Renesas HS2238RECB62H datasheet: pdf
Contents
1. SYSTEM INTERFACE CABLE OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS USER SYSTEM INTERFACE CABLE IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE USER SYSTEM INTERFACE CABLE RENESAS State Law Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Renesas shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the user system interface cable without Renesas s prior written consent or any problems caused by the user system All Rights Reserved This user s manual and user system interface cable are copyrighted and all rights are reserved by Renesas No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Renesas s prior written consent Other Important Things to Keep in Mind 1 Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Renesas s2. these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corporation for further details on these materials or the products contained therein Preface Thank you for purchasing this user system interface cable HS2238RECB62H for the Renesas s original microcomputer H8S 2238R group The HS2238RECB62H is a user system interface cable that connects an H8S 2633 group E6000 emulator HS2633REPI61H HS2633EPI61H hereinafter referred to as the emulator to the IC socket for a BP 112 package for the H8S 2238R group MCU on the user system RENESAS Contents Section L Configuration cc cncssreesceicds cevgeetebagiticanantdeuctenide Ae EEEE E EEEE 1 Section 2 Connection Procedures vii sicessduaiesWaprhindionpadssscepnicancendue satpendvadeenseindunnes 3 2 1 Connecting User System Interface Cable to Emulator Station seseeeeeeeeeeseeeereerreereeeeeee 3 2 2 Connecting User System Interface Cable to User System sessesesreeerrererererrererrrrererreree 5 2 2 1 Soldering the IC Socket eee eeeescesseeseessecssecnsecneecseecoesenssensesssesseessesseessees 5 22 2 Insertinp Cable Head ivitecscscesetstgcci
3. 6000 Emulator User s Manual 2PENESAS Renesas Technology Corp 2 6 2 Ote machi Chiyoda ku Tokyo 100 0004 Japan REJ11JXXXX XXXXX
4. IMPORTANT INFORMATION READ FIRST e READ this user s manual before using this user system interface cable e KEEP the user s manual handy for future reference Do not attempt to use the user system interface cable until you fully understand its mechanism User System Interface Cable Throughout this document the term user system interface cable shall be defined as the following product produced only by Renesas Technology Corp excluding all subsidiary products e User system interface cable HS2238RECB62H The user system or a host computer is not included in this definition Purpose of the User System Interface Cable This user system interface cable is for connecting the emulator station and user system This user system interface cable must only be used for the above purpose Improvement Policy Renesas Technology Corp including its subsidiaries hereafter collectively referred to as Renesas pursues a policy of continuing improvement in design performance functions and safety of the user system interface cable Renesas reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice Target User of the User System Interface Cable This user system interface cable should only be used by those who have carefully read and thoroughly understood the information and restrictions contained in the user s manual Do not attempt to use the user system int
5. UTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information lt RENESAS A WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance 2 Always switch OFF the E6000 emulator and user system before connecting or disconnecting any CABLES or PARTS 3 Always before connecting any CABLES make sure that pin 1 on both sides are correctly aligned RENESAS CENESAS H8S 2238R Group BP 112 ser System Interface Cable HS2238RECB62H for E6000 Emulator User s Manual H8S 2238R E6000 HS2238RECB62HE H8S Family H8S 2200 Series Rev 1 00 Renesas Technology 2003 6 3 www renesas com Cautions Keep safety first in your circuit designs 1 Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire
6. cosepcusrtutescasesepsnsensteanssvscesuidacedersspeostestecetieueerets 8 2 2 3 Bastening Cable Head srssiiissstecscitice tai decttei cee eE E NEE 9 224 Pastening Cable BOY s t ccsccccrssesecivsnscesesascctecsicesncsescesccssseesucsccensssuessostneesnbotaenpens 11 2 3 Recommended Dimensions for User System Mount Pad eee eeeseceeeeecneeeeeeseeeeeeetaees 12 2 4 Dimensions for User System Interface Cable Head ee eeeeeeseeceeseceeeeecneeeeeeseeeseaeeaees 13 2 5 Resulting Dimensions after Connecting User System Interface Cable eee eee 14 Section 3 Installing the MCU to the User System eee eeeeeeeeeteeeneetees 15 Section 4 Verifying O Per ain sc cecccaseemnanacessaeseieatnidoassnnndaaadenanniaentearanenaceeae 17 SECOM NOUCE oresstacesbeeonspneaseonnntnengnetiaretoeorssennrtevenrtzonceanie cena E 18 ji RENESAS Section Configuration CAUTION Use an CSPACK112A1110H02 socket socket manufactured by Tokyo Eletech Corporation for the BP 112 package IC socket on the user system Figure shows the configuration of the HS2238RECB62H user system interface cable for the BP 112 package To emulator station Screws M1 6 x 8 mm for fastening cable head qj z Z h CSB gt Cable head i EEE a i i lt gt Spacer IC socket EON KOP Cover A User system Figure 1 HS2238RECB62H User System Interface Cable RENESAS Table 1 lists the HS2238RECB62H components Please make sure y
7. cribed here may contain technical inaccuracies or typographical errors Renesas Technology Corporation assumes no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corporation by various means including the Renesas Technology Corporation Semiconductor home page http www renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corporation assumes no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in whole or in part these materials If
8. efore inserting Align pin 1 on the IC socket for an BP 112 package on the user system with pin 1 on the user system interface cable head and insert the user system interface cable head into the IC socket on the user system as shown in figure 3 manufactured by User system Tokyo Eletech Corporation Figure 3 Connecting User System Interface Cable to User System RENESAS 2 2 3 Fastening Cable Head CAUTION 1 Use the screwdriver whose head matches the screw head 2 The tightening torque must be 0 054 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder 3 If the emulator does not operate correctly cracks might have occurred in the solder The user system interface cable HS2238RECB62H head and the IC socket for the BP 112 package on the user system have no pin dedicated for alignment Use the follow procedure to fasten the cable head 1 Insert two screws M1 6 x 8 mm to and and screw it a little so that holes at and match respectively Figure 4 Fastening Cable Head Procedure 1 RENESAS 2 Next fasten screws to and a little so that four screw holes are ali
9. erface cable until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the user system interface cable RENESAS LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and or workmanship Renesas will repair or replace any user system interface cables determined to be defective in material and or workmanship User system interface cables are wearing parts which Renesas will not repair or replace if damaged and or worn through use The foregoing shall constitute the sole remedy for any breach of Renesas s warranty This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the user system interface cable from you Renesas is not liable for any claim made by a third party or made by you for a third party DISCLAIMER RENESAS MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL RENESAS BE LIABLE FOR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE USER SYSTEM INTERFACE CABLE THE USE OF ANY USER
10. gned Then each screw should be tightened a little at a time alternating between screws on opposing corners Figure 5 Fastening Cable Head Procedure 2 RENESAS 2 2 4 Fastening Cable Body Connect the cable body to the cable head Removing Push the remove jig Cable head User system Figure 6 Fastening Cable Body RENESAS 2 3 Recommended Dimensions for User System Mount Pad Figure 7 shows the recommended dimensions for the mount pad footprint for the user system with an IC socket for an BP 112 package CSPACK112A1110H02 socket manufactured by Tokyo Eletech Corporation Note that the dimensions in figure 7 are somewhat different from those of the actual chip s mount pad 112 4 0 05 RA EE EHS Ge oe EEEN p abi p EEE RER E DOOM ee A ek CGO OSS Oe DADOOSHHOHDD 4 01 3 0 05 Unit mm Through hole Figure 7 Recommended Dimensions for Mount Pad 12 RENESAS 2 4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 8 63 5 63 5 Unit mm Tolerance 0 5 mm Figure 8 Dimensions for User System Interface Cable Head RENESAS 25 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions after connecting the user system interface cable head to the user system are sho
11. n should be made a little tighter alternating between screws on opposing corners Use the screwdriver provided with the package The torque in tightening must be 0 054 Nem or less When removing the cover from the IC socket hold the side of the cover so that no stress is applied to the soldered connections between the IC socket and user system while the screws on the cover are being unscrewed Use tweezers to remove the MCU from the opening in the spacer RENESAS Screws M1 6 x 8 mm Pin 1 CSPACK112A1110H02 manufactured by User system Tokyo Eletech Corporation Figure 10 Installing MCU to User System 16 RENESAS Section 4 Verifying Operation 1 When using the E6000 emulator for the H8S 2633 series turn on the emulator according to the procedures described in the H8S 2633 E6000 Emulator User s Manual HS2633REPI61HE 2 Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins with the MEMORY_FILL command emulator command If an error is detected recheck the soldered IC socket and the location of pin 1 3 The emulator connected to this user system interface cable supports two kinds of clock sources as the MCU clock an emulator internal clock and an external clock on the user system For details refer to the H8S 2633 E6000 Emulator User s Manual HS2633REPI61 HE To use the emulator internal clock Select the clock in the emulat
12. n is opened After the package s seal has been broken store the socket in a desiccator Do not touch the solder balls If they are touched solder may not adhere to the solder surface The IC socket is covered by a protective cover Socket and cover are fastened together by four screws before the whole is vacuum packed to prevent bending of the IC socket s pins To avoid the scattering dispersal of flux from other components to the IC socket keep the protective cover on the IC socket until solder reflow has been completed 3 Install the provided guide pins into the holes for the guide pins on the user system Check that the pads are correctly aligned with the IC socket RENESAS 4 Notes on soldering the IC socket a The IC socket is larger than the actual IC package therefore refer to figure 7 for the installation of other components b Do not install components that occupy large volume close to the IC socket Such components will prevent the convective flow of heat during reflow c a Since the IC socket has a greater volume than the IC package it is recommended that the temperature profile under the conditions used in installation be measured by attaching a temperature sensor to the back side of the IC socket d wm Under the reflow conditions for soldering the IC socket specify the actual heating to more than 210 C for 30 to 60 seconds Recommended Reflow Conditions Surface temperature of IC socket connec
13. or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials 1 These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corporation product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights belonging to Renesas Technology Corporation or a third party Renesas Technology Corporation assumes no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these materials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corporation without notice due to product improvements or other reasons It is therefore recommended that customers contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor for the latest product information before purchasing a product listed herein The information des
14. or station with the CLOCK option in the Configuration Properties dialog box To use the external clock on the user system Select external clock target or target 2 with the CLOCK option in the Configuration Properties dialog box and supply the external clock from the user system to the emulator Supply the external clock to the system clock by inputting the external clock from the EXTAL terminal on the cable head or connecting a crystal oscillator to the EXTAL and XTAL terminals To supply the external clock to the subclock connect the 32 768 kHz crystal oscillator to the OSC1 and OSC2 terminals The user system interface cable has the oscillator circuits shown in figure 11 For details refer to section 22 Clock Pulse Generator in the H8S 2238R Series H8S 2237 Series Hardware Manual R11MQ HCU04 R5 3 3 MQ R13 10 kQ To E6000 RIER EKO To E6000 lati emulator A HCU04 HCU04 OSC1 OSC2 EXTAL XTAL System clock oscillator Subclock oscillator Figure 11 Oscillator Circuit 17 RENESAS Section 5 Notice 1 Make sure that pin on the user system IC socket is correctly aligned with pin on the cable head before inserting the cable head into the user system IC socket 2 The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU 3 This user system in
15. ou have all of these components when unpacking Table 1 HS2238RECB62H Components No Component Quantity Remarks 1 Cable body 1 Includes flat cable 2 Cable head 1 3 IC socket 1 For the BP 112 package 4 Spacer 1 For installing an BP 112 packaged MCU 5 Cover 1 For installing an BP 112 packaged MCU 6 Screws M1 6 x 8 mm 4 For fastening cable head and for installing an BP 112 packaged MCU 7 Driver 1 Dedicated screwdriver to fasten the screws Documentation 1 User s manual for HS2238RECB62H this manual 2 RENESAS Section 2 Connection Procedures 2 1 Connecting User System Interface Cable to Emulator Station AWARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned The user system interface cable dedicated to the emulator must be used To connect the cable body to the emulator station follow the instructions below 1 Make sure the user system and emulator station are turned off CAUTION When connecting or removing the user system interface cable apply force only in the direction suitable for connection or rem
16. oval while making sure not to bend or twist the cable or connectors Otherwise the connectors will be damaged 2 After making sure the direction of the cable body connector is correct firmly insert the cable body connector into the emulator station socket figure 2 RENESAS Emulator station Figure 2 Connecting User System Interface Cable to Emulator Station RENESAS 2 2 Connecting User System Interface Cable to User System A WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable head to the user system follow the instructions below 2 2 1 Soldering the IC Socket Install the socket for BP 112 packaged ICs on the user system 1 Gently apply solder to the BGA pads of the user system Be careful to keep the thickness of the solder within 100 to 150 um Too much solder will cause short circuiting of the pins 2 The IC socket is vacuum packed to avoid oxidization of the surfaces of the solder balls It is thus recommended that the IC socket be installed on the user system if you don s install the socket immediately after the package it comes i
17. semiconductor products Renesas assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Renesas Figures Some figures in this user s manual may show items different from your actual system Limited Anticipation of Danger Renesas cannot anticipate every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the user system interface cable are therefore not all inclusive Therefore you must use the user system interface cable safely at your own risk IIl RENESAS SAFETY PAGE READ FIRST e READ this user s manual before using this user system interface cable KEEP the user s manual handy for future reference Do not attempt to use the user system interface cable until you fully understand its mechanism DEFINITION OF SIGNAL WORDS gt This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CA
18. terface cable is specifically designed for the HS2633REPI61H HS2633EPI61H emulator Do not use this cable with any other emulator station 4 To prevent breaking of wires in the cable body do not place heavy or sharp metal objects on the user system interface cable 5 While the emulator station is connected to the user system with the user system interface cable force must not be applied to the cable head Place the emulator station user system interface cable and user system as shown in the example in figure 12 Place components so that the cable body and cable head are parallel to the user system Emulator station Cable Cable head is parallel Z t lator stati H O CT a o emulator station a Cable head is parallel to user system User system Figure 12 User System Interface Cable Location Example 6 The P1 short connector is used for testing Do not remove the short pin that is inserted in the side of pin 1 and pin 2 Figure 13 Short Connector 18 RENESAS H8S 2238R Group BP 112 User System Interface Cable HS2238RECB62hH for E6000 Emulator User s Manual Publication Date Rev 1 00 June 3 2003 Published by Sales Strategic Planning Div Renesas Technology Corp Edited by Technical Documentation amp Information Department Renesas Kodaira Semiconductor Co Ltd 2003 Renesas Technology Corp All rights reserved Printed in Japan H8S 2238R Group BP 112 User System Interface Cable HS2238RECB62H for E
19. tor Preheating 150 to 180 C for 180 seconds Actual heating To more than 210 C for 30 to 60 seconds RENESAS CAUTION Never dip the IC socket in flux or use wash to clean the IC socket This is because flux may remain inside the IC socket due to the IC socket s structure When using the IC socket with other DIP products never clean the other DIP products with flux because the flux may enter the connector through the guide pins of the IC socket When an IC socket with guide pins is soldered to the user system about 1 4 mm of the guide pins will stick out when the user system board is 1 6 mm thick When a load is applied to the guide pins from the back of the user system board stress will be applied to the soldered part of the IC socket and this may destroy the connectors Do not apply any load to the guide pins after the IC socket has been soldered on the user system When an IC socket with no guide pins is soldered to the user system the soldered part will crack if stress is applied to the IC socket Therefore always apply adhesive to the connector and the user system so that there is a firm connection between them When the IC socket has guide pins it is recommended that epoxy resin adhesive or solder be applied to the guide pins at the back of the user system to make sure that no stress is applied to the soldered part RENESAS 2 2 2 Inserting Cable Head CAUTION Check the location of pin 1 b
20. wn in figure 9 21 5 Cable head ene c 8 3 i IC socket tiene a 5 mm CSPACK112A1110H02 pa User system manufactured by Tokyo Eletech Corporation Figure 9 Resulting Dimensions after Connecting User System Interface Cable 14 RENESAS Section 3 Installing the MCU to the User System CAUTION Check the location of pin 1 before inserting Use a provided screwdriver The tightening torque must be 0 054 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the MCU does not operate correctly cracks might have occurred in the solder 1 Attach the spacer and cover to the IC socket Place the spacer on the IC socket Place the two guide pins of the spacer in the corresponding holes on the IC socket Place the MCU gently in the opening of the spacer Be sure to correctly align pin 1 of the MCU with the IC socket The solder balls of the MCU will then be in the correct locations relative to the connection pins of the IC socket Put the cover on the spacer The four holes at the four corners of the spacer and of the cover must be aligned Use the four screws to fasten the cover to the IC socket Each screw in tur
Download Pdf Manuals
Related Search