Manual (english)
Contents
1. 180 202 208 230 235 240 245 250 159 164 169 174 179 201 207 229 234 239 244 249 255 255 LEE 021 Gold amber LEE 778 Millennium gold LEE 135 Deep gold amber LEE 164 Flame red White Color rotation Color rotation forward slow fast Stop Color rotation backwards fast slow Open Fast Medium Slow Open Zoom 19 24 IgnItion LED CONTOUR AMBIENCE WASH 12 ZOOM 6 Technical data Voltage AC 100 240V 50 60Hz Power consumption 198W LED Osram RGBW 12 x 10W Control DMX512 Master Slave Sound to light Auto Channels 14 CH Dimensions 263 3 x 183 x 340 4mm Beam angle 10 60 Weight 7 5kg Max number of device in series 8 pcs 20 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 21 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 22 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 23 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM Importer B amp K Braun GmbH IndustriestraBe 2 D 76307 Karlsbad Ittersbach www bkbraun com info bkbraun com Xi RoHS u ES 24 242. If the device may hang from the ceiling or from high beams the use of truss systems is mandatory The device may not be installed so it can swing freely in the room Please note Crashing down items can cause serious injuries Do not install the projector if you doubt the safety of a possible installation form Before installation make sure that the mounting surface has the ability to carry the tenfold point load of the own weight of the device Mount the device with the mounting bracket to your trussing system using an appropriate clamp 7 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM During overhead installation the device must be always secured by a safety rope which is designed to hold the twelvefold weight of device Only safety ropes with quick release safety fastener elements may be used Hang up the safety rope in the hole of the mounting bracket Direct the rope over the truss or an appropriate fastening point Hang up the end in the fastening element and tie up the locking nut A safety rope once exposed to failing load or damaged may not be used furthermore The maximum drop exceed must not exceed 20cm A safety rope once exposed to failing load or damaged may not be used furthermore Adjust the desired inclination angle via the mounting bracket and tighten the screw 8 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 2 Introduction Thank you for buying the LED Contour Ambience Wash 12 Zoom It is a powerful dev
3. pulse 85 89 Open 90 104 Closing pulse 105 109 Open 110 124 Random strobe 125 129 Open i 130 144 Random opening pulse 145 149 Open 150 164 Random closing pulse 165 169 Open 170 184 Burst pulse 185 189 Open 190 204 Random burst pulse 205 209 Open 210 224 Sine wave 225 229 Open 230 244 Burst 17 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 10 11 12 13 245 O O KS 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 255 255 255 255 255 14 19 24 29 34 39 44 49 54 59 64 69 74 79 84 89 94 99 104 109 114 119 124 129 134 139 144 149 154 Open Dimmer red 0 100 Dimmer green 0 100 Dimmer blue 0 100 Dimmer white 0 100 Colors White LEE 790 Moroccan pink LEE 157 Pink LEE 332 Special rose pink LEE 328 Follies pink LEE 345 Fuchsia pink LEE 194 Surprise pink LEE 181 Congo blue LEE 071 Tokyo blue LEE 120 Deep blue LEE 079 Just blue LEE 132 Medium blue LEE 200 Double CT blue LEE 161 State blue LEE 201 Full CT blue LEE 202 Half CT blue LEE 117 Steel blue LEE 353 Lighter blue LEE 118 Light blue LEE 116 Medium blue green LEE 124 Dark green LEE 139 Primary green LEE 089 Moss green LEE 122 Fern green LEE 738 JAS green LEE 088 Lime green LEE 100 Spring yellow LEE 104 Deep amber LEE 179 Chrome Orange LEE 105 Orange 18 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 14 155 160 165 170 175
4. the display Use the UP and DOWN button to adjust the address from 1 to 512 Once the address has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode 4 1 3 Dimmer Curve Select Dimmer curve press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Mode1 Mode 2 Mode 3 or Mode 4 mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode 4 1 4 Dimmer modes description Dimmer Modes 5 5 5 o on o 5 5 5 o O e DMX DMX 96 Opticallv Linear Square Law Inverse Square Law S curve Model Optically linear The increase in light intensitv appears to be linear as DMX value is increased Mode 2 Square law Light intensitv control is finer at low levels and coarser at high levels Mode 3 Inv Square law Light intensitv control is coarser at low levels and finer at high levels Mode 4 S Curve Light intensitv control is finer at low levels and high levels and coarser at medium levels 14 24 IgnItion LED CONTOUR AMBIENCE WASH 12 ZOOM 4 1 5 Pan Inverse Select PAN INVERSE press the ENTER button to confirm present mode will blink on
5. Connections 3 1 Electrical connections If you wish to change the power supply settings see the chapter Appendix Connect the fixture to the mains with the enclosed power cable and plug The earth has to be connected Cable EU Cable US Pin International Brown Black Live L Light blue White Neutral N Yellow Green Green Earth 3 2 DMX connections To make a DMX512 connection go ahead like it is described in the picture Make sure that you use shielded cable 3pole or 5pole XLR cables are suitable Important After the last device the line has to be terminated In order to do this you have to solder a 1200 resistor between the pins Data and Data You can solder this end resistor on a 3pin or 5pin XLR Plug this adapter into the DMX output of the device DMX512 Controller 3 3 DMX connection with terminator Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy environment like a disco for installations we recommend using a DMX terminator This prevents corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR T gt Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM connector with a 120 Q resistor between pins 2 and 3 which is then plugged into the XLR output socket of the last device in the series Please look to the bottom drawings COMMON DMX DMX DMX INPUT COMMON DMX DMX INPUT
6. DMX 1200 2 3 1 PIN 3 PIN 2 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 12 24 IgnItion LED CONTOUR AMBIENCE WASH 12 ZOOM 4 Control Using touch control switch and LCD display and this can be simply and easily set the address code and functions code If you view or modify the lighting feature set then press MODE button the LCD display will enter the menu interface Both there is a sub menu corresponding to the functional operation of the main menu Each of the menus is representative of the specific features of the lamp The specific content shows as the table menu below Set or browse lighting function press UP or DOWN button Press ENTER to save your changes or enter the submenu Press the UP or DOWN can change the numerical increase or decrease in value Press the MODE button to return to menu 4 1 1 Structure of the menu DMX Address 001 512 Mode 1 Dimmer Curve a Mode 3 Mode 4 Pan Inverse Yes No Tilt Inverse Yes No Back Light On Off Red 000 255 White Balance Green 000 255 Blue 000 255 Pan 000 255 Tilt 000 255 Red 000 255 Green 000 255 Manual Test Blue 000 255 White 000 255 Zoom 000 255 Dimmer 000 255 Strobe 000 255 Auto Test Temp XXX Fixture Time XXX Firmware Version XXX 13 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM Reset 4 1 2 DMX Address Select DMX Address press the ENTER button to confirm the present address will blink on
7. Safety related red flags IMPORTANT Handle with the dangerous electric voltages carefully With this voltage there is the danger to get a life threatening electric shock Always observe After taken the device from a cold room to a warm room it is not allowed to activate the device It is possible that thereby emerged condensed water damages the device Activate the device not until it reached ambient temperature 4 24 IgnItion LED CONTOUR AMBIENCE WASH 12 ZOOM Prevent that the power cable has contact with other cables Handle carefully with power cables and power connections Don t touch them with clammy hands Make sure that the voltage which is to connect not exceeds the specified values Make sure that it isn t possible to squeeze or damage the power cable with sharp edges Assure yourself with regular checks that there are no damages to the power cable or the device Don t switch the device in short time intervals e g in second cycle on or off Keep away children and laymen off the device Health risk Don t look directly into the light source At certain circumstances it is possible that some people get epileptic seizures This is especially true for individuals whose epilepsy was determined by a doctor Designated use This device was developed for professional use on stages in discos theatres etc The device is only approved for a connection up to 230V 50 60 Hz AC voltage and only for indoor use Regula
8. ding objects or surfaces should not be in contact with the device Make sure that during the installation and removal of the device the area below the place of installation is basically cordoned off This also applies to implementation of service The device has basically been protected by a suitable safety Make familiar yourself with the functions of the device before start up People without the experience should not handle with the device The most cause of functional disorder is inappropriate handling Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt For transport use the original packing or designated accessory to avoid damages during the transport For reasons of safety unauthorized changes are forbidden A usage of the device which differs from usages which are described in this manual can cause damages of the device In that case the warranty expires Additional you should notice that every differed usage is related with dangers and can cause e g an electrical short fire electric shock or crash Overhead installation Danger of life You have to observe the regulations of BGV C1 formerly VBG 70 and EN60598 2 17 Installations are to carry out by skilled personnel only 6 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM The suspension devices have to be build and measured so they can withstand for an hour the tenfold of the payload
9. e ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 13 Firmware Version Select FIRMWARE VERSION press the ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 14 Reset Select RESET press the ENTER button and all channels of the unit will return to their standard position 4 2 Set and calculate the DMX address If you use a standard DMX controller you can Addresses of 001 512 awarded in a universe The device requires 14Ch so you may need to address the first device to 1 now but 14 addresses blank including 1 to control the device Consequently the second device is addressed on 15 but not less as it would otherwise interfere with the functions of the first device The next device could now be set to address 29 43 and so on 16 24 IgnItion LED CONTOUR AMBIENCE WASH 12 ZOOM 5 DMX chart Channel ir Valueto Function from 1 0 255 Pan 2 0 255 Pan fine 3 0 255 Tilt 4 0 255 Tilt fine 5 0 255 Speed Pan Tilt Reset 0 9 No function 3 10 14 Reset 15 255 No function 7 0 255 Dimmer 0 100 Shutter 0 19 No function 20 24 Open 25 64 Strobe 65 69 Open 70 84 Opening
10. ice For a successful installation and operation please read this manual carefully 2 1 Product overview 10 11 12 34567 Display To show the various menus and the selected function Power If the LED lights the device is powered on DMX If the LED lights the device gets a DMX signal Menu To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected function Fuse T6 3A Protect the unit from damage of the over current Powercon In To connect the power cord AC 100 240V 50 60Hz Powercon Out Connect to supplv power to the next unit max 8 pcs DMX In 3 Pin For DMX512 link use 3Pin XLR cable to link the unit together DMX IN 5 Pin For DMX512 link use SPin XLR cable to link the unit together 9 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 13 DMX Out 3 Pin For DMX512 link use 3Pin XLR cable to link the next unit 14 DMX OUT 5Pin For DMX512 link use 5Pin XLR cable to link the next unit 2 2 Dimensions 340 4 263 10 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM 3
11. ice is suitable for indoor use not outdoors only e All modifications to the device will void the warranty e Repairs are to carry out by skilled personnel only e Use only fuses of the same type and original parts as spare parts e Protect the unit from rain and humidity to avoid fire and electric shocks e Make sure to unplug the power supply before opening the housing 1 1 FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 32 F 0 C or exceeding 104 F 35 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with water should not be placed on the set Keep away from sources of hum and noise Such as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When n
12. ignition MANUAL LED Contour Ambience Wash 12 Zoom IQNILCION LED CONTOUR AMBIENCE WASH 12 ZOOM 1 2 3 4 5 6 Table of contents Safety INSTUCUDAS ici la 3 1 1 FOR SAFE AND EFFICIENT OPERATION nn nnnnnn tran ern nn rnnnnnan ana n nn nzzzzzznzz 3 1 2 Further safety instructions sis 4 INTTOQUCTION a is 9 2 1 Product OVervieW iii ea iena e a nn na ice dees a seen ua canons de 9 2 2 Dimensions 10 Connections nono nan cnn cnn nono nana nana nana E nnnnanicainnns 11 3 1 Electrical conne tion si a 11 3 2 DMXconnections aj ias 11 3 3 DMX connection with terminator i 11 COMORES ie 13 4 1 1 Structure of the MENU 13 4 1 2 DMX Address a iia 14 4 1 3 Dimmer CUIVE AM nono ARA an nn nn conan anna n nano nana anna anna non nnn a nana aca nn ninas 14 4 1 4 Dimmer m des deseription uu2u 0 aan 14 4 1 5 Par Inverse unta f f tethenebsadoetens 15 4 1 6 TIMES dia 15 4 1 7 Back Light sssssss creuser ail 15 4 1 8 Whit balance 22 e a D dad cido ies 15 4 1 9 Mandal Nest abili ele alii 15 4 1 10 AUTO Ostia e neo lane 16 delli Tempio 16 4 1 12 Fixture TIMO eii datada coria 16 4 1 13 Firmware Versioni lla alal a a e ea 16 4 1 14 RES 16 4 2 Set and calculate the DMX address 16 A A e Oe ee 17 TECHNICAL A A 20 2 24 IgnItion LED CONTOUR AMBIENCE WASH 12 ZOOM 1 Safety instructions e This dev
13. n to adjust the value 125 255 Once selected press the ENTER button to setup go back to the functions without any change press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 9 Manual Test Select MANUAL TEST press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Pan Tilt Red Green Blue White Zoom Dimmer or Strobe Once you find a function or a color you wish to test press the ENTER button use the DOWN and UP button to adjust the values 0 255 Once finished the test press the ENTER button to save 15 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM go back to the functions without any change press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 10 Auto Test Select AUTO TEST press the ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 11 Temp Select TEMP press the ENTER button and the display will show the temperature of the unit To go back to the functions press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 12 Fixture Time Select FIXTURE TIME press th
14. ot using the device for an extended period of time be sure to disconnect the plug from the receptacle 3 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards 1 2 Further safety instructions IMPORTANT Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards IMPORTANT Keep away from water and humidity Make sure to unplug the power supply before opening the housing Please read careful through this manual before the first start up All persons which are entrusted with installation start up operation maintenance and repair of this device have to e Show a corresponding competence e Follow the lines of this manual e Face this manual as part of the product e Keep this manual over the lifetime of the product e Pass this manual to new owners of the device e Download the latest version of the manual
15. r breaks during operation increase the lifetime of your device Avoid convulsions or any form of forceful impact during the installation or the start up of the device Make sure that the device is not exposed excessive heat humidity or dust at the place of installation Take care that no cables are lying around You would endanger your own safety and also the safety of a third party It is not allowed to operate or store the device in an environment in which spray water rain humidity or fog is expected Humiditv or very high atmospheric humiditv could reduce the isolation of the device and could cause deathly electric shocks If you use fog devices the device has not be exposed to a direct smoke jet There has to be a safety distance of at least 0 5m between this device and the fog machine Make sure that the saturation of the fog has to enable a visibility of at least 10m 5 24 Ignition LED CONTOUR AMBIENCE WASH 12 ZOOM The ambient temperature has to be between 0 C and 40 C Avoid direct sunlight and close proximity to heaters You have also to attend it during the transport in closed motor vehicles You have to attend that with an ambient temperature von 40 C it is not allowed that the relative humidity exceeds 50 Operate the device not during thunderstorms Surge voltages could destroy the device Unplug the power supply during thunderstorms During the installation the use of the mounting bracket is obligatory Surroun
16. the display Use the DOWN and UP button to select the Yes pan inversion or No normal mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 6 Tilt Inverse Select TILT INVERSE press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Yes tilt inversion or No normal mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode 4 1 7 Back Light Select BACK LIGHT press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the On LED on or Off LED off mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about two seconds or wait for one minute to exit the menu mode 4 1 8 White balance Select WHITE BALANCE press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Red or Green Blue Once the mode has been selected press the ENTER button to setup use the DOWN and UP butto
17. without suffering a permanent detrimental deformation Basically installation has to be made by using a second separate suspension This can be e g a suitable net The second suspension must be designed and attached so no part of the installation can fall down in case of failure During construction reconstruction and deconstruction unnecessary stay in the range of moving areas on lightning bridges under elevated work stations or any other danger zones is forbidden The operator is obliged to following safety related and mechanical facilities e Before the first start up or after critical changes before restarting it has to be checked by an expert e Review in the frame of the inspection test at least all four years by an expert e Review by a qualified person at least once a year How to carry out the overhead installation In tidal fall you should install the device out of the lounge area of people IMPORTANT Overhead installation requires a high level of experience This includes knowledge of calculating the payload used installation material and safety inspections of the used material and the projector whereas the required experience is not limited to this Do not try to carry out installation yourself under any circumstances if you are not qualified Contact a professional installer An inappropriate installation can lead to injuries and or damaged properties It is not allowed to install the device in the grip area of people
Download Pdf Manuals
Related Search