Home

DeeGreen User Guide

image

Contents

1. marked part of the product may heat up dangerously Certifications CE CHL DeeGreen User Guide In order to avoid interruption of the print task due to an ESD event the DeeGreen M3D0100 3D printer should not be touched during the printing process If an ESD occurs the printer will restart After this situation it is recommended to use the parking position button 15 21 Information to user Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 15 105 Information to user NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation be
2. accordance with this User Guide E All malfunctions and flaws caused by the manufacturing process or the assembly are covered by the manufacturer within the limits of the warranty P The rightful printer owner is eligible for free repair should there be a Flaw within the manufacturer s responsibilities Flaws will be Fixed within 30 days from the day the Flaw is reported The warranty does not cover malfunctions and or interruptions caused by gt Usage of other than recommended filaments E Installation in contradiction with this User Guide valid laws and norms P Operation in inappropriate climate conditions E Inappropriate use The user is obliged to pay for the work of and removal by technician s costs in case of an incorrect fault report or request to P Fix a flaw caused by a user gt Unauthorized alterations to the printer P Checking and cleaning the printer P Repairs caused by power supply blackouts The warranty is void when P The printer build is altered Instructions stated in this User Guide were ignored Other than recommended filaments were used Printer electronics were interfered with TFF F The user owner has financial commitments to the seller or manufacturer F The printer was damaged due to inappropriate usage or due to inadequate movement during transportation or keeping the printer in wrong climate conditions especially inappropriate temperature and humidity J DeeGreen User Guid
3. and nozzle Be extra cautious when removing the filament from the extruder as it is hot and may cause injury Nozzle changing E Using touch screen remove filament from the printer IF the filament is already removed use same process to let nozzle heat up It is easier to change the nozzle while it is heated but mind you do not burn yourself Turn off the printer and pull the plug out of socket Using the wrench tool from accessory box unscrew the nozzle Put the pike of screw which is included with the wrench into the tube placed above the nozzle Turn the screw until you grab the tube and pull it out Then wait about 15minutes to let the heated part of print head cool down 14 DeeGreen User Guide P Using your finger place new tube to same position as removed old one then put and screw the new nozzle same way as you removed it E After that setting the offset setting is necessary Offset setting Offset is the distance between the nozzle and the print bed b This is what the model should look like when the offset is set correctly The surface is even and smooth 1 2 ke Er K 2 S i Sep i L ES ete 1 T Gr eech A yt Sh ae Rr AS WH Nk IF there are gaps between lines in one layer the offset is too high On the printer display go to Settings Other Settings Set Offset Reload to see the current value To adjust the settings press the minu
4. the last 5 cm of the string 9 DeeGreen User Guide 5 6 Hang the spool on the spool holder Do not let go of the end of the string Freed Now Follow the Filament installation chapter Filament installation 1 GA AE lg 9 Push the string end through the small box on the back of the spool chamber until it cannot go any further You should use roughly 50 cm of the string to reach the print head Use the touch screen on the Front of the printer to manage the Filament loading Go to Settings in the Main menu Choose Filament change Wait until the nozzle warms up and press Continue Select Feed in and press Continue and gently push the string in until you notice that the extruder pulls it itself Wait to see if the nozzle extrudes the Filament IF it does not press the Repeat button Clean the nozzle of the extruded plastic MIND THE NOZZLE IS HOT Now Follow the Beginning printing chapter Beginning printing 1 oa E Check the SD card is plugged in the SD card slot on the Front of the printer Check the print chamber door and top lid are closed Press the Print button in Main menu Choose a print task you would like to print Press the Print button Wait until the printer prints the first layer check everything worked After printing 1 Gently remove the glass print bed with the printout from the printer Use the spatula to remove the printout from the glass Take care of the sharp
5. Installation and service instructions warranty terms amp conditions DeeGreen User Guide N FF be3D Version 2 4 DeeGreen User Guide DeeGreen User Guide 1 Contents Mig COTO IV CS eege et le tele Bn EE 4 3 Safety gd Te d Le CN 4 o BR Ge eene e 6 Ba Pa PESO SCID OP EE 7 6 Getting the printer ready For operation vu EE 9 Ts PUMVGO FCT SCM SINS oases cae sesge cars E E E AEE E 11 8 Cleaning and SUD e e e WEN 11 9 Filaments and spare parts 11 10 Warranty terms and conditions 11 11 Authorized s rviciNg e nee Pe ordii 13 PE ee ee EE 17 DeeGreen User Guide 2 3 Safety instructions Warranty void if damaged due to not Following the instructions in this User Guide 1 None of the printer components or accessories are suitable for eating Avoid eating anything delivered From be3D 2 Spatula which is part of the accessory box is sharp Beware of cuts Mind the top lid limit switch Its edges are sharp Beware of cuts 4 Damage caused by improper use in contradiction with this User Guide or by violating the security instructions is Full responsibility of the user 5 This device is not suitable For children and must be operated by persons over the age of 18 in all other instances supervision of an adult is required The device must not be left unattended whilst in operation Some parts of the printer operate at temperatures greater than 70 C Danger of burns A
6. e E 11 The warranty is void when the printer s electronics and control units are damaged due to atmospheric events such as a thunderstorm a power network surge pollution and damage of a mechanical chemical or heat character as well as repairs alternations or modifications by an unauthorized service center or user Authorized servicing Authorized servicing is allowed only when it complies exactly with either the instructions provided in this part of the User Guide or with spare parts if received Placing a new filament string a RK RK Release the string Following the instructions on the printer screen Remove the released string manually Cut off the string end and straighten the last 5 cm 2 inches The string must be straight Put the string into the input hole 1 gg Printing String Push the string gently through the black limit switch Apply a little Force if necessary Pull the string through the transparent tube into the nozzle Check visually remove the top lid Finish the procedure Following the instructions on the printer screen until the part when the automatic rolling is initiated push the string gently towards the printer until it is rolled on automatically Repeat the process if required 13 DeeGreen User Guide E Visually check if the string is pulled in and complete the guide until the melted filament is released off the nozzle Remove the released filament from the print bed
7. edge of the spatula Mind your hands Before the next printing scrape the glass bed with the spatula to achieve a Flat surface of the glass without any bumps 10 DeeGreen User Guide 7 Printer menu scheme Filament change dn iY i Pi Parking settings position 7 Language Print Temperature Motion test Information Shutdown a Other settings Change offset 8 Cleaning and support Keep the print area clean and free of Filament remnants Clean the print area after every print task 9 Filaments and spare parts Filaments and selected spare parts can be ordered at your supplier or via distributors of be3D printers 10 Warranty terms and conditions DeeGreen 3D printer warranty Defect product liability law The law is in accordance with the latest Czech laws regarding product defect responsibility The quality warranty is not covered by this law Mechanical parts are covered by the warranty For a term of 12 months From purchase This warranty covers any unintended mechanical Failures or malfunctions caused by either manufacturing procedures or Flaws that might have occurred during the assembly procedure The warranty does not cover misuse or inappropriate usage inadequate manipulation usage and installation in conflict with this User Guide 11 DeeGreen User Guide Terms amp conditions P The manufacturer is responsible for both the device and delivered software to operate properly all in
8. he bottom to take it out Pull the printer out very carefully and put it ona solid surface e g a desk Remove the plastic using your hands only Avoid using scissors or any other sharp items Take the top lid off Carefully remove the protective Foam Cover the printer with the top lid and make sure that the lid Fits Open the spool chamber side door and take out the foam Hold the box with both hands and take it out Mind your fingers 10 Check the accessories 11 Now Follow the print preparation chapter Print preparation 1 a Place the spool holder inside the filament chamber Unpack the glass print bed Use the glue stick to make a thin even layer on the glass print bed Then make another one in a different direction and allow it to dry for a couple of minutes Check if the final layer is straight without any bumps If not wash and follow this step again Put the bed into the printing chamber The three magnets have to Fit together with the three pins on the table inside the chamber Check if the bed is immovable Connect the printer with a power source Turn on the printer Now Follow the Preparing your filament chapter Preparing your filament Unpack the spool of filament Find the end of the plastic string and release it from the holes Hold the string at all times Cut off the string s end using either scissors or a knife at under a 45 degree angle Do not allow the string to go loose Straighten up
9. s button as many times as necessary Do not forget 15 DeeGreen User Guide gt to save the value when you are done by clicking the Save button Then run the print IF the print bed hits the nozzle or if the layer is too thin and wavy the offset is too low On the printer display go to Settings Other Settings Set Offset Reload to see the current value To adjust the settings press the plus button as many times as necessary Do not forget to save the value when you are done by clicking the Save button Then run the print IF everything looks like the picture in paragraph 1 you have set the offset correctly 16 DeeGreen User Guide 12 Contact details Manufacturer be3D s r o ID No 49356593 VAT No CZ49356593 Contact address Pod Hajkem 406 1a Prague 8 180 00 Czech Republic Invoicing address Pod Hajkem 406 1a Prague 8 180 00 Czech Republic Email help be3d cz info be3d cz Web www be3d cz Changes and print errors rights are reserved Be
10. tween the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 4 Package contents P 3D printer DeeGreen Box with accessories Power supply 24 V 5 A USB cable Printing material holder Spatula for print bed cleaning and model removal Glue stick for print bed CD with DeeControl software User Manual DeeControl User Guide DeeGreen i Set of 2 nozzles and nozzle tubes with service tool SD card plugged into the printer slot Speed Manual on the top of the printer Power supply cable See ae Ss SS DeeGreen User Guide 5 Parts description Touchscreen SD card socket Space for printing material Main door to the printing area DeeGreen User Guide Printing Head Nozzle Print bed Touchscreen SD card socket Ee SD card a Power connector i a ae USB connector O ON OFF Switch DeeGreen User Guide 6 Getting the printer ready for operation Unboxing T Ge EE 9 Make sure the printer is standing on a solid platform and is not upside down Stand the printer so the protective Foam can be accessed Remove the protection Take the printer out of the box Use extra caution while doing so First stand in Front of the box and bend down at your knees Keep your back straight Grab the printer from both sides at t
11. void any contact with hot parts 8 Disabled people not able to Fully operate the device must be supervised by a technically qualified person 9 Make sure the product is complete before use 10 Danger of electric shock if not operated correctly Technical parameters 150 x 150 x 150 mm Touchscreen 4 DeeGreen User Guide 11 The printer is a heavy device In order to avoid injury or damage to the printer do not let it Fall 12 Disposal of the device must be performed in accordance with correct environmental directions 13 Keep the printer away from any Flammable substances 14 Install the printer in a place that is P Dryand free from dust E A stable environment temperature humidity E Well ventilated P Close to an easily accessible electrical supply E Atasufficient distance from objects that could cover the ventilation shafts of the printer E Ata sufficient distance from objects susceptible to heat e g curtains and drapery also From splash able liquids and organic gases e g ammonia P Outof direct sunlight E Without sudden temperature changes gt Ata sufficient distance from heating vents ventilation and air conditioning systems Attentions VN Danger Read the instruction manual Before any manipulation except of print task and print preparation pull the plug out of socket The device contains moving parts it may cause crushing and capturing Warning of hot surfaces

Download Pdf Manuals

image

Related Search

Related Contents

Manuel d`utilisation Français SART  Page 1 Page 2 田植機重要安全ポイ ント ー. ほ場まで移動するときは    「iV ハードディスクレコーダー」を新発売  mode d`emploi - Gt  0504-sman-d-4454-v1... - GeBE Elektronik und Feinwerktechnik  CrossWords User Manual  - Normfall GmbH  Manual de instrucciones y de instalación    

Copyright © All rights reserved.
Failed to retrieve file