User Manual - Pacific-Wave
Contents
1. www pacificwave wireless com Page 15 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter 1 Check the coaxial cable or UTP5 twisted pair for open circuit and short circuit Check whether the plugs are positioned well 3 ee The circuit 2 The factory default of the the i the E1 signals device is 75Q BNC interface are lost If a 1200 RJ45 interface is used S5 6 S5 8 should be reconfigured See 4 2 3 3 The internal circuit of the equipment is damaged Send it to factory for repair port is connected 1 The setting of framing or Different f j un framing are different mode Make sure both devices has Setting Indicators are same code setting S1 1 between normal but 2 Setting of the time slots are 4 are Local communication f different Make sure both device f can not be done devices set same time slots and Remote via the dip switch 1 2 1 8 2 1 S2 8 Device 3 1 S3 8 4 1 S4 8 www pacificwave wireless com Page 16 of 162. www pacificwave wireless com Page 7 of 16 PACIFIC AA AVE User Manual PW FE1 4Eth E1 Ethernet Converter LOF Alarm indicator lamp for input signal out of frame in E1 line Constantly lightening indicates the alarm with local device flash indicates the alarm with opposite device Alarm status of opposite device can be detected only at framing mode LOS E1 link interruption alarm Always lights after starting up till synchronization is established It also lights in case of E1 link interruption or signal loss in communication AIS Always lights after receiving a alarm indication signal LOOP Always lights in testing if transmitting local loop flickers if remote E1 interface loop instructions or pseudo random sequence test instructions RAL Always light when E1 line of remote site cut down www pacificwave wireless com Page 8 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter 4 2 2 The rear panel of the FE1 4ETH bridge The AC input rear panel of FE1 4ETH Bridge is shown in figure 3 90 260VAC EW OFF ON S r E1 750 1 3 a dy 3 RX SS f 0 z rr 1 0 ELELEE LEE E mm i oo 3 oc E woe g E1 1200 Figure 3 AC input rear panel of FE1 4ETH Bridge 220V AC AC socket with two cores OF ON Power Switch for Electrical Power 8 Bits coded Switch System configure more descrip
3. optional from 1 to 31 Supporting 2 048Mbps transparent transmission in the E1 un framing mode The two 100BASE TX Ethernet interfaces support 100M half full duplex modes MAC addresses self learning and addresses filtering functions reducing the transmission load of the E1 circuit Built in 64Mbits SDRAM Ethernet data buffer memory improving the capability of Ethernet side anti outburst assuring high throughput of data transmission E1 circuit local loop tests Pseudo random sequence test facilitating the test of E1 circuit Perfect circuit test and alarm indication Optional AC 220V or DC 48V input for bridge of both architectures www pacificwave wireless com Page 5 of 16 PACIFIC 4A AVE PW FE 4EM E1 Ethernet Converter 3 Technical specifications Protocol G 703 G 704 G 736 G 823 1 431 IEEE802 3u 100BASE_TX Circuit Interface E1 Impedance 75Q physical interface BNC Impedance 1200 physical interface RJ45 Interface rate Framing N 64Kbps N 0 31 UN framing 2 048Mbps Coding HDB3 Jitter tolerance in accordance with G 823 Output Jitter lt 0 05UI Data interface 100OBASE_TX Impedance 100Q interface RJ45 Interface rate 100Mbps Coding Manchester Cable 75Q coaxial cable UTP5 twisted pair Transmission range Data interface 100m Circuit interface BNC 600m RJ45 300m Indicator indicating power connection states of data and circuit interfaces operation state test state and trouble a
4. 1 2 3 4 www pacificwave wireless com Page 11 of 16 PACIFIC AA AVE PW FE 4EM E1 Ethernet Converter SWITCH Status Function Description ON Unframed Full E1 used SW 0 2048KBps 31Time Slot S1 1 OFF Framed in User can set Xx64K X Time Slot to use SW 16 S3 1 ON CCS PCM31 Max 31 Timeslot Valid If SWO is off OFF CAS PCM30 Max 30Timeslot e 1st switch SWO S1 1 is used to set E1 framing non framing ON refers to non framing mode 2 048Mbps despite of whatever positions are set at other switches S2 S3 S4 2 to 3274 Switch S1 2 S1 8 2 1 S2 8 3 1 S3 8 4 1 S4 8 SW1 SW3 are respectively used to set 1st 31st time slots this only function if 1 1 is off Set at ON the corresponding time slot is selected Set at OFF the corresponding time slot is not selected The rate of E1 interface dependent on Number of Selected time slots For example if 3rd switch S1 3 is ON and other switches is OFF indicates that 2 4 Time slot is selected at this setting E1 rate is 64K If 7 S1 7 amp 10 2 2 switches is ON and other switches is OFF indicates that 6 amp 9th Time slots are selected E1 rate is 2 64K 128K e SW 16 S3 1 is used to set E1 frame structure to be PCM30 CAS mode or PCM31 CSS mode OFF PCM30 16th time slot not being used for transmission service ON PCM31 16th time slot can be used for transmission servic
5. Device 5 5 5 Switch NULL Not in Used 5 6 to 5 8 6 to 8th Switch To select between 750 or 1200 When S5 6 S5 8 is set 750 The E1 circuit uses BNC Coaxial cable When S5 6 S5 8 is set 1200 The E1 circuit uses RJ45 sockets and 120Q balanced twisted pair www pacificwave wireless com Page 10 of 16 E1 Ethernet Converter PACIFIC 4A AVE PW FE 4EM 5 Applications of FE1 4ETH Bridge 5 1 Definition of balanced twisted pair wire sequence 5 1 1 100BASE TX interface wire sequence The RJ45 Unshielded twisted pair for FE1 4ETH interface can use DCE or DTE standard stipulations it support AUTO MDI MDX function 5 1 2 E1 interface wire sequence 1 amp 2 are transmitting lines 4 amp 5 are receiving lines as shown below TX Positive end of data transmission TX Negative end of data transmission Idel RX Positive end of data reception RX Negative end of data reception Idel Idel Idel AM ONO GG SONS Figure 5 RJ45 balanced twisted pair wire sequence for E1 interface 5 2 Setting of DIP switch and jumper 5 2 1 Setting of E1 interface impedance Below are switch which allow user to set number of Time Slots according to the expected rate as shown by Figure 6 E1 TS 01 7 8 15 16 23 24 31 ON ON ON ON ON ON 1234567812345 67812345 67812345 67 8 S
6. PW FE1 4ETH Interface E1 Ethernet Converter User Manual PACIFIC AGAVE Providing Better Solutions for Telecommunication Industry http www pacificwave wireless com User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter Content 1 ProdUct GeSCription viscss cdsssvecctsscescadsevessccseseteavansess cvenaescsvenaeaeves 3 2 Main feature S 5 ciads cis ctssecaniensts cis eacveuis mene n a a 5 3 Technical SpecifiCationS cccceeeeeeeeecccceeeeeeeeeeeceeeeeaeeeeeeeees 6 4 Installation and panel description 7 AAW MPACKIN Gisicom enter ia 7 4 2 Front and rear panel of the device 00 eeeeeeeeeeeeeteeeeeteeeneee 7 4 2 1The front panel of the FE1 4ETH eee eeeeeeeeee 7 4 2 2 The rear panel of the FE1 4ETH eee 9 4 2 3 System test and configuration ecsecceeesseeeeeeees 10 5 Applications of FE1 4ETH 0 ec eeeecccceesseeeceeeneeeeesseeeeeeeneeeees 11 5 1 Definition of balanced twisted pair wire sequence 11 5 1 1 100BASE TX interface wire Sequence eeeeeeeee 11 5 1 2 E1 interface wire sequence ccceeesseceeesteeeeeeteeeees 11 5 2 Setting of DIP switch and jUMPeP eeeeeeeeeeeeteeeeeeeeeeee 11 5 2 1 Setting of E1 interface impedance c eeeeseees 11 5 3 Configuration of Ethernet connecting devices 13 5 4 Simple self test methods for devices and E1 circuits 13 5 5 Typical Applications eeeeeeeseeeeeesneeeeeeeneeesesee
7. according to the connected E1 environment This provides flexibility of network application In the framing mode the E1 interface provides a rate of N 64Kbps N 1to31 In Un Framing Mode E1 channel provides a rate of 2 048Mbps and accomplishes transparent transmission www pacificwave wireless com Page 3 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter If the FE1 4ETH bridge is used in the framing mode the transmission clock can be either provided internally i e using the main clocking timing mode INT or extracted from the E1 channel i e using slave clock timing mode The FE1 4ETH bridge provides plenty of self test functions supporting local loop It also provides pseudo random code test function to test error codes in the circuit It is proposed to use the products of this series in pairs Atypical application is shown in figure 1 SWITCH HUB SWITCH HUB Figure1 typical application of AN FE 4ETH bridge www pacificwave wireless com Page 4 of 16 User Manual PACIFIC KKNI PW FE1 4Eth E1 Ethernet Converter 2 Main features In accordance with the provisions of IEEE 802 3 802 3u Ethernet ITU T G 703 G 704 and G 823 protocols E1 interface framing un framing optional balanced 1200hm unbalanced 75ohm optional The E1 interface uses PCM31 mode supporting CRC check E1 interface main slave clock optional in the framing mode In E1 framing mode number of time slots is
8. e www pacificwave wireless com Page 12 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter 5 3 Configuration of Ethernet connecting devices The equipment uses 100BASE TX Ethernet interfaces and supports adaptive 100M half full duplex mode Ethernet devices connected to FE1 4ETH bridge such as SWITCH HUB Ethernet adapter card NIC etc can be set to 100M full duplex 100M half duplex adaptive 100M half full duplex and adaptive 10 100M 5 4 Simple self test methods for devices and E1 circuits Test 1 test of back to back connection Connect two FE1 4ETH bridge devices back to back ping the other s IP address on the two computers to test the two devices PC1 PC2 A B CI rey Test 2 test of E1 circuit transmission error codes Connect the device in the real operational environment check the E1 circuit with the loop and pseudo random sequence test function provided by the device 5 5 Typical applications Mode 1 connect Ethernet with E1 networks SDH PDH and DDN networks have already been widely adopted With E1 channels provide by such networks bridging connection and interconnection of two Ethernet networks at different locations can be easily realized by FE1 4ETH bridge www pacificwave wireless com Page 13 of 16 PACIFIC 4 AVE PW FE 4EM E1 Ethernet Converter SWITCH HUB Connecting two Ethern
9. eeneneeeeeeeae 13 5 6 Common questions and their maintenance 0 ce 15 www pacificwave wireless com Page 2 of 16 User Manual PACIFIC CANE PW FE1 4Eth E1 Ethernet Converter 1 Product description PW FE1 4ETH Interface Converter is an Ethernet bridge of high performance which accomplishes the converting between the 100M Ethernet port and the E1 port As an extended device of the Ethernet PW 1E1 4ETH bridge realizes interconnection of four Ethernet by using 1pc E1 channel provided by existing networks with low cost 100BASE TX RJ45 interfaces are provided at the end of Ethernet LAN to accomplish various functions including double Ethernet interface broad band shared MAC address self learning address filtering address table maintenance and flow control The device has 4 ETH port it can work like an intelligent L2 switch It can be reduce Net node dispense with device as HUB consequently reduce the malfunction node Our PW FE1 4ETH has the GUI NMS it can manage the converter like an intelligent L2 switch It can set the TAG VLAN on these 4 ETH port can set the special tag like Q in Q can configurable data rate from 32K 100M on each ETH port can do some QoS setting E1 interfaces conforming to ITU T G 703 and G 704 proposals are provided at the end of WAN supporting RJ45 and BNC connection modes The E1 ports support both framing and un framing architecture The user can select an operating mode for the E1 interface
10. et networks with an E1 network SWITCH HUB A Mode 2 Extend an Ethernet network with existing twisted pair or coaxial cable Connected with twisted pair or 75Q coaxial cable the E1 ports of FE1 4ETH Bridge support a transmission range of 300m or 600m Two Ethernet networks at different locations can be bridged by two FE1 4ETH bridge with existing twisted pair or coaxial cable m SWITCH HUB SWITCH HUB Extending Ethernet with existing twisted pair and coaxial cable www pacificwave wireless com Page 14 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter 5 6 Common Questions and Answer For independent interface converter reference for frame bridge No Symptoms Causes Remedies 1 The power is not connected Check the contact of power Cord and its converters 2 Failure at internal power module Send back to factory for repair 1 The type of the cable does not meet DTE DCE modes of Ethernet ports from Device 2 The crystal head of the cable Indicator LNK does Integrity is not well molded Check 2 not light when the test of link Quality of UTP cable Ethernet network has not 3 The rate setting of converter is connected passed or the network card is wrong See 5 3 4 The internal circuit of the equipment is damaged Send back to factory for repair The power indicator The power 1 does not light after circuit has starting up a failure
11. larm Dimensions LxWxD 210 x 40 x 140mm Power Supply 85V 264 Volt AC input 5Volt 1Amp Output 36V 72 Volt DC Input 5Volt 1Amp Output Power dissipation 3Watt Operation Temperature 0 C 50 C Storage Temperature 20 C 80 C Humidity 5 90 no Condensation www pacificwave wireless com Page 6 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter 4 Installation and panel description 4 1 Unpacking Check the accessories and spare parts when opens the package m FE1 4ETH Bridge m Operation manual A supply cord only for AC type m Two type of connector plugs BNC or RJ45 In case of missing or any damage during transportation immediately contact our offices or agencies 4 2 Front and rear panel of the device 4 2 1 The front panel of the FE1 4ETH bridge The front panel of the FE1 4ETH Bridge is shown as below sia PACIEKC AACAVE ETH E1 F O 6 A A A A O O PW 1E1 4Eth o P Ea SS A E Z Z Y g o PWR LKIAT LKIAT2 LKAT3 LKIAT4 LOS AIS LOF LOOP RAL Figure 2 front panel of FE1 4ETH Bridge Explanations for the two rows of indicators at the left are as follows POWER Power Always lights after starting up LK AT1 Flickers if ETH1 is connected and transmitting data LK AT2 Flickers if ETH2 is connected and transmitting data LK AT3 Flickers if ETH3 is connected and transmitting data LK AT4 Flickers if ETH4 is connected and transmitting data
12. tion in 4 2 3 E1 75Q BNC Tx Rx socket for 750hm impedance E1 interface E1 1200 RJ45 socket for 1200 impedance E1 interface ETH RJ45 socket for 100Mbps Ethernet interface The DC input rear panel of FE1 4ETH Bridge is shown in figure 4 ETH N 36 72VDC _ x r E1 750 1 3 a oh FG 48V GND 3 a RX z H HH ga l i o oo E J ETET 2 1 1200 Figure 4 DC input rear panel of FE1 4ETH bridge 48VDC DC 48Volt Power Supply Connector The others are the same as in figure 3 www pacificwave wireless com Page 9 of 16 User Manual PACIFIC COANE PW FE1 4Eth E1 Ethernet Converter 4 2 3 System test and configuration We can find 8pcs DIP Switch From Left to Right 1 to 8 Swich with below detail description 5 1 1st Switch Main Slave Clock setting valid only in Framing mode ON for Main clock INT CLK and OFF for slave clock LINE CLK 5 2 2 Switch BC_EN to set Bandwidth Coupling ON to follow bandwidth setting time slot of remote converter OFF to use bandwidth setting time slot of local converter 5 3 3 Switch LLOOP Local Loopback Setting For Testing Purpose ON for E1 interface in direct Loop back mode OFF for E1 Interface not in direct Loop back mode 5 4 4 Switch 7221_SEL to Set Version of Remote Corverter ON for working with the old Firmware Version Device OFF for working with same Firmware Version of
Download Pdf Manuals
Related Search