Home

Pace DTR5520 - User Guide

1. Mains wall Socket m C Connect the aerial cable not supplied from the aerial wall socket to the Antenna IN connector on the rear panel of your HD receiver Use the supplied HDMI cable to connect the HDMI connector on the rear panel of your HD receiver to the HDMI input connector of your TV For the next step note the chosen HDMI input of your TV e g HDMI 1 Connect your TV to the mains and select the correct A V source on your TV This should correspond to the HDMI input connector to which your HD receiver is connected If necessary refer to your TV s user manual for instructions Notes Optionally you can also use the supplied RF cable to connect the RF output connector labelled To TV VCR of your HD receiver to the RF input connector of your T V connect your HD receiver to your standard definition TV see page 29 10 3 3 Installing your HD receiver Before you start the installation make sure you have made all the required connections Kl Connect the 12V power supply unit to the 12V input connector on the rear panel of your HD receiver Connect the mains plug to the mains wall socket Ensure that the ON OFF switch on the rear panel of your HD receiver is switched on is in the 1 position Your HD receiver displays a welcome m
2. change channel up or down 4 Res button To change the HDMI output resolution to Auto default 576i 576p 1080i or 1080p 5 V Out button To change the active video output to HDMI default or SCART 6 Display 4 digit display 7 HD indicator Lights up when you are watching an HD channel 18 Rear panel 1 Antenna IN To connect your aerial cable from the wall socket 2 To TV VCR Antenna output to TV VCR antenna signal 3 Ethernet To connect your HD receiver to an Internet access point 4 USB 2 0 Universal Serial Bus port 5 HDMI To connect to the HDMI input connector on your high definition TV 6 AUX SCART To connect to the SCART connector on your standard definition TV or any recording device such as aVCR 7 DIGITAL audio out To connect an hi fi amplifier 8 AUDIO L R To an hi fi amplifier 9 ON OFF switch To switch on off your HD receiver 10 connect the 12V power supply unit Safe extra low voltage Using more of your HD receiver 5 2 Remote control TD lobe GUIDE OPTIONS PHILIPS DIGITAL RECEIVER Using more of your HD receiver AW N A 11 1 2 MENU RADIO 4 EXIT 5 Colour buttons 6 7 AVP 8 9 10 Number buttons 11 amp J 12 AD 13 VOL 14 15 i 16 OK 17 18 TEXT 19 ED Switch to standby or wake up from standby Open close Main menu Switch between radio and TV channels Remove me
3. Connecting your standard definition TV 1 Aerial wall socket HD receiver w r Mains wall socket Connect the aerial cable not supplied from the aerial wall socket to the Antenna IN connector on the rear panel of your HD receiver Use a SCART cable not supplied to connect the AUX connector on the rear panel of your HD receiver to the SCART input connector of your standard definition TV Connect your TV to the mains Use your TV s remote control to select the SCART input connector which is connected to your HD receiver as the the A V source If necessary refer to your TV s user manual Connect your HD receiver to the mains and wait until your HD receiver wakes up InSt appears on the front panel display Press the V Out button on the front panel twice AU now appears on the front panel display and the Welcome screen appears on your TV See section 3 3 Installing your HD receiver on page 10 for instructions on completing the first installation setup from step 3 Note Optionally you can also use the supplied RF cable to connect the RF output connector labelled To TV VCR of your HD receiver to the RF input connector of your T V 29 v2 j UO Z Guarantee and service For the Philips warranty applicable to your HD receiver please visit the Philips website www philips com guarantee In case you do not have an Intern
4. To put your HD receiver into standby press on your HD receiver s front panel or remote control To take your HD receiver out of standby press 9 again You can also press BACK or any number button on your remote control to wake up your HD receiver See page 6 for more information 4 2 Switching on and off Use the ON OFF switch on the rear panel of your HD receiver to switch your HD receiver on off See page 6 for more information 4 3 Changing channels To change channels use the on your remote control or your HD receiver s front panel You can also use the number buttons your remote control Press BACK to switch to the last channel you were watching You can also use the on screen channel lists or channel banner to change channels see sections 4 5 and 4 6 Note Initially HD programmes are available only on channels 50 and 51 Switch to these channels to watch HD programmes 4 4 Adjusting volume To increase or decrease the volume press VOL VOL The volume level is shown briefly on your TV To mute or restore the sound press UK When you mute your sound the icon is shown in the top right corner of your TV This icon disappears after a few seconds Using your HD receiver 4 5 Using the channel banner Channel information When you change a channel the channel banner appears briefly to show information about the current programme By default it appears for 5 second
5. mE Chiral mode Parental control l To schedule a new recording make sure New timer is highlighted and press or OK The New manual recording menu appears Using your HD receiver Note If parental control is on while scheduling a recording on a locked channel we recommend you to go to the Parental control menu and enter your PIN code then reported as Typed In that case the recording will start automatically HD set top box TV quide amp scheduling Scheduled recordings Hew recording Date 2004 Start time teat Ered thine 15 37 BBC THREE Channel Repeat mode Once Parental contra Hot typed in Cancel Contin au am Select the recording date Chaoss Confirm to schedule the recording when done Use A to highlight the setting you want to change and press gt or OK UseA V to change it and press the green button to confirm the recording timer Press the red button to cancel the recording timer and return to the Scheduled recordings menu To delete an already scheduled recording use V to highlight it and press the red button HD set top box TV guide amp scheduling Scheduled recordings Dennis How tirer Late 23 03 04 Schools See You See Me Start 10 33 HREE 12 32 THREE Repeat mode Oren Parental control Hot typed in 5 Cancel am Pd This recording is active
6. Check that all connections are properly made see page 10 e Check that your TV is plugged into the mains and that it is switched on e Check that you have selected the correct A V channel source on your TV depending on how your HD receiver is connected to it that is using HDMI or SCART Refer to your TV s user manual for instructions 22 Your HD receiver seems to be switching off automatically after some time If your receiver automatically goes into standby mode standby indicator on the front panel lights up this is due to the Eco mode The Eco mode is set to 3hours by default environmentally friendly product To modify it go to Menu gt Settings gt Preferences gt Automatic Eco mode and choose a different value See page 24 Your remote control is not working e Make sure that you point your remote control directly at your HD receiver and that nothing is between it and your HD receiver The standby indicator on your HD receiver s front panel should flash each time you press a remote control button e Check the batteries and replace them if necessary e If rEC is displayed on the front panel display everytime you press a button on your remote control see below Your HD receiver displays on the front panel display each time you press a button on your remote control and your HD receiver is locked A recording is running which locks your HD receiver To unlock your HD receiver you must STOP
7. Digital 5 1 audio output ECO power management IP address assignment Manual or DHCP Software update Update via OTA download Local update via USB Application system resources Processor STi 7105 Reception Demodulation Reception of DVB T broadcast EN 300744 Reception of DVB T2 broadcast acc D Book 6 1 Demodulation type COFDM FFT Input frequency range UHF IV V 470 862 MHz Active RF Loop through Bandwidth 47 862 MHz Switch to passive loop through in standby mode Channel bandwidth BW 8 MHz Network MEN SFN Antenna control for indoor aerial Via RF IN connector DC powering 5 Volts 50 mA Switchable via menu On Off Front panel display buttons 4x 7 segment LED display 1x bi color LED e 1x blue LED 5 x Buttons Standby P P Res V Out Rear panel connections RF in type IEC 169 2 female e RF out type IEC 169 2 male Technical data HDMI output e AUX SCART configurable by menu SCART VCR configuration for recorder Outputs 5 fixed level L R audio SCART configuration for a TV Outputs CVBS or RGB FB fixed level L R audio Slow blanking L R analogue Audio output Digital audio output Cinch electrical SPDIF DC power inlet e RJ45 USB 2 0 Master Video standard PAL Accessories Remote control Protocol RC6 Batteries 2 x 1 5V type User manual e QSG Freeview flyer Retune flyer HDMI ca
8. HD receiver lights up while watching an HD channel Digital terrestrial broadcasting is progressing in the UK As digital switch over happens the number of digital channels available in each region may also increase Please visit one of the following websites to find out when the digital switch over is scheduled for your area www digitaluk co uk www freeview co uk availability coverage checker for HD Frequently asked questions Your HD receiver seems to lock up or get stuck while retuning it to search for new channels In parts of the country where the analogue TV services have already been switched off the time taken to retune can increase This is because your HD receiver scans for all the transmitters in your area which can take up to 15 minutes Please wait for the retune to complete This is not a fault You cannot find all the channels you think should be available even after retuning your HD receiver he missing channels may not be available in your area Check your coverage on the Freeview website www freeview co uk e Your antenna may need to be upgraded signal power position orientation or cabling e A signal booster may be fitted on your antenna Consider having this removed as amplifiers are normally not required after the digital switch over Too high a signal level can cause your HD receiver to skip some channels Some early digital receivers manufactured prior to 2004 support only the 2K mode of
9. KINGDOM Phone 0800 331 60 15 Contact information 37 Trademarks and partner logos The Philips wordmark and the Philips shield are registered trademarks of Koninklijke Philips Electronics N V and are used by Pace plc under license from Koninklijke Philips Electronics N V 22 responsible Respect copyrights I DOLBY DIGITAL PLUS Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories Homi HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries Digital Video Broadcasting Trademark of the DVB Digital Video Broadcasting Project 1991 to 1996 Freeview The FREEVIEW service is subject to coverage The FREEVIEW FREEVIEW FREEVIEW HD and FREEVIEW HD words and logos are trademarks of DTV Services LTD DTV Services Ltd 2010 H The HD TV Logo is a trademark of EICTA AY A 9 100 recycled paper Pace and Pace are trademarks and or registered trademarks of Pace plc 38 Trademarks and partner logos un Z Trademarks and partner logos 39 PHILIPS 2010 Koninklijke Philips Electronics N V All rights reserved Document order number 502 1040510
10. THE RECORDING by pressing EXIT and then OK The picture is not displayed on your HDTV and an HDCP authentication error is displayed Your HDTV does not support HDCP which allows your HD receiver to transmit full resolution video to your HDTV As a result the HDMI output displays a message masking the video which asks you for changing the resolution down to 576p see page 18 Res button Frequently asked questions The picture seems to be stretched or squashed Check the TV format setting under Digital output or Analog output Main Settings gt Preferences Alternatively press the picture format button on your remote control to scroll through the different settings Also refer to your TV s user manual Your HD receiver displays err on the front panel display when you plug in a USB memory stick Reformat your USB memory stick using a computer Ensure that the filesystem is FAT16 or FAT 32 You cannot find all the channels you think should be available Retune your HD receiver see page 25 Alternatively reset your HD receiver to its factory default settings see page 26 and proceed with the first installation setup Note During the first installation your choice of the network may affect the number of installed channels You do not find any HD channels Initially HD programmes are available only on channels 50 and 51 Switch to these channels Note that the HD indicator on the front panel of your
11. Take time to read this user manual before using your HD receiver It provides important information on the installation operation and safety of your HD receiver Keep this manual next to your HD receiver for future reference Disposal of your old product Your product is designed and manufactured with high quality materials and components which can be recycled and reused When this crossed out wheeled bin symbol is attached to a product or its packaging it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection process for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste The correct disposal of your old product will help prevent potential negative consequences for the environment and human health The Material recyclability symbol affixed on the package cardboard and user manual means that these parts are recyclable So do not dispose of them with your normal household waste The Material recyclability symbol affixed on plastic packaging parts means that these parts are recyclable So do not dispose of them with your normal household waste The Green Dot symbol affixed on the cardboard means that the manufacturer of the product has financially contributed to the Avoidance and Recovery of Packaging Waste organization 4 Important 1 1 Safety inform
12. areas high buildings etc When analogue broadcasting in your region is switched off there should be a quality improvement in digital broadcasting As digital switch over happens the number of digital channels available in each region may also increase Please visit this website to find out when the digital switch over is scheduled for your area www digitaluk co uk Tl IE 72 x UO Z B On the Code entry menu use V or the number buttons to enter your area s postal code and then press OK to highlight PIN code HD zelf box Narnian Code entry Postcode PIH codo Planta Eppo i post 3 4 What if no channels are found In case your HD receiver does not find any channels check your connections see pages 10 and 29 and press the red button to start the first installation setup again Note Entering your postal code is mandatory You will not be able to complete the first installation setup without entering your postal code To change the default PIN code 0000 press gt and use the number buttons to enter you new PIN code You will then be prompted to re enter your PIN code to confirm HD zele box Narnia Code entry a M Post coc his Previo Dens Prose RIGHT ta antar our PIM cada HI zelfs box Channel search Start search Ho channel Pond Check that the antenna le correct canne tor Choose Check yu
13. digital transmissions As part of the digital switch over the UK Freeview TV platform will be upgraded to a more robust transmission standard The change transmission standard has been authorised by OFCOM and the new standard is supported by products that have the Digital Tick e If you have a SKY box switch it to standby mode and then retune the terrestrial receiver If it then receives all expected Freeview channels then the modulator needs adjusting on your Sky box Contact Sky to find out how to adjust the modulator 33 IE 72 UO Z Your HD receiver found all the expected channels after you retuned it However when you turned on your HD receiver the next day the picture was breaking up and some channels were missing Your HD receiver has an automatic retuning feature this allows it to keep up to date with minor service changes However when the signal level of nearby relay transmitters are high or if the antenna signal is being amplified these problems can occur To solve this problem e Turn off the automatic channel updates feature of your HD receiver see page 26 e Remove any signal amplifiers or boosters that are fitted on your antenna These are not required after the digital switch over e Check that your antenna is aligned properly and is a model adapted for digital signal reception in your area If you are not sure please use the services of a recognised CAI antenna installation
14. it Press OK again to watch the channel or press EXIT to remove the channel list menu without changing the channel Using your HD receiver 4 7 Using the TV guide The TV guide provides you with a listing of all programmes available on all channels for up to eight days making it easy to find the programmes you want to watch EX Press GUIDE to display the TV guide HO box TV sec xw 5 School School School School Working Lu CBRC Chann En English Hurm Word English English Look a Pri English E HDAS 24 BAC Howa BACI Money Splnmars 18 00 60 rin Ever wanted something you can t afferd Larne Spleer halpa tha mai d Corel Family save mey and realise their dream Follows By MMC Hawa ane Ate nt El Use 4 gt to see what programmes are on at different times on a channel Use A V to move through the list of channels Use the green 1 day and red 1 day buttons to move forward and backwards by a day through the listings Use the blue button to see what programmes are on from 18 00 hours onwards Use the yellow button to jump directly to the programme list for any of the next 7 days Mon 22 Mar WEEET 1530 ME Wal Hir 1 box TY guisa 10 00 10 25 an repair Mari Schaal Working Lu fish Look a Pri English E REAT Mons Laman Wed 24 Through
15. menu use A Y to highlight either TV channels or Radio channels and press gt or OK The menu now displays the default channel list All TV or All Radio and any existing favourite lists Use A Y to highlight the favourite list that you want to delete and press the green button Press 4 or BACK to return to the Favourites menu l Press 4 or BACK to return to the Favourites menu Modifying Editing favourite lists EX From the Favourites menu use A to highlight either TV channels or Radio channels and press gt or OK The menu now displays the default channel list AI TV or All Radio and any existing favourite lists Use A Y to highlight the favourite list that you want to modify and press gt or OK HD set top box Favourites TV channels 2 Ded 01 a ANIV Dad UH BEC THREE OAD HEC NEWS 24 051 RECI 0 Add Ronrave amm ove Choose Add Esemove or Move po mhi remt or DOME channel 22 5 4 2 Using the Settings menu You use the Settings menu to customise your HD receiver For example you can lock certain channels change display settings etc Accessing the Settings menu From the Main menu use A V to highlight Settings and press gt or OK The Settings menu appears HD set top box Settings messages Hetwark messages Preferences raw message avallable Parental control Set up Consul
16. or 16 9 default The options determine how widescreen 16 9 programmes show on a standard definition TV with aspect ratio of 4 3 Digital output HDMI output resolution Use this to set the HDMI video resolution to 576i 576p 720p 1080i 1080p Auto default or Original Note that you can also change this setting using the RES button on the front panel of your HD receiver 25 IE 72 x UO Z Audio capabilities on HDMI Use this to set the audio format to PCM default or Auto Audio capabilities on S PDIF Use this to set the S PDIF audio format to PCM default or Dolby Digital You can also set this to Not connected Easy Link mode For future use TV format Use this to set the format of the high definition video that is output on the HDMI connector of your HD receiver You can set this to 16 9 Pillar Box default 16 9 Full Screen or 16 9 Zoom These options determine how standard 4 3 programmes show on a TV with aspect ratio of 16 9 Note that you can directly change this setting using the picture format button your remote control The Auto and Dolby Digital settings on HDMI or S PDIF are not recommended until your HD receiver has been updated with the appropriate software Visit www philips com support regularly to check if the relevant software update is available Automatic eco mode Use this to set the time after which your inactive HD receiver automatically
17. press gt or OK Use the number buttons to first enter your current PIN code and then enter your new PIN code Use the number buttons to enter your new PIN code again for confirmation If you correctly entered the PIN codes your HD receiver briefly displays a message confirming that your PIN has been changed and then returns to the Parental Control menu Note Your new PIN code can be any 4 digit number other than the default PIN code 0000 A Press or BACK to return to the Settings menu Retuning your HD receiver EX From the Settings menu use V to highlight Set up and press gt or OK El In the Set up menu that appears make sure Channel installation is highlighted and press gt or OK EX In the Channel Installation menu that appears make sure Re tune is highlighted and press gt or OK Using more of your HD receiver HD set top box Settings Set up Channel una hart Automatic update Search for new channels A progress screen displays to confirm that the search is taking place Press the green button to save any new channels and return to the Set up menu Press the red button to cancel the search and return to the Set up menu e Note The Network messages menu under the Settings menu alerts you of any changes to your network such as recently added channels services etc To save time check this menu before retuning your HD receiver Updating your H
18. screen width Software update is starting LO to L100 indicate that the software is being loaded SO to S100 indicate that the software is being loaded End indicates a successful update FAiL indicates a failed update Huta Automatic resolution adjustment recommended other possible settings are indicated as 576i 576P 720P 180i for 1080i and 180P for 1080p liste Your HD receiver is in the first installation setup 20 Using more of your HD receiver 5 4 Using the Main menu l Press MENU to display the Main menu HD set top iow TV qu de amp echoing Access programme information Favourites ard mange your recordings Settings Use A to highlight a setting Press gt or OK to confirm your choice Press BACK to return to the Main menu Press BACK again MENU or EXIT to remove the Main menu Note Use the colour buttons to perform contextual actions which are described at the bottom of the screen El Use Y to highlight either TV channels or Radio channels and press gt or OK The menu now displays the selected full channel list All TV or All Radio and the existing favourite lists HD set top box Favourites TV channels 1 AH B WIR ENG EZ Action 167 HOI EMG BZ Action TV 802 ENG EZ Fight TV 803 ENG BY Mars TV ADA EMG EZ SF 16 9 TV Wo 60 ENG BZ SF TW A fie EFHO RZ Horror TV WO ROT CHG NE Future T
19. t BEC ZW BEC THREE CEBC Chan RAC HEWA 24 BECI Tiu F5 Mni Fr 26 Mar at gt Mar un ZH Mar Mon 29 Mni ae Dg This AAC THREE AIC THRET Relresahing TV far the digital age Tuna in dally fram 700 pin El Press GUIDE BACK or EXIT to remove the TV guide Notes You can also schedule a recording using the TV guide see page 16 Some channels may not offer an extensive TV guide 15 IE 72 UO Z 4 8 Scheduling stopping recordings To record a programme you must first connect your HD receiver to your VCR or any recording device using a SCART cable see page 28 and then schedule a recording using the TV guide or by setting a recording timer Using TV guide EN Press GUIDE to display the TV guide UseA Y lt gt to highlight the programme you want to record and press OK In the menu that pops up press one of the following OK again to confirm the scheduling of the recording EXIT to return to the TV channel that you were watching prior to displaying the TV Guide BACK to return to the TV Guide Hi box TY guisa 10 00 1030 11 00 250 12 30 Hot House Thrassgh amp Fimbla The Prat School School School u Saa School Working Lu Tria ia EC THREE CBRC Chanm En English Loo a Hum Word English English Look a Pr English E 24 RAC Mans Mon QUE CHE Wal Bargain Hu
20. Choose Cancel te delete it KA Press EXIT to return to watching live TV or press Menu to return to the Main menu 4 9 Using the Tools menu You use the Tools menu to display subtitles change the audio language control audio description and synchronise audio with video EX Press OPTIONS EJ to display the Tools menu Using your HD receiver Use A Y to highlight the setting you want to change Tools Auntie doser e date reel Lip syne El Press gt or OK and then press A V to select an option from the list that appears on the right You can change these settings using the Tools menu Subtitles Off default Available languages depend on the broadcast programme Audio language Audio description On Off default Set the audio description volume Available if Audio description is turned on and broadcast Audio desc level Set the DIGITAL audio output delay to synchronise audio with video Lip sync l Press 4 to save your changes and return to the tools menu Press OPTIONS GJ BACK or EXIT to remove the tools menu 17 un UO Z 5 Using more of your HD receiver 5 1 HD receiver Front panel DNS 7 1 Standby indicator Red initialisation mode and standby mode Orange active standby mode 2 standby button Switches your HD receiver into or out of standby 3 P amp P buttons
21. D receiver s software manually You can manually update your HD receiver software using a USB memory stick l Download the latest software file from the Philips website www philips com support unzip it and transfer it to USB memory stick Be sure to place the downloaded file in the top level folder of your USB memory stick Connect your USB memory stick to the USB connector on the rear panel of your HD receiver From the Settings menu use V to highlight Set up and press gt or OK l In the Set up menu that appears use V to highlight Software update and press gt or OK 25 72 UO Z HD set top box Settings Channel installation Start Signal quality Antenna powering Antenna output m avatem Information Sol tuas e update Factory rest Sonch and intel n software for the set top box Set up Sol twnre update Your HD receiver locates the software available on your USB memory stick and displays a confirmation message Press the green button to install the software immediately Press the red button to cancel and return to the previous menu If you press the green button your HD receiver updates the software and restarts You may depending on the update then be required to complete the first installation setup see page 10 Restoring factory default settings EN From the Settings menu use V highlight Set up and press gt or OK
22. DTR 5520 www philips com support For support call 0800 331 60 15 EN High Definition Digital Terrestrial Receiver designed by Face PHILIPS Table of contents U 1 Important 4 71 Accessories and connections 28 1 1 Safety information 5 71 Connecting your audio equipment 28 1 2 Reducing power consumption 6 7 2 Connecting your recording equipment 28 7 3 Connecting your 2 Your HD receiver 7 standard definition TV 29 2 1 What s in the box 7 2 2 What you also need not supplied 8 8 Guarantee and service 30 2 3 Overview 8 2 4 How to read this manual 2 9 Technical data 30 2 5 How to use the menus 9 10 Frequently asked questions 32 3 Getting started 9 3 1 Preparing your remote control 9 11 Glossary 35 3 2 Connecting your HDTV 10 3 3 Installing your HD receiver 10 12 Index 36 3 4 What if no channels are found 12 Contact information 37 4 Using your HD receiver 13 4 1 Standby wake up 13 Trademarks and partner logos 38 42 Switching on and off 13 4 3 Changing channels 13 4 4 Adjusting volume 13 4 5 Using the channel banner 13 4 6 Using channel lists 15 47 Using the TV guide 15 4 8 Scheduling stopping recordings 16 4 9 Using the Tools menu 17 5 Using more of your HD receiver 18 5 1 HD receiver 18 5 2 Remote control 19 5 3 Front panel display messages 20 5 4 Using the Main menu 21 6 Maintenance 27 6 1 Cleaning 27 6 2 Replacing 27 6 3 Disposing 27 1 Important Thank you for purchasing a Philips product
23. El In the Set up menu that appears use V to highlight Factory reset and press OK twice HD set top box Settings Channel installation Signal quality Antenna powering output information Sol update Factory react Return to factory settings Setup 2 Factory reset A message appears asking you to confirm If you are sure press the green button or press the red button to cancel and return to the previous menu If you press the green button your HD receiver restores the factory default settings and restarts You will then be required to complete the first installation setup see page 10 26 Resetting your HD receiver to the factory default settings erases all of your preferences and settings For example all of your favourite lists and recording timers will be erased Changing other system settings From the Settings menu use V to highlight Set up and press gt or OK The Set up menu appears HD set top box Settings ET Ang _ Channel installation Channel imstaliation Signal quality Re tTune Automatic update Antenna powering Antenna output System informatin wpdata Factory Feat Chane atni ch l To turn on or off the channel updates that automatically happen when your HD receiver is in the active standby mode make sure Channel installation is highlighted and press gt or OK Press V
24. V or if you want to record a programme to an external recording device n such as a Video or DVD R recorder TV 2 3 Overview Front panel Front Panel 1 Standby indicator 2 Standby button 3 Programme buttons 4 Resolution button 5 V Out button 6 Display 7 HD indicator Rear panel Rear Panel 1 5 6 8 10 1 Antenna IN 2 Antenna output to TV VCR antenna signal 3 RJ45 Ethernet connector 4 USB 2 0 connector 5 HDMI connector 6 AUX SCART connector 7 8 9 1 Remote control 2 4 DIGITAL audio out digital L R audio out analogue ON OFF switch 0 12V power connector 9 Safe extra low voltage 3 5 Remote control 1 Standby 2 Menu Text Picture format Radio Exit 3 Guide Options Up Down Left Right OK 5 Info Back m 4 Volume control Programme Mute 5 Alphanumeric keypad Audio description Subtitles D 8 Your HD receiver 2 4 How to read this manual Danger Describes situations of injury or loss of life Warning Describes actions that may cause damage to the product Caution Describes actions that are required to avoid dangerous or illegal situations Note Additional information Tip Information that is useful to know but not essential to the task For example information about alternative use 2 5 How to use the menus l Press MENU GUIDE OPTIONS o
25. Y Coste The AN TV list can not be mvdili c Choose Create to crente n new channel liat 5 4 1 Managing favourite lists Your HD receiver allows you to create favourite lists that include the channels you watch the most This lets you access your favourite channels quickly instead of scrolling through the entire list Creating a favourite list l On the Main menu make sure that Favourites is highlighted and press gt or OK The Favourites menu appears Press the red button to create a new favourite list Your HD receiver by default names the new favourite list as List1 for TV channels or RLst1 for radio channels You can create up to four separate TV and radio favourite lists To rename these lists see page 22 To add a channel to your favourite list use V to highlight a channel and press OK HD set top box Favourites List 1 4 All TV 4 B00 ENG BZ Action 16 9 TV wf 800 ENG BZ Action 167 B03 ENG BZ Mars TV B02 ENG BE Fight TV 805 ENG BZ 901 ENG BZ Action TV 807 EHG HZ Fight wi ENG BF Mars TV ES lt gt ENG BZ SF 16 9 TV WU nos AZ Horror TV gt CNG BIZ Future TV Done This channel belongs to the list Press OK to remove It Choose when your list is ready HD set top box Favorites TW channels Radio channels Manage your tnvaurit
26. a standard 4 3 TV D DHCP Dynamic Host Configuration Protocol DHCP is a network protocol that enables a router or server to automatically assign IP addresses to devices that are part of its network Digital audio Digital sound is available when you use the DIGITAL audio connector coaxial S PDIF on the rear panel of your HD receiver These sockets send audio through multiple channels instead of just two channels as analogue does Dolby Digital A surround sound system developed by Dolby Laboratories containing up to six channels of digital audio front left and right surround left and right centre and subwoofer DVB Digital Video Broadcasting n EPG Electronic Programme Guide Glossary EasyLink The Philips EasyLink M technology enables you to control multiple devices which are connected through standard HDMI cables using a single remote HDCP High bandwidth Digital Content Protection HDCP is a type of digital copy protection system When your set top is attached via an HDMI cable to an HDCP compliant HDT V the HDTV and set top negotiate a secure link which allows your set top to transmit full resolution video to your HDTV HDMI High Definition Multimedia Interface HDMI is a high speed digital interface that can transmit uncompressed high definition video and digital multi channel audio It delivers perfect picture and sound quality completely free from noise HDMI is fully backward compati
27. ap teaching and qao back previous Seren Use A V to highlight the network that you want to install and press the green button progress screen displays to confirm that the search is taking place When the search is complete a screen displays the number of TV and radio channels that your HD receiver has found Your HD receiver automatically saves these channels Press the green button to go to the next step Note In case your HD receiver does not find any channels see the What if no channels are found section on page 12 Note If you are in an area that receives signals from more than one network and possibly variant of the same channel e g BBC1 BBC1 Scotland then your HD receiver will prompt you to select the network and channel variant that you want in the All TV and All Radio lists HD zele box Narnian _ Channel search Pound channels hawe beeen Chorus TY Channels 6 Radio Channels Previous Hex Ka gole code GMIT eran HE 260 bap box narnia Herework selection 2 Paire DHEZTHBHaobwork Hast Save AMOC HGN and camplate installation Getting started Note Digital terrestrial broadcasting is progressing throughout the UK Please note that the reception of digital signals may need to be verified as it can be adversely affected by physical elements such as mountainous
28. ation Your HD receiver is powered using a 12 V power supply unit Your HD receiver has been manufactured to meet the appropriate safety standards but you must follow the below instructions to operate it safely Keep these instructions for future reference m Warnings Your HD receiver does not contain any user serviceable parts Do not attempt to open it All maintenance work must be carried out by qualified services centres Before connecting the 12 V power supply unit to the mains check that the mains supply voltage corresponds to the voltage printed on it If the mains voltage is different consult your local dealer The 12V power supply unit has been designed for indoor use only Use only the original 12 V power supply unit To prevent fire or shock hazard do not expose your HD receiver to rain or moisture Place your HD receiver on a firm surface and do not cover the ventilation openings with items such as newspapers table clothes curtains etc Do not install your HD receiver near heat sources such as radiators stoves or other equipment that produce heat Protect it from direct sunlight In order to ensure a free flow of air around your HD receiver allow at least 5 cm of space above and around it This prevents overheating of your HD receiver Do not place any combustible objects such as candles etc on your HD receiver Never stand objects filled with liquids such as vases on top of your HD receiver Do not place anything on
29. ble Coaxial RF cable AC DC power adaptor incl mains cord Miscellaneous Temperature range C Operating 5 to 45 C Storage 25 to 70 C e Mains AC 230V 10 50 Hz Power consumption lt 6 W Standby lt 1 W Off mode 0 3 W Weight 1 4 kg Including packaging 2 3 kg Dimensions Product mm 290 x 160 x 37 Packaging mm 370 x 235 x 70 Due to continued product improvement this specification may change without notice 31 un UO Z 10 Frequently asked questions Connection Your HD receiver does not display any digital TV channels on your TV You may also see the on screen message Signal lost e Check that the aerial cable from the aerial wall socket is correctly connected to your HD receiver see page 10 e There may be a temporary problem with the reception caused for example by bad weather try again later e Check if there is any network message related to this signal loss You can access the Network messages menu from Menu gt Settings gt Network messages Setup Your HD receiver does not seem to be working and there are no lights on the front panel e Check that the 12V power supply unit is correctly connected to your HD receiver e Ensure that the ON OFF switch on the rear panel of your HD receiver is switched on is in the 1 position Your HD receiver does not seem to be working and a channel number is shown on the front panel display e
30. ble with DVI HDTV High Definition Television Lip Synchronisation Setting used to synchronise audio with video in case a delay is experienced in particular if speech does not match lip movements Motion Picture Experts Group A collection of compression systems for digital audio and video Code 4 digit code used to prevent access to inappropriate programmes parental control 35 IE 72 x UO Z SDTV Standard Definition Television Surround A system for creating three dimension sound fields full of realism by arranging multiple speakers around the listener USB memory stick A small size storage device which is used to update your HD receiver s software see page 25 Connect it to the USB 2 0 connnector on the rear panel of your HD receiver 36 12 Index Change channel 13 15 Channel banner 13 14 Connect HDMI 10 SCART 29 Control volume 13 F Favourite lists Create 21 Delete 22 Modify 22 Rename 22 Front panel 18 LE Indoor antenna Setting 26 Powering 10 27 Install First installation 10 Rear panel 18 Record Programmes 16 Stop 16 32 Remote control 19 Restore factory settings 26 Retune 25 Return channel 24 Software update 25 System settings 26 Switch on and off 13 TV guide 15 Wake up your HD receiver 13 Index Contact information 72 Z DTR 5520 05 Serial number UNITED
31. company Although you set Audio capabilities to Auto for HDMI or Dolby Digital for S PDIF your HD receiver does not deliver Dolby Digital 5 1 multi channel audio output e Your HD receiver needs a software upgrade e Visit www philips com support regularly to check if the appropriate software for ugrading your HD receiver via USB is available Set the Audio capabilities setting to PCM until the upgrade of your HD receiver is done 34 You get a picture or a freezed picture a program number on the front display and your receiver seems blocked while not responding to the remote control commands Your HD receiver has hung up You have to reset your HD receiver Press the standby button on the front panel until Init is Shown on the front panel display If you have tried all of the actions suggested above and still are not able to resolve the problem contact your local Philips Consumer Care Centre see page 37 Frequently asked questions 11 Glossary Analogue audio Analogue sound is output from the LEFT RIGHT audio connectors on the rear panel of your HD receiver The red and white sockets send audio through two channels the left and right Aspect ratio Aspect ratio refers to the length to height ratio of TV screens The aspect ratio of a standard TV is 4 3 while the ratio of a high definition or widescreen TV is 16 9 The letterbox format allows you to watch a video with a wider aspect ratio on
32. ctrical S PDIF cable not supplied Refer to the user manual of your audio equipment to choose the proper digital audio input ES Note With a digital connection via the DIGITAL output of your HD receiver mute and volume operations are managed by your audio equipment and not by your HD receiver Option B Analogue connection Connect the L R audio outputs to the relevant audio inputs of your audio equipment using a double CINCH cable not supplied Refer to the user manual of your audio equipment to choose the proper analogue audio inputs Option C HDMI connection Recent amplifiers are fitted with one or more HDMI source input s and one HDMI output 28 Recommended connection Connect the output of your HD receiver to an HDMI source input of your amplifier Connect the output of your amplifier to an HDMI input of your TV System settings For your HD receiver set the Audio capabilities on HDMI setting under Menu gt Settings gt Preferences gt Digital output to AUTO Select the correct A V source on your TV Select the correct A V source on your amplifier Volume controls and necessary Lip sync adjustments are performed by your amplifier Refer to your amplifier s user manual 7 2 Connecting your recording equipment Aerial wall socket HD receiver E Mains wall VCR socket Kl Connect the aerial cable
33. e channel Hata TW channels 1 Using more of your HD receiver To remove a channel from your favourite list use V to highlight it and press OK B When you are finished adding all your channels press the green button Press to return to the Favourites menu 21 IE 72 UO Z Renaming favourite lists From the Favourites menu use A Y to highlight either TV channels or Radio channels and press gt or OK The menu now displays the default channel list TV or All Radio and any existing favourite lists UseA Y to highlight the favourite list that you want to rename and press the blue button EX In the Rename list menu that pops up use V or the number buttons to rename your favourite list Press the green button to confirm or press the red button to return to the previous menu without saving any changes HD set top box Favourites To add a channel press the red button Then use A V to highlight the channel you want to add and press OK Press the green button to save your changes To remove a channel use A V to highlight it and press the green button reorder the channels in your favourite list use V to highlight a channel you want to move and press the blue button Use V to move the channel up or down and press OK B Press 4 to return to the Favourites menu Deleting favourite lists From the Favourites
34. energy consumption to zero by unplugging it from the mains wall socket In the off and standby modes your HD receiver cannot receive updates from the network However at receiver wake up you will be prompted by a message if an update notification has been received Front panel standby Typical power Typical annual indicator and display consumption W energy use kWh Power Not lit up adaptor unplugged Standby Standby indicator is 0 86 red Active Standby indicator is 5 00 15 Standby orange A channel number is 5 80 shown on the display Based your HD receiver being On for 4 hours daily and being in standby for 20 hours 6 Important 2 Your HD receiver Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome 2 1 What s in the box 12V power supply unit HD receiver HDMI cable RF cable gt PHILIPS j User manual Quick start Freeview flyer Retune flyer guide 8 76 Jef Da Ha Doo PHILIPS Remote control and 2 x AAA batteries a Caution Plastic bags can be dangerous To avoid suffocation keep the bag away from babies and children Your HD receiver un UO Z 2 2 What you also need not supplied SCART cable required only if you have a standard definition T
35. enters into the active standby mode You can set this to off 3 hours default 4 hours 5 hours 6 hours 7 hours or 8 hours Return channel Use this to configure your HD receiver to connect to the internet which then serves as a return channel to your Digital TV service provider The return channel is necessary to use any interactive applications that your Digital TV service provider may offer Before configuring the return channel be sure to connect your HD receiver to your network router using an Ethernet cable Then choose either DHCP to set up your connection automatically or manually enter all the parameters like IP address Network mask Gateway and DNS settings to match your router s settings 24 Default volume Use this to set the default volume at wake up of your HD receiver Changing parental control settings EN From the Settings menu use V to highlight Parental control and press gt or OK The Parental control menu appears HD set top box Settings Parental control Parental control limits Parental control limits ort Child timer s High Channel boeck hel acus Change PIN code Low Saleen thee limit of the parental control E To change the parental control severity settings use V to highlight Parental control limits and press gt or OK Use A V to highlight the severity level you want to set and press lt or OK to save your changes and return to the previous menu N
36. essage after a few seconds Tank you for berging HO terrestrial PHILIPS a WR Nest it amro ion and ga a Antennae paewerlng serena El Press the green button to start the installation The Antenna powering menu appears HD zele bee Marnar Antenna powering Ore Cir Select 18 you unes na antenna powered by the RF of the HE cet fop box Hex t amro ion and ga Ea Iv shape selection creen l Let the Antenna powering setting be Off unless you use an indoor antenna that can be powered by the coaxial cable connected to the Antenna IN socket of your HD receiver see note Note Your HD receiver can only deliver 50 mA current under 5 V so refer to your indoor antenna s user manual to check if its power requirement fits the capability of your HD receiver Getting started Press the green button to confirm The TV shape menu appears HE zele box TW shape m 4 2 Em i167 Hax fao sse malection and qn ta channel tpa ch scream Let the TV shape setting be 16 9 if you use an HDMI connection to your TV Press the green button to confirm and start scanning for the available channels HI 260 tap hoax Channel search amp emrch in progress Progress 3 2 Channel search In EE Prout Ea st
37. et connection please contact your local Philips Consumer Care Centre see page 37 30 2 Technical data This product is in conformity with European 95 47 EC and 2002 21 EC directives The product complies with the following European council Directives 2006 95 EEC and 2004 108 EC Video decoding Standard definition e MPEG2 MP ML e MPEG4 AVC MP L3 Video bit rate 15 Mbit s Resolution 576i max 720x576 pixels interlaced Picture format 4 3 et 16 9 High definition e MPEG2 MP HL e MPEG4 AVC HP L4 Video bit rate 20 Mbit s Resolution of broadcast 720p 1080i Upscale up to up to 1080p50 Content protection HDCP on HDMI Audio Decoding e MPEGI layer I Il Dolby Digital HE AAC stereo Multichannel Dolby Digital HE AAC to stereo down mixing Dolby Digital Plus to Dolby Digital transcoding HE AAC to Dolby Digital transcoding Feature subject to future product software upgrade Convenience Automatic installation HD reception indicator Automatic channel update TV and Radio modes 4 x favorite TV channel lists e 4 favorite Radio channel lists Program list editing Add Move Delete Parental control Child lock 8 days Electronic Program Guide Guarantee and service Event timer 8 Event programming via EPG DVB subtitling Digital TXT MHEG with Interaction channel e Video scaling on HDMI output Auto Original 576i 576p 720p 1080i 1080p50 Dolby
38. ion to English default Gaelic Welsh or Irish Audio language Use this to set your preferred audio language to English default Gaelic Welsh or Irish Default subtitles mode Use this to set how you prefer to display subtitles Using more of your HD receiver You can set this to Activated Not activated Auto when no correct audio default Auto when audio is muted or For hearing impaired Subtitles language Use this to set your preferred language for subtitles to English default Gaelic Welsh or Irish Recording Record Link Use this setting to enable or disable the control by your HD receiver of the start stop recording function of your Video or DVD R recorder see the note on page 29 Analog output Video on AUX Scart Use this to set the type of analogue video signals that are output on the AUX SCART connector of your HD receiver You can set this to RGB default when V Out is set to AV or CVBS default when V Out is set to HDMI e Audio on AUX Scart This setting applies when your HD receiver is connected via a SCART Cable to a standard definition TV Use this to set the type of analogue audio signals that are output on the AUX SCART connector of your HD receiver You can set this to Mono or Stereo default TV format Use this to set the format of the analogue video that is output on the AUX SCART connector of your HD receiver You can set this to 4 3 Letter Box 4 3 Centre Cut Out
39. m Subtitle s Audio lanquages Current channel list 850 momi Next in 40 minutes Torchwood Time before next program starts Network change information _ Current program name Next program name Start time End time progress status of current program 14 Using your HD receiver 4 6 Using channel lists You use the channel list menu to switch to any TV or radio channel from the TV or All Radio channel list or your favourite lists Changing channel Press OK to display the current channel list Use A Y to select the channel you want to watch Press to preview the channel press OK again to watch it Changing current channel list Press OK to display all the channels of the current channel list Eno ENG Bz Action 161 BOI ENG EZ Action TV gt EMG DZ Fight E 09 AT Mure TY Ce KOA CHO UE SF TV ER ROS CHO DZ SF TU noo DE Horror TV e nn EMO HE Futura TV Press 4 to display all the available channel and favourite lists To create new favourite lists see page 21 Channel lists List 1 m List List 3 mi 11 14 n adio Hist nim Histo amb Peta El Use A Y to highlight the list you want to use l Press OK to confirm and display all the channels of the selected list Use Y to highlight a channel and press OK to preview
40. ng HEC 2 BEC THREE amm Evening 3 jump ta 11 50 20 rin Dry Diy Schools Saa You Sea Propramane ia achediuled far dico ding IMPORTANT NOTE If the scheduling is made on a Now programme highlighted in blue your HD receivers starts recording instantly and is locked on the programme to secure its recording Any attempt to control the receiver displays on your HD receiver s front panel You must STOP the recording to recover the control of your receiver If the scheduling is made on a later programme your HD receiver will record it at the set date and time The program is highlighted in red in the TV Guide 16 HOW TO STOP A RECORDING When a programme is being recorded you cannot switch to any other channel or use any of the other features of your HD receiver TO STOP CANCEL A RUNNING RECORDING and return to normal live TV press EXIT first then OK immediately after Using recording timers l Press MENU to display the Main menu Make sure that TV guide amp scheduling is highlighted and press gt or OK The TV guide amp scheduling menu appears El In the TV guide amp scheduling menu use V to highlight Scheduled recordings and press gt or OK The Scheduled recordings menu appears HD set top bos TV guide amp scheduling Scheduled recordings Hew manual recording es Kate a Schools Ses You See mrt Enel
41. not supplied from the aerial wall socket to the Antenna IN connector on the rear panel of your HD receiver El Use the supplied cable to connect the connector on the rear panel of your HD receiver to the HDMI input connector of your T V Accessories and connections Use a SCART cable not supplied to connect the AUX connector on the rear panel of your HD receiver to the SCART input connector of your VCR or other recording equipment l Connect your HD receiver and other equipment to the mains Notes Double Scheduling To succeed making recording do not forget to set timers on your video or DVD recorder according to your HD receiver s recording schedulings How to avoid double scheduling Your recorder is fitted with a feature allowing its start stop control compatible with your HD receiver The recorder function is activated by the video signal at its SCART input Once the function is active the recording starts when video is on and stops when video is off If your Video or DVD R recorder supports the above function the simple scheduling of your HD receiver will automatically control your recorder Necessary system installation Enable Recorder Control on your Video or DVD R recorder Refer to the user manual of your recorder Set the Recording link setting of your HD receiver under Menu gt Settings gt Preferences gt Recording to ON Accessories and connections 7 3
42. nus channel banner and channel lists Used in contextual menus and MHEG applications Open close Tools menu Move up down left right within lists or menus Return to the previous channel or menu screen Change channel up down Alphanumeric keypad Turn subtitles on off Turn Audio Description on off Turn volume up down Mute restore sound Open close channel banner Confirm selection or schedule a recording in the guide Open close guide Open close MHEG applications Change picture format setting 19 IE 72 x UO Z 5 3 Front panel display messages Em Your HD receiver is starting up Your HD receiver is tuned to TV channel 25 Your HD receiver displays r025 when it is tuned to radio channel 25 rEC is displayed each time you press a button on your remote control to indicate that A recording is in progress Your HD receiver is locked on to the programme being recorded To unlock your HD receiver you must stop the recording by pressing EXIT and then OK BM Antenna signal is not available Subtitle on oFF indicates that subtitles are turned off E sin men gen omeen o EE weesen 000002 EER vou HD recenerissvtchingtostndoymade OOO O BEEM Worn she ace AN recommended ofyour HD ec Picture format is 4 3 with black bars 16 9E indicates that the picture format is 4 3 stretched to 16 9 16 90 indicates that the picture format is 4 3 zoomed in to the
43. o button to control the quality of ther sig Provided by your antenna Previous ter slaat cae chine impair or Check elle button to The of than signal ger Gy yor rt Pure If your HD receiver is still not able to find any channels press the yellow button Use A V to manually check the quality and strength of the signals received by your antenna in various channel frequencies HD zele box Signal quality test Fa tha chanel bo Channel UHF 56 BE34MHz Like Hilir to fag weer Tc Signal stremgtih quell Ey Excel WE Pr minut Prewviniis Ea 45 hack Eo welcome icri Note Your new PIN code can be any 4 digit number other than the default PIN code 0000 Press the green button to confirm your choice and complete the installation You can now start using your HD receiver 12 If the Signal strength bar is green then your antenna and HD receiver are properly connected If it is red then you need to first check your connection If the Signal quality bar is green then you can be sure that you are receiving digital broadcast signals If your reception is not optimal few channels or blocky image you must check your antenna installation as it may need to be realigned or fixed Getting started Using your HD receiver 4 1 Standby wake up
44. on about your HD receiver press V and highlight System information Details such as software version model number serial number etc are displayed on the right Press lt or BACK to return to the Settings menu Maintenance 6 Maintenance 6 1 Cleaning For cleaning use a soft damp not wet cloth Never use any abrasive cloth and aerosol cleaners 6 2 Replacing Your HD receiver does not contain any user serviceable parts Do not attempt to open it All maintenance work must be carried out by qualified service centres 6 3 Disposing Your HD receiver is designed and manufactured with high quality materials and components which can be recycled and reused Please inform yourself about the local separate collection process for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste The correct disposal of your old product will help prevent potential negative consequences for the environment and human health 2 72 i UO Z Accessories and connections 7 1 Connecting your audio equipment HD receiver Audio Equipment 2 97 HDMI HDMI Digital Option Electrical S PDIF connection Digital Connect the DIGITAL audio output of your HD receiver to the relevant audio input of your audio equipment using an ele
45. ote that if you set the Parental control limits to Off che child timers and channel lock settings see below will not have any effect Note When Parental control limits is set to ON menu items like Parental control and Set up will be protected by the PIN code EJ To create a new child timer use A V to highlight Child timers and press gt or OK Make sure that Define child timer is highlighted and press gt or OK HD set top box Settings Parental control Child timers Child timers Start time 12 03 End time 14509 Share time GE Repeat mode ince Date LENDE Cancel col Select the time at which access will be granted without FIM code Using more of your HD receiver Use A W lt P to set the time period during which you will be able to watch any unlocked channel without having to enter your PIN code Press the green button to confirm To delete the child timer make sure Modify child timer is highlighted and press the red button To modify the child timer make sure Modify child timer is highlighted and press or OK Make the required changes and press the green button to confirm To lock a channel use A V to highlight Channel lock and press gt or OK Use A V to highlight the channel you want to lock and press OK Press lt or BACK D to return to the previous menu change your PIN code use A V to highlight Change PIN code and
46. r INFO on your remote control to display the Main menu TV guide Tools menu or channel banner respectively Use A V lt gt to navigate through the menus and change any setting Press 4 or OK to confirm your choice l Press EXIT to remove the menu For more information see pages 13 to 27 Getting started 3 Getting started 3 1 Preparing your remote control fr LI 1 2 l Remove the battery cover by gently pressing down in the small circle on the cover and sliding it downwards Insert the two AAA batteries as shown Be sure to match the and marks on the batteries to their respective marks inside the battery compartment 3 Replace the battery cover Note For better reception point your remote control directly at the front panel of your HD receiver while pressing any button Caution Do not leave batteries in your remote control for long periods of time without use Replace both batteries at the same time Do not dispose of used batteries with your domestic waste Used batteries should be recycled at the end of their useful life Do not dispose of batteries in a fire un i UO Z 3 2 Connecting your HDTV o Danger Risk of electric shock Before making any connections ensure that your equipment is disconnected from the mains 0 Aerial wall socket HD receiver
47. s To set the length of time that the channel banner remains on screen see page 23 Note While recording a programme to an external recording device such as a VCR the channel banner overlay will not be recorded Changing channel To change the channel display the channel banner by pressing INFO When the channel banner is on screen use V to see what programmes are currently showing on other channels If you see a programme you want to watch press OK EX jJ Au Tw F 01 ENG iz Action TV HI GC GOD ota To display more information about the current programme on the channel listed in the channel banner press INFO i again F ENG DZ Action TV Hews u TW EH C GD otras 2000 X 8002 cn ed pole nkinq Off Enemy Line Hunt fost page Choose Nest to zen Information miscuit next arenas 13 To display what programme is on next on the channel listed in the channel banner press the yellow button Press INFO a third time or press EXIT to remove the channel banner without changing the channel Alternatively press BACK to return to the channel banner 4 5 1 More about the channel banner content Channel number Current time Channel name Multi channel digital audio output select and watch a program among those broadcast now Press A V to choose desired program Press OK to watch the selected progra
48. t the missages related ta the metwark update Press or BACK to return to the Main menu Using more of your HD receiver Setting your preferences From the Settings menu use A V to highlight Preferences and press gt or OK The Preferences menu appears HD set top box Settings Preferences _ m Display Banner duration Language preferences Timer warning duration Recording Front panel brightness Analog output Digital output Automatic eco mode Retin channel Dainu waelurna on screen disgplmy preferences Use A 4 5 OK to navigate through the settings and options and make changes Press 4 or BACK to save your changes and return to the previous menu You use the Preferences menu to change these settings Display Banner duration Use this to set the length of time 3 to 10 seconds that the channel banner remains on screen when you change channel By default it is set to 5 seconds Timer warning duration Use this to set how soon before the start of a program should the record timer alert you The available options are 30 seconds before 1 minute before default 2 minutes before or 5 minutes before Front panel brightness Use this to set the brightness of the front panel display You can set this to Low Medium default or High Language preferences Information language Use this to set your preferred language for displaying programme informat
49. to highlight Automatic update and press gt or OK Use A V to highlight On or Off Press 4 or BACK to save your changes and return to the previous menu To check the signal quality of any channel that you are receiving press V to highlight Signal quality and press gt or OK In the Signal quality test menu that appears use V to select a channel that you want to check Press 4 or BACK to return to the previous menu l To turn on or off powering your active indoor antenna using the Antenna IN connector on the rear panel of your HD receiver press V to highlight Antenna powering and press gt or OK Use A V to highlight Off or On Press or BACK to save your changes and return to the previous menu Using more of your HD receiver Set Antenna powering to On only if you need to power an active indoor antenna that requires a 5 V power supply not exceeding 50 mA current consumption Be sure to read your indoor antenna s user manual before turning this setting on To control antenna output press V to highlight Antenna output and press gt or OK Use A V to highlight Inactive in eco mode or Always active Press or BACK to save your changes and return to the previous menu ES Note If Antenna output is set to Inactive in eco mode while Antenna powering is set to On the device s connected to the To TV VCR output will not receive the antenna signal To see informati
50. your HD receiver that might drip or spill into it If this happens disconnect the 12V power supply unit from the wall socket and have your HD receiver checked at any authorized service centre The batteries installed in the remote control should not be exposed to excessive heat such as sunshine fire or the like Please also pay attention to all the warnings and cautions listed throughout this manual Important un Z 1 2 Reducing power consumption Your HD receiver is designed to reduce its impact on the environment and complies with the European Directive 2009 125 EC This is part of Philips ongoing commitment to lead the way in environmental responsibility It has a standby mode of operation that needs very little power See the table below and please note that When your HD receiver is in the standby mode you save energy and therefore money and reduce carbon dioxide emissions that damage the environment You use the standby button on your HD receiver or remote control to switch between on and standby modes In addition if your HD receiver is on but you do not press any button on it or your remote control for 3 hours configurable see Automatic eco mode on page 24 your HD receiver will automatically get into the standby mode You use the ON OFF switch on the rear panel of your HD receiver to turn off your HD receiver f you are not going to use your HD receiver for several days you can cut its

Pace DTR5520 - User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents