GSM Wireless Alarm System
Contents
1. surveillance system GSM Wireless Alarm System Area Une Herreg ll mm gt em EI GE N A H 5 E 2 3 SET BT ESC ENT Model G70D GT GTW Installation amp Operating Manual Shenzhen Meidasi Technology Development Co Ltd Thank you for choosing ak UNIFORE y surveillance system Please read this guide thoroughly and carefully before applying the system in use Keep this manual safe for future reference Copyright Notice This manual is furnished under license and may be used or copied only in accordance with the terms of such license Except as permitted by such license no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or any means electronic mechanical Recording or otherwise including translation to another language or format without the prior written permision of Unifore Security The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Unifore Security Unifore Security assumes no responsibility or liability for any errors or inaccuracies that may appear in this book All other product names trademarks and registered trademarks in this document are the properties of their respective holders Warranty Unifore Security warrants this product will be free from defects in materials and workmanship for period of time specified on the product packaging2. 3 Did not match to the main host 2 5S detect once every 5 seconds 5MIN detect once every 5 minutes 3 Match the sensor to the main host according to Program Sensors instruction The detecting distance of PIR sensor 1 The ambient temperature is It is normal that when the ambient temperature in the gets shorter too high detecting area exceeds the human body temperature the 2 Low battery detecting distance will get shorter The host does not alarm after the Failed to follow the operation new added wireless detector is instruction of Program Sensors triggered to add the new wireless sensor ie a Low battery Replace with new batteries of the same specification The door magnetic sensor indicator flashes frequently in green after Low battery Replace with new batteries in the same specification alarming Wie pital of the ramote controller Le battery Replace with new batteries in the same specification The host does not alarm after the Failed to follow the operation new added wireless detector is instruction of Program Sensors triggered to add the new wireless sensor Follow the operation instruction of Program Sensors to activate the new wireless sensor Follow the operation instruction of Program Sensors to activate the new wireless sensor Wired Accessories Connection Instruction How To Connect Wired Sensors To The Main Alarm Host e Normal Closed NC type sensors Add 2
3. The system has up to 60 seconds of Entry and Exit delay functions No signal from any sensor will be able trigger an alarm until the Exit delay is expired This provides enough time for user to exit the property without triggering an alarm If the user leaves the property after the Exit delay the system will enter the Entry delay countdown and user will need to enter the user code to disarm the system and avoid triggering an alarm If the Entry delay function is disabled for the certain zone an alarm will be triggered immediately once the system is armed System History Records The system is capable of storing up to 100 alarm records and 100 Arm Disarm records This enables the user to review the time and date an alarm is triggered and when the system is Armed Disarmed With E2PROM data management the system is capable of retaining programming settings and event logs after power is disconnected Touchpad control with LCD illumination display The system has a stylish touchpad control panel that displays status information time and date in large clear letters Chime Function lf a sensor is allocated to the Chime zone and the sensor is triggered when the system is in standby mode the Main Alarm Host will produce a few bi sound to alert the user that a door or a particular area has been entered A Large Range Of Advanced Accessories With the auto learn sensor function the system is capable of adding many different accesso
4. This limited warranty shall commence from the date of purchase Unifore Security products warranty is not transferable and is limited to the original purchaser If the product is found to be defective then as your sole remedy and as the manufacturer s only obligation Unifore Security will repair or replace the product The warranty shall not apply to products that have been subjected to abuse misuse abnormal electrical or environmental conditions normal wear and tear or any condition other than what can be considered normal use Limitation of Liability The liability of Unifore Secuity arising from this warranty and sale shall be limited to a refund of the item price In no event shall Unifore Security be liable for costs of procurement of substitute products or services or for any lost profits or for any incidental consequential direct or indirect damages however caused and on any theory of liability arising from this warranty and sale These limitations shall apply not withstanding any failure of essential purpose of any limited remedy Foreword The G 0D GT GTW Wireless Alarm System is designed to provide a high standard of security protection for your home and office The system is configured for ease of installation and operation However it is strongly recommended to read and fully understand the advice and installation procedures contained in this manual before proceeding with the installation and operation of your G70D GT GTW
5. e Bypass Zone This setting is to enable or disable a zone bh A or Y button ENT Choose YES to bypass disable the sensor choose NO to keep this zone s sensors working Default is NO Entry Delay Set This setting is to enable or disable entry delay for the zone b A or Y button ENT Choose YES if you want the sensors in this zone to have entry delay choose NO if you want the alarm to goes off immediately when any of the sensors in this zone is triggered regardless of the entry delay time setting Default is NO Set Smart Zone This is a brand new feature in G70 system The smart sensor recorded in the system can determine if a door window is opened or closed upon arming lf the Main Alarm Host detects a door with smart sensor is opened the system arm status will flash to indicate You will be asked if you want to continue to arm anyway VS WPWMC To order please visit our company website at NOTE Only workable with the Wireless Smart Door Sensor MN www hkvstar com In program mode when Set Smart Zone is displayed ENT WM Use button to delete any old record select a desired Smart Zone Number XX ENT k A or Y button to select YES or NO on the menu ENT Choose YES to set the zone as a smart sensor zone Choose NO to keep the zone in normal working mode Default is NO for all zones The Main Alarm Host then requires you to confirm whethe
6. 2K Ohms resistor Sensor with self power supply 12Vdc Ground Zone 31 Zone 32 Zone 33 Zone 34 Zone 35 Zone 36 Without Self Power Zone 37 Zone 38 Sensor without self power supply Wired Sensor Sensor with self power supply 12Vde Ground va et L Wired Sensor i A Main Host Zone 31 A Zone 32 Zone 33 Zone 34 Add 2 2K Ohms resistor Zone 35 zone 36 5 _ C zone 37 Langen S P A d a i i Without Self Power a A E w EON Zone 38 Sensor without self V1 F power supply D GND 2 OK Al ian Wired Sensor Main Host L ee _ es ee Quick Guide on How to Activate Deactivate Wireless Accessories Sensor Type How to activate How to deactivate Remote Keypad Zone 00 01 Remote Zone 00 01 Wireless door sensor Wireless smart door sensor Wireless Wide Angle PIR sensor Wireless Curtain PIR sensor Wireless Gas detector Wireless Smoke Sensor Wireless Indoor siren Wireless Outdoor Siren 1 SET Password A or Y Program sensor ENT lL Zone Number Y Y ENT 4_ Group Number X ENT A or Y Activate Sensor Zone Number Y Y ENT 4i_ ENT Learning will be shown Groupd Number X ENT A or Y 2 Press on the remote twice successively the Delete
7. General System Information On G70D GT GTW This device is a part of the Unifore Security home control system and works with the bi directional wireless protocol All devices are delivered in a standard configuration All current technical documents and updates are provided at www hkvstar com Should you encounter any difficulty in the set up or operation of your security system firstly refer to the Common Problems and Solutions guide at the rear of this manual In the unlikely event of a problem occurring with your G70D GT GTW switch off at the mains sockets pull out the plugs and contact your dealer immediately General Information On Radio Operation The radio transmission is on a non exclusive transmission path with possibility of interference occurring Other interfering sources can be caused by switching operations electrical motors or defective electrical devices The range of transmission within buildings can greatly deviate from open air distances Besides the transmitting power and the reception characteristics of the receiver environmental influences such as humidity in the vicinity and local structures also play an important role Compatibility Of This Manual This manual should be used with G70 G70E G70D Series only CE amp FCC Compliances Statement CAUTION Changes or modifications without approved by Unifore Security could void your authority to use this equipment This equipment has been tested with the liste
8. into a suitable indoor mains socket at a height above 1 8 meters Smoke Detector 1 Use the mounting bracket to mark two drilling holes on the wall Drill the holes and fit two screws provided to fix the bracket NOTE Do not drill the fixing holes with the AN bracket in position The power tool may cause damages to the bracket 2 Remove the battery cover and connect the provided battery to the battery clip Mounting Bracket 3 Refit the battery cover Slide in the detector and rotate clockwise to lock the detector onto the mounting bracket System Luminous Signal Indicators Alarm control panel ll Wm di mmm 9 em e ul en On No GSM network detected or SIM card not available Flashing GSM detected Slow flash 200ms on 2s or 3s off indicates the Main Alarm Host is in standby mode Fast flash 200ms on 600ms off indicates the Main Alarm Host is dialing the programmed numbers DI On Armed Home or Away Flashing Smart sensor open detected Off Disarmed y mm On AC connected normal Flashing Working with backup battery Off Low backup battery Wireless Remote Keypad Tei Le Ch A When the Main Host is armed as Armed Home mode light will turn on together with the e light A e When the Main Host is armed as Armed Away mode only light will turn on Ze On AC connected normal Flashing Working with backup battery Off Low backup batter
9. is that it gives authority to the administrator only to modify items in Set while other users in the same premises can only use Arm and Disarm operations from the Wireless Remote Keypad To modify the user prog code on the Wireless Remote Keypad k SET Master Password Default is 999999 ENT Select between User Code and Prog Code enter the current password ENT Enter a 6 digit new code ENT and re enter the new code ENT for confirmation NOTE The Master Password 999999 for changing the user prog codes could not be changed Recording Playing A Message Your G70 has a built in microphone and loudspeaker on the Main Alarm Host The recorded message is used for playback in an alarm event To record a message Press and hold the record button located at the back of the Main Alarm Host and speak closely to the mic hole located on the panel Release the button once finish recording The system can store a 10 seconds long message To play a message Press the play button located at the back of the Main Alarm Host and you can hear the recorded message Upon receiving the call from the system after an alarm was triggered the recorded voice message is played immediately for 30 seconds repeatedly User could select from the following options Press 8 to enter into the listening status for 20 seconds you can hear the alarm background sounds from phone Press to play the recorded vo
10. receive status information from Main Alarm Host NOTE The original Wireless Remote Keypad that is shipped with your G70 system will be automatically registered to the Main Alarm Host Unless you made any changes to the Wireless Code on the Main Alarm Host or Wireless Remote Keypad or both re matching the Wireless Remote Keypad to the Main Alarm Host is not required Activating the Synchronization To activate in program mode when Main Unit Sync is displayed k ENT Use the A or Y button to choose Activate ENT The word Learning will show on the LCD Screen trigger the Main Alarm Host followed by disarming on the Main Alarm Host the word Success will show on the LCD screen once the Wireless Remote Keypad receives the signals from the Main Alarm Host Deactivating the Synchronization To delete in program mode when Main Unit Sync is displayed lr ENT Use the A or Y button to choose Delete ENT The word Success will show on the LCD screen Wireless Code In program mode when Wireless Code is displayed fy ENT d Use button to delete old record then set XXXXXXXX ENT XXXXXXXX 8 digits digits range from 0 1 or 2 Default is 11111111 NOTE You do not need to change this code if there is no nearby user using the G70 system If you change this code after matching the Wireless Remote Keypad to the Main Alarm Host then signal could not be transferred to the Main Alarm Host again You h
11. remotes supports up to 4 Wireless Remotes or Wireless Remote Keypads per zone In program mode when Zone Attribute is displayed b ENT 41 Use button to delete any old record XX 2 digit Zone Number between 02 38 ENT Zone Type The system must be allocated into one of the following 3 zones e Perimeter Outer Zone Defense Generally use for detecting area such as doors windows etc Wireless Door Sensors and Wireless Curtain PIR Sensors are normally allocated into this zone e Motion Inner Zone Defense Generally use for detecting area such as living room aisles and bedrooms etc Wireless Wide angle PIR Sensors and Wireless Door sensors are normally allocated into this zone e Emergency This zone monitors the system status for 24 hour and is usually used for emergency distress medical rescue gas leakage smoke and fire alarm etc Sensors including Panic Button Wireless Gas Sensors and Wireless Smoke Detectors are normally allocated into this Zone bh A or Y button to select the Zone Type ENT Three types 2 means Motion zone 1 means Perimeter zone 0 means Emergency zone Alarm Type The corresponding sensor name will then show on the LCD and SMS when alarm is triggered Alarm Type 20 is specially allocated for door bell function fy ENT JIL Use button to delete any old record XX ENT XX 2 digit you can set 00 15 or 20 for valid Alarm Type 13 14 Taam e o o n e o e
12. 4 meters Drill the d Wall S Ba holes and fit two screws provided to fix the a bracket d d j NOTE Do not drill the fixing holes with the bracket in i JN poston The power tool may cause damages to the p bracket 2 Undo and remove the screw located at the bottom a edge of the Sensor Open the sensor shell to remove jumper for a detection frequency of every 5 minutes 3 Connect the battery supplied to the battery clip Learning Emitting Switch Refit the cover and fixing screw Sensor rer oo ax Ai a 10371 371 LF i a k i 4 Slide the PIR sensor into the bracket Adjust the power switch S sensor to an angle that the movement of an intruder ich IR P d would cut across the device Jump Line E an 5 Connect the PIR sensor to battery and the unit will enter into the normal working state after 30 seconds Wireless Door Sensor 1 Slide off the battery cover and place the provided battery into battery holder with facing upward and refit the battery cover 2 Attach the adhesive pads onto the back of the magnet and detector 3 Mount the detector on the frame and the magnet on the opening part at a height of at ole Mounting Bracket least 1 6 meters 5l O NOTE The magnet must be 8 aligned on the LEFT side parallel sses nig toni to the detector and within 10 mm to the sensor when the door Ol o Sien window is closed Indoor Wireless Siren 1 Plug the Internal Siren
13. Sensor ENT main host LCD will display Success 2 The alarm host will beep once and press ESC to exit Same as above 1 SET Password A or Y Program sensor ENT Ml 1 Same as above 2 Press on the remote twice successively the main host LCD will display Success 1 Same as above Sama ae seis 2 Trigger the door magnet sensor twice successively 1 Same as above 2 Trigger the door magnet sensor twice successively 3 Go to Set Smart Zone to activate smart zone 1 After connecting to the power keep pressing the Learning switch on the side of the siren for 5 seconds and release light on the siren flashes 2 times and then off indicate successful deactivating 1 Same as above 2 Trigger the PIR sensor by pressing Learning Emitting Switch on the panel twice successively 1 Same as above 2 Trigger the PIR sensor by pressing Learning Emitting Switch on the panel twice successively 1 Same as above 2 Trigger wireless gas alarm by releasing gas the host LCD will display Success 1 Same as above 2 Trigger wireless smoke alarm by releasing smoke the host LCD will display Success 1 After connecting to the power press the Learning switch on the side of the siren 2 Press Ji key on the alarm host not the remote to sound off the siren then disarm by using the alarm host keypad ESC Password ENT the alarm host will beep twice to indicate the indoor siren has
14. and the time shown on the Main Alarm Host will be 14 21 20 For invalid time it cannot be saved by pressing ENT Set Date In program mode when Set Date is displayed bh ENT M Use button to delete the old record then input YYMMDDW ENT YYMMDDW 7 digit meaning year YY month MM day DD week W 0 means Sunday For example 17th December 2012 Thursday you may press 1212174 and the date shown on the Main Alarm Host will be 17th December 2012 Thursday Auto Dialer Number To set the reporting telephone numbers or reporting SMS First Auto Dialer Number is for Call Center use and the remaining Auto Dialer Numbers are for Personal Numbers Call Center Report to a Call Center with Ademco CID protocol or a specified number to report status of the system Arm Disarm Alarm AC Failure Please note you will also need to enable the Upload Status function See Upload Status below for detailed operations Personal Number Only reports when system is in alarm Call By Phone For Voice alarming When system is in alarm it will dial the pre installed numbers SMS Reporting For SMS alarming If you choose SMS Reporting system sends a SMS message to the telephone numbers with GSM but not to land line numbers In program mode when Auto Dialer s is displayed ENT Wi Use button to delete the old record then input the 1st telephone number ENT b A or Y button to select the repor
15. ave to re match the Wireless Remote Keypad or change back to the previous wireless code for them to work Reviewing Alarm Status History The system could memorize up to 100 records both for the alarm and status history User could review the alarm and status history one by one when needed NOTE The system will automatically replace the oldest events log once the records are filled up Alarm History In program mode when Alarm History is displayed bh ENT Use A or Y button to view record ENT Status History In program mode when Status History is displayed k ENT Use A or Y button to view record ENT Daily Maintenance and Care This alarm is a hi tech product with the outstanding design and sophisticated technique and shall be used carefully To make the alarm to operate for a long term stably and to prolong the service life it is recommended that Try to put the Main Alarm Host in a dry and well ventilated location Do not put the Main Alarm Host and any wireless detectors in too cold too hot or dusty places to prevent it from curtailing the service lives of electric parts and preventing the plastic shell from distorting Do not put the Main Alarm Host and any wireless detectors in low and too exposed places to prevent children from touching them or the thieves from finding them Regular testing is necessary for finding and resolving problems in time Regularly check the batteries in all wireless sensors The se
16. been successfully disarmed 3 The siren light will flash 5 times and then off indicates successful activating Same as wireless indoor siren Same as wireless indoor siren Unifore Security reserves the right to change and modify the product design and specifications without notice All materials have been carefully proofread to ensure accuracy Unifore Security holds no responsibility for consequences caused by printing missing or translation errors on this manual 2010 by Unifore Security All rights reserved www hkvstar com G70 Manual Rev 03 Design in Shenzhen
17. d out of children reach i e Place it at a height above 1 5 meters e Locate your Main Alarm Host and Wireless Remote Keypad within a protected area Le Any intruder must open a protected door or pass through a PIR sensor when the system is armed e The selected location for the Main Alarm Host must have a good GSM signal and for G70 models G70 GT GTW with telephone based functions it must be situated within reach of a telephone point e Avoid mounting the Main Alarm Host and Wireless Remote Keypad close to any metalwork i e Radiators water pipes etc as the radio range of the device could be affected Installing The Main Alarm Host and Wireless Remote Keypad Antenna Connection Screw the antenna by hand onto the Main Alarm Host until firmly attached SIM Card Connection SIM Card before use Do not insert or remove SIM card when A NOTE Clear ALL password messages and contacts on the the system is powered by AC power or Battery Insert a valid GSM SIM card in correct direction into the SIM Card Slot located at the rear of the Main Alarm Host Phone Line Connection G70 GT G70 GTW Only Connect one end of the telephone line cord into the Main Alarm Host and the other end of this cord into the wall jack Power Connection NOTE Use only the G70 power supply provided with your system The Main Alarm Host and Wireless Remote Keypad AN have different power adapter in their packing box please be careful not to apply the wron
18. d standards below and found in compliance with the LVD Directive 2006 95 EC and the EMC Directive 2004 108 EC It is possible to use CE marking to demonstrate the compliances C E EN 301 489 1 V1 8 1 NATO EN 301 489 7 V1 3 1 EN60950 1 2006 A11 2009 A1 2010 EN50131 This product complies with FCC PART 15B 22H 24E and the E operation is subject to the following conditions d EC z E D 1 This device may not cause harmful interference and ES E 2 This device must accept any interference received sd RoHS Safety Instructions Before using this product please read and understand the Safety Instructions thoroughly to ensure correct usage and follow all the instructions Symbols Special Notes Please read carefully Keypad Control Command Follow carefully to operate system correctly Always follow the manufacturers advice when using power tools ladders etc and wear safety goggles and ear defenders when drilling holes It is strongly advised to check for hidden electricity and water pipes with a cable pipe locator before drilling holes in the desired mounting surfaces Mounting all devices in dry interior locations only and away from metalwork e radiator water pipes etc Given the high sound level produced by the Siren when working in close proximity to this device it is important to wear ear defenders to avoid hearing loss Do not overload wall outlets and extension cords as this ca
19. de ENT Idi Use button to delete any old record then set XXXXX 5 digit unique wireless code between 00000 99999 Default is 00001 ENT Programming Wireless Remote Control Entering The Program Mode Menu Access to the Program Mode menu on the Wireless Remote Keypad is protected by a Prog Code default 888888 To enter the program mode b SET Enter code default password is 888888 ENT Program Mode Main Menu set Time b A or Y button to choose from the following Set Date Main Unit Sync NOTE VS WJP2 Wireless Remote Keypad is Wireless Code double password protected and operates with a user code for ARM DISARM and a prog code for SET operations Default user and prog code is 111111 and 888888 respectively Time Date Settings set Time In program mode when Set Time is displayed h ENT Mi Use button to delete the old record then input HHMMSS ENT HHMMSS 6 digit meaning hour HH minute MM second SS each takes 2 digits space For example 14 21 20 you may press 142120 and the time shown on the Main Alarm Host will be 14 21 20 For invalid time it cannot be saved by pressing ENT Set Date In program mode when Set Date is displayed k ENT EIN Use button to delete the old record then input YYMMDDW ENT YYMMDDW 7 digit meaning year YY month MM day DD week W 0 means Sunday Main Unit Synchronization This option allows the Wireless Remote Keypad to
20. e the previous Group Number then set X ENT X 1 digit for valid operation you can set a Group Number from one of the followings 0 1 2or 3 Activating Updating A Sensor To activate a sensor k A or Y button to select Activate Sensor ENT Note If the word Update shows on the screen it means this sensor has already been added before choose Yes to override MN the previous setting for this sensor in the system or No to keep the setting unchanged Deactivating A Sensor To deactivate a sensor follow the same procedure and select Delete Sensor ENT This option allows you to delete the added sensors from the Main Alarm Host The words Deleting Success will show on the LCD Screen which means you have deleted the sensor successfully from the system Wireless Code This option allows user to change the unique wireless code for transmission on the Main Alarm Host It is used so that every G70 Main Alarm Host can have a different transmission code to avoid unintentional transmission to your neighbor s G70 system NOTE You do not need to change this code if there is no nearby user using the G70 system If you change this code after matching AN ee accessories to the Main Alarm Host you will need to re match the accessories or change back to the previous wireless code for them to work b b b SET Enter User Code default password is 888888 ENT A or Y button to choose Wireless Co
21. ectly the Main Alarm Host will return back to the standby mode Stopping An Alarm Without Disarming The System If an alarm was triggered by an intruder and providing a valid GSM SIM card is present the system will automatically contact the programmed telephone numbers in the system Upon receiving the call user could stop the alarm by pressing the button The system will remain Armed and stop dialing the next auto dialer number Forced Arming Smart Sensor When Arming the system if a protected zone is programmed to be a smart zone With Smart Door Sensors VS PWMC only The Main Alarm Host Wireless Remote Keypad will flash to indicate a zone is disturbed You will be asked if you want to continue arming the system If you choose YES the system will arm with the smart zone bypassed and the protected site will not have maximum protection Setting Your Passwords Main Alarm Host G70 Main Alarm Host employed a User Code for Arm default is 888888 To modify the user code on the Main Alarm Host Disarm and Set operations bh SET Master Password Default is 999999 ENT Enter a 6 digit new code ENT and re enter the new code ENT for confirmation Wireless Remote Keypad The Wireless Remote Keypad VS WJP2 also has a User Code for Arm and Disarm operations default is 111111 but uses a Prog Code for Set operation default is 888888 The reason for this arrangement
22. es and 8 wired zones Each zone could be independently allocated into one of these types e Perimeter Outer Zone Defense Generally use for detecting area such as doors windows etc Wireless Door Sensors and Wireless Curtain PIR Sensors are normally allocated into this zone e Motion Inner Zone Defense Generally use for detecting area such as living room aisles and bedrooms etc Wireless Wide angle PIR Sensors and Wireless Door Sensors are normally allocated into this zone e Emergency This zone monitors the system status for 24 hour and is usually used for emergency distress medical rescue gas leakage smoke and fire alarm etc Sensors including Panic Button Wireless Gas Sensors and Wireless Smoke Detectors are normally allocated into this Zone Bypass Zones With the bypass sensor function a zone could be omitted upon arming Any sensors allocated to the bypassed zone will not be protected and will not trigger an alarm Remote Phone And SMS Control It is possible to gain basic control Arming Disarming the system over the system by dialing into the system or by sending a SMS message You may also activate the microphone on the Main Alarm Host to Listen In to what is happening in the protected property With a personal number set to the 1st Caller number and upload status is enabled an SMS notification message will be sent to the user to confirm a status change of the system when conducted remotely Entry Exit Delay
23. g adapter Apply AC DC power to the system with the power adapter provided Connect to AC100 240V 50 60Hz Plug the connector into the rear of the Main Alarm Host Same for the Wireless Remote Keypad Backup Battery Charging A rechargeable Li lon battery is installed in the Main Alarm Host To recharge turn on the battery switch located beside the power connector Same for the Wireless Remote Keypad Check GSM Signal Level In standby mode b A or Y button on the Main Alarm Host GSM Signal Level AX YY XX is the signal level 2 digit OO 31 indicates the signal from weak to strong 99 indicates unknown YY is the signal status display either OK or NO OK means the signal is fine and the host is working properly NO means the signal is weak and user should adjust the installation place of the Main Alarm Host If the SIM card is not present or not correctly installed then the panel will show NO SIM CARD NO SIM CARD XX YY b ESC to exit or the system will exit automatically after 30 seconds Wireless Remote Overview And Hints The Wireless Door Sensor comprises of a sensor and magnet With the magnet normally mounted on the door windows and the sensor mounted to the frame the Wireless Door sensor is designed to send a signal to the Main Alarm Host in order to trigger an alarm in Armed mode upon the protected door or window is opened When us
24. he G70D security alarm system We strongly recommend you read the manual before using your system System Arming Your G70D is controlled by a Main Alarm Host designed to collect data from sensors located within the protected site The system provides user with protection options of Armed Home and Armed Away Armed Home will arm all zones while the Armed Away will only arm the Perimeter zone An alarm is triggered upon detection of disturbance in any one of the armed zones Sensors and detectors set to the Emergency zone could also trigger an alarm regardless of the system is being armed or disarmed SMS Alert Phone Call To Preset Numbers And Call Center In the event of alarm being triggered the system will automatically report the event via SMS alert if GSM is available or phone call to the Call Center and preset telephone numbers in the dialing sequence until an acknowledge signal is received User and Master Codes G70D Main Alarm Host employs a 6 digit User Code for Arm Disarm and Set operations Wireless Remote Keypad is double password protected and operates with a 6 digit User Code for Arm Disarm and a 6 digit Prog Code for Set operations It is recommended that only the Master User has access to the programming functions Get operation of the system and to the Main Alarm Host Zones The system could monitor 31 wireless zones supporting up to 124 wireless accessori
25. ice message for one more time Press the Main Alarm Host will end the call and stop dialing the next auto dialer number The system will return to Armed mode Directly hang off the phone the Main Alarm Host will end the call and automatically dial the next auto dialer number Programming Main Alarm Host Your G70 is configured to provide a basic functional alarm system but the ready to use alarm system will still need a few settings and adjustments Entering The Program Mode Access to the Program Mode menu on the Main Alarm Host is protected by a User Code default is 888888 Program Mode Main Menu To enter the program mode oe SES Set Date CutWire Alarm fy SET Enter User Code ENT Auto Dialer s Zone Attribute Entry Delay Set Smart Zone h A or Y button to choose from the following Exit Delay Program Sensor Siren On Off Wireless Code NOTE It is strongly recommended that Arm Disarm Beep Alarm History only the Master User has access to the o S A User ID Status History MN programming functions Get operation of the system and to the Main Alarm Host Time Date Settings Set the time and date displayed on the Main Alarm Host Set Time In program mode when Set Time is displayed b ENT Wd Use button to delete the old record then input HHMMSS ENT HHMMSS 6 digit meaning hour HH minute MM second SS each takes 2 digits space For example 14 21 20 you may press 142120
26. ing a Wireless Door Sensor the following should be considered e You are recommended to have your front and back doors fitted with a Wireless Door Sensor Depended on your security requirement fit additional door sensors to other vulnerable doors windows if required e Ensure the Wireless Door Sensor is within effective range of the Main Alarm Host Installing The Wireless Door Sensor 1 Remove the battery cover at the left side of the sensor 2 Slide the battery supplied into the battery holder with facing upward 3 Refit the battery cover and mount the unit using the double sided adhesive pads MN NOTE Ensure the mounting surfaces are clean and dry before mounting Internal Siren Overview And Hints The Internal Siren acts as a wireless spot alarm which receives alarm signal from the Main Alarm Host The siren has a power plug and produces both sound and flash alarm when triggered When using an Internal Siren the following should be considered e It is recommended to have the Internal Siren at a height above 1 8 meters Installing The Internal Siren 1 Plug the Internal Siren into a suitable indoor mains socket at a height above 1 8 meters Smoke Detector Overview And Hints The Smoke Detector is designed to monitor smoke caused by fire The Smoke Detector is activated 24 hour to protected the area and will trigger an alarm upon detection of a smoke Installing The Smoke Detector 1 Use the mounting bracke
27. larm immediately By Main Alarm Host Wireless Remote Keypad bh the Main Alarm Host will alarm immediately System Disarming And Stopping An Alarm In any case a triggered alarm could be stopped by disarming the system To disarm the system using the Wireless Remote k amp the Main Alarm Host will beep twice to exit from any Armed mode To disarm the system using the Main Alarm Host Wireless Remote Keypad h ESC Password ENT The Main Alarm Host will beep twice to successfully complete the operation NOTE The default user password for the Main Alarm Host and the Wireless Remote Keypad are 888888 and 111111 respectively To disarm the system remotely by Phone Call the phone number associated to the system you will hear one bi sound after connecting to the system Within 30 seconds after connection enter the user password default is 888888 of the Main Alarm Host Enter O after another bi sound the Main Alarm Host will automatically hang up after the bi sound to complete the operation To disarm the system remotely by SMS Send the SMS message XXXXXXCF from your mobile phone to the Main Alarm Host XXXXXX is the 6 digit user password default is 888888 on the Main Alarm Host The Main Alarm Host will disarm the system automatically upon receiving this SMS and reply with a message System Disarmed when the system is successfully disarmed NOTE If you input the code 3 times incorr
28. n result in the risk of fire or electric shock Your Quick Guide To G70 System Installations NOTE Before proceeding to install your G70 Alarm System it is important to study your security requirements and plan your installation For useful installation hints please refer to the Installation section Main Alarm Host And Wireless Remote Keypad Area One Armed 1 Screw the antenna by hand onto the Main Alarm LZ Host until firmly attached Een A E 2 Carefully insert a valid GSM SIM card into the SIM AAA SET Card Slot located at the rear of the Main Alarm Host ae NS ENT 3 Apply AC DC power to the system with the power adapter provided 4 Turn on the battery switch located beside the power connector 5 Position the Alarm Host Anchor Guidance on the desired mounting surface NOTE When selecting mounting location avoid fixing any unit onto or very close to metalwork i e radiators water pipes etc as this could affect the radio range of the device 6 Drill two holes insert wall anchors and fasten with the two screws al 7 Position the Main Alarm Host onto the wall 8 To install the Wireless Remote Keypad repeat Steps 3 7 Your Quick Guide to Alarm System Installations Cont Wireless Wide Angle PIR Sensor ioe e D 1 Use the mounting bracket to mark two drilling J gt Y holes in the corner of a room mounted at a a AA height of between 2 and 2
29. or Front Door Back Door Patio Doors Vulnerable Doors Windows Access Doors To Important Rooms Wide Angle PIR Sensor Hallway Covering The Main Living Room study Bedrooms Main Alarm Host Or Access Route Between Landing Wireless Control Keypad Bedrooms Smoke Detector Kitchen Ceiling Living Room Ceiling and Important Areas Aisles NOTE It is important to examine whether the selected sensor locations will cover all your security requirements If necessary make any sensors rearrangement and or purchase additional sensors for additional protection Main Alarm Host And Wireless Remote Keypad LCD Display System Status Icon UP GSM Signal Smart touchpad DOWN GSM Signal Program mode Home Away oe A CH Este TT sg Confirm key Your G70 is controlled by a Main Alarm Host designed to collect data from various sensors within the protected site Wireless Remote Keypad is designed to interact with the Main Alarm Host and to use for daily operations The system is capable of monitoring up to 39 zone and has an auto learn sensor function for easy addition of remotes detectors and sensors You should consider the following before proceeding to installation e Preferably using the Wireless Remote Keypad for your daily operations and keep the Main Alarm Host in a safe location within reach of a mains socket and out of sight of potential intruders e Mount the Wireless Remote Keypad at a convenient location an
30. pad In standby mode O Password ENT A or Y button to choose Armed Home or Armed Away ENT NOTE The default user password for the Main Alarm Host and the Wireless Remote Keypad are 888888 and 111111 respectively n Armed Away mode all sensors can trigger the alarm when system is armed In Armed Home mode only the sensors set in the Perimeter zone can trigger the alarm when system is armed To arm the system remotely by Phone Call the phone number associated to the system you will hear one bi sound after connecting to the system Within 30 seconds after connection enter the user password default is 888888 of the Main Alarm Host Enter 1 after another bi sound the Main Alarm Host will automatically hang up after the bi sound to complete the operation MN NOTE Arm by phone only has Armed Away option To arm the system remotely by SMS Send the SMS message XXXXXXBF from your mobile phone to the Main Alarm Host XXXXXX is the 6 digit user password default is 888888 on the Main Alarm Host The Main Alarm Host will arm the system automatically upon receiving this SMS and reply with a message System Armed when the system is successfully armed Initiating An Emergency Alarm An emergency alarm is triggered upon pressing the button on the Wireless Remote or on the Main Alarm Host Wireless Remote Keypad By Wireless Remote lr the Main Alarm Host will a
31. pload Status is displayed b ENT Use A or Y button to select YES to enable this function Default is NO ENT Cut Wire Alarm Model G70 GT and G70 GTW Only This option is to set the alarm if the telephone land line is being cut off In program mode when CutWire Alarm is displayed b ENT Use A or Y button to select YES to enable this function Default is NO ENT Zone Attribute The system is managed by allocating the accessories into Zone Number Zone Type Alarm Type Bypass Zone and Entry Delay Set Below shows the default zone allocation and recommended sensors user has the flexibility to assign their own configuration if necessary Zone 00 01 31 38 are fixed zones om Jejeje olor l lolo ee eee ee Zone Type Emergency Perimeter am yoe renos Tele o Jo o or 9 wo o ololo ala Wireless Door l Wireless Wide Other Recommended Remote Wireless Infra Red Gas Smoke Magnet amp Curtain Angle PIR Wireless Accessories Beam Detector PIR Motion Sensor Sensor nemoe 0 opa EE a 2 00 oo oo os oo ca co Jos l Wired Door l Recommended Other Wireless Wireless Wide Angle PIR Other Wireless M ES Wired Smoke agne Accessories Sensor Motion Sensor Sensor Sensor Curtain PIR Sensor Zone Number The system has 39 zones in total 29 wireless zones each zone supports up to 4 sensors 8 wired zones optional and 2 dedicated zones for
32. r the sensor door window is currently opened or closed b A or Y button to select OP or CL on the menu ENT Choose OP let the Main Alarm Host knows the sensor door window is currently opened Choose CL let the Main Alarm Host knows the sensor door window is currently closed Default is CL for all zones Door Chime Function Finally you have the option to enable or disable a sound indicator Chime Function when a sensor in this zone is being triggered in the standby mode b A or Y button to select YES or NO in the Zone Indicator menu ENT Choose YES then the Main Alarm Host will provide a few bi sound to indicate a sensor in this zone is being triggered in the standby mode Choose NO if you do not want a sound indication when a sensor in this zone is being triggered in the standby mode Chime function works for both the normal and smart sensors Program Sensors This setting is for adding changing or deleting sensors in all zones including Zone Number 00 01 To activate a sensor in Program mode when Program Sensor is displayed fy ENT d Use button to delete old Zone Number then set XX ENT XX 2 digit for valid operation you can set a Zone Number between 00 38 See Zone Attribute for more details As each zone can accompany up to 4 sensors defined as 0 1 2 or 3 A Group Number must be selected fy ENT d Use button to delet
33. ries easily and simply including Wireless LCD Remote Keypad Wireless Motion Sensor with motion triggered recording required optional sensor VS DVR etc produced by Unifore Security Additionally optional Wireless CCTV Systems and IP Camera are available for user to increase the security level By adding a Smart Door Sensor VS PWMC the system could be configured to notify the user a door or window is still opened upon arming User has the option to force arming the system with the smart zone unprotected or to close the opened door or window prior to full arming Installation It is strongly recommended to plan your security arrangement prior to the installation of your G70D Security System For your convenient ALL accessories delivered with your G70D system will be registered to the Main Alarm Host to provide a basic functional system User has the flexibility to assign their own configuration if necessary Zones 00 01 31 38 are fixed zones To program the system please refer to Program Sensors section The table provided in Appendix A at the end of this manual will assist you to register your owned settings such as the intended location of each detector the holder and assignment of each transmitter Please refer to Your Quick Guide To G70D System Installations for picture instructions Below is the suggested installation locations for different units use it as a guide for planning your alarm system Door Sens
34. rvice life of the battery is approximately 1 year To ensure normal operations of the system replace with new batteries whenever you feel a sensor is not detecting properly Common Problems and Solutions The alarm host goes off immediately The telephone incoming line has after connected to the power not been connected or not well Connect the telephone incoming line well connected The alarm host can t record playback The record button is not pressed 1 Press the record button while recording maximum message correctly message length is 10 seconds Repeatedly receiving the alarm Fail to operate according to Follow the instructions after answering the alarm telephone the operation instruction of the phone calls and hearing the recorded message See telephone alarm Recording Playing A Message And Sound Control The host does not alarm after the 1 Caused by the functions of arm 1 Armed Away mode the alarm goes off when any detector is triggered in arm state mode Armed Away and Armed sensor is triggered Home 2 Armed Home mode the alarm goes off when any 2 Have already setup time for sensor in perimeter zone is triggered and it won t alarm Entry Delay or Exit Delay when any sensor in motion zone is triggered 3 Program to adjust the time for Entry Delay or Exit Delay The PIR sensor doesn t work 1 Not connected to the power 1 Open the sensor shells to install the battery and turn 2 Low battery on power switch
35. t method Call By Phone SMS Reporting ENT Repeat steps for 2nd phone number 3rd phone number etc In total you can program up to 5 phone numbers NOTE Users could set a private number to the 1st telephone number Call Center Number if they are monitoring the system themselves Entry Exit Delay To set the entry or exit delay time of alarm this option allows you to disarm or arm the system in a limit time NOTE Only available for sensors set to Perimeter and Motion zones See MN Zone Attribute section below for setting zone arrangement Entry Delay In program mode when Entry Delay is displayed b ENT Idi Use button to delete the old record then input set XX ENT XX 2 digit you can set an entry time delay between 00 59 seconds default is 00 S shown at the bottom left of the screen indicates the value is in second Exit Delay In program mode when Exit Delay is displayed b ENT Idi Use button to delete the old record then input set XX ENT XX 2 digit you can set an exit time delay between 00 59 seconds default is 15 Turn Siren On Off This option allows you setting the siren to alarm or mute when sensors are triggered For your options the system has independent setting for the 3 zones Perimeter Motion and Emergency zones See Zone Attribute section below for setting zone arrangement In program mode when Siren On Off is displayed ENT WM Use b
36. t to mark two drilling holes on the wall Drill the holes and fit two screw provided to fix the bracket 2 Remove the battery cover and connect the provided battery to the battery clip 3 Refit the battery cover Slide in the detector and rotate clockwise to lock the detector onto the mounting bracket NOTE Do not drill the fixing holes with the bracket in position The power tool may cause damages to the bracket Factory Settings Main Alarm Host Master Code 888888 e Wireless Code 00001 e Auto Dialer s Not programmed e Entry Delay OFF 0 second e Exit Delay ON 15 seconds Alarm Time Emergency ON 1 minute Perimeter ON 1 minute Motion ON 1 minute s Arm Disarm Beep ON User ID e Upload Status NO e Zone Attribute See Zone Attribute for the default zone allocation and recommended sensors Wireless Remote Keypad e Master Code 888888 e User Code 111111 e Wireless Code 11111111 Securing The Protected Site Security Related Buttons Main Alarm Host Arming the system both for ap and Home Arming Jeroen Arming remotely when nobody Is at home Disarming remotely when nobody is at home Password BF Arming remotely when nobody is at home Password CF Disarming remotely when nobody is at home System Arming k To arm the system using the Wireless Remote h L4 button for the Armed Home mode To arm the system using the Main Alarm Host Wireless Remote Key
37. tact the programmed telephone numbers in the system Upon receiving the call the recorded voice message is played immediately for 30 seconds repeatedly User has the following options Press 8 to enter into the listening status and hear the alarm background sounds for 20 seconds Press to play the recorded voice message again Press the Main Alarm Host will end the call and stop dialing the next Auto Dialer Number The system will return to Arm status Directly hang off the phone the Main Alarm Host will end the call and automatically dial the next Auto Dialer Number Door Chime Function By allocating a sensor to the Chime zone whenever a sensor in that zone is triggered in the standby mode the system will produce a few bi sound to alert the user Please refer to Set Smart Zone for more details Introduction Overview G7O0D series wireless GSM LCD touchpad alarm system is the state of the art LCD touchpad wired wireless alarm system for home and office security Its aesthetic design with a user friendly illuminated LCD menu and a touchpad control provides a new standard of security alarm system and makes your home works in a Hi Tech style You can install the system and monitor your home office all by yourself or via a security center service with Ademco CID protocol G70D secures your property for you while you enjoy your life NOTE This manual is designed to familiarize you with t
38. utton to delete the old record in Emergency zone then set the alarming duration time minutes XX ENT Repeat step for Perimeter and Motion zones XX 2 digit you can set a siren time between 00 60 minutes defaults are 01 1 minute for Emergency Perimeter and Motion zones M shown at the bottom left of the screen indicates the value is in minute NOTE If the time is set to M 00 for a particular zone then the siren will be set to mute mode for this zone Arm Disarm Beep This option allows you to choose whether to have a short siren sound when arming or disarming the Main Alarm Host In program mode when Arm Disarm Beep is displayed bh ENT Use A or Y button to select YES or NO Default is YES ENT User ID This is used to identify the system number for a security call center Individual user can ignore this setting In program mode when User ID is displayed k ENT Idi Use button to delete any old record then set XXXX ENT XXXX is the User ID you can set to a 4 digit number between 0000 and 9999 Default user code 0001 Upload Status This is used when you want the system status such as Arm Disarm Alarm and AC power failure to be reported to the Call Center number If you are monitoring the system by yourself this function will report any status changes in the system by SMS message to the Call Center number which is set to your mobile number In program mode when U
39. y Useful Hints For Users Stopping An Alarm 3 A triggered alarm can be stopped by 5 Password on the Main Alarm Host default 888888 or Wireless Remote Keypad default 111111 or by using the Wireless Remote To stop an alarm remotely press the button after receiving the call from your system the system will remain Armed and the next number will not be called By SMS message send a message XXXXXXCF to the Main Alarm Host XXXXXX is your 6 digit User Code on the Main Alarm Host The system will be Disarmed and a confirming message will be sent Emergency Perimeter and Motion Zones sensors set to the Emergency zone will trigger an alarm in Armed Disarmed mode upon disturbance Sensors linked to the Perimeter zone can only trigger an alarm when the system is in Armed mode Home Away Sensors programmed to the Motion zone could only trigger an alarm in Armed Away mode System Testing With the system in standby mode user could trigger each sensor or accessory one by one The triggered unit will be shown on the Main Alarm Host without triggering an alarm SMS Reporting By programming a private number to be the 1st caller number Call Center Number and if the upload status has been enabled you will be able to receive system information such as Arm Disarm Alarm or AC failure Telephone Alarm lf an alarm was triggered and providing a valid GSM SIM card is present the system will automatically con
Download Pdf Manuals
Related Search