HS-1500 User`s Manual
Contents
1. HS 1500 BUR Case Velalerel HS 1500 User s Manual TABLE OF CONTENTS FitPOCUCIION Aann sa anaE E E E aoe seas 1 Important Precautions D Electromagnetic Interference and Warnings 3 IdentiffeationifBerTis 0 5 Operating Your Power Chair 8g Disassembling Re assembling Your Power Chair 11 Chnarging tne Batteries srcc ererciiinenisi ae ee see seeea ase 13 Care and Wai pa 14 Troubleshooting 16 TECANICAl Specifications s e lt e lt eeqseeseeseeeceneesosereeseseeccees 18 HS 1500 User s Manual INTRODUCTION E Thank you and congratulations on purchasing your new C T M Power Chair Itis designed to provide you with transportation indoors and outdoors Chien Ti Enterprise Co Ltd is the manufacturer for the C T M mobility power chair We pride ourselves on providing safe and comfortable products Our goal is to ensure your complete satisfaction with our product We are certain that you will enjoy your C T M power chair Please read and observe all warnings and instructions given in the owner s manual before operating this power chair Also retain this booklet for future reference If you have any questions please contact your local dealer or C T M HOMECARE PRODUCT INC 6191 Schaefer Ave Suite2. Using a damp cloth helps clean the upholstery greatly Please note that using the power chair outdoors can lead to sun damage of the upholstery material Since this is a normal wear and tear condition it is not covered under the warranty SEAT BELT A damp cloth with mild soapsuds should only be used to clean the seat belts Wipe the seat belts gently removing any debris on it Do not use any chemical products to clean the seat belts as the fabric will be weakened An authorized dealer should handle all maintenance and repair of your power chair that is associated with electronics batteries motor parts and tires Here are the guidelines that can be followed by the authorized dealer FLAT SPOT for solid tires only During the storage period a flat spot may occur on solid tires Weather conditions and storage period could determine the condition of flat spots By driving the power chair 20 to 30 minutes flat spots can be eliminated 14 HS 1500 User s Manual TIRE PRESSURE for air filled tires only The condition of the tires and maintenance of the specified tire pressures not only influence tire life but also road safety to a very considerable extent Incorrect pressures are often a cause of tire problems and could resultin an accident The recommended tire pressure is 35 Ibs TIRE TREAD Inspect the tires frequently for any signs of damage unusual wear and sufficient tread depth Thread depth should not be all
3. the circuit breaker at the rear of the power chair Push it in and try the power chair again Circuit Breaker 8 When you are finished driving your power chair turn the power off before getting out Itis recommended that you lift the armrest and get out to the side for safety Caution While standing up avoiding standing on the footplate as it may cause injury 9 If you are finished riding for the day immediately recharge the batteries See CHARGING THE BATTERIES on page 13 Keep in mind these rules e Use your power chair only where it would be safe to walk e Use low speeds for reverse downhill ramps curbs or uneven surfaces Other Operating Information Hill climbing You may need to use a higher speed Fora higher speed press the right speed control switch repeatedly Down slopes To proceed down steep slopes slowly press the left speed control switch This enables driver control when the speed is setata slower motion However your power chair will not self accelerate down hills due to the automatic braking taking effect should you attempt to drive too fast 9 HS 1500 User s Manual Curb climbing Approach slowly at right angles to the curb A direct approach is needed Do not attempt curb climbing greater than a 0 9 curb Figure 12 If the Self Diagnostic Warning Lights start to flash identify the problem from the chart on page 16 and take action If the power chair breaks down and must be m
4. B Chino CA 91710 Tel 909 590 1388 Fax 909 590 3365 E Mail ctm ctmhomecare com http www ctmhomecare com or your local dealer HS 1500 User s Manual IMPORTANT PRECAUTIONS Only one person at a time can ride a C T M Power chair Maximum load is 115 kg 253 Ibs Turn off the power before getting on or off your power chair Always drive carefully with your feet on the footplate and be aware of others in your area Always use pedestrian crossings where possible Take extreme care crossing roads Do not drive on slopes exceeding 6 degrees and take extreme care when turning on slopes Do not use full power when turning sharp corners Take great care and use low speeds for backing up riding downhill over uneven surfaces and curb climbing The power chair may not operate well in high humidity Never put your power chair in neutral on slopes Follow all traffic laws when you ride in the vicinity of public roads HS 1500 User s Manual ELECTROMAGNETIC INTERFERENCE AND WARNINGS CAUTION It is very important that you read this information regarding the possible effects of Electromagnetic Interference on your power chair Powered wheelchairs and motorized scooters may be susceptible to electromagnetic interference EMI which is interfering electromagnetic energy EM emitted from sources such as radio stations TV stations amateur radio HAM transmitters two way radios and cellular phones The int
5. d Weight Capacity Ground Clearance Grade Climbable Curb Climbing Turning Radius Brake seat Width Drive Train Battery Weight Motor Size Travel Range Battery Charger Seat Type 31 9 23 6 36 8 N A 105 4 Ibs 4 mph 253 Ibs 1 6 6 degree 21 4 Electro Mechanical 18 5 2 Motor Rear Wheel Drive 23 Ibs 150W 2800 r p m 5 2 Miles 2 12V 14Ah 2A Off Board Light Weight Foldable Seat Subject to change without notice tissues
6. d below should reduce the chance of unintended brake release or power chair movement which could result in serious injury 1 Do not operate hand held transceivers transmitters receivers such as citizens band CB radios or turn ON personal communication devices such as cellular phones while the power chair is turned ON 2 Be aware of nearby transmitters such as radio or TV stations and try to avoid coming close to them 3 If unintended movement or brake release occurs turn the power chair OFF as soon as itis safe 4 Be aware that adding accessories or components or modifying the power chair may make it more susceptible to EMI and 5 Report all incidents of unintended movement or brake release to the distributor listed on the inside front cover of this manual Note whether there is a source of EMI nearby Important Information 1 20 volts per meter V m is a generally achievable and useful immunity level against EMI as of May 1994 The higher the level the greater the protection 2 The immunity level of this product is 20 V m HS 1500 User s Manual IDENTIFICATION OF PARTS Before attempting to drive this power chair on your own It is important that you familiarize yourself with the controls and how they operate Swivel Seat Super Responsive p Ba A Digital J oystick Controller t Flip Up Armrest Armrest Width Adjustment Thumbscrews One Piece Battery Pack Adjustable Footplate Lo
7. eight Adjustment Screw By adjust screw X1 to a comfortable position HS 1500 User s Manual e Free Wheeling Lever When the lever is in the N Neutral position the power chair can be moved without power When the lever is in the D Drive position the power chair can be driven Normal position is D Free Wheeling Levers remes e Circuit Breaker This is to protect your power chair from any excess current within the electrical parts If the power chair suddenly stops pushing the circuit breaker back in will help resolve this problem e Anti Tip Wheels Added safety feature to keep chair from tipping over Below Seat e Seat Rotation Lever Pull the seat rotation lever up to adjust seat s turning angle also can lift up the seat Do not turn the seat more the 180 degree due to length of joystick cable e Seat Lock Knob amp Pin Turn seat lock knob counterclockwise to loose Turn it clockwise to lock seat in position Remove the battery pack to locate the seat lock pin There are three holes on seat post to adjust seat height Be sure lock pin is fully inserted at its new height and knob is tightened if adjusted Seat Lock Knob Seat Lock Pin HS 1500 User s Manual OPERATING YOUR POWEF Before beginning your journey wit
8. erference from radio wave sources can cause the power chair to release its brakes move by itself or move in unintended directions It can also permanently damage the power chair control system The intensity of the interfering EM energy can be measured in volts per meter V m Each power chair can resist EMI up to a certain intensity This is called its immunity level The higher the immunity level the greater the protection will be Atthis time current technology is capable of achieving at least a 20 V m immunity level which would provide useful protection from the more common sources of radiated EMI The immunity level of this product is 20 V m There are a number of sources of relatively intense electromagnetic fields in the everyday environment Some of these sources are obvious and easy to avoid Others are not apparent and exposure is unavoidable However we believe that by following the warnings listed below your risk to EMI will be minimized Electromagnetic Interference and Warnings The sources of radiated EMI can be broadly classified into three types 1 Hand held portable transceivers transmitters receivers with the antenna mounted directly on the transmitting unit Examples include citizens band CB radios walkie talkie security fire and police transceivers cellular telephones and other personal communication devices Some cellular telephones and similar devices transmit signals while they are ON even when
9. h your new power chair make sure that the power chair is on a level surface and clear of any obstacles Although your power chair is able to climb slopes itis safer to practice on a level surface 1 Before operating your power chair check the following e freewheeling lever is on D e speed control switch is at the lowest speed repeatedly pressed left switch 2 Sit on the chair and fasten the seatbelt 3 When turning on the button on the joystick all power reserve LED lights should be lit All power reserve lights should not be flashing 4 While resting your arms on the armrests the joystick should be within reach By pushing the joystick slightly forward the power chair will move forward slowly Pushing the joystick fully forward it will move at normal speed Adjusting the speed control switch will also decrease and increase the speed Also with the joystick you are able to turn the chair 360 When the joystick is released and back in the neutral position the chair will stop Figure 9 5 Practice driving where there are no obstacles Start at the slowest speed and move forward and backward make some turns As you get more comfortable you can increase the speed by pressing the speed control switch repeatedly 6 When the power reserve Indicator is lit in only a few sections you should plan to recharge the batteries very soon HS 1500 User s Manual 7 1f the power chair suddenly stops and does not function locate
10. in mind these rules e Fully charge batteries at least once a month more if you use the power chair regularly Charge after each trip exceeding 3 kilometers 1 86 miles e If storing your power chair for some time one month or more make sure that the batteries are fully charged and on returning charge them again before using the power chair Batteries will only give the maximum performance after the power chair has been used and the batteries have been recharged up to 10 times For safety please follow the guidelines below 1 DO NOT use the charger if the power cord is damaged 2 DO NOT use an extension cord when charging your batteries A risk of fire and or electric shock could be encountered 3 DO NOT take apart the charger as this will void the warranty 13 HS 1500 User s Manual CARE AND MAINTENANCE Taking care of your power chair will keep it in top notch condition It is recommended that you have your dealer provide preventative maintenance service of your power chair on a regularly basis Here are a few maintenance guidelines BODY COVER If your power chair is dirty use a damp or lightly soapy cloth to wipe itdown Do not use running water to wash or rinse the power chair in order to protect the electrical parts Polish with an automotive liquid polish SEAT AND ARMRESTS The seat material used by C T M is a product of high quality and will remain in good condition for many years if treated responsibly
11. lt sea Controller Fault Consult a service agent A Series Bus l Consulta service agent Communications Fault J Problem All LED lights on joystick flash constantly X Solution Both Right and Left motors are on Neutral If the programmable parameter Motor Swap has been changed then left and right hand references in this table will need transposing 16 HS 1500 User s Manual Other Problems e Power chair will not move when the power is turned on 1 Check the Battery Level Indicator on the joystick All the LED lights should be on 2 Check the Self Diagnostic Warning Light It should be steady If itis flashing see the chart on page 16 for the problem identification 3 Check all electrical connections to be sure they are tight 4 Verify the batteries are connected correctly 5 If none of these suggestions correct the problem contact your authorized dealer e If charging your power chair over 14 hours and the light on the charger does not change to green then contact your authorized dealer Please note that your power chair is equipped with a controller that constantly checks the drive system for a safe and enjoyable ride If an error occurs the Battery Level Indicator will provide you an indication of the problem by way of flashing lights 17 HS 1500 SPECIFICATION User s Manual Overall Length Overall Width Overall Height Wheels Front Wheels Middle Wheels Rear Weight w Batteries Max Spee
12. not being used 2 Medium range mobile transceivers such as those used in police cars fire trucks ambulances and taxis These usually have the antenna mounted on the outside of the vehicle HS 1500 User s Manual 3 Long range transmitters and transceivers such as commercial broadcast transmitters radio and TV broadcast antenna towers and amateur HAM radios Other types of hand held devices such as cordless phones laptop computers AM FM radios TV sets CD players and cassette players and small appliances such as electric shavers and hair dryers so far as we know are not likely to cause EMI problems to your power chair Power Chair Electromagnetic Interference Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna source the EM fields from hand held radio wave sources transceivers are of special concern Itis possible to unintentionally bring high levels of EM energy very close to the power chair control system while using these devices This can affect power chair movement and braking Therefore the warnings listed below are recommended to prevent possible interference with the control system of the power chair Electromagnetic Interference and Warnings Warnings Electromagnetic interference EMI from sources such as radio and TV stations amateur radio HAM transmitters two way radios and cellular phones can affect the power chair Following the warnings liste
13. oved aside please follow these directions 1 Get off the power chair 2 Push the free wheeling lever to N 3 Move the power chair slowly to a safe location 4 Put the free wheeling lever back to D 10 HS 1500 User s Manual DISASSEMBLING RE ASSEMBLING YOUR POWER CHAIR Taking apart your power chair enables you to save space when keeping it in storage or to carry it along in your vehicle when going away from home Having the power chair disassembled is easier than ever since no tools are required To ensure your safety please have the freewheeling lever to D to engage the motor Disassemblino Unplug the J oystick Cable Connector A at the rear of the power chair See Fig 11 Pull the Seat Rotation Lever B underneath the front part of the seat to unlock Lift Seat C up to remove See Fig 12 Figure T pt J Remove the Basket by turning and removing the center Rivet D See Fig 13 Remove the Battery Pack E by holding the Battery Pack with one hand and the other hand pushing the Release Lever F to the rear of the chair See Fig 14 11 HS 1500 User s Manual Detach the chair frame by holding the Seat Post G with one hand the other hand pushing the Release Lever to the rear of the chair Lift the seat post to separate the Front Frame Assembly H from the Rear Frame Assembly I See Fig 15 Once all the parts have been disassembled you are no
14. owed to drop below 1 mm ELECTRICAL CONNECTIONS Verify the battery terminals and all plug connectors are secured and firmly attached If the battery terminals are corroded please contact your dealer for replacement HARDWARE Check that all hardware exist and are securely fastened Replace any missing hardware by contacting your dealer for information of parts Additional Information STORING Also between uses your power chair is best stored in a dry location at room temperature 15 HS 1500 User s Manual TROUBLESHOOTING a Here are some suggestions about solving problems you may have with your power chair There are 10 LED Self Diagnostic Warning Lights on the Control Panel To check the Self Diagnostic Warning Lights turn the power chair on and count the number of flashes Flash 4 l Code Recommended Action Motor current is over the controller Motor Current set limit Over Limit Fault Release the joystick to neutral and try again Try charging the batteries Battery Fault Batteries may require replacing Check the batteries and cabling 3 Left Motor Fault Check the left motor connections and cabling Check the right motor connections and cabling 2 Right Motor Fault Check the left k brak tor Left Park Brake Fault CCK me aa a connections and cabling Check the right park brake motor connections and cabling Right Park Brake Fault Display PCB Fault Consult a service User Interface Fau
15. w Profile Cast Aluminum Wheels with Multi Terrain Tires Power Reserve Indicator Seat Lock Knob On Off Switch Horn be v Armrest Button k Width Release Ci n Adjustment Lever i Thumbscrews Free Wheeling Lever Rear Reflectors l ane Speed Control Switch Anti Tip Wheels Figure 2 HS 1500 Joystick Figure 3 HS 1500 Power Chair Rear View HS 1500 User s Manual Jouystick Speed Control Switch By pressing the right switch you can increase the speed Pressing the left switch will decrease the speed Power Reserve Indicator There are LED Power Reserve lights on the joystick When all LED lights are on the batteries are fully charged When a few of the lights are lit the batteries need to be recharged These lights also act as Self Diagnostic Warning Lights When they flash there Is a problem with the power chair See page 16 for more information J oystick Length Extension Knob Loosen the knob to adjust the joystick length Charging Socket When charging your power chair use the power cord provided To correctly charge your power chair connect one end to the power chair charging socket and the other end to a wall outlet See Charging the Batteries page 13 for further instructions Charging Socket e Armrest Width Adjustment Thumbscrews Loosen the two thumbscrews to adjust the armrest width tighten again to lock in the desired position e Armrest H
16. w able to put the pieces in storage or in a vehicle for transportation See Fig 16 Re assemble To re assemble your power chair you can repeat the disassembly directions in reverse 12 HS 1500 User s Manual CHARGING THE BATTERIES Your C T M power chair is equipped with two service free 12V 14Ah rechargeable batteries and one 24V 2A on board charger Batteries must be charged before using the power chair for the first time and recommended to be charged up to 8 14 hours after each day s use Be sure the power switch is in the OFF position and the free wheeling lever is in the D position 1 Insert the battery charger cord into the charging socket on the joystick 2 Plug the other end of the power cable into a standard electrical wall outlet 3 Once the batteries are fully charged the light on the charger will change to green please unplug the power cord from the wall outlet and the power chair The power cord should be stored in a safe and dry location until it will be used again 4 f after charging your power chair over 8 14 hours and it does not function please check e fuse is not burned out e the power chair is turned off e circuit breaker is pushed in e if none of these is a problem contact your authorized dealer The time needed to recharge will vary depending on the depletion of the batteries Charging for longer than necessary will not harm the batteries They cannot be overcharged Keep
Download Pdf Manuals
Related Search