"user manual"
Contents
1. 19 PR no Weseeesserss 21 Technical Specifications cccccccccccssssssssssssssssssssscsssccccccccccccscssscsssees sssssssss 24 A O A E 26 Description The Satellite meter is a handy digital antenna measuring device for an quick and easy alignment of satellite antennas If a satellite is found the meter shows it on the display and emits a audible signal Signal strength and quality are displayed as numerical values and bar graphs Another measurement value is the forward error correction FEC and the bit error rate BER Modulation error rate MER In addition the picture quality can be revised on the high resoluted 4 3 inch TFT LCD screen Many satellites are pre programmed in order to an quick antenna adjustment The scope of supply contains among the charger an USB connector which allows you to update software A carrying case serves as protection and for the transport It cares for better readability of the display at sunshine Safety instructions Attention Please read the safety instructions carefully before operating the device Please follow all warnings and instructions on the equipment and in the operating manual Safety of persons Ensure that nobody can be hurt by falling tools or parts of the satellite antenna during the adjustment and installation of the antenna For your own security use a rope on sloping roofs General information Attention The devise should2. Next idx 56 99 F1 Back F2 Screen capture Figue 7 C Signal info gt Press the lt or gt button to select the C frequency gt Press the F1 button to back C Finder menu gt Press F2 button to screen capture Lining C antenna up gt Press the C Finder button to display the menu C finding gt Choose a C Frequency and Bandwidth gt Turn the receiving antenna as long as the LOCK LED lights or the joists of the signal level and signal quality are green Once a signal is found the bar graph shows the signal strength and quality In addition C N SNR PowerLevel and a BER after BER are displayed In addition an acoustic signal is represented Notice The satellite call sign see Figure 7 registers which frequency you S receive at the moment At some frequency as for example 474MHz 2 8M a wrong frequency call sign is cosent on single transponders hence the announcement can be falsified Therefore we recommend to leave the setting on the preset first transponder with the search of a frequency Therefore the right frequency call sign is indicated in general always gt Set up the satellite antenna exactly to receive the best signal SCM6000 Notice The C N value should amount 6dB at least Values of 10dB and more are urgently if you liked to have a certain bad weather reserve Or in the case if the signal about a multicounter should be distributed to several buyers The higher the C N value the
3. Frequency range Input Level RF Input Output impedance Demodulator Front end modul Channel Bandwidth Corde Rate IEC 169 24 950 MHz 2150 MHz 65 dBm bis 25 dBm 13 18 V max 400 mA 22 kHz Version 1 0 QPSK 8PSK 1 5 Mbps bis 45 Mbps Auto conversion IEC 169 24 47 MHz 862 MHz 80 to 35DM 750 Unbalance 160 AM 64QAM 128QAM 256QAM 6MHz 7MHz 8MHz 1 2 3 5 2 3 3 4 4 5 5 6 Guard Internal SCPC und MCPC Spectral inversion System resource Processor Clock Frequency DDRII System DDRII Video FLASH Vide decoder Data rate Resolution Video format Connectors USB2 0 Enternet Hdmi CVBS Power supply Supply voltage Li oN battery Charger Supply voltage charger Dimensions 1 4 5 82 1 8 5 64 1 16 1 32 1 64 1 128 Auto conversion FUJITSU MB86H60 324MHz 64 Mbyte 64Mbyte 16 MByte up to 15 Mbit s 10801 720p 576p 480p PAL NTSC SECAM USB 2 0 Rj45 output 3RCA Video L Autio R Audio 14 V 3000 mA 90 240 V 175 250 V 50 60 Hz Length x width x height Gross weight 0 5 Kg Temperature Operating temperature 0 C to 40 C Storage temperature 40 C to 65 C Warranty
4. Select satellite button press the lt or gt button choose the Satellite name gt In the Scan method button press the lt or button choose the scan method mode at the Atuo Blind Manal gt In the NIT Search button press the lt or gt button choose the NIT search at the ON OFF gt In the Kind of service button oress the lt or gt button choose the Kind of service mode at the All services Only free services Only encrypted services gt In the TV Radio button press the lt or button choose TV Radio mode at the TV Only Radio Only TV Radio USB gt Press the USB button to display the Updating and Backup Data menu Finder 19 ENG SCM6000 Updating Ma NY Backup Data Figure 11 USB gt Press the File viewer to play usb file gt Press the Updating button or use the updating the sw gt Press the Backup Data to backup data Musicbox Pictures Software update Current software version is SmartGo HD 1 155 Previous software version was SmartGo HD 1 143 Fl Cancel Figure 12 SW updating 20 JENG SCM6000 Backup Data F1 Start Figure 13 Backup Data Angle calculation gt Press the ANGLE button to display the Calculation menu gt Press the lt or gt button or use the NUMERIC keys to change the configuration of the selected menu point Calculation SAT Longitude Local Longitude Local Latitude Calculate F1 Satellite Setup Find Fi
5. select ref transponder Movement style Move left right Quality AA 0 Strength AAA 0 Store sat position Expert motor settings gt Select Satellite Press the lt or button to choose the Satellite name 17 ENG SCM6000 gt Edit Select ref Transponder Press lt or button to choose the TP Motor Position Press lt or button to choose the Motor positon at the off 1 64 Movement style Press lt or button to choose he movement style at the gt Step Continuous 1 second gt Move left Right Press lt or gt button to choose move left or right gt 2F1 To store sat positon gt F2 To Expert motor settings gt Select the point Satellites Setup and press the OK button Satellite Setup A Name Orb pos Deg West east F1 Dish Setup F2 Add F3 Remove Find Finder ANGLE Calculation Scan Scan Figure 6 Satellites Setup gt Select Satellite Satellite select gt Name Satellite name gt Orb pos Deg Satellite Degree West East control the antenna trun toWest or East gt F1 press F1 to enter the Dish setup menu 2F2 Add the new satellite gt F3 Remove this satellite Finder To enter the Finder menu ANGLE Calculation the satellite Degree Scan Scan this satellite program gt Press the Channel Scan button to enter the channel scan menu 18 ENG SCM6000 Channel Scan 100014 Scan method NIT Search Kind of service TV radio Quality Strength F1 Scan gt In
6. 4 or button to choose the Save screen capture to usb gt Digital audio output Press or button to choose the Digital audio out put at PCM Original Lip sync mode Press or button to choose the Lip sync mode at Auto Manual gt Audio delay Press lt or button to choose the Audio delay at Oms 20ms 40ms 22 ENG Disposal Attention Never throw the receiver and the batteries in normal household waste They may contain toxic agents that are hazardous to health and environment Therefore dispose of the device and the batteries immediately according to the prevailing statutory regulations Never throw the batteries in normal household waste x a Figure 16 WEEE Symbol Used devices contain valuable materials that should be recycled Electronic equipment is not household waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 27th January 2003 on used electrical and electronic equipment it must be disposed of properly At the end of its service life take this unit for disposal at a relevant official collection point Help to keep our environment clean which we are living in Technical specifications S2 LNB Tuner input F type connector Frequency range Input level LNB power supply LNB control signal DiSEqC control Demodulator Front end modul symbol rate SCPC und MCPC Spectral inversion C Tuner input F type connector
7. FULL HD Combo Finder Meter SCM 6000 HD DVB S2 2 DVB C Meter User manual SCM6000 Table of Contents E A cauenssucs OE ses ennasassesuss cuaseasececeacoeens 3 Safety INS UFUCUIONS PODRAS Saa 3 A A 3 General mOra O ae iciceiicia 4 Appropriate USAGE uoe aE o TAE EEN EEEE OEE ESS 4 Delivery TM AA A AA a A 4 DEVICE OVEN VIEW ds 5 Start OF OPEL OM ossee aeoe a OE SiS 9 DETAN A O IA E E A E E AE E EA 8 SIUC Ol ME DEVICE id 8 ECHO LONS DAVE 8 Charone the Dalle isaac 8 SONNE OL the Dates asa 9 System selni a a T NA 9 Lanus Scpa a a eens ees eee we 11 Factory Detalles lia fa 12 PACO Fe A 10 Factory TO 10 Satelite ACIDO AAA 11 Pimdins Chane S Man loan 12 Etamesatelltte aca 12 Cable TMAIAS Gi a 13 FEindine channels Mana docenas 14 Linne CAM UN E 15 Installation ii 16 SU A O 16 DSS OD ieai r a a so elo ooh lon eased ode 16 SELLS A O A tance Err esOn 17 Channel Setup 17 DisEqc 1 2 17 USB ooo 18 File Viewer 18 Updating 18 Backup Data 18 2 JENG Anele CalCUl AO ride 21 mAV Setup
8. NU button gt Select the point system setting gt Confirm your selection using the OK button System Setup 100 INFOR Factory Default he Figure 2 System setting language Setup Press the SYSTEM button to change the menu language gt Select the point Language setup 5 Choose your desired language using the lt or P button gt After your selection press the EXIT button and follow the instructions on 9 ENG SCM6000 Language Setup jnna OSD language English First Audio Second Audio o INFO INFOR Software version 1 155 Factory Default Press the SYSTEM button to change the menu language gt Select the point Factory Default gt Press OK to make the factory setting System Setup Restore factory settings OK Save changes MENU Abort Factory reset 10 ENG SCM6000 Attention All programs and settings configured by you will be reset to delivery status Satellite finding In this menu you have the option to search for single channels or using the display for lining a satellite dish up gt Press the FIND button to display the Satellite Finding menu Finder Finder S S2 Finder 11 ENG SCM6000 Cable scan menu Scan method Kind of service Edit select channel Modulation Scan Quality Strength NO Figure 4 Satellite Finding gt Press the lt or P button to select a satellite gt Press the lt or
9. arge the battery completely see also chapter Lithium Ion battery on page 10 Load the accumulator during the first loading procedure at least 5 9 2 hours The maximum battery charging time is approximately 12 hours Switch on the Device gt Press 2 3 seconds the red power button on the meter Lithium ions battery Explosion danger Never the two poles and connect with each other Attention Storing or operating accumulator no more than 40 C Not burning or damaging accumulator Not taking accumulator to contact with water Charging the battery 2 The maximum battery charging time is approximately 12 hours A charging circuit in the measuring device provides an optimal charge of the battery The device is charged 1f it is switched off gt Turn the device off if it is not already off gt Connect the Euro main cable with the external AC adapter gt Connect the external AC adapter to the power grid gt Connect the AC adapter to the low voltage port at the bottom gt The battery is charged as soon as you connect the AC adapter to the SCM6000 meter The Power LED shows the battery status Red the battery 1s charged Green the battery is completely loaded Storing of the batteries a Storing the batteries between 0 Celsius and 40 Celsius 2 Loading the accumulator at a longer storage every two weeks to avoid a depth discharge System setting gt Press the ME
10. better The BER value behind 10E is important The higher the better The value should be minimal 10E 4 The optimum is gt 10E 6 Installation Satellite setting gt Press the MENU button to display the main menu gt Press the A or Y button to move the cursor gt Select the point INSTALLATION and press the OK button Installation 100 14 Satellite Setup NS Channel Scan Figure 5 Satellite setup gt Select the point Dish Setup and press the OK button 16 JENG SCM6000 Dish Setup Transponder LNB Type LNB Power DiSEqC 1 0 DiSEqC 1 2 Quality CAEN 0 Strength N 0 F1 Satellite Setup Find Finder ANGLE Calculation Scan Scan Figure 9 Dish set up settings gt Press the A or Y button to move to the desired item gt Press the lt or gt button to modify the value of the selected item Use the NUMERIC buttons 1f necessary gt Select Satellite Satellite selection gt LNB Type Univ LNB1 9750 10600 Univ LNB2 9750 10750 UNICABLE 5150 9750 10750 11300 10700 22K AUTO ON OFF gt ENB power LNB Tension Off Auto 13V 18V gt DiSEqC Level DiSEqC 1 0 gt DiSEgC 1 0 Switch Input 1 2 3 4 DiSEqC 1 2 To enter the DisEqc1 2 Menu SCAN you can scan the channels at this menu by press SCAN key gt Finder To enter the finder menu gt ANGLE To enter the Angle menu gt Press F2 to enter the DiSEqC1 2 menu Distde rss 100 Select satellite Edit
11. ect this port to the satellite atn cable RF IN Connect this port to the C cable USB Connect the USB disk DC 14V Power supply port CVBS Connect this port to TV S CVBS via AV cable Ethernet Connect this port to Internet cable HDMI Connect this port to TV HDMI port via HDMI cable E lt z p SCM 6000 POWER LOCK 18V SPEAKER SPEAKER Figure Front of the meter 1 LNBI IN Digital satellite signal input LNB2 IN 2 LC Display Display of the TV picture the menu and the measured values 3 POWER LED Display of the energy state Operation red the measuring devise is switched on Off the measuring devise is switched off In charge Green The battery is charged Red The battery 1s full charged 4 LOCK LED LED lights when a signal is received 5 FUNCTION keys Shortcut key shortcut key shortcut key shortcut key 5 1 22K 13V 18V L Lights if 22K 13V 18V signals are received EDs Navigation through menus Navigation cross switching programs A V volume control lt gt OK button confirmation of a selection OK Direct enter of numbers a satellite antenna 0 i i Display current AV setup 5 15 Switch off the power Switch the TV or Radio program display 17 SPTRUM Display the menu of spectrum for spectrum meter only ON Hi ON ON Start of operation Battery Before the first operation with the measuring device ch
12. gt button to select a LNB type gt Input the Frequency using the NUMERIC buttons press lt or first then input the number you want gt Input the symbol rate using the NUMERIC buttons press or gt first then input the number you want gt Press the lt or P button to select the polarisation gt Fl button to enter the Dish Setup menu gt F2 button to add new TP gt F3 button to Remove TP Scan button to enter the channel scan menu Lining satellite aerial up gt Press the FIND button to display the menu satellite finding gt Choose a satellite gt Turn the receiving dish as long as the LOCK LED lights or the joists of the signal level and signal quality are green Once a signal is found the bar graph shows the signal strength and quality In addition C N FEC and a BER MER are displayed In addition an acoustic signal is represented 12 JENG Notice The satellite call sign see Figure 4 registers which satellite you receive at the moment At some satellites as for example T rksat a wrong satellite call sign is cosent on single transponders hence the announcement can be falsified Therefore we recommend to leave the setting on the preset first transponder with the search of a satellite Therefore the right satellite call sign is indicated in general always 5 Set up the satellite antenna exactly to receive the best signal Notice The C N value should amount 6dB at leas
13. nd Figure 11 Angle Calculation gt Press the A or Y button to select the following points Satellite e Longitude e Location e Latitude Hemisphere e Angle calculation 21 JENG SCM6000 gt Satellite Select the desired satellite Longtitude Input your local longtitude gt Location Input the direction gt Latitude Input your local latitude Longitude Input your local longtude gt After the completion of all values select Angle Calculation and press the OK button SAzimuth shows the azimuth of the chosen satellite Elevation shows the angle of elevation of the chosen satellite gt Polarity shows the polarity angle of the chosen satellite AV Setup gt Press the SYSTEM BUTTON to enter the AV Setup AV Setup 100 Display format HDMI signal SDTV standard Screen capture Save screen capture to Digital audio output Lip sync mode Display format Press or button to choose the display format at 4 3 16 9 Scaling method Press or button to choose the Scaling method at Pillar Letterbox Fullscreen zoom Fullscreen CCO Let TV scale HDMI signal Press lt or gt button to choose the HDMI signal at 18081 720p 480 5761 480 576p SDTV standardt Press or button to choose theSDTV standard at PAL NTSC SECAM PAL M PAL N PAL N Argent gt Screen capture Press or P button to choose the Screen capture at Video only Video OSD gt Save screen capture to Press lt
14. only be operated with the supplied AC adapter at the mains Do not open the meter or the included AC adapter There is danger of life through electric shock Wrong usage of the ports can lead to the destruction of the measuring device Proceed carefully with the measuring device _ Avoid low temperatures below 0 C or to high humidity _ The TFT display can be damaged by mechanical impacts _ Avoid excessive input voltages Do not operate with the device _if it has visible damage _if there are loose parts in the device _1f the device was located outdoors or in damp rooms a extended period of time Appropriate Usage The measuring device meter was developed to measure signals of digital satellite antennas and satellite systems It is exclusively for this purpose and should only be used for this purpose Use the equipment only for the purpose which is described in this manual Follow all information in this manual particularly the safety instructions on page 4 Any other usage is rated as not properly and can result in damage or even injury There will be no liability for damages caused by a non intended use Delivery range Please check if the delivery is complete Included in delivery Tool case device meter a carrying bag an extern charger an power cable AV cable F connnector an user manual CD If the delivery should be incomplete contact your specialist dealer Device Overview LNB IN Conn
15. t Values of 10dB and more are urgently if you liked to have a certain bad weather reserve Or in gt the case 1f the signal about a multicounter should be distributed to 2 several buyers The higher the C N value the better The BER value behind 10E is important The higher the better The value should be minimal 10E 4 The optimum is gt 10E 6 Cable Finding In this menu you have the option to search for single channels or using the display for lining a C antenna up Press the Menu to choice CFinder button pic to display the C Finding menu SCM6000 Finder Finder S S2 Finder O S Figure 5 C Finder munu Finding channels manual gt Press the C Finder button to display the menu C finding Cable scan menu Scan method Kind of service Edit select channel Modulation Scan Quality Strength F1 INFO Figure 6 C Finding Press the lt or gt button to select Scan method at Manual Auto gt Press the lt or gt button to select Kind of service at All services Only free services Only encrypted services gt Press the or gt or 0 9 NUMBERIC button to select Select channel frequency at 177 5MHz 858MHz 14 ENG Press the lt or gt button to choose Modulation at 16QAM 32QAM 64QAM 128 QAM 256QAM gt Press the F1 button to display C signal info Information 850000 KHZ CN 1 351 dB SNR 29 156 dB PowerLevel 30 dB BER 0 0E 08 Prev idx gt
Download Pdf Manuals
Related Search