Wall Plug Switch Schuko for Outdoor Use (IP44)
Contents
1. is able to switch electric loads up to 3500 W and can be switched wirelessly or using the local button Local Operation The local button allows to switch the device A short press on the button toggles the switch If it is in ON state the button turns off and respective in OFF state the button turns on Automated Switch Off Function If activated the switch will turn off automatically after a defined time This function is particularly useful if the switch is turned on using a motion detector of any other type of sensor In this case it is possible to further define the reaction of the switch on certain signals sent from a sensor This allows a very flexible application of the plug switch in the house Child Protection The device can be turned into a child protection mode In this mode all local operation is disabled The child protection mode MUST be turned on wirelessly However in protected by sequence mode it is possible to unlock the device for local operation with a triple click The unlock state will last for 5 seconds Association Z Wave devices control other Z Wave devices The relationship between one device controlling another device is called association In order to control a different device the controlling device needs to maintain a list of devices that will receive controlling commands These lists are called association groups and they are always related to certain events e g button pressed sensor triggers In case the ev2. right to make any alterations that arise as the result of technical development Phone 44 0 20 7419 5726 eMail info popp eu Web www popp eu
3. the button pressed for 5 seconds will enter the configuration menu A blinking blue LED indicates that this menu was entered Short click of the button will change the configuration option and a long min 2 seconds click confirms the selection The following options are supported e Blue Confirm firmware update e Red Local Behavior within the Z Wave Network On factory default the device does not belong to any Z Wave network The device needs to join an existing wireless network to communicate with the devices of this network This process is called Inclusion Devices can also leave a network This process is called Exclusion Both processes are initiated by the primary controller of the Z Wave network This controller will be turned into exclusion respective inclusion mode Please refer to your primary controllers manual on how to turn your controller into inclusion or exclusion mode Only if the primary controller is in inclusion or exclusion mode this device can join or leave the network Leaving the network i e being excluded sets the device back to factory default If the device already belongs to a network follow the exclusion process before including it in your network Otherwise inclusion of this device will fail If the controller being included was a primary controller it has to be reset first Inclusion and Exclusion are confirmed by a tripple click on the button Operating the Device Function Button The device
4. 009105 P PP Wall Plug Switch Schuko for Outdoor Use IP44 Manual PLUS Wall Plug Switch Schuko IP44 Manual EE Ne Stane ee eee cee cee emcee tcc mec ce rem mm remnant ga geseezep sau ssenscnesuasanecersassennapnessies 2 Product Description 2 0 ccctsccesssssceeeeeecccnseeceasseeeeeeeeeeeeseaeeeasseeeeeeeeeeeasseaeaaseeeeeeeeeeeeesaaeeansseeeeeeeeeeesaaaeaaseeeeeeeeesaaagaanaaseeeseeeeeasas 2 BEtoreiinstalatonisn rer ere teen eey errr eee rr eee reer eter er re erer rr eee ee er ee ere rere 2 Installation GUdelNe carer eeerene per errr ere err ett er rer reer rer reer reer A re rerrrer rer recta rere rte rer rere ere eer eer eer eer errr rer Ce EE TE 3 Behavior within the Z Wave Network ccccccsccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeesseeeeeeeseaeeseeeeeeaaeeseeeseaaaeeeeeees 3 Operating the By it ot gt paren me eee ere cer rrr 3 CNA POU SOO sists nee sens nreonnsans nee E E E E E E E eeepc 4 ASSOCIAWON Perera reer eT rer ee TTTrer re Terrrer rer Terre ree Terrer reer eerernrrer Terrrrr ror enrter rrr TTT er rerrr rr rere reer ere rr ren 4 e cio 0 geile gid gars les la iol cl dc ses eereeer err E reer rerrreerTrrererrr rere tree ert Teter tree etree terrier err rrr ee rrrrtrr rrr etn Tr nnn 4 Command ClaSSES ree eee eee eer Te TT rr EEA EEEO 5 Tecnica Dalda 6 Explanation of Z Wave specific TermS cscccccssecasssscencnsscecenssucassesneannencecenunucsssenneannnsceennunecs ss asecennnoneeeu
5. e sensors actuators and even remote controls e Primary Controller is the central organizer of the network It must be a controller There can be only one primary controller in a Z Wave network e Inclusion is the process of bringing new Z Wave devices into a network e Exclusion is the process of removing Z Wave devices from the network e Association is a control relationship between a controlling device and a controlled device e Wake up Notification is a special wireless message issued by a Z Wave device to announce that is able to communicate e Node Information Frame is a special wireless message issued by a Z Wave device to announce its capabilities and functions Support Should you encounter any problem please give us an opportunity to address it before returning this product Most questions regarding Z Wave wireless communication standard can be answered through the international community at www zwave info If your question can t be answered there please contact us by email info popp eu 2015 POPP amp Co While the information in this manual has been compiled with great care it may not be deemed an assurance of product characteristics Popp amp Co shall be liable only to the degree specified in the terms of sale and delivery The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from Popp amp Co We reserve the
6. ent happens all devices stored in the respective association group will receive a common wireless command Association groups Send reports on switch state change max nodes in group 5 Controlled by buttons max nodes in group 5 Configuration Parameters Z Wave products are supposed to work out of the box after inclusion however certain configuration can adapt the function better to user needs or unlock further enhanced features IMPORTANT Controllers may only allow configuring signed values In order to set values in the range 128 255 the value sent in the application shall be the desired value minus 256 For example to set a parameter to 200 it may be needed to set a value of 200 minus 256 minus 56 In case of a two byte value the same logic applies Values greater than 32768 may needed to be given as negative values too LED mode Parameter number 1 Size 1 Set LED indication mode Show switch default Operated by Indicator Command Class Automatically Switch Off after Parameter number 2 Size 2 If not Zero automatically switch device off after an user defined time O Disable default 1 65535 sec What to do on RF Off Command Parameter number 3 Size 1 Defines how to interpret RF Off Command Can be used in conjunction with Auto Off function Ignore to switch on the light by motion detectors and switch it off after some amount of time in case of multiple motion detectors each would try to switch t
7. he light off that would break logics Switch on to switch on the light on both ON and OFF paddle press on the remote and switch it off after some amount of time Button OFF click will still work if button operations are not disabled Switch off default Switch on if load is off else switch off Restore switch state after power cycle Parameter number 5 Size 1 Defines if the switch should restore switch state to the last prior to device power off power cycle O0 No turn off Yes default Energy consumption Parameter number 20 Size 2 Specify the consumption of the load in watts for the calculation of power consumption Maximum load 1800 W Value O Disabled default 1 3500 Off color Parameter number 21 Size 1 Color for OFF state Off default Re Green Blue Yellow On color Parameter number 22 Size 1 Color for ON state O TOE O 2 Gee gt O 3 Blue default Command Classes Supported command classes BASIC BINARY SWITCH ALL SWITCH METER Controlled command classes BASIC MULTI CHANNEL Technical Data Type T 1 25 A H Load 1 25 Ampere high shutdown capacity D 5 mm L 20 mm Explanation of Z Wave specific Terms e Controller is a Z Wave device with capabilities to manage the network Controllers are typically gateways remote controls or battery operated wall controllers e Slave is a Z Wave device without capabilities to manage the network Slaves can b
8. ons and fully complies with the Z Wave Plus standard The device supports secure communication and the firmware can be upgraded over the air OTA Before Installation Please read carefully the enclosed user manual before installation of the radio actuator in order to ensure an error free functioning ATTENTION Only authorized technicians under consideration of the country specific installation guidelines norms may do works with 230 Volt mains power Prior to the assembly of the product the voltage network has to be switched off and ensured against re switching The product is permitted only for proper use as specified in the user manual Any kind of guarantee claim has to be forfeited if changes modifications or painting are undertaken The product must be checked for damages immediately after unpacking In the case of damages the product must not be operated in any case If a danger free operation of the equipment cannot be assured the voltage supply has to be interrupted immediately and the equipment has to be protected from unintended operation Installation Guidelines The plug can be plugged into every wall outlet for Plug Type Schuko It is IP44 rated and can therefore be used both in dry environments as well as humid environments and outdoor Do not locate the device facing direct sunlight or dusty place The suitable ambient temperature for the device is 0 C 40 C Plugs must not be stacked and operated Configuration Menu Keeping
9. unaceenncennneneeen 6 SUPPO eererreee err eerrer cere crreerr er rerrr er ter renner renter raver rrr er rrerrrrrrerrerr rrrrer rer rent creer rrr errr errr reer errr rrr rrr rrr re rrr rrr 7 Quick Start This is a Z Wave actuator Inclusion and Exclusion are confirmed by a tripple click of the button Fast blinking LED indicates the factory reset state Please refer to the chapters below for detailed information about all aspects of the products usage Product Description This is a plug switch that can be placed between a wall outlet for Schuko plugs plug type F and electric devices plugged in by cord It can switch all loads up to 3500 W The device is IP 44 rated and can therefore be used both in dry environments as well as humid environments and outdoor Switching is controlled wirelessly using Z Wave or locally applying a button A multi color LED indicates the switching status and the assignment of the colors to the switching status can be defined by the user The device will report any change of the switching status to a central gateway regardless the origin of the switch local or wireless A built in virtual power meter will report the power consumption of the load attached However the user must configure the assumed constant power draw of the load The local button can control the local load but can also be used to control other functions in a Z Wave network The device is certified and tested against all important European Safety Regulati
Download Pdf Manuals
Related Search