XR5 WASH USER MANUAL ENG REL 1.0.cdr
Contents
1. DMX CHANNEL 7 Parameter SHUTTER gt E Move range Mode Option Function degrees 0 9 Black out 10 23 Strobe random speed 24 37 Strobe speed 1 min 38 51 Strobe speed 2 52 65 Strobe speed 3 66 79 Strobe speed 4 80 93 Strobe speed 5 94 107 Strobe speed 6 max 108 121 Flash open speed 1 min 122 135 Flash open speed 2 136 149 Flash open speed 3 150 163 Flash open speed 4 max 164 177 Flash closed speed 1 min 178 191 Flash closed speed 2 192 205 Flash closed speed 3 206 219 Flash closed speed 4 max 220 227 Colours Macros in black out 228 233 Pan Tilt in black out 234 255 Open DMX CHANNEL 8 Parameter COLOUR Move DN le range Mode Option Function Value degrees 0 12 White 13 25 Colour 1 3200 K 26 38 Colour 2 5600 K 39 51 Colour 3 52 64 BiColour 3 4 65 77 Colour 4 78 90 BiColour 4 5 91 103 Colour 5 104 116 BiColour 5 6 117 129 Colour 6 130 142 BiColour 6 7 143 155 Colour 7 156 168 Bicolour 7 8 169 181 Colour 8 182 197 Bicolour 8 white 198 200 Right rotation speed 1 max 201 203 Right rotation speed 2 204 206 Right rotation speed 3 207 209 Right rotation speed 4 19 XR 5 WASH 210 212 Right rotation speed 5 213 215 Right rotation speed 6 216 218 Right rotation speed 72. A033 Moss A081 If you want to select the next projector just add 16 7 2 Selecting the DMX address 1 Press the UP DOWN key until you reach the required DMX channel The numbers on the display will start to flash but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The numbers on the display will stop flashing and the projector is now set to the new DMX address TRICKS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection 8 DISPLAY FUNCTIONS MAINS Electromagnetic ballast 230V 50 60Hz FUSE 3 15A MENU ENTER DISPLAY 11 DOWN UP DMXIN DMX OUT DISPLAY FUNCTIONS The XR5 display panel shows all the available functions Using these functions it is possible to XR 5 WASH change some of the parameters and add some functions Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol p gt shows which key has to be pushed to obtain the desired function ENTER Os _ en AGG IS Fr EF LU Clockwise ENTER PAN MOVEMENT INVERSION To reverse Pan movement from left to right and vice versa Fr EDAWN L L LI Counterclockwise ENTER MENU UP DOWN E d u ENTER UP DOWN L LI Clockwise ENTER TILT MOVEMENT INVERSION To
3. Electronic calibration of the motors Reset EEPROM Reset all settings ATTENTION by pressing this key you must repeat all previous calibrations po U m un J CCU CIL Exit from hidden menu 16 oo CAL PAN ALIGNMENT To align pan movement IS e 0 USS 2o _ e 10 UP DOWN E L U th ENTER I u UP DOWN Ln U ENTER TILT ALIGNMENT To align tilt movement IS C LC IS pani IS 17 1 IS UP DOWN l IL ENTER Ln a Up DOWN _ I ENTER SHUTTER ALIGNMENT To align shutter ac 170 Es I IS LUML IS ICO E ie I IS colour WHEEL ALIGNMENT To align colour wheel Ricco IF 1230 1 lt gt 12 1 IS UP DOWN Il tL ENTER IL LU UP DOWN IL 1 ENTER a EFFECT ALIGNMENT Effect alignement IS 1 C IS 1 710 IS es 171 1 IS UP DOWN el l Le ENTER In LU Up DOWN th i ENTER Z00M1 ALIGNMENT To align zoom1 IS 0 IS 1 710 IS IS 1 IS UP DOWN ci AL ENTER no Up DOWN Im l ENTER ZOOM 2 ALIGNMENT To align zoom 2 Ur Down ry AL ENTER c UP DOWN ic 1 ENTER CYAN ALIGNMENT To align cyan colour IF nt _ I La Ta IJ 13 1 IS ur Down III th ENTER LL UP DOWN I l ENTER MAGENTA ALIGNMENT To align magenta colour IS LU CO EB KIG IS 1I 1 IF UP DOWN l we L ENTER IL Ll UP DOWN IL l ENTER YELLOW ALIGNMENT To align yellow colour 16 XR 5 WASH 13 OPENING THE PROJECTOR HOUSING It is possible to inspect the inside of the projector by removing the co
4. User Manual Rel 1 0 GB 2 XR 5 WASH Le informazioni contenute in questo documento sono state attentamente redatte e controllate Tuttavia non amp assunta alcuna responsabilita per eventuali inesattezze Tutti i diritti sono riservati e questo documento non pu essere copiato fotocopiato riprodotto per intero o in parte senza previo consenso scritto della D T S DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche funzionali o di design a ciascun proprio prodotto D T S non assume alcuna responsabilita sull uso o sull applicazione dei prodotti o dei circuiti descritti The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein Les informations contenues dans le pr sent manuel ont t r dig es et contr l es avec le plus grand soin Nous d clinons toutefois toute responsabilit en cas d ventuelles inexactitudes Tous droits r serv s Ce document ne peut tre copi photocopi ou reproduit dans sa totalit ou partiellemen
5. 0 170 Colour conversion filters 3 200 K and 5 600 K Pan Tilt Pan 540 3 9 sec Tilt 270 2 6 sec 16 bit resolution 16 DMX channels Connections 4 XLR connectors In and Out with 3 and 5 pins Power supply Electromagnetic ballast 230 V 50 60 Hz standard On request 110 V 50 60 Hz Power consumption 350 W Remote Lamp on off via DMX Operating ambient temperature 10 40 Weight 20 Kg aiea H Packing Dimensions HxWxL E p 550 x 440 x 880 mm re U Weight L 27 Kg 5 XR 5 WASH 2 IMPORTANT SAFETY INFORMATION 2 1 Fire prevention XR5 can fit a Philips MSD250 2 or a Osram HSD250 2 or a GE CSD250 2 The use of any other alternative lamp is not recommended and will null and void the fixture s warranty Never locate the fixture on any flammable surface Minimum distance from flammable materials 1 MT Minimum distance from the closest illuminable surface 2 MT Replace any blown or damaged fuses only with fuses of identical value Refer to the wiring diagram if there is any doubt Connect the projector to mains power via a thermal magnetic circuit breaker 2 2 Prevention of electric shock High voltage is present inside the unit Unplug the unit prior to performing any function which involves touching the inside of the moving head including lamp replacement The level of technology present in the XR5 requires the assistance of specialised personnel for all servicing
6. Please refer to an authorised D T S service centre A good earth connection is essential for proper functioning of the projector Never connect the unit without proper earth connection The fixture should be located in places with a good air ventilation 2 3 Protection against ultraviolet radiation Never turn on the lamp if any of the lenses filters or ABS covering is damaged Their respective Shielding functions will only operate efficiently if they are in perfect working order Never look directly the lamp when it is on 2 4 Safety The projector should always be installed with bolts clamps and other tools that are capable of supporting the weight of the unit Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point The external surface of the unit at various points may exceed 70 C Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off Always replace the lamp if any physical damage is evident Never install the fixture in an enclosed area lacking sufficient air flow The ambient temperature should not exceed 40 C A hot lamp may explode so always wait for at least 10 minutes prior to attempting to replace the lamp Always wear suitable hand protection when handling the lamp 2 5 Level of protection against the penetration of solid and liquid matter The projector is classified as an ordinary appliance and its pr
7. 219 221 Right rotation speed 8 222 224 Right rotation speed 9 min 225 228 Stop 229 231 Left rotation speed 1 min 232 234 Left rotation speed 2 235 237 Left rotation speed 3 238 240 Left rotation speed 4 241 243 Left rotation speed 5 244 246 Left rotation speed 6 247 249 Left rotation speed 7 250 252 Left rotation speed 8 253 255 Left rotation speed 9 max DMX CHANNEL 9 Parameter CYAN gt ve Move S range Mode Option Function degrees 0 255 Proportional colour DMX CHANNEL 10 Parameter MAGENTA Move nn range Mode Option Function Value degrees 0 255 Proportional colour DMX CHANNEL 11 Parameter YELLOW gt a Move range Mode Option Function degrees 0 255 Proportional colour DMX CHANNEL 12 Parameter SPEED CMY DIMMER gt Move gt range Mode Option Function degrees 0 7 No Function 8 255 Variable speed from max to min 20 XR 5 WASH DMX CHANNEL 13 Parameter MACRO CMY COLOUR Move nes range Mode Option Function Value degrees 0 9 No Function 10 14 Macro 1 15 19 Macro 2 20 24 Macro 3 25 29 Macro 4 30 34 Macro 5 35 39 Macro 6 40 44 Macro 7 45 49 Macro 8 50 54 Macro 9 55 59 Macro 10 60 64 Macro 11 65 69 Macro 12 70 74 Macro 13 75 79 Macro 14 80 84 Macro 15 85 89 Macro 16 90 94 Macro 17 95 99 Macro 18 1
8. CONNECTION 8 6 1 Protection 7 DMX SIGNAL CONNECTION 9 7 1 DMX Addresses 7 2 Selecting the DMX address 8 DISPLAY FUNCTIONS 11 9 PAN TILT SPEED 14 10 FANS SPEED 11 ERROR MESSAGES 12 HIDDEN MENU 15 13 OPENING THE PROJECTOR HOUSING 16 14 PERIODIC CLEANING 14 1 Lenses and reflectors 14 2 Fans and air passages 15 PERIODIC CONTROLS 16 DMX PROTOCOLS 17 17 COLOUR WHEEL 22 4 XR 5 WASH 1 TECHNICAL FEATURES The XR 5 Wash is fitted with a Philips MSD 250 2 discharge lamp GY9 5 lampholder base with a colour temperature of 8500 K and a luminous flux of 18 000 Lumens Average lifespam is 2000 hours with replacement recommended before 2200 hours Other recommended lamps Osram HSD 250 2 GE CSD 250 2 The unit incorporates Motorized zoom 13 23 rotating and indexable beam shaper 0 170 frost filter 2 colour conversion filters 3 200 K and 5 600 K CMY colour generation a colour wheel 6 dichroic filters open with linear selection and electronic or electromagnetic ballast Optical group Fresnel lens 150 mm Borosilicate dichroic parabolic reflector Zoom Motorized zoom 13 23 Dimmer shutter strobo Linear dimmer Shutter Strobe from 0 85 flash sec to 10 flash sec Colours CMY color generation system with 3 palettes for gradual and linear insertion colour wheel 6 colours open Color change with blackout sync Effects Rotating and indexable beam shaper
9. in the path of the projector s movement 5 4 Risk of fire Each fixture produces heat and must be installed in a well ventilated place The minimum recommended distance from flammable material is 1 MT Minimum distance from the object being illuminated is 2 MT 5 5 Forced ventilation You will note on inspection that the unit features various air inlets and cooling fans located on both the base and head of the fixture These should under no circumstances be blocked or obstructed whilst the projector is in operation Doing so could cause the fixture to seriously overheat thereby compromising its proper operation 5 6 Ambient temperature The projector should never be installed in places that lack a constant air flow The ambient temperature should NOT exceed 40 C 6 MAINS CONNECTION XR5 with electromagnetic ballast operate at 230 VOLT 50 60 Hz Prior to connecting the unit to your mains supply ensure that the model in your possession correctly matches the mains supply available For connection purposes ensure that your plug is capable of supporting 3 15 amps at 230V Strict adherence to regulatory norms is strongly recommended Electromagnetic ballast 230V 50 60Hz 6 1 Protection The use of a thermal magnetic circuit breaker is recommended for each XR 5 A good earth connection is essential for the correct operation of the projector 7 DMX SIGNAL CONNECTION The unit operates using the digital DMX 512 1990 si
10. 00 104 Macro 19 105 109 Macro 20 110 114 Macro 21 115 121 Macros rainbow wait 0 122 128 Macros rainbow wait 2 129 135 Macros rainbow wait 3 136 142 Macros rainbow wait 4 143 149 Macros rainbow wait 5 150 156 Macros rainbow wait 6 157 163 Macros rainbow wait 7 164 170 Macros rainbow wait 8 171 177 Macros rainbow wait 9 178 184 Macros rainbow wait 10 185 191 Full colours rainbow wait 0 192 198 Full colours rainbow wait 2 199 205 Full colours rainbow wait 3 206 212 Full colours rainbow wait 4 213 219 Full colours rainbow wait 5 220 226 Full colours rainbow wait 6 227 233 Full colours rainbow wait 7 234 240 Full colours rainbow wait 8 241 247 Full colours rainbow wait 9 247 255 Full colours rainbow wait 10 XR 5 WASH DMX CHANNEL 14 Parameter EFFECTS Move A e range Mode Option Function Value degrees 0 19 No effect 20 39 Frost 40 255 Beam Shape DMX CHANNEL 15 Parameter ZOOM Move Dur range Mode Option Function Value degrees 0 225 Proportional DMX CHANNEL 16 Parameter LAMP RESET MODE 1 DEFAULT Move m una range Mode Option Function Value degrees 0 9 5 No Effect 10 60 30 Lamp OFF Active after 3 seconds 61 129 95 No Effect 130 179 154 Lamp ON Active after 3 seconds 180 200 190 No Effect 201 239 220 Internal Motors Reset 240
11. 255 247 Total Reset MODE 2 SAME AS XR 250 WASH gt a Move range Mode Option Function i degrees 0 29 No effect 30 85 Lamp OFF active after 3 seconds 86 170 Internal motor Reset 171 235 Total Reset 236 255 Lamp ON active after 3 seconds 22 XR 5 WASH 17 COLOUR WHEEL 3 COL1 COL2 COL3 COL4 0507K004 0507K003 0507C046 D01 0507C051 D01 CONV FILTER CTO CONV FILTER CTB WOOD SW 460 ORANGE LW590 TC3256 DL542 COL5 COL6 COL7 COL3 0507C042 D01 0507C047 D01 0507C041 D01 0507C053 D01 GREEN WB5055 RED LW 640 DARK BLUE SW490 AMBER LW 550 23 The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application ofthe products or circuits described herein MADE IN ITALY The Lighting Company D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 _ info dts lighting it www dts lighting it
12. LLATION XR5 may be either floor or ceiling mounted For floor mounting installations the XR5 is supplied with four rubber mounting feet on the base For ceiling mounted installations we reccomend the use of appropriate clamps to fix the unit to the mounting surface The supporting structure from which the unit is hung should be capable of bearing the weight of the unit as should any clamps used to hung it The structure should also be sufficiently rigid so as not to move or shake whilst the XR5 is moving Four quarter turn fast locks placed on the base of the units allow by using the two fast lock C clamps provided in the box to fix the unit in any position 5 1 Safety cable We recommend the use of a safety cable or chain connected to the Xr5 and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail Make sure that the iron cable or chain can bear the weight of the entire unit You may attach the safety chain to the two holes A located on the base of the fixture as shown in the picture below 5 2 Protection against liquids The projector contains electric and electronic components which should under no circumstances come into contact with oil water or any other liquid The proper unit functioning would be compromised should this occur 8 XR 5 WASH 5 3 Movement The projector has a maximum movement of 540 for Pan and 270 for Tilt DO NOT place any obstructions
13. OWN Fan control To control the fan speed DEFAULT 12 MENU UP DOWN ENTER UP DOWN SPEED control Pan Tilt Speed control Z DEFAULT 4 13 XR 5 WASH ome wi MENU UP D wN PL BS 18 oun ES ON OFF VIA DMX default LAMP FORCED ON Lamp always ON always OFF ENTER DECEDO Or lamp ON OFF selectable via DMX CE orr ES FORCED OFF ADJUST DU I To adjust the lamp with no mixer connected woe ENTER UP DOWN IS IE 128 It s possible to set the parameters for LIIL on PAN TILT and FOCUS Ci LE ic H CFI 133 f LU L LU cog ace arr gt Ta Lamp strikes counter KILL ENTER 1 LU CII Ee P C ATS 15 MENU UP DOWN 1 JUU ENTER L U U L UP DOWN IU U ENTER uP DOWN RESERVED Pan lock Tilt lock Pan free Tilt free PAN LOCK Dee LOCK THE PAN TO THE DESIRED VALUE PF ILL EA ENTER Ur DOwN U C CI IS IF 1 210 l ENTER Ur Down ICO TILT LOCK LI 1 IS IS WER IS LOCK THE TILT TO THE DESIRED VALUE LC Le H ENTER UP DOWN igs ENTER U C CI IS IE ITO AL ENTER ur D wn LL PAN FREE oO c_ IS we REMOVE POWER TO PAN MOTOR ras ENTER UP DOWN LER UEC gt IE Sy ENTER TILT FREE Lice ISP REMOVE POWER TO TILT MOTOR LL i IS E nico ENTER U C CI IS JL ENTER cc gt LIL ENTER MENU UP DOwWN L MILE sNTERurB w LO ENTER TIMER Y L IS O lamp life TIME reset possible UP DOWN nt c ENTER LU and total UNIT LIFE TIME reset not possible oo gt Li T Cree we UP DOWN E awh ENTER dU f ENTER 9 PAN amp TIL
14. T SPEED SPEE default 4 gt 4 You can set the PAN and TILT motors at high speed on your Xr5 Press menu until you see SPEE XR 5 WASH Press ENTER and select a speed with UP DOWN there are 4 speeds Confirm by pressing ENTER When you use speed 4 the highest PAN and TILT speed is very high and your projector may loose its path In this case the encoder corrects the position 10 FAN SPEED FANS default 12 Fan speed regulation makes it possible to reduce fan noise However the ambient temperature must be less than 35 C 11 ERROR MESSAGES ML ___ ERROR POSITIONING LLL OF COLOUR WHEEL COC ERROR POSITIONING LIL OF BEAM SHAPE EFFECTS J C ERROR POSITIONING ED OF ZOOM Sc Cr ERROR ALIGNMENT RE SENSORS OF ZOOM LENS AIIE ERROR INPUT wa IN AUTO MODE mec ____ ERROR INTERNAL LIDE COMMUNICATION CE ERROR SYNCHRONIZED SE FREQUENCY MEASURE SYNCHRONISM FOR LAMP ON ERROR ENCODER PAN ERROR ENCODER TILT ERROR DMX ADDRESS ERROR LOADING EPROM DATA ERROR COLOUR SENSOR CIRCUIT ZOOM 1 ERROR COLOUR SENSOR CIRCUIT ZOOM 2 15 XR 5 WASH 12 HIDDEN MENU For technical personnel only To operate this menu Connect the projector to the DMX controller DMX SIGNAL MUST BE CORRECTLY RECEIVED Reset the Xr5 reset from the MENU not from the DMX controller While reset is running press the MENU and ENTER keys at the same time R U T o rm U
15. gnal Connection between the mixer and the projector or between projectors must be carried out using a two pair screened g 0 5 mm cable and a CANNON XLR 5 or 3 pins connector 9 XR 5 WASH Ensure that the conductors do not touch each other Do not connect the cable ground to the XLR chassy The plug housing must be isolated Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one In this way all the projectors are cascade connected NB If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX address not valid DMX reception problem CONTROLLER STANDARD DMX 512 For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male XLR 3 5 pins connector with a 120 ohm resistor Between pin 2 and 3 The DMX terminator must be plugged into the last unit DMX out panel connector of the DMX line PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE XRL CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE PIN 3 PIN 2 10 XR 5 WASH 7 1 DMX Addresses XR 5 Wash have 16 DMX channels Set the following addresses on the mixer Projector 1 Projector 2 Projector 3 projector 6 A001 A017
16. if necessary Electrical components Check all electrical components for correct earthing and proper connection of all connectors refasten them if necessary Fuse replacement Locate the fuse which protects the lamp and electronics in the base of the XR5 Using a multimeter test the condition of the fuse replacing it with one of equivalent type if necessary 17 XR 5 WASH 16 DMX PROTOCOL 16 CHANNEL MODE 16bit 1 PAN msb 540 2 PAN Isb 3 TILT msb 320 4 TILT Isb 5 MOVEMENT SPEED 6 DIMMER 7 SHUTTER 8 COLOUR 9 CYAN 10 MAGENTA 11 YELLOW 12 SPEED CMY DIMMER 13 MACRO CMY COLOUR 14 EFFECTS 15 ZOOM 16 RESET DMX CHANNEL 1 Parameter PAN msb 540 DMX CHANNEL 2 Parameter PAN Isb DMX CHANNEL 3 Parameter TILT msb 319 DMX CHANNEL 4 Parameter TILT Isb DMX CHANNEL 5 Parameter MOVEMENT SPEED Move Paes range Mode Option Function Value degrees 0 10 Standard 11 25 Fast movement 26 127 Vector mode from fast to slow 128 247 Variable time reaction to DMX signal fast to slow 248 255 Slow reaction time to DMX signal DMX CHANNEL 6 Parameter DIMMER Move ul range Mode Option Function Value degrees 0 8 Black out 9 255 Proportional dimmer 18 XR 5 WASH
17. otection level against the penetration of solid and liquid matter is IP 20 6 XR5 WASH 3 MOUNTING THE LAMPS Warning Switch off the unit before replacing the lamp Philips MSD250 2 Power 250W Luminous flux 18 000 Im Colour temperature 8 500 K Lampbase GY9 5 Rated life 3 000 hours 1 Using a screwdriver remove the 3 screws X Y Z photo 1 which fix the lamp holder Photo 1 Photo 2 Photo 3 2 Remove the lamp holder assembly and insert the lamp photo 2 The lamp used on XR 5 is made in quartz glass and should be handled with care Always follow the instructions supplied in the lamp s packaging Never touch the glass directly but use the tissue provided in the lamp s packaging The GY9 5 lamp socket is not symmetrical DO NOT USE UNDUE FORCE ON THE GLASS In case of difficulty read again the instructions and repeat the procedure 3 Replace the lamp assembly and tighten the screws X Y Z which were previously removed photo3 3 1 Lamp alignment Attention we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit Photo 5 Alignment is carried out using the 3 adjusters A Band C During this operation you must have a uniform luminosity all around the projected area 7 XR5 WASH 4 VOLTAGE AND FREQUENCY The XR5 with electromagnetic ballast can operate at 230 VOLT 50 60 Hz 100 VOLT 50 60 Hz and 120V 50 60 Hz on request 5 INSTA
18. reverse Tilt movement from bottom upwards and vice versa FFI ien L L LI Counterclockwise ENTER rico onc i ay a gt IS LSE o 1 o gt LEN l LU l l IS LEN AR position ENTER REVERSE DISPLAY Sushansion Reverses display s reading depending on QU p gya IS the mounting position u position Soe On the ground or suspended ea LLL IS I CC pi s bcb EB GFF bispavorr I amp S DISPLAY STAND BY E To turn off the display after 5 seconds on Display IS Or leave it always on always ON IS na MENU Up DOWN i Moe ENTER DMX MODE To select DMX mode Mode 1 or Mode 2 UP Down UP Down Mod Mod a S DEFAULT SAME FIXTURE AS XR250 WASH 16 CHANNELS Pan amp Tilt 16 bit 16 CHANNELS Pan amp Tilt 16 bit ENTER 8 DISPLAY FUNCTIONS 12 XR 5 WASH SOFTWARE Software version TEL cg MOCT MENU UP DOWN tE SE ENTER UP DOWN ALL HILL MAGENTA 1 1 LU C TEST MODE ome wees Full test and single function test PAN rs YELLOW LLL mr Ef E E EFFECTS Ji nn Z n DIMMER Zi tui ZOOM cos SHUTTER 5H JE COLOR rol r CYAN IE IS CCE C gt MENU UP DOWN ra ENTER UP DOWN LI RESET ENABLED VIA DMX DS Al motors reset os RESET DISABLED VIA DMX IS CCP CJE TOTAL RESET Rn ICCC IG Ci IE MENU UP DOWN or Ic ENTER Jue ENTER DEFAULT To restore default setting Ener IS Z MENU Up DOWN LI L ENTER 63 63 Pch 8 motors Pch PAN amp TILT CD C IS IS MENU UP DOWN peu to ENTER UP D
19. t sans le consentement pr alable de D T S D T S se r serve le droit d apporter toutes modifications et am liorations esth tiques fonctionnelles ou de design sans pr avis chacun de ses produits D T S d cline toute responsabilit sur l utilisation ou sur l application des produits ou des circuits d crits Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas Con todo no se asume ninguna responsabilidad por eventuales inexactitudes Todos los derechos han sido reservados y este documento no puede ser copiado fotocopiado o reproducido total o parcialmente sin previa autorizaci nescrita de D T S D T S se reserva el derecho a aportar sin previo aviso cambios y modificaciones de car cter est tico funcional o de dise o a cada producto suyo D T S no se asume responsabilidad de ning n tipo sobre la utilizaci n o sobre la aplicaci n de los productos o de los circuitos descritos 3 XR 5 WASH INDEX 1 TECHNICAL FEATURES 4 2 IMPORTANT SAFETY INFORMATION 5 2 1 Fire prevention 2 2 Prevention of electric shock 2 3 Protection against ultraviolet radiation 2 4 Safety 2 5 Level of protection against the penetration of solid and liquid matter 3 MOUNTING THE LAMP 6 3 1 Lamp alignment 4 VOLTAGE AND FREQUENCY 7 5 INSTALLATION 7 5 1 Safety cable 5 2 Protection against liquids 5 3 Movement 5 4 Risk of fire 5 5 Forced ventilation 5 6 Ambient temperature 6 MAINS
20. ver as indicated below ATTENTION REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR S INTERNAL COMPONENTS 1 Loosen the 3 1 4 turn screws which fix the head covers photo 1 2 Once unscrewed simply lift the covers to access the internal components photo 2 Photo 2 14 PERIODIC CLEANING 14 1 Lenses and reflectors Even a fine layer of dust can substantially reduce the luminous output Regularly clean all lenses and the reflector using a soft cotton cloth dampened with a specialist lens cleaning solution 14 2 Fans and air passages The fans and air passages must be cleaned approximately every 6 weeks This periodic cleaning will depend of course on the conditions in which the projector is operating Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor If necessary clean the fans and air passages more frequently 15 PERIODIC CONTROLS Lamp The lamp should be replaced if there is any visible damage or deformation due to heat This will help to avoid the danger of the lamp exploding Mechanical parts Periodically check all mechanical parts gears guides belts etc for wear and tear replacing them if necessary Periodically check the lubrication of all components particularly the parts subject to high temperatures If necessary lubricate with suitable lubricant available from your D T S distributor Check the tension of the belts and adjust it
Download Pdf Manuals
Related Search