LT4968 Focus HE Remote Iss 2 (Packing list updated)
Contents
1. INE UNIT Y 890 PC OWNER MANUAL INCLUDES USER INSTRUCTION amp INSTALLATION amp MAINTENANCE INSTRUCTIONS Please read these instructions carefully before you start installing or using this appliance Keep this booklet handy for future reference This appliance is For use in Great Britain or IRELAND only INFINITY FIRES Charlton amp Jenrick Ltd TELFORD SHROPSHIRE TF3 3AR 890 PC CONTENTS USERS INSTRUCTIONS SECTION ONE Introduction Consumer Protection Information 3 Heath amp Safety Notice ss 3 Introduction eee 3 Important Information i i itstststststsS 4 SECTION TWO Operating Appliance Lighting the Appliance 5 Replacing Hand Set Battery ss 6 Replacing Appliance Battery 8 SECTION THREE Cleaning Cleaning Trim and Fret or Fascia 8 Cleaning Black Painted Surfaces 2 8 Cleaning Pilot Assembly ss 8 Cleaning Glass panel _ _ ss s 8 Removing Glass Panel _ _ i i isisisisist 8 SECTION FOUR Fuel Bed Cleaning amp Layout Cleaning Fuel Bed 9 Log Fuel Bed Layouts panel _ _ s_ isi si rdsdsds 10 INSTALLATION INSTRUCTIONS SECTION FIVE Appliance Data 14 SECTION SIX Regulations and Warnings 14 SECTION SEVEN Siting the Appliance Flue Class 222 16 SECTION EIGHT to Install Appliance Checking the Flue and Fire Opening __ 16 Fitting the closure plate 17 Gas supply routing ss 17 Mounting the appliance ss 17 Connect the gas supply _ _ s 172. 03 14 890 PC SECTION NINE Checking Operation of Fire e Using suitable wooden studding or one of the metal stud systems available on the market such as SpeedLine partitioning system Construct a false chimney breast Retain the frame work using the fixing holes provided within the fascia metal work as shown below Further fixing will be required to retain the stud work against the Chimney front face Retain Frame Work using the fixing holes provided e Using suitable board and fixing cover both side and front sections of the false chimney 23 LT6352 issue 2 03 14 890 PC SECTION NINE Checking Operation of Fire Top Of False Chimney Breast e Using a 70mm core drill bit Cut out four holes 2 left hand and right hand in the top section of the false chimney construction The bottom hole should be positioned 265mm from the top return edge of the fascia The top holes should be positioned 150mm down from the top edge of the false chimney breast Fit 4 off Air Vent e Fit the four off 7Omm diameter circular soffit vents provided with the appliance e Connect and insert battery holder within the front section of frame assembly Finally locate the inlet cover within the frame assembly ADVISE CUSTOMER THAT The glass front of this fire acts as a dress guard conforming to BS 1945 1997 and satisfies the heating appliance regulations 1991 however a
3. 14 90 PC Users Instructions SECTIONTHREE Cleaning Continued Glass Side retaining Pins Bottom Retaining Bracket REMOVING GLASS PANEL Remove the five 7mm nuts holding the front glass panel retaining bracket and slide the bracket clear of the studs Lift the glass panel out of the bottom retaining bracket Before refitting the glass panel loosen the side clamps retaining the side glass panels Fit the front glass panel within the bottom retaining bracket position the glass panel central with the outer side edges of the panel running flush with the two side glass panels Slide the top glass front retaining bracket over the five fixing studs and fit and tighten the 7mm nuts making sure again that the glass panel is flush and central Final tighten the four 7mm nuts retaining the LH and RH glass panels SECTION FOUR Fuel Bed Cleaning and Layout Important Black Glass back panel needs to be fitted before fuel bed is laid Ensure 3 tabs at back of tray are pushed down slightly Remove the 2 glass liner brackets fixed with 2 screws and washers the brackets are located on the top ceramic Place glass at the back of the fire ensure the textured side of the glass is facing the back of the fire and also that the glass is above the 3 tabs Bend the 3 tabs up to support the glass and then bend the inner part of the tabs up further so it stops the glass falling forward 9 LT6352 issue 2 03 14 90 PC Users Instructio
4. Warning Label 1409 ID Label amp Packing Labels Restrictor Elbow 2613 Grommet 1092 7mm Nut Spinner Air Tray Part No 6081 Glass Panels 1 x rear 2 x side 1 x Front Log Fuel Bed 5641 AAA Battery 3 Bag Of Black Chippings 6463 Remote Control Hand Set Handset Holder 5910 Battery Holder and Warning Label Closure plate C Cell Battery 12 Outer Fascia Trimless 6605 Data Badge Warning Label 1409 ID Label amp Packing Labels Restrictor Elbow 2613 Grommet 1092 7mm Nut Spinner 70mm Circular Vents x 4 6608 7MM Open Spanner 5243 Serial Number Serial Number Inspector Inspector 33 LT6352 issue 2 03 14
5. a restriction and not rectify the problem Note Take care when cleaning in this area so as not to damage the pilot assembly GLASS CLEANING From time to time it will be necessary to clean the glass panel of your 890 PC fire We recommend you use a Ceramic hob cleaner these are available for all leading super markets i e ASDA TESCO SAINSBURY S Etc Brands of hob cleaning we have tested and found suitable are HOB BRITE amp VITRO CLEAN e Ensure the fire as been turned OFF for at least four hours to ensure it is cool e Remove the glass panel as described below e Lay the glass panel down on a flat working surface on top of an old opened newspaper with the side to be cleaned uppermost Follow the instructions on the Hob Cleaner Bottle On stubborn stains where the appliance as been used for a long period without glass panel being cleaned use a new Brillo Pad well wetted with the Hob cleaner applied directly to it e Ensure all the residues of the cleaner are removed with a damp cloth and the glass panel is completely dry before fitting to the appliance Important The appliance must not be used if the glass panel is missing or damaged Note The glass may discolour quickly when first installed and it should be cleaned This is due to the burning off process of the refractory shapes The top of the outer firebox is not a working surface and therefore you should avoid placing items on top 8 LT6352 issue 2 03
6. below for information Artificial Fuels Mineral Wool Insulation Material Refractory Ceramic Fibres Glass Yarn may be harmful if inhaled may be irritating to skin eyes nose and throat When handling avoid inhaling and contact with skin or eyes Use disposable gloves facemasks and eye protection After handling wash hands and other exposed parts If a vacuum is used for cleaning the coals or cleaning after servicing installation it is recommended that it is of the type fitted with a HEPA filter Disposal of refractory ceramic materials To keep dust to a minimum these materials should be securely wrapped in polythene and be clearly labelled RCF waste These materials are not classified as hazardous waste and should be disposed of at a site licensed for the disposal of industrial waste INTRODUCTION e The 890 PC as been designed and tested to the requirements of EN 613 and is suitable for use in GB Great Britain and IE Ireland e The 890 PC incorporates a single gas control which selects ignition pilot with variable setting between low and high settings and is operated via remote control The system is powered by a battery pack therefore no mains electrical supply is required e Like all appliances incorporating an aerated burner a low frequency noise may be heard this may be more noticeable on the low setting e The 890 PC incorporates a safety device in the form of an Oxygen Depletion System which constantly m
7. commission appliance REPLACEMENT OF INJECTOR Follow the burner tray removal sequence Undo the compression nut on the supply pipe Unscrew the locking nut holding the injector on the chassis Clean or replace the injector NOTE Do not use a wire or a drill to clean out holes Refer to the appliance data section for details Re assemble in reverse order 25 LT6352 issue 2 03 14 890 PCMaintenance Instructions SECTION TEN Maintenance Continued REPLACEMENT OF OXY PILOT ASSEMBLY NOTE If the pilot assembly is replaced it must be replaced by an identical unit from the same manufacturer and replaced as a complete unit Follow the burner tray removal sequence Undo the compression nut on the supply pipe at the pilot Carefully pull off the ignition lead Disconnect the thermocouple at the end of the main control valve Remove the cross headed nut holding the pilot to the chassis Carefully remove the oxy pilot Re assemble in reverse order REPLACEMENT OF CONTROL UNIT EDB e Remove the fixing screw from the EDB unit e Pull the bracket plus EDB unit forward to clear the firebox e Disconnect leads from control unit and remove two bolts e Re assemble in reverse order FLUE CHECK e Remove the fire from the opening Reversing fitting instructions but first remove fascia and glass panel plus Log shapes e Examine flue and rectify as necessary e Replace the fire referring to fitting instructions SECTION ELEVE
8. harmful effects produced Care must be taken to prevent any damage being caused to surrounding soft furnishing or decoration e g many embossed vinyl wall coverings may become discoloured if placed too close to the appliance 16 LT6352 issue 2 03 14 590 PC SECTION SEVEN Siting the Appliance Please note on 125mm diameter flue system the Spigot restrictor plate MUST be removed Class 1 Conventional Flue The chimney must have a minimum effective height of at least 3 metres Any permanent flue restriction or variable dampers are to be removed or locked fully open The chimney should be swept prior to installation if it has previously been used with solid fuel This is not necessary if the flue has previously been used with a gas appliance or if it is a new installation Precast Flue Please note the Spigot restrictor plate must be removed The appliance can be installed to a precast concrete or clay flue block system conforming to BS1289 or BS EN 1806 The appliance is suitable for installation conforming to older versions of BS1289 The cross sectional area must not be less than 13 000mm2 The chimney vertical height must not be less than 3m and be correctly terminated Metal Flue Box The appliance can be installed to a metal flue box conforming to BS715 with a minimum internal depth of 200mm The total height of the closure plate is 440mm and will accommodate a maximum opening of 430mm This allows a 10mm overhang The total width of t
9. set see Section 2 Press the ON OFF key for at least 2 seconds on release a bleep sound be heard and the ignition process will start If the fire continues to bleep this may indicate a loose connection or badly loaded batteries 19 LT6352 issue 2 03 14 890 PC SECTION NINE Checking Operation of Fire CHECKING GAS SOUNDNESS e Turn on the gas supply to the appliance and check for soundness in accordance with current codes of practice Turn off the gas supply at the external Isolation valve Remove the pressure test point screw from the inlet eloow and connect the pressure gauge Turn on the gas to the appliance at the Isolation valve Light the appliance as described in section 2 Check the inlet pressure is 20mbar 1 0 Turn off gas supply at the isolation valve Disconnect the pressure gauge and replace the pressure test point screw e Turn on the supply to the appliance and check the pressure test point for soundness with detection fluid LAY FUEL BED Important Refer to the Heath amp Safety Notice located on page 3 of this booklet before laying or replacing any refractory material In the event of replacing fuel bed components please use only the specified number of components as illustrated Only use fuel bed component provided for this appliance In the interest of safety and efficiency of your appliance when replacing the fuel bed it is essential that the existing fuel bed be removed and the new component
10. the fire is next operated the sleep mode will automatically appear unless it is re set to zero This can be done by pressing the O key and using the button to decrease the time set by 15 minute intervals until back to zero If you experience unexplained outing on the fire please check that the sleep mode is switched off 6 LT6352 issue 2 03 14 90 PC Users Instructions SECTION TWO Operating the Appliance Continued LOW BATTERY INDICATION APPLIANCE If you hear a repeated bleep sound come from the appliance this indicates the appliance battery pack is low and should be changed If this is ignored the system will go into a lock out mode which will not allow the appliance to be used until a new set of batteries are loaded NOTE The appliance cannot be used when the battery is completely discharged TO REPLACE APPLIANCE BATTERIES 6 High Power Alkaline C 1 5V a Remove the trim or inlet cover plate b Remove the battery holder from within the protective cover or battery holder and replace the six high power alkaline C batteries as a complete set WARNING batteries will overheat if fitted incorrectly when fitting the batteries ensure that they are fitted as per the marking on the rear of the holder i e minus of battery against spring e Once the new batteries are loaded the fire will continue to bleep until re set Press the ON OFF key for at least 2 seconds on release a bleep sound will be heard and the ignition pro
11. By The Department Of The Environment The Building Standards Scotland Consolidated Regulations Issued By The Scottish Development Office e IN IE ireland The appliance must be installed by a competent person and installed in accordance with the current edition of I S 813 Domestic Gas Installation the current building regulations and the current ETCI rules for electrical installation if appropriate e Prior to the installation ensure that the local distribution conditions identification of type of gas and pressure and adjustment of the appliance are compatible G20 20mbar IMPORTANT NOTE The fire front fret or fascia supplied must be used with this appliance 15 LT6352 issue 2 03 14 WARNINGS The glass front of the fire act as a dress guard conforming to BS 1945 1971 and satisfies the heating appliance regulations 1991 However a guard conforming to BS6539 1984 must be used to protect young children the elderly or infirm This appliance incorporates a safety device in the form of an Oxygen depletion system IT MUST NOT BE ADJUSTED OR PUT OUT OF OPERATION THIS IS A NON SERVICABLE ITEM AND MUST BE EXCHANGED AS A COMPLETE ASSEMBLY USING ONLY THE ORIGINAL MANUFACTURER S PART A suitable proprietary fire surround with a 150 C minimum rating must be provided During initial firing an odour may be evident This is the starch binder used during the manufacture of the fibre components of the fire and there are no
12. Fitting the glass panel ss 18 Position remote receiver ss ssi 18 SECTION NINE Checking Fire Operation Check Gas soundness ssw 19 Checking Product Clearance ss 19 Fitting Trim ascia e a 20 Advice to Customer i 28 MAINTENANCE INSTRUCTIONS SECTION TEN Maintenance General eee 24 PilotLinting ss 24 o remove the burnertray ss 24 Replacement of gas control _ _ s i 24 Replacement of injectors 24 Replacement of Oxy pilotassembly ss 25 Replacement of Control Unit EDB 25 SECTION ELEVEN Wiring Diagram 25 2 LT6352 issue 2 03 14 PAGE 90 PC Users Instructions SECTION ONE Introduction Consumer Protection Information As manufacturers and suppliers of heating products we take every care as far as is reasonably practicable that these products are so designed and constructed as to meet the general safety requirement when properly used and installed To this end our products are thoroughly tested and examined before despatch IMPORTANT NOTICE Any alteration that is not approved by the appliance manufacturer could invalidate the approval of the appliance operation of the warranty and could affect your statutory rights Health and Safety Notice Important This appliance could contain some of the materials indicated below that could be interpreted as being injurious to health and safety It is the users installers responsibility to ensure that the necessary personal protective clothing is worn when handling these materials see
13. N WATE EIET LEUL Infra red receiver B Blue Bk Black Br Brown l G Green ignitor R Red Y Yellow B ia Control Unit T c to valve EDB T c to pilot 26 LT6352 issue 2 03 14 Infinity Fires Infinity 890 PC THIS IS YOUR EXTENDED FIVE YEAR PARTS WARRANTY PLEASE READ IT CAREFULLY AND ENSURE YOUR INSTALLER HAS FILLED IN THE FIRST PORTION KEEP IT IN A SAFE PLACE SO THAT IT IS AVAILABLE WHEN YOUR GAS SAFE ENGINEER CARRIES OUT THE ANNUAL SERVICE THIS IN NO WAY REDUCES YOUR STATUTORY RIGHTS THE WARRANTY COMMENCES FROM THE DATE OF PURCHASE YOU MUST RETAIN YOUR RECEIPT OR INVOICE AS PROOF OF PURCHASE THIS EXTENDED WARRANTY SPECIFICALLY EXCLUDES SOFT REFRACTORY COMPONENTS THE BULB AND ANY BATTERIES Terms and Conditions 1 2 3 4 NDOQ The appliance must be installed by a Gas Safe registered person The appliance must be used in accordance with the user s instructions The appliance must be serviced annually by a Gas Safe registered person The service log must be correctly filled out and the record of annual services must be up to date and supported by receipts in each case This warranty is not transferable and relates to the original installation only The Registration Form must be correctly filled out and returned The appliance has not been subjected to misuse or accident or been modified or repaired by any person other than the authorised employee or authorised representative of Charlton an
14. across the burner top plate area 10 LT6352 issue 2 03 14 90 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued Place three shapes shown within the burner top plate and air tray as shown Place three shapes as shown 11 LT6352 issue 2 03 14 90 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued Place a single layer of bark chippings on the burner top plate as shown Lay a single layer of bark chipping across the burner plate mi IS wR Bridge three of the shapes as shown 12 LT6352 issue 2 03 14 90 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued Bridge three of the shapes as shown Bridge Four of the shapes as shown 13 LT6352 issue 2 03 14 90 PC Users Instructions SECTION FIVE Appliance Data NATURAL GAS Gas ype L CATEGORY I2 H Gas Pressure 20 mbar 1 0mbar Pressure Test Point Location Gas inlet elbow Gas Input o 5 5 kW Gross Max 2 4 kW Gross Min NOx Classification 5 Injectors a Mk 360 Oxy pilot 9079 Gas Connection _ _ssi 8mm compression semi rigid or rigid Data Badge Location _ _ _s _ Located on the left hand side of the base of the appliance behind the trim Remote handset 3 x AAA 1 5 V Appliance 6 x 1 5V C Cell high power alkaline NOTE The efficiency of this appliance has been measured as specified in BS 7977 1 2009 and the
15. ained For a concealed connection e Remove the burner assembly by removing four screws holding the burner tray to carrier e fit the grommet over the pipe and seal around the inlet hole e Refit the burner unit and make connection between the supply isolating valve and the burner assembly inlet FITTING THE GLASS PANELS e Slide the LH and RH glass panels within the bottom location slots Fit the top retaining brackets over the two fixing studs LH amp RH and finger tighten using the four off 7mm nuts DO NOT TIGHTEN AT THIS STAGE e Lay the fuel bed in accordance with section four fuel bed lay out 18 LT6352 issue 2 03 14 890 PC SECTION EIGHT To Install the Appliance e Fit the front glass panel within the bottom retaining bracket position the glass panel central with the outer side edges of the panel running flush with the two side glass panels e Slide the top glass front retaining bracket over the five fixing studs and fit and tighten the 7mm nuts making sure again that the glass panel is flush and central e Final tighten the four 7mm nuts retaining the LH and RH glass panels POSITION REMOTE RECEIVER AND BATTERY POSITION Connect battery pack to appliance and insert batteries see section 2 Position the battery pack within the insulation sleeve or with the battery holder on trim less model Place the remote receiver on the fire box base Fit the three AAA batteries Supplied to remote hand
16. be installed by a competent person i e Gas Safe registered in accordance with the GAS SAFETY INSTALLATION AND USE REGULATIONS The Building Regulations or The Building Regulations Scotland or The Building Regulations Northern Ireland and The Current E E Wiring Regulations if appropriate In IE Ireland the appliance must be installed by a competent person and installed in accordance with the current edition of I S 813 Domestic Gas Installation the current Building Regulations and the current ETCI rules for electrical installation if appropriate The glass front of this fire acts as a dress guard conforming to BS 1945 1997 however a fireguard conforming to BS6539 1997 must be used to protect young children the elderly or infirm The appliance MUST NOT be used with the glass safety screen removed or if it is damaged or cracked During initial firing an odour may be evident This is the starch binder used during the manufacture of the fibre components of the fire and there are no harmful effects produced During the warming up and cooling down of the appliance you may experience some expansion and contraction noises These are normal During the normal operation of the fire some black staining may appear on some parts of the fuel bed This is quite normal and adds to the appearance of the appliance However if excessive black staining does occur it may be due to the fuel bed being incorrectly laid This should be checked
17. can be found on the data badge which is located on the left hand side of the appliance behind the trim or fascia At least once a years check for debris in the catchment area behind the fire and in the flue way lf soot has accumulated checks to establish cause rectify and clean flue or chimney accordingly When checking for debris in the catchment on the false chimney option The rear glass panel and inspection plates will need to be removed Turn off the gas supply by the isolating cock Remove the trim and glass assembly Remove the loose fuel bed components Disconnect battery leads and remove appliance battery Remove the fixing screw from the EDB fixing bracket Detach remote receiver from the fixing bracket Disconnect fire at inlet elbow and Undo the four burner tray fixing screws Pull carefully forward and remove For normal servicing the tray can be cleaned using a vacuum cleaner Whilst the tray is removed vacuum the firebox if necessary The Catchment Area can be accessed by removing the rear liner plus both inspection plate REPLACEMENT OF GAS CONTROL Follow the burner tray removal sequence Disconnect the thermocouple from the rear of the gas valve Undo the three compression nuts securing the pipes to the gas valve and remove the two screws fixing the valve to the bracket Clean service or replace gas valve Re assemble in the reverse order Turn on the gas supply check for soundness and re
18. cess will start If the fire continues to bleep this may indicate a loose connection or badly loaded batteries Battery lead boot cennection 54 Battery Holder Important If the fire burner or pilot is extinguished for any reason do not attempt to re light the pilot for at least 3 minutes 7 LT6352 issue 2 03 14 90 PC Users Instructions SECTION THREE Cleaning Warning Before you clean any part of the appliance ensures that the appliance is turned off and cold CLEANING FASCIA Abrasive or chemical cleaner should never be used CLEANING BLACK PAINTED SURFACES e These surfaces should be dusted regularly and any marks removed with a soft cloth e Abrasive or chemical cleaner should never be used CLEANING PILOT ASSEMBLY Before cleaning ensure that the appliance is turned off and cold In some instances you may experience ignition problems even when the appliance is new This may be due to the aeration hole in the pilot body see photograph being partial blocked with dust pet hairs or other foreign matter The source of this debris could be such things as carpet fibres decorating or pets etc To gain access to the pilot remove the ash pan cover and fretor fascia The pilot is located on the right hand side of the appliance any debris in or around the aeration hole should be remove using the nozzle of a vacuum cleaner It is advisable not to blow the debris into the hole as this may cause more of
19. d Jenrick Ltd The registration form must be returned within 3 months of purchase INFINITY HELPDESK NUMBER 0845 5195991 2I LT6352 issue 2 03 14 WARRANTY COVER mportant For future reference we suggest you record the following details here and keep the receipt as proof of purchase This information may be asked for when you contact the helpdesk Model WMD Serial No ef Wye de ite I atts le This information can be found on the label attached to the packaging and on the data badge which is located on the left hand side of the base of the appliance behind trim Retailer Name Address Date of Purchase 28 LT6352 issue 2 03 14 Service Log The following information must be complete and supported by receipts as part of the conditions of the extended five year parts warranty and the appliance must be registered by completing and returning the registration document last page of this booklet to Paragon Fires Date of First annual service Zane Engineer Name Gas Safe Registration No Pf tt ft td Date of Second annual service it ede Us Engineer Name Gas Safe Registration No Pf ff ff fd Date of Third annual service BETETT Engineer Name Gas Safe Registration No Pf ff ff fd Date of Fourth annual service Cot chee oe eee Engineer Name Gas Safe Registration No Py Ty TT TT We may introduce modifications to products from time to time and consequently the details given in this booklet are
20. er the decorative fascia up squarely and centrally The back face of the fascia will have cut out to give clearance for glass retaining brackets Use these slots as guide slide the fascia over the firebox The rear of the fascia as four location studs Lift the fascia and locate the studs within the slotted holes two LH and RH within the assembly of the fire box FALSE CHIMNEY FASCIA Two additional 10mm thick heat resistant boards will be required The sizes of the board are 956mm x 258mm e Insert a piece of 10mm heat resistant board within the top of the chimney fascia metal work as shown e Why supporting the fascia slide the EDB unit over the 3mm stud located on the bottom rear channel face Retain the unit using the M3 nut and washer provided 21 Slide the fascia over the fire box LT6352 issue 2 03 14 890 PC SECTION NINE Checking Operation of Fire e With the EDB board in place Offer the fascia up squarely and centrally The back face of the fascia will have cut out to give clearance for glass retaining brackets Use these slots as guide slide the fascia over the firebox e The rear of the fascia as four location studs Lift the fascia and locate the studs within the slotted holes two LH and RH within the assembly of the fire box e Place a further piece of 10mm heat resistant board 956mm x 258mm within the false chimney fascia 2 LT6352 issue 2
21. f the fireplace should be flat over an area sufficient to ensure a good seal with the closure plate The flat surface should extend for a height equal to that of the closure plate plus 20mm and for a width equal to that of the closure plate plus 40mm The closure plate has an opening at the bottom for the gas feed pipe The gap between the pipe and this opening should be sealed with tape after connection The closure plate must be fitted and sealed to the fireplace opening using a suitable heat resistant material GAS SUPPLY ROUTING Use rigid or semi rigid tube to connect the supply Determine the gas supply pipe route to the appliance before installing the fire MOUNTING THE APPLIANCE Fue Spgs The flue spigot must be capable of passing through the closure plate with a minimum clearance of 50mm between its open end and the nearest obstruction There must also be a minimum clearance of 150mm between the back of the closure plate and the back of the catchment space Place the fire in position and mark the wall through the holes in the fixing brackets LH and RH of the firebox Drill and plug the holes mon w 15C using no 10 wall plugs Place the Hlo S fire in position and secure with four no 10 x 2in Wood screws CONNECTING THE GAS SUPPLY Note An isolation valve may be fitted in the gas supply adjacent to inlet pipe Please Note that the restrictor plate should be angled so that access via the gas inlet cover can be obt
22. fireguard conforming to BS6539 1997 must be used to protect young children the elderly or infirm e The curing effect of heating the logs and other refractory components will cause an initial odour This is due to the starch used in the manufacturing process and is non toxic e Any debris should be cleaned from the appliance A vacuum cleaner can be used but only after all the loose logs have been removed e The appliance should be serviced annually by a competent person in accordance with these instructions and the appliance checked for spillage in accordance with the method detailed in these instructions Demonstrate the lighting and extinguishing procedures to the user and the removal and refitting of the Fascia and glass panel for cleaning Refer to the user section of this booklet f ventilation is fitted for any reason it must be checked regularly to ensure freedom from obstructions Hand these instructions over to the user 24 LT6352 issue 2 03 14 890 PC SECTION TEN Maintenance GENERAL TO REMOVE THE BURNER TRAY servicing should be carried out annually by a competent person such as a GAS SAFE registered person in accordance with the relevant regulations to ensure the safe and correct operation of the appliance Before commencing any service or replacement of parts turn off the gas supply to the fire After servicing check for gas soundness When ordering spare parts please quote appliance name and serial number these
23. gh and low flame If level 5 is currently active the icon max below the flame icon will appear To switch off the appliance press the button for at least 2 seconds and on releasing the button the appliance will bleep and then shut off The appliance can be switched off with out using the hand set by removing the appliance batteries located below the air grill cover When the batteries are removed there will be a delay up 3minutes after which double bleeps may be heard and shortly after the appliance will extinguish Ensure that the battery is reconnected once the fire as been extinguished The appliance cannot be operated without the use of the handset Room Thermostat mode The remote handset checks the room temperature at a fixed time intervals Depending on the difference between set room temperature and the actual room temperature the remote proceeds to modulate in one level steps Once the room temperature is reached it moves to standby position pilot Only 5 LT6352 issue 2 03 14 90 PC Users Instructions SECTION TWO Operating the Appliance Continued The icon PILOT will appear on the LCD display As soon as the actual room temperature falls below the SET room temperature the system will move from standby to the high flame level From this point it will proceed again the modulation process Note Due to the temperature checks at timed intervals the display temperature on the handset may exceed the room setting
24. he closure plate is 520mm and will accommodate a maximum opening of 510mm This allows a 10mm overhang PREPARING THE OPENING 395 510mm This area behind the trim fascia must be clear of combustible material and be flat for the seal 390 430m 100mm Min Depth Ce 100mm Min from floor to base Of the opening Note to a non combustible surface i e a hearth this can be reduced to 50mm CHECKING THE FLUE AND FIRE OPENING e Check that the chimney conforms to the required specifications as previously stated Examine the condition and carry out any remedial work including removing any debris from the base e lf the flue has been used for solid fuel it should be swept prior to the installation Prior to installing the appliance a smoke test using a smoke bomb should be carried out to check that satisfactory smoke clearance has been established lf all the smoke is not drawn into the flue pre heat the flue with a blowtorch or similar and re check If there is any uncertainty examine for the cause and if necessary seek expert advice No combustible material should be fitted inside the fireplace opening e When installing this appliance against a dry lined plasterboard wall ensure that any void between the plasterboard and the wall is sealed with a suitable non combustible material i e plaster or mortar 17 LT6352 issue 2 03 14 890 PC SECTION EIGHT To Install the Appliance FITTING THE CLOSURE PLATE The front o
25. ns SECTIONTHREE Cleaning Continued Re fit glass retaining brackets and position so they are pushed against the glass back panel then tighten screws Before you clean any part of the appliance ensures that the appliance is turned off and cold Use only the fuel bed components provided and no additional parts must added Incorrect positioning of the fuel bed components could result in the staining of the glass panel Important Refer to the Health amp Safety Notice located on page 3 of this booklet before cleaning or replacing any refractory material The fuel bed components are delicate and they should be handled with great care The loose parts and moulded shapes may be removed for cleaning They can be brushed very gently with a soft brush to remove dust or any deposits A vacuum cleaner may only be used after the loose components and moulded shapes have been removed Please make sure no loose shapes are placed directly on top of the pilot head Please see figure below CARE SHOULD BE TAKEN TO AVOID CONTACT WITH THE REFRACTORY LINING THIS IS A DELICATE SURFACE AND SHOULD NOT BE WIPED OR RUBBED 90 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued Please make sure no loose shapes are placed directly on top of the pilot head Please see figure below Leave a even gap between Keep Bark chipping clear of the pilot shield area the individual bark shapes Lay a single layer of bark chipping
26. onitors the oxygen in the room and will cause the fire to switch off if the oxygen level reduces for instance due to insufficient ventilation or a blocked flue lf this regularly occurs do not attempt to relight the appliance until a qualified engineer has checked it the problem may not be due to lack of air or a defective flue e The pilot can be left on standby setting or the pilot can be extinguished and relit each time the fire is used e To obtain an authentic fire sound a noise will be noticeable from the burner 3 LT6352 issue 2 03 14 90 PC Users Instructions SECTION ONE Introduction Continued The 890 PC is battery operated therefore no mains electrical supply is required Power to the appliance is provided by 6 high power alkaline 1 5V batteries C size a spare set of 6 C batteries is supplied with the appliance An audible repeated bleep warning indicates that the appliance batteries need changing or charging if rechargeable batteries have been used Important Batteries should be changed as soon as possible as the appliance will not light if the battery power gets to low IMPORTANT INFORMATION The appliance is for use on Natural Gas G20 20mbar only The chimney or flue unless new or previously used with a gas appliance shall be swept before installation if it has been used for solid fuel Failure to install appliance correctly could lead to prosecution In GB Great Britain the appliance must
27. prior to contacting a service engineer When using black glass liners care should be taken to ensure flames do not make contact with them as this will result in staining or permanent marking Due to the nature of the high gloss finish on the outer trim you may experience some markings in the form of a film This is quite normal and can be wiped off using a dry clean cloth when the fire is cold causing no damage to the trim The top of the outer firebox Trimmed Model is not a working surface and therefore you should avoid placing items on top 4 LT6352 issue 2 03 14 90 PC Users Instructions SECTION ONE Introduction Continued Care must be taken to prevent any damage being caused to surrounding soft furnishing or decoration e g many embossed vinyl wall coverings may become discoloured if placed too close to the appliance Combustible material i e wall panelling or wallpaper must be removed from behind the fire and fire fascia When the 890 PC is fitted with the false chimney breast it is strongly recommended that any proposed wall covering intended for use immediately above the appliance should be tested in the hottest position immediately above first Run the fire on high over a few days It is advised that this appliance is serviced annually as it is more likely to provide trouble free operation In GB Great Britain the fire does not normally require purpose built ventilation but if for any special reason purpose built ven
28. result is 74 1 natural gas The gross calorific value of the fuel has been used for this efficiency calculation Gastec have certified the test data from which it has been calculated The efficiency value may be used in the UK Government s Standard Assessment Procedure SAP for energy rating of dwellings When unpacking the appliance please check the following items are included Fuel Bed Owners Manual Trim and glass panels 14 LT6352 issue 2 03 14 890 PC SECTION SIX Regulations and Warnings This appliance must only be installed in Great Britain or Ireland The appliance is suitable for use on natural gas only GB Great Britain This fire does not normally require purpose build ventilation IE Ireland Permanent ventilation must comply with the current edition of IS813 In GB Great Britain It is the law that all gas appliances must be installed by a competent person i e a GAS SAFE registered installer in accordance with the Current Gas Safety Installation And Use Regulations as amended all relevant parts of the local and national building regulations and all relevant recommendations of the following British Standards Failure to do so could lead to prosecution The following are relevant codes of practice and British Standards B S 5871 B S 5440 PART 1 amp PART 2 B S 6891 This appliance must be installed to current versions of the above standards and include any relevant amendments to The Building Regulations Issued
29. s are replaced correctly as a complete set Lay fuel bed as described under Users Section Warning It is important that the fuel bed components are positioned as shown in these instructions lf the fuel bed components are not positioned correctly this may result in damage to the glass CHECKING FOR COMBUSTION PRODUCTS CLEARENCE IMPORTANT The smoke test must be carried out with the fire starting from cold e Light the fire and leave at maximum Input ie oe Spillage Tube e After five minutes fit the smoke _ e Close all the doors and windows match in a holder and position as illustrated with the head of the match just inside the test opening Within the downdraft diverter slot e Run the match along the top edge All smoke must be drawn into the test opening if the clearance is satisfactory e f spillage occurs wait a further five minutes and repeat the test Test Opening e Repeat the test with doors open and with any extractor fans in other rooms in operation If spillage is detected the cause must be discovered and the fault corrected if the fault cannot be corrected disconnect the fire from the gas supply and seek expert advice Spillage can be caused by a restriction in the flue system down draught or insufficient ventilation into the room where the fire is installed 20 LT6352 issue 2 03 14 90 PC Installation Instructions SECTION NINE Checking Operation of Fire FIT STANDARD FASCIA Off
30. subject to alteration without notice Infinity Fires Charlton amp Jenrick Ltd Telford Shropshire TF3 3AR Telephone 0845 5195991 29 LT6352 issue 2 03 14 PLEASE REGISTER YOUR 12 MONTH WARRANTY WITH US TODAY Simply detach this sheet from this booklet complete and return it in a stamped addressed envelope to INFINITY FIRES Charlton and Jenrick Ltd UNIT D STAFFORD PARK 2 TELFORD SHROPSHIRE TF3 3AR YOUR DETAILS Name Address Post Code ee Was ie ea TELEPHONE No PRODUCT DETAILS Model IMa NIA alee te Serial No Date of Purchase ft tt tt This information can be found on the label attached to the packaging and on the data badge which is located on the left hand side of the base of the appliance behind trim WHERE DID YOU PURCHASE THIS PRODUCT Name Address Post Code Ee TELEPHONE No 30 LT6352 issue 2 03 14 31 LT6352 issue 2 03 14 32 LT6352 issue 2 03 14 Infinity 890 PC Infinity 890 PC Trimless Product Serial No ID Label Prefix Product Serial No ID Label Prefix Burner Tray Box Assembly Burner Tray Box Assembly Back spigot Fitted Restrictor Label Back spigot Fitted Restrictor Label Air Tray Part No 6081 Glass Panels 1 x rear 2 x side 1 x Front Log Fuel Bed 5641 AAA Battery 3 Bag Of Black Chippings 6463 Remote Control Hand Set Handset Holder 5910 Battery Holder and Warning Label Closure plate C Cell Battery 12 Outer Fascia Data Badge
31. temperature before the appliance defaults to the pilot setting TO REPLACE BATTERY IN HAND SET 3 AAA TYPE BATTERIES Remove the cover from the rear of the handset and fit replacement battery Clock Regulation As soon as the batteries are fitted the timer digits will blink Using the arrow wo tu we tH er sa su key increase or decrease the hour minutes and week s value By pressing the gs m Pan T bad O will set and shift setting until complete yp E di i SET GES EE Changing Clock Setting During Operation i To amend timer setting press both the and O keys simultaneously for three seconds the written clock will appear To change the clock settings repeat the above described operation Change From Celsius to Fahrenheit g With remote OFF keeping pressed key at least for 5 seconds the temperature unit changes from Celsius to Fahrenheit degrees and vice versa Battery level indication Handset to When the batteries have to be changed in the handset the related icon will appear Setting the sleep mode To activate the sleep mode With the fire switched on press the O button The sleep symbol will appear top right The sleep symbol replaces the time indicator in this mode Using the arrow key increase the sleep mode in 15 minute intervals a small star will be visible next to the sleep symbol once any time is set Once the set time is reached the fire will completely switch off without any further intervention When
32. tilation is provided it should be checked periodically to ensure freedom from obstructions In IE Ireland permanent ventilation must comply with the current edition of IS813 SECTION TWO Operating the Appliance dai aei To light the appliance using the remote hand set a Point the remote control hand set in the direction of the appliance and press the button Continue to hold the button for approximately 2 seconds and release When released a bleep should be and heard ON OFF Key the appliance will automatically go through the ignition sequence and the pilot should ignite Once the pilot iS UP DOWN arrow key alight the appliance will automatically go to the high setting approximately 20 25sec If the ignitor stops sparking and the pilot fails to light press the button for at least 2 seconds and release again a bleep should be heard Then repeat the lighting procedure See note on page 7 With the appliance lit by pressing key the operational mode is switched from manual to Room thermostat setting and vice versa When Room thermostat mode is active the display shows the set temperature value and the AUTO icon will appear on the LCD display By using the arrow key the desired room temperature can be set When manual mode is active the display shows the MAN icon plus the flame icon and a five level bar icon setting By pressing the arrow key the flame picture can be adjusted at five stages between hi
Download Pdf Manuals
Related Search