Laminating Machine User Manual
Contents
1. membrane and the glue Become transparent it shows glue full dissolved That s a suitable temperature with best laminating effect Partially non transparent or non transparent totally this shows inadequate temperature and the glue is not fully dissolved C Not only the contact part become transparent but also it extend to other parts and even the predeposited membrane is nearly dissolved This is caused by high temperature Clutch and Gears There are two clutches on the two sides of the glue roller Rotate the nut counterclockwise to loosen it There are two holes indicate tow tap position Put the clutch screw into the upper hole and the glue roller collected The roller separated when the screw is put into the lower hole and it is convenient to clean papers and dirt Please put the clutch screw into the lower hole when the laminator is not used for a long period to avoid the glue roller deformation under pressure Thin Paper tap position is suitable for paper less than 350g Thick Paper tap position is suitable for paper over 3 side There are two which is used t has been adjusted nd could be used imbalanced the membrane may have some tiny bubbles or wrinkles caused by inadequate pressure as the right picture shows And pressure adjustment is needed When wrinkles appear you need to check the membrane on each side of the glue r2. Laminating Machine User Manual Cautions 1 Please test your empty machine first after you received it Plug in the power wire and turn on the machine then test all the functions on the control panel If the machine cannot work se properly or after 3 minutes 80 C preheating and the green light does not turn press the cold button turn off the machine and contact us for help 2 Please finish reading our user manual first and get familiar with all the ma using It w degrees r off the machine 3 Inspect the temperature control sensor before ae i on roller surface to ensure the precise temperat backward and you will find the temperature sensor to adjust the temperature control sensor position should in cold mode while 80 C preheating Roller rotates and the predeposited membrane deforms while temperature is set up normally and the green light does not turn on C If the sensor failure happens please press the cold button immediately and contact us 4 Our machine is suitable for predeposited membrane of glue inside towards core Max laminating size 22cm laminator 8230 33cm laminator 8350 44cm laminator 8460 Membrane roll max inner diameter is 2 54cm and max diameter is 9 5cm 5 Machine maintenance A Keep voltage stable with a regulator B Place the machine on a fixed platform and clean the machine with towels after power off 6 Single side laminating method A Onl
3. an Pull several centimeters membrane on the p upper glue roller and install the paper in platform Use the paper sheet to hold against the membrane head and the tension of the paper tow side should be balanced Align it to the seam of the upper roller and the lower roller Press the Enter button and the paper sheet will pass together with the membrane When the paper appears from the back of the laminator press Stop button to stop Install the Upper Membrane Read the right diagram of the upper membrane i Smooth Roller installation carefully The glue side should reve forwards the roll core and pass the membrane through the smooth roller first and them into the glue roller A K 4 v ay me eposit I tthe glue a a As the K 2 roll f nem Pass the upper membrane through the smooth roller and p it out As the right diagram shows take out sie sheet Use the paper sheet to hold agai If all the above procedures finished we can then prepare to laminate Laminating procedures as follows 1 Preheating Switch the power on and set Stop Hot 80 C mode and the machine will be in the preheating status 2 Laminating The OK green light will turn on in about 4 minutes and the preheating procedure is finished Put the first paper into the paper in platform and press the ENTER button Them set temperature to 100 150 C better to set temperature for actual needs imme
4. an be cleaned Prevent from scratches Improve printed paper and photo quality Writeable with certain membrane Improve paper tenacity a eS ee a E Avoid malicious modification after contract or d
5. diately and continue laminating 3 Almost before laminating finished When A4 paper is left with only 2 3 sheets set the temperature to 80 C and press the CLOD button Press the STOP button to finish laminating 4 Before laminating finished Laminating an additional paper any used thick paper is ok and without this additional paper the predeposited membrane may melted on the roller which may cause damages to the laminator After this paper appeared on the back of the machine press STOP button and finish laminating Power off the laminator several minutes later In the later future we only need to preheating and laminating It does not need to add membrane roll until the membrane is used up Laminating Temperature 1 Why some paper effect is good and some is not good with bubbles inside after laminating Answers The reason why bubbles happen is that some exceptional papers are not suitable for laminating and some are caused by inadequate temperature The p Y i thickness of the paper the quality and vic git toe ncet N paper PRTNDLAe OF work thickness of membrane and work environment coutd all i Please retest your best laminating temperat re en yo environment changed 2 Why the laminating effect is not that good while we followed the reference tempera provided gt Answers The reference tempe H result Different environment different laminating temp tact part of the
6. oller as the right picture shows If of the two sides membrane is flabby the temperature is too high and you need to decrease preheating or laminating temperature If only one side membrane is flabby this side glue roller pressure is inadequate and you need to add this side pressure or decrease pressure on the other side The pressure adjustment should follow the principle of tiny adjustment for several times The membrane is not need to detached but the temperature should adjust to 80 C One circle adjustment each time Picture 3 Laminate more papers to adjust pressure until the problem is solved Pressure adjustment is used for balance the pressure on the two sides of the glue rotier not just about pressure _ increase decrease on the other side is mer sometimes The laminator may be damaget assure is increase to the limit Tension ssure iS set to ers can adjust the e for actual needs used to control the tension or the lower membrane nterclockwise to loosen tension If the paper fringe is upturned after laminating you need to increase the lower tension And if the paper fringe is downward then increase the upper tension Fuse Replacement Our laminator has a spare fuse Open the fuse box in the power outlet with a straight screwdriver to replace the fuse Laminating Functions Real Waterproof Keep away from oxygen defer paper fade from oxygenation Dirt proof after laminating paper surface c
7. y one membrane not recommended It has to make sure that the predeposited membrane size is smaller than the paper size otherwise the membrane fringe may stick Z to the roller B Two papers laminating together recommended Two papers or photos bac laminating is more efficient and safe paper in platform Push the two rollers left and then take the Then prepare to install the predeposite As the picture shows the two roller needs to be align N with each other and it will reduce misplacement phenomenon effectively PAG U a Our laminator has to use predeposited membrane of Glue forward the roll core When winding the membrane the predeposited membrane has to pass the smooth roller In case of semma yea any lamination creases The prepare tow paper sheet 210x99mm for laminator 8230 297x105mm for laminator 7350 or 420x99mm for laminator 8460 Install the Lower Membrane Switch on the machine power set cold button and stop mode Read the right diagram of lower membrane installation the membrane glue side forwards the roller It will pass through the smooth roller and goes to the glue roller the predeposited side forwards the roll diagram steps and the glue side embrane should be forwards the roller Take out the lye catch the head y Aa N the smooth SA wes head through gicture shows with another S the le E p
Download Pdf Manuals
Related Search