OPTIR Touch User`s Manual (32A Model) Contents: 1. The
Contents
1. amp KEYTEC INC A global leader of touch interactive technology since 520 Shepherd Drive Garland TX 75042 USA Tel 1 800 624 4289 US toll free or 1 972 272 7555 Fax 972 272 7501 Email sales magictouch com OPTIR Touch User s Manual 32A Model Contents 1 The Components 2 Standard Sizes 3 Available Packages 4 Frame Assembly 5 Custom Size Configuration How to make it re sizable 6 Driver Installation 7 Touch Screen Functions 8 Setting and Options 9 Troubleshooting and Technical Support Introduction OPTIR Touch 32A Model sensor board width 32 mm A creative solution for large size touch interactive screens Standard sizes are from 26 to 65 Custom sizes are available up to 140 Simple USB interface compatible with Windows 7 Vista XP 2000 Intel Mac and Linux Advantages 1 The sensor components can be reused and resized to different sizes and aspect ratios 2 Maximum clarity no added overlay except protection glass if needed 3 Light touch no pressure is needed can be activated by finger gloved hand or stylus 4 High durability 100 solid state electronics no moving parts involved 5 Do it yourself kit can be shipped at minimal cost comparing to shipping a large touch screen 6 Flexible purchasing options 1 components only for DIY assembly or 2 framed segments unassembled frames or 3 finished assembly with protective glass Update July 272. USB cable to re initiate the controller 6 7 Double click Touch USB icon to open touch control panel 6 8 Click the calibration button choose either 5 or 25 point calibration then click GO Touch the center of each circle and hold for 2 seconds then lift off to complete the calibration 6 9 Repeat the calibration if necessary Click OK to close the window 6 10 If you have Vista or Windows 7 OS there are the options of using touch screen as mouse or tablet by clicking the desired button in Touch USB control panel In tablet mode the touch response is usually slower but Windows 7 dual touch feature can be performed 7 Touch Screen Functions 7 1 Screen touched left mouse button clicked 7 2 Touch down and drag left mouse button held down and dragged 7 3 Tap twice left mouse button double clicked 7 4 Swap Button Select once to right click for one touch or always to always right click Select minimize to reduce to system tray Click in tray as a shortcut 8 Settings and Options 8 1 Mouse speed Control the tracking speed of mouse cursor 8 2 Double click speed Control the time interval between two clicks to activate a double click Slow speed makes double click easier Test the double click by tapping the K logo twice If successful the logo rotates 8 3 Lift Off When this option is enabled the click is activated when touch is lifted away from the touch screen This mode is very useful for click
3. mm 4 5 13 For 65 assembly 3 16 thick 56 3 4 x 32 3 16 5 mm thick 1441 x 818 mm 4 5 14 For 103 assembly 3 16 thick 89 15 16 x 50 15 16 5 mm thick 2286 x 1296 mm After the glass is placed in position a set of holders should be screwed or adhered to the back of the frame to hold the glass Note Using tempered glass is highly recommended Note The metal glass holders at the 4 corners should be screwed onto the frame using type b screws The rest of the metal glass holders should be fixed by using black rivets into the holes on the frame Since the holders are designed for 5mm thick glass there will be a gap when using 3 mm thick glass A 2mm thick tape should be added between the holder and the glass to prevent the glass from moving 26 to 47 These two glass holders are to provide extra protection during transportation and should be removed after delivery before installing hangers These two glass holders are to provide extra protection during transportation and should be removed after delivery before installing hangers 4 6 Assemble the hangers There are 4 positions where the hangers can be fixed For most displays the hangers should be inserted into the bottom holes but they can be moved to upper holes if the touch screen seems to be above the view area of the display after mounting Use type c screws to secure the hangers to the back of the frame 4 6 1 Adjust the hangers
4. 2012 1 The Components All measurements are in mm 1 mm is approximately 0 04 All circuit boards are 32 mm wide 9 mm high A universal external power adapter is included 2 Standard Sizes All measurements are in mm 1 mm is approximately 0 04 Maximum tolerance 2mm pO 1829x748 1331 2 748 8 1402x8196 1406 x 823 6 103 special order Custom sizes can be arranged Maximum size 140 USB interface Resolution 4096 x 4096 Compatible with Windows Mac Linux Components for making 103 model are special type so a special order is required 3 Available Packages 3 1 Components Only Customers can purchase the components only for their own integration Upon receiving the active area dimensions from customer we will assemble the components to be as close as possible to the dimensions specified and test the functionality A configuration drawing will be generated for customer to follow to complete the assembly Each circuit board will be labeled with serial number and packed into a box 3 2 Framed Segments are unassembled frames Customers can purchase the frame segments which already have the components assembled inside When they receive the segments they will just need to join the 4 segments with corners as labeled They can also add a piece of glass or Plexiglas to the back of the frame for protecting the display and optimizing the functionality The IR filter is included with frame See sectio
5. hose parts with part number that cannot be evenly divided by 4 only one piece can be used on each side and they must be placed next to the corner as shown in the following figure The 3 corners must be assembled in the positions as shown in the figure The controller IRM64B is required and a IRT 64 is also required at the opposite frame The following is the assembly configuration of 103 The components IRT31 IRT37 IRR31 IRR37 cannot be divided by 4 so only one piece can be used on each side and must be placed next to the corner 1355 27 mm 1264 4 mm comer aco aea weno meee vere ene nee je 2272 4 mm 2343 2 mm 6 Driver Installation 6 1 A USB controller and Windows 2000 XP Vista 7 driver are included Mac driver is included only when the Mac version is purchased 6 2 Insert the driver CD into CD Rom 6 3 Click to select USB controller then click install button 6 4 When prompted for plug into the controller plug the controller into USB port Windows shows found new hardware message Click OK to continue 6 5 When prompted for restart the Windows click OK to reboot 6 6 After Windows is rebooted two new icons are created on desktop a Touch USB F Swap Button At this point the LED on the controller should be on and IR screen should respond to touch but the position of touch is not accurate until the screen is calibrated If the IR screen is not responding to touch unplug and re plug in the
6. ing hyperlinks such as Internet browser or programs that use mouse over function However it is impossible to drag or draw in this mode 8 4 Beep Enable disable an audio beep when touching the touch screen 8 5 Move only Touching and dragging only moves the mouse cursor without performing a click This option is for those who have an optional click pen currently unavailable 8 6 Hide cursor Makes the cursor invisible preferred for some applications 8 7 Uninstall Click to uninstall the driver 8 8 Default setting Return the speeds and options to the original settings 9 Troubleshooting and Technical Support 9 1 Make sure the driver was installed first before the USB controller is plugged into a USB port 9 2 Make sure the power supply is plugged into the controller next to USB cable connection 9 3 Make sure the controller always plugged into the same USB port 9 4 Make sure the sensors are leveled and the corners are right angled If the problem persists contact KEYTEC S tech support Email to tech magictouch com or call 972 272 7555 8 30AM to 5 00PM CST M F Must obtain an authorized RMA return merchant authorization from tech support department before returning the product for service
7. n 4 for assembly instruction 3 3 Assembled Frame The IR touch screen is fully assembled as shown in the following picture except the hangers will be installed by the customer to the desired position A piece of tempered glass is mounted at the back of the frame 4 Frame Assembly 4 1 The frame assembly includes the following parts The screws Type a Screws for the frame assembly 3mm x 4mm Type b Screws for the backing glass holders 3mm x 6mm Type c Screws for installing hangers to frame 3mm x 8mm Type d Screws for connecting 3 hanger pieces 4mm x 6mm Rivets Velcro Pads Rubber Pads Metal Glass Holders 3 pc Hangers IRH 3P USB Cable Power adapter 4 2 There are four segments that need to be assembled 4 2 1 r Two shaped frames one labeled with letters A and B one labeled with letters C and D 4 2 2 Two straight frames one labeled with letters A and C one labeled with letters B and D 4 2 3 The segments should be connected by matching the letters as shown in the following Backside View Important Make sure the pins are plugged into the female connector correctly Do not bend the pins Use type a screws to secure the assembly Longer screws will damage the inner PCB components 4 3 Plug in the USB cable and power adapter to the right lower corner of the frame assembly Then connect the USB cable to a PC If the yellow LED first blinks then stays on
8. that means the assembly is successful Otherwise the connections between the segments may need to be checked and adjusted 4 4 The OPTIR Touch can now work as is but adding a piece of glass or Plexiglas in the middle of the frame is recommended for better functionality and added protection to the display 4 5 The recommended glass sizes are listed in the following 4 5 1 For 26 assembly 1 8 thick 23 3 8 x 13 1 2 3mm thick 594 x 343 mm 4 5 2 For 30 assembly 1 8 thick 26 5 8 X 14 15 16 8mm thick 676 x 379 mm 4 5 3 For 32 assembly 1 8 thick 28 1 16 x 16 1 8 3 mm thick 712 x 411 mm 4 5 4 For 37 assembly 1 8 thick 32 13 16 x 18 11 16 3 mm thick 833 x 475 mm 4 5 5 For 40 assembly 1 8 thick 35 7 16 x 20 1 4 3 mm thick 900 x 514 mm 4 5 6 For 42 assembly 1 8 thick 37 x 21 1 16 3 mm thick 941 x 536 mm 4 5 7 For 46 assembly 1 8 thick 40 3 4 x 23 3 16 x 1 8 3 mm thick 1035 x 589 mm 4 5 8 For 47 assembly 1 8 thick 41 7 16 x 23 9 16 3 mm thick 1053 x 598 mm 4 5 9 For 50 assembly 3 16 thick 44 1 2 x 25 1 16 5 mm thick 1130 x 637 mm 4 5 10 For 52 assembly 3 16 thick 45 7 8 x 26 5 mm thick 1165 x 660 mm 4 5 11 For 55 assembly 3 16 thick 48 9 16 x 27 11 16 5 mm thick 1233 x 703 mm 4 5 12 For 60 assembly 3 16 thick 52 15 16 x 29 15 16 5 mm thick 1345 x 760
9. to suitable position and tighten them with the screw Hanger Assembly IRH 3P IRH 3P allows for multiple adjustment options to have a better fit on variety of displays Using the screws provided you may connect the 3 pieces as shown below Type d screws 4mm x 6mm iS 75mm 7Omm Overall Inner Dimension 78mm Front Figure 1 3 Piece Individual Parts Figure _ 3 Top view of one side Maximum display thickness allowed 70mm Type c screws 57mm 45mm Overall Inner 3mm x 8mm Dimension one 89mm 4mm T mm T mm Inner Front Dimension Figure 2 Top view of one side FIGURE 4 Side View Minimum display thickness allowed 45mm FRONT attaches to IR Frame 4 6 2 Hang the touch screen on the display and assemble the other set of hangers to suitable position 4 6 3 The completed mounting structure is shown here in the following 4 7 After finishing the assembly you may add the Velcro pads to the hangers and lower part of the back of the frame to secure the mounting Add the rubber pads to the back of the frame to prevent the scratching on the surface of display housing Please see the following sketches about adding those pads 5 Custom Size Configuration How to make it re sizable The rule of thumb is all the parts with part number that can be evenly divided by 4 are re sizable parts which can be assembled in any sequence For t
Download Pdf Manuals
Related Search