Quick Start Guide
Contents
1. please go to the Microtek Download Service site at ww microtek com tw service php to download and install any updates you may require For additional information about Microtek products please visit our website at www microtek com Copyright 2013 Microtek International Inc The following are trademarks or registered trademarks of their respective companies Microtek ScanMaker ScanWizard of Microtek International Inc All other trademarks or registered trademarks are the property of their 1 respective holders Specifications software and hardware bundles are subject to change without notice Delivery of technical support services subject to change without notice Not responsible for typographical errors English2. iew window Pall Fixing Film Jams Release buttons on the both sides of the iI front cover I 1 Openthe front cover by pressing the aaa Release button 2 After opening the front cover let the jammed film fall into the Output Tray and Front cover then remove it NOTE To remove the jammed f lm from the digitizer you have to open the front cover first Otherwise your film may be damaged if they are forcedly removed P Problems The LEDs on the front right panel of the digitizer indicate the status of the digitizer CL J C_ All Off Digitizer is off nz i j Green LED Flashing Orange Warming up or starting up the scanning Orange LED C ISS CI Orange off Scanning BE Cos AWOn Ready to scan First make sure that you have followed installation steps as described in this guide Then if your problem is listed here try the suggested solution 1 No light comes on when the digitizer is turned on Make sure your digitizer is connected to your computer and plugged into a power source 2 The Add Remove Hardware Wizard appears on your screen Click the Cancel button and close the ScanWizard Medi software Disconnect the Hi Speed USB cable from your computer and refer to the installation instructions in this guide 3 When trying to scan an error message appears on your screen that reads Can t Find Scanners Make sure your digit
3. izer is connected to your computer and plugged in to a power source see Step 4 Uninstall and reinstall the ScanWizard Medi software 4 After clicking Scan a blank screen appears Uninstall and reinstall the ScanWizard Medi software 5 When trying to scan an error message appears on your screen that reads Code 204 Scanning lamp or image sensor circuit failure Please don t select fast preview or draft scan This error message appears when the luminance of lamps is insufficient or surpassed Click OK first then contact the professional technician or call the Microtek Customer Service Department for the further help Do You Need Assistance Manuals If you have additional questions and need further instruction or information we provide electronic manuals for 1 Using your Medi 7000 2 Using the ScanWizard Medi scanning software To access the electronic manuals Insert the Medi 7000 CD ROM into your computer s CD ROM drive Next locate and click the Manuals option when the software installer window appears on your screen Finally select and click the title of the manual you wish to view Missing Items If your package is missing items please call the Microtek Customer Service Department Drivers amp Software Upgrades After you finish the installation of software if you found that the installed drivers and software cannot run your product or your computer system properly later
4. mu Medi 7000 Quick Start Guide Easy steps to getting started di N Unpack Contents Unpack your digitizer package and check for major components Medi 7000 Output Tray Main part Extension part of Output Tray Feed Tray Power Cord Software CD Hi Speed USB Cable Oo N a u J Install Software Important You must install software before connecting your digitizer Always close any open programs and turn off Anti virus utilities before installing software A Turn on your computer B Place the Microtek CD ROM into the CD ROM drive and follow the on screen instructions to install the driver and software C Restart your computer at the end of installation NOTE If the Software Installer screen does not come up automatically double click the following in succession My Computer the CD ROM icon then cdsetup exe to start the installer program da Copyright 2013 Microtek International Inc http www microtek com 4 149 004575 B September 2013 MICROTEK Feed Tray Install Digitizer Install Feed Tray A Look for two sets of the Feed Tray Holes at both ends of the front top of the digitizer Feed Tray Holes DI Insert and push down both sides of the Feed Tray into its compartment holes making sure the Feed Tray snaps i
5. nto place Install Output Tracy A Look for two sets of Output Tray Holes at both ends of the front bottom of the digitizer B Hang the extension part onto the compartment holes of the Output Tray making sure the extension part snaps into place O Insert and push down both sides of the main part of the Output Tray into its compartment holes making sure the Output Tray snaps into place Output Tray Holes Output Tray Extension part ST Output Tray Main part Output Tray whole unit y Connect Digitizer To the power cord A Connect the power cord to the left side of the digitizer B Plug one end of the power cord into a wall outlet or other power source To the Hi Speed USB cable C Connectone end of the Hi Speed USB cable to your computer left side of the digitizer E Turn the power switch at the front left panel of the digitizer to On once the scanner is detected by your system the LED lights on the front panel will brighten and the digitizer is ready to scan O D Connect the other end of the Hi Speed cable to the digitizer s USB port locating at the Scanning Basics Warning Do not place more than one piece of X ray film on the Feed Tray for doing so will damage the original film during the feeding process 1 Launch ScanWizard Medi To launch ScanWizard Medi as a stand al
6. one program double click the ScanWizard Medi icon on your desktop After ScanWizard Medi is started up the first time the Preview and Settings windows appear on the screen automatically 2 Load and Scan X ray film l Guide A Load and insert the X ray film into the Feed Tray with i the side to be scanned facing up and with the top end of X ray Film center the the film directing upwardly Facing up film on the tray Push the X ray film into the tray until the edge of it touches the bottom edge of the Feed Tray Once the film is detected by the digitizer the ScanWizard Medi will automatically recognize auto crop and perform a scan of the film and save it in your preferred folder or application 3 View the Image Double click the MSmart Images icon on the desktop to view the images or retrieve it from your preferred folder NOTE Your scan job can be carried out automatically with your own scanning settings For details on how to customize your scanning settings refer to the Medi 7000 User s Manual EA Mico k Sri za MENNE Ofyoesio Scanner View Preferences Correction Help Scan Job Untitled Type Gray Scale 12 bit v Resolution 300 gt Scan Frame x Scaling Output wi fi 4 00 ro H fi 7 00 Image Size 31 377 KB I een A Olin tata Std AAAA Zaia E o 2 9 JG UU A WY Nm O d Reset Settings window Prev
Download Pdf Manuals
Related Search