8-Port 10/100/1000Mbps + 2 SFP Shared Industrial Gigabit Ethernet
Contents
1. switches with SFP installed fiber NIC on a workstation or a Media Converter 3 Check the LNK ACT LED of the SFP slot on the front of the Industrial Gigabit Ethernet Switch Ensure that the SFP transceiver is operating correctly 17 E E Remove the transceiver module 1 Make sure there is no network activity by consult or check with the network administrator Or through the management interface of the switch converter if available to disable the port in advance 2 Remove the Fiber Optic Cable gently 3 Turn the handle of the MGB module to horizontal 4 Pull out the module gently through the handle Figure 2 4 Pull out from the transceiver Never pull out the module without pull the handle or the push bolts on the module Direct pull out the module with violent could damage the module and SFP module slot of the Industrial Gigabit Ethernet Switch 2 2 Mounting Installation This section describes how to install the Industrial Gigabit Ethernet Switch and make connections to it Please read the following topics and perform the procedures in the order being presented In the installation steps below this Manual use IGS 801 PLANET 8 Port Industrial Gigabit Switch as the example However the step for PLANET Industrial Gigabit Ethernet Switch is similar 2 2 1 DIN Rail Mounting The DIN Rail is screwed on the Industrial Gigabit Ethernet Switch when out of factory When need to replace the wall mount appli2. Step 6 Power on the Industrial Gigabit Ethernet Switch Please refer to the Wiring the Power Inputs section for power input The power LED on the Industrial Gigabit Ethernet Switch will light up Please refer to the LED Indicators section for meaning of LED lights Prepare the twisted pair straight through Category 5 cable for Ethernet connection Insert one side of Category 5 cables into the Industrial Gigabit Ethernet Switch Ethernet port RJ 45 port and another side of category 5 cables to the network devices Ethernet port RJ 45 port ex switch Pc or Server The UTP port RJ 45 LED on the Industrial Gigabit Ethernet Switch will light up when the cable connected with the network device Please refer to the LED Indicators section for LED light meaning Be sure the connected network devices support MDI MDI X If it does not support then use the crossover Step 7 fi 24 category 5 Cable When all connections are all set and LED lights all show in normal the installation is complete 4 Switch Operation 4 1 Address Table The Industrial Gigabit Ethernet Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This information comes from the learning process of Industrial Gigabit Ethernet Switch 4 2 Learning When one packet comes in from any port The Industri
3. Wa E NT Na KAE ENENG KA Da a 26 4 5 Auto Negotiation ss s ase eee anana nana nana aaa nana a nana aa nan nenen ane 26 SAN sana 27 Appendix A Networking Connection s saene aane nenen aane nane a nenen 28 A 1 Switch s RJ 45 Pin Assignments ss sasarane ena 28 A 2 RJ 45 cable Pin Assignments cccseceescescseestenseeenseenaeeeantegs 29 A 3 Fiber Optical Cable Connection Parameter ccccseeeeeeeeeeeees 30 A 4 Available SFP MOdUuleS sasae eaaa aana anana naen naen nan nan anan anana 31 1 Introduction 1 1 Package Contents Check the contents of your package for following parts e Industrial Gigabit Ethernet Switch x 1 User s Manual x 1 e DIN Rail Kit x 1 e Wall Mount Kit x 1 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair In the following section the term Industrial Gigabit Ethernet Switch means the IGS 802T 1 2 How to Use This Manual This Industrial Gigabit Ethernet Switch User Manual is structured as follows Chapter 2 Installation The chapter explains the feature functionality and the physical installation of the Industrial Gigabit Ethernet Switch Chapter 3 Application The chapter explains the Industrial Gigabit Ethernet Switch application Chapter 4 Switch opera
4. with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human wW health as a result of the presence of hazardous substances in mmm i clectrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 8 Port 10 100 1000Mbps 2 SFP Shared Industrial Gigabit Ethernet Switch User s Manual For Model IGS 802T Revision 1 1 April 2011 Part No EM IGS_802T_v1 1 2350 AH0430 001 Table Of Contents La OCU HON asa aapa aaa apaa eds a aapa aa a ngaja a Na
5. 1000Mbps with 2 shared SFP Industrial Ethernet Switch 40 75 Degree C Model Number IGS 802T Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN55022 CLASS A 2006 EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 EN55024 1998 A1 2001 A2 2003 IEC 61000 4 2 2001 IEC 61000 4 3 2008 IEC 61000 4 4 2004 IEC 61000 4 5 2005 IEC 61000 4 6 2008 IEC 61000 4 8 2001 IEC 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer D Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager Len Taiwan 31 Dec 2010 Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw _http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei
6. 8 Port 10 100 1000Mbps 2 SFP Shared Industrial Gigabit Ethernet Switch IGS 802T User s Manual Trademarks Copyright PLANET Technology Corp 2011 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply
7. City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528
8. OP IGS80 10 100 1000Base T Ports 8 sss 12 48V DC Redundant power with polarity reverse Power Requirement l protection function Power Consumption 19 Watts 64 BTU Dissipation Installation DIN rail kit and wall mount ear Apes Provides one relay output for power fail Alarm Relay current carry ability 1A DC 24V Switch Specification Switch Processing Scheme Store and Forward Address Table Back pressure for half duplex IEEE 802 3x Pause Frame for full duplex Switch fabric 16Gbps Throughput packet per second 11 9Mpps Maximum Transmit Unit 1632bytes 10 100 1000Base T Cat 3 4 5 5e 6 UTP cable 100meters max EIA TIA 568 100 ohm STP 100meters max 1000Base SX Network cables 50 125um or 62 5 125um multi mode fiber optic cable up to 550m vary on SFP module 1000Base LX 9 125um single mode fiber optic cable up to 10 20 30 40 50 70 120 kilometers vary on SFP module Flow Control Standards Conformance IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet Standards Compliance IEEE 802 3ab Gigabit Ethernet IEEE 802 3z Gigabit Ethernet IEEE 802 3x Full Duplex Flow Control Regulation Compliance FCC Part 15 Class A CE IEC60068 2 32 Free fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration Operating 40 75 Degree C Storage 40 75 Degree C Humidit Operating 5 90 Storage 5 90 Non condensing Temperature 91 1 5 Physical Dimension IGS 802T Indu
9. Turn off the power After a while turn on power again Can install MGB SX or other non wide temperature SFP module into SFP slot of Industrial Gigabit Ethernet Switch Solution Yes it does However since the MGB SX and other non wide temperature SFP module cannot operate under 40 to 75 Degree C Please pay attention to this point 27 E Appendix A Networking Connection A 1 Switch s RJ 45 Pin Assignments 1000Mbps 1000Base T 10 100Mbps 10 100Base TX RJ 45 Connector pin assignment MDI MDI X Media D dant Interface Contact Media Dependant Interface ae Ba T rans a as es e Pereo oen AA ne es dS 128 A 2 RJ 45 cable Pin Assignments The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable SIDE 1 SIDE 2 12345678 SIDE1 1 White Orange 1 White Orange 2 Orange 2 Orange 3 White Green 3 White Green 4 Blue 4 Blue 5 White Blue 5 White Blue 12345678 SIDE2 6 Green 6 Green 7 White Brown 7 White Brown 8 Brown 8 Brown Cross Over Cable SIDE 1 SIDE 2 12345678 SIDE1 1 White Orange 1 White Green 2 Orange 2 Green 3 White Green 3 White Orange 4 Blue 4 Blue 5 White Blue 5 White Blue 12345678 SIDE2 6 Green 6 Orange 7 White Brow
10. al Gigabit Ethernet Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 4 3 Forwarding amp Filtering When one packet comes from some port of the Industrial Gigabit Ethernet Switch it will also check the destination address besides the source address learning The Industrial Gigabit Ethernet Switch will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Industrial Gigabit Ethernet Switch will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered Thereby increasing the network throughput and availability 25 amp _ 4 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Industrial Gigabit Ethernet Switch stores the incoming frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network nee
11. bit Ethernet Switch is used for two DC redundant powers input Please follow the steps below to insert the power wire 1 Insert positive negative DC power wires into the contacts 1 and 2 for POWER 1 or 5 and 6 for POWER 2 O00000 00000 V1 V1 Ny V2 V2 Input J DC 12V 48V PWR1 Fault PWR2 Vi Vier V2 V2 2 Tighten the wire clamp screws for preventing the wires from loosing 1 2 3 4 5 6 Power 1 Fault Power 2 The wire gauge for the terminal block should be in the range between 12 24 AWG 2 1 6 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below Inserting the wires the Industrial Gigabit Ethernet Switch will detect the fault status of the power failure or port link failure available for managed model and then forms an open circuit The following illustration shows an application example for wiring the fault alarm contacts 1 The wire gauge for the terminal block should be in the range between 12 24 AWG 2 Alarm relay circuit accepts up to 30V max 3A currents 15 amp PT ELT TI HAE EJE B The Fault Alarm Contacts are energized CLOSE for normal Fault Alarm Contacts operation and will OPEN when failure occurs 2 1 7 Installing the SFP transceiver The sections describe how to insert an SFP transceiver into an SFP slot The SFP transceivers are hot pluggable and hot swa
12. cation with DIN Rail application on Industrial Gigabit Ethernet Switch please refer to following figures to screw the DIN Rail on the Industrial Gigabit Ethernet Switch To hang the Industrial Gigabit Ethernet Switch follow the below steps Step 1 screw the DIN Rail on the Industrial Gigabit Ethernet Switch Step 2 Lightly press the button of DIN Rail into the track 19 e Step 3 Check the DIN Rail is tightly on the track Step 4 Please refer to following procedures to remove the Industrial Gigabit Ethernet Switch from the track r Step 5 Lightly press the button of DIN Rail for remove it from the track 4 20 2 2 2 Wall Mount Plate Mounting To install the Industrial Gigabit Ethernet Switch on the wall please follows the instructions described below Step 1 Remove the DIN Rail from the Industrial Gigabit Ethernet Switch loose the screws to remove the DIN Rail Step 2 Place the wall mount plate on the rear panel of the Industrial Gigabit Ethernet Switch Step 3 Use the screws to screw the wall mount plate on the Industrial Gigabit Ethernet Switch Step 4 Use the hook holes at the corners of the wall mount plate to hang the Industrial Gigabit Ethernet Switch on the wall Step 5 To remove the wall mount plate reverse steps above 21 _ 3 Applicaiton In this paragraph we will describe how to install Industrial Gigabit Ethernet Switch and the installation points for the a
13. ds efficiency and stability The Industrial Gigabit Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Industrial Gigabit Ethernet Switch the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its respective domain reducing the overall load on the network The Industrial Gigabit Ethernet Switch performs Store and Forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 4 5 Auto Negotiation The STP ports on the Industrial Gigabit Ethernet Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another ne
14. n 7 White Brown 8 Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 29 E _ A 3 Fiber Optical Cable Connection Parameter The wiring details are as below E Fiber Optical patch Cables Standard Diameter Modal Bandwidth Max Distance micron MHz km meters 62 5 anes a 5 ae 1000Base SX 500 550 nal Pd ma s A Muti 5 550 1000Base LX A 4 Available SFP Modules The following list the available Modules for IGS 802T SFP Model MGB LA10 SFP Port 1000Base LX WDM TX 1310nm mini GBIC module 10km MGB LB10 SFP Port 1000Base LX WDM TX 1550nm mini GBIC module 10km MGB LA20 SFP Port 1000Base LX WDM TX 1310nm mini GBIC module 20km MGB LB20 SFP Port 1000Base LX WDM TX 1550nm mini GBIC module 20km MGB LA4O SFP Port 1000Base LX WDM TX 1310nm mini GBIC module 40km MGB LB40 SFP Port 1000Base LX WDM TX 1550nm mini GBIC module 40km SFP Port 1000Base SX mini GBIC module 550m MGB TSX 40 75 C SFP Port 1000Base LX mini GBIC module 10km MGB TLX SFP Port 1000Base LX mini GBIC module 30km MGB TL SFP Port 1000Base LX mini GBIC module 70km MGB TL7 31 _ PLANET Networking amp Communication EC Declaration of Conformit For the following equipment Type of Product 8 Port 10 100
15. paths With an intelligent address recognition algorithm the Industrial Gigabit Ethernet Switch could recognize up to 8K different MAC address and enables filtering and forwarding at full wire speed 2 1 2 Switch Front Panel Figure 2 1 shows a front panel of Industrial Gigabit Ethernet Switch e se gt 2 it T IGS 802T Figure 2 1 IGS 802T front panel 2 1 3 LED Indicators LED color Function Lit indicate the power 1 has power Lit indicate the power 2 has power FAULT Lit pee the either power 1 or power 2 has no LNK Green Lit indicate the Switch is successfully connecting to the network at 10 100 1000Mbps Blink indicate that the Switch is actively sending or receiving data over that port oo erage Off indicate that the Switch is inactively sending or receiving data over that port 131 2 1 4 Switch Upper Panel The upper panel of the Industrial Gigabit Ethernet Switch consist one terminal block connector within two DC power inputs Figure 2 2 shows the upper panel of the Switch Figure 2 2 shows upper panel of Industrial Gigabit Ethernet Switch eLeEenenege renee G00000000 0000000046 12345 ae HHHAAAIloo Vi Vit W V2 V2 Input a DC 12V 48V PWR1 Fault PWR2 OOOO 0C OO OOOO OOO OOO OD OO Figure 2 2 Industrial Gigabit Ethernet Switch upper Panel 2 1 5 Wiring the Power Inputs The 6 contact terminal block connector on the top panel of Industrial Giga
16. ppable You can plug in and out the transceiver to from any SFP port without having to power down the Industrial Gigabit Ethernet Switch As the Figure 2 3 appears R v D 5 lt A j ti Figure 2 3 Plug in the SFP transceiver Approved PLANET SFP Transceivers PLANET Industrial Gigabit Ethernet Switch supports both Single mode and Multi mode SFP transceiver The following list of approved PLANET SFP transceivers is correct at the time of publication MGB TSX SFP Port 1000Base SX mini GBIC module 550m 40 75 C MGB TLX SFP Port 1000Base LX mini GBIC module 10km 40 75 C MGB TL30 SFP Port 1000Base LX mini GBIC module 30km 40 75 C MGB TL70 SFP Port 1000Base LX mini GBIC module 70km 40 75 C Before connect the other switches workstation or Media Converter 1 Make sure both side of the SFP transceiver are with the same media type for example 1000Base SX to 1000Base SX 1000Bas LX to 1000Base LX 2 Check the fiber optic cable type match the SFP transceiver model e To connect to 1000Base SX SFP transceiver use the Multi mode fiber cable with one side must be male duplex LC connector type e To connect to 1000Base LX SFP transceiver use the Single mode fiber cable with one side must be male duplex LC connector type E Connect the fiber cable Attach the duplex LC connector on the network cable into the SFP transceiver 2 Connect the other end of the cable to a device
17. ra sae aa NE a Na a a aaa aa aaa a Aa A ga aa aaa aa aaa 6 1 1 Package Contents ss ss a anana nana aana ene 6 1 2 HOW to Use This Manual sarasa a ahan aa a a aaa aaa 6 PO FS sasira aaa aia naa aaa ii ap aaa b ana ag ka aa ga A Ba ag a dana 7 1 4 Product Specifications aaa a aaa ga EN aaa naa aana aaa a a Ka aka 8 L3 Physical UTS SION sa aaa said nan Da 10 2 NSA ENDI asana ani ranah PS ER 11 21 Produ t Descriptor 11 Bla Product OVECVICW jaka a aka a KK din KANG WAN KA 12 2 1 2 Switch Front PAN sa 13 ls EED IROLA tini snau na nn aaa 13 2 1 4 Switch Upper Panel ar i aranana aana nenen 14 2 1 5 Wiring the Power Inputs ccccccsseesetencensceensensaeteees 14 2 1 6 Wiring the Fault Alarm COntact ccccccssceeseeeseenseeeaees 15 2 1 7 Installing the SFP transCeiver saanane nenen 16 2 2 Mounting Instalatori jecic pana sana AANE I DAAR 19 2 2 1 DINERaN MOURNDRNG ank aaa na aan a ann Ka TA AA aa ei a 19 2 2 2 Wall Mount Plate Mounting scistsccsncdcvrencsasciisenaiewdaecsaons 21 Be APDICAN ON rss aaa BANA NA KERA A AREA Ann 22 A SWiteh QO DEN a aaa aa aaa Waa aaa a aja a aaa ak aa Ae a Ka 25 4 1 Address Table sasana aran anakan aa aaa ga saa aa gaga najana gan an gana aja aaa aaa 25 4 2 Learning scocsscstessiieceiesceteanaaerecdasasdeeteietieadiesdedenceencamaensedaescs 25 4 3 Forwarding amp Filtering A cn aasenipteeewiasdan ea nnneetpaeounssacceanens 25 4 4 Store nd FOrWA A asasaran naka ga kana ka WAH KN
18. shared with port 7 amp port 8 it also compatible with 1000Base SX LX through SFP Small Form Factor Pluggable fiber optic transceivers The fiber optical uplink capability guarantees the throughput to all nodes hooked into the network and the Gigabit Ethernet distance can be extended from 550 meters Multi Mode fiber cable up to 10 20 30 40 50 70 120 kilometers Single Mode fiber cable They are well suited for applications within the factory data centers and distributions With IP 30 industrial case protection the IGS 802T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets The compact IP 30 standard metal case of IGS 802T allows either DIN rail or wall mounting for efficient use of cabinet space Being able to operate under the temperature range from 40 to 75 Degree C the IGS 802T can be placed in almost any difficult environment The IGS 802T also possesses an integrated power supply source with wide range of voltages 12 to 48V DC for worldwide high availability applications requiring dual or backup power inputs The IGS 802T has 8K MAC Address table and offers wire speed packets transfer performance without risk of packet loss the high data throughput of the device makes it ideal for most Gigabit environments With a 16Gbps internal switching fabric and featuring auto negotiation support in each Gigabi
19. strial Gigabit Switch dimension W x D x H 135 x 87 x 56 mm Side View 6006000 Eloc 00000 o00po o00po ooo0opo0 o0oo ol 900p0B oo0o om 0000000 0000000 0000000 0000000 0000000 H a z Bottom View Front View Top View OOO0O00 Oe Ly 0688 Tee ee ey arara ra na 08 48 0146 Mounting Kit 8 Rear View Ss e e a DIN Rail Kit Q Mounting Kit E 10 2 Installation This section describes the functionalities of the Industrial Gigabit Ethernet Switch s components and guides how to install it on the desktop Basic knowledge of networking is assumed Please read this chapter completely before continuing 2 1 Product Description The IGS 802T equipped with eight 10 100 1000Base T auto negotiation ports and two SFP slots The two SFP slots are
20. t port the IGS 802T Industrial Gigabit Ethernet Switch can handle large amounts of data in a secure topology linking to a backbone or high capacity servers 11 _ The flow control function enables the IGS 802T to provide fast and reliable data transfer all of the RJ 45 copper interfaces in the IGS 802T support 10 100 1000Mbps Auto Negotiation for optimal speed detection through RJ 45 Category 6 5 or 5e cables The standard Auto MDI MDI X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables 2 1 1 Product Overview The PLANET Industrial Gigabit Ethernet Switch with 8 RJ 45 10 100 1000Mbps ports and 2 SFP shared interfaces for high speed network connectivity The Industrial Gigabit Ethernet Switch can also automatically identify and determine the correct transmission speed and half full duplex mode of the attached devices with its 8 ports The Gigabit ports can handle extremely large amounts of data transmission in a secure topology linking to a backbone or high power servers the Gigabit fiber optical uplink capability can guarantee the throughput to all nodes hooked into the network and distance can be extended up to above 120 kilometers with SFP module The Industrial Gigabit Ethernet Switch also supports Store and Forward forwarding scheme to ensure low latency and high data integrity eliminates unnecessary traffic and relieves congestion on critical network
21. tion The chapter explains the Industrial Gigabit Ethernet Switch transmit operation Chapter 5 Troubleshooting The chapter explains the troubleshooting of the Industrial Gigabit Ethernet Switch Appendix A This chapter contains cable information of the Industrial Gigabit Ethernet Switch 1 3 Product Features Physical Port e 8 Port 10 100 1000Base T RJ 45 with auto MDI MDI X function 2 SFP combo interface SFP Mini GBIC shared with port 7 amp port 8 Layer 2 Features e Supports Auto negotiation and 10 100Mbps half full duplex and 1000Mbps full duplex mode e High performance Store and Forward architecture runt CRC filtering eliminates erroneous packets to optimize the network bandwidth e Prevents packet loss with back pressure Half Duplex and IEEE 802 3x PAUSE frame flow control Full Duplex e Backplane Switching Fabric 16Gbps e Integrated address look up engine support 8K absolute MAC addresses e Automatic address learning and address aging CSMA CD Protocol Industrial Case Installation IP 30 Aluminum metal case Protection DIN Rail and Wall Mount Design 6 12 to 48V DC redundant power with polarity reverse protect function and connective removable terminal block for master and slave power e Supports EFT protection 6000 VDC for power line e Supports 6000 VDC Ethernet ESD protection 40 to 75 Degree C operating temperature 7 1 4 Product Specifications Model
22. ttention Public Construction Fiber Switch Serial over IGS 802T Ethernet Device IGS 802T Outdoor IP Camera Subway 2 a Outdoor P Camera ee ee eee eee ee eee ee a 100Base TX UTP I 1 ti _ 1000Base SX LX Fiber optic 4 Gigabit Fiber Switch IGS 802T Serial Device Server IP Camera f Serial Device over Ethernet 1 0 Serial Device over Ethernet Warehouse 100Base TX UTP 1 _ 1000Base T UTP I 1 1000Base SX LX Fiber optic Factory ma D1 DO ob 22 Harsh Climate IP Camera Weather Station IP Camera IGS 802T i 30km Switch 70km IP Camera IP Camera Winter season of Country Steel Factory IGS 802T 100Base TX UTP I aes 1000Base SX LX Fiber optic r Installation Steps Step 1 Unpack the Industrial Gigabit Ethernet Switch Step 2 Check the DIN Rail is screwed on the Industrial Gigabit Ethernet Switch Please refer to DIN Rail Mounting section for DIN Rail installation If the DIN Rail is not screwed on the Industrial switch If you want to wall mount the Industrial Gigabit Ethernet Switch then please refer to Wall Mount Plate Mounting section for wall mount plate installation Step 3 To hang the Industrial Gigabit Ethernet Switch on the DIN Rail track or wall please refer to the Mounting Installation section 23 Step 4 Step 5
23. twork device usually at Power On or Reset This is done by detect the modes and speeds at the second of both device is connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full Duplex mode 1000Base T can be only connected in Full duplex mode i 26 5 Troubleshooting This chapter contains information to help you solve issues If the Industrial Gigabit Ethernet Switch is not functioning properly make sure the Industrial Gigabit Ethernet Switch was set up according to instructions in this manual The per port LED is not lit Solution Check the cable connection of the Industrial Gigabit Ethernet Switch Performance is bad Solution Check the speed duplex mode of the partner device The Industrial Gigabit Ethernet Switch is run at Auto negotiation mode and if the partner is set to half duplex then the performance will be poor Per port LED is lit but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the Industrial Gigabit Ethernet Switch doesn t connect to the network Solution Check per port LED on the Industrial Gigabit Ethernet Switch Try another port on the Industrial Gigabit Ethernet Switch Make sure the cable is installed properly Make sure the cable is the right type
Download Pdf Manuals
Related Search