Canada Ford Extra Strength Upholstery Cleaner not available in Canada Ford Custom Bright Metal
26. Climate Controls Under normal weather conditions your vehicle s climate control system should be left in any position other than the MAX A C or OFF when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct Under snowy or dirty weather conditions your vehicle s climate control system should be left in the OFF position when the vehicle is parked This allows the climate control system to be free from contamination of outside pollutants If your vehicle has been parked with the windows closed during warm weather conditions the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Once the vehicle has been aired out operate the climate control system as desired Do not put objects under the front seat which may interfere with the airflow to the rear seats if equipped Remove any snow ice or leaves from the air intake area at the bottom of the windshield and underneath the hood Do not place objects over the defroster outlets These objects can block airflow and reduce visibility through your windshield Avoid placing small objects on top of the instrument panel These objects may fall down into the defroster outlets and block airflow in addition to damaging the climate control system To aid in side window defogging demisting in cold weather
27. Located in the left side storage compartment in the third row seating position Located on the right trim panel in the rear cargo area Driver Controls POWER WINDOWS Press and hold the rocker switches to open and close windows e Press the top portion of the l l rocker switch to close e Press the bottom portion of the rocker switch to open Express down e Press AUTO completely down and release quickly The driver s window will open fully Depress A again to stop window operation One touch down can be deactivated during operation by pushing down on the top part of the driver power window control 87 Driver Controls Window lock The window lock feature allows only the driver to operate the power windows To lock out all the window controls except for the driver s press the left side of the control Press the right side to restore the window controls Accessory delay if equipped With accessory delay the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened MIRRORS Automatic dimming inside rear view mirror if equipped Your vehicle is equipped with inside rear view mirror with an auto dimming function The electronic day night mirror will change from the normal state to the non glare state when bright lights glare reach the mirror When the mirror detects bright ligh
28. Open the hood 3 Remove the two screws and carefully disengage parking lamp turn signal assembly from the vehicle 4 Rotate bulb socket counterclockwise about 1 4 turn and remove from lamp assembly 5 Carefully pull bulb straight out of the socket and push in the new bulb 6 Install the bulb socket in lamp assembly by turning clockwise 7 Align the lamp assembly on the vehicle 8 Install two screws on parking lamp turn signal assembly 78 La Lights Replacing foglamp bulbs The halogen bulb contains gas under pressure The bulb may shatter if the glass envelope is scratched or if the bulb is dropped Handle the bulb carefully Grasp the bulb only by its base Avoid touching the glass envelope 1 Rotate the foglamp bulb counterclockwise and remove from foglamp the rear side of the foglamp is shown 2 Disconnect the electrical connector from the foglamp bulb 3 Connect the electrical connector to the new foglamp bulb 4 Install the foglamp bulb in foglamp by rotating clockwise Replacing tail lamp turn backup lamp bulbs The tail lamp turn backup lamp bulbs are located in the same portion of the tail lamp assembly one just below the other Follow the same steps to replace either bulb 1 Remove the four screws and the lamp assembly from vehicle 79 Lights 2 Rotate bulb socket counterclockwise about 1 4 turn and remove from lamp assembly 3 Carefully pull
29. P Park to another position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone 165 Driving P Park Always come to a complete stop before shifting into P Park Make P RN D 21 sure the gearshift lever is securely Sa es latched in P Park This position locks the transmission and prevents the rear wheels from turning Always set the parking brake fully and make sure the gearshift lever is latched in P Park Turn off the ignition whenever you leave your vehicle R Reverse With the gearshift lever in R Reverse the vehicle will move P RN D 21 a cir beaut ed fe complete stop before shifting into and out of R Reverse N Neutral With the gearshift lever in N Neutral the vehicle can be started P RN D 21 PAS Se ga and is free to roll Hold the brake pedal down while in this gear Overdrive The normal driving position for the best fuel economy Transmission operates in gears one through four Overdrive can be deactivated by pressing the transmission control switch TCS on the end of the gearshift lever The transmission control indicator light TCIL the word OFF on the end of the gearshift lever will illuminate 166 Driving Drive Not shown on the display Activate by pressing the transmission control switch TCS on the end of the gearshift lever with the gearshift in the position The TC
30. The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again AM FM select The AM FM select control works in radio tape and CD modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play AM FM select in CD mode Press this control to stop CD play and begin radio play Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 22 Entertainment Systems Setting memory preset stations 1 Select the frequency band with Va the AM FM select control oe PA 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations This feature is helpful on trips when you travel between cities with different radio stations Starting autoset memory preset 1 Select a frequency using the AM FM
31. Within 20 seconds program a remote transmitter by pressing any button on a transmitter The doors will lock unlock to confirm that the remote transmitter has been programmed If more than 20 seconds pass before pressing a remote transmitter button the programming mode will exit and the procedure will have to be repeated Repeat the previous step to program additional remote transmitters The doors will lock unlock to confirm that each remote transmitter has been programmed e When you have completed programming the remote transmitters turn the ignition to 3 OFF or wait 20 seconds Again the doors will lock unlock to confirm programming has been completed 113 Locks and Security Illuminated entry The illuminated entry system will turn on the interior lights when the remote transmitter unlock control is pressed The illuminated entry system will turn off the interior lights if the ignition switch is turned to the ON position or if the remote transmitter lock control is pressed or after 25 seconds of illumination The inside lights will not turn off if e they have been turned on with the dimmer control or e any door or liftgate is open The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the OFF position 10 minutes after if the dome lamp is off and 30 minutes after if the dome lamp switch is left on KEYLESS ENTRY SYSTEM With the keyless entry keypad you can e lock
32. an air bag SRS is provided It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly In a rollover crash an unbelted person is significantly more likely to die than a person wearing a safety belt Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the outside shoulder only Never wear the shoulder belt under the arm 2 Never swing the safety belt around your neck over the inside shoulder 3 Never use a single belt for more than one person Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints 131 Seating and Safety Restraints Combination lap and shoulder belts 1 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming a from until you hear a snap and feel a it latch Make sure the tongue is a securely fastened in the buckle 2 To unfasten push the release button and remove the tongue from the buckle a x N The front and rear outboard safety restraints in th
33. at any time beginning with step 2 in the Programming section Reprogramming a single HomeLink button To program a device to HomeLink using a HomeLink button previously trained follow these steps 1 Press and hold the desired HomeLink button Do NOT release the button 2 The red indicator light will begin to flash after 20 seconds Without releasing the HomeLink button follow step 2 in the Programming section For questions or comments contact HomeLink at www homelink com or 1 800 355 3515 102 Driver Controls OVERDRIVE CONTROL Activating overdrive Overdrive is the normal drive position for the best fuel economy The overdrive function allows automatic upshifts and downshifts through all available gears Deactivating overdrive Press the Transmission Control Switch TCS located on the end of the gearshift lever The Transmission Control Indicator Light TCIL the word OFF will illuminate on the end of the gearshift lever The transmission will operate in all gears except overdrive To return to normal overdrive mode press the Transmission Control overon Switch again The TCIL the word OFF will no longer be illuminated OVERORVE ag When you shut off and re start your vehicle the transmission will automatically return to normal Overdrive mode For additional information about the gearshift lever and the transmission control switch operatio
34. battery the engine must relearn its idle conditions before your vehicle will drive properly as explained in the Battery section in this chapter Working with the engine off 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Turn off the engine and remove the key 3 Block the wheels to prevent the vehicle from moving unexpectedly Working with the engine on 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Block the wheels to prevent the vehicle from moving unexpectedly Note Do not start your engine with the air cleaner removed and do not remove it while the engine is running 225 Maintenance and Specifications OPENING THE HOOD qm 1 Inside the vehicle pull the hood release handle located under the bottom left corner of the instrument panel 2 Go to the front of the vehicle and release the auxiliary latch located under the right center of the hood Slide the handle to release the auxiliary latch 3 Lift the hood until the lift cylinders hold it open IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5 4L V8 6 8L V10 gasoline engines Refer to the 7 3 Liter Power Stroke Direct Injection Turbo Diesel Owner s Guide Supplement for diesel engine component locations 226 Maintenance and Specifications 1 Battery 6 Power steering fluid reser
35. bumper of the vehicle is higher than it was unloaded will defeat the function of the load equalizing hitch and may cause unpredictable handling 185 Driving Safety chains Always connect the trailer s safety chains to the frame or hook retainers of the vehicle hitch To connect the trailer s safety chains cross the chains under the trailer tongue and allow slack for turning corners If you use a rental trailer follow the instructions that the rental agency gives to you Do not attach safety chains to the bumper Trailer brakes Electric brakes and manual automatic or surge type trailer brakes are safe if installed properly and adjusted to the manufacturer s specifications The trailer brakes must meet local and Federal regulations Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase The braking system of the tow vehicle is rated for operation at the GVWR not GCWR Trailer lamps Trailer lamps are required on most towed vehicles Make sure your trailer lamps conform to local and Federal regulations See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps Using a step bumper if equipped The rear bumper is equipped with an integral hitch and only requires a ball with a 25 4 mm one inch shank diameter The bumper has a
36. conditions 1 Select the position that distributes air through the Panel and Floor 2 Set the temperature control to full heat 3 Set the fan speed to full fan 4 Direct the outer panel vents towards the side windows 5 To increase airflow to the outer panel vents close the central panel vents Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop 61 Climate Controls ELECTRONIC AUTOMATIC TEMPERATURE CONTROL EATC SYSTEM IF EQUIPPED EXT TEMP G0 e J OFF 0 C a GU ys D E i amp o A C control Windshield defrost control Recirculated air control Fan speed control Windshield and floor control Floor control Panel and floor control Panel control OFF control 10 AUTO control 11 External temperature control oO 0O N oA WOW HY 12 Temperature control The EATC system will maintain a selected temperature and automatically control airflow You can override automatic operation with any of the override controls the fan speed control or the steering wheel controls if equipped 62 Climate Controls Turning the EATC on om 7 auto EXT TEMP Yes calealecales Press AUTO any of the override controls or the fan speed control The EATC will only operate when the vehicle is running Turning the EATC system o
37. designed to inflate in rear and side crashes or rollovers Td rather be Not a good idea People who are ejected are 40 thrown clear times more likely to DIE Safety belts help prevent ejection WE CAN T PICK OUR CRASH 140 Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime Sitting on the safety belt will increase the risk of injury in an accident To disable one time or deactivate the Belt Minder feature please follow the directions stated below One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle BeltMinder will be disabled for that ignition cycle only Deactivating activating the BeltMinder feature Read steps 1 9 thoroughly before proceeding with the deactivation activation programming procedure The BeltMinder feature can be deactivated activated by performing the following procedure Before following the procedure make sure that e the parking brake is set e the gearshift is in P Park automatic transmission e the ignition switch is in the OFF position e all vehicle doors are closed the driver s safety belt is unbuckled the parklamps headlamps are in OFF position If vehicle is equipped with Autolamps this will not affect the procedure To reduce the risk of injury do not deactivate activate the Belt Minder feature while driving the vehicle 1 Turn the ignition switch to the RUN
38. extracted e Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode 133 Seating and Safety Restraints How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Disconnect the combination lap shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive emergency locking mode After any vehicle collision the seat belt system at all outboard seating positions except driver which has no automatic locking retractor feature must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly In addition all seat belts should be checked for proper function BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly automatic locking retractor feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions Energy Management Feature e This vehic
39. for the following reasons e your vehicle was not perfectly level during fill up e differences in the automatic shut off points on the fuel pumps at service stations e variations in top off procedure from one fill up to another e rounding of the displayed values to the nearest liter gallon To reset the average fuel economy 1 Press the MODE control repeatedly until average fuel economy is displayed this is the only resettable display 96 Driver Controls 2 Press the E M and MODE controls simultaneously The display 4 4 will illuminate the AVG indicator While the indicator is lit release both controls to reset the average fuel economy Fuel range This displays the approximate number of kilometers miles left to drive before the fuel tank is empty The indicated distance to empty may be inaccurate e with sustained drastic changes in fuel economy such as trailer towing but will eventually recover e if the vehicle is started while parked on an incline e if less than 30 liters 8 gallons of fuel is added to the fuel tank The fuel range function will flash for five seconds at the following distances based on fuel remaining and fuel economy calculations e 80 km 50 miles e 40 km 25 miles e 16 km 10 miles Outside air temperature if equipped The temperature can be displayed in Centigrade or Fahrenheit by pressing the E M control If the outside tem
40. highway driving because they are more likely to blow out or fail You should carefully observe the recommended tire inflation pressure found on the safety compliance certification label attached to the left front door lock facing or door latch post pillar Failure to follow tire pressure recommendations can adversely affect the way your vehicle handles Do not exceed the Ford recommended pressure even if it is less than the maximum pressure allowed for the tire Each day before you drive check your tires If one looks lower than the others use a tire gauge to check pressure of all tires and adjust if required Check tire pressure with a tire gauge every few weeks including spare Safe operation requires tires that are neither underinflated nor overloaded Periodically inspect the tire treads and remove stones nails glass or other objects that may be wedged in the tread grooves Check for holes or cuts that may permit air leakage from the tire and make necessary repairs Inspect the tire side walls for cuts bruises and other damage If internal damage to the tire is suspected have the tire demounted and inspected in case it needs to be repaired or replaced Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide both reasonably safe predictable performance whether loaded or empty and durable load carrying capability For this reason Ford strongly recommends
41. is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 Setting memory preset stations 1 Select the frequency band with the AM FM select control Press the AM FM control to toggle between AM FM1 or FM2 2 Press the SEEK control to access the next listenable station up or down the frequency band Press the TUNE control to go up or down the listening band in individual increments 3 Select a station Refer to Seek function for more information on selecting a station 31 Entertainment Systems 4 Press and hold a memory preset control The playing media will mute momentarily When the sound returns the station is held in memory on the control you selected The display will read SAVED SOMO Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations This feature is helpful on trips when you travel between cities with different radio stations Starting autostore 1 Press and momentarily hold the AM FM control 2 AUTOSET will flash in the display as the frequency band is scrolled through 3 When the six strongest stations are filled the station stored in memory preset control 1 will start playing If there are fewer than six strong stations available on the frequency band the remaining memory preset controls will all sto
42. is too short when fully extended there is a 20 cm 8 inch safety belt extension assembly that can be added part number 611022 This assembly can be obtained from your dealer at no cost Use only extensions manufactured by the same supplier as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for you when fully extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged Inspect the safety belts to make sure there are no nicks tears or cuts Replace if necessary All safety belt assemblies including retractors buckles front seat belt buckle assemblies buckle support assemblies slide bar if equipped shoulder belt height adjusters Gf equipped shoulder belt guide on seatback Cif equipped child safety seat tether bracket assemblies if equipped LATCH child seat tether anchors and lower anchors if equipped and attaching hardware should be inspected after a collision Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced However if the collision was minor 142 Seating and Safety Restraints and a qualified technician finds that the belts do not show damage and continue to operate properly they do n
43. least eight hours without starting the engine Then start the engine and complete the above driving cycle The engine must warm up to its normal operating temperature Once started do not turn off the engine until the above driving cycle is complete 248 Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid Refer to the scheduled maintenance guide for the service interval schedules If adding fluid is necessary use only MERCON ATF Check the fluid level when it is at ambient temperature 20 80 F 7 25 C 1 Check the fluid level on the dipstick It should be between the arrows in the FULL COLD range Do not add fluid if the level is within this range 2 If the fluid level is low start the engine 3 While the engine idles turn the steering wheel left and right several times 4 Turn the engine off 5 Recheck the fluid level on the dipstick Do not add fluid if the level is between the arrows in the FULL COLD range 6 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the FULL COLD range Be sure to put the dipstick back in the reservoir 249 Maintenance and Specifications BRAKE FLUID C Checking and adding brake fluid Brake fluid should be checked and refilled as needed Refer to the scheduled maintenance guide for the service interval schedules 1 Clean the reservoir cap before r
44. not have been properly installed and securely tightened These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and or properly installing and securely tightening the fuel cap After three driving cycles without these or any other temporary malfunctions present the light should turn off A driving cycle consists of a cold engine startup followed by mixed city highway driving No additional vehicle service is required 10 Instrument Cluster If the light remains on have your vehicle serviced at the first available opportunity Light is blinking Engine misfire is occurring which could damage your catalytic converter You should drive in a moderate fashion avoid heavy acceleration and deceleration and have your vehicle serviced at the first available opportunity Under engine misfire conditions excessive exhaust temperatures could damage the catalytic converter the fuel system interior floor coverings or other vehicle components possibly causing a fire Check fuel cap if equipped Illuminates when the fuel cap is not installed correctly Check the fuel RY cap for proper installation When AS the fuel filler cap is properly re installed the light s will turn off after a period of normal driving Continuing to operate the vehicle with the check fuel cap light on mis installed can activate the Service Engine Soon Check Engine warning light It may t
45. on and off 0 72 warning CHIME csscssecscesseencessteecs 14 Heating heating and air conditioning SVSUCIUL oea 59 62 HomeLink universal transceiver see Garage door opener e 99 100 102 HOO sepana aces 226 I Ignition sissies remas 156 265 266 Infant seats see Safety seats oo eee 149 Inspection maintenance I M COSTING scoicccssnsciseslsancssicsaeesnanceearve 248 Instrument panel CLEANING sii cesscediagcesiucd exatiasiadess 221 CISTET hirere an 10 lighting up panel and MILCMIOL E E E 74 J ACK reeset R R 196 POSIOMING sassncs cavateervankruavanerie 196 SUOVOSC Sie EE 196 Jump starting your vehicle 201 Index K Keyless entry system aAUtolOCk sinensis 115 locking and unlocking doors 115 programming entry code 114 KEYS ase2eecoceestastiedeaasenkidess 117 118 key in ignition chime 15 positions of the ignition 156 L Lamps autolamp system n s 72 76 bulb replacement specifications chart 0 76 cargo lamps aveuisicceesecessisecseeiaees 74 daytime running light 73 fog lamps ssaccvseacevivsieiechesnceraesasenr 73 headlamps cccscccseesseceseeseeees 2 headlamps flash to pass 73 instrument panel dimming 74 interior lamps 74 75 77 replacing bulbs 1 0 76 80 Lane change indicator see Turn signal ccceeee 74 Liftgate asevsssssvesvtbicscvssarsencedicctsceys 105 Lights
46. power distribution box The fuse panel is located below and to the left of the steering wheel by the brake pedal Remove the panel cover to access the fuses 192 Roadside Emergencies To remove the fuse panel cover turn the panel fasteners counterclockwise To remove a fuse use the fuse puller tool provided on the fuse panel L cover 2 o S B x amp S amp S 8 102 108 Relay 301 Relay 304 Relay 307 Relay 210 Relay 302 Relay 305 Relay 303 Relay 306 Ea N Breaker 601 ed N N l 2 Fey N 115 116 xo Gd A el a Ls ca T 9 E The fuses are coded as follows 193 Roadside Emergencies Fuse Relay Fuse Amp Passenger Compartment Fuse Panel 1 2 20A Power point floor console T P CC Noted S O 14 15A Turn lamps Brake on off switch high Body security module 4x4 module P20 CO Noted Cd 4 Wheel Anti Lock Brake System 4WABS Ignition switch Run feed EATC module module Front blower relay coil Customer access 194 Roadside Emergencies Fuse Relay Fuse Amp Passenger Compartment Fuse Panel Location 30 15A 31 15A P89 CC Noted o O Door locks Body security module 110 Ignition switch no 195 Roadside Emergencies Fuse Relay Fuse Amp Passenger Compartment Fuse Panel 602 60A 4 Wheel Anti Lock Brake System 4WABS module 210 COC Notused CCCs pt
47. quality Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components If you have run out of fuel e You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine e Your Service Engine Soon indicator may come on For more information on the Service Engine Soon indicator refer to the Instrument cluster chapter Fuel Filter For fuel filter replacement see your dealer or a qualified service technician Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter Replace the fuel filter with an authorized Motorcraft part The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you the driver You must gather information as accurately and consistently as 243 Maintenance and Specifications possible Fuel expense frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy We do not recommend taking fuel economy measurements during the first 1 600 km 1 000 miles of driving engine break in period You will get a more accurate measurement after 3 000 km 5 000 km 2 000 miles 3 000 miles Filling the tank The a
48. rearward For assistance refer to the label located on the seat side shield 124 Seating and Safety Restraints 1 Lift strap to release seat cushion 2 Lift seat cushion up and rotate forward 3 The headrest must be removed in order to fold the seatback down Remove 2nd row seat headrest by pushing in both tabs while pulling up on headrest simultaneously 125 Seating and Safety Restraints 4 Stow headrest into the green caps found on the top of the seat cushion 5 Lift the lower seat control and flip the seatback down 126 Seating and Safety Restraints 6 For bench seats only lift up flap on seatback to release closeout panel 7 For bench seats only rotate panel to closeout the space between the seatback and the floor Returning the seat to upright Insure the seat is pulled back to the locked position whether the seat is occupied or empty If not latched the seat may cause injury during a sudden stop 1 For bench seats rotate the closeout panel onto the seatback and secure with the retaining flap 2 Lift the lower seat control 3 Pull up on the seatback while lifting the handle to lift the seatback into the upright position 127 Seating and Safety Restraints 4 Remove headrest from storage position and return to 2nd row seatback Push down headrest completely to secure Reclining the s
49. s engine is electronically controlled by a computer some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle and fuel trim strategy for optimum driveability and performance To begin this process 1 With the vehicle at a complete stop set the parking brake 2 Put the gearshift in P Park turn off all accessories and start the engine 3 Run the engine until it reaches normal operating temperature 4 Allow the engine to idle for at least one minute 5 Turn the A C on and allow the engine to idle for at least one minute 6 Release the parking brake With your foot on the brake pedal and with the A C on put the vehicle in D Drive and allow the engine to idle for at least one minute 7 Drive the vehicle to complete the relearning process e The vehicle may need to be driven 16 km 10 miles or more to relearn the idle and fuel trim strategy e If you do not allow the engine to relearn its idle trim the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned 232 Maintenance and Specifications If the battery has been disconnected or a new battery has been installed the clock must be reset once the battery is reconnected e Always dispose of automotive i P batteries in a responsible manner s S Follow your local authorized LY G standards for disposal Call your t
50. select controls 2 Press the control 3 When the first six strong stations are filled the station stored in memory preset control 1 will start playing If there are less than six strong stations available on the frequency band the remaining memory preset controls will all store the last strong station available These stations are temporarily stored in the memory preset controls until deactivated and are accessed in the same manner as your original presets To deactivate autoset and return to your audio system s manually set memory stations press the AUTO control again 23 Entertainment Systems Setting the clock To set the hour press and hold the CLK control and press SEEK e lt q to decrease hours and p gt to increase hours To set the minute press and hold the CLK control and press TUNE e A to decrease minutes and e P to increase minutes If your vehicle has a separate clock 4 amp other than the digital radio display the CLK control will not function in the above manner The CLK control will allow you to switch between media display mode radio station stereo information etc and clock display mode time When in clock mode the media information will display for 10 seconds when the radio is turned on and then revert to clock information Any time that the media is changed new radio station etc the media information will again display for 10 seconds before reverti
51. used as chains may chip aluminum wheels Follow these guidelines when using snow tires and chains e Use only SAE Class S chains e Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines e Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work remove the chains to prevent damage to your vehicle e If possible avoid fully loading your vehicle e Remove the tire chains when they are no longer needed Do not use tire chains on dry roads e The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains 259 Maintenance and Specifications MOTORCRAFT PART NUMBERS Component PCV valve EV 233 EV 233 BXT 65 750 BXT 65 750 Spark plugs platinum AGSF 22W AGSF 22W Refer to the 7 3 Liter Power Stroke Direct Injection Turbo Diesel Owner s Guide Supplement for Motorcraft diesel engine service part numbers Refer to Vehicle Emissions Control Information VECI decal for spark plug gap information REFILL CAPACITIES Ford Part NUR Ge A Front axle Motorcraft SAE 4X4 vehicles 1 8L 8 8 pints 75W 90 Premium 4x4 Front Axle Lubricant Rear axle Motorcraft SAE All 3 3L 6 9 pints 75W 140 A Synthetic Rear Axle Lubricant Brake fluid High All Fill to line on Performance reservoir DOT 3 Motor Vehicle Bra
52. wearers to wear safety belts all of the time 139 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts All statistics based on U S data Reasons given Consider Crashes are rare 36 700 crashes occur every day The more we events drive the more we are exposed to rare events even for good drivers 1 in 4 of us will be seriously injured in a crash during our lifetime Belts are We design our safety belts to enhance comfort If uncomfortable you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible this can improve comfort I was in a hurry Prime time for an accident BeltMinder reminds us to take a few seconds to buckle up Seat belts don t Safety belts when used properly reduce risk of work death to front seat occupants by 45 in cars and by 60 in light trucks crashes many when no other vehicles are around Belts wrinkle my _ Possibly but a serious crash can do much more than wrinkle your clothes particularly if you are unbelted The people I m Set the example teen deaths occur 4 times more with don t wear often in vehicles with TWO or MORE people belts Children and younger brothers sisters imitate behavior they see T have an air bag Air bags offer greater protection when used with safety belts Frontal airbags are not
53. 0 228 OVETAT VE ici isieescsksisdanceiedmcsaders 103 276 P Panic alarm feature remote entry SYSUGIY 5 cccccseetesssssvencdenescs 112 Parking brake isisisi 162 Parts see Motorcraft parts 260 Pedals see Power adjustable foot pedals wo ceceeeceeesseeeeee 90 Power adjustable foot pedals 121 Power distribution box see FUSES eecccesessceeeeseeees 192 Power door locks 108 115 Power MULTOTS ccecceseeeeseeeeees 89 Power DOU sesceissdeerresiziiseeesis os 85 Power steering o 163 fluid checking and adding 249 fluid refill capacity 260 fluid specifications 263 265 Power Windows cccccseeeees 87 Preparing to drive your Vehicle ccccccceeeeseeees 164 R Radio saae vinsceva te feakteecats 19 28 Radio reception ccceeeeeeees 58 Rear window defroster qI Roays aranan ts 191 Remote entry system 109 112 illuminated entry ccceee 114 locking unlocking COOLS sirrinin 108 110 111 PANIC BALM eee eeeeeeeeeees 112 replacement additional TVANSMIUCCETS essiens 113 replacing the batteries 112 Reverse sensing system 168 Roadside assistance 1 0 0 189 Roof rack woe eeeeeeeeeeeeeeeeseeeeeees 106 S Safety belts see Safety restraints 14 130 132 134 137 Safety defects reporting 217 Safety restraints 130 182 134 136 137 belt minder 139 clea
54. 0 km 20 miles of driving 251 Maintenance and Specifications You can check the fluid without driving if the ambient temperature is above 10 C 50 F However if fluid is added at this time an overfill condition could result when the vehicle reaches normal operating temperature The transmission fluid should be in _ this range if at normal operating temperature 66 C 77 C apo FREE COLD EE 150 F 170 F The transmission fluid should be in 4 this range if at ambient temperature 10 C 35 C 50 F 95 F q be High fluid level Fluid levels above the safe range may result in transmission failure An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage High fluid levels can be caused by an overheating condition Adjusting automatic transmission fluid levels Before adding any fluid make sure the correct type is used The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in this chapter Use of a non approved automatic transmission fluid may cause internal transmission component damage If necessary add fluid in 250 ml 1 2 pint increments through the filler tube until the level is correct 252 Maintenance and Specifications If an overfill occurs excess fluid should be removed by a qualified technician An overfill condition of tran
55. 2002 Excursion Table of Contents Introduction 4 Congratulations 4 Safety and environment protection 5 Symbol glossary 8 Instrument Cluster 10 Warning and control lights 10 Gauges 15 Entertainment Systems 19 AM FM stereo cassette with CD 19 AM FM stereo with CD 28 Rear seat entertainment system 43 Climate Controls 59 Manual heating and air conditioning 59 Electronic automatic temperature control 62 Lights 72 Headlamps 72 Turn signal control 74 Bulb replacement 76 Interior lamps TT Driver Controls 81 Windshield wiper washer control 81 Steering wheel adjustment 83 Power windows 87 Mirrors 89 Speed control 91 Message center 95 Table of Contents Locks and Security Keys Locks Anti theft system Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Transmission operation Vehicle loading Trailer towing Recreational towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut off switch Fuses and relays Changing tires Jump starting Wrecker towing Customer Assistance The dispute settlement board Utilizing the mediation arbitration Getting assistance outside the U S and Canada Ordering additional owner s literature Reporting safety defects U S only 108 108 108 109 120 120 130 143 148 156 156 160 164 181 184 188 189 189 190 190 191 196 201 207 209 211 21
56. 4 A or yellow colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS M97B51 A1 To determine your vehicle s coolant type color check your coolant reservoir Add Motorcraft Premium Engine Coolant green colored VC 4 A U S or CXC 10 Canada or Motorcraft Premium Gold Engine Coolant yellow colored VC 7 A VC 7 B in Oregon depending on the type of coolant originally equipped in your vehicle If you are unsure which type of coolant your vehicle requires check your coolant reservoir or contact your local dealer Note Use of Motorcraft Cooling System Stop Leak Pellets VC 6 darkens the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan Do not add mix an orange colored extended life coolant such as Motorcraft Speciality Orange Engine Coolant VC 2 US or CXC 209 Canada meeting Ford specification WSS M97B44 D with the factory filled coolant Mixing Motorcraft Speciality Orange Engine Coolant or any orange colored extended life product with your factory filled coolant can result in degraded corrosion protection A large amount of water without engine coolant may be added in case of emergency to reach a vehicle service location In this instance the cooling system must be drained and refilled with a 50 50 mixture of engine coolant and distilled water as soon as possible Water alone without engine coolant can cause engine damage from corrosion overheating or freezing Do no
57. 4 215 216 217 Table of Contents Cleaning 218 Cleaning your vehicle 218 Underbody preservation 222 Maintenance and Specifications 225 Hood 226 Engine compartment 226 Engine oil 228 Battery 231 Fuel information 239 Air filter s 254 Part numbers 260 Refill capacities 260 Lubricant specifications 263 Engine data 265 Vehicle dimensions 266 Accessories 269 Index 272 All rights reserved Reproduction by any means electronic or mechanical including photocopying recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company Ford may change the contents without notice and without incurring obligation Copyright 2001 Ford Motor Company Introduction The following warning may be required by California law CALIFORNIA Proposition 65 Warning WARNING Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm In addition certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm CONGRATULATIONS Congratulations on acquiring your new Ford Please take the time to get well acquainted with your vehicle by reading this handbook The more you know and understan
58. 4WD System and 4WD Low is selected while the vehicle is moving the 4WD system will not engage This is normal and should be no reason for concern Before 4WD Low can be engaged the vehicle must be brought to a complete stop the brake pedal depressed and the transmission placed in N Neutral The 4WD system e provides 4x4 High engagement and disengagement while the vehicle is moving is operated by a rotary control located on the instrument panel that allows you select 2WD 4x4 High or 4x4 Low operation e uses auto manual hub locks that can be engaged and disengaged automatically based on the 4x4 mode selected 170 Driving e auto manual hub locks can be manually overridden by rotating en a the hub lock control from AUTO _ _ a to LOCK if desired e automatic operation of the hub locks is recommended and will increase fuel economy e For proper operation make sure that the arrow and the indicator dot on the hub are aligned and that both hub locks are set the same both set to AUTO or both set to LOCK 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions If these lights illuminate when driving in 2WD contact your Ford dealer as soon as possible e 4x4 momentarily illuminates after the engine is started 4x4 Illuminates when 4H 4x4 High or 4L 4x4 Low is engaged e LOW RANGE momentarily LOW illuminates when the ignition is
59. 50 165 Torque specifications are for nut and bolt threads free of dirt and rust All 2 piece flat wheel nuts apply a light machine oil between the flat washer and the nut Use only Ford recommended replacement fasteners JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Batteries contain sulfuric acid which can burn skin eyes and clothing if contacted Do not attempt to push start your vehicle Automatic transmissions do not have push start capability also the catalytic converter may become damaged Preparing your vehicle When the battery is disconnected or a new battery is installed the transmission must relearn its shift strategy As a result the transmission may have firm and or soft shifts This operation is considered normal and 201 Roadside Emergencies will not affect function or durability of the transmission Over time the adaptive learning process will fully update transmission operation 1 Use only a 12 volt supply to start your vehicle 2 Do not disconnect the battery of the disabled vehicle as this could damage the vehicle s electrical system 3 Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts 4 Check al
60. COAST To set a speed e Press SET ACCEL For speed control to operate the speed control must be ON and the vehicle speed must be greater than 48 km h 80 mph 91 Driver Controls If you drive up or down a steep hill your vehicle speed may vary momentarily slower or faster than the set speed This is normal Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill If your vehicle speed is faster than the set speed while driving on a downhill you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed If your vehicle slows down more than 16 km h 10 mph below your set speed on an uphill your speed control will disengage This is normal Pressing RES will re engage it Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved To set a higher set speed e Press and hold SET ACCEL Release the control when the desired vehicle speed is reached or Press and release SET ACCEL to operate the Tap Up function Each press will increase the set speed by 1 6 km h 1 mph or Accelerate with your accelerator pedal When the desired vehicle speed is reached press and release SET ACCEL You can accelerate with the accelerator pedal at any time during speed control usage Releasing the accelerator pedal will return your vehicle to the previously programmed set speed 92 To set a lower set speed
61. D High to 2WD 2WD High Rotate the 4WD control to 2WD at any forward speed Disengagement of the transfer case and front hubs may be delayed due to torque bind which is caused by driving on dry hard surfaces or performing tight turns while using the 4WD system e You do not need to operate the vehicle in R Reverse to disengage your front hubs but it will eliminate any torque bind and allow the system to immediately disengage Shifting from 4x4 HIGH 4WD High to 4x4 LOW 4WD Low 1 Bring the vehicle to a complete stop 2 Depress the brake 172 Driving 3 Place the gearshift in N Neutral 4 Move the 4WD control to the 4x4 LOW position 5 Hold the shift conditions until the LOW RANGE indicator light illuminates 6 If the LOW RANGE indicator light does not illuminate within 15 seconds drive the vehicle above 8 km h 5 mph then repeat steps 1 through 5 before reporting any shift concerns to your dealer Shifting from 4x4 LOW 4WD Low to 4x4 HIGH 4WD High or 2WD 2WD High 1 Bring the vehicle to a complete stop 2 Depress the brake 3 Place the gearshift in N Neutral 4 Move the 4WD control to the 4x4 HIGH 4WD High or 2WD 2WD High position 5 Hold the shift conditions until the LOW RANGE indicator light shuts off 6 If the LOW RANGE indicator light does not shut off within 15 seconds drive the vehicle above 8 km h 5 mph then repeat steps 1 through 5 before re
62. ED P O Box 07150 Detroit Michigan 48207 Or call For a free publication catalog order toll free 1 800 782 4356 Monday Friday 8 00 a m 6 00 p m EST Items in this catalog may be purchased by credit card holders only Obtaining a French owner s guide French Owner s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada Limited Service Publications P O Box 1580 Station B Mississauga Ontario L4Y 4G3 IN CALIFORNIA U S ONLY California Civil Code Section 1793 2 d requires that if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle s applicable express warranty after a reasonable number of attempts the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer less a reasonable allowance for consumer use The consumer has the right to choose whether to receive a refund or replacement vehicle California Civil Code Section 1793 22 b presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if within the first 18 months of ownership of a new vehicle or the first 29 000 km 18 000 miles whichever occurs first 1 Two or more repair attempts are made on the same nonconformity likely to cause death or serious
63. Fa portion of the seat cushion 7 Press the control to move the seat forward backward up or down Manual seat memory feature The manual adjust seat and seatback may lose their memory positions and not latch in the desired place To reset the memory position move the seat to the most forward position then push the seatback rearward until the seatback locks This should ensure that the seatback is realigned to the desired rest position 123 Seating and Safety Restraints Heated seats if equipped To operate the heated seats e Push control to activate _ f WW e Push again to deactivate C w J gt The indicator light on the control will iluminate when activated REAR SEATS Head restraints Your vehicle s seats are equipped with head restraints which adjust up and down The purpose of these head restraints is to help limit head motion in the event of a rear collision To properly adjust your head restraints lift the head restraint so that it is located directly behind your head or as close to that position as possible Refer to the following to raise and lower the head restraints Push or pull the head restraint to ai the desired position y Rear folding seats if equipped Folding down rear seats into load floor Ensure that no objects such as books purses or briefcases are on the floor in front of the second row seats before folding them down and insure the seat is fully latched
64. IL the word OFF will illuminate on the gearshift lever Transmission operates in gears one through three Drive provides more engine braking than Overdrive and is useful when e driving with a heavy load e towing a trailer up or down steep hills e additional engine downhill braking is desired If towing a trailer refer to Driving while you tow in the Trailer towing section To return to Overdrive mode press the transmission control switch TCS The TCIL the word OFF will no longer be illuminated Each time the vehicle is started the transmission will automatically return to normal overdrive mode Every time the vehicle is shut off and restarted you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired 2 Second Use 2 Second to start up on slippery roads or to provide additional engine braking on downgrades 1 First Use 1 Low to provide maximum engine braking on steep downgrades Upshifts can be made by shifting to 2 Second or to ene PRNO2z oe Overdrive Selecting 1 Low at higher speeds causes the transmission to shift to a lower gear and will shift to 1 Low after vehicle decelerates to the proper speed Forced Downshifts To gain acceleration in Overdrive or Drive O D OFF when passing another vehicle push the accelerator to the floor The transmission will downshift to the appropriate gear third s
65. Start with the ignition in OFF and the autolamps selected 2 Deselect the autolamps 3 Put the ignition in RUN 4 Put the ignition in OFF 5 Select the autolamps Steps 2 through 5 must be performed within a 10 second period At this point the headlamps and parking lamps will turn on 6 Deselect the autolamps after the desired autolamp delay time maximum of 3 minutes At this point the headlamps and parking lamps will turn off 72 Lights Foglamp control if equipped 0 The headlamp control also operates the foglamps The foglamps can be turned on only when the headlamp control is in the gD and position and the high beams are not turned on Pull headlamp control towards you K to turn foglamps on The foglamp indicator light will illuminate if the ignition is in the RUN position Daytime running lamps DRL if equipped Turns the headlamps on with a reduced output To activate e the ignition must be in the ON position and e the headlamp control is in the OFF or Parking lamps position Always remember to turn on your headlamps at dusk or during inclement weather The Daytime Running Lamp DRL system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions Failure to activate your headlamps under these conditions may result in a collision High beams FD e Push forward past detent to activate e Pull toward you past detent to deactivate F
66. The first track of the disc will begin playing After that CD play will begin where it stopped last If an alternative CD is desired press the corresponding preset control 1 6 of a loaded CD or press the TUNE control to access the other loaded CDs NO CD will display if the CD control is activated when there is not a CD present in the audio system NO CD will illuminate in the display if the CD control and a present number that is currently empty are pressed The system will play the next available disc CD units are designed to play commercially pressed 12 cm 4 75 in audio compact discs only Due to technical incompatibility certain recordable and re recordable compact discs may not function correctly when used in Ford CD players Irregular shaped CDs CDs with a scratch protection film attached and CDs with homemade paper adhesive labels should not be inserted into the CD player The label may peel and cause the CD to become jammed It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels Ball point pens may damage CDs Please contact your dealer for further information Display description Six circles are always lit in the digital display These signify the six CD slots in the audio system When a disc is loaded into a particular slot 1 6 the number inside that specific circle lights If the circle is empty there is no CD in that particular slot 34 Enter
67. XT 2 QDX MERCON fluid and MERCON ATF transfer case fluid Gf equipped Automatic Motorcraft XT 2 QDX fie transmission MERCON ATF Windshield Ultra clear C9AZ 19550 AC a M17P5 A washer fluid Windshield Washer Concentrate 1 Add 236 ml 8 oz of Additive Friction Modifier C8AZ 19B546 A or equivalent meeting Ford specification EST M2C118 A for complete refill of Traction Lok axles Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water Ford specification 264 Maintenance and Specifications 2Ensure the correct automatic transmission fluid is used Transmission fluid requirements are indicated on the dipstick or on the dipstick handle Check the container to verify the fluid being added is of the correct type Refer to your scheduled maintenance guide to determine the correct service interval Some transmission fluids may be labeled as dual usage such as MERCON and MERCON V These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON type fluid However these dual usage fluids may be used in transmissions that require the MERCON V type fluid MERCON and MERCONE V type fluids are not interchangeable DO NOT mix MERCON and MERCONE V Use of a transmission fluid that indicates dual usage MERCON and MERCON V in an automatic transmission application requiring MERCON may cause transmis
68. a collision Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips not across the waist e lst row and 3rd row if equipped center seating positions The lap belt does not adjust automatically 137 Seating and Safety Restraints Insert the tongue into the correct buckle the buckle closest to the direction the tongue is coming from To lengthen the belt turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle To tighten the belt pull the loose end of the belt through the tongue until it fits snugly across the hips Shorten and fasten the belt when not in use e 2nd row center seating position if equipped The lap belt will adjust automatically To fasten grasp the tongue and with a continuous motion pull out enough webbing to buckle the tongue into the correct buckle If you did not pull out enough webbing to reach the buckle allow the tongue to retract fully before trying to pull it out again Safety belt warning light and indicator chime A The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts 138 Seating and Safety Restraints Conditions of operation The driver s safety belt is not buckled before the ignition switch is turned to the ON position The driver s safety belt is buckled while the indicator light is illum
69. afety and operating instructions before operating the system and retain for future reference Do not attempt to service repair or modify the Rear Seat Entertainment System RSES See your Ford or Lincoln Mercury dealer 54 Entertainment Systems Do not insert foreign objects into the DVD compartment The front glass on the liquid crystal display LCD flip down screen may break when hit with a hard surface If the glass breaks do not touch the liquid crystalline material In case of contact with skin wash immediately with soap and water Do not expose the liquid crystal display LCD flip down screen to direct sunlight or intensive ultraviolet rays for extensive periods of time Ultraviolet rays deteriorate the liquid crystal Be sure to review User Manuals for video games and video game equipment when used as auxiliary inputs for your Rear Seat Entertainment System RSES Do not operate video games or video equipment if the power cords and or cables are broken split or damaged Carefully place cords and or cables where they will not be stepped on or interfere with the operation of seats and or compartments Disconnect video games and video equipment power cords and or cables when not in use Avoid touching auxiliary input jacks with your fingers Do not blow on them or allow them to get wet or dirty Do not clean any part of the DVD layer with benzene paint thinner or any other solvent Federal Communication Commissio
70. ain reimbursement information call 1 800 665 2006 ROADSIDE COVERAGE BEYOND BASIC WARRANTY In the United States you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer Similarly in Canada for uninterrupted Roadside Assistance coverage you may purchase extended coverage prior to your Basic Warranty s Roadside Assistance expiring For more information and enrollment contact 1 877 294 2582 or visit our website at www ford ca HAZARD FLASHER A Use only in an emergency to warn traffic of vehicle breakdown approaching danger etc The hazard flashers can be operated when the ignition is off e The hazard lights control is located on top of the steering column Depress hazard lights control to activate all hazard flashers simultaneously A e Depress control again to turn the flashers off FUEL PUMP SHUT OFF SWITCH HEL The fuel pump shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt After a collision if the engine cranks but does not start the fuel pump shut off switch may have been activated 190 Roadside Emergencies The fuel pump shut off switch is located in the passenger s foot well by the kick panel I Use the following procedure to reset the fuel pump shut off switch 1 Tur
71. ake a long period of time for the system to detect an improperly installed fuel filler cap For more information refer to Fuel filler cap in the Maintenance and specifications chapter Check gage Illuminates when the engine coolant CHECK temperature is high the engine oil pressure is low or the fuel gauge is GAGE at or near empty Refer to Engine coolant temperature gauge Engine oil pressure gauge or Fuel gauge in this chapter for more information 11 Instrument Cluster Brake system warning To confirm the brake system BRAKE warning light is functional it will O momentarily illuminate when the ignition is turned to the ON position alternatively for some vehicles when the ignition is moved from the ON position to START position the light will momentarily illuminate prior to reaching the START position It also illuminates if the parking brake is engaged If the brake system warning light does not illuminate as described seek service immediately Illumination after the parking brake is released indicates low brake fluid level or a brake system malfunction and the brake system should be serviced immediately by a qualified technician Refer to Brakes in the Driving chapter for more information Anti lock brake system ABS To confirm the anti lock brake system ABS warning light is functional it will momentarily illuminate when the ignition is turned to the ON position alternatively for some vehicles when the ig
72. all the engine oil filler cap by turning the filler cap clockwise 1 4 of a turn until three clicks are heard or until the cap is fully seated To avoid possible oil loss DO NOT operate the vehicle with the engine oil level indicator and or the engine oil filler cap removed 229 Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark Motorcraft SAE 5W 20 TQUART 0 946L _ SAE 5W 20 engine oil is recommended Only use oils Certified For Gasoline Engines by the American Petroleum Institute API Use Motorcraft or an equivalent oil meeting Ford specification WSS M2C153 H SAE 5W 20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle s engine Do not use supplemental engine oil additives oil treatments or engine treatments They are unnecessary and could under certain conditions lead to engine damage which is not covered by your warranty Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications start up engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specif
73. an discs only with an approved CD cleaner and wipe from the center out to the edge Do not use circular motion 56 Entertainment Systems Cleaning the DVD player Clean the exterior of the DVD player with a damp cloth Do not use CD cleaning kits or CDs intended to clean the interior of your DVD player Use of these products may damage your system CLEANING COMPACT DISCS Inspect all discs for contamination before playing If necessary clean discs only with an approved CD cleaner and wipe from the center out to the edge Do not use circular motion CD AND CD CHANGER CARE e Handle discs by their edges only Never touch the playing surface e Do not expose discs to direct sunlight or heat sources for extended periods of time e Do not insert more than one disc into each slot of the CD changer magazine CD units are designed to play commercially pressed 12 cm 4 75 in audio compact discs only Due to technical incompatibility certain recordable and re recordable compact discs may not function correctly when used in Ford CD players Irregular shaped CDs CDs with a scratch protection film attached and CDs with homemade paper adhesive labels should not be inserted into the CD player The label may peel and cause the CD to become jammed It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels Ball point pens may damage CDs Please contact your dealer for further information
74. an lose traction in slick mud As when you are driving over sand apply the accelerator slowly and avoid spinning your wheels If the vehicle does slide steer in the direction of the slide until you regain control of the vehicle If the transmission transfer case or front axle are submerged in water their fluids should be checked and changed if necessary Water intrusion into the transmission may damage the transmission Refer to Transmission temperature gauge in the Instrument cluster chapter for transmission fluid temperature information If the front or rear axle is submerged in water the axle lubricant should be replaced After driving through mud clean off residue stuck to rotating driveshafts and tires Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components Tread Lightly is an educational program designed to increase public awareness of land use regulations and responsibilities in our nations wilderness areas Ford joins the U S Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by treading lightly 177 Driving Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline you should always try to drive straight up or straight down Avoid driving crosswise or turning on steep slopes o
75. ance at a normal speed Press the REV FWD control again to disengage the reverse advance action and return to normal playback mode 45 Entertainment Systems Enter control The ENTER control allows you to select items when in MENU mode gt gt _enrer Press the ENTER control to select the desired highlighted item CD play mode Press NEXT during CD play to advance to the next track If you press NEXT during the last track the system will wrap around to the first track and begin play Slow play mode To enter slow play mode press the PLAY PAUSE control Once the gt system is in pause mode press the FWD or REV control for slow motion playback Three different speeds are available depending on how long the control is held Press the control once for slow motion playback Press the control again to disengage slow motion playback Press the control a third time to return to normal playback mode User menu mode To adjust the display setting press DISP once and the player menu will os disappear Press DISP again to adjust the display setting Use the arrow controls and the ENTER controls to select the various screen settings Available screen selections are 16x9 Normal 4x3 and Zoom The DVD player will read the disc type and configure the display accordingly Some movies have a wide screen movie format to fit a normal 4x3 screen In this case the movie will have black bars on the
76. and Specifications Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant green colored However not all coolant recycling processes produce coolant that meets Ford specification ESE M97B44 A Use of such coolant may harm the engine and cooling system components Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford approved recycling process is not yet available Used engine coolant should be disposed of in an appropriate manner Follow your community s regulations and standards for recycling and disposing of automotive fluids Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in this chapter Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter Severe climates If you drive in extremely cold climates less than 36 C 34 F e It may be necessary to increase the coolant concentration above 50 e NEVER increase the coolant concentration above 60 e Increased engine coolant concentrations above 60 will decrease the overheat protection characteristics of the engine coolant and may cause engine damage e Refer to the chart on the coolant container to ensure the c
77. applicable exhaust emission standards To make sure that the catalytic converter and other emission control components continue to work properly e Use only the specified fuel listed e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds e Have the items listed in your scheduled maintenance guide performed according to the specified schedule The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system If other than Ford Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Illumination of the Service Engine Soon light charging system warning light or the temperature warning light fluid leaks strange odors smoke or loss of engine power could indicate that the emission control system is not working properly Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment Do not make any unauthorized changes to your vehicle or engine By law vehicle owners and anyon
78. art the engine and take your vehicle to a service facility Driving the vehicle without repairing the engine problem increases the chance of engine damage Take your vehicle to a service facility as soon as possible WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS jf Important safety precautions Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision which may result in possible personal injury Automotive fuels can cause serious injury or death if misused or mishandled 239 Maintenance and Specifications ip Gasoline may contain benzene which is a cancer causing agent Observe the following guidelines when handling automotive fuel Extinguish all smoking materials and any open flames before fueling your vehicle Always turn off the vehicle before fueling Automotive fuels can be harmful or fatal if swallowed Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury If fuel is swallowed call a physician immediately even if no s
79. ation label Consult your dealer for specific weight information e The Federal Communications Commission FCC and Canadian Radio Telecommunications Commission CRTC regulate the use of mobile communications systems such as two way radios telephones and theft alarms that are equipped with radio transmitters Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician e Mobile communications systems may harm the operation of your vehicle particularly if they are not properly designed for automotive use or are not properly installed When operated such systems may cause the engine to stumble or stall or cause the transmission to be damaged or operate improperly In addition such systems may be damaged or their performance may be affected by operating your vehicle Citizens band CB transceivers garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle s operation e Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment 271 Index A ABS see Brakes ccce 161 Accessory delay ccccccccceeeees 88 Air bag supplemental restraint SYSTE 6 scissiveseveancteetnesesecae 143 144 and child safety seats 145 GESCrIPLON erreari e 144 disposal erenisrieaenrn en 148 driver air Dag scisesooseasce
80. ation of the anti lock brake system Never drive with chains on the front tires of 4WD vehicles without also putting them on the rear tires This could cause the rear to slide and swing around during braking Tires Replacement Requirements Do not use a size and type of tire and wheel other than that originally provided by Ford because it can affect the safety and performance of your vehicle which could lead to loss of vehicle control or roll over and serious injury Make sure all tires and wheels on the vehicle are of the same size type tread design brand and load carrying capacity If you have questions regarding tire replacement see an authorized Ford or Lincoln Mercury dealer If you nevertheless decide to equip your 4WD for off road use with tires larger than what Ford recommends you should not use these tires for highway driving 179 Driving If you use any tire wheel combination not recommended by Ford it may adversely affect vehicle handling and could cause steering suspension axle or transfer case failure Do not use aftermarket lift kits or other suspension modifications whether or not they are used with larger tires and wheels These aftermarket lift kits could adversely affect the vehicle s handling characteristics which could lead to loss of vehicle control or roll over and serious injury Tires can be damaged during off road use For your safety tires that are damaged should not be used for
81. ation on the dipstick s normal operating range 262 Maintenance and Specifications LUBRICANT SPECIFICATIONS Ford part name or equivalent High E8TZ 19590 A_ ESA M1C198 A Temperature Spindle bearing 4X4 Front Axle and Wheel Bearing Grease Front axle Motorcraft SAE XY 75W90 TQL WSP M2C201 A 75W 90 Premium 4x4 Front Axle Lubricant Rear axle Motorcraft SAE XY 75W140 QL WSL M2C192 A 75W 140 High Performance Synthetic Rear Axle Lubricant Ford specification Brake fluid Motorcraft High PM 1 ESA M6C25 A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Engine Motorcraft VC 4 A in ESE M97B44 A coolant Gasoline Premium Engine Canada engines Coolant Motorcraft green colored CXC 10 Motorcraft VC 7 A WSS M97B51 Al Premium Gold Engine Coolant yellow colored Engine Refer to your 7 3L Diesel Supplement coolant Diesel engine 263 Maintenance and Specifications Ford part name or equivalent Engine Motorcraft SAE XO 5W20 QSP WSS M2C153 H oil Gasoline 5W 20 Super and API engines Premium Motor Certification Oil Mark Engine oil Diesel Refer to your 7 3L Diesel Supplement engine Hinges latches Multi Purpose XG 4or ESR M1C159 A striker plates Grease F5AZ 19G209 AA fuel filler door hinge and seat tracks Transmission i 1 ESA M1C75 B steering parking Long Life Grease XG 1 K brake linkages and pivots brake pedal shaft Power steering Motorcraft
82. ay For example to load a CD into slot 2 press the LOAD control and then press preset 2 35 Entertainment Systems Auto load This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio a Press and hold the LOAD control until AUTOLOAD is displayed The CD door will open Load the desired disc one at a time The CD is loaded into position and the audio system will display CD Each time the CD door opens INSERT CD is displayed The door will close and the player will move to the next slot after each disc has been loaded The process is repeated until all 6 slots are full The audio system plays the last CD loaded and the display is updated If some slots are already full and autoload is activated the system will fill all empty slots Eject Press the EJ control to stop and eject a CD You can choose which CD will be ejected by pressing the EJ control and the desired preset number 1 6 For example to eject CD 2 press the EJ control and then press the preset 2 control If you do not choose a specific CD the player will eject the current CD If a CD is ejected and not removed from the door of the CD player the player will automatically reload the CD This feature may be used when the ignition is ON or OFF Auto eject Press and momentarily hold the EJ control to engage auto eject All CDs which are present in the player will S be ejected one at a time If a CD is eje
83. band SEEK DOWN will display e Press p to find the next listenable station up the frequency band SEEK UP will display Seek function in CD mode e Press lt q to seek to the previous track of the current disc If the beginning of the disc is reached the CD player seeks to the e Press B gt to seek forward to the next track of the current disc After the last track has been completed the first track of the current disc will automatically replay 30 A gt beginning of the last track on the current disc and begins playing Entertainment Systems Scan function The scan function works in radio or gt CD mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again AM FM select The AM FM select control works in radio and CD modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in CD mode Press this control to stop CD play and begin radio play Radio station memory preset The radio
84. been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and aerodynamic appearance of your vehicle In addition each accessory is made from high quality materials and meets or exceeds Ford s rigorous engineering and safety specifications Ford Motor Company will repair or replace any properly dealer installed Ford accessory found to be defective in factory supplied materials or workmanship during the warranty period as well as any component damaged by the defective accessory The accessory will be warranted for whichever provides you the greatest benefit e 12 months or 20 000 km 12 000 miles whichever occurs first or e The remainder of your new vehicle limited warranty This means that genuine Ford accessories purchased along with your new vehicle and installed by the dealer are covered for the full length of your New Vehicle s Limited Warranty 3 years or 60 000 km 86 000 miles whichever occurs first Contact your dealer for details and a copy of the warranty Not all accessories are available for all models Vehicle Security Styled wheel protector locks Vehicle security systems Underbody Lighting Comfort and convenience Cargo organizers Cargo shades Cargo trays Cell phone holder Dash trim Engine block heaters Battery warmer blanket Cellar phone holder Rear door storage bins Tire step 269 Accessories Travel equipment Adjustable Towing Systems
85. bodily injury OR 216 Customer Assistance 2 Four or more repair attempts are made on the same nonconformity a defect or condition that substantially impairs the use value or safety of the vehicle OR 3 The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days not necessarily all at one time In the case of 1 or 2 above the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE B Dearborn MI 48126 REPORTING SAFETY DEFECTS U S ONLY If you believe that your vehicle has Cann a defect which could cause a crash Gord Motor Company or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 or 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation Washington D C 20590 You can also obtain other information about motor vehicle safety from
86. bol will illuminate E e The Service Engine Soon c indicator light will illuminate If the engine reaches a preset over temperature condition the engine will automatically switch to alternating cylinder operation Each disabled cylinder acts as an air pump and cools the engine When this occurs the vehicle will still operate However e The engine power will be limited e The air conditioning system will be disabled Continued operation will increase the engine temperature and the engine will completely shut down causing steering and braking effort to increase Once the engine temperature cools the engine can be re started Take your vehicle to a service facility as soon as possible to minimize engine damage 238 Maintenance and Specifications When fail safe mode is activated You have limited engine power when in the fail safe mode so drive the vehicle with caution The vehicle will not be able to maintain high speed operation and the engine will run rough Remember that the engine is capable of completely shutting down automatically to prevent engine damage therefore 1 Pull off the road as soon as safely possible and turn off the engine 2 Arrange for the vehicle to be taken to a service facility 3 If this is not possible wait a short period for the engine to cool 4 Check the coolant level and replenish if low Never remove the coolant reservoir cap while the engine is running or hot 5 Re st
87. c module e and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning including the impact sensors the system wiring the air bag system readiness light the air bag back up power and the air bag ignitors Several air bag system components get hot after inflation Do not touch them after inflation If the air bag has deployed the air bag will not function again and must be replaced immediately If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision Determining if the system is operational Af The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system Refer to Air bag readiness section in the Instrument cluster chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness light will either O O flash or stay lit om e The readiness light will not IN illuminate immediately after ignition is turned on e A series of five beeps will be heard The tone pattern will repeat periodically until the problem and or light are repaired If any of these things happen even intermittently have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision
88. ch electrical connections and trailer wheel lug nuts e To aid in engine transmission cooling and A C efficiency during hot weather while stopped in traffic place the gearshift lever in P Park automatic transmission or N Neutral manual transmissions e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels Launching or retrieving a boat When backing down a ramp during boat launching or retrieval e Do not allow the static water level to rise above the bottom edge of the rear bumper e Do not allow waves to break higher than 15 cm 6 inches above the bottom edge of the rear bumper e Disconnect the trailer tow electrical connector to prevent blown fuses caused by water entering into your trailer s electrical wiring Exceeding these limits may allow water to enter critical vehicle components adversely affecting driveability emissions and reliability Replace front and rear axle lubricants any time the axles have been submerged in water Axle lubricant quantities are not to be checked unless a leak is suspected 187 Driving RECREATIONAL TOWING ALL WHEELS ON THE GROUND An example of recreational towing would be towing your vehicle behind a motorhome Follow these guidelines if you have the need for recreational towing your vehicle with all four wheels on the ground These guidelines are designed to ensure that your transmission is not da
89. ch engage Make sure the tongue is latched securely by pulling on it 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 152 Seating and Safety Restraints 7 Pull the lap belt portion across the child seat toward the buckle and R pull up on the shoulder belt while pushing down with your knee on the child seat 8 Allow the safety belt to retract to Kw remove any slack in the belt x gt 9 Before placing the child in the seat forcibly tilt the seat forward and back to make sure the seat is securely held in place To check this grab the seat at the belt path and attempt to move it side to side and forward and back There should be no more than one inch of movement for proper installation A 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine Check to make sure the child seat is properly secured before each use Attaching child safety seats with tether straps Most new forward facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchor
90. ched the seat may cause injury during a sudden stop When reinstalling a rear seat in your vehicle it must be placed in its original position Improper installation of the seat will prevent correct use of the safety belts and could increase the risk of injury Refer to the warning label on the seat belt For proper latching ensure that the floor tubs are clear of debris From the rear of the vehicle with the liftgate open 1 With assistance lift the seat into the rear of the vehicle Roll the seat forward and guide the front locators over the seat locator pins of the front floor tubs e When the rear of the seat is 10 13 cm 4 5 in above the rear pins a seat drop This will ensure that the seat will properly latch into the floor 2 Push up on the seat to verify that it is latched into the floor 3 Verify that the safety belts can move freely on either side of the seat SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips To reduce the risk of injury make sure children sit where they can be properly restrained 130 Seating and Safety Restraints Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision All occupants of the vehicle including the driver should always properly wear their safety belts even when
91. cle is moving can cause some momentary clunk and ratcheting sounds This is the front drivetrain coming up to speed and the automatic locking hubs engaging and is not cause for concern Sand When driving over sand try to keep all four wheels on the most solid area of the trail Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain Apply the accelerator slowly and avoid spinning the wheels If you must reduce the tire pressure for whatever reason in sand make sure you re inflate the tires as soon as possible Avoid excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle Remember you may be able to back out the way you came if you proceed with caution 176 Driving Mud and water If you must drive through high water drive slowly Traction or brake capability may be limited When driving through water determine the depth avoid water higher than the bottom of the hubs Gf possible and proceed slowly If the ignition system gets wet the vehicle may stall Once through water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal Be cautious of sudden changes in vehicle speed or direction when you are driving in mud Even 4WD vehicles c
92. cted and not removed from the door of the CD player the player will automatically reload the CD This feature may be used when the ignition is ON or OFF Shuffle feature Press the SHUF control until the desired shuffle mode is displayed The audio system will then engage the desired shuffle mode 36 Entertainment Systems When engaged the shuffle feature has two different modes SHUFFLE DISC and SHUFFLE TRK SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system SHUFFLE TRK plays all the tracks on the current disc in random order Compression feature The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistent listening level Press the COMP control until COMP ON is displayed Menu mode The MENU control allows you to access many different features within your audio system There are three sets of menus available depending upon which mode or feature is activated While in FM mode two menus are available If RDS is turned OFF you can access the following e SELECT HOURS Refer to Setting the clock e SELECT MINUTES Refer to Setting the clock e RDS OFF Refer to Radio data system feature If RDS is turned ON you can access the following e TRAFFIC ON OFF Refer to Traffic announcements e FIND type Refer to Program type e SHOW NAME TYPE NONE Refer to Radio data system feature e RDS ON Refer to Radi
93. ction if the outside temperature is about 6 C 48 F or higher Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle When AUTO is selected the A C operates automatically for existing conditions and A C will be displayed in the display window If A C is selected while in AUTO operation A C will not be displayed in the display window and the EATC system will remain in AUTO operation However the EATC system will operate without the use of the air conditioning To return to automatic air conditioning operation press AUTO Recirculation control Used to manually enable or disable Ss A the operation of the recirculated air j operation in all modes except QQ s The use of recirculated air when the fn uot i hA air conditioning is operating helps to w JOY reduce the amount of time to cool down the interior of the vehicle in very hot conditions Recirculated air may also help to keep undesired 65 Climate Controls outside odors from reaching the vehicle interior It is recommended to allow the EATC system to automatically control the selection of outside or recirculated air The recirculation control cannot be selected in the WY as interior fogging may occur When AUTO is selected the recirculated air feat
94. d about your vehicle the greater the safety and pleasure you will derive from driving it For more information on Ford Motor Company and its products visit the following website In the United States www ford com In Canada www ford ca In Australia www ford com au In Mexico www ford com mx Additional owner information is given in separate publications This Owner s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle Furthermore due to printing cycles it may describe options before they are generally available Remember to pass on the Owner s Guide when reselling the vehicle It is an integral part of the vehicle Fuel pump shut off switch In the event of an accident the safety switch will automatically cut off the fuel supply to the engine The switch can also be activated through sudden vibration e g collision when parking To reset the switch refer to the Fuel pump shut off switch in the Roadside emergencies chapter Introduction SAFETY AND ENVIRONMENT PROTECTION A Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others your vehicle and its equipment In this guide answers to such questions are contained in comments highlighted by the warning triangle symbol These comments should be read and observed A Warning symbols on your vehicle When you see this symbol i
95. d by the New Vehicle Limited Warranty including maintenance and wear items e alleged personal injury property damage claims e cases currently in litigation e vehicles not used primarily for family personal or household purposes except in states where the Dispute Settlement Board is required to review commercial vehicles e vehicles with non U S warranties Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and in certain states eligibility is dependent upon the customer s possession of the vehicle Eligibility may differ according to state law For example see the unique brochures for California West Virginia Georgia and Wisconsin purchasers lessees Board membership The Board consists of e three consumer representatives 212 Customer Assistance e a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm The dealership Board member is chosen from Ford and Lincoln Mercury dealership management recognized for their business leadership qualities What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form Some states will require you to use certified mail with return receipt requested Your application is reviewed and if it is determined to be eligible
96. d for consistently slippery or loose surfaces e Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle e Be extremely careful when driving on pavement made slippery by loose sand water gravel snow or ice If your vehicle goes off the edge of the pavement e If your vehicle goes off the edge of the pavement slow down but avoid severe brake application Ease the vehicle back onto the pavement only after reducing your speed Do not turn the steering wheel too sharply while returning to the road surface e It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly e It often may be less risky to strike small inanimate objects such as highway reflectors with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or roll over Remember your safety and the safety of others should be your primary concern If your vehicle gets stuck If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear 174 Driving Do not rock the vehicle if the engine is not at normal operating temperature or damage to t
97. d light blinks rapidly for two seconds and then turns to a 100 Driver Controls continuous red proceed with steps 6 through 8 to complete programming of a rolling code equipped device 6 At the garage door opener receiver motor head unit in the garage locate the learn or smart button usually near where the hanging antenna wire is attached to the unit 7 Press and release the learn or smart button The name and color of the button may vary by manufacturer Note There are 30 seconds in which to initiate step eight 8 Return to the vehicle and firmly press hold for two seconds and release the HomeLink button Repeat the press hold release sequence again and depending on the brand of the garage door opener or other rolling code equipped device repeat this sequence a third time to complete the programming HomeLink should now activate your rolling code equipped device To program additional HomeLink buttons begin with step 2 in the Programming section For questions or comments please contact HomeLink at www homelink com or 1 800 355 3515 Gate Operator amp Canadian Programming During programming your hand held transmitter may AT automatically stop transmitting not allowing enough time for HomeLink to accept the signal from the hand held transmitter After completing steps 1 and 2 outlined in the Programming section replace step 3 with the following No
98. de e Press MEM NEXT to listen to the next selection on the tape In CD mode e Press MEM NEXT to listen to the next track on the disc In any mode e Press VOL up or down to adjust the volume Climate control features e Press TEMP up or down to adjust temperature e Press FAN up or down to adjust fan speed TRIP COMPUTER IF EQUIPPED The trip computer tells you about the condition of your vehicle through a constant monitor of vehicle systems You may select display features on the trip computer for a display of status The appearance of your vehicle s trip computer may differ depending on your vehicle s option package but the functions are the same The trip computer only operates with the ignition in the ON position Trip computer features follow 95 Driver Controls Selectable features English metric display Press this control to change the trip computer display between metric and English units Mode control Each press of the MODE control will display a different feature as follows Average fuel economy The display will indicate the vehicle s average fuel economy in liters 100 km or miles gallon since the average fuel economy was last reset If you calculate your average fuel economy by dividing liters of fuel used by 100 kilometers traveled E M RESET C J miles traveled by gallons used your figure may be different than displayed
99. differently than vehicles with a lower center of gravity Utility and four wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low slung sports cars are designed to perform satisfactorily under off road conditions Avoid sharp turns excessive speed and abrupt maneuvers in these vehicles Failure to drive cautiously could result in an increased risk of vehicle rollover personal injury and death Loaded vehicles with a higher center of gravity may handle differently than unloaded vehicles Extra precautions such as slower speeds and increased stopping distance should be taken when driving a heavily loaded vehicle Your vehicle has the capability to haul more cargo and people than most passenger cars Depending upon the type and placement of the load hauling people and cargo may raise the center of gravity of the vehicle Use extra caution while becoming familiar with your vehicle Know the capabilities and limitations of both you as a driver and your vehicle AUTOMATIC TRANSMISSION OPERATION lt Brake shift interlock This vehicle is equipped with a brake shift interlock feature that prevents the gearshift lever from being moved from P Park when the ignition is in the ON position unless brake pedal is depressed 164 Driving If you cannot move the gearshift lever out of P Park with ignition in the ON position and the brake pedal depressed 1 Apply the parking brake turn ig
100. dle and lug wrench On top of the radiator support in the engine compartment Tire change procedure To prevent the vehicle from moving when you change a tire be sure the parking brake is set then block in both directions the wheel that is diagonally opposite other side and end of the vehicle to the tire being changed If the vehicle slips off the jack you or someone else could be seriously injured 1 Park on a level surface activate hazard flashers and set the parking brake 197 Roadside Emergencies 2 Turn engine OFF and block the diagonally opposite wheel block not Q A provided 7 SNS 5 Q 3 Remove the jack jack handle lug k m hie wrench and spare tire from the Oy stowage locations 4 Use the tip of the lug wrench to remove any wheel trim 5 Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is raised off the ground When one of the rear wheels is off the ground the transmission alone will not prevent the vehicle from moving or slipping off the jack even if the transmission is in P Park automatic transmission To prevent the vehicle from moving when you change the tire be sure that the parking brake is set and the diagonally opposite wheel is blocked 6 Insert the hooked end of the jack handle into the jack and use the handle to slide the jack under the vehicle 7 Position the jack according to the following
101. drive with the climate control system in the OFF position e Under normal weather conditions your vehicle s climate control system should be left in any position other than OFF or A when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct e Under snowy or dirty weather conditions your vehicle s climate control system should be left in the OFF position when the vehicle is parked This allows the climate control system to be free from contamination of outside pollutants e If your vehicle has been parked with the windows closed during warm weather conditions the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Once the vehicle has been aired out operate the climate control system as desired e Don t put objects under the front seat that will interfere with the airflow to the rear seats e Remove any snow ice or leaves from the air intake area at the area at the bottom of the windshield and underneath the hood e Do not place objects over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield 68 Climate Controls Avoid placing small objects on top of the instrument panel These objects may fall down into the defroster outlets and block airflow in addition to damaging the clima
102. dvertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter The advertised capacity is the amount of the indicated capacity and the empty reserve combined Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range When refueling your vehicle after the fuel gauge indicates empty you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank For consistent results when filling the fuel tank e Turn the engine ignition switch to the off position prior to refueling an error in the reading will result if the engine is left running e Use the same filling rate setting low medium high each time the tank is filled e Allow no more than 2 automatic click offs when filling e Always use fuel with the recommended octane rating e Use a known quality gasoline preferably a national brand e Use the same side of the same pump and have the vehicle facing the same direction each time you fill up e Have the vehicle loading and distribution the same every time Your results
103. e blades do not use fuel kerosene paint thinner or other solvents Changing the wiper blades To replace the wiper blades 1 Pull the wiper arm away from the windshield and lock into the service position 2 Turn the blade at an angle from the wiper arm Push the lock pin gt manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm 3 Attach the new wiper to the wiper arm and press it into place until a click is heard v v Rear window wiper blade Refer to Windshield wiper blades in this section for more information on rear wiper blades 82 Driver Controls TILT STEERING WHEEL Pull the tilt steering control toward you to move the steering wheel up or down Hold the control while adjusting the wheel to the desired position then release the control to lock the steering wheel in position A Never adjust the steering wheel when the vehicle is moving ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamps 83 Driver Controls OVERHEAD CONSOLE The appearance of your vehicle s overhead console will vary according to your option package Forward storage bin if equipped Press the release control to open the storage compartment The door will open slightly and can be moved to full open The storage compartment may be used to secure sunglasses or a similar object Installin
104. e Press and hold COAST Release the control when the desired speed is reached or Press and release COAST to operate the Tap Down function Each press will decrease the set speed by 1 6 km h 1 mph or Depress the brake pedal When the desired vehicle speed is reached press SET ACCEL To disengage speed control e Depress the brake pedal Disengaging the speed control will not erase the previously programmed set speed Driver Controls SET ACCEL RES SET ACCEL Fl E EL j COAST 93 Driver Controls Pressing OFF will erase the previously programmed set speed SET ACCEL COAST To return to a previously set speed e Press RES RESUME For RES RESUME to operate the vehicle speed must be faster than 48 km h 80 mph SET ACCEL COAST Indicator light This light comes on when either the SET ACCEL or RES controls are CRUISE pressed The vehicle speed must be at or above 48 km h 30 mph It turns off when the speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position 94 Driver Controls STEERING WHEEL CONTROLS IF EQUIPPED These controls allow you to operate some radio and climate control features Radio control features e Press BAND MODE to select AM FM1 FM2 TAPE or CD if equipped In Radio mode e Press MEM NEXT to select a preset station from memory In Tape mo
105. e a factory related vehicle service concern have been unsatisfactory Ford of Canada participates in an impartial third party mediation arbitration program administered by the Canadian Motor Vehicle Arbitration Plan CAMVAP 214 Customer Assistance The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings In the CAMVAP program impartial third party arbitrators conduct hearings at mutually convenient times and places in an informal environment These impartial arbitrators review the positions of the parties make decisions and when appropriate render awards to resolve disputes CAMVAP decisions are fast fair and final the arbitrator s award is binding both to you and Ford of Canada CAMVAP services are available in all territories and provinces For more information without charge or obligation call your CAMVAP Provincial Administrator directly at 1 800 207 0685 GETTING ASSISTANCE OUTSIDE THE U S AND CANADA Before exporting your vehicle to a foreign country contact the appropriate foreign embassy or consulate These officials can inform you of local vehicle registration regulations and where to find unleaded fuel If you cannot find unleaded fuel or can only get fuel with an anti knock index lower than i
106. e appropriate mirror will show a blinking red arrow The arrow provides an additional warning to other drivers that your vehicle is about to turn Driver and passengers seated inside the vehicle cannot see the arrow Fold away mirrors Fold the side mirrors in carefully when driving through a narrow space like an automatic car wash The telescoping feature if equipped allows the mirror to extend approximately 76 mm 8 inches POWER ADJUSTABLE FOOT PEDALS The accelerator and brake pedal should only be adjusted when the A vehicle is stopped and the gearshift lever is in the P Park position Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you The adjustment allows for approximately 76 mm 3 inches of maximum travel Never adjust the accelerator and brake pedal with feet on pedals or while the vehicle is moving 90 Driver Controls SPEED CONTROL To turn speed control on e Press ON Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km h 30 mph Do not shift the gearshift lever into N Neutral with the speed control on Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved To turn speed control off e Press OFF or e Turn off the vehicle ignition Once speed control is switched off the previously programmed set speed will be erased SET ACCEL
107. e ignition in the ON position Displaying outside temperature Press EXT TEMP to display the outside air temperature It will be displayed until EXT TEMP is pressed again auto OFF o C paj OJ If the temperature or fan speed is adjusted or if AUTO or 7 modes are selected while the outside temperature is being displayed the vehicle interior temperature will be displayed for four seconds After four seconds have passed the outside temperature will return to the display window 67 Climate Controls If the outside temperature is displayed while the EATC system is in the OFF mode and then is turned on the outside temperature will return to the display window The outside temperature reading is most accurate when the vehicle is moving Higher readings may be obtained when the vehicle is not moving The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station location Operating tips e In humid weather conditions place the climate control system in QY or rear defrost before driving This will reduce fogging on your windshield Once the windshield has been cleared operate the climate control system as desired e To reduce humidity buildup inside the vehicle in cold weather conditions don t drive with the climate control system in the OFF position or e To reduce humidity buildup inside the vehicle in warm weather conditions don t
108. e located under the seat frame 4 Clip the tether strap to the anchor as shown If the tether strap is clipped incorrectly the child safety seat may not be retained properly in the event of a collision 5 Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat 6 Tighten the child safety seat tether strap according to the manufacturer s instructions If the safety seat is not anchored properly the risk of a child being injured in a collision greatly increases 155 Driving STARTING Positions of the ignition 1 ACCESSORY allows the electrical 4 accessories such as the radio to 3 operate while the engine is not l running AB 2 LOCK locks the steering wheel 2 automatic transmission gearshift lever and allows key removal 7 3 OFF shuts off the engine and all accessories without locking the steering wheel 4 ON all electrical circuits operational Warning lights illuminated Key position when driving 5 START cranks the engine Release the key as soon as the engine starts Preparing to start your vehicle Engine starting is controlled by the powertrain control system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine avoid pre
109. e memory presets in AM FM1 or FM2 In CDDJ mode if equipped press the MEMORY control to select the Entertainment Systems VOLUME MEM lt lt SEEK gt OOD O O COO O 0n o VOLUME MEDIA MEM lt lt SEEK gt CO O O CO O an o next disc in the compact disc changer Play will begin with the first track Seek function The SEEK control has varying functions depending on which mode is enabled VOLUME MEDIA MEM lt lt _SEEK gt COO 0O GC Can a 49 Entertainment Systems In radio mode AM FM1 FM2 Press the 4 control to find the next station down the frequency band Press the control to find the next station up the frequency band In tape mode if equipped press the d control to access the previous selection or for the next selection In CD mode if equipped press the lt control to access the previous track or for the next track In CDDJ mode if equipped press the control to access the previous track or to select the next track of the current disc In AUX DVD mode the SEEK control is not operational Using headphones Personal Audio Feature Single play mode will allow all VOLUME MEDIA MEM lt lt SEEK passengers to listen to the same media source through all speakers COO CO a The Personal Audio Feature allows the front seat passengers to listen to one source radio TAPE CD CDDJ DVD or AUX while the rear seat
110. e of the seat cushion You may wish to discuss the special needs of your child with your pediatrician SAFETY SEATS FOR CHILDREN A Ms Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision 149 Seating and Safety Restraints When installing a child safety seat e Review and follow the information presented in the Azr bag supplemental restraint system SRS section in this chapter e Use the correct safety belt buckle for that seating position the buckle closest to the direction the tongue is coming from Insert the belt tongue into the proper buckle until you hear a snap and feel it latch Make sure the tongue is securely fastened in the buckle e Keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling Place seat back in upright position e Put the safety belt in the automatic locking mode Refer to Automatic locking mode passenger side front and outboard rear seating positions if equipped section in this chapter Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat i
111. e of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AAA BC The traction grades from highest to lowest are AA A B and C The grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Fed
112. e radio frequency signal 1 Press and hold the two outside buttons releasing only when the red ae light begins to flash after 20 seconds Do not repeat step one to O program additional hand held transmitters to the remaining two HomeLink buttons This will erase previously programmed hand held N transmitter signals into HomeLink 2 Position the end of your hand held transmitter 5 14 cm 1 3 inches away from the HomeLink Universal Transceiver surface located on your visor while keeping the red light in view 3 Simultaneously press and hold both the HomeLink and hand held transmitter button Do not release the buttons until step 4 has been completed Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the Gate Operator and Canadian Programming section for Canadian residents 4 The red light will flash slowly and then rapidly Release both buttons when the red light flashes rapidly The rapid flashing light indicates acceptance of the hand held transmitters radio frequency signals 5 Press and hold the just trained HomeLink button and observe the red light If the light is a constant red programming is complete and your device should activate when the HomeLink button is pressed and released Note To program the remaining two HomeLink buttons begin with step 2 in the Programming section do not repeat step 1 If the re
113. e vehicle A To help avoid personal injury always use caution when in reverse and when using the reverse sensing system AN This system is not designed to prevent contact with small or moving objects The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle The system may not detect smaller objects particularly those close to the ground The RSS will assist the driver in detecting certain objects while the vehicle slowly moves in reverse at speeds less than 4 8 km h 3 mph The RSS is not effective at speeds greater than 4 8 km h 8 mph and may not detect certain angular or moving objects 168 Driving The reverse sensing system detects obstacles within approximately 1 8 meters 5 9 ft of the rear bumper with a decreased coverage area at the outer corners of the bumper refer to the figures for approximate zone coverage areas As you move closer to the obstacle the rate of the tone increases When the distance to the obstacle is less than 25 0 cm 10 in the tone will sound continuously If the system detects a stationary or receding object further than 25 0 cm 10 in from the side of the vehicle the tone will sound for only three seconds Once the system detects an object approaching the tone will sound again i The reverse sensing system is poa automatically enabled when the gear selector is placed in R Reverse and the igni
114. e vehicle are combination lap and shoulder belts The front passenger and rear seat outboard safety belts have two types of locking modes described below Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of approximately 8 km h 5 mph or more the combination safety belts will lock to help reduce forward movement of the driver and passengers The safety belt system can also be made to lock manually by quickly pulling on the shoulder belt Automatic locking mode In this mode the shoulder belt is automatically pre locked The belt will still retract to remove any slack in the shoulder belt The automatic locking mode is not available on the driver safety belt 132 Seating and Safety Restraints When to use the automatic locking mode e Any time a child safety seat is installed in a passenger front or outboard rear seating position Gif equipped Children 12 years old and under should be properly restrained in the rear seat whenever possible Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter How to use the automatic locking mode e Buckle the combination lap and shoulder belt e Grasp the shoulder portion and pull downward until the entire belt is
115. e vehicle manually but it takes more effort After any severe impact such as striking large potholes sliding into curbs on icy roads or a collision involving the front end have the front suspension and steering checked for possible damage TRACTION LOK AXLE IF EQUIPPED This axle provides added traction on slippery surfaces particularly when one wheel is on a poor traction surface Under normal conditions the Traction Lok axle functions like a standard rear axle Extended use of other than the manufacturer s specified size tires on a Traction Lok rear axle could result in a permanent reduction in effectiveness This loss of effectiveness does not affect normal driving and should not be noticeable to the driver To reduce the risk of injury never run the engine with one wheel off the ground such as when changing a tire 163 Driving PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles In a rollover crash an unbelted person is significantly more likely to die than a person wearing a seat belt Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances These special design features such as larger tires and increased ground clearance give the vehicle a higher center of gravity than a passenger car Vehicles with a higher center of gravity such as utility and four wheel drive vehicles handle
116. e who manufactures repairs services sells leases trades vehicles or supervises a fleet of vehicles are not 247 Maintenance and Specifications permitted to intentionally remove an emission control device or prevent it from working Information about your vehicle s emission system is on the Vehicle Emission Control Information Decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Please consult your Warranty Guide for complete emission warranty information Readiness for Inspection Maintenance I M testing In some localities it may be a legal requirement to pass an I M test of the on board diagnostics system If your Check Engine Service Engine Soon light is on refer to the description in the Warning lights and chimes section of the Instrument cluster chapter Your vehicle may not pass the I M test with the Check Engine Service Engine Soon light on If the vehicle s powertrain system or its battery has just been serviced the on board diagnostics system is reset to a not ready for I M test condition To ready the on board diagnostics system for I M testing a minimum of 30 minutes of city and highway driving is necessary as described below e First at least 10 minutes of driving on an expressway or highway e Next at least 20 minutes driving in stop and go city type traffic with at least four idle periods Allow the vehicle to sit for at
117. ean the windshield rear window or the wiper blades as damage may occur Clean the outside of the windshield or rear window with a non abrasive cleaner such as Ultra Clear Spray Glass Cleaner E4AZ 19C507 AA available from your authorized Ford Lincoln or Mercury dealer If after cleaning the glass surface the water sheets from the glass e g does not bead then the window is clean The windshield rear window and wiper blades should be cleaned regularly Wiper blades can be cleaned with isopropyl rubbing alcohol 220 Cleaning or windshield washer solution Be sure to replace wiper blades when they appear worn or do not function properly WINDOWS AND WIPER BLADES The windshield rear window and wiper blades should be cleaned regularly If the wiper does not wipe properly substances on the windshield rear window or the wiper blades may be the cause These may include hot wax treatments used by commercial car washes tree sap or other organic contamination To clean these items please follow these tips e The windshield or rear window may be cleaned with a non abrasive cleaner such as Ultra Clear Spray Glass Cleaner E4AZ 19C507 AA available from your dealer e Do not use abrasives as they may cause scratches e Do not use fuel kerosene or paint thinner to clean any parts Wiper blades can be cleaned with isopropyl rubbing alcohol or windshield washer solution Be sure to replace wiper blades when they appear w
118. econd or first gear 167 Driving Shift strategy 4R100 automatic transmission To account for customer driving habits and conditions your 4R100 automatic transmission electronically controls the shift quality by using an adaptive learning strategy The adaptive learning strategy is maintained by power from the battery When the battery is disconnected or a new battery is installed the transmission must relearn its adaptive strategy Optimal shifting will resume within a few hundred kilometers miles of operation If the shift quality does not improve within a few hundred kilometers miles of operation or if the downshifts and other throttle conditions do not function normally see your dealer or a qualified service technician as soon as possible REVERSE SENSING SYSTEM IF EQUIPPED PA The reverse sensing system RSS sounds a tone to warn the driver of obstacles near the rear bumper when the reverse gear is selected To help avoid personal injury please read and understand the limitations on the reverse sensing system described below Reverse sensing is only an assist for some generally large and fixed objects when moving in reverse on a flat surface at parking speeds of approximately 4 8 km h 8 mph or less The weather may also affect the function of RSS RSS may have reduced performance or be activated in inclement weather It is the driver s responsibility for ensuring that their path is clear when operating th
119. econd row seatback Locate the release handle located on the outboard side of the seat cushion and lift gently to allow the seatback to be adjusted to the desired location Reclining the seatback can cause an occupant to slide under the seat s safety belt resulting in severe personal injuries in the event of a collision Third row seat if equipped The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position For information on the proper operation of the safety restraints refer to Safety Restraints in this chapter The third row seat may be removed from the vehicle for additional cargo space Accessing the third row seat Your vehicle is equipped with an easy entry second row seat feature which allows ready access to the third row seat You may enter the third row seat through either rear side door To reduce the risk of personal injury the second row seat should not be left in the forward E Z entry position while the vehicle is in motion Please ensure that the seat is in the upright fully latched rearward position before putting the vehicle in motion Refer to the warning label on the seat side shield 128 Seating and Safety Restraints 1 Rotate the upper seat control rearward while pushing the seatback toward the front of the vehicle 2 Push the seatback toward the front of the vehicle This re
120. econds and try again N 158 Driving 3 If the temperature is below 12 C 10 F and the engine does not start in 15 seconds on the first try turn the key OFF and wait 10 seconds and try again If the engine does not start in two attempts press the accelerator pedal all the way to floor and hold Turn the key to START position 4 When the engine starts release the key then release the accelerator pedal gradually as the engine speeds up 5 After idling for a few seconds apply the brake shift into gear and drive Using the engine block heater if equipped An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defroster system to respond quickly Use of an engine block heater is strongly recommended if you live in a region where temperatures reach 23 C 10 F or below For best results plug the heater in at least three hours before starting the vehicle Using the heater for longer than three hours will not harm the engine so the heater can be plugged in the night before starting the vehicle To prevent electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapters Guarding against exhaust fumes Although odorless and colorless carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects If you ever smell exhaust fu
121. efore following the activation or deactivation procedures make sure that the anti theft system is not armed ignition is off and all vehicle doors liftgate and cargo doors are closed Keyless entry key pad procedure 1 Enter 5 digit entry code Li 2 L 2 Press and hold 7 8 control 3 Press and release 3 4 control 4 Release 7 8 control The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled 5 6 7 8 0 0 Power door unlock lock procedure You must complete steps 1 7 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Turn the ignition key to ON 2 Press the power door unlock control three times 3 Turn the ignition key from ON to OFF 4 Press the power door unlock control three times 5 Turn the ignition back to ON The horn will chirp 6 Press the unlock control then press the lock control The horn will chirp once if autolock was deactivated or twice one short and one long chirp if autolock was activated 7 Turn the ignition to OFF The horn will chirp once to confirm the procedure is complete Pressing the power door UNLOCK LOCK button again will toggle the Autolock Relock states Turn ignition to OFF to exit programming 116 Locks and Security SECURILOCK PASSIVE ANTI THEFT SYSTEM SecuriLock passi
122. ehicle 3 Once the disabled vehicle has been started run both engines for an additional three minutes before disconnecting the jumper cables 204 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected 1 Remove the jumper cable from the grownd metal surface Note In the illustrations lightning bolts are used to designate the assisting boosting battery 2 Remove the jumper cable on the negative connection of the booster vehicle s battery 205 Roadside Emergencies 3 Remove the jumper cable from the positive terminal of the booster vehicle s battery 4 Remove the jumper cable from the positive terminal of the disabled vehicle s battery After the disabled vehicle has been started and the jumper cables removed allow it to idle for several minutes so the engine computer can relearn its idle conditions 206 Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member your roadside assistance center On 4x2 vehicles it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift or a slingbelt with T hooks On 4x4 vehicles it is recommended that your vehicle be towed with a wheel lift or flatbed equipment with all the wheels off the ground H
123. ely implementation of each step in the procedure If two previously programmed coded keys are not available you must bring your vehicle to your dealership to have the spare coded key s programmed Please read and understand the entire procedure before you begin 1 Insert the first previously programmed coded Key into the ignition and turn the ignition from 1 OFF to 3 ON maintain ignition in 3 ON for at least one second but no more than five seconds 2 Turn ignition to 1 OFF then 2 ACC and remove the first coded key from the ignition 3 Within five seconds of removing the first coded key insert the second previously programmed coded key into the ignition and turn the ignition from 1 OFF to 3 ON maintain ignition in 3 ON for at least one second but no more than five seconds 4 Turn the ignition to 1 OFF then 2 ACC and remove the second coded key from the ignition 5 Within 10 seconds of removing the second coded key insert the new unprogrammed key new key valet key into the ignition and turn the ignition from 1 OFF to 3 ON maintain ignition in 3 ON for at least one second but no more than five seconds This step will program your new key to a coded key 6 To program additional new unprogrammed key s repeat this procedure from step 1 If successful the new coded key s will start the vehicle s engine and the theft indicator will illuminate for three seconds and then go out I
124. emblies off the end To adjust the tie downs Use the adjustable tie downs to secure loads to the luggage carrier 106 Driver Controls 1 Completely loosen the slider knobs at each end of the cross rail 2 Lift the cross bar and re set it at the desired position Ensure that both sides of the cross rails are even NOTE Siding the cross bar on the roof can cause damage to the roof paint 3 Tighten the slider knobs at both ends of the cross bar 107 Locks and Security KEYS The key operates all locks on your vehicle In case of loss replacement keys are available from your dealer You should always carry a second key with you in a safe place in case you require it in an emergency Refer to SecuriLock Passive Anti Theft System for more information POWER DOOR LOCKS Press control to unlock all doors Press control to lock all doors Smart locks This feature prevents you from locking yourself out of the vehicle if your key is still in the ignition When you open the driver s door and you lock the vehicle with the power door locks all the doors will lock then the driver s door will automatically unlock reminding you that your key is still in the ignition The vehicle can still be locked with the key in the ignition using the manual lock button on the door locking the driver
125. emoval to prevent dirt or water from entering the reservoir 2 Visually inspect the fluid level 3 If necessary add brake fluid from a clean un opened container until the level reaches MAX Do not fill above this line 4 Use only a DOT 3 brake fluid certified to meet Ford specification ESA M6C25 A Refer to Lubricant specifications in this chapter Brake fluid is toxic If brake fluid contacts the eyes flush eyes with running water for 15 minutes Seek medical attention if irritation persists If taken internally drink water and induce vomiting Seek medical attention immediately If you use a brake fluid that is not DOT 3 you will cause permanent damage to your brakes Do not let the reservoir for the master cylinder run dry This may cause the brakes to fail 250 Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid if equipped Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes Your transmission does not consume fluid However the fluid level should be checked if the transmission is not working properly i e if the transmission slips or shifts slowly or if you notice some sign of fluid leakage Automatic transmission fluid expands when warmed To obtain an accurate fluid check drive the vehicle until it is at normal operating temperature approximately 30 km 20 miles If your vehicle has been
126. en When Hot Avoid Smoking Flames or Sparks Explosive Gas Power Steering Fluid Emission System DEPOSE Passenger Compartment a bd Air Filter pS Check fuel cap Instrument Cluster WARNING LIGHTS AND CHIMES ee ony Q amp gi me atng Q s 40 50 60 2 gt 3 r H S30 Y w 70 ED S 2 4 z H ig RPMX1000 z 20 2 80 2 10 2 99 amp 9160 100 T ol ua on Dnt t x QunDr Bw j S RTO H aa i SELECT RESET JPI P RNO 21 Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs A warning light may iluminate when a problem exists with one of your vehicle s functions Many lights will illuminate when you start your vehicle to make sure the bulb works If any light remains on after starting the vehicle have the respective system inspected immediately Service engine soon Illuminates briefly to ensure the system is functional If it comes on after the engine is started one of the engine s emission control systems may be malfunctioning The light may illuminate without a driveability concern being noted The vehicle will usually be drivable and will not require towing Light turns on solid Temporary malfunctions may cause the light to illuminate Examples are 1 The vehicle has run out of fuel 2 Poor fuel quality or water in the fuel 3 The fuel cap may
127. en the temperature control is anywhere between full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers e Distributes outside or recirculated air through the floor ducts Heating and air conditioning capabilities are provided in this mode The air will be heated or cooled based on the temperature selection KA Distributes outside or recirculated air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode The air will be heated or cooled based on the temperature selection For added customer comfort the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts e CHN Distributes outside air through the windshield defroster ducts This mode can be used to clear ice or fog from the windshield If the outside air is about 6 C 48 F or higher the air conditioner will automatically dehumidify the air to reduce fogging Note that A C will not be displayed in the display window Recirculation and A C override controls cannot be selected For added customer comfort the system will allow some airflow through the floor ducts in this mode Turning the EATC off OFF Outside air is shut out The fan heating and air conditioning will not operate The outside temperature will still display when selected with th
128. eral Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure 256 Maintenance and Specifications SERVICING YOUR TIRES Checking the tire pressure e Use an accurate tire pressure gauge e Check the tire pressure when tires are cold after the vehicle has been parked for at least one hour or has been driven less than 5 km 3 miles e Adjust tire pressure to recommended specifications found on the Certification Label Tire pressure information can also be found on the Tire Information label located on the inside of the fuel filler door Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control Tire rotation Because your vehicle s tires perform different jobs they often wear differently To make sure your tires wear evenly and last longer rotate them as indicated in the scheduled maintenance guide If you notice that the tires wear unevenly have them checked e Four tire rotation N AN K A l I l 257 Maintenance and Specifications e Five tire rotation or A 77k i
129. ers sf Floor Distributes outside air through the floor ducts However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode A Floor and defrost Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts If the temperature is about 6 C 43 F or higher the air conditioner will automatically dehumidify the air to reduce fogging CH Defrost Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the temperature is about 6 C 48 F or higher the air conditioner will automatically dehumidify the air to reduce fogging Operating tips In humid weather conditions place the climate control system in Defrost mode before driving This will reduce fogging on your windshield Once the windshield has been cleared operate the climate control system as desired To reduce humidity buildup inside the vehicle in cold weather conditions don t drive with the climate control system in the OFF or MAX A C position To reduce humidity buildup inside the vehicle in warm weather conditions don t drive with the climate control system in the OFF position 60
130. ext to the vehicle To replace the battery 1 Twist a thin coin between the two halves of the transmitter near the key ring DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART 2 Place the positive side of new battery in the same orientation Refer to the diagram inside the transmitter unit 3 Snap the two halves back together Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle The remote transmitter should operate normally after battery replacement 112 Locks and Security Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle s memory or you would like to purchase additional remote transmitters and have them programmed to your vehicle e Take all your vehicle s transmitters to your dealer for programming or e Perform the programming procedure yourself Programming remote transmitters It is necessary to have all maximum of four original and or new of your remote transmitters available prior to beginning this procedure To program the transmitters yourself e Ensure the vehicle is unlocked e Place the key in the ignition and turn from 2 LOCK to 3 OFF and cycle between 3 OFF and 4 ON eight times in rapid succession within 10 seconds with the eighth turn ending in the 4 ON position The doors will lock to confirm that programming mode has been entered e
131. f not successful the new coded key s will not start the vehicle s engine and the theft indicator will flash on and off and you may repeat steps 1 through 5 If failure repeats bring your vehicle to your dealership to have the new spare key s programmed 119 Seating and Safety Restraints SEATING Full bench seat if equipped e Lift the track release bar to move the seat forward or backward Ensure that the seat is relatched into place 60 40 split bench seat if equipped e Lift the release bar to move the seat forward or backward Ensure the seat is relatched into place e Pull the seatback handle up to recline the seat 120 Seating and Safety Restraints Capiain s chair if equipped Lift the track release bar to move the seat forward or rearward Make sure that the seat is relatched into place Pull the seatback handle up to recline the seat Memory seats and adjustable pedals if equipped This system allows automatic positioning of the driver seat and adjustable pedals to three programmable positions The memory seat control is located on the driver door To program position one move 1 2 the driver seat to the desired position using the seat controls Press the SET control The SET control indicator light will briefly illuminate While the light is illuminated press control 1 e To program position two repeat the previous procedure using control 2 To program position th
132. f the needle goes below the normal range stop the vehicle as soon as safely possible and switch off the engine immediately Check the oil level Add oil if needed refer to Engine oil in the Maintenance and specifications chapter If the oil level is correct have your vehicle checked at your dealership or by a qualified technician 7 gt Transmission fluid temperature gauge If the gauge is in the 4 White area normal the transmission fluid is within the normal operating temperature H between H and C Yellow area warning the transmission fluid is higher than normal operating temperature This can be caused by special operation conditions i e towing or off road use Refer to Special Operating Conditions in the scheduled maintenance guide for instructions Operating the transmission for extended periods of time with the gauge in the yellow area may cause internal transmission damage Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range 16 Instrument Cluster Red area over temperature the transmission fluid is overheating 4 Stop the vehicle to allow the temperature to return to normal range H C If the gauge is operating in the Yellow or Red area stop the vehicle and verify the airflow is not restricted such as snow or debris blocking airflow through the grill If the gauge continues to sho
133. fety belts If the child is the proper size restrain the child in a safety seat Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit 148 Seating and Safety Restraints Do not leave children unreliable adults or pets unattended in your vehicle To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labeled as conforming to all applicable Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child A belt positioning booster seat should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edg
134. ff Press OFF CD EDE Automatic operation Press AUTO and select the desired temperature The selected temperature and the word AUTO will appear in the display window The EATC system will either heat or cool to achieve the selected temperature The system will automatically determine fan speed airflow location and if outside air or recirculated air is required When in AUTO and weather conditions require heat the EATC system directs the majority of the airflow to the floor area The system will allow some airflow through the windshield defroster ducts to reduce window fogging However if the engine is not warm enough to provide heat the fan will be at a low speed and the airflow will be directed to the windshield In approximately 31 2 minutes or less the fan speed will start to increase and the airflow location will change to the floor If unusual conditions exist i e window fogging etc the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary 63 Climate Controls Temperature selection The display window indicates the 4 selected temperature function EXT TEMP AUTO A C G amp D or one of the auto JE OFF I ps D C manual override controls and manual control of fan speed e To control the temperature select any temperature between 16 C 60 F and 32 C 90 F by pres
135. function The seek function control works in radio tape or CD mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency band e Press to find the next listenable station up the frequency band Seek function in tape mode e Press lt q to listen to the previous selection on the tape e Press gt to listen to the next selection on the tape Seek function in CD mode e Press lt Q to seek to the previous track of the disc If a selection has been playing for three seconds or more and you press lt q the CD will replay that selection from the beginning e Press B gt to seek forward to the next track of the disc After the last track has been completed the first track of the current disc will automatically replay 21 Entertainment Systems Scan function ee mes ay works in radio Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the control again to stop the scan mode Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape The tape scans in a forward direction At the end of the tape s first side direction automatically reverses to the opposite side of the tape To stop on a particular selection press the control again Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD
136. g a garage door opener if equipped The storage compartment can be converted to accommodate a variety of aftermarket garage door openers Place Velcro hook onto back side of aftermarket transmitter opposite of actuator control Place transmitter into storage compartment control down Place the provided height adaptors onto the back of the storage bin door as needed e Press the storage compartment door to activate the transmitter 84 Driver Controls Power quarter rear windows if equipped Press the A portion of the VENT control to open the power rear quarter windows Press the y portion of the VENT control to close the power rear quarter windows AUXILIARY POWER POINT 12V Power outlets are designed for accessory plugs only Do not hang any type of accessory or accessory bracket from the plug Improper use of the power outlet can cause damage not covered by your warranty The power point is an additional power source for electrical accessories Do not plug optional electrical accessories into the cigarette lighter Use the powerpoint The maximum current draw of any single power point is 20 Amps Exceeding this limit may result in a blown fuse There are up to four auxiliary power points in the following locations e Located on the instrument panel POWER POINT 85 86 Driver Controls Located on the back side of the center console Accessible from the second row seats
137. guides 198 Roadside Emergencies e Front 4x2 e Front passenger side 4x4 199 Roadside Emergencies e Front driver side 4x4 Make sure the jack fits into the notched area on the differential housing e Rear 8 Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire To lessen the risk of personal injury do not put any part of your body under the vehicle while changing a tire Do not start the engine when your vehicle is on the jack The jack is only meant for changing the tire e Never use the front or rear differential as a jacking point 9 Remove the lug nuts with the lug wrench 10 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall the lug nuts until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered 200 Roadside Emergencies 11 Lower the wheel by turning the jack handle counterclockwise 12 Remove the jack and fully tighten the lug nuts in the order shown 13 Stow the the flat tire jack jack handle and lug wrench Make sure the jack is securely fastened so it does not rattle when driving 14 Unblock the wheels Retighten the lug nuts to the specified torque at 800 km 500 miles after any wheel disturbance rotation flat tire wheel removal etc Bolt size Wheel lug nut torque Lb ft M14 x 2 0 200 225 1
138. he transmission may occur Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat Always set the parking brake fully and make sure the gearshift is latched in P Park Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your dealer or a qualified service technician Do not spin the wheels at over 56 km h 85 mph The tires may fail and injure a passenger or bystander Refer to Transmission temperature gauge in the Instrument cluster chapter for transmission fluid temperature information Emergency maneuvers e In an unavoidable emergency situation where a sudden sharp turn must be made remember to avoid over driving your vehicle i e turn the steering wheel only as rapidly and as far as required to avoid the emergency Excessive steering will result in less vehicle control not more Additionally smooth variations of the accelerator and or brake pedal pressure should be utilized if changes in vehicle speed are called for Avoid abrupt steering acceleration or braking Use all available road surface to return the vehicle to a safe direction of travel e In the event of an emergency stop avoid skidding the tires and do not attempt any sharp steering wheel movements e If the vehic
139. ications for your engine application 230 Maintenance and Specifications BATTERY Your vehicle is equipped with a TZ Q SS Motorcraft maintenance free battery NAN A which normally does not require Alt a y y A additional water during its life of BA JE 2 Sy service yA CET Ef However for severe usage or in high temperature climates check the battery electrolyte level Refer to the scheduled maintenance guide for the service interval schedules Keep the electrolyte level in each cell up to the level indicator Do not overfill the battery cells If the electrolyte level in the battery is low you can add plain tap water to the battery as long as you do not use hard water water with a high mineral or alkali content If possible however try to only fill the battery cells with distilled water If the battery needs water often have the charging system checked If your battery has a cover shield make sure it is reinstalled after the battery has been cleaned or replaced For longer trouble free operation keep the top of the battery clean and dry Also make certain the battery cables are always tightly fastened to the battery terminals If you see any corrosion on the battery or terminals remove the cables from the terminals and clean with a wire brush You can neutralize the acid with a solution of baking soda and water When the battery is disconnected or a new battery installed the trans
140. icient when they are clean because grease and dirt buildup keep the engine warmer than normal When washing Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage Do not spray with cold water to avoid cracking the engine block or other engine components Spray Engine Shampoo and Degreaser F4AZ 19A536 A on all parts that require cleaning and pressure rinse clean Cover the highlighted areas to prevent water damage when cleaning the engine 219 Cleaning K2 opp he gt e e Never wash or rinse the engine while it is running water in the running engine may cause internal damage PLASTIC NON PAINTED EXTERIOR PARTS Use only approved products to clean plastic parts These products are available from your dealer e For routine cleaning use Detail Wash ZC 3 A e If tar or grease spots are present use Extra Strength Tar and Road Oil Removal B7A 19520 AA CLEANING THE WINDSHIELD WIPER BLADES AND REAR WINDOW If the wiper does not wipe properly substances on the windshield rear window or the wiper blades may be the cause These may include hot wax treatments used by commercial car washes tree sap or other organic contamination Do not clean the windshield or rear window glass with abrasives as they may cause scratches Do not use fuel kerosene or paint thinner to cl
141. ile applying light pressure on the brake pedal Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage VEHICLE LOADING Before loading a vehicle familiarize yourself with the following terms e Base Curb Weight Weight of the vehicle including any standard equipment fluids lubricants etc It does not include occupants or aftermarket equipment e Payload Combined maximum allowable weight of cargo occupants and optional equipment The payload equals the gross vehicle weight rating minus base curb weight e GVW Gross Vehicle Weight Base curb weight plus payload weight The GVW is not a limit or a specification 181 Driving e GVWR Gross Vehicle Weight Rating Maximum permissible total weight of the base vehicle occupants optional equipment and cargo The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver s door pillar e GAWR Gross Axle Weight Rating Carrying capacity for each axle system The GAWR is specific to each vehicle and is listed on the Safety Certification Label on the driver s door pillar e GCW Gross Combined Weight The combined weight of the towing vehicle including occupants and cargo and the loaded trailer e GCWR Gross Combined Weight Rating Maximum permissible combined weight of towing vehicle including occupants and cargo and the loaded trailer
142. in the cold fill range as listed on the engine coolant reservoir depending upon application Refer to the Scheduled Maintenance Guide for service interval schedules e Be sure to read and understand Precautions when servicing your vehicle in this chapter If the engine coolant has not been checked at the recommended interval the engine coolant reservoir may become low or empty If the reservoir is low or empty add engine coolant to the reservoir Refer to Adding engine coolant in this chapter Note Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant When adding coolant make sure it is a 50 50 mixture of engine coolant and distilled water Add the mixture to the coolant reservoir when the engine is cool until the appropriate fill level is obtained Do not add engine coolant when the engine is hot Steam and scalding liquids released from a hot cooling system can burn you badly Also you can be burned if you spill coolant on hot engine parts 234 Maintenance and Specifications Do not put engine coolant in the windshield washer fluid container If sprayed on the windshield engine coolant could make it difficult to see through the windshield The cooling system in your vehicle is filled with either green colored Motorcraft Premium Engine Coolant meeting Ford specification ESE M97B4
143. inated and the warning chime is sounding The driver s safety belt is buckled before the ignition switch is turned to the ON position BeltMinder The safety belt warning light illuminates 1 2 minutes and the warning chime sounds 4 8 seconds The safety belt warning light and warning chime turn off The safety belt warning light and indicator chime remain off The BeltMinder feature is a supplemental warning to the safety belt warning function This feature provides additional reminders to the driver that the driver s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster The driver s safety belt is not buckled before the vehicle has reached at least 5 km h 8 mph and 1 2 minutes have elapsed since the ignition switch has been turned to ON The driver s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding The driver s safety belt is buckled before the ignition switch is turned to the ON position The BeltMinder feature is activated the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds repeating for approximately 5 minutes or until safety belt is buckled The BeltMinder feature will not activate The BeltMinder feature will not activate The purpose of the BeltMinder is to remind occasional
144. ing point Tether straps are available as an accessory for many older safety seats Contact the manufacturer of your child seat for information about ordering a tether strap The second row seats of your vehicle are equipped with built in tether strap anchors located behind the seats as described below The tether anchors in your vehicle are along the bottom of the seatback marked with the tether anchor symbol shown with title 153 Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions shown from top view Attach the tether strap only to the appropriate tether anchor as shown The tether strap may not work properly if attached somewhere other than the correct f tether anchor Ge 1 Position the child safety seat on the seat cushion 2 Route the child safety seat tether strap over the back of the seat For vehicles with adjustable head restraints route the tether strap under the head restraint and between the head restraint posts otherwise route the tether strap over the top of the seatback 3 Locate the correct anchor for the selected seating position NA J LJ e Second row Note In the right outboard passenger seating position use only one tether anchor Do not use both 154 Seating and Safety Restraints e Third row 3 e The anchors ar
145. ing the rear control the front control must be in the REAR position 69 Climate Controls Front auxiliary control Your auxiliary A C controls are located in the overhead console Py S 1 P HI 11 COOL WARM PANEL Turn the fan speed control to the desired speed Turn the temperature control to regulate the air temperature Turn the mode selector control to KES determine the airflow location When FLOOR is selected airflow PN will be directed through the floor register in the third row passenger PANEL FLOOR seating When PANEL is selected airflow is directed through the overhead registers of the second and third row seating To blend airflow between each location select any position between PANEL and FLOOR Rear auxiliary climate controls The rear auxiliary climate controls are located in the headliner of the le second row seating To control the g F o auxiliary unit using the rear AY auxiliary climate control the front i auxiliary climate control must be in Gandia 2 Z the REAR position 70 N Climate Controls Turn the fan speed control to the desired speed OFF 4 e Turn the temperature control to regulate the air temperature Turn the mode selector control to determine the airflow location When FLOOR is selected airflow will be directed through the floor register in the third row passenger PANEL FLOOR seating When PANEL is selected airflow
146. is in middle position e the instrument panel dimmer switch is held up until the courtesy lamps come on e any of the remote entry controls are pressed and the ignition is OFF and switch is in the middle position With the ignition key in the ACC or ON position the rear dome lamp can be turned ON or OFF by sliding the control 75 Lights BULBS Replacing exterior bulbs Check the operation of the following lamps frequently e Headlamps e High mount brakelamp e Brakelamps e Turn signal lamps e License plate lamp e Tail lamps e Back up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones If a bulb is removed for an extended period of time contaminants may enter the lamp housings and affect lamp performance Using the right bulbs Replacement bulbs are specified in the chart below Headlamp bulbs must be marked with an authorized D O T for North America and an E for Europe to assure lamp performance light brightness and pattern and safe visibility The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time Function Number of Trade number bulbs Park turn lamp TBST AK Sidemarkerlamp 2 1 Foglamp 899 NID 76 Lights Function Number of Trade number bulbs Third row reading lamp 211 2 All replacement bulbs are clear in color except where noted To replace all instrument
147. is directed through the overhead registers of the second and third row seating To blend airflow between each location select any position between PANEL and FLOOR REAR WINDOW DEFROSTER GJ The rear defroster control is located S on the instrument panel S Press the rear defroster control to P clear the rear window of thin ice and fog e A small LED will illuminate when EA the rear defroster is activated The ignition must be in the ON position to operate the rear window defroster The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position To manually turn off the defroster before 10 minutes have passed push the control again Activating the rear window defroster will also activate the heated mirrors Gf equipped For more information refer to Heated outside mirrors in the Driver controls chapter 71 Lights HEADLAMP CONTROL O Rotate the headlamp control to the To first position to turn on the parking w O ps D lamps Rotate to the second position D zO Y to turn on the headlamps Autolamp control if equipped The autolamp system provides light sensitive automatic on off control of the exterior lights normally controlled by the headlamp control The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to OFF To change the delay time of the autolamp feature do the following 1
148. isk of injury Do not modify the front end of the vehicle Additional equipment may affect the performance of the air bag sensors increasing the risk of injury Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment Children and air bags For additional important safety information read all information on safety restraints in this guide Children must always be properly restrained Accident statistics N suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Failure to follow these instructions may increase the risk of injury in a collision Air bags can kill or injure a child in a child seat NEVER place a rear facing child seat in front of an active air bag If you must use a forward facing child seat in the front seat move the seat all the way back PNN a 145 Seating and Safety Restraints How does the air bag supplemental restraint system work The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Air bags are designed to inflate i
149. ke Fluid 260 Maintenance and Specifications Name Engine coolant Motorcraft Gasoline engines Premium Engine s Coolant green colored or Motorcraft Premium Gold Engine Coolant yellow colored Engine coolant Diesel engine Engine oil includes filter change Gasoline engines Engine oil includes filter change Diesel engine Power steering Motorcraft fluid MERCON ATF Transfer case Motorcraft fluid Gf MERCON ATF equipped Transmission fluid Motorcraft SAE 5W 20 Super Premium Motor Oil Motorcraft MERCON ATF Application Capacity 5 4L V8 engine 25L 26 4 quarts 4 6 8L V10 engine 27 0L 28 5 Refer to your 7 3L Diesel Supplement All Refer to your 7 3L Diesel Supplement gallons Fill to line on dipstick 1 9L 2 0 quarts 4x4 vehicles quarts 4x4 vehicles 16 7L 17 7 quarts 261 Maintenance and Specifications Ford Part Baes Windshield Ultra Clear washer fluid Windshield Washer Concentrate Your vehicle s rear axle is filled with a synthetic lubricant Axle lubricant quantities should not need to be checked unless a leak is suspected service is required or the axle assembly has been submerged in water The axle lubricant should be changed any time the rear axle has been submerged in water 2Add 236 ml 8 oz of Additive Friction Modifier C8AZ 19B546 A or equivalent meeting Ford Specification EST M2C118 A for complete refill of T
150. ker rather than adhesive labels Ball point pens may damage CDs Please contact your dealer for further information 25 Entertainment Systems Rewind The rewind control works in tape and CD modes gt e In tape mode radio play will continue until rewind is stopped with the TAPE control or the beginning of the tape is reached e In CD mode pressing the REW control rewinds the CD within the current track Fast forward The fast forward control works in tape and CD modes q e In the tape mode tape direction will automatically reverse when the end of the tape is reached e In CD mode pressing the control fast forwards the CD within the current track Tape direction select Press to play the alternate side of the tape Eject function Press the EJ control to stop and eject a tape Press the EJ control to stop and eject a CD 26 Entertainment Systems Dolby noise reduction Dolby noise reduction operates in tape mode Dolby noise reduction __ __ __ gt reduces the amount of hiss and static during tape playback Press the BO control to activate and deactivate the Dolby noise reduction Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol D0 are registered trademarks of Dolby Laboratories Licensing Corporation Compression adjust Compression adjust brings soft and loud CD pas
151. l battery terminals and remove any excessive corrosion before you attach the battery cables Ensure that vent caps are tight and level 5 Turn the heater fan on in both vehicles to protect any electrical surges Turn all other accessories off Connecting the jumper cables 1 Connect the positive booster cable to the positive terminal of the discharged battery Note In the illustrations lightning bolts are used to designate the assisting boosting battery 202 Roadside Emergencies 2 Connect the other end of the positive cable to the positive terminal of the assisting battery 3 Connect the negative cable to the negative terminal of the assisting battery 203 Roadside Emergencies 4 Make the final connection of the negative cable to an exposed metal part of the stalled vehicle s engine away from the battery and the carburetor fuel injection system Do not use fuel lines engine rocker covers or the intake manifold as grownding points Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery 5 Ensure that the cables are clear of fan blades belts moving parts of both engines or any fuel delivery system parts Jump starting 1 Start the engine of the booster vehicle and run the engine at moderately increased speed 2 Start the engine of the disabled v
152. l to access the batteries The remote control unit uses two f AAA batteries Rear seat controls The DVD system controls allow the VOLUME MEDIA MEM lt lt SEEK amp rear seat passengers to operate the COO COO radio tape CD DVD or CD DJ if equipped gt Q ah o Press the f control to activate the rear controls A will appear in the radio display Adjusting the volume from the rear seat controls The volume control allows the rear seat passengers to adjust the VOLUME MEDIA MEM lt lt SEEK gt i level of the desired v cern i O e aesire COO O CO OQO an o Press the control to increase the volume Press the control to decrease the volume When in single play mode the speaker volume cannot be set higher than the current volume radio setting When in headphone mode the rear seat controls can change the volume setting to any desired level 48 Mode select Press the control to toggle between AM FM1 FM2 TAPE CD CDDJ DVD and AUX modes if equipped When selected the media source will illuminate in the radio display e AM AM radio frequency band e FMI FM2 FM radio frequency bands e TAPE cassette tape if equipped e CD single cd player if equipped e CDDJ compact disc changer if equipped e DVD AUX DVD player Auxiliary line input Memory preset control In radio mode press the MEMORY control successively to scroll through th
153. lash to pass Pull toward you slightly to activate and release to deactivate 73 Lights Use to adjust the brightness of the instrument panel during headlamp and parklamp operation e Rotate up to brighten e Rotate down to dim Rotate to full up position past detent dome defeat to turn on interior lamps Rotate to full down position past detent dome defeat to turn off interior lamps AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician TURN SIGNAL CONTROL amp o gt e Push down to activate the left turn signal e Push up to activate the right turn signal A i INTERIOR LAMPS Dome Map lamps if equipped The map lamps and controls are located on the dome lamp Press the controls on either side of each map lamp to activate the lamps 74 Lights Rear courtesy reading lamps e Second row courtesy reading lamp e Third row courtesy reading lamp The courtesy lamps light when e any door is opened e the instrument panel dimmer switch is held up until the courtesy lamps come on e any of the remote entry controls are pressed and the ignition is OFF The reading lamps can be turned on by pressing the rocker control Rear dome lamp The dome lamp lights when e any door is opened and switch
154. le goes from one type of surface to another i e from concrete to gravel there will be a change in the way the vehicle responds to a maneuver steering acceleration or braking Again avoid these abrupt inputs Parking On some 4WD vehicles when the transfer case is in the N Neutral position the engine and transmission are disconnected from the rest of 175 Driving the driveline Therefore the vehicle is free to roll even if the automatic transmission is in P Park or the manual transmission is in gear Do not leave the vehicle unattended with the transfer case in N Neutral position Always set the parking brake fully and turn off the ignition when leaving the vehicle 4WD Systems 4WD when you select a 4WD mode uses all four wheels to power the vehicle This increases traction enabling you to drive over terrain and road conditions that a conventional two wheel drive vehicle can t Power is supplied to all four wheels through a transfer case On 4WD vehicles the transfer case allows you to select 4WD when necessary Information on transfer case operation and shifting procedures can be found in the Driving chapter Information on transfer case maintenance can be found in the Maintenance and specifications chapter You should become thoroughly familiar with this information before you operate your vehicle Normal characteristics On some 4WD models the initial shift from two wheel drive to 4x4 while the vehi
155. le has a seat belt system with an energy management feature at the front outboard seating position to help further reduce the risk of injury in the event of a head on collision The front outboard seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner This feature is designed to help reduce the belt force acting on the occupant s chest 134 Seating and Safety Restraints Safety belt replacement label The short plastic boot on the front safety belt at the passenger outboard anchor location covers a Replace Belt label on the safety belt uM Z In the event of a collision the colored label REPLACE BELT may become visible If this occurs the safety belt must be replaced Whenever the yellow portion of the label is visible the safety belt must be replaced A _ CAUTION 135 Seating and Safety Restraints Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury Safety belt pretensioner if equipped Your vehicle is equipped with safety belt pretensioners at the driver and front outboard passenger seating positions The Seat Integrated Restraints SIR seat is equipped with a buckle pretensioner Do NOT place objects between the seats this could interfere with the functioning of the pretensioner The safety belt pretensioners are designed to activate onl
156. leases the seat track and the seat will move forward 3 After entering the 3rd row seat pull back the 2nd row seatback until it latches at full rearward position This will latch and lock the seatback and the seat track Insure the seat is pulled back to the locked position whether the seat is occupied or empty If not latched the seat may cause injury during a sudden stop Folding down the third row seat Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion The seatback will latch into place Pull the seat release lever to return the seatback into the upright seating position LD LJ gt a WSs ZAA N Removing the third row seat From the rear of the vehicle with the liftgate window and cargo doors open 1 Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down onto the seat cushion e The seatback will latch onto the cushion 2 Lift the seat release bar located at the center of the seat near the floor to release the floor latches 129 Seating and Safety Restraints 3 While pulling up on the release bar lift the seat up and out of the floor tubs and roll seat rearward 4 With assistance lift the seat out of the vehicle Installing the third row seat Always latch the vehicle seat to the floor whether the seat is occupied or empty If not lat
157. leather seating surfaces have a clear protective coating over the leather e To clean use a soft cloth with Deluxe Leather and Vinyl Cleaner F2AZ 19521 WA Dry the area with a soft cloth e To help maintain its resiliency and color use the Deluxe Leather Care Kit F8AZ 19G253 AA available from your authorized dealer e Do not use household cleaning products alcohol solutions solvents or cleaners intended for rubber vinyl and plastics or oil petroleum based leather conditioners These products may cause premature wearing of the clear protective coating UNDERBODY Flush the complete underside of your vehicle frequently Keep body and door drain holes free from packed dirt 222 Cleaning FORD LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes These quality products have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and appearance of your vehicle Each product is made from high quality materials that meet or exceed rigid specifications For best results use the following or products of equivalent quality Ford Custom Clearcoat Polish Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant not available in Canada Motorcraft Vinyl Conditioner Canada only Ford Deluxe Leather and Vinyl Cleaner not available in Canada Motorcraft Vinyl
158. local authorized recycling center to find out more about recycling automotive batteries RECYCLE ENGINE COOLANT E Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide The coolant concentration should be maintained at 50 50 coolant and water which equates to a freeze point of 36 C 34 F Coolant concentration testing is possible with a hydrometer or antifreeze tester such as the Rotunda Battery and Antifreeze Tester 014 R1060 The level of coolant should be maintained at the cold full of cold fill range level in the coolant reservoir If the level falls below add coolant per the instructions in the Adding engine coolant section Your vehicle was factory filled with a 50 50 engine coolant and water concentration If the concentration of coolant falls below 40 or above 60 the engine parts could become damaged or not work properly A 50 50 mixture of coolant and water provides the following e Freeze protection down to 36 C 34 F e Boiling protection up to 129 C 265 F e Protection against rust and other forms of corrosion e Enables calibrated gauges to work properly 233 Maintenance and Specifications When the engine is cold check the level of the engine coolant in the reservoir COLD FILL RANGE MIN e The engine coolant should be at the cold fill level or with
159. locks and home or office lighting When programming your HomeLink Universal Transceiver to a garage door or gate be sure that people and objects are out of the way to prevent potential harm or damage Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by U S federal safety standards this includes any garage door opener model manufactured before April 1 1982 A garage door which cannot detect an object signaling the door to stop and reverse does not meet current U S federal safety standards For more information contact HomeLink at www homelink com or 1 800 355 3515 Retain the original transmitter for use in other vehicles as well as for future programming procedures i e new HomeLink equipped vehicle purchase It is also suggested that upon the sale of the vehicle the programmed Homelink Universal Transceiver buttons be erased for security purposes refer to Programming in this section 99 Driver Controls Programming Do not program the HomeLink Universal Transceiver with the vehicle parked in the garage Note Some vehicles may require the ignition switch to be turned to the second or ACC position for programming and or operation of the HomeLink It is also recommended that a new battery be placed in the hand held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of th
160. lustration depicts the advantage of an ABS equipped vehicle on bottom to a non ABS equipped vehicle on top during hard braking with loss of front braking traction Using ABS e In an emergency or when maximum efficiency from the four wheel ABS is required apply continuous force on the brake The four wheel ABS will be activated immediately thus allowing you to retain full steering control of your vehicle and providing there is sufficient space will enable you to avoid obstacles and bring the vehicle to a controlled stop e The anti lock system does not reduce stopping distance Always leave enough room between your vehicle and the vehicle in front of you to stop e We recommend that you familiarize yourself with this braking technique However avoid taking any unnecessary risks ABS warning lamp s The 3 warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position If the light does not illuminate momentarily at start up remains on or continues to flash the ABS needs to be serviced 161 Driving With the ABS light on the anti lock brake system is disabled and normal BRAKE braking is still effective unless the D brake warning light also remains illuminated with parking brake released If your brake warning lamp illuminates have your vehicle serviced immediately Parking brake P Apply the parking brake whenever the vehicle is parked To set the parki
161. ly Do not pump the brakes 178 Driving Driving on snow and ice AWD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle Should you start to slide while driving on snowy or icy roads turn the steering wheel in the direction of the slide until you regain control Avoid sudden applications of power and quick changes of direction on snow and ice Apply the accelerator slowly and steadily when starting from a full stop Avoid sudden braking as well Although a 4WD vehicle may accelerate better than a two wheel drive vehicle in snow and ice it won t stop any faster because as in other vehicles braking occurs at all four wheels Do not become overconfident as to road conditions Make sure you allow sufficient distance between you and other vehicles for stopping as well as drive slower than usual and consider using one of the lower gears In emergency stopping situations avoid locking of the wheels Use a squeeze technique push on the brake pedal with a steadily increasing force which allows the wheels to brake yet continue to roll so that you may steer in the direction you want to travel If you lock the wheels release the brake pedal and repeat the squeeze technique If your vehicle is equipped with a Four Wheel Anti Lock Brake System ABS apply the brake steadily Do not pump the brakes Refer to the Brakes section of this chapter for additional information on the oper
162. m inspected immediately Headlamps on warning chime Sounds when the headlamps or parking lamps are on the key is removed from the ignition and the driver s door is opened 14 Instrument Cluster Key in ignition warning chime Sounds when the key is left in the ignition and the driver s door is opened Parking brake ON warning chime Sounds when the parking brake is set the engine is running and the vehicle is driven more than 5 Km 8 mph GAUGES I P RNO21 OT g Engine coolant temperature gauge Indicates the temperature of the engine coolant At normal operating temperature the needle remains within the normal area the area between the H and C If it enters the red section the engine is overheating Stop the vehicle as soon as safely possible switch off the engine immediately and let the engine cool Refer to Engine coolant in the Maintenance and specifications chapter A Never remove the coolant reservoir cap while the engine is running or hot Steam and scalding liquid from a hot cooling system can burn you badly This gauge indicates the temperature of the engine coolant not the coolant level If the coolant is not at its proper level the gauge indication will not be accurate 15 Instrument Cluster Engine oil pressure gauge Indicates engine oil pressure At normal operating temperature the needle will be in the normal range the area between the L and H i
163. maged 2WD vehicles with automatic transmissions e Place the transmission in N Neutral e Maximum speed is 56 km 35 mph e Maximum distance is 80 km 50 miles If a distance of 80 km 50 miles or a speed of 56 km 85 mph must be exceeded the drive shaft will have to be removed before the vehicle is towed Ford recommends the driveshaft be removed installed only by a qualified technician See your local dealer for driveshaft removal installation Improper removal installation of the driveshaft can cause transmission fluid loss damage to the driveshaft and internal transmission components 4WD vehicles electronic shift transfer case with automatic transmissions 4x4 vehicles with electronic shift on the fly cannot be towed with any wheels on the ground 188 Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern Ford Motor Company offers a complimentary roadside assistance program This program is separate from the New Vehicle Limited Warranty The service is available e 24 hours seven days a week e for the New Vehicle Limited Warranty period of three years or 60 000 km 86 000 miles whichever occurs first on Ford and Mercury vehicles and four years or 80 000 km 50 000 miles on Lincoln vehicles Roadside assistance will cover e changing a flat tire jump starts lock out assistance limited fuel delivery towing of your disabled vehicle to the nea
164. me is from level 1 through level 3 Level 0 turns the speed sensitive volume off and level 7 is the maximum setting To engage the speed sensitive volume feature press and hold the volume control for five seconds VOL with the radio on then press PUSH ON A A to increase volume A compensation v to decrease or shut off the SEL volume compensation y The selected level will appear in the display Bass adjust The bass adjust control allows you to increase or decrease the audio system s bass output SEL Press the BASS control Use the v SEL control to increase or decrease the amount of bass Treble adjust The treble adjust control allows you A to increase or decrease the audio system s treble output SEL Press the TREB control Use the v SEL control to increase or decrease the amount of treble 29 Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Press the BAL control Use the SEL control to adjust the sound between the left and right speakers Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Press the FADE control Use the SEL control to adjust the sound between the front and rear speakers Seek function The seek function works in radio or CD mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency
165. mes of any kind inside your vehicle have your dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you 159 Driving Have the exhaust and body ventilation systems checked whenever e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision WARNING Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm In addition certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time open the windows at least 2 5 cm one inch Adjust the heating or air conditioning if equipped to bring in fresh air Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris BRAKES Your service brakes are self adjusting Refer to the scheduled maintenance guide for scheduled maintenance Occasional brake noise is normal and often does not indicate a performance concern with the vehicle s brake system In normal operation automotive brake systems may emit occasional o
166. mission must learn its adaptive strategy As a result of this the transmission may shift firmly This operation is considered normal and will fully update transmission operation to its optimum shift feel Batteries normally produce explosive gases which can cause personal injury Therefore do not allow flames sparks or lighted substances to come near the battery When working near the battery always shield your face and protect your eyes Always provide proper ventilation 231 Maintenance and Specifications When lifting a plastic cased battery excessive pressure on the end walls could cause acid to flow through the vent caps resulting in personal injury and or damage to the vehicle or battery Lift the battery with a battery carrier or with your hands on opposite corners Keep batteries out of reach of children Batteries contain sulfuric acid Avoid contact with skin eyes or clothing Shield your eyes when working near the battery to protect against possible splashing of acid solution In case of acid contact with skin or eyes flush immediately with water for a minimum of 15 minutes and get prompt medical attention If acid is swallowed call a physician immediately Battery posts terminals and related accessories contain lead and lead compunds Wash hands after handling For information on transmission operation after the battery has been disconnected see Shift strategy in the driving section Because your vehicle
167. n FCC Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference and radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to consult the dealer or an experienced radio TV technician for help 55 Entertainment Systems Care and service of the DVD player Environmental extremes DVD players which are subjected to harsh environmental conditions may be damaged or perform at less than maximum capability To avoid these outcomes whenever possible avoid exposing your DVD player to e extremely hot or cold temperatures e direct sunlight e high humidity e a dusty environment e locations where strong magnetic fields are generated Temperatur e extremes When the vehicle is parked under direct sunlight or in an extremely cold
168. n Rear axle ratio Maximum Maximum GCWR kg lbs trailer weight kg lbs Maximum Maximum GCWR kg lbs trailer weight kg lbs Driving The frame mounted hitch receiver is non removable Towing a Class IV trailer extra heavy duty 2 268 4 536 kg 5 001 10 000 lbs trailer weight requires a weight distributing or fifth wheel hitch Do not exceed the GVWR or the GAWR specified on the certification label Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage transmission axle damage structural damage loss of control and personal injury Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Load equalizing hitch When hooking up a trailer using a load equalizing hitch always use the following procedure 1 Park the unloaded vehicle on a level surface With the ignition on and all doors closed allow the vehicle to stand for several minutes so that it can level 2 Measure the height of a reference point on the front and rear bumpers at the center of the vehicle 3 Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0 13 mm 0 5 in of the reference point After proper adjustment the rear bumper should be no higher than in Step 2 Adjusting an equalizing hitch so the rear
169. n a seating position which is capable of providing a tether anchorage For more information on top tether straps refer to Attaching child safety seats with tether straps in this chapter Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision 150 Seating and Safety Restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat NEVER place a rear facing child seat in front of an active air bag If you must use a forward facing child seat in the front seat move the seat all the way back 1 Position the child safety seat in a seat with a combination lap and shoulder belt Children 12 and under should be properly restrained in the rear seat whenever possible 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 151 Seating and Safety Restraints 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted A 4 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming from for that seating position until you hear a snap and feel the lat
170. n frontal and near frontal collisions not rollover side impact or rear impacts unless the collision causes sufficient longitudinal deceleration The air bags inflate and deflate rapidly upon activation After air bag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum powder to lubricate the bag or sodium compounds e g baking soda that result from the combustion process that inflates the air bag Small amounts of sodium hydroxide may be present which may irritate the skin and eyes but none of the residue is toxic While the system is designed to help reduce serious injuries contact with a deploying air bag may also cause abrasions swelling or temporary hearing loss Because air bags must inflate rapidly and with considerable force there is the risk of death or serious injuries such as fractures facial and eye injuries or internal injuries particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment Thus it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control 146 Seating and Safety Restraints The SRS consists of e driver and passenger air bag modules which include the inflators and air bags e one or more impact and safing sensors e a readiness light and tone e a diagnosti
171. n refer to the Automatic Transmission Operation section of the Driving chapter 103 Driver Controls CENTER CONSOLE Your vehicle may be equipped with a variety of console features These include e Utility compartment e Coin holder slots e Pen holder Use only soft cups in the cupholder Hard objects can injure you in a collision e Utility compartment e Coin holder e Pen holder e Writing surface e Space for lap top computer 104 Driver Controls CARGO NET IF EQUIPPED The cargo net secures lightweight BRR objects in the cargo area Attach the as TTS i j 7A net to the anchors provided This Ps net is not designed to restrain objects during a collision TRIDOOR The TriDoor area is intended for cargo storage only not for passengers You can open and close the TriDoors from outside the vehicle only You cannot open the liftgate or cargo doors from inside the vehicle e To open the liftgate unlock the liftgate with the key the key fob by pressing the UNLOCK button twice or power door locks and pull up on the liftgate handle To open the cargo doors open the liftgate then open right cargo door first using the handle on top of the door then open the left cargo door using the handle on the side of the door For wider loads the cargo doors can be opened wider by unhooking the check straps from the door hinge Make sure the check straps are reattached after l
172. n the VOLUME MEDIA MEM lt SEEK gt frequency band COO QO OGO e Press gt to find the next O O lt a listenable station up the frequency band 42 Entertainment Systems In tape mode use the SEEK function to access the next gt or previous lt q selection In CD or CD changer mode Gf equipped use the SEEK function to access the next gt or the previous lt q selection DVD REAR SEAT ENTERTAINMENT SYSTEM IF EQUIPPED Your vehicle may be equipped with a Family Entertainment System FES which allows you to watch CD Roms DVDs and to plug in and play a variety of standard video games Please review this user manual to become familiar with the FES features and controls as well as the very important safety information DVD player controls 1 MAIN control NEXT Press to access the next track on the CD the next chapter on the DVD or to go up in cursor mode e PREV Press to access the previous track on the CD the previous chapter on the DVD or to go down in cursor mode e REV Press to reverse in CD and DVD play modes or to move the cursor left in the menu active mode e FWD Press to advance in CD and DVD play modes or to move the cursor right in the menu active mode 43 Entertainment Systems 2 PLAY PAUSE control Press to playback or pause the DVD 3 DIM control Adjust to increase or decrease the amount of brightness on the screen 4 ENTER control Pres
173. n the engine off and wait a few minutes for the oil to drain into the oil pan 3 Set the parking brake and ensure the gearshift is securely latched in P Park 4 Open the hood Protect yourself from engine heat 5 Locate and carefully remove the engine oil level indicator dipstick 4 ah 1 g D N 22 G LIIITE PO C RISE oman 6 Wipe the indicator clean Insert the indicator fully then remove it again e If the oil level is between the MIN and MAX marks the oil level is acceptable DO NOT ADD OIL 228 Maintenance and Specifications e If the oil level is below the MIN mark add enough oil to raise the level within the MIN MAX range e Oil levels above the MAX mark may cause engine damage Some oil must be removed from the engine by a service technician 7 Put the indicator back in and ensure it is fully seated Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine owl in this chapter 2 If the engine oil level is not within the normal range add only certified engine oil of the recommended viscosity Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening 3 Recheck the engine oil level Make sure the oil level is not above the MAX mark on the engine oil level indicator dipstick 4 Install the indicator and ensure it is fully seated 5 Fully inst
174. n the ignition to the OFF position 2 Check the fuel system for leaks 3 If no fuel leak is apparent reset the fuel pump shut off switch by pushing in on the reset button 4 Turn the ignition to the ON position Pause for a few seconds and return the key to the OFF position 5 Make a further check for leaks in the fuel system FUSES AND RELAYS Fuses If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire within the fuse Check the appropriate fuses before replacing any electrical components 191 Roadside Emergencies Note Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire Standard fuse amperage rating and color COLOR Fuse Mini Standard Maxi Carimi ge Fuse link maxi rating fuses fuses fuses n cartridge a Grey Grey sa Violet Violet a Pink Pink sa Tan Tan _ rsa Brown Brown _ TA Red ra A Bme Blue 20A 25A Natural Natural 30A aa o onge Green Green sa Ra Red Rea 60a Blue Yellow _ TOA tan Brown_ sa Natural Black Passenger compartment fuse panel
175. ncluding the driver should always properly wear their safety belts even when an air bag SRS is provided Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints National Highway Traffic Safety Administration NHTSA recommends a minimum distance of at least 25 cm 10 inches between an occupant s chest and the driver air bag module Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries Steps you can take to properly position yourself away from the air bag e Move your seat to the rear as far as you can while still reaching the pedals comfortably e Recline the seat slightly one or two degrees from the upright position Do not put anything on or over the air bag module Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury 144 Seating and Safety Restraints Do not attempt to service repair or modify the air bag supplemental restraint systems or its fuses See your Ford or Lincoln Mercury dealer The front passenger air bag is not designed to offer protection to an occupant in the center front seating position Modifications to the front end of the vehicle including frame bumper front end body structure and tow hooks may affect the performance of the air bag sensors increasing the r
176. nditions while you are using fuel with the recommended octane rating see your dealer or a qualified service technician to prevent any engine damage Fuel quality If you are experiencing starting rough idle or hesitation driveability problems during a cold start try a different brand of Regular unleaded gasoline Premium unleaded gasoline is not recommended particularly in the United States because it may cause these problems to become more pronounced If the problems persist see your dealer or a qualified service technician It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating Aftermarket products could cause damage to the fuel system Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty 242 Maintenance and Specifications Many of the world s automakers Gan issued the World wide Fuel Charter iY that recommends gasoline iV specifications to provide improved eave performance and emission control system protection for your vehicle Gasolines that meet the World wide Fuel Charter should be used when available Ask your fuel supplier about gasolines that meet the World wide Fuel Charter In Canada look for fuels that display the Auto Makers Choice logo Cleaner air Ford endorses the use of reformulated cleaner burning gasolines to improve air
177. ng back to the clock In media mode the media information will always be displayed 24 Entertainment Systems Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt q to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Tape CD select e To begin tape play with a tape loaded into the audio system while in the radio or CD mode press the TAPE control Press the button during rewind or fast forward to stop the rewind or fast forward function To begin CD play Gf CD is loaded press the CD control The first track of the disc will begin playing If returning from radio or tape mode CD play will begin where it stopped last CD units are designed to play commercially pressed 12 cm 4 75 in audio compact discs only Due to technical incompatibility certain recordable and re recordable compact discs may not function correctly when used in Ford CD players Irregular shaped CDs CDs with a scratch protection film attached and CDs with homemade paper adhesive labels should not be inserted into the CD player The label may peel and cause the CD to become jammed It is recommended that homemade CDs be identified with permanent felt tip mar
178. ng brake press the parking brake pedal down until the pedal stops The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated when the ignition is turned ON until the parking brake is released Always set the parking brake fully and make sure that the gearshift is securely latched in P Park automatic transmission or in 1 First manual transmission The parking brake is not recommended to stop a moving vehicle However if the normal brakes fail the parking brake can be used to stop your vehicle in an emergency Since the parking brake applies only the rear brakes the vehicle s stopping distance will increase greatly and the handling of your vehicle will be adversely affected 162 Driving Pull the release lever to release the brake Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy STEERING YOUR VEHICLE Your vehicle is equipped with power steering Power steering uses energy from the engine to help steer the vehicle Never hold the steering wheel to the extreme right or the extreme left position for more than a few seconds when the engine is running This action could damage the power steering pump If the amount of effort needed to steer your vehicle changes at a constant vehicle speed have the power steering system checked If the power steering system breaks down or if the engine is turned off you can steer th
179. ning the safety belts 142 extension assembly 6 142 for adults sssrssiisressssnar 132 134 for CHIEN sisi sscsiccrcessessssessncets 148 WA peli xzesssevincssdtenenesicctestsytetis 137 warning light and CHIME kirsaiscssrirensss 12 14 138 139 Safety seats for children 149 Seat belts see Safety restraints 130 OAS okes EA rrn EDSEL 120 child safety seats 0000n00000 149 MEMOTLY SEAT oo ceeeeeeceeeeeeeeeeeee 121 SecuriLock passive anti theft SYSTE beciss ccnsdeaboaseacasecsaecens 117 118 Servicing your vehicle 225 SNOWDPIOWING ou eeeeeeeeeeeeteeeeeeees 7 Spare tire see Changing the Tire 196 Spark plugs specifications 260 265 266 Special notice diesel powered vehicles 6 utility type vehicles 00 T Specification chart TUDYICAINES iresi iensen 263 265 Speed control 0 0 eeeeeeeeeeeee 91 Speedometer ccccccccssesceeeees 17 Starting your vehicle 156 158 Jump starting eee 201 DUCCIING arire au a EE 163 Steering wheel CONTOlS sisis 83 91 95 IGNE doirasi 83 T Tachometer ccccccccseccecsssseeeeenes 18 ANa T ARTAN EEEE E EE 196 255 257 Changing eee 196 197 checking the pressure 257 replacing fo yeseveescendavsegsesesedsesscers 258 TOUAUING AA VAEA E 257 snow tires and chains 259 UTE SPACES scdecsccgdcssinsdsnsnaseacteds 256 treadwear cceccec
180. nition is moved from the ON position to the START position the light will momentarily illuminate just prior to reaching the START position If the light remains on continues to flash or fails to illuminate have the ABS serviced immediately If the ABS light remains on it means the anti lock brake system has malfunctioned and is disabled however the normal brake system will still function unless the brake warning light also remains illuminated and parking brake is off Refer to Brakes in the Driving chapter for more information Safety belt Illuminates to remind you to fasten your safety belts For more information refer to the Seating and safety restraints chapter Air bag readiness Iluminates to confirm that the air o bags front or side are operational If the light fails to illuminate I continues to flash or remains on have the system serviced immediately 12 Instrument Cluster Charging system Illuminates when the battery is not charging properly Low fuel Illuminates when the fuel level in the fuel tank is at or near empty refer to Fuel gauge in this chapter for more information Speed control Illuminates when the speed control is activated CA i Transmission control indicator light TCIL Illuminates when the overdrive function of the transmission has been turned OFF using the Transmission Control Switch TCS Refer to the Driving chapter for transmission function and operation
181. nition to the LOCK position then remove the key 2 Reinsert the key and turn the ignition to the OFF position 3 Press and hold down the brake pedal and shift into N Neutral 4 Start the vehicle If it is necessary to use the above procedure to move the gearshift lever it is possible that a fuse has blown or the vehicle s brakelamps are not operating properly Refer to Fuses and relays in the Roadside emergencies chapter Do not drive your vehicle until you verify that the brakelamps are working If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle for more than a few minutes The transmission and tires may be damaged or the engine may overheat Always set the parking brake fully and make sure the gearshift is latched in P Park Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your dealer or a qualified service technician Driving with a 4 speed automatic transmission Understanding gearshift positions To put your vehicle in gear start the engine depress the brake pedal then move gearshift lever out of P Park Hold the brake pedal down while you move the gearshift lever from
182. not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Unlocking the doors f Press this control to unlock the driver door The interior lamps and running board lamps if equipped will illuminate Press the control a second time within three seconds to unlock all doors and liftgate Locking the doors amp Press this control to lock all doors liftgate or the driver s door If all doors are closed the parking lamps will flash once Press this control a second time within three seconds The door s will lock again the horn will chirp once and the parking lamps will flash once more If any of the doors are ajar the horn will make two quick chirps reminding you to properly close all doors 110 Locks and Security Power door unlock disable feature if equipped This feature will help protect your vehicle from unauthorized entry f a a NN The UNLOCK function on the power Ss door switch will not operate with ee the ignition OFF and twenty seconds after the doors are closed and electronically locked by the remote entry transmitter key pad or power door switch if pressed while the door was open The UNLOCK function will operate again after you unlock the vehicle using the remote entry transmitter or key pad turn the ignition to ON or open the door from inside of the vehicle Power door unlock disable feature activation deac
183. nouncements while in CD mode These announcements are broadcast by traffic capable RDS stations When in this mode traffic announcements will interrupt radio and CD play e Press the MENU control until TRAFFIC is displayed e Press the SEL control to engage the feature The display will read TRAFFIC ON This feature also allows you to control the volume of traffic announcements With the display reading TRAFFIC ON adjust the volume using the volume control to the desired level The volume level will show at the bottom of the display Interrupting traffic announcements will be at the selected volume level To disengage the feature press the MENU control until TRAFFIC ON displays Press the SEL control The display will read TRAFFIC OFF Traffic announcements are not available in most U S markets 39 Entertainment Systems Program type This feature allows you to search for RDS stations selectively by their program type Press the MENU control until FIND program type is displayed A Use the SEL control to select the sll program type With the feature on Y use the SEEK or SCAN control to find the desired program type from the following selections e Classic e Country e Info e Jazz e Oldies e R amp B e Religious e Rock e Soft e Top 40 Show This feature allows you to select the R type of RDS broadcast information the radio will regularly show in the mew SEL display Vv With RDS activated pres
184. nstructions of the equipment manufacturers Please read the section Air bag in the Seating and safety restraints chapter Failure to follow the specific warnings and instructions could result in personal injury Front seat mounted rear facing child or baby seats should NEVER be used in front of a passenger side air bag Notice to owners of diesel powered vehicles Read the 7 3 Liter Power Stroke Direct Injection Turbo Diesel Owner s Guide Supplement for information regarding correct operation and maintenance of your diesel powered light truck Introduction Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles Before you drive your vehicle please read this Owner s Guide carefully Your vehicle is not a passenger car As with other vehicles of this type failure to operate this vehicle correctly may result in loss of control or an accident Snowplowing The Excursion is not recommended for snowplow installation Ford makes no representation as to the suitability of the Excursion for snowplowing in particular regarding the potential for exceeding vehicle weight limits airbag SRS deployment sensitivity vehicle crash integrity or powertrain durability The Snowplow Package Option is not available Middle East North Africa vehicle specific information For your particular global region your vehicle may be equipped with features and
185. o data system feature e SELECT HOURS Refer to Setting the clock e SELECT MINUTES Refer to Setting the clock When in CD mode you can access SELECT HOURS SELECT MINUTES or COMP ON OFF SELECT HOURS SELECT MINUTES Allows you to adjust the hours and minutes Refer to Setting the clock 37 Entertainment Systems TRAFFIC ON OFF Traffic announcements can be programmed as local or distant Refer to Traffic announcements RDS ON OFF This feature allows your audio system to receive text information from RDS equipped FM radio stations Refer to Radio Data System feature FIND type Allows you to select your desired FM program type and search for that selection SHOW Allows you to select from NAME displays the name of the radio station TYPE displays the RDS program type rock jazz etc or NONE deactivates the RDS display Traffic announcements This feature allows you to hear traffic announcements When in this mode traffic announcements will h interrupt radio and CD play v When in FM mode and RDS is activated press the MENU until TRAFFIC OFF displays Press the SEL control to engage the feature The display will read TRAFFIC ON This feature also allows you to control the volume of traffic announcements With the display reading TRAFFIC ON adjust the volume using the volume control to the desired level The volume level will show at the bottom of the display Interrupting traffic ann
186. oading and before closing the cargo doors e To close and lock the liftgate and cargo doors close the left cargo door first then the right cargo door then pull down and close the liftgate Lock the TriDoor with the key key fob or the power door lock button 105 Driver Controls The cargo doors and liftgate should be closed before driving your vehicle Leaving the liftgate and or the cargo doors open could cause serious damage to the TriDoors and its components as well as allowing carbon monoxide to enter the vehicle If you must drive with the cargo doors and liftgate window open keep the vents open so outside air comes into the vehicle LUGGAGE RACK Maximum load is 90 kg 200 Ibs on the roof rack structure or 45 kg 100 Ibs on the roof panel slats evenly distributed If it is not possible to distribute the load position it as far rearward as possible Use adjustable tie down loops to secure the load To adjust the cross bar position 1 Release the latch at both ends of the cross bar both cross bars are adjustable 2 Slide cross bar to the desired location 3 Tighten the latch at both ends of the cross bar To remove the cross bar assembly from the roof rack side rails 1 Loosen the latch at both ends of the cross bar both cross bars are adjustable 2 Slide cross bar to the end of the rail 3 Press down on the locking feature inside the side rail and slide the cross bar over it 4 Slide the ass
187. ond to the factory set code Unlocking the doors with the keyless entry system To unlock the driver s door enter either the factory set code or personal code each digit pressed within five seconds of the prior digit The interior lamps will illuminate To unlock all doors enter the factory set code or personal code 1 2 F driver door unlocks and press the 3 4 control within five seconds Locking the doors with the keyless entry system It is not necessary to first enter the factory or personal code prior to locking all doors To lock all the doors e Press the 7 8 and the 9 0 control at the same time Autolock This feature automatically locks all vehicle doors when the following conditions are met e all doors are closed and e the brake is pressed before reaching 8 km h 5 mph and e the ignition is in the RUN position and the vehicle is traveling more than 8 km h 5 mph Relock The autolock feature repeats when the following conditions are met e any door is opened then closed while the ignition is in the RUN position and e the brake is pressed before reaching 8 km h 5 mph and 115 Locks and Security e the vehicle is travleing more than 8 km h 5 mph Deactivating activating autolock There are 3 methods to enable disable this feature One through your dealer the second with a power door unlock lock sequence and the third with the keypad B
188. ontrols will always override those of the rear seat controls Press the memory preset controls 2 ma and 4 simultaneously to toggle ED 3 E C ED o between single play and the Personal Audio Feature Liquid Crystal Display LCD flip down screen The screen rotates down to view and up into housing to store when not in use Be sure the screen is latched into the housing when being stored 51 Entertainment Systems foo ie root i 1 7 0 diagonal active matrix liquid crystal display LCD screen 2 Screen housing 3 Dimmer switch Toggle to increase decrease the brightness of the screen Playback and format e The DVD player of your Family Entertainment System FSES can only be used in the playback mode The DVD player does not offer a record feature e The system plays standard CDs or DVDs e The DVD player is only capable of playback of DVDs and CDs The player is not compatible with CDR RW media Family Entertainment System FES protection circuits High temperature sensor circuit e Excessively high temperatures may cause damage to the DVD player e When the temperature of the DVD player becomes too hot the high temperature sensor circuit stops machine operation DVD CD will illuminate in the radio display General operating tips e When the engine is not running use the system sparingly otherwise it will run the battery down e When
189. oolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months If you drive in extremely hot climates e It is still necessary to maintain the coolant concentration above 40 e NEVER decrease the coolant concentration below 40 237 Maintenance and Specifications e Decreased engine coolant concentrations below 40 will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage e Decreased engine coolant concentrations below 40 will decrease the freeze protection characteristics of the engine coolant and may cause engine damage e Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive Vehicles driven year round in non extreme climates should use a 50 50 mixture of engine coolant and distilled water for optimum cooling system and engine protection What you should know about fail safe cooling if equipped If the engine coolant supply is depleted this feature allows the vehicle to be driven temporarily before incremental component damage is incurred The fail safe distance depends on ambient temperatures vehicle load and terrain How fail safe cooling works If the engine begins to overheat e The engine coolant temperature gauge will move to the red hot area I e The 7 and E sym
190. options that are different from the ones that are described in this Owner Guide therefore a supplement has been supplied that complements this book By referring to the pages in the provided supplement you can properly identify those features recommendations and specifications that are unique to your vehicle Refer to this Owner Guide for all other required information and warnings Introduction These are some of the symbols you may see on your vehicle Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag Side Child Seat Installation Warning Brake System Brake Fluid Non Petroleum Based AdvanceTrac Hazard Warning Flasher Fuse Compartment Windshield Wash Wipe Rear Window Defrost Demist NP EOL E gt oN en t See Owner s Guide Air Bag Front Child Seat Child Seat Tether Anchorage Anti Lock Brake System Traction Control Master Lighting Switch Fog Lamps Front Fuel Pump Reset Windshield Defrost Demist Power Windows Front Rear ey Ww fi xX 0 YS YY A A Introduction Vehicle Symbol Glossary Power Window Lockout Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack Low tire warning m iep Da 85 p gt Li Sg Child Safety Door Lock Unlock a Panic Alarm Engine Coolant Do Not Op
191. or ON position DO NOT START THE ENGINE 2 Wait until the safety belt warning light turns off Approximately 1 2 minutes e Steps 3 5 must be completed within 60 seconds or the procedure will have to be repeated 3 Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled This can be done before or during BeltMinder warning activation 4 Turn on the parklamps headlamps turn off the parklamps headlamps 5 Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled 141 Seating and Safety Restraints e After step 5 the safety belt warning light will be turned on for three seconds 6 Within seven seconds of the safety belt warning light turning off buckle then unbuckle the safety belt e This will disable BeltMinder if it is currently enabled or enable BeltMinder if it is currently disabled 7 Confirmation of disabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds 8 Confirmation of enabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds followed by three seconds with the safety belt warning light off then followed by flashing the safety belt warning light four times per second for three seconds again 9 After receiving confirmation the deactivation activation procedure is complete Safety belt extension assembly If the safety belt
192. or unlock the vehicle doors without using the key Your vehicle has a factory set 5 digit code that operates the keyless entry system You can also program your own 5 digit personal entry code The factory set code is located e on the owner s wallet card in the glove compartment When pressing the controls on the keyless entry keypad press the middle of the controls to ensure a good activation Programming your own personal entry code To program your own code 1 Enter factory set code keypad will illuminate for five seconds when a key is pressed 2 Press 1 2 control within five seconds of step 1 3 4 5 6 7 8 9 0 3 Enter your personal 5 digit code Enter each digit within five seconds of previous one Do not set a code that includes five of the same number or presents them in sequential order Thieves can easily figure out these types of codes Your personal code does not replace the permanent code that the dealership gave you You can use either code to unlock your vehicle If a second personal code is entered the module will erase it in favor of the new code 114 Locks and Security If you wish to erase your personal code use the following instructions 1 Enter factory set code 2 Press 1 2 control within five seconds of step 1 and release 3 Within five seconds of step 2 press and hold the 1 2 control for two seconds The system will now only resp
193. ore pursuing replacement or repurchase remedies provided by certain state laws This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson Moss Warranty Act or state replacement or repurchase laws FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan Ford ESP coverage Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company in the U S and Ford of Canada in Canada It provides the following e Benefits during the warranty period depending on the plan you purchase such as reimbursement for rentals coverage for certain maintenance and wear items e Protection against covered repair costs after your Bumper to Bumper Warranty expires You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer There are several plans available in various time distance and deductible combinations which can be tailored to fit your own driving needs Ford ESP also offers reimbursement benefits for towing and rental coverage When you buy Ford ESP you receive Peace of Mind protection throughout the United States and Canada provided by a network of more than 5 000 participating Ford or Lincoln Mercury and Ford of Canada dealers If you did not take advantage of the Ford Extended Service Plan at the
194. orn or do not function properly INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth then dry with a dry cloth e Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel The dull finish in this area helps protect the driver from undesirable windshield reflection e Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system e Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the painted surfaces WOOD TONE TRIM e Clean the area with a damp cloth then dry by wiping with a dry soft clean cloth e Do not use household or glass cleaners as these may damage the finish 221 Cleaning INTERIOR For fabric carpets cloth seats and safety belts e Remove dust and loose dirt with a vacuum cleaner e Remove light stains and soil with Extra Strength Upholstery Cleaner E8AZ 19523 AA If grease or tar is present on the material spot clean the area first with Spot and Stain Remover F3AZ 19521 WA Never saturate the seat covers with cleaning solution e Do not use household cleaning products or glass cleaners which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials LEATHER SEATS IF EQUIPPED Your
195. ot need to be replaced Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision Refer to Cleaning and maintaining the safety belts in the Cleaning chapter AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM SRS aam Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles 143 Seating and Safety Restraints Important supplemental restraint system SRS precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module All occupants of the vehicle i
196. ouncements will be at the selected volume level To disengage the feature press the MENU control until TRAFFIC ON displays Press the SEL control The display will read TRAFFIC OFF RDS traffic seek feature When in traffic mode you can use the SEEK feature to seek up or down the listenable traffic capable frequencies With the RDS activated press MENU until TRAFFIC ON is displayed Press and hold the SEEK control until the desired selection is reached The feature disengages when the control is released RDS traffic scan feature When in traffic mode you can use the SCAN feature to scan up the frequency band for listenable traffic capable frequencies 38 Entertainment Systems With the RDS activated press the MENU control until TRAFFIC ON is displayed Press the SCAN control SCAN TRAFFIC will display The audio system will scan to all traffic capable frequencies If no valid stations are found after one pass the scan function is cancelled and NOT FOUND displays Radio data system RDS feature This feature allows your audio system to receive text information from RDS equipped FM radio stations v To activate RDS e When in FM mode press the MENU control until RDS OFF displays e Press the SEL control to engage this feature RDS ON RDS features Once the RDS feature is on press the MENU control to scroll through the following selections Traffic announcements This feature allows you to hear traffic an
197. owever a slingbelt with T hooks and a wheel dolly can also be used if all four wheels are off the ground 207 Roadside Emergencies An alternative for towing a 4x4 vehicle is to e put the transfer case in neutral On manual 4WD systems put the AWD shift lever in N Neutral on electronic shift on the fly 4WD systems press the 2WD portion of the 4WD control unlock the front hub locks refer to Four wheel drive 4WD Operation if equipped in the Driving chapter e lift the rear wheels of the vehicle using a wheel lift or a sling belt with T hooks If the vehicle is towed by other means or incorrectly vehicle damage may occur Ford Motor Company provides a towing manual for all authorized tow truck operators Have your tow truck operator refer to this manual for proper hook up and towing procedures for your vehicle 208 Customer Assistance GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle It is preferred that you return to the Ford dealer where your vehicle was purchased when warranty repairs are needed However you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs Certain warranty repairs require special training though so not all dealers are authorized to perform all warranty repairs That means that depending on the warranty repair needed the vehicle may need to be
198. panel lights see your dealer Interior bulbs Check the operation of the following interior bulbs frequently e dome lamps e map lamps e second row reading lamps e third row reading lamp For bulb replacement see a qualified service technician or your dealer Replacing headlamp bulbs 1 Make sure that the headlamp control is in the OFF position 2 Open the hood 3 Disconnect the electrical connector from the bulb by pulling rearward 4 Remove bulb retainer ring by turning it counterclockwise about 1 4 turn then slide the ring off the plastic base 5 Without turning carefully pull bulb out of headlamp assembly Handle a halogen headlamp bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass The oil from your hand could cause the bulb to break the next time the headlamps are operated 6 Insert the glass end of the new bulb into the headlamp assembly When the grooves in the plastic base are aligned push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly 77 Lights 7 Install bulb retaining ring over the plastic base and lock the ring into the socket by turning it clockwise until you feel a stop 8 Connect the electrical connector into the rear of the plastic base until it snaps Replacing front parking turn signal bulbs 1 Make sure headlamp switch is in OFF position 2
199. pened Volume power control Press the control to turn the audio VOL PUSH ON system on or off Audio power can also be turned on by pressing the AM FM select control or the TAPE CD select control Turn control to raise or lower K N volume VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on 19 Entertainment Systems Bass adjust The bass adjust control allows you a to increase or decrease the audio lt BASS system s bass output Press the BASS control then press lt q to decrease the bass output and gt to increase the bass output Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output Press the TREB control then press to decrease the treble output and gt to increase the treble output Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Press the BAL control then press lt to shift sound to the left and e to shift sound to the right 20 Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Press the FADE control then press gt to shift the sound to the front and Ei to shift the sound to the rear A 4 Seek
200. perature falls below 3 C 88 F the display will alternate from ICE to the outside RESET temperature at a two second rate for one minute C Off In this mode the display is off Compass The compass display is contained in the overhead console The vehicle heading is displayed as one of N NE E SE S SW W and NW The compass heading is displayed in average fuel economy modes fuel range modes and temperature modes 97 Driver Controls The compass reading may be affected when you drive near large buildings bridges power lines and powerful broadcast antenna Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy Adjustments may need to be made to the zone and calibration of the compass Compass zone adjustment 1 Determine which magnetic zone you are in for your geographic location by referring to the zone map 2 Locate the trip computer on the overhead console 3 Turn ignition to the ON position 4 Press and hold both trip computer controls After approximately four seconds the trip computer will enter zone setting mode Zone setting mode is indicated when the display lights the ZONE indicator 5 Release both controls Subsequent pressing of either control will increment the zone Press the control repeatedly until the correct zone setting for your geographic location is displayed on the trip computer
201. pg is lost for every 180 kg 400 lb of weight carried e Adding certain accessories to your vehicle for example bug deflectors rollbars light bars running boards ski luggage racks may reduce fuel economy Using fuel blended with alcohol may lower fuel economy e Fuel economy may decrease with lower temperatures during the first 12 16 km 8 10 miles of driving Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain e Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal e Four wheel drive operation Gf equipped is less fuel efficient than two wheel drive operation e Close windows for high speed driving EPA window sticker Every new vehicle should have the EPA window sticker Contact your dealer if the window sticker is not supplied with your vehicle The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles 246 Maintenance and Specifications It is important to note the box in the lower left corner of the window sticker These numbers represent the Range of L 100 km MPG expected on the vehicle under optimum conditions Your fuel economy may vary depending upon the method of operation and conditions EMISSION CONTROL SYSTEM tC Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with
202. porting any shift concerns to your dealer Driving off road with truck and utility vehicles AWD vehicles are specially equipped for driving on sand snow mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles both on and off the road How your vehicle differs from other vehicles Truck and utility vehicles can differ from some other vehicles Your vehicle may be higher to allow it to travel over rough terrain without getting hung up or damaging underbody components 173 Driving The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car Maintain steering wheel control at all times especially in rough terrain Since sudden changes in terrain can result in abrupt steering wheel motion make sure you grip the steering wheel from the outside Do not grip the spokes Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps You should either know the terrain or examine maps of the area before driving Map out your route before driving in the area To maintain steering and braking control of your vehicle you must have all four wheels on the ground and they must be rolling not sliding or spinning Basic operating principles e Do not use 4WD on dry hard surfaced roads Doing so will produce excessive noise increase tire wear and may damage drive components 4WD modes are only intende
203. r hills A danger lies in losing traction slipping sideways and possibly rolling over Whenever driving on a hill determine beforehand the route you will use Do not drive over the crest of a hill without seeing what conditions are on the other side Do not drive in reverse over a hill without the aid of an observer When climbing a steep slope or hill start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started This reduces strain on the engine and the possibility of stalling If you do stall out do not try to turn around because you might roll over It is better to back down to a safe location Apply just enough power to the wheels to climb the hill Too much power will cause the tires to slip spin or lose traction resulting in loss of vehicle control Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating Do not descend in neutral disengage overdrive or manually shift to a lower gear When descending a steep hill avoid sudden hard braking as you could lose control When you brake hard the front wheels can t turn and if they aren t turning you won t be able to steer The front wheels have to be turning in order to steer the vehicle Rapid pumping of the brake pedal will help you slow the vehicle and still maintain steering control If your vehicle has anti lock brakes apply the brakes steadi
204. r intermittent squeal or groan noises when the brakes are applied Such noises are usually heard during the first few brake applications in the morning however they may be heard at any time while braking and can be aggravated by environmental conditions such as cold heat moisture road dust salt or mud If a metal to metal continuous grinding or continuous squeal sound is present while braking the brake linings may be worn out and should be inspected by a qualified service technician If you are driving down a long or steep hill shift to a lower gear Do not apply your brakes continuously as they may overheat and become less effective 160 Driving Anti lock brake system ABS This vehicle is equipped with an anti lock braking system ABS A noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel bumps wet or snowy roads is normal and indicates proper functioning of the vehicle s anti lock brake system If the vehicle has continuous vibration or shudder in the steering wheel while braking the vehicle should be inspected by a qualified service technician The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency The wheels are prevented from locking even when the brakes are firmly applied The accompanying il
205. raction Lok axles Service refill capacities are determined by filling the rear axle to the bottom of the filler hole with the specified lubricant 3Add the coolant type originally equipped in your vehicle If equipped with auxiliary rear heater add an additional 1 4 L 1 5 quarts Ensure the correct automatic transmission fluid is used Transmission fluid requirements are indicated on the dipstick or on the dipstick handle Check the container to verify the fluid being added is of the correct type Refer to your scheduled maintenance guide to determine the correct service interval Some transmission fluids may be labeled as dual usage such as MERCON and MERCON V These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON type fluid However these dual usage fluids may be used in transmissions that require the MERCON V type fluid MERCON and MERCONE V type fluids are not interchangeable DO NOT mix MERCON and MERCONE V Use of a transmission fluid that indicates dual usage MERCON and MERCON V in an automatic transmission application requiring MERCON may cause transmission damage Use of any fluid other than the recommended fluid may cause transmission damage Indicates only approximate dry fill capacity Some applications may vary based on cooler size and if equipped with an in tank cooler The amount of transmission fluid and fluid level should be set by the indic
206. re the last strong station available To deactivate autoset and return to your audio system s manually set memory stations press the AM FM control again Seiting the clock Press the MENU control until SELECT HOUR or SELECT MINUTE is displayed The menu mode must be engaged to enable clock mode 32 Entertainment Systems Use the SEL control to manually set the time A e Press A to increase SEL hours minutes y e Press vy to decrease hours minutes Press the MENU control again to disengage the clock mode Tune disc adjust The tune control works in radio or CD mode Tune adjust in radio mode e Press E to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Disc adjust for CD mode e Press lt q to select the previous disc Play will begin on the first track of the disc unless shuffle mode is engaged Refer to Shuffle feature for more information Hold the control to continue reversing through the discs e Press gt to select the next disc Hold the control to fast forward through the remaining discs 33 Entertainment Systems CD select CD mode may be entered by pressing the CD control and the LOAD control Load the CD into the audio system
207. ree repeat the previous procedure but press controls 1 and 2 simultaneously A position can only be recalled when the transmission gearshift is in Park A memory seat position may be programmed at any time Seating and Safety Restraints The memory seat positions are also recalled when you press your remote entry transmitter UNLOCK control To program the memory seat to remote entry transmitter refer to Remote entry system in the Controls and features chapter Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to move A the lumbar support forward for more direct support I Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support gt Adjusting the front power seat if equipped f Never adjust the driver s seat or seatback when the vehicle is moving A Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop A Always drive and ride with your seatback upright and the lap belt snug and low across the hips A Reclining the seatback can cause an occupant to slide under the seat s safety belt resulting in severe personal injuries in the event of a collision The control is located on the outboard side of the seat cushion 122 Seating and Safety Restraints Press to raise or lower the front s portion of the seat cushion N N Press to raise or lower the rear
208. removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle e MAX A C Uses recirculated air to cool the vehicle MAX A C is noisier than A C but more economical and will cool the inside of the vehicle faster Airflow will be from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle e A C Uses outside air to cool the vehicle It is quieter than MAX A C but not as economical Airflow will be from the instrument panel registers 59 Climate Controls 7s Panel Distributes outside air through the instrument panel registers However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode OFF Outside air is shut out and the fan will not operate For short periods of time only use this mode to prevent undesirable odors from entering the vehicle J Panel and floor Distributes outside air through the instrument panel registers and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel regist
209. ressure begins to release 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to turn it counterclockwise and remove the cap 5 Fill the coolant reservoir slowly with the proper coolant mixture see above to within the cold fill range or the cold full level on the reservoir If you removed the radiator cap in an overflow system fill the radiator until the coolant is visible and radiator is almost full 6 Replace the cap Turn until tightly installed Cap must be tightly installed to prevent coolant loss After any coolant has been added check the coolant concentration see Checking Engine Coolant section If the concentration is not 50 50 protection to 34 F 36 C drain some coolant and adjust the concentration It may take several drains and additions to obtain a 50 50 coolant concentration Whenever coolant has been added the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle If necessary add enough 50 50 concentration of engine coolant and distilled water to bring the liquid level to the proper level If you have to add more than 1 0 liter 1 0 quart of engine coolant per month have your dealer check the engine cooling system Your cooling system may have a leak Operating an engine with a low level of coolant can result in engine overheating and possible engine damage 236 Maintenance
210. rest Ford Motor Company dealership or your selling dealer if within 56 3 km 35 miles of the nearest Ford Motor Company dealership one tow per disablement Even non warranty related tows like accidents or getting stuck in the mud or snow are covered some exclusions apply such as impound towing or repossession Canadian customers refer to your Owner Information Guide for information on e Coverage period e Exact fuel amounts e Towing of your disabled vehicle e Emergency travel expense reimbursement e Travel planning benefits USING ROADSIDE ASSISTANCE Complete the roadside assistance identification card and place it in your wallet for quick reference In the United States this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln In Canada the card is found in the Owner Information Guide in the glove compartment U S Ford or Mercury vehicle customers who require roadside assistance call 1 800 241 3673 Lincoln vehicle customers call 1 800 521 4140 189 Roadside Emergencies Canadian customers who require roadside assistance call 1 800 665 2006 If you need to arrange roadside assistance for yourself Ford Motor Company will reimburse a reasonable amount To obtain reimbursement information U S Ford or Mercury vehicles customers call 1 800 241 3673 Lincoln vehicle customers call 1 800 521 4140 Canadian customers who need to obt
211. restraints chapter 2 Make sure the headlamps and vehicle accessories are off 3 Make sure the parking brake is set 4 Make sure the gearshift is in P Park 157 Driving 5 Turn the key to 4 ON without p turning the key to 5 START Z 4 If there is difficulty in turning the 3 key firmly rotate the steering wheel N 5 left and right until the key turns freely This condition may occur 2 when e front wheels are turned Gy e front wheel is against the curb e steering wheel is turned when getting in or out of the vehicle ae wugngrnguny 4 gt ayut ROY Om Me es 40 59 60 3 b H S 30 a w 70 amp D Ss E 42 H RPMX1000 z E mm mn PI oa Me 2 80 S 52 o3 160 A F E olos CBs km h RESET D Make sure the corresponding lights illuminate or illuminate briefly If a light fails to illuminate have the vehicle serviced e If the driver s safety belt is fastened the A light may not illuminate Starting the engine Note Whenever you start your vehicle release the key as soon as the engine starts Excessive cranking could damage the starter 1 Turn the key to 5 START without pressing the accelerator pedal and release as soon as the engine starts The key will return to 4 ON 2 If the temperature is above 12 C 10 F and the engine does not start within five seconds on the first try turn the key to OFF wait 10 s
212. s recommended for your vehicle contact a district or owner relations customer relationship office The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage Ford Motor Company Ford of Canada is not responsible for any damage caused by use of improper fuel In the United States using leaded fuel may also result in difficulty importing your vehicle back into the U S If your vehicle must be serviced while you are traveling or living in Central or South America the Caribbean or the Middle East contact the nearest Ford dealership If the dealership cannot help you write or call FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park 3 Allen Park Michigan 48101 U S A Telephone 813 594 4857 FAX 813 390 0804 215 Customer Assistance If you are in another foreign country contact the nearest Ford dealership If the dealership employees cannot help you they can direct you to the nearest Ford affiliate office If you buy your vehicle in North America and then relocate outside of the U S or Canada register your vehicle identification number VIN and new address with Ford Motor Company Worldwide Direct Market Operations ORDERING ADDITIONAL OWNER S LITERATURE To order the publications in this portfolio contact Helm Incorporated at HELM INCORPORAT
213. s the i MENU control until SHOW is displayed mew SEL Use the SEL control to select TYPE v displays the RDS program type rock jazz etc NAME displays the name of the radio station or NONE deactivates the RDS display 40 Entertainment Systems Mute mode Press the control to mute the playing media Press the control again to return to the playing media REAR SEAT CONTROLS IF EQUIPPED The Rear Seat Controls RSC allow VOLUME MEDIA MEM lt lt SEEK gt the rear seat passengers to operate COO QO ees the radio tape CD or CD changer if equipped CO O a a To turn on the rear seat controls press the memory preset controls 3 and 5 at the same time The A will appear in the radio display Pressing 3 and 5 at the same time again will turn the rear seat controls off If there is a discrepancy between the rear seat and the front audio controls i e both trying to listen to the same playing media the front audio system will receive the desired selection ADJUSTING THE VOLUME Press the control to increase _ volume VOLUME MEDIA MEM lt lt SEEK Press the control to decrease COO volume ot From the RSC controls the speaker CO ov o volume can not be set higher than the current volume radio setting Once in headphone mode the RSC volume controls will only change volume in the headphones to a desired level and will have no effect on the front speakers
214. s to select the function pointed to within the active menu May also be used by some user interactive discs during movie play 5 MENU control Press to bring up the disc menu 6 AUX control Press to switch DVD player from play mode to auxiliary mode 7 Auxiliary jacks Insert lines for standard video game players 8 STOP EJECT control Press once to stop DVD play Press again to eject the DVD 9 DISPLAY DISP control Press to enable on screen display of player menu and user display adjustments DVD control features Menu control Press the MENU control to enter into MENU mode This allows you to move and choose within the DVD generated menu structure Once in MENU mode e Press the NEXT control to move the cursor one position upward 44 Entertainment Systems e Press the PREV control to move the cursor one position downward e Press the REV control to move the cursor left one position e Press the FWD control to move the cursor right one position Next Previous control The NEXT up and PREV down controls allow you to access the next or previous track on a CD or chapter on a DVD When pressed the playing audio will mute momentarily while the next chapter is accessed Press and hold to advance or reverse multiple tracks or chapters REV FWD control The REV reverse and FWD forward controls allow you to adjust the playback Press the REV FWD control during playback mode to reverse or adv
215. sages together for a more consistent listening level Press the COMP control to activate and deactivate compression adjust Shuffle feature The shuffle feature operates in CD mode and plays all tracks in random ____ __ gt order Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again Mute mode Press the MUTE control to mute the playing media Press the MUTE control again to return to the playing media 27 Entertainment Systems PREMIUM AM FM STEREO IN DASH SIX CD RADIO HOA CE C Enee O O PUSH ON e CC Ca Ca C Ce te Your vehicle is equipped with a delayed accessory feature This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off or until a door is opened Volume power control Press the control to turn the audio system on or off n PUSH ON Turn the control to raise or lower x volume PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on 28 Entertainment Systems Speed sensitive volume With this feature radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise The recommended level for speed sensitive volu
216. sing the blue cooler or red warmer controls Temperature conversion EXT TEMP i Press AUTO and at the same time for one second to switch between Fahrenheit and Celsius Fan speed C5 EXT TEMP Nea EDEDED E When AUTO is pressed fan speed is adjusted automatically for existing conditions You can override fan speed at any time To control fan speed manually press the fan control to cancel the automatic fan speed operation Press the control up for higher fan speed or down for lower 64 Climate Controls fan speed The display will show 4e and a a bar graph to indicate manual fan speed operation and relative speed To return to automatic fan operation press AUTO A C control Used to manually enable or disable A the operation of the air conditioning in all modes except C47 In all s modes the air conditioning will only S F a function if the outside temperature w Z v is about 6 C 43 F or higher When manual A C is selected A C will be displayed in the display window In GV if the outside temperature is about 6 C 48 F or higher the air conditioner will automatically dehumidify the air to reduce window fogging However A C will not be displayed in the display window The air conditioning compressor can operate in all modes except OFF However the air conditioning will only fun
217. sion Board members review all available information related to each complaint including oral presentations and arrive at a fair and impartial decision Board review may be terminated at any time by either party Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board Since the Board generally meets once a month it may take longer for the Board to consider some cases After a case is reviewed the Board mails you a decision letter and a form on which to accept or reject the Board s decision The decisions of the Board are binding on Ford and in some cases on the dealer but not on consumers who are free to pursue other remedies available to them under state or federal law To request a DSB Brochure Application For a brochure application speak to your dealer or write call to the Board at the following address phone number Dispute Settlement Board P O Box 5120 Southfield MI 48086 5120 1 800 428 3718 You may also contact the North American Customer Relationship Center at 1 800 392 3673 Ford TDD for the hearing impaired 1 800 232 5952 or by writing to the Center at the following address Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 UTILIZING THE MEDIATION ARBITRATION PROGRAM CANADA ONLY In those cases where you continue to feel that the efforts by Ford and the dealer to resolv
218. sion damage Use of any fluid other than the recommended fluid may cause transmission damage ENGINE DATA Engine 87 octane eer 1 3 1 4 mm 1 3 1 4 mm park plug gap 0 052 0 056 inch _ 0 052 0 056 inch Ignition system Coil on plug Coil on plug Refer to the 7 3 Liter Power Stroke Direct Injection Turbo Diesel Owner s Guide Supplement for diesel engine information 265 Maintenance and Specifications VEHICLE DIMENSIONS EXCURSION Dimension 4x2 mm in 4x4 mm in k 1 Overall length 2 Overall width 3 Overall height 4 Wheelbase 5 Track Front Rear 738 68 D 738 68 DI 1 729 68 1 1 729 68 1 266 Maintenance and Specifications C DIC ICO 3 l JK C JK J z le iT ters IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located The Certification label is located on the front door latch pillar on the driver s side MFD BY FORD MOTOR CO IN U S A DATE XXXXX GVWR XXXXX_ LB XXXXX KG FGAWR XXXXXX XXXXXXX _RGAWR XXXXXXX XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN
219. smission fluid may cause shift and or engagement concerns and or possible damage Do not use supplemental transmission fluid additives treatments or cleaning agents The use of these materials may affect transmission operation and result in damage to internal transmission components Checking and adding transfer case fluid if equipped 1 Clean the filler plug z 2 Remove the filler plug and inspect the fluid level 3 Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening Use only fluid that meets Ford specifications Refer to Lubricant Specifications in this chapter 253 Maintenance and Specifications AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element When changing the air filter element use only the Motorcraft air filter element listed Refer to Motorcraft Part Numbers Note Do not start your engine with the air cleaner removed and do not remove it while the engine is running Changing the air filter element gasoline engines only 1 Loosen the clamp that secures the air filter element in place 254 Maintenance and Specifications 2 Carefully separate the two halves of the air filter housing 3 Remove the air filter element from the open end of the air filter housing 4 Install a new air filter element ens
220. ssccsesseceeeessees 256 TOWING aran nO ARE 184 recreational towing s 188 trailer tOWIN ou 184 WIOECKED s cdssosdesesancectedaesncchiditects 207 Traction lok rear axle 163 Transfer case fluid checking 253 TYANSMISSION siyir onsas 164 fluid checking and adding automatic oe eee eects 251 fluid refill capacities 260 lubricant specifications s s s 263 265 Transmission control indicator light eee 13 Trip Odometer eeeeceeeeeeeeees 18 Turn signal 13 74 vV Vehicle dimensions 66 266 Index Vehicle Identification Number VIN E 268 Vehicle loading ceeeee 181 Ventilating your vehicle 160 WwW Warning chimes 0 06 14 15 Warning lights see Lights 10 Washer fluid si ccscscssieeresaceccnenes 227 Water Driving through 181 278 Windows POWEF a scdececiehiibieanadne ied 87 rear wiper washef c0008 81 Windshield washer fluid and wipers checking and adding fluid 227 checking and cleaning 82 liftgate reservoir oo 228 Operation rrr 81 replacing wiper blades 82 Wrecker towing woo 207 279 280
221. sscedesaces 146 indicator light 12 147 OPELAGLON sessao 146 passenger air bag o 146 Air cleaner filter 00 254 260 Air conditioning 0 0 62 auxiliary heater and air CONITIONEY 0 0 ceeeeessecceeeseeeeees 69 manual heating and air conditioning system s 59 Antifreeze see Engine coolant 2338 Anti lock brake system see Brakes siseses 161 Anti theft system warning light ssissrsserseceereress 14 Audio system see Radio 19 28 Automatic transmission driving an automatic overdrive oe ceeeeccecesseeeseneeeees 165 fl id adding scciicssdsscdsseeveccadeesss 251 fluid checking 0 00 251 fluid refill capacities 260 fluid specification 0 265 Auxiliary power point 85 Axle lubricant specifications 263 265 refill capacities 0 0 0 260 WaACUION OK srreses isean 163 272 B Battery Jscsisssecsisaiestesisineeisteeesas 231 acid treating emergencies 231 charging system warning TENEI U AR A S E EEEE sneak eens 13 jumping a disabled battery 201 maintenance free ccceees 231 replacement specifications 260 SOLVICING menyan en ran 231 BeltMinder ssissrrisirisisinirssris 139 Brakes sesranred nro ran 160 ANUIKAIOCK sareren nane 161 anti lock brake system ABS warning light 0 0 0 12 161 brake warning light 0 12 fluid checking and adding 250 fluid refill capacities
222. ssing the accelerator before or during starting Only use the accelerator when you have difficulty starting the engine For more information on starting the vehicle refer to Starting the engine in this chapter Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Do not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes in this chapter for more instructions 156 Driving If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs faster to warm the engine If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than 10 minutes at high engine RPM Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and safety
223. st intervals and downward for slow intervals Push tap the end of the stalk briefly for a single swipe no wash Push and hold the end of the stalk to activate washer The wash cycle will continue for up to ten seconds or until released After release there will be three clearing wipes Speed dependent wipers When the windshield wiper control is set on the intermittent settings speed sensitive front wipers automatically adjust as the vehicle s speed changes Rear window wiper washer controls For rear wiper operation rotate the rear window wiper and washer control to the desired position Select INT 1 3 5 second interval rear wiper INT 2 10 5 second interval rear wiper OFF Rear wiper and washer off For rear wash cycle rotate and hold as desired the rear wiper washer control to either GJ position From either position the control will automatically return to the INT2 or OFF position 81 Driver Controls Windshield wiper blades Check the wiper blades for wear at least twice a year or when they seem less effective Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades Checking the wiper blades If the wiper blades do not wipe properly clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent Rinse thoroughly with clean water To avoid damaging th
224. steps described above contact the Ford Customer Relationship Center to find an authorized dealership to help you In the United States Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 1 800 521 4140 TDD for the hearing impaired 1 800 232 5952 www ford com In Canada Customer Relationship Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD www ford ca In order to help you service your Ford or Lincoln Mercury vehicle please have the following information available when contacting a Customer Relationship Center e Your telephone number home and business e The name of the dealer and the city where the dealership is located e The year and make of your vehicle e The date of vehicle purchase e The current odometer reading e The vehicle identification number VIN If you still have a complaint involving a warranty dispute you may wish to contact the Dispute Settlement Board U S 210 Customer Assistance In some states in the U S you must directly notify Ford in writing before pursuing remedies under your state s warranty laws Ford is also allowed a final repair attempt in some states In the United States a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson Moss Warranty Act or to the extent allowed by state law bef
225. t from front or behind it will automatically adjust to minimize glare Press the control located on the KL bottom of the mirror to turn the mirror on or off The mirror will automatically return to the normal state whenever the vehicle is placed in R reverse when the mirror is C O on to ensure a bright clear view when backing up Do not clean the housing or glass of any mirror with harsh abrasives fuel or other petroleum based cleaning products 88 Driver Controls Power side view mirrors if equipped The ignition can be in any position to adjust the power side view mirrors To adjust your mirrors 1 Select L to adjust the left mirror 4 gt R to adjust the right mirror or R to adjust the right mirror MIRRORS LI 2 Move the control in the direction you wish to tilt the mirror MIRRORS L R eS gt Vv 3 Return to the center position to lock mirrors in place 4 Adjust spotter mirrors if equipped manually Heated outside mirrors GY if equipped Both mirrors are heated automatically to remove ice mist and fog when the rear window defrost is activated Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place These actions could cause damage to the glass and mirrors 89 Driver Controls Signal mirrors if equipped When the turn signal is activated th
226. t is imperative that you consult the relevant section of this guide before Lli touching or attempting adjustment of any kind Protecting the environment We must all play our part in protecting the environment Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim Information in this respect is highlighted in this guide with the tree symbol BREAKING IN YOUR VEHICLE There are no particular guidelines for breaking in your vehicle During the first 1 600 km 1 000 miles of driving vary speeds frequently This is recommended to give the moving parts a chance to break in Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper to Bumper Coverage Safety Restraint Coverage Corrosion Coverage and 7 3L Power Stroke Diesel Engine Coverage In addition your vehicle is eligible for Emissions Defect and Emissions Performance Warranties For a detailed description of what is covered and what is not covered refer to the Warranty Guide that is provided to you along with your Owner s Guide Special instructions For your added safety your vehicle is fitted with sophisticated electronic controls By operating other electronic equipment e g mobile telephone without exterior aerial electromagnetic fields can occur which can cause malfunctions of the vehicle electronics Therefore you should observe the i
227. t use alcohol methanol brine or any engine coolants mixed with alcohol or methanol antifreeze coolant Alcohol and other liquids can cause engine damage from overheating or freezing Do not add extra inhibitors or additives to the coolant These can be harmful and compromise the corrosion protection of the engine coolant Do not mix with recycled coolant unless from a Ford approved recycling process see Use of Recycled engine coolant section 235 Maintenance and Specifications For vehicles with overflow coolant systems with a non pressurized cap on the coolant recovery system add coolant to the coolant recovery reservoir when the engine is cool Add the proper mixture of coolant and water to the cold full level For all other vehicles which have a coolant degas system with a pressurized cap or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system follow these steps to add engine coolant To reduce the risk of personal injury make sure the engine is cool before unscrewing the coolant pressure relief cap The cooling system is under pressure steam and hot liquid can come out forcefully when the cap is loosened slightly 1 Before you begin turn the engine off and let it cool 2 When the engine is cool wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir an opaque plastic bottle Slowly turn cap counterclockwise left until p
228. t with any non body ow gloss black colored trim such as grained door handles roof racks bumpers side moldings mirror housings or the windshield cowl area The paint sealant will gray or stain the parts over time PAINT CHIPS Your dealer has touch up paint and sprays to match your vehicle s color Take your color code printed on a sticker in the driver s door jam to your dealer to ensure you get the correct color 218 Cleaning Remove particles such as bird droppings tree sap insect deposits tar spots road salt and industrial fallout before repairing paint chips Always read the instructions before using the products ALUMINUM WHEELS AND COVERS Aluminum wheel rims or covers are coated with a clearcoat paint finish In order to maintain their shine Clean with Detail Wash ZC 3 A which is available from your dealer Never apply any cleaning chemical to hot or warm wheel rims or covers Some automatic car washes may cause damage to the finish on your wheel rims or covers Chemical strength cleaners or cleaning chemicals in combination with brush agitation to remove brake dust and dirt could wear away the clearcoat finish over time Do not use hydrofluoric acid based or high caustic based wheel cleaners steel wool fuels or strong household detergent To remove tar and grease use Extra Strength Tar and Road Oil Removal B7A 19520 AA available from your dealer ENGINE Engines are more eff
229. taaceeeenss 242 running out of fuel 243 safety information relating to automotive fuels 0 ce 239 Fuses ss2zcchesiesissaecndeesseatedeess 191 192 G Garage door opener 84 99 Gas cap see Fuel cap 11 241 Gas mileage see Fuel economy 0cce 243 GauBES arreirar oA EE RA 15 engine coolant temperature GAUGE croa aa A TEE R 5 engine oil pressure gauge 16 THE gauge sorsara 17 OGOMECER sieisdissssecssbsvdesdsaceteesvass 18 Speedometer cccecccceseceeees 17 CACHOMELED siseisssdenveisesssaxcetegeages 18 trip Odometer cecccseeeeees 18 GAWR Gross Axle Weight Rating ueint anioni 181 calculating sssrinin 183 GOTNIGION v222 sesesisedessbecsesacetiers 181 driving with a heavy load 181 LOCATION ersun 181 GVWR Gross Vehicle Weight Rating ss cisictvessccdesseerseiegasccsarteerse 1 Calculating cviccisiivessgeress 181 183 GOHNIGION ss2 sesenisvedesssccsosscceens 181 driving with a heavy load 181 LOCATION asccsssesccsassicesessssacesaaiseets 181 H Hazard flashers cccccceeeee 190 Head restraints ssrcsisioreniss 124 Headlamps isceccciiecscsasstacdsvveascess 72 aming erkeers 74 autolamp system ccccceceeeee 72 bulb specifications 0000000000 76 daytime running lights 73 flash tO PASS ecccceessseeeeseeees 73 Migh DEAM sioesscasdssnemeduanernceecs 13 73 replacing bulbs 0 00 77 turning
230. tainment Systems Rewind The rewind control works in CD modes Press and hold the REW control Vv until the desired selection is reached If the beginning of the disc is reached the CD will begin play at the first track Release the control to disengage rewind mode When in rewind mode your audio system will automatically lower the volume level of the playing media Fast forward The fast forward control works in CD modes Press and hold the FF control until WN the desired selection is reached If the end of the disc is reached the CD will return to the first track Release the control to disengage fast forward mode When in fast forward mode your audio system will automatically lower the volume level of the playing media Load The load feature allows you to load single CDs into the player internal to the radio a This six disc CD player is equipped with a CD door Compact discs should only be inserted into the player after the door has been opened by the player Do not attempt to force the door open Compact discs should only be loaded by pressing the LOAD control Press the LOAD control You can choose which slot will be loaded by pressing the desired preset number If you do not choose a slot the system will choose the next available one Wait until the CD door opens Load the CD into the player LOADING CD is displayed When the CD has been loaded the door will close and the CD will begin to pl
231. taken to avoid inhaling excess fumes 240 Maintenance and Specifications The flow of fuel through a fuel pump nozzle can produce static electricity which can cause a fire if fuel is pumped into an ungrounded fuel container Use the following guidelines to avoid static build up when filling an ungrounded fuel container e Place approved fuel container on the ground e DO NOT fill a fuel container while it is in the vehicle including the cargo area e Keep the fuel pump nozzle in contact with the fuel container while filling e DO NOT use a device that would hold the fuel pump handle in the fill position Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1 8 turn on off feature When fueling your vehicle 1 Turn the engine off a Carefully turn the filler cap counterclockwise 1 8 of a turn until it stops 3 Pull to remove the cap from the fuel filler pipe 4 To install the cap align the tabs on the cap with the notches on the filler pipe 5 Turn the filler cap clockwise 1 8 of a turn until it stops If the Service Engine Soon Check Engine indicator comes on and stays on after you start the engine the fuel filler cap may not be properly installed Turn off the engine remove the fuel filler cap align the cap properly and reinstall it If you must replace the fuel filler cap replace it with a fuel filler cap that is designed for your vehicle The customer warranty may be void for an
232. te If programming a garage door opener or gate operator it is advised to unplug the device during the cycling process to prevent overheating e Continue to press and hold the HomeLink button note step 3 in the Programming section while you press and release every two seconds cycle your hand held transmitter until the frequency signal has been accepted by the HomeLink The red indicator light will flash slowly and then rapidly after HomeLink accepts the radio frequency signal e Proceed with step 4 in the Programming section 101 Driver Controls Operating the HomeLink Universal Transceiver To operate simply press and release the appropriate HomeLink button AT Activation will now occur for the trained product garage door gate operator security system entry door lock or home or office lighting etc For convenience the l hand held transmitter of the device may also be used at any time In the event that there are still programming difficulties contact Homelink at www homelink com or 1 800 355 3515 Erasing HomeLink buttons To erase the three programmed buttons individual buttons cannot AT be erased e Press and hold the two outer O HomeLink buttons until the red indicator light begins to flash after 20 seconds Release both buttons Do not hold for Z longer that 30 seconds V HomeLink is now in the train or learning mode and can be programmed
233. te control system To aid in side window defogging demisting in cold weather conditions Select 7 Set the temperature control to full heat Select A C Set the fan speed to HI Direct the outer panel vents towards to side windows an fF WH To increase airflow to the outer panel vents close the central panel vents Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop AUXILIARY A C HEATER CONTROLS IF EQUIPPED Depending upon the equipment package of your vehicle your vehicle may be equipped with auxiliary climate controls The auxiliary climate control feature provides increased capacity to quickly heat or cool the vehicle Your auxiliary climate controls are located in the overhead console of the first row seating and in the headliner of the second row seating The auxiliary climate controls are dependent on the main climate control system If the main climate control system is in the OFF position the auxiliary climate controls will not work In addition if the main climate control system is operating at a full cool temperature MAX A C or O the auxiliary temperature control becomes non functional and also operates at a full cool temperature The auxiliary unit can be controlled either by the front seat using the front auxiliary control or by the rear seat passenger using the rear auxiliary control but not both To control the auxiliary unit us
234. teering Column cee 95 Coolant checking and adding 233 refill capacities 237 260 specifications 0 0 0 263 265 Cruise control see Speed control ou 91 Customer Assistance 0005 189 Ford accessories for your VENICIO icsocscerae vans aeneweeste 223 224 Ford Extended Service PAIN aere ENE 211 Getting assistance outside the U S and Canada ceee 215 Getting roadside assistance 189 Index Getting the service you NECA sss saccsdeosssaccdesaceesssissancaassvenis 209 Ordering additional owner s literat re ispisna 216 The Dispute Settlement Board aen 211 Utilizing the Mediation Arbitration Program socso 214 D Daytime running lamps see LAMPS rorisrunrigdsosiesiaii 73 Defrost rear WINKOW uu 71 Dipstick automatic transmission PUG RAE A AEAEE 251 engine Oil srrsrissesrieiisarihh 228 Doors door ajar warning e 14 lubricant specifications 263 Driving under special conditions seseris 174 178 SANG erroei n a eG 176 SNOW and ICE oe eee eeeeeeeeee eee 179 through water eese 177 181 E Emergencies roadside Jump starting oo eee 201 Emission control system 247 Engine o cceeececceseeeseeeeeee 265 266 check engine service engine SOOM light arsson 10 Cleaning acerrima 219 c olaNt nosinis ei N 233 diesel Sacssciccsencsacestecosactssectyueewtues 6 Index fail safe coolant oo 238 idle speed control
235. tem for safety purposes If the CD DVD will not eject from the system press and hold the EJECT control for approximately 2 seconds The disc should eject whether the vehicle ignition is ON or OFF Playing a video game auxiliary device 1 Connect the video line from your video game device to the YELLOW auxiliary input jack 2 Connect the left and right audio lines to the WHITE and RED auxiliary input jacks respectively 3 Press the MODE control until DVD CD AUX no disc in player or DVD CD play disc in player illuminates in the radio display If a disc is in the system playback should begin To enable the aux inputs press the STOP control or press the AUX control on the DVD player 53 Entertainment Systems On screen indicators Lo 07 6 00 12 29 gt ai 601 En OFF gt 1En AC 3 Each time a control is pressed the operational status of the DVD player is shown on the screen The following are some possible indicators 1 CD track 2 DVD chapter 3 SYSTEM COUNTER displays current viewing time of desired media HOURS MINUTES SECONDS 4 DVD CD STATUS PLAY FF REW PAUSE 5 AUDIO OUTPUT not changeable 6 Subtitles specific language type English or Spanish dependent of disc capability and ON OFF selection 7 Camera angle of picture Adjustable with cursor controls and ENTER control Safety information Read all of the s
236. that you do not make modifications 180 Driving such as adding or removing parts such as lift kits or stabilizer bars or by using replacement parts not equivalent to the original factory equipment Any modifications to a vehicle that raise the center of gravity can make it more likely the vehicle will roll over as a result of a loss of control Ford recommends that caution be used with any vehicle equipped with a high load or device such as ladder racks or pickup box cover Failure to maintain your vehicle properly may void the warranty increase your repair cost reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off road usage DRIVING THROUGH WATER Do not drive quickly through standing water especially if the depth is unknown Traction or brake capability may be limited and if the ignition system gets wet your engine may stall Water may also enter your engine s air intake and severely damage your engine If driving through deep or standing water is unavoidable proceed very slowly Never drive through water that is higher than the bottom of the hubs for trucks or the bottom of the wheel rims for cars Once through the water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly wh
237. the Hotline 217 Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo such as Detail Wash ZC 3 A which is available from your dealer e Never use strong household detergents or soap such as dish washing or laundry liquid These products can discolor and spot painted surfaces e Never wash a vehicle that is hot to the touch or during exposure to strong direct sunlight e Always use a clean sponge or carwash mitt with plenty of water for best results e Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting e It is especially important to wash the vehicle regularly during the winter months as dirt and road salt are difficult to remove and cause damage to the vehicle e Immediately remove items such as gasoline diesel fuel bird droppings and insect deposits because they can cause damage to the vehicle s paintwork and trim over time e Remove any exterior accessories such as antennas before entering a car wash e Suntan lotions and insect repellents can damage any painted surface if these substances come in contact with your vehicle wash off as soon as possible WAXING Applying a polymer paint sealant to your vehicle every six months will assist in reducing minor scratches and paint damage e Wash the vehicle first e Do not use waxes that contain abrasives e Do not allow paint sealant to come in contac
238. the bulb straight out of the socket and push in the new bulb 4 Install the bulb socket in lamp assembly by turning clockwise 5 Install the lamp assembly and secure with four screws Replacing high mount brakelamp bulbs To remove the brakelamp assembly 1 Remove the two screws and lamp assembly from vehicle 2 Remove the bulb socket from lamp assembly by rotating it 45 degrees 3 Carefully pull bulb straight out of socket and push in the new bulb To install the brakelamp assembly 1 Install the bulb socket into the lamp assembly and rotate 45 degrees 2 Install the lamp assembly on the vehicle and secure with two screws Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper To change the license plate lamp bulbs 1 Reach behind the rear bumper to locate the bulb socket ae 2 Twist the socket counterclockwise and remove Sa 3 Pull out the old bulb from socket ee and push in the new bulb 4 Install the bulb socket in lamp assembly by turning it clockwise 80 Driver Controls WINDSHIELD WIPER WASHER CONTROLS New Rotate the windshield wiper control b to the desired interval low or high 1 speed position al a ees SO St e The bars of varying length are for SIBS Z 0 intermittent wipers When in this z position rotate the control upward A for fa
239. the ignition is turned to OFF the Family Entertainment System FES is also turned OFF When the ignition is turned ON the FES will begin playback from the last selected media source when the play control is pressed 52 Entertainment Systems e To enable or disable the FES simultaneously press the 3 and 5 memory presets on the radio face Press the presets again to disable the FES e The DVD player is only capable of reading the bottom side of a disc When inserting a single sided disc the label should be up For a multisided disc the desired play side should be down when the disc is inserted into the player e The DVD player is only capable of playback of DVDs and CDs The player is not compatible with CDR RW media e DVDs are formatted by regions This DVD system can only play region 1 DVDs DVDs manufactured in U S and Canada Do not insert any promotional discs odd shaped or discs with removable labels into the DVD player as jamming may occur which may damage your system Inserting a CD DVD Inserting a CD DVD into the DVD player automatically turns the power ON and playback should begin The counter is automatically reset to 0 00 00 Ensure that the overhead screen is down for viewing Removing a CD DVD 1 Press the STOP EJECT control to stop playback 2 Press the STOP EJECT control again to eject the CD DVD If the CD DVD is not removed within the alloted time the system will pull the CD DVD back into the sys
240. time of purchasing your vehicle you may still be eligible Please contact your dealer for further information Since this information is subject to change please ask your dealer for complete details about Ford Extended Service Plan coverage options or visit the Ford ESP website at www ford esp com THE DISPUTE SETTLEMENT BOARD U S ONLY The Dispute Settlement Board is e an independent third party arbitration program for warranty disputes 211 Customer Assistance e available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states Ford Motor Company reserves the right to change eligibility limitations modify procedures and or to discontinue this service without notice and without incurring obligations per applicable state law What kinds of cases does the Board review Unresolved warranty repair concerns or vehicle performance concerns as on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review except those involving e anon Ford product e anon Ford dealership e sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle s performance as designed e a request for reimbursement of consequential expenses unless a service or product concern is being reviewed e items not covere
241. tion is ON A reverse a sensing control allows the driver to disable the reverse sensing system only when the ignition is ON and the gear selector is in R Reverse The OFF indicator remains illuminated when the system is disabled The system defaults to ON every time the reverse gear is selected Press the control to disable or enable the system The indicator will remain illuminated to indicate a failure of the reverse sensing system Always keep the sensors located on the rear bumper fascia free from dirt snow and ice do not clean the sensors with sharp objects These elements may cause the system to operate inaccurately If the vehicle sustains damage to the rear bumper fascia leaving it misaligned or bent the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms 169 Driving FOUR WHEEL DRIVE 4WD OPERATION IF EQUIPPED J For important information regarding safe operation of this type of vehicle see Preparing to drive your vehicle in this chapter When four wheel drive 4WD is engaged power is supplied to all four wheels through a transfer case 4WD can be selected when additional driving power is desired AWD operation is not recommended on dry pavement Doing so could result in difficult disengagement of the transfer case increased tire wear and decreased fuel economy Electronic shift on the fly ESOF 4x4 system if equipped If equipped with the Electronic Shift
242. tivation Turn the ignition key to ON Press the UNLOCK button 3 times Turn the ignition key to OFF Press the UNLOCK button 3 times Turn the ignition key to ON The horn will chirp Press the LOCK button 2 times You should receive 2 horn chirps to indicate the system has been disabled or 2 chirps followed by a honk to indicate the system has been enabled ann rk WwW WHY FR Note Pressing the power door LOCK button two times again will turn the feature ON if it was previously OFF or OFF if it was previously ON Every two consecutive presses of the LOCK button after successfully entering the configuration mode will change the enable disable condition of the feature 7 Turn ignition to OFF to exit programming The horn will chirp once to confirm the procedure is complete 111 Locks and Security Sounding a panic alarm a Press this control to activate the alarm To deactivate the alarm press the control again or turn the ignition to ACC or ON Panic alarm will only operate with the ignition in the OFF position Replacing the battery The remote transmitter is powered by one coin type three volt lithium battery CR2032 or equivalent Typical operating range will allow you to be up to 10 meters 83 feet away from your vehicle A decrease in operating range can be caused by the following factors e Weather conditions e Nearby radio towers e Structures around the vehicle e Other vehicles parked n
243. top and bottom When shown on the screen it may appear as a small screen within the wide screen It may be desirable to view this type of movie in zoom mode 46 Entertainment Systems Remote control 1 REWIND control Press to reverse the direction of the DVD movie 2 FAST FORWARD control Press to advance the direction of the DVD movie 3 PLAY STOP control Press to play or stop the DVD movie 4 SEEK control Press to reverse or advance the chapter of the DVD or the track of the CD 5 DISPLAY DISP control Press to enable on screen display of player menu and user display adjustments Once the display is on use SEEK to choose the desired screen setting 6 ENTER ENT MEMORY control In DVD playback mode press the control to select a designated item in menu mode In stop mode press the control to select the next memory preset 7 MNU MODE control In DVD playback mode press to access the disc menu In stop mode press to change to rear seat mode i e AM FM CD 8 VOLUME control Press to increase or decrease volume level 47 Entertainment Systems Battery replacement Batteries are supplied with the remote control unit Since all batteries have a limited shelf life replace them when the unit fails to control the DVD player There is a LED indicator light is on the remote control which will illuminate when any control is pressed Slide the battery cover off as shown on the remote contro
244. uel Anticipate stopping slowing down may eliminate the need to stop e Sudden or hard accelerations may reduce fuel economy e Slow down gradually e Driving at reasonable speeds traveling at 88 km h 55 mph uses 15 less fuel than traveling at 105 km h 65 mph e Revving the engine before turning it off may reduce fuel economy e Using the air conditioner or defroster may reduce fuel economy e You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs Unnecessary shifting of this type could result in reduced fuel economy e Warming up a vehicle on cold mornings is not required and may reduce fuel economy 245 Maintenance and Specifications e Resting your foot on the brake pedal while driving may reduce fuel economy e Combine errands and minimize stop and go driving Maintenance e Keep tires properly inflated and use only recommended size e Operating a vehicle with the wheels out of alignment will reduce fuel economy e Use recommended engine oil Refer to Lubricant specifications in this chapter Perform all regularly scheduled maintenance items Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle scheduled maintenance guide Conditions e Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed Carrying unnecessary weight may reduce fuel economy approximately 0 4 km L 1 m
245. uld not exceed the front axle reserve capacity 182 Driving FARC Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways i e restrict the number of occupants or amount of cargo carried Always ensure that the weight of occupants cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both gross vehicle weight and front and rear gross axle weight rating limits Under no circumstance should these limitations be exceeded Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and or personal injury Special loading instructions for owners of pickup trucks and utility type vehicles For important information regarding safe operation of this type of vehicle see the Preparing to drive your vehicle section in this chapter Loaded vehicles with a higher center of gravity may handle differently than unloaded vehicles Extra precautions such as slower speeds and increased stopping distance should be taken when driving a heavily loaded vehicle Your vehicle has the capability to haul more cargo and people than most passenger cars Depending upon the type and placement of the load hauling cargo and people may raise the center of gravity of the vehicle Calculating the load your vehicle can carry tow 1 Use the appropriate maximum gross combined weight rating GCWR
246. ure operates automatically for existing conditions However AO will not be displayed in the display window If E is pressed again A will not be displayed in the display window and the EATC system will remain in AUTO operation To return to automatic recirculated air operation press AUTO Do not leave the EATC system in recirculated air operation for extended periods of time while the system is in a heating mode or in cold damp conditions as this may cause interior fogging of the front side and rear windows Manual override controls EXT TEMP The manual override controls allow you to manually determine where airflow is directed To return to full automatic control press AUTO When a manual override control is selected the EATC system will turn off the AUTO indicator in the display window and display those indicators of all of the operating controls 7s Distributes outside or recirculated air through the instrument panel registers Heating and air conditioning capabilities are provided in this mode The air will be heated or cooled based on the temperature selection For added customer comfort the system will allow some airflow through the floor ducts in this mode e P Distributes outside or recirculated air through the instrument panel registers and the floor ducts Heating and air conditioning 66 Climate Controls capabilities are provided in this mode For added customer comfort wh
247. uring the arrow on the top half of the air filter housing lines up with the notch on the bottom half of air filter housing Be careful not to crimp the filter element edges between the air filter housing This could cause filter damage and allow unmetered air to enter the engine if not properly seated 5 Replace the two halves of the air filter housing and secure the clamp INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example e Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set Tire Quality Grades apply to new pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575 104 c 2 255 Maintenance and Specifications U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it Treadwear The treadwear grade is a comparative rating based on the wear rat
248. ve anti theft system is an engine immobilization system This system prevents the engine from being started unless a coded key programmed to your vehicle is used The SecuriLock passive anti theft system is not compatible with non Ford aftermarket remote start systems Use of these systems may result in vehicle starting problems and a loss of security protection Automatic arming The vehicle is armed immediately after switching the ignition to the 3 OFF position The THEFT light in the instrument cluster will flash every two seconds when the vehicle is armed Automatic disarming Switching the ignition to the 4 ON position with a coded key disarms the vehicle The THEFT light will illuminate for three seconds and then go out If the THEFT light stays on for an extended period of time or flashes rapidly have the system serviced by your dealership or a qualified technician Key information Your vehicle is supplied with two coded keys Only a coded key will start your vehicle Spare coded keys can be purchased from your dealership Your dealership can program your key or you can do it yourself Refer to Programming spare keys 117 Locks and Security Certain items may cause vehicle starting issues e Large metallic objects e Electronic devices on the key O chain that can be used to purchase gasoline or similar items e A second key on the same key ring as the coded key If any of these items are present
249. voir 2 Engine oil filler cap 7 Air filter assembly 3 Transmission fluid dipstick 8 Engine coolant reservoir 4 Engine oil dipstick 9 Windshield washer fluid reservoir 5 Brake fluid reservoir WINDSHIELD WASHER FLUID 7 Washer fluid Check the washer fluid whenever you stop for fuel The reservoir is highlighted with a G7 symbol If the level is low add enough fluid to fill the reservoir In very cold weather do not fill the reservoir all the way Only use a washer fluid that meets Ford specification ESR M17P5 A Refer to Lubricant specifications in this chapter State or local regulations on volatile organic compounds may restrict the use of methanol a common windshield washer antifreeze additive Washer fluids containing non methanol antifreeze agents should be used 227 Maintenance and Specifications only if they provide cold weather protection without damaging the vehicle s paint finish wiper blades or washer system Note Do not put washer fluid in the engine coolant reservoir Washer fluid placed in the cooling system may harm engine and cooling system components Checking and adding washer fluid for the liftgate Washer fluid for the liftgate is supplied by the same reservoir as the windshield ENGINE OIL S27 Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil 1 Make sure the vehicle is on level ground 2 Tur
250. w high temperatures see your Ford or Lincoln Mercury dealer Fuel gauge Displays approximately how much fuel is in the fuel tank The fuel gauge may vary slightly when the vehicle is in motion or on a grade When refueling the vehicle from empty indication the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel Speedometer Indicates the current vehicle speed 49 50 go 2 f NS 30 o Y m 70 1 S 20 w 80 o 10 2 90S 9160 mn 100 KM H 17 Instrument Cluster Odometer Registers the total kilometers miles of the vehicle Trip odometer Registers the kilometers miles of individual journeys Press and release the reset button this represents the trip mode Press and hold the button for three seconds to reset Tachometer Indicates the engine speed in revolutions per minute Driving with your tachometer pointer continuously at the top of the scale may damage the engine 18 N N a GED L P Rno2i yidig 7 S 3 0 gt 2 4 Pig RPMX1000 A SL C O 06a 1 e 7 Entertainment Systems PREMIUM AM FM STEREO CASSETTE SINGLE CD VOL PUSH ON y DSC Y D OO OO E Your vehicle is equipped with a delayed accessory feature This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off or until a door is o
251. will be most accurate if your filling method is consistent Calculating fuel economy 1 Fill the fuel tank completely and record the initial odometer reading in kilometers or miles 2 Each time you fill the tank record the amount of fuel added in liters or gallons 244 Maintenance and Specifications 3 After at least three to five tank fill ups fill the fuel tank and record the current odometer reading 4 Subtract your initial odometer reading from the current odometer reading 5 Follow one of the simple calculations in order to determine fuel economy Multiply liters used by 100 then divide by total kilometers traveled Divide total miles traveled by total gallons used Keep a record for at least one month and record the type of driving city or highway This will provide an accurate estimate of the vehicle s fuel economy under current driving conditions Additionally keeping records during summer and winter will show how temperature impacts fuel economy In general lower temperatures give lower fuel economy Driving style good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy Habits e Smooth moderate operation can yield up to 10 savings in fuel e Steady speeds without stopping will usually give the best fuel economy Idling for long periods of time greater than one minute may waste f
252. y damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others 241 Maintenance and Specifications If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision which may result in possible personal injury Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage your vehicle Do not use fuel containing methanol It can damage critical fuel system components Your vehicle was not designed to use fuel or fuel additives with metallic compounds including manganese based compounds containing MMT Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty Octane recommendations Your vehicle is designed to use Regular unleaded gasoline with pump R M 2 octane rating of 87 We do not recommend the use of gasolines labeled as Regular that are sold with octane ratings of 86 or lower in high altitude areas Do not be concerned if your engine sometimes knocks lightly However if it knocks heavily under most driving co
253. y during certain frontal or near frontal collisions with sufficient longitudinal deceleration A safety belt pretensioner is a device which tightens the webbing of the lap and shoulder belts in such a way that they fit more snugly against the body The driver and front outboard passenger safety belt system including retractors buckles and height adjusters must be replaced if the vehicle is involved in a collision that results in the activation of the safety belt pretensioners Refer to the Safety belt maintenance section in this chapter Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision 136 Seating and Safety Restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver front passenger and second row outboard passengers Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder To lower the shoulder belt height push the button down and slide the height adjuster down To raise the height of the shoulder belt slide the height adjuster up Pull down on the height adjuster to make sure it is locked in place Position the safety belt height adjusters so that the belt rests across the middle of your shoulder Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in
254. ymptoms are immediately apparent The toxic effects of fuel may not be visible for hours Avoid inhaling fuel vapors Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation In severe cases excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury Avoid getting fuel liquid in your eyes If fuel is splashed in the eyes remove contact lenses if worn flush with water for 15 minutes and seek medical attention Failure to seek proper medical attention could lead to permanent injury Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin and or clothing promptly remove contaminated clothing and wash skin thoroughly with soap and water Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact could cause an adverse reaction In sensitive individuals serious personal injury or sickness may result If fuel is splashed on the skin promptly wash skin thoroughly with soap and water Consult a physician immediately if you experience an adverse reaction When refueling always shut the engine off and never allow sparks or open flames near the filler neck Never smoke while refueling Fuel vapor is extremely hazardous under certain conditions Care should be
255. you will receive an acknowledgment indicating e The file number assigned to your application e The toll free phone number of the DSB s independent administrator Your dealership and a Ford Motor Company representative will then be asked to submit statements To properly review your case the Board needs the following information e Legible copies of all documents and maintenance or repair orders relevant to the case e The year make model and Vehicle Identification Number VIN listed on your vehicle ownership license e The date of repair s and mileage at the time of occurrence s e The current mileage e The name of the dealer s who sold or serviced the vehicle e A brief description of your unresolved concern e A brief summary of the action taken by the dealer s and Ford Motor Company e The names if known of all the people you contacted at the dealership s e A description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review Oral presentations If you would like to make an oral presentation indicate YES to question 6 on the application While it is your right to make an oral presentation 213 Customer Assistance before the Board this is not a requirement and the Board will decide the case whether or not an oral presentation is made An oral presentation may be requested by the Board as well Making a deci

2002 Excursion - Hiller Ford Inc.

Contents

Download Pdf Manuals

Related Search

Related Contents