Dowanload User Manual
Contents
1. SERVER 1 www cooaccess net 8841 0 It will reply OK after set successfully 5 4 Set the center number If you want to cut off restore oil by SMS command you have to set a center number firstly Only the center number can send the cut off restore oil command to the device You can set your own mobile number as center number The command for setting center number is CENTER A mobile number For example Concox Track amp Achieve CENTER A 18165542976 If set successfully there isan OK reply message Only the SOS number can be used to add or delete center number successfully There is only one center number can be set 5 5 GPRS time interval Users can modify GPRS time sending interval by SMS TIMER T1 T2 T1 ranges 5 18000 or O seconds upload interval when ACC ON 0 means no upload default is 10 T2 ranges 5 18000 or O seconds upload interval when ACC OFF 0 means no upload default is 10 5 6 Vibration alarm delay time setting Delay time for device entering vibration alarm state after the vehicle power is off and ACC is in low level In the vibration alarm state if the vehicle vibrates for a few times it will activate the vibration alarm system If the vehicle battery is still not on ACC is in low level after 3 minutes the device will start vibration alarm SMS format DEFENSE TIME The time ranges from 1 to 60 minutes default is 10 Note Concox Track amp Achi2. metal compound of the case 3 The device should be fixed into position with cable ties or wide double side tape Installation please refers to below picture Concox Track amp Achieve 1 Best place to install P Inside the Under the back seat NE cover Inside the ao re i Xl speedometer taillight cover SNNN lt NE or the plastic POR S I component SAC i lo d Under the dash board below the front windshield In the parcel shelf in the rear In the front bumper non material face make sure the device does not get wet Under the wiper version non metal make sure the device does not get wet Non Covert Installation fix the device on the dash board below windshield Device Wiring 1 The standard voltage is 9V 90V the red wire is the positive the black wire is the negative 2 Connect the black wire to ground 4 5 Device wiring diagram Concox Track amp Achieve Relay a 30 Bfa 85 NOTE Please pay attention to the diagram description battery is 9 90V and relay remains 12V 24V 4 6 Power ACC Tele cutoff petrol electricity control line 4 pin 1 Your device comes with a power cord and Is designed to use only manufacturer specified original device The red line is positive while the black one is negative the side should not be connected with ground wire Concox Track amp Achieve 2 The ACC line orange connects to ACC switch of the vehicle Please be sure to c
3. Concox Track amp Achieve General GPS Vehicle Tracker User Manual V1 0 Concox Track amp Achieve Introducing your Device Learn about your device s layout indications and specifications 1 Inside the Box Check your product box for the following items gt Device gt Charging cable gt Relay gt User Manual 2 Overview GSM LED indicator Power status GPS LED indicator Power connector Power indicator red Quick Flashing flash 0 3s at interval of 0 3s Solid red Charging Flashing flash 1s at interval of 3s Full charge Concox Track amp Achieve O Power off or low battery Slow flashing flash 0 1s at interval of 3s Working normally GPS indicator blue Indication GSM initializing Receive GSM signal normally In communication with phones No GSM signal or no SIM card Slow flashing flash 0 1s at interval of 3s GPRS on line 270mAh 37V 850 900 1800 1900 MHz Class 12 TCP IP Concox Track amp Achieve Acquisition Sensitivity Data Transmit TCP SMS Geo fence Alarm Alarm when get in or get out a specified area Speeding Alarm Report when speeds higher than the pre set value Low Power Alarm Alarm when backup battery is running out Non movement Movement alarm based on built in 3D motion Detection sensor Mileage Report Track by time distance interval Remote Control Cut off petrol electricity 4 Getting Started 4 1 Switch on Get started by
4. assembling and setting up your device for its first use 1 0pen the SIM card cover Concox Track amp Achieve 2 Insert the SIM card S mii jill HID TULD j H Note SIM card should be equipped with GPRS and SMS functions 3 Turn power on Ww 4 Close the SIM card cover and connect the device with the external power line which will be used to charge the terminal and built in battery Concox Track amp Achieve 4 2 Switch off 1 Take the SIM card out and turn power off 4 3 Charge the device Covert installation Plug the device connector into a charging cable The charging cable with 2A FUSE for short circuit over current protection Concox Track amp Achieve NY f N Note Improperly connecting the charging cable can cause serious damage to the device Any damages by misuse are not covered by the warranty 4 4 Install the device You need to choose somewhere that it won t be found because the whole point of fitting covert GPS vehicle tracker is the secrecy element 1 Your device has built in GSM antenna and GPS antenna During installation please make sure the receiving side face is up any high power devices such as reversing radar anti theft device or communication equipment would affect the signal of the device 2 All metallic cases of the windshield will attenuate the signal on the tracking device It s simply due to the shielding effects of the
5. e device The format iski J After receiving this command the device will reboot after 1mins 7 Register and log onto GPS tracking platform www cootrack net Account IMEI Number The function on the GPS platform can be realized as follows gt Real time Tracking gt Report and Statistics gt Online Configuration 8 Troubleshooting If you are having trouble with your device try these troubleshooting procedures before contacting a service professional Red LED does The fuse blows Replace the fuse Concox Track amp Achieve not work when power connected l Check SIM card installation Wrong installation of SIM iia mw card P1 1 Install SIM card Filth on the SIM card iron Clean it surface M Contact internet service Fail to connect Useless gt provider network nstallati Check installation of device mproper installation prop P43 Install the device l Use it in effective GSM Beyond GSM service area service offer area Try again in a better signal Bad signal area Connect with power with The voltage is unsuitable Fail to suitable voltage charge Check connection with Improper connection charger ShenZhen Concox Information Technology CO Ltd Tel 86 755 2912 1200 Fax 86 755 2912 1290 E mail jason concox cn Add 4 F Building B Gaoxinqi Industrial Park Liuxian 1st Road No 67 Bao an District Shenzhen www iconcox com
6. eve 1 Preset SOS numbers before sending SMS alarm messages and calls 2 If there is no need for vibration alarm please SMS Say FANE Relgziato close it 5 7 Check parameter setting You can check the parameter setting by command PARAM Example Wawa E Information replied IMEI 353419032348877 IMEI number of the device TIMER 10 10 GPS data uploading Interval SENDS 5 the GPS working time when ACC is OFF SOS 18165542976 SOS numbers maximum 3 SOS numbers can be set and used for alarm and monitoring Center Number 18165542976 only 1 center number can be set and used for cutting off restoring oil command Sensoralm 10 5 1 180 detect 5 vibrations in 10s the alarm delay is 180s Defense time 10 the vibration alarm delay is 10 minutes TimeZone E 8 0 time zone info The replied information contains IMEI number GPS data uploading Interval GPS working time SOS number center number sensor time interval vibration alarm delay and time zone info 5 8 Check GPRS parameters Concox Track amp Achieve SMS command format GPRSSET Example Cla SS E Reply message GPRS ON GPRS on off status Currently use APN CMNET user password APN setting information SERVER 1 www cooaccess net 8841 0 platform information URL http maps google com maps q preset web link setting information 6 Operation of device 6 1 Power on Power off Powe
7. larm In this case the device will send related SMS to the specific numbers and dial the numbers in circles If nobody answers the call just keeps 3 loops at most At the meantime the device will upload SOS alarm data to the server And it will send Concox Track amp Achieve Cut Power lt Date Time 13 06 17 14 53 06 gt http maps google com maps q N225 76713 E113 916585 Note The specific numbers should be preset please refer to 5 1 6 4 Low battery alarm When the device is only working with battery once the internal voltage of battery is less than 3 7V device will send low battery alarm SMS to specific number and alarm on platform Low battery alarm SMS content example Attention Battery is too low please charge Which means the battery is too low inform user charging it in time Note The specific numbers should be preset please refer to 5 1 6 5 Vibration alarm The vibration alarm function is off by default To activate this function please send the following command SENALM ON The alarm will be sent to both the service platform and SOS numbers When vehicle power is off ACC status is low and if the lead time of low ACC is more than 10 minutes settable device will activate security alarm When the security alarm is on once the vehicle vibrates for several times the alarm will be activated in the next 3 minutes if vehicle power is still off ACC status is low device will start alarm At this
8. onnect the ACC line otherwise the device will enter ignition detection status when disconnect the ACC line If you don t need to anti theft temporarily just connect the ACC line to the positive side in parallel 3 Tele cutoff petrol electricity control line yellow is connected to pin 86 of the Tele cutoff petrol electricity relay equal to the yellow line of the relay socket 5 Quick Operation Instructions To properly use the device common parameters should be set before initial use This can be done by using the parameter editor or by sending SMS commands to the device should be English comma and no space before and after the comma 5 1 Add SOS number SMS command to the device to add the SOS number SOS A No 1 No 2 No 3 A means to add new numbers for example SOS A 18165542975 18165542976 18165542977 It will reply OK SOS1 18165542975 SOS2 18165542976 SOS3 18165542977 Concox Track amp Achieve after set successfully 5 2 APN setting To connect default platform www cootrack net please send the SMS command below APN command format APN APN name feJgAPN APN name user name password Example APN CLENTE fe g APN ORANGE ORANGE ORANGE An automatic reply OK will be sent in one minute if setup is successful 5 3 Server setting To connect other platform please send the SMS commands below Command format SERVER 1 domain Port 0 Example
9. r on Once insert a valid SIM card and connect all the wires turn on the device then Power LED will flash first during signal searching process GSM and GPS LED will flash Once GPS LED keeps slow flashing it means the device has been located and it starts to work Power off Just turn off the power switch The device will begin to upload positioning data to server once inserting a valid SIM card and power on During the working time it can upload data to server every 10 seconds Note To power on power off please remove the back cover first refer to 4 Getting Started Concox Track amp Achieve 6 2 Check location 1 Via SMS 1 1 SMS WHERE A the SIM number of device The device will send a location message automatically You can get the coordinates If the device does not search any information of location it willsend No data to the cell phone Example Current position Lat N22 577156 Lon E113 916748 Course 131 99 Speed 0 00Km h Date Time 2013 10 08 17 35 32 1 2 SMS to the SIM number of device The device will send a location Google Map link If the device does not search any information of location it will send No data to the cell phone Example lt 10 08 17 36 gt http maps google com maps q N22 577156 E113 916748 2 Via platform Go to the platform website offered by dealers to check your vehicle location 6 3 Wire cut off alarm When the electricity supply of device is cut off it will activate cut off a
10. this command is valid only under two conditions the GPS is located the speed is less than 20km h 6 7 Restoring Oil 1 Via platform When the alarm is off sending recover oil commands manually Device will restore oil supplying and vehicle will work normally again Platform account password is needed when sending oil cut off command 2 Via SMS Only center number can send the command to the device to restore oil The format is After the command is carried out it will receive Restore fuel supply Success 6 8 Over Speed Alarm When the car is moving over a limited speed in average in a limited time period then the device will send over speed alarm SMS to user To turn on the over speed function please send below SMS command SPEED ON Time Limited speed way of alarm Time range Second 5 600s default as 20s Limited speed range km h 1 255 default 120 Concox Track amp Achieve Way of alarm 0 GPRS only 1 SMS GPRS default 1 Means when the car is moving over 120km h in average in 10 seconds the device will send over speed alarm to user 6 9 Restore to factory setting SMS command format to set all parameter to default factory value Once received OK it succeeds 6 10 Reboot device When there is something wrong with the link of GPRS e g the parameter setting of the device is correct but you can t track the car on the platform At this moment you can send a command to the device to reboot th
11. time it will send alarm message to the service platform with the latitude and longitude while the platform will reply the Chinese address Then the Concox Track amp Achieve terminal will send vibration alarm message to SOS numbers with the Chinese address and call the SOS numbers in cycle If nobody answers it will stop calling after 3 loops If the Chinese address can not be acquired for certain reason the terminal will send a message with the website link to the SOS numbers Example Sensor Alarm lt 11 23 14 53 gt http maps google com maps q N22576713 E113 916585 Note 1 The SOS numbers should be preset 2 Send SENALM OFF to turn off the vibration alarm if don t need 6 6 Oil cut off 1 via platform Send oil cut off command on platform To make sure the security of vehicle tracker can only indicate to cut off oil when GPS is in valid position status and the speed is less than 20KM H or in static Platform account password is needed when sending oil cut off command 2 Via SMS Firstly you should set a center number Please refer to 5 4 Only center number can send the command to the device to cut off and restore oil The format is Ya F YA E Concox Track amp Achieve After the command is carried out it will reply Cut off the fuel supply Success Speed 0 Km h If the command didn t carry out it will reply the reason about fail to carry out Note To ensure the safety of the driver and the car
Download Pdf Manuals
Related Search