Universal Reel-to
Contents
1. counter will reset the count and restart the RRC 300 U A FOR YOUR SAFETY Switch off device before any manipulation OPERATION The RRC 300 U uses a state of the art ultrasonic fork detector that allows the RRC 300 U to count almost any type of labels including transparent labels The ultrasonic detector detects the labels by sensing the difference in thickness between the backing paper and the backing paper plus label The gap between two successive labels should at least of 2 millimetres mm The label should of minimum 5mm height the maximum width is 152mm The detector has been adjusted at the factory but may need to be re adjusted slightly for your labels The procedure for calibrating the detector is described in the enclosed sensor user manual The detector is normally set for dark switching A WARNING This Product is for indoor use only Not for use in wet locations IMPORTANT It is recommended to use the machine at its maximum speed Keep unwind plate clean of particles and glue LEFT SIDE CONTROL PANEL RESET The new left side control panel has three items The toggle switch reset is a momentary closing switch that has the same function as the reset button on the counter but is more convenient for the operator ADJUST Potentiometer TEST Green LED O ADJUSTING THE LABEL DETECTOR PHOTOCELL The label detector photocell has been adjusted at the factory potentiometer fully CCW and requ2. MAINTENANCE Your RRC 330 U requires no maintenance but to keep the unwind plate clean Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders ae cal Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributo
3. e This product is a reel to reel label counter It is only to be used to count rewind unwind labels of the recommended dimensions and weight in an indoor dry environment e The machine has to be unplugged before any manipulation The machine is to be used on a flat surface if the surface is not flat it is to be fixed using the holes in the base plate Do not leave the power cable in a passageway The ambient light of the working area needs to be sufficient to avoid any risk The dispenser can be used in ambient temperatures of 2 C to 40 C All measures have been taken to minimise risks of injuries with the take up shaft but the operator has to be careful when manipulating the bail e Connection of the machine to the power source must respect local and European legislations SET UP 1 Plug the Power Cord into a suitable AC Power Mains Outlet and to the power input jack on the rear panel Place the Power Switch on the rear of the RRC 300 U to the ON 1 position Observe that numbers are displayed on the Counter See the separate User Manual for the Counter Modules itself for other operations 2 The Counter is pre programmed as a Preset Count Up Counter If you want to use the preset function introduce the number of labels with the blue push button on the counter If you do not want to use preset set the value to 0 3 When the preset number of labels is reached the RRC 300 U will stop Pressing R on the
4. ires no adjustment for a large variety of labels However some specific labels very transparent or relatively opaque backing paper might require adjustment of the photocell Load a roll of labels on the machine and position the backing paper in front of the photocell Make sure that the labels are tensioned when doing the test The LED should light on If not rotate the potentiometer till LED goes on green Now put a label in front of the photocell the LED should turn off
5. r you bought the product from The customer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_RRC U CE 06 15 Original user manual RRC 330 U Universal Reel to Reel Counter e Variable Speed Control e 6 Digit Digital Pre set Counter e 300mm 12 Roll Diameter Remove all parts from the shipping container and verify contents PACKAGE CONTENTS e User Manual this document e Sensor User Manual e RRC 300 U Unit e Power Cord e Separate User Manual for Counter Unit Retain the Shipping Container and Packaging for Storage and Transport SPECIFICATIONS Weight of the machine STD 12Kg ACH 12 5Kg Max Label Roll Weight 7Kg Max Label Roll Diam 330mm Power Supply Input 220 240VAC 50 60Hz Speed Max 72cm sec with 76mm take up roll diameter at beginning of the roll Max 235cm sec at end of 300mm roll e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e IMPORTANT INFORMATION
Download Pdf Manuals
Related Search