User Manual
Contents
1. z suvky Figure 7 Manual outlet control Use icon On Off for direct control of outlet power supply Icon Restart performs restart of device plugged into the outlet During restart there is a delay between power off and power on of the outlet which can be adjusted in section Section 5 1 2 General outlet settings 14 Control and configuration neTiO 230C cS All outlets can be controlled at once by means of two icons at the page bottom Depending on current outlet state it is possible either to power off or power on all outlets and also to restart them 5 1 2 General outlet settings Use panel General settings to configure various outlet related settings Outlet name serves for outlet identification and is displayed above its control icons Reset delay is a number of seconds to wait between power off and power on during outlet restart cycle Check last option to power on the outlet by default after NETIO starts up such as after power outage E x Output 1 Timer Watchdog Zi General oO Reset delay 5 Output 2 Turn on when NETIO starts Save Changes Output 3 D O q Output 4 O q Figure 8 General outlet settings Save configuration changes by clicking Save changes button 15 Control and configuration neTiO 230C cS 5 1 3 Watchdog Use 7 Watchdog function to monitor various network devices If monitored device does not respond2. Figure 10 Timer settings 17 Control and configuration n Q P ZOC CS 5 2 Device configuration Please pay attention to device configuration so that it can function properly 5 2 1 Time settings Click Date and time in the left menu The device supports three ways of time configuration Time can be set manually or synchronization with a NTP server or client s computer can be used Daylight saving time option is also available neTIO 230C5 2012 05 16 11 53 00 English A admi NETIO 230CS amp Use NTP Server Outlets server address pool ntp org Timezone GMT Western Europe Time London Lisbon Casablanca Date Time 2 Set time manually E mail Date 201 2 05 1 Network Synchronize with this computer Enable daylight saving Begin 2012 03 25 02 00 00 End 2012 10 28 02 00 00 Save Changes Serial Tunnel LIsers Firrmw are system Figure 11 Date and time configuration Save date and time settings by clicking Save changes button 18 Control and configuration n Q P ZOC CS 5 2 2 E mail configuration Click 22 E mail from left menu The setting will be used to send e mail reports from this device neTIiO 230Ccs 2012 05 16 11 55 35 230 5 SMTP server smtp example com Enable SMTP authentication Outlets Username Date Password E mail Authentication auta Network To info example com Seri
3. 0 00022 600000 00000000 en nnne 10 A MED XTE sox 12 5 Configuration of the device e I nenne enne nenne nnne 12 Oz Login 5 oa 13 7 Manual outlet control 2 0 15 5 10000000000000000000 14 8 General outlet settings ccccccsssssceccccccecseessnneeeeeceecesensssceeececesesensssseeeeeeeeceessstsseeeeeeeeseeentaes 15 9 Watchdog settings 12 2 2220 0001000000000000000000000000000 16 SEITE As Rm 17 11 Date and time configuration eI eene enne nene nennen nennen enne ns 18 E mail RE RT 19 13 Network configuration ccccccccccssscccccsssseccccsseeeccecseeeeecesseeeecessseeescesseeeeseesseeeseessseeeseesseeeeetsaaes 20 14 Serial Tunnel symbol on the front panel of the NETIO 230CS 2 15 Serial Tunnel configuration sss eene nennen nenne enne nnns 2 22 17 Detailed user permissions management 1 400 2 2 222221100000 23 18 Select file and upgrade screen emen nnne nnne 24 19 NETIO restarts after finished upgrade 25 PO EE E oom 26 nerTiO e3oc cs Preface Thank you for purchasing a KOUKAAM product To prevent incorrect installation or improper use
4. NETIO 230C CS device can be also easily integrated into your applications using commands control of the device is executed by commands in the following format http IP address cgi control cgi command amp command Replace the string IP address gt with the IP address of your device The string command is the actual command commands hash hash Sends a request for an encrypted login string The command returns lt html gt hash lt html gt login lt p c gt lt user name gt lt password gt Login to the device Use command login plain for unencrypted login For encrypted login use command login crypted Other command parameters are username and password The return values are described in chapter Section 5 3 7 Return values In case of using CGI commands the return value is enclosed in the HTML tags lt html gt a lt html gt quit quit Logout from the system The return value is lt html gt 110 BYE lt html gt This command can be used only in CGI compatible mode port lt list xxxx gt The parameter list lists the output state in the format lt html gt port port2 port3 port4 lt html gt where port to are values 0 for output off and 1 for output on The parameter xxxx is a string for setting the port Replace symbol x with O 1 u or i just as applies to port setting via Telnet All commands can be shortened to individual symbols For example the command por
5. You will be continuously notified about upgrade progress until it is finished 24 Control and configuration neTiO 23ocs5 NE TIO 23005 Firmware version Outlets New firmware bin Date Time E mail Network Serial Tunnel Llsers Firmware Figure 19 NETIO restarts after finished upgrade NnETIO 230C CS 5 2012 05 17 14 20 53 GA Eng v 4 00 Ihame gumba xnetio230B b1 rx Restarting Upgraded Login screen after restart indicates that upgrade process has successfully finished 25 Control and configuration c T Q 2 ZOC lt 5 2 7 System settings In this section you can do basic settings and view basic system parameters neTIO 230c5 3 2012 04 26 1B 230 5 Device name METIO 230CS5S MAC address 24 2 10 0 13 B4 Outlets Uptime 33 days 13 hours 12 minutes Date Time Firmware version V 4 00 Upgrade E mail Switch delay seconds Network serial Tunnel Users Firmware System Figure 20 System settings Device name Name of your device MAC address Hardware address of this device Uptime Time from last restart Firmware version Current firmware version and upgrade link Switch delay Delay between turn on of two and more outlets Restore factory defaults Reload default settings 26 Control and configuration neTiO 2e230C C5 5 3 Control of the device via Telnet or serial link 5 3 1 Encrypted login For log
6. 5 2 3 Network settings 1 1 2 0000000000000000000000000000000 20 5 2 4 Serial Tunnel 230 5 only 21 5 2 5 User account management 22 5 2 6 Firmware upgrade 1 1 1110 II r r sse enn nnne nennen nennen esee 24 SAM E iae MERE Mr 26 5 3 Control of the device via Telnet CGI or serial link 2 2 17 22009 27 5 3 1 Encrypted login mI emen 27 5 3 2 Communication via KSHELL interface 27 COl CORIO 28 5 3 4 Using kshell cgi interface to control the device 2 29 5 3 5 Communication via a serial 29 5 3 6 List of telnet kshell cgi and serial link commands 2 29 5 3 7 Return values MR LE E A 36 5 4 Manual conmo A 37 5 5 Status LED diodes 37 ECMMIFOUDICSNOONNG A EE 38 5 6 1 Forgotten password Reset to factory settings 38 5 6 2 Problem with update of firmware 38 5 6 3 Changing the fuse e eene en nnne enne nene nennen ns 38 MM S 39 nerTiO e3oc cs List of Figures 1 NETIO 230C front view cccccccceccccccccecccccuccecccccseeccccusceccccuueececuseeccceuueeececueeecesaeeecesauteseceaaeeeess 8 2 NETIO 230CS front view ccssseccccssseccccessecccccvseccccesseccccceececterssceccevsesectersedtenss c lm 9 3 NETIO 230C CS back view
7. mode dst start dst end system webport port Sets the web port of the device The default value is 80 system webport Gets the web port of the device system kshport port Sets the kshell port of the device system kshport Gets the kshell port of the device The default value is 1234 system dhcp 30 Control and configuration neTiO 2e230C C5 Gets the DHCP client parameter setting system dhcp hostname enable disable Enables sending the name of the DHCP server system dhcp enablel disable gt Enables setting the SNTP server according to the IP address set on the DHCP server system reset Restores the device to factory defaults After posting this command factory defaults is restored and system restarts system timezone lt offset gt Sets local timezone Enter the time offset in minutes system timezone Gets time offset of the local time from UTC The return value is in minutes system sntp Gets SNTP client settings system sntp enable disable sntp ip domain Sets SNTP client Enables or disables time synchronization with the SNTP server The server address can be entered as an IP address or as a domain name system dns ip Sets the IP address of the DNS server You have to restart the system using the command reboot or turn off and on your Netio for the changes to take effect system dns Gets the set address of the DNS server system swdelay delay Sets the delay betw
8. name username privileges Gets a list of user privileges in the format OCVMSNAUF the meaning of the parameters is as follows view outlet status C control outlets V view outlet settings M change outlet settings timer watchdog S view NETIO settings time e mail network change simple settings time e mail 35 Control and configuration neTIiO 230C C5 A change advanced settings network tunnel U manage users F upgrade firmware reset to factory defaults user add name privileges GUI lt passwd gt Adds new user GUI Information for GUI enter O if used via kshell passwd password user list Gets list of users in the format id lt name gt privileges GUI user delete lt gt Deletes user user passwd id old new Changes user password user update id name privileges GUI passwd Updates user settings 5 3 7 Return values 100 HELLO lt hash gt Device response after connection Hash after HELLO can be used for encrypted login 110 BYE You have been signed out 120 Rebooting Restarting 130 CONNECTION TIMEOUT Connection time out 250 OK Command was successfully executed The value returned by the called command may follow 500 INVALID VALUE Incorrectly entered value 36 Control and configuration neTiO 2e230C C5 501 INVALID PARAMETR Incorrectly entered parameter 502 UNKNOWN COMMAND Incorrectly ente
9. of equipment please carefully read these Operating Instructions and the Quick Installation Guide which is included in the package Carefully read the following notice The device you have purchased operates under a certain voltage Incorrect manipulation with the device may result in damage to the device or injury to the person handling it nerTiO e3oc cs Important notice 1 The manufacturer is not liable for potential damage caused by incorrect usage or placing the device in an unsuitable environment The device is not intended for usage outdoors Do not use the device in an environment with strong vibrations If the device malfunctions contact your vendor Unauthorised modification of this device can damage it or cause fire Prevent contact with fluids do not expose the device to high temperatures Protect the device from falling Only devices approved for use in the electricity network may be connected 0 N Oo FR C N If the device malfunctions disconnect it from the electric power supply and contact your vendor neTiO e3oc cs 1 Introduction The NETIO 230C CS is a multifunctional power supply controller This device is intended to control power supply via web interface telnet or commands Thanks to the network administration technology based on IP protocol basis the user can control or provide a power supply to a connected external device appliance via a computer connected to the LAN o
10. E mail Network serial Tunnel address Net mask Default gateway DNS server Web port Users KSHELL part Firmware 192 168 0 21 255 255 255 0 192 168 0 1 192 168 0 1 1234 Allow the discover tool to change network configuration system Save Changes Warning Changes to network settings may result in NETIO becoming unavailable at the current address See the NETIO User Manual for ways to find the NETIO at its new location Figure 13 Network configuration Save network settings by clicking Save changes button 20 Control and configuration Q P ZOC CS 5 2 4 Serial Tunnel NETIO 230CS only NETIO 230CS supports Serial Tunnel allowing control of another RS 232 device over serial line Such device should be connected to port marked with tunnel symbol on the NETIO front panel Figure 14 Serial Tunnel symbol on the front panel of the NETIO 230CS device The Serial Tunnel is available on the IP address of NETIO 230CS on port no 1235 by default This port number as well as serial port baud rate and parity settings can be changed here neTiO c3oc5 s 2010 10 27 11 43 18 Ca 230 5 Enable serial tunnel Port Baud rate 19200 Outlets Date Time Parity none E mail Replace characters with failed parity check Network Replace with CL of 3 Serial Tunnel Allow access only from subnet IP address sers Met mas
11. FF and DISCONNECTED FROM THE POWER SUPPLY Also disconnect all the devices connected to the outputs To replace the fuse unscrew the fuse holder ideally using a flat screwdriver Always replace the fuse with a new fuse of same type 250V 10 type F After insertion of the correct fuse replace the plastic holder and screw it into place Connect the power supply cable and try to switch on the device Before reconnecting all the devices to the outputs check whether the fuse was not blown by a fault on the connected devices 38 neTiO e3oc cs Conclusion The manvfacturer bears no responsibility for any technical or printing errors and reserves the right to make any changes in the product and in this user manual without prior notice Any such changes will be announced via the manufacturer s website www koukaam se The manufacturer does not provide warranties of any kind whatsoever with regard to any information given in this user manual or any derived warranties regarding product saleability or fitness for a specific purpose In particular the manufacturer does not provide any warranties for defects caused by incorrect use of the product failure to abide by the instructions and recommendations stated in the user manual and for any defects caused by unprofessional activities of third parties outside the manufacturer s authorized service shop We believe that you will be satisfied with our product In case of any questions or comments relati
12. Igi male ees FIRMWARE 4 0 Instruction manual 1 8 2012 neTiO e3oc cs Table of Contents di E 4 Important notice 2 aoea 5 6 IN 6 1 2 Specifications enne rne 1 3 Minimum system requirements 2 Equipment interface 8 2 1 Front view 230 0 8 2 2 Front view 230 5 2 9 2 3 Back view NETIO 230C CS 2 2 2 0202 0 0 00202 0 000000000000002 0000 10 1 3 1 Connection of the device nennen nennen nnne ener ee nenne 1 4 Initial configuration eee II eene RI nennen nennen eee enne nnns 12 5 Control and configuration I eene emere eene nnne eene ee 14 14 5 1 1 Manual outlet control eene 14 5 1 2 General outlet settings nemen nennen nnns 15 212 772 E edes DENIM IM NU NA MN 16 SU 17 5 2 Device configuration eee nennen eene 18 5 2 1 Time setings 18 5 2 2 E mail configuration 19
13. al Tunnel From netio230 example c Subject ALERT w Save Changes Lsers Firmw are system Send Test E mail Figure 12 E mail configuration SMIP server mailserver used to send message Enable SMTP authentication check this option if mail server requires authentication Note NETIO 230C CS does not support STARTTLS encryption To message recipient address From address that will appear as message sender Subject message subject Save e mail settings by clicking Save changes button It is possible to verify configuration by clicking Send test e mail button 19 Control and configuration nerTiO e3oc cs 5 2 3 Network settings Click Network in the left menu If there is a DHCP server available the device will automatically configure various network related parameters such as IP address network mask and gateway Check Use DHCP option to enable this behavior Use Set static IP address option to manually configure these parameters Static IP address is also required for successful firmware upgrade Please read Section 5 2 6 Firmware upgrade chapter for further details Configuration items Web port and KSHELL port sets Web and KSHELL ports Default settings are sufficient for most users a 2012 05 16 12 15 59 amp admin Fs Sign out neTIiO c23aocs English NETIO 230CS Use DHCP Outlets Get NTP server address from DHCP server amp Set static IP address Date Time
14. een turning on of two outputs Enter the value in tenths of seconds system swdelay Gets the delay between turning on of two outputs system discover enable disable Enables disables network parameter settings from the discover utility system discover Gets whether the system discover selection is enabled or disabled system eth 31 Control and configuration neTiO 2e230C C5 Gets the network interface settings in the format dhcp manual ip address masks gateway system eth dhcp manual ip address mask lt gt Sets the network interface IP address network mask and gateway are set only if the manual parameter is selected For the changes to take effect it is necessary to either restart the system with the command reboot or switch the NETIO off on Example The system command eth manual 192 168 10 150 255 255 255 0 192 168 10 1 sets the network address 192 168 10 150 network mask 255 255 255 0 and default gateway to 192 168 10 1 system network Gets network settings in the format lt webport gt lt kshport gt lt dhcpntp gt mode IP mask lt gateway gt lt DNS gt system network lt webport gt lt kshport gt lt dhcpntp gt lt mode gt lt IP gt lt mask gt lt gateway gt lt DNS gt Network settings system update Switch to the upgrade firmware mode system mac Gets MAC address of the device system reboot Reboots the device Port commands port li
15. et switch off three times in a row the output is switched off for the fourth time and remains off A warning e mail message will be sent to you each time the output is switched off port mode port num lt mode gt bez parametru mode vyp e aktu ln re im portu e s parametrem nastav re im portu port lt output gt 0 1 manual int Gets and sets output state if you enter only the number of the output without any parameter the command gets the output state O off 1 on output number with parameter 0 1 turns the output on off 34 Control and configuration neTiO 2e230C C5 output number with parameter manual switches output to manual control output number with parameter int interrupts the output Example The command port 2 1 activates output 2 E mail commands email server Gets the IP address or domain name of the SMTP server email server ip domain server address Sets the IP address or domain name of the SMTP server email message Gets e mail settings email message sender receiver subject Sets e mail settings email auth Gets settings of the SMTP authentication email auth lt enabled gt lt method gt lt username gt lt password gt Sets settings of the SMTP authentication User and privileges commands user get Gets user privileges of the currently signed user in the format lt id gt lt name gt lt privileges gt id user number 5
16. in with secure password you must first get the hash code from the device You get this either in the return code after connection via KSHELL or the CGI command hash For calculation the MD5 sum is used that has been calculated as the following sum lt name gt lt password gt lt hash gt This is a 128b number 32 characters transmitted in a hexadecimal format 5 3 2 Communication via KSHELL interface The connection procedure is shown in the following example 1 Open the window with command line 2 Enter the command telnet 192 168 10 100 1234 enter the address after the address of your device will 1234 with the port which you have set for KSHELL on the device 3 The device should list a response similar to the following 100 HELLO EB5D61F6 The last 8 characters comprise the hash string used for encrypted login 4 Now you can login with the command login name password where name is the username and password is your password If you have entered the correct username and password the device response is 250 OK You are now logged on and you can control the NETIO device using the commands from the following chapter Every communication session via KSHELL interface has limited validity In case of inactivity of approximate duration one minute the session will be terminated automatically If you need to keep the session active you can use the command noop 27 Control and configuration neTiO 2e230C C5 5 3 3 control
17. ion parameters are as follows Transmission speed 19200 baud Data format 8 1 The command format is identical to that of the commands for communication via KSHELL interface The list of commands is in the following chapter Note for communication via serial link you do not need to login as applies to communication via KSHELL interface This means that after connection of the cable you can directly enter the kshell commands to the terminal 5 3 6 List of telnet kshell cgi and serial link commands Basic commands login lt name gt password Sign in using the plain password Example Use command login admin admin to log in with username admin a password admin login lt name gt lt md5 gt Sign in using the encrytped password version Gets firware version 298 Control and configuration neTIiO 230C C5 alias Gets the device name alias lt name gt Set the device name quit Sign out In case of changes in system settings perform restart of the device reboot Sign out closes the connetion and restarts the device noop Keeps the connection alive performs no action uptime Gets the current uptime Commands For system settings system time lt YYYY MM DD HH MM SS gt Sets the local time system time Gets the local time in the formar YYYY MM DD HH MM SS system dst mode dst start dst end Sets the daylight saving settings system dst Gets the daylight saving settings in the formar
18. k Firrriw system Figure 15 Serial Tunnel configuration For increased security access to the tunnel can be limited to clients within a defined set of IP addresses To limit access enter IP address of device or computer and corresponding subnet mask 21 Control and configuration Q P ZOC CS 5 2 5 User account management If the device is used by multiple users using accounts with different privileges is advised In the left menu click amp Users menu item There are three different user types a 2012 05 17 14 06 29 GA English A adm 230 5 admin Username steve Password Outlets Create User Confirm password Date Time Privileges more O administrator full access E mail user may only control outlets Network O guest may only observe status Serial Tunnel Users Figure 16 Add user Admin user with full authorisation User user that can control the ports but cannot change system settings Guest user that does not have the rights to change any settings and can only see the current state of the ports Pick one of above options as necessary There is option of finer grained access control List of all available permissions will be available after clicking More hyperlink 22 Control and configuration neTiO 23oc5 230 5 admin Outlets Create User Date Time E mail Network serial Tunnel Users Fir
19. mware system a 2012 05 17 Username Password Confirm password NETIO 230C CS 14 09 31 GA Engish admin Sign Privileges less user gt Y Y view outlet status control outlets f view outlet settings _ change outlet settings view NETIO settings change simple settings date time e mail change advanced settings network system manage users _ upgrade firmware reset to factory defaults Figure 17 Detailed user permissions management Confirm your settings by clicking Create user button User accounts can be adjusted later in similar way 23 Control and configuration Q P ZOC CS 5 2 6 Firmware upgrade In section Firmware firmware of your device can be upgraded New versions are available at http www koukaam se showproduct php article id 1479 Warning use Chrome browser and static IP address configuration otherwise the upgrade process may fail Select file with new firmware bin extension and continue by clicking Upgrade button neTiIiO c23o0c5 2012 05 17 13 44 54 CA Englis 230 5 Firmware version v 4 00 Outlets Mew firmware bin home gumba xnetio230B b1l Browse Date Time Network Serial Tunnel 5 lt Firmware Figure 18 Select file and upgrade screen NETIO will restart several times during upgrade Do not turn it off otherwise there is threat of permanent failure
20. ng of the parameters is as follows output number of the output you are setting wd enable disable enable disable Watchdog function on the given output wd ip addr IP address of the monitored device wd timeout maximum ping timenout of the monitored device before it is restarted wd PON delay time interval in seconds in which the Watchdog function will not be active after output restart During this period the monitored device should start operating after restart ping interval interval in seconds in which queries will be sent to the device max retry maximum number of output restart attempts if the monitored device does not respond to the ping commands After expiry of the given number of attempts the output remains inactive max retry poff enableldisable enable disable max retry function send email enableldisable enable disable e mail report when the monitored device is unavailable or the value of max retry is exceeded Example The command port wd 2 enable 192 168 10 101 10 30 1 3 enable enable enables the Watchdog function on output 2 The device at the address 192 168 10 101 will be monitored The maximum response time of the monitored device will be 10 seconds The ping commands will be sent at one second intervals If the monitored device does not respond within 10 seconds output 2 is switched off for 30 seconds If the device will not respond to ping commands after s
21. ng to the functionality of the NETIO product please do not hesitate to contact us The company KOUKAAM a s represents that all products software and other third party components used in this equipment were used by the company KOUKAAM a s on the basis of the relevant consent and pursuant to licence agreements between the company KOUKAAM a s and third parties The company KOUKAAM a s reserves the right to change those licence terms and conditions as the case may be and such changes will be published in the updated version of a manual available on the website of the company KOUKAAM 5 www koukaam se The KOUKAAM Team KOUKAAM a s Kaplanova 2252 8 Prague 4 148 00 Czech Republic www koukaam se 2012 KOUKAAM a s All rights reserved 39
22. ormat set time format t 55 dt YYYY MM DD HH MM SS UX xxxxxxxx unsigned long with prefix Ox lt hex gt O lt octal gt or decimal mode once daily weekly Selection of timer mode on time time when the output will be turned on off time time when the output will be turned off week schedule a series of ones and zeros the first number represents Monday the last represents Sunday Example The command port timer 3 t weekly 08 00 00 17 30 00 1111100 switches the timer on at output 3 From Monday to Friday output 3 will always be switched on at 08 00 and switched off at 17 30 port timer output d t u Gets the timer settings in the given format for the selected port port wd output Gets Watchdogsettings of given outlet in the following format wd enable disable wd ip addr wd timeout wd PON delay ping refresh max retry max enableldisable send email enable disable port wd output wd enable gt Enables or disables Watchdog function 33 Control and configuration neTiO 230C cs5 Example The command port wd 4 enable activates the Watchdog function on output 4 port wd output wd enable disable wd addr wd timeout wd PON delay ping interval max retry max poff enable disable send email enable disable Watchdog settings command The meani
23. r Internet network No special software is necessary to control the device the Web interface is already integrated in the firmware Using the web interface you can easily control and set the entire device and individual outputs Imagine that you are travelling around the world and you can remotely or via a timer control the power supply to your electrical appliances such as computers servers routers electric gates security surveillance system or other appliances 1 1 Characteristics Integrated web server Support for a broad spectrum of browsers Internet Explorer Mozilla Firefox Opera Google Chrome Four controllable ports Four manual control buttons e Serial port for control of the device Serial tunnel version NETIO 230CS Support for SMTP SNTP DHCP DNS Telnet protocols Control using commands Possibility to login using an encrypted password User authorisation LED indication of the actual state of each port Safe anti electric shock design fire resistant materials Time control you can set the on off time for the requested port Default setting of port state after switch on and restart of the device Watchdog function for reseting frozen network device Introduction neTiO 23a0C CS E mail notification Over voltage protection on the entire device and all the four outputs 1 2 Specifications Power supply voltage 90 250 V AC Maximum switched c
24. red or unknown command 503 INVALID LOGIN Incorrectly entered username or password 504 ALREADY LOGGED IN You are already signed in 505 FORBIDDEN You are not authorised to execute the given command Sign in as user with higher privileges 506 INPUT LINE TOO LONG You have sent an input line that is too long Shorten the command and repeat the action 507 TOO MANY CONNECTIONS Maximum number of connections was exceeded Wait for someone to sign out If inactive users are signed in they will be disconnected automatically upon expiry of the time limit 5 4 Manual control Apart from control via PC the device can also be controlled using the four buttons on the front panel To switch the given output on or off press the button for two seconds If the output was off it comes on if it was on it goes off The buttons correspond to the outputs 1 4 from left to right The state of the individual ports is signaled by the green diode above the button for the given port that either switches on or off 5 5 Status LED diodes The status LED diodes on the device inform the user not only about the status of the output but also provide him with some information about the status of the system The green LED diodes provide information about the actual status of the output If diodes 1 4 are green the individual outputs are on If any of the concerned diodes is not green this specific output is off The red LED diodes inform the user about different s
25. s the device If you have a DHCP server in the network and you do not want to change the network settings you can skip the manual setting and continue to the next step The default IP address of the device is 192 168 10 100 if you do not have a DHCP server in the network If you have the device obtains an IP address automatically from the DHCP server 4 You access the web interface of the device either by entering the IP address into the Internet browser or by double clicking the IP address of the device in NETIO discover 5 The login page is displayed Enter the user name password and click the Log in button The default username is admin the password is admin neTiO e3ocs EC ME NNNM Lx Remember me Figure Login screen To login to the web interface it is necessary to have JavaScript support enabled in the browser 13 nerTiO e3oc cs 5 Control and configuration 5 1 Outlets 5 1 1 Manual outlet control In the left menu choose 22 Outlets item You will be provided with the outlet overview Each outlet is directly controlled by four associated icons All outlets at once are controlled by two icons at the bottom of the page The active icon is green the inactive icon is grey neTiO c23ocs 3 2012 05 03 230 5 Output 1 Outlets Date Time Output 2 o Network Serial E mail Output 3 Oa LIsers Firmware Syster Output 4
26. st xxxx without parameter gets the state of all ports e xxxx is a command for control of all ports simultaneously in place of x enter the commands 0 deactivate output activate output i call interruption of a given output u leave output unchanged Example The command port list Olui deactivates output 1 activates output 2 leaves output unchanged and interrupts output 4 port elist Gets port settings in the format lt name gt state wd wd ip mode wd int wd to timer mode on time off time ws 32 Control and configuration neTiO 2e230C C5 port setup output output name mod manual timer gt interrupt delay PON status Command for setting output parameters the meaning of the parameters is as follows output name Entered in quotation marks it is possible to omit the quotation marks if it does not contain whitespaces mod manual timer gt Selection of output mode PON status State after turning the device on O off 1 on Example The command port setup 1 output 1 manual 2 1 sets output 1 name of output 1 activates manual control sets the interruption time to 2 seconds and sets the status upon turning on fo on port timer output time format mode once daily weekly lt gt lt off time gt week schedule Timer settings output the number of the output that is being set time f
27. tatuses of the entire device The following states are possible Red LED 1 is on initialisation of network interface if it remains on the network is not available Red LED 2 is on posting of query to DHCP 37 Control and configuration neTiO 2e230C C5 Red LED 3 is blinking firmware update in progress Red LED 4 is on device is in firmware update mode 5 6 Troubleshooting 5 6 1 Forgotten password Reset to factory settings If you forget your password it is possible to reset to factory mode This is done by pressing and holding buttons 1 and 2 with device on Hold the buttons until the device beeps 2x During the resetting process all the LED diodes are red As soon as reset is completed the LED diodes go off 5 6 2 Problem with update of firmware If a problem arises during updating the firmware e g power failures or switching off the device before the update is completed it is possible to force putting the device into operation in firmware update mode You do this by pressing button 4 with device on Hold the button until the device beeps After this connect to the device IP address via the browser Continue to enter the firmware file as shown in the chapter which describes the firmware update process 5 6 3 Changing the fuse If the NETIO 230C CS stops working and no indication LEDs are not shining it is possible that the fuse has been blown Before actual replacement of the fuse make sure that the NETIO 230C CS IS O
28. to Ping request in a given time interval the corresponding outlet will be turned off and on The delay between power off and power is configurable It is possible to limit number of outlet restarts so that it does not happen infinitely gt Output 1 Timer p Watchdog General 07 A Enable watchdog IP address Output 2 Ping Interval 5 1 Ping Timeout s s Power on delay s Turn off permanently after resets Send e mail when device doesn t respond Output 3 4 Output 4 4 Figure 9 Watchdog settings IP address IP address of monitored device Ping timeout maximum delay between Ping request and response before it is considered unsuccesstul Start up delay Watchdog will postpone querying monitored device for this many seconds after outlet power up so that the device can fully start up Ping interval how offen will be Ping query sent to monitored device in seconds Save configuration changes by clicking Save changes button 16 Control and configuration T 1 P ZOC CS 5 1 4 Timer Timer function allows for outlet power on off at certain times It is possible to configure one time or periodic action x Output 1 Timer p Watchdog n General Y Enable timer A O Turn on once Output 2 From 1 af Mon Tue Wed Thu Fri Sat Sun Y v v v LJ m 19 00 00 23 59 39 Output 3 O af Output 4 af
29. tzlist can shortened to The commands can be joined in a string using the symbol amp Example http 192 168 200 84 cgi control cgi login p admin admin amp p 1 Oui This command executes login to the device at the address 192 168 200 84 with username admin password admin and sets the output It switches on output 1 switches off output 2 leaves output 3 in its current state and interrupts output 4 for the time set in the actual setting of the output 28 Control and configuration neTiO 230C cs5 5 3 4 Using kshell cgi interface to control the device NETIO 4 0 has a new control interface It contains both the original control tgi now control cgi and the new kshell cgi kshell cgi script Use it as follows http 192 168 1 10 cgi kshell cgi session ssid session id amp cmdz kshell command Session id is a hexadecimal number returned during the initialization of communication Kshell command is one of commands described in the table below Initialize http 192 168 1 10 cgi kshell cgi session init salt Use while communicating http 192 168 1 10 cgi kshell cgi session ssid 72b4c5f313c2133df8da6581ecA41b393 amp cmd kshell command Close http 192 168 1 10 cgi kshell cgi session close 72b4c5f313c2133df8da6581ec41b393 5 3 5 Communication via a serial link For communication with the NETIO 230C CS device via a serial link connect the device to a PC via a direct cable with Canon DB9F and DB9M connectors The communicat
30. urrent 10A Dimensions 220 x 40 x 125 mm w x h x d Network interface 1x RJ 45 10 100 Mbit s Additional interface NETIO 230C 1x CANON DB9 F RS232 NETIO 230CS 2x CANON DB9 F RS232 1 3 Minimum system requirements Computer with Internet browser Microsoft Internet Explorer Opera Mozilla Firefox with JavaScript support enabled nerTiO e3oc cs 2 Equipment interface 2 1 Front view nETIO 230C Figure 1 NETIO 230C front view 1 Four indicator LED diodes 2 Manual buttons for switching outputs on off 3 Serial port 232 4 Connector RJ 45 an interface for connection to a computer network Equipment interface neTiO 230C CS 2 2 Front view NETIO 230CS Figure 2 NETIO 230CS front view 1 Four indicator LED diodes 2 Manual buttons for switching outputs on off 3 Serial port RS232 4 Connector RJ 45 an interface for connection to a computer network 5 Serial tunnel RS232 Equipment interface neTiO 230C CS 2 3 Back view NETIO 230C C5 2 zj 907250 VAC MAXIMAL SWITCHED CURRENT 10 A Figure 3 NETIO 230C CS back view 1 Main Switch 2 Power supply 90 250 VAC 3 Fuse holder for main fuse 10A 4 Switched outlets 230V 10 nerTiO e3oc cs 3 Installation Before using the device for the first time check whether the power supply voltage setting is 90 250 V AC 3 1 Connection of the device 1 Connect the NETIO 230C CS to the computer network switches ro
31. uter using the network cable with RJ 45 conneciors 2 Connect the NETIO power supply cable to the socket 3 Connect the device which you want to control to the appropriate output 4 Switch on the NETIO 230C CS using the switch on the back of the device 11 nerTiO e3oc cs 4 Initial configuration 1 On the enclosed CD you will find the file NetioDiscover exe execute it 2 Click the button Discover This lists all the accessible NETIO devices in your network 3 Select the device from the list and click the button Device setup discover Name IP address Subnet mask Gateway MAC NETIO 230C METIO 230C 192 168 24 129 255 255 255 0 197 168 274 254 242 A420 00 00524 230 5 230 5 192 168 24 128 255 255 255 0 192 168 24 254 24 A420 002002235 Use network interface Realtek PCIe GBE Family Controller 192 168 24 141 255 255 255 255 Figure 4 Devices found The configuration window appears IP address Subnet mask and Gateway IP Address Device NETIO 230C NETIO 230C Device properties Device name NETIO 230C NETIO 230C MAC address 24 44 2C 00 00 24 IP address 192 168 24 129 Subnet mask 255 255 255 0 Gateway IP address 192 168 24 254 Figure 5 Configuration of the device 12 Initial configuration neTiO 230C C5 After editing the network configuration parameters click the button Change IP which saves the configuration and restart
Download Pdf Manuals
Related Search