Home

PSB-1000 series Programming manual

1. interface Return parameter LOC The instrument is set to front panel control EM The instrument is set to remote interface control RWL The front panel keys are disabled The instrument can only be controlled via the remote interface SYST COMM RLST LOC Sets the instrument to front panel control Example SYSTem COMMunicate USB FRONt STATe Description Queries the front panel USB A port state GW INSTEK PSB 1000 Series Programming Manual Query Syntax SYSTem COMMunicate USB FRONt STATe Return parameter 0 lt NR1 gt Absent 1 lt NR1 gt Mass Storage SYSTem COMMunicate USB REAR STATe Description Queries the rear panel USB B port state Query Syntax SYSTem COMMunicate USB REAR STATe Return parameter 0 Absent 1 Connected to the PC Set SYSTem COM Municate USB REAR MODE Description Sets or queries the rear panel USB B port mode Any changes to this setting are only applied after the unit is reset Syntax SYSTem COMMunicate USB REAR MODE 0 1 2 Query Syntax SYSTem COMMunicate USB REAR MODE Parameter 0 Disable Return parameter 1 Auto detect speed USB CDC 2 Full speed only USB CDC SYSTem ERRor Query Description Queries the error queue The last error message is returned A maximum of 32 errors are stored in the error queue Query Syntax SYSTem ERRor Paramter Return lt NR1 gt lt string gt Returns an error code followed by an error message as a st
2. A semi colon is used to join two related commands with the caveat that the last command must begin at the last node of the first command A semi colon and colon are used to combine two commands from different nodes meas volt dc meas curr dc 49 GW INSTEK PSB 1000 Series Programming Manual Command Forms Commands and queries have two different forms long and short The command syntax is written with the short form of the command in capitals and the remainder long form in lower case The commands can be written in capitals or lower case just so long as the short or long forms are complete An incomplete command will not be recognized Below are examples of correctly written commands Long STATus OPERation NTRansition form STATUS OPERATION NTRANSITION status operation ntransition Short STAT OPER NTR form stat oper ntr Square Brackets Commands that contain square brackets indicate that the contents are optional The function of the command is the same with or without the square bracketed items as shown below For the DISPlay WINDow STATe command both DISPlay WINDow STATe and DISPlay are valid forms 1 Command header 2 Space 3 Parameter 1 4 Comma no space before after comma 5 Parameter 2 Format Command APPLY 1 5 5 2 1 2 345 Parameters Type Description Example 50 GUIfISTEK REMOTE CONTROL Boolean Boolean logic
3. FUNC Key Enters the Function menu The function menu contains Power On Configuration settings Memory settings Voltage trigger settings and the Sequence menu Utility Key Enters the Utility menu The utility menu contains a number of system settings Utility File Key Pressing the file key allows you to copy rename and delete files 14 GU INSTEK GETTING STARTED Voltage Sets the constant voltage level ge Current Sets the constant current level OVP ELR PROT Sets the over voltage protection level CLR PROT Long press Holding the OVP key will clear any tripped protection functions OCP Sets the over current protection OCP level Scroll Wheel amp Both the scroll wheel and arrow Arrow Keys keys are used to navigate menu items pages or for incrementing decrementing Cx CD parameter values Enter Used to confirm settings and Enter menu items Lock Key Unlock Unlock Locks the front panel keys to Key Lock prevent accidentally changing panel settings Note The output can still be turned off when the key lock in active Unlock Key Long press Disables the key lock Output Key Turns the output on or off Clear Key m Clears entries that are made in the number entry dialogs Number Pad Used to enter values Ce s x v Cv 15 GW INSTEK PSB 1000 Series Programming Manual Rear Panel PSB 1800L M Rear panel terminals J1 C
4. STRING Only ASCII characters 20H to 7EH can be used in the lt string gt Syntax DISPlay WINDow TEXT DATA lt string gt Query Syntax DISPlay WINDow TEXT DATA Parameter lt string gt ASCII character 20H to 7EH can be used to in Return parameter the string parameter The string must be enclosed in quotes STRING Example DISP WIND TEXT DATA STRING Writes STRING to the display Query Example DISP WIND TEXT DATA STRING Returns the text data string on the screen Set DISPlay BLINk Description Turns blink on or off for the user text window Syntax DISPlay BLINk 0 1 OFF ON Query Syntax DISPlay BLINk Parameter 0 lt NR1 gt Turns blink OFF OFF Turns blink OFF 1 NRI Turns blink ON ON Turns blink ON Return parameter 0 lt NR1 gt Turns blink OFF 1 lt NR1 gt Turns blink ON Example DISP BLIN 1 Turns blink ON GW INSTEK REMOTE CONTROL Initiate Commands INI Tiate MMediate NAME eee 61 INITiate IMMediate NAME Set Description The INITiate command starts the TRANsient or OUTPut trigger See the trigger commands on page 86 for usage details Syntax INITiate IMMediate NAME TRANsient OUTPut Parameter TRANSient Starts the TRANsient trigger OUTPut Starts the OUTPut trigger Example INITiate NAME TRANient Starts the TRANSient trigger 61 GW INSTEK PSB 1000 Series Programming Manual Measure Command
5. amp TCP1801172162325 2268 PXI PXI System Unidentified amp Serial amp Parallel amp Software VISA Alias on My System PSB Remote Systems Device Type TCP IP Rew Socket Device Status This static device is working properly 11 Click the Configuration Icon Under the IO Settings tab check Enable Termination Character The termination character should be set as Line Feed n Tl 1cp10 1721623 25 2268 SOCKET 12 Click the Input Output icon Under the Basic I O tab make sure JDN n is entered in the Select or Enter Command drop box 13 Click Query The PSB 1000 will return the machine identification string into the buffer area GWINSTEK PSB 1800M XXXX TX XX XXXXXXXX 45 GW INSTEK PSB 1000 Series Programming Manual Tl 1c9100 172162325 2268 50CKET maiss vint Quy Read Read Status Byte Oax GW INSTEK PSB 1800M 0009 TO 70 A For further details please see the programming Note manual available on the GW Instek web site www gwinstek com GW INSTEK REMOTE CONTROL Error Log The Error Log function logs the error messages from the LAN GPIB and USB remote control and displays them on the screen Steps 1 Press the Utility key The Utility menu will appear on the display 2 Go to the Error Log gt gt gt setting using the scroll wheel and press Enter 3 Use the F1 F3 soft keys to error log source Log source LAN USB GP
6. more 1 of Copy to USB Copies the selected 2 sequence to USB Copy to Copies the selected SEQX sequence to another sequence Move to Move the selected SEOX sequence to another sequence Clear Clears the selected sequence from the memory more20f2 Returns to the previous menu level 23 GW INSTEK PSB 1000 Series Programming Manual Utility System Information Shows the serial number and software version Interface LAN MAC Sets the MAC address Address Host Name Sets the host name LAN Control Enables disables LAN DHCP Enables disables DHCP Rear USB Enables disables USB interface GPIB Enables disables GPIB interface Error Log LAN Log Lists LAN errors USB Log Lists USB errors GPIB Log List GPIB errors Clear Clears the error logs Exit Exits to the previous menu Speaker Enables disables the speaker Lock ModeO Mode disables all panel keys except the ability to turn the load off Model Mode disables all panel keys except the ability to turn the load on or off 24 GW INSTEK GETTING STARTED Utility Color Brightness Sets the brightness cont level Contrast Sets the contrast level Default Default brightness contrast settings Exit Exits to the previous menu Factory Restore Restore the factory Setting settings Exit Exits to the previous menu Calibra Not applicable to end tion users File Copy to Co
7. Disables the power switch trip for OVP or OCP OFF Disables the power switch trip for OVP or OCP 1 lt NR1 gt Enables the power switch trip for OVP or OCP ON Enables the power switch trip for OVP or OCP Return parameter lt Boolean gt Returns power switch trip setting Set SYSTem CONFigure CURRent CONTrol Description Sets or queries the CC control mode local control panel external voltage control external resistance control This setting is applied only after the unit is reset Syntax SYSTem CONFigure CURRent CONTrol 0 1 2 3 Query Syntax SYSTem CONFigure CURRent CONTrol Parameter Return NR1 Description 0 Local Panel control 1 External voltage control 2 External resistance control 10kO Io max 0kQ Io min 3 External resistance control 10kQ Io min 0kO Io max Set SYSTem CONFigure VOLTage CONTrol Description Sets or queries the CV control mode local control external voltage control external resistance control This setting is applied only after the unit is reset Syntax SYSTem CONFigure VOLTage CONTrol 0 1 2 3 Query Syntax SYSTem CONFigure VOLTage CONTrol 92 GW INSTEK REMOTE CONTROL Parameter Return NRI Description 0 Local Panel control 1 External voltage control 2 External resistance control 10kO Vo max 0kO Vo min 3 External resistance control 10kO Vo min 0kO Vo max Set SYSTem CONFigure MSLave Description Sets
8. GUIfISTEK PSB 1000 Series Programming Manual Common Commands 54 SYSTem CONFigure SENSe STATe SYSTem COMMunicate ENABle eene SYSTem COMMunicate GPIB SELF ADDRess SYSTem COMMunicate LAN IPADd tes SYSTem COMMunicate LAN GA TEway eee SYSTem COMMunicate LAN SMASK es SYSTem COMMunicate LAN MAC eee SYSTem COMMunicate LAN DHCP eese SYSTem COMMunicate LAN DNS iu SYSTem COMMunicate LAN HOS Tname SYSTem COMMunicate LAN WEB PACTive SYSTem COMMunicate LAN WEB PASSword Ses SYSTem COMMunicate RLSTate eene SYSTem COMMunicate USB YFRONECSTATe SYSTem COMMunicate USB REAR STATe SYSTem COMMunicate USB REAR MODPE SYSTem ERRor SYSTem KEYLock MODE n SYSlem KLOQGE nett etcetera e SYSTIem PRESe6t rre ER ERR NE UTR GW INSTEK REMOTE CONTROL Abort Commands ISB OR tis A 55 ABORt Set Description The ABORt command will cancel any triggered actions Syntax ABORt APPLy Commands APPLY eet ttt ttt ttt ttt ttc 55 Set APPLy Description The APPLy command is used to set both the voltage and current The voltage and current will be output as soon as the function is executed if the programmed values are within the accepted range An execution error will occur if the programmed values are not within
9. Parameter BLACK BLUE CYAN GRAY GREEN LIME MAGENTA MAROON NAVY OLIVE PURPLE RED SILVER TEAL WHITE YELLOW Query Syntax DISPlay WINDow TEXT COLor Return parameter lt NRI gt Color 0 BLACK 1 BLUE 2 CYAN 3 GRAY 4 GREEN 5 LIME 6 MAGENTA 7 MAROON 8 NAVY 9 OLIVE 10 PURPLE 11 RED 12 SILVER GW INSTEK REMOTE CONTROL 13 TEAL 14 WHITE 15 YELLOW Example DISP TEXT COL RED Sets the text color to red Set DISPlay WINDow TEXT STATe Description Controls whether the TEXT is visible or not in the user text window Syntax DISPlay WINDow TEXT STATe 0 1 OFF ON Query Sytax DISPlay WINDow TEXT STATe Parameter 0 lt NR1 gt Text is invisible OFF Text is invisible 1 NRI Text is visible ON Text is visible Return parameter 0 NRI Text is visible 1 lt NR1 gt Text is invisible Example DISP TEXT STAT ON Text is set to visible DISPlay WINDow TEXT CLEar Set Description Clears the text on the main screen from the DISPlay WINDow TEXT DATA command Syntax DISPlay WINDow TEXT CLEar 59 GW INSTEK PSB 1000 Series Programming Manual Set DISPlay WINDow TEXT DATA Description Sets or queries the data text that will be written to the display in the user text window Writing to the display will overwrite data that is currently on the screen Overwriting a display area with a shorter string may or may not overwrite the screen The string must be enclosed in quotes
10. RN Speaker disabled b Indicates that the GPIB option is installed and disabled Indicates that the panel lock is active S Indicates that the instrument is connected with a PC Indicates that the panel keys are unlocked p Indicates that a USB flash drive is inserted in the front panel USB port Indicates that a USB flash drive is inserted in the front panel USB port but there is an access error Please re insert BS Indicates that the instrument is connected toa LAN Indicates that the instrument is connected to a LAN however there are configuration errors Please re configure the LAN settings Eam Indicates that the PSB 1000 is in LAN remote mode Indicates that the PSB 1000 is in LAN remote mode but there are connection errors Please re configure the LAN settings 20 GW INSTEK GETTING STARTED Menu Reference Level Function Operation Ist 2nd 3rd 4th Description Main OCP Ctrl Enables Disables OCP OCP Dly Sets OCP delay time Output On Delay Sets the Output On Delay delay time Off Delay Sets the Output Off delay time I V Control CVHS Sets the CV slew rate to the maximum High Speed CCHS Sets the CC slew rate to the maximum High Speed CVLS Sets the CV slew rate CCLS Sets the CC slew rate Exit Exits the I V control menu more 1 of INT R Sets the internal 2 resistance Bleede
11. VISA Run time Engine page or downloads at the following URL http www ni com visa Requirements Firmware V1 12 Operating System Windows XP 7 8 8 1 Functionality check 1 Start the NI Measurement and Automation Explorer MAX program Using Windows press Start gt All Programs gt NI MAX Measurement amp Automation Explorer Initializing Version 5 5 1999 2013 National Instruments All rights reserved 2 From the Configuration panel access My System Devices and Interfaces Network Devices GW INSTEK REMOTE CONTROL 3 Press Add New Network Device gt Visa TCP IP Resource a e Network Devices Measurement amp Automation f File Edit View Tools Help on Syn 3 amp Add Network Device 4 g Devi Iterfaces ii VISA TCP IP A Wi GP Pl IB USB HS E CP IP Resource Hostname Network Devices PX PXI System Unidentified JJ Serial amp Parallel amp Software gt Remote Systems 4 Select Manual Entry of Raw Socket from the popup window Create New VISA TCP IP Resource Measurement i Automation Ex Choose the type of TCF IP resource you wish to edd NATION INSTRUMENTS Auto detect of LAN Instumert m alist of VAT LANL instruments nat Manual Erny of Raw Socket specilic port number 5 Enter the IP address and the port number of the PSB 1000 The port number is fixed at 2268 6 Double c
12. lt NR1 gt Query Sytax DISPlay CONTrast Parameter NRI Description Return parameter 1 to 100 Contrast as a percentage from 1 to 100 56 GW INSTEK REMOTE CONTROL Example DISP CONT 50 Sets the display contrast to 50 Set DISPlay ENABle Description Controls whether the whole display is visible Syntax DISPlay ENABle 0 1 OFF ON Query Sytax DISPlay ENABle Parameter 0 lt NR1 gt Display is invisible OFF Display is invisible 1 lt NR1 gt Display is visible ON Display is visible Return parameter 0 lt NR1 gt Display is visible 1 lt NR1 gt Display is invisible Example DISP ENAB ON Display is visible Set DISPlay WINDow STATe Description Disables or enables the visibility of the user text window Syntax DISPlay WINDow STATe 0 1 OFF ON Query Sytax DISPlay WINDow STATe Parameter 0 lt NR1 gt Window is invisible OFF Window is invisible 1 NR1 Window is visible ON Window is visible Return parameter 0 lt NR1 gt Window is visible 1 NR1 Window is invisible Example DISP ON Enables the display 57 GUIfISTEK PSB 1000 Series Programming Manual DISPlay WINDow TEXT COLor Set Description Sets or returns the color of the user text window Syntax DISPlay WINDow TEXT COLor lt NR1 gt BLACK BLUE CYAN GRAY GREEN LIME MAGENTA MAROON NAVY OLIVE PURPLE RED SILVER TEAL WHITE YELLOW
13. lt NRf gt Step 0 105 of the rated current output level MIN Minimum current level MAX Maximum current level Example SOUR CURR STEP MAX MAX Sets the Step 7 amp Step preset settings to the maximum Set SOURce CURRent STEP RISing Description Sets or returns the preset current Step 7 settings Syntax SOURce CURRent STEP RISing lt NRf gt MIN MAX Query Syntax SOURce CURRent STEP RISing MIN MAX Parameter Return lt NRf 0 105 of the rated current output level MIN Minimum current level MAX Maximum current level Example SOUR CURR STEP RIS MAX Sets the current Step to the maximum Set SOURce CURRent STEP FALLing Description Sets or returns the preset current Step settings Syntax SOURce CURRent STEP FALLing lt NRf gt MIN MAX Query Syntax SOURce CURRent STEP FALLing MIN MAX Parameter Return lt NRf 0 105 of the rated current output level MIN Minimum current level MAX Maximum current level Example SOUR CURR STEP FALL MAX Sets the current Step to the maximum 76 GW INSTEK REMOTE CONTROL SOURce CURRent LEVel TRIGgered Set AMPLitude Description Sets or queries the current level in amps when a software trigger has been generated Syntax SOURce CURRent LEVel TRIGgered AMPLitude NR amp MIN MAX Query Syntax SOURce CURRent LEVel TRIGgered AMPLitude MIN MAX Parameter Return lt NRf 0 105 of the rated
14. 0 1 NRI Integers 0 1 2 3 NR2 Floating point 0 1 3 14 8 5 lt NR3 gt Exponent 4 5e 1 8 25e 1 lt NRf any of NR1 2 3 1 1 5 4 5e 1 lt block data gt Definitive length arbitrary block data A single decimal digit followed by data The decimal digit specifies how many 8 bit data bytes follow Message LF Line feed code Terminator Command List Abort Commands ABORt eese eene entente tette tenens 55 Apply Commands APPLy 9 9 55 Display JDISPlay BRIGBDISS irritare arara a As 56 Commands DISP ay CONTrast PPEP AN E DP PEA E A PE IEEE 1 56 DISPlay ENABle cett ettet sera as Dd DISPlay WINDow STATe eee au DISPlay WINDow TEXT COLot 58 DISPlay WINDow TEX E STATe eeeeett 59 DISPlay WINDow TEXT CLEar DISPlay WINDow TEXT DATA DIS Play BUIN kinnene tat etos Initiate INI Tiate IM Mediate NAME eee 61 Commands 51 GW INSTEK PSB 1000 Series Programming Manual Measure MEASure SCALar CURRent DC UEM Commands MEASute SCALar VOLTage DC Shay MEASure SCALar POWer DC eee Output OUTP DEL ON ap tees tetro erben 63 Commands OU TPutDELay OFF wsscsssccssesscseescsensesstsesstersesstaseasarzeeseas cos 63 OUTPut MODE im EN OUTPut STATe IMMediate ee 64 OUTPut STATe TRIGgered e 64 OU
15. Ethernet interface cse eec 39 Factory settings 125 Front panel diagram 13 Ground Symbol cbe neis 4 List of features 10 Model differences 9 Power on off safety instruction sssss 5 Rear panel diagram 16 128 Remote control Command list Command syntax Error list sss LAN USB Service operation about disassembly 5 Socket server function check 42 UK power cord 7 Warning symbol 4 Web server function check 41
16. L 9 13 PR Program Running 14 14 14 H 1 Not Used 15 15 15 55 107 GU INSTEK PSB 1000 Series Programming Manual Questionable Status Register Group T T STATus QUEStionable CONDition STATus QUEStionable EVENt STATus QUEStionable NTRansition lt NRf gt STATus QUEStionable NTRansition STATus QUEStionable PTRansition lt NRf gt STATus QUEStionable PTRansition STATus QUEStionable ENABle lt NRf gt I STATus QUEStionable ENABle Overview The Questionable Status Register Group indicates if any protection modes or limits have been tripped Questionable Status Register Condition PTR NTP Event Enable OM o 0 0 gt 0 OQ 1 i 0 1 NotUsed 2 2 2 i 2 PO 3 3 3 E 3 oT 4 4 4 8 4 Not Used 5 5 5 to 5 NotUsed 6 6 6 AUN 6 NotUsed 7 7 7 amp 7 V 8 8 8 i EO 8 cu 9 9 9 LL 9 Not Used 10 10 10 l I f 25 10 SD 11 1i 1i LR 11 PU 12 12 12 gt a 12 Not Used 13 gt 18 gt 18 La 18 NotUsed 14 14 gt 14 IL 14 NotUsed 15 15 15 a 4 i I I I I I 1 Y Ie M v ogical Ol To Status Byte Register Bit Summary Bit Event Bit Weight OV Over Voltage 0 1 Over voltag
17. RST Set Description Performs a device reset Configures the unit to a known configuration default settings This known configuration is independent of the usage history Syntax RST Set SRE Description Sets or queries the Service Request Enable register The Service Request Enable register determines which registers of the Status Byte register are able to generate service requests Syntax SRE NR1 Query Syntax SRE Parameter NRI 0 255 Return parameter NRI Returns the bit sum of the Service Request Enable register STB Description Queries the bit sum of the Status Byte register with MSS Master summary Status Query Syntax STB Return parameter NR1 Returns the bit sum of the Status Byte register with the MSS bit bit 6 GW INSTEK REMOTE CONTROL TRG Set Description The TRG command is able to generate a get Group Execute Trigger If the unit cannot accept a trigger at the time of the command an error message is generated 211 Trigger ignored Syntax TRG TST Description Executes a self test Query Syntax TST Return parameter 0 Returns 0 if there are no errors NRI Returns an error code NRI if there is an error WAI Set Description Prevents any other commands or queries from being executed until all outstanding commands have completed Syntax WAI 105 GW INSTEK PSB 1000 Series Programming Manual S
18. Turns the output on ON Turns the output on Return parameter NRI Returns output status of the instrument Set OUTPut STATe TRIGgered Description Turns the output on or off when a software trigger is generated Syntax OUTPut STATe TRIGgered OFF ON 0 1 Query Syntax OUTPut STATe TRIGgered Parameter 0 lt NR1 gt Turns the output off when a software trigger is generated GW INSTEK REMOTE CONTROL OFF Turns the output off when a software trigger is generated 1 lt NR1 gt Turns the output on when a software trigger is generated ON Turns the output on when a software trigger is generated Return parameter NRI Returns output trigger status of the instrument OUTPut PROTection CLEar Set Description Clears over voltage over current and over temperature OVP OCP OTP protection circuits It also clears the shutdown protection circuit The AC failure protection cannot be cleared Syntax OUTPut PROTection CLEar OUTPut PROTection TRIPped Description Returns the state of the protection circuits OVP OCP OTP Query Syntax OUTPut PROTection TRIPped Return parameter 0 lt NR1 gt Protection circuits are not tripped 1 lt NR1 gt Protection circuits are tripped Set OUTPut TRIGger PO Larity Description Sets or returns the polarity of the trigger signal output TRIG OUT Syntax OUTPut TRIGger POLarity 0 1 POSitive NEGative Query Syntax OUTPut TRIGg
19. or queries the unit operation mode This setting is only applied after the unit has been reset Syntax SYSTem CONFigure MSLave 0 1 2 3 4 5 Query Syntax SYSTem CONFigure MSLave Parameter Return NR1 Description 0 Master Local 1 Slave Parallel 2 Slave Series 3 Master Parallel 1 2 units total 4 Master Parallel 2 3 units total 5 Master Parallel 3 4 units total SYSTem CONFigure OUTPut EXTernal Set MODE Description Sets the external logic as active high or active low This setting is only applied after the unit has been reset Syntax SYSTem CONFigure OUTPut EXTernal MODE Query Syntax SYSTem CONFigure OUTPut EXTernal MODE Parameter 0 Active high HIGH Active high 1 Active low LOW Active low Return Parameter 0 boolean Active high 1 boolean Active low 93 GU INSTEK PSB 1000 Series Programming Manual Set SYSTem CONFigure OUTPut PON STATe Description Sets the unit to turn the output ON OFF at power up This setting is only applied after the unit has been reset Syntax SYSTem CONFigure OUTPut PON STATe OFF ON 0 1 Query Syntax SYSTem CONFigure OUTPut PON STATe Parameter 0 Output off at power up OFF Output off at power up 1 Output on at power up ON Output on at power up Return Parameter 0 Output off at power up 1 Output on at power up Set SYSTem CONFigure SENSe STATe Description Sets or returns the sense mode used Syntax SYS
20. polarity of the trigger output can also be configured VOLT TRIG pn Outputs a signal according to the Voltage Trigger settings in the Function menu The polarity of the voltage trigger can also be configured LAN AN The Ethernet port is used for remote control and digital monitoring from a PC hl 17 GUIfISTEK PSB 1000 Series Programming Manual USB B GPIB Option FAN 18 S The USB B port is used for remote control Optional GPIB communication card PSB 105 Temperature controlled fan GUIfISTEK Status Bar Icons Status bar OFF Indicates that the output is in CV mode GETTING STARTED A S99 Indicates if the output is WF An alarm icon will appear on the status bar when one of the protection functions is tripped Indicates that the output is in CC mode Remote sense fail Indicates a problem with the remote sense connection Indicates that the output is operating at 105 of rated power constant power mode Indicates that the unit is in remote mode URS Power fail Indicates that the external shutdown pin was tripped Indicates that the instrument has hardware errors GUIfISTEK PSB 1000 Series Programming Manual d Speaker enabled i Indicates that the GPIB option is installed and enabled
21. the generic query error for devices that cannot detect more specific errors This code indicates only that a Query Error as defined in IEEE 488 2 11 5 1 1 7 and 6 3 has occurred 125 GW INSTEK PSB 1000 Series Programming Manual D ppEN DIX PSB 1000 Default Settings The following default settings are the factory configuration settings for the power supply For details on how to return to the factory default settings see the SYSTem PRESet command on page 101 Function CV Control Local CC Control Local Breaker Enable Ext Out High PON Run None Track Local Sense Disable Speaker Enable Lock Ctrl OFF Output OFF Voltage 0 00V Current 0 00A OVP 10596 Rating OCP 10596 Rating Bleeder Enable INT R 0 0000 Average Low Lock Mode 0 On Delays 0 00s Off Delays 0 00s OCP Control Enable OCP Delays Auto I V Mode CVHS 126 GW INSTEK APPENDIX VSR 7 Maximum VSR V Maximum ISR Z Maximum ISR N Maximum Vdefl 0 00V Vdef2 0 00V Vdef3 0 00V Vsetp 7 0 00V Vsetp v 0 00V OVPdefl 105 Rating OVPdef2 105 Rating OVPdef3 105 Rating 127 GUIfISTEK PSB 1000 Series Programming Manual NDEX Accessories sssseeseeeeee 11 Caution symbol 4 Cleaning the instrument 6 Default settings 125 Disposal instructions 6 EN61010 measurement category 5 pollution degree 6 Environment safety instruction 6
22. 90 o OC OverCurent 1 1 1 H i NotUsed 2 2 2 2 POW AC Power Off 3 3 3 3 OT Over Temperature 4 4 4 4 cup Not Used 5 5 5 5 NotUsed 6 6 6 6 NotUsed 7 7 7 7 VL Voltage Limit 8 8 8 3 CL Current Limit 9 9 9 9 NotUsed 10 10 10 10 Error Que SD Shutdown Alarm 11 1 n n Power Limi 12 12 12 L 9 12 NotUsed 13 13 13 L s NotUsed 14 14 14 L 9 14 Not Used 15 15 15 15 Service Status Request Byte Enable Standard Event Status Register Register Register 0o o Event Enable 1 m OPC Operation Complete 0 0 xa vei j 1 NM 1 ERA 2 2 lequest Control a Loug 3 3 QUE Query Error 2 gt 2 L my 4 L 4 DDE Device Dependent Emon 3 gt 3 i gt esj 5 gt 5 EXE Execution Error 4 L 4 MS 6 4 4 6 CME Command Error 5 5 gt OPER 7 gt 7 URQ User Request 6 9 6 PON PowrOn 7 gt 7 Operation Status Register Condition PTR NTP Event Enable CAL Calibration mode 0 0 0 o NotUsed 1 1 1 p NotUsed 2 2 2 gt 2 NotUsed 3 3 3 e 3 NotUsed 4 4 4 4 WTG Waiting for Trigger 5 5 5 a 5 Not Used 6 6 6 6 NotUsed 7 7 7 7 CV Constant Voltage Model B 8 8 8 NotUsed 9 9 9 9 CC Constant Curent Mode 10 10 10 10 OND Output ON Delay 11 1 4 n OFD Output OFF Delay 12 12 12 12 Not Used 13 13 13
23. As the colours of the wires in main leads may not correspond with the coloured marking identified in your plug appliance proceed as follows The wire which is coloured Green amp Yellow must be connected to the Earth terminal marked with either the letter E the earth symbol or coloured Green Green amp Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Blue or Black The wire which is coloured Brown must be connected to the terminal marked with the letter L or P or coloured Brown or Red If in doubt consult the instructions provided with the equipment or contact the supplier This cable appliance should be protected by a suitably rated and approved HBC mains fuse refer to the rating information on the equipment and or user instructions for details As a guide a cable of 0 75mn should be protected by a 3A or 5A fuse Larger conductors would normally require 13A types depending on the connection method used Any exposed wiring from a cable plug or connection that is engaged in a live socket is extremely hazardous If a cable or plug is deemed hazardous turn off the mains power and remove the cable any fuses and fuse assemblies All hazardous wiring must be immediately destroyed and replaced in accordance to the above standard d GW INSTEK PSB 1000 Series Programming Manual G ETTING STARTED This chapter describes the power source in a nutshel
24. CII characters 20H to 7EH Example SYST COMM LAN SMASk 255 255 0 0 Sets the LAN mask to 255 255 0 0 SYSTem COM Municate LAN MAC Description Returns the unit MAC address as a string The MAC address cannot be changed Query Syntax SYSTem COMMunicate LAN MAC Return parameter lt string gt Returns the MAC address in the following format FF FF FF FF FF FF Example SYST COMM LAN MAC 02 80 AD 20 31 B1 Returns the MAC address Set SYSTem COMMunicate LAN DHCP Description Turns DHCP on off Queries the DHCP status This setting is applied only after the unit is reset Syntax SYSTem COMMunicate LAN DHCP OFF ON 0 1 Query Syntax SYSTem COMMunicate LAN DHCP Parameter 0 DHCP off OFF DHCP off 1 DHCP on ON DHCP on Return parameter 0 boolean DHCP off 1 boolean DHCP on GW INSTEK PSB 1000 Series Programming Manual Set SYSTem COM Municate LAN DNS Description Sets or queries the DNS address This setting is applied only after the unit is reset Syntax SYSTem COMMunicate LAN DNS lt string gt Query Syntax SYSTem COMMunicate LAN DNS Parameter Return lt string gt DNS in string format mask Applicable ASCII characters 20H to 7EH Example SYST COMM LAN DNS 172 16 1 252 Sets the DNS to 172 16 1 252 SYSTem COM Municate _LAN HOSTname Description Queries the host name Query Syntax SYSTem COMMunicate LAN HOSTname Return Parameter lt string gt Host
25. COMMunicate GPIB SELF ADDRess GW INSTEK PSB 1000 Series Programming Manual Parameter Return NRT1 0 30 Example SYST COMM GPIB SELF ADDR 15 Sets the GPIB address to 15 Set SYSTem COMMunicate LAN IPADdress Description Sets or queries LAN IP address This setting is applied only after the unit is reset Syntax SYSTem COMMunicate LAN IPADdress string Query Syntax SYSTem COMMunicate LAN IPADdress Parameter Return lt string gt LAN IP address in string format address Applicable ASCII characters 20H to 7EH Example SYST COMM LAN IPAD 172 16 5 111 Sets the IP address to 172 16 5 111 Set SYSTem COM Municate LAN GATEway Description Sets or queries the Gateway address This setting is applied only after the unit is reset Syntax SYSTem COM Municate LAN GATEway lt string gt Query Syntax SYSTem COMMunicate LAN GATEway Parameter Return lt string gt Gateway address in string format address Applicable ASCII characters 20H to 7EH Example SYST COMM LAN GATE 172 16 0 254 Sets the LAN gateway to 172 16 0 254 96 GW INSTEK REMOTE CONTROL Set SYSTem COMMunicate LAN SMASk Description Sets or queries the LAN subnet mask This setting is applied only after the unit is reset Syntax SYSTem COMMunicate LAN SMASk lt string gt Query Syntax SYSTem COMMunicate LAN SMASk Parameter Return lt string gt Subnet mask in string format mask Applicable AS
26. E CONTROL 222 Data out of Indicates that a legal program data element was range parsed but could not be executed because the interpreted value was outside the legal range as defined by the device see IEEE 488 2 11 5 1 1 5 224 Illegal Used where exact value from a list of possibles parameter value was expected Device Specific Errors Overview An lt error event number gt in the range 399 300 or 1 32767 indicates that the instrument has detected an error which is not a command error a query error or an execution error some device operations did not properly complete possibly due to an abnormal hardware or firmware condition These codes are also used for self test response errors The occurrence of any error in this class should cause the device specific error bit bit 3 in the event status register IEEE 488 2 section 11 5 1 to be set The meaning of positive error codes is device dependent and may be enumerated or bit mapped the lt error message gt string for positive error codes is not defined by SCPI and available to the device designer Note that the string is not optional if the designer does not wish to implement a string for a particular error the null string should be sent for example 42 The occurrence of any error in this class should cause the device specific error bit bit 3 in the event status register IEEE 488 2 section 11 5 1 to be set Events that generate device spec
27. IB 4 To clear the selected log from the screen press F4 Clear OFF Pr CE 1 0 No error Error log Log source Exit 5 Press Exit F5 to exit from the Error Log screen 47 GW INSTEK PSB 1000 Series Programming Manual Command Syntax IEEE488 2 Partial compatibility Compatible Standard SCPI 1999 Partial compatibility Command SCPI commands follow a tree like structure Structure organized into nodes Each level of the command tree is a node Each keyword in a SCPI command represents each node in the command tree Each keyword node of a SCPI command is separated by a colon For example the diagram below shows an SCPI sub structure and a command example MEASure MEASure SCALar CURRent DC SCALar clum VOLTage CURRent POWer DC DC DC Command types There are a number of different instrument commands and queries A command sends instructions or data to the unit and a query receives data or status information from the unit Command types Simple A single command with without a parameter Example IDN amp GUIfISTEK REMOTE CONTROL Query Example A query is a simple or compound command followed by a question mark A parameter data is returned meas curr dc Compound Example Two or more commands on the same command line Compound commands are separated with either a semi colon or a semi colon and a colon
28. INSTEK PSB 1900M 0000 70 70 20150506a 12 The function check is complete 38 GW INSTEK REMOTE CONTROL Configure Ethernet Connection The Ethernet interface can be configured for a number of different applications Ethernet can be configured for basic remote control or monitoring using a web server or it can be configured as a socket server The PSB 1000 supports both DHCP connections so the instrument can be automatically connected to an existing network or alternatively network settings can be manually configured Ethernet MAC Address display Host Name display only Parameters only LAN Control DHCP IP Address Subnet Mask Gateway DNS Server Socket Control Socket port fixed 2268 Web Control Password Control Web Password Ethernet 1 Connect a LAN cable from the PC LAN Configuration to the Ethernet port on the rear panel LJ 2 Press the Utility key The Utility menu will appear on the display 3 Go to the Interface gt gt gt setting using the scroll wheel and press Enter 4 Use the scroll wheel to go to the LAN setting and press Enter 5 If the LAN cable is installed correctly a LAN icon will appear in the status bar 39 GW INSTEK PSB 1000 Series Programming Manual 6 To automatically have the network assign an IP address set DHCP to ON Otherwise set DHCP to OFF to manually set the Ethernet settings DHC
29. Multi Range DC Power Supply PSB 1000 Series PROGRAMMING MANUAL VERSION 1 0 1SO 9001 CERTIFIED MANUFACTURER finn GW INSTEK This manual contains proprietary information which is protected by copyright All rights are reserved No part of this manual may be photocopied reproduced or translated to another language without prior written consent of Good Will company The information in this manual was correct at the time of printing However Good Will continues to improve products and reserves the rights to change specification equipment and maintenance procedures at any time without notice Good Will Instrument Co Ltd No 7 1 Jhongsing Rd Tucheng Dist New Taipei City 236 Taiwan GW INSTEK Table of Contents Table of Contents SAFETY INSTRUCTIONS 4 sscessnsentessrrcseanesscvavsvesanocsnsseonenenss 4 GETTING STARTED sictstassscoctsasscwasiunsecersevetensteesnentaednesnseiese 8 PSB 1000 Series Overview 9 Appearances etenin iaeiae 13 REMOTE CONTROL 2er xx sensencecon s 27 Interface Configuration 28 Command SyntaX seser 48 Command List Leeser 51 Status Register Overview 106 Error LIST Lees eterno rite regere onere 117 APPENDIX eer 126 PSB 1000 Default Settings 126 l biz Ce 128 GW INSTEK PSB 1000 Series Programming Manual SAFETY INSTRUCTIONS This chapter contai
30. P ON OFF 7 If DHCP was set to OFF configure the remaining LAN parameters LAN Control IP Address Subnet Mask Gateway DNS Server Socket control Socket port fixed 2268 Web control Password control Web password Connection status IP Address Subnet Mask 255 255 128 0 LAN settings Gateway 172 16 0 254 DNS Server 172 16 1 252 onde Exit 8 Press Exit F5 to exit from the LAN settings GW INSTEK REMOTE CONTROL Web Server Remote Control Function Check Enter the IP address of the power supply for Functionality example http XXX XXX XXX XXX in a web check browser after the instrument has been configured for LAN page 39 The web interface allows you to eView the system and information and the network configuration View the analog control pinout View the dimensions of the unit View the operating area Example Ww Gw INSTEK Visit Our Site Support Countact Us Made to Measure Network Configration Werome Page z DNS Network Configration Gatew Analog Control DSO SECH ON 9 OFF E Submit Operating Area 41 GW INSTEK PSB 1000 Series Programming Manual Socket Server Function Check Background To test the socket server functionality National Instruments Measurement and Automation Explorer can be used This program is available on the NI website www ni com via a search for the
31. Programming Manual Status Commands STATus OPERation FEVENY eee 70 STATus OPERation CONDiition eene 70 STATus OPERation EN ABle s STATus OPERation PTRansition eene 71 STATus OPERation NTRansition eee 71 STATus QUEStionable EVENt STATus QUEStionable CONDition STATus QUEStionable ENABBle eese STATus QUEStionable PTRansition ii STATus QUEStionable N TRansition ess 72 SLA Tus PRES Efesus oni nsen pira 73 STATus OPERation EVENt Description Queries the Operation Status Event register and clears the contents of the register Syntax STATus OPERation EVENt Return NRI Returns the bit sum of the Operation Status Event register STATus OPERation CONDition Query Description Queries the Operation Status register This query will not clear the register Syntax STATus OPERation CONDition Return NRI Returns the bit sum of the Operation Condition register Set STATus OPERation ENABle Description Sets or queries the bit sum of the Operation Status Enable register 70 GW INSTEK REMOTE CONTROL Syntax STATus OPERation ENABle lt NRf gt Query Syntax STATus OPERation ENABle Parameter NRf 0 32767 Return parameter NR1 0 32767 Set STATus OPERation PTRansition Description Sets or queries the bit sum of the positive transition filt
32. SS Bit 6 64 The MSS Bit is the summary of the Status Byte Register and Service Request register bits 1 5 7 This will be set to 1 OPER Operation Status Register 7 128 OPER bit is the summary bit for the Operation Status Register Group Status Byte Any bits set in the Status byte register acts as a Register summary register for all the three other status registers and indicates if there is a service request an error in the Error Queue or data in the Output Queue Reading the Status Byte register will reset the register to 0 Service Request The Service Request Enable Register controls Enable Register which bits in the Status Byte Register are able to generate service requests 116 GW INSTEK REMOTE CONTROL Error List Gonituand EttOfsu e imt rir HIRED Ir odd Execution Errors Device Specific Errors s Query Brtots scoot aaa Command Errors Overview An lt error event number in the range 199 100 indicates that an IEEE 488 2 syntax error has been detected by the instrument s parser The occurrence of any error in this class shall cause the command error bit bit 5 in the event status register IEEE 488 2 section 11 5 1 to be set One of the following events has occurred e An IEEE 488 2 syntax error has been detected by the parser That is a controller to device message was received which is in violation of the IEEE 488 2 standard Possible violations inclu
33. Swotd SYSTem COMMunicate RLSTate eeeeeennnee SYSTem COMMunicate USB FRONt STATe SYSTem COMMunicate USB REAR STATe SYSTem COMMunicate USB REAR MODPE SYSTem ERRor SYSTem KEYLock MODBEE eee SYsTem KEGOGCk eiie riter er nni SYSTem PRESet SYSTem VERSion 89 GW INSTEK PSB 1000 Series Programming Manual Set SYSTem BEEPer IMMediate Description This command causes an audible tone to be generated by the instrument The duration time is specified in seconds Syntax SYSTem BEEPer IMMediate lt NR1 gt MINimum MAXimum Query Syntax SYSTem BEEPer IMMediate MINimum MAXimum Parameter NRI 0 3600 seconds MINimum Sets the beeper time to the minimum 0 seconds MAXimum Sets the beeper time to the maximum 3600 seconds Return parameter lt NR1 gt Returns the remaining beeper duration time in seconds or returns the maximum or minimum beeper time in seconds for the MINimum MAXimum query parameters Example 1 SYST BEEP 10 after a 2 second wait SYST BEEP gt 8 The first command turns the beeper on for 10 seconds After 2 seconds the SYST BEEP query returns the remaining beeper time 8 seconds Example 2 SYST BEEP MAX gt 3600 Returns the maximum settable beeper time in seconds Set SYSTem CON Figure BEEPer STATe Description Sets or queries the buzzer state on o
34. Syntax SOURce CURRent SLEW FALLing lt NRf MIN MAX Query Syntax SOURce CURRent SLEW FALLing MIN MAX Parameter Return NRf 0 01 rating current x 2 MIN Minimum falling current slew rate MAX Maximum falling current slew rate Example SOUR CURR SLEW FALL 1 Sets the falling current slew rate to 1A s SOURce RESistance LEVel IM Mediate Set AMPLitude Description Sets or queries the internal resistance in ohms Syntax SOURce RESistance LEVel IMMediate AM PLitude lt NRf amp MIN DEF MAX Query Syntax SOURce RESistance LEVel IMMediate AM PLitude gt MIN MAX Parameter Return lt NRf gt Resistance in ohms 0 0002 1 0002 PSB 1400L 0 0002 16 002 PSB 1400M 0 0002 0 500 PSB 1800L 0 00022 8 00022 PSB 1800M MIN Minimum internal resistance in ohms MAX Maximum internal resistance in ohms Example SOUR RES LEV IMM AMPL 0 1 Sets the internal resistance to 100mQ SOURce VOLTage LEVel IM Mediate Set AMPLitude Description Sets or queries the voltage level in volts Syntax SOURce VOLTage LEVel IMMediate AM PLitude lt NRf gt MIN MAX DEF1 DEF2 DEF3 Query Syntax SOURce VOLTage LEVel 1 M Mediate AM PLitude MIN MAX DEF1 DEF2 DEF3 80 GW INSTEK REMOTE CONTROL Parameter Return lt NRf gt 0 105 of the rated output voltage in volts MIN Minimum voltage level MAX Maximum voltage level DEFI User defined setting 1 DEF2 User defined settin
35. TPut PROTection CLEar ee ees OUTPut PROTection TRIP pedreres 65 OUTPut TRI Gger POLati tynnir OUTPut VTRigger CONTrol Sess OUT Put VT Rigger POLArity eee OUT Put VT Rigger S TA Tee vsssssssssssstsssststesvorastessssaresansssaness 66 OUTPut VI Rigger VES 1 22i tetti 67 Input Commands INPut TRIGger POLarity duu hengivanscavenianeng E PRINTERS nS 68 Sense SENSe AVERage COUNt 5333595039005025 13390022 0039909 399 003 08 0 08008 ss 69 Commands Status STATus OPERation EVENt 70 Commands STATus OPERation CONDiton 70 STATus OPERation ENABle 70 STATus OPERation PTRansition aed STATus OPERation NTRansition el STATus QUEStionable EVENEtE A STATus QUEStionable CONDition wl STATus QUEStonable ENABle eee STATus QUEStionable PTRansition fA STATus QUEStionable N TRansition sd STA Tus BRESGE cr pct EPOR UR ERE Reda 73 52 GW INSTEK REMOTE CONTROL Source SOURce CURRent LEVel MMediate AMPLitude 74 Commands SOURce CURRent DEF lt 1 2 3 gt sessssee 15 SOURce CURRentS TBP sprays 75 SOURce CURRentcS TEP RISing eee 76 SOURce CURRentcS TEP FALLing eee 76 SOURce CURRent LEVel TRIGgered AMPLitude 77 SOURce CURRent PROTection LEVel T SOURce CURRent PROTection DEF lt 1 2 32 78 SOURce CURRent PROTectio
36. Tem CONFigure SENSe STATe 0 1 2 DISable REAR FRONt Query Syntax SYSTem CONFigure SENSe STATe Parameter O DISable Disables remote sense 1 REAR Sets remote sense to the rear panel terminals 2 FRONt Sets remote sense to the front panel terminals Return parameter NR1 Returns the sense mode Example SYST CONF SENS 0 Disables remote sense GW INSTEK REMOTE CONTROL Set SYSTem COMMunicate ENABle Description Enables Disables LAN GPIB or USB remote interfaces as well as remote services Sockets Web Server This setting is applied only after the unit is reset Syntax SYSTem COMMunicate ENABle lt mode gt lt interface gt Query Syntax SYSTem COMMunicate ENABle lt interface gt Parameter lt mode gt OFF Turns the selected mode off 0 Turns the selected mode off ON Turns the selected mode on 1 Turns the selected mode on interface GPIB Select GPIB USB Select USB LAN Select LAN SOCKets Select Sockets WEB Select the web server Return Parameter 0 The selected mode is off 1 The selected mode is on Example SYST COMM ENAB 1 USB Turns the USB interface on Query Example SYST COMM ENAB USB 1 Queries the USB state returns 1 USB is on SYSTem COMMunicate GPIB SELF ADDR ess Description Sets or queries the GPIB address This setting is applied only after the unit is reset Syntax SYSTem COMMunicate GPIB SELF ADDRess lt NR1 gt Query Syntax SYSTem
37. Time in seconds for turning the output on The delay is set to 0 00 by default Syntax OUTPut DELay ON lt NRf gt Query Syntax OUTPut DELay ON Parameter lt NRf 0 00 100 00 seconds where 0 no delay Return parameter lt NRf gt Returns the delay on time in seconds until the output is turned on Set OUTPut DELay OFF Description Sets the Delay Time in seconds for turning the output off The delay is set to 0 00 by default Syntax OUTPut DELay OFF lt NRf gt Return Syntax OUTPut DELay OFF Parameter lt NRf gt _0 00 100 00 seconds where 0 no delay Return parameter lt NRf gt Returns the delay off time in seconds until the output is turned off 63 GW INSTEK PSB 1000 Series Programming Manual Set OUTPut MODE Description Sets or returns the slew rate control settings Syntax OUTPut MODE lt NR1 gt CVHS CCHS CVLS CCLS Return Syntax OUTPut MODE Parameter 0 CV high speed priority CVHS CV high speed priority 1 CC high speed priority CCHS CC high speed priority 2 CV slow speed priority CVLS CV slow speed priority 3 CC slow speed priority CCLS CC slow speed priority Return parameter NR1 Returns the output mode Set OUTPut STATe IM Mediate Description Turns the output on or off Syntax OUTPut STATe IMMediate OFF ON 0 1 Query Syntax OUTPut STATe IMMediate Parameter 0 lt NR1 gt Turns the output off OFF Turns the output off 1 lt NR1 gt
38. accepted ranges Syntax APPLy lt voltage gt MIN MAX lt current gt MIN MAX Query Syntax APPLy Parameter voltage NRf 0 105 of the rated output voltage current NRf 0 105 of the rated output current MIN 0 volts 0 amps MAX Maximum value for the present range Return parameter lt NRf gt Returns the voltage and current Example APPL 5 05 1 1 Sets the voltage and current to 5 05V and 1 1A 5 ui GW INSTEK PSB 1000 Series Programming Manual Query Example APPL 5 050 1 100 Returns voltage 5 05V and current 1 1A setting Display Commands DISPlay BRIGhtness 55 tint ete totes tips 56 DISPlay CONTrast aa 2456 DISPlay ENABle T 57 DISPlay WINDow STATe 457 DISPlay WINDow TEXT COLor 58 DISPlay WINDow TEXT STATe 5459 DISPlay WINDow TEXT CLEar 59 DISPlay WINDow TEXT DATA 60 DISPlay BELNE aceite a a cn er E pee eher peas 60 Set DISPlay BRIGhtness Description Controls the brightness of the display as a percentage Syntax DISPlay BRIGhtness NRT Query Sytax DISPlay BRIGhtness Parameter NRI Description Return parameter to 100 Brightness as a percentage from 1 to 100 Example DISP BRIG 50 Sets the display brightness to 5096 Set DISPlay CONTrast Description Controls the contrast level of the display as a percentage Syntax DISPlay CONTrast
39. alid character for the data type being parsed was encountered for example an alpha in a decimal numeric or a 9 in octal data A legal numeric data element was received but the device does not accept one in this position for the header The suffix does not follow the syntax described in IEEE 488 2 7 7 3 2 or the suffix is inappropriate for this device 119 GUIfISTEK PSB 1000 Series Programming Manual 141 Invalid character data 148 Character data not allowed 151 Invalid string data 158 String data not allowed 160 Block data error 161 Invalid block data 168 Block data not allowed 178 Expression data not allowed 120 Either the character data element contains an invalid character or the particular element received is not valid for the header A legal character data element was encountered where prohibited by the device A string data element was expected but was invalid for some reason see IEEE 488 2 7 7 5 2 for example an END message was received before the terminal quote character A string data element was encountered but was not allowed by the device at this point in parsing This error as well as errors 161 through 169 are generated when parsing a block data element This particular error message should be used if the device cannot detect a more specific error A block data element was expected but was invalid for some reason see IEEE 488 2 7 7 6 2 for ex
40. alterm website 2 Connect the PSB 1000 via USB page 28 3 Go to the Windows device manager and find the COM port number for the connection For example go to the Start menu gt Control Panel gt Hardware and Sound gt Device Manager Double click the Ports icon to reveal the connected serial port devices and the COM port for the each connected device When using USB the baud rate stop bit and parity settings can be viewed by right clicking the connected device and selecting the Properties option GW INSTEK PSB 1000 Series Programming Manual V Portable Devices 4 I Ports COM amp LPT he PSB Faaa D Processo Update Driver Software gt Smart ca Disable Sound vi Uninstall WM System d Scan for hardware changes Universal Properties 4 Start Realterm on the PC as an administrator Click Start menu All Programs RealTerm realterm Tip to run as an administrator you can right click the Realterm icon in the Windows Start menu and select the Run as Administrator option 5 After Realterm has started click on the Port tab Enter the Baud Parity Data bits Stop bits and Port number configuration for the connection as shown in the Device Manager The Hardware Flow Control Software Flow Control options can be left at the default settings Press Open to connect to the PSB 1000 32 GW INSTEK REMOTE CONTROL 29 RealTerm Serial Capture Program 2 0 0 70 Di
41. ample an END message was received before the length was satisfied A legal block data element was encountered but was not allowed by the device at this point in parsing A legal expression data was encountered but was not allowed by the device at this point in parsing GW INSTEK REMOTE CONTROL Execution Errors Overview An lt error event number in the range 299 200 indicates that an error has been detected by the instrument s execution control block The occurrence of any error in this class shall cause the execution error bit bit 4 in the event status register IEEE 488 2 section 11 5 1 to be set One of the following events has occurred e A PROGRAM DATA element following a header was evaluated by the device as outside of its legal input range or is otherwise inconsistent with the device s capabilities e A valid program message could not be properly executed due to some device condition Execution errors shall be reported by the device after rounding and expression evaluation operations have taken place Rounding a numeric data element for example shall not be reported as an execution error Events that generate execution errors shall not generate Command Errors device specific errors or Query Errors see the other error definitions in this section Error Code Description 200 Execution This is the generic syntax error for devices that error cannot detect more specific errors This code i
42. ansition filter of the Questionable Status register Syntax STATus QUEStionable PTRansition lt NRf amp Return Syntax STATus QUEStionable PTRansition Parameter NRf 0 832767 Return parameter NR1 0 32767 Set STATus QUEStionable NTRansition Description Sets or queries the negative transition filter of the Questionable Status register Syntax STATus QUEStionable NTRansition lt NRf gt Query Syntax STATus QUEStionable NTRansition 72 GW INSTEK REMOTE CONTROL Parameter lt NRf 0 32767 Return parameter NRI 0 32767 STATus PRESet Set Description This command resets the ENABle register the PTRansistion filter and NTRansistion filter on the Operation Status and Questionable Status Registers The registers filters will be reset to a default value Default Register Filter Values Setting QUEStionable Status Enable 0x0000 QUEStionable Status Positive Transition Ox7FFF QUEStionable Status Negative Transition 0x0000 Operation Status Enable 0x0000 Operation Status Positive Transition Ox7FFF Operation Status Negative Transition 0x0000 Summary The Questionable Status Enable registers and the Operation Status Enable registers are both reset to 0 The Questionable Status and Operation Status Positive Transition filters are all set high 0x7FFF and the Negative Transition filters are all set low 0x0000 Le only positive transitions will be recognized for the Questionable Status and Operation Sta
43. ctor the set current level is returned Syntax SOURce CURRent LEVel I M Mediate AM PLitude lt NRf gt MIN MAX DEF1 DEF2 DEF3 Query Syntax SOURce CURRent LEVel 1MMediate AMPLitude MIN MAX DEF1 DEF2 DEF3 74 GW INSTEK REMOTE CONTROL Parameter Return lt NRf gt 0 105 of the rated current output level MIN Minimum current level MAX Maximum current level DEFI User defined setting 1 DEF2 User defined setting 2 DEF3 User defined setting 3 Example SOUR CURR LEV IMM AMPL MAX 37 800 Returns the maximum possible current level in amps Set SOURce CURRent DEF lt 1 2 3 gt Description Sets or returns the current of the user defined settings Syntax SOURce CURRent DEF lt 1 2 3 gt lt NRf gt MIN MAX Query Syntax SOURce CURRent DEF lt 1 2 3 gt MIN MAX Parameter Return 1 DEF1 2 DEF2 3 DEF3 lt NRf 0 105 of the rated current output level MIN Minimum current level MAX Maximum current level Example SOUR CURR DEF1 MAX Sets the DEF to the maximum current level Set SOURce CURRent STEP Description Sets or returns the current Step amp Step preset settings Syntax SOURce CURRent STEP lt rise gt MIN MAX lt fall gt MIN MAX Query Syntax SOURce CURRent STEP MIN MAX 75 GW INSTEK PSB 1000 Series Programming Manual Parameter Return rise lt NRf gt Step Z 0 105 of the rated current output level lt fall gt
44. current output in amps MIN Minimum current level MAX Maximum current level Example SOUR CURR LEV TRIG AMPL MAX 37 800 Returns the maximum possible current level in amps Set SOURce CURRent PROTection LEVel Description Sets or queries the OCP over current protection level in amps Syntax SOURce CURRent PROTection LEVel NR amp MIN MAX DEFT DEF2 DEF3 Query Syntax SOURce CURRent PROTection LEVel MIN MAX DEF1 DEF2 DEF3 Parameter Return lt NRf 4 44A 1400L 1 11A 1400M 5 88A 1800L 2 22A 1800M MIN Minimum OCP level MAX Maximum OCP level DEFI User defined setting 1 DEF2 User defined setting 2 DEF3 User defined setting 3 GUIfISTEK PSB 1000 Series Programming Manual Example SOUR CURR PROT LEV MIN 3 600 Returns the minimum possible current level in amps SOURce CURRent PROTection Set DEF lt 1 2 3 gt Description Sets or returns the user defined over current protection settings Syntax SOURce CURRent PROTection DEF lt 1 2 3 gt lt NRfS MIN MAX Query Syntax SOURce CURRent PROTection DEF lt 1 2 3 gt MIN MAX Parameter Return 1 DEF1 2 DEF2 3 DEF3 lt NRf amp 4 44A 1400L 1 11A 1400M 5 88A 1800L 2 22A 1800M MIN Minimum OCP level MAX Maximum OCP level Example SOUR CURR PROT DEF1 MIN Sets DEF1 to the minimum OCP level SOURce CURRent PROTection DELay Set TIME Description Sets or returns the OCP delay time Syn
45. d voltage output level MIN Minimum voltage level MAX Maximum voltage level Example SOUR VOLT STEP RIS MAX Sets the voltage Step to the maximum Set SOURce VOLTage STEP FALLing Description Sets or returns the preset voltage Step settings Syntax SOURce VOLTage STEP FALLing lt NRf gt MIN MAX Query Syntax SOURce VOLTage STEP FALLing MIN MAX Parameter Return lt NRf 0 105 of the rated voltage output level MIN Minimum voltage level MAX Maximum voltage level Example SOUR VOLT STEP FALL MAX Sets the voltage Step to the maximum 82 GW INSTEK REMOTE CONTROL SOURce VOLTage LEVel TRIGgered Set AMPLitude Description Sets or queries the voltage level in volts when a software trigger has been generated Syntax SOURce VOLTage LEVel TRIGgered AMPLitude lt NRf gt MIN MAX Query Syntax SOURce VOLTage LEVel TRIGgered AMPLitude MIN MAX Parameter Return lt NRf gt 0 105 of the rated voltage output in volts MIN Minimum current level MAX Maximum current level Example SOUR VOLT LEV TRIG AMPL 10 Sets the voltage level to 10 volts when a software trigger is generated Set SOURce VOLTage PROTection LEVel Description Sets or queries the overvoltage protection level Syntax SOURce VOLTage PROTection LEVel lt NRf gt MIN MAX DEF1 DEF2 DEF3 Query Syntax SOURce VOLTage PROTection LEVel MIN MAX DEF1 DEF2 DEF3 Parameter Re
46. de g GW INSTEK REMOTE CONTROL Syntax SOURce VOLTage SLEW FALLing lt NRf gt MIN MAX Query Syntax SOURce VOLTage SLEW FALLing MIN MAX Parameter Return lt NRf gt 0 01 rating voltage x 2 MIN Minimum voltage falling slew rate MAX Maximum voltage falling slew rate Example SOUR VOLT SLEW FALL MIN Sets the falling voltage slew rate to its minimum 85 GW INSTEK PSB 1000 Series Programming Manual Trigger Commands The trigger commands generate and configure software triggers TRIGger TRANsient IMMediate eee 86 TRIGgetr TRANsientSOURCce eee 86 TRIGger OUTPut IM Mediate eee 87 TRIGger OUTPut SOURCe nrti teintes tti obo atout ebd 87 Trigger Command Examples see 87 TRIGger TRANsient IM Mediate Sei Description Generates a software trigger for the transient trigger system On a trigger sets the voltage amp current Refer to the CURR TRIG and VOLT TRIG commands on page 77 and 83 respectively Syntax TRIGger TRANsient I M Mediate Related SOURce CURRent LEVel TRIGgered AMPLitude Commands SOURce VOLTage LEVel TRIGgered AMPLitude Set TRIGger TRANsient SOURce Description Sets or queries the trigger source for the transient system Syntax TRIGger TRANsient SOURce BUS IMMediate Query Syntax TRIGger TRANsient SOURce Parameter Return BUS Internal software trigger Waits for
47. de a data element which violates the device listening formats or whose type is unacceptable to the device e An unrecognized header was received Unrecognized headers include incorrect device specific headers and incorrect or unimplemented IEEE 488 2 common commands Events that generate command errors shall not generate execution errors device specific errors or query errors see the other error definitions in this chapter 117 GU INSTEK PSB 1000 Series Programming Manual Error Code 100 Command Error 102 Syntax error 103 Invalid separator 104 Data type error 108 Parameter not allowed 109 Missing parameter 111 Header separator error 118 Description This is the generic syntax error for devices that cannot detect more specific errors This code indicates only that a Command Error as defined in IEEE 488 2 11 5 1 1 4 has occurred An unrecognized command or data type was encountered for example a string was received when the device does not accept strings The parser was expecting a separator and encountered an illegal character for example the semicolon was omitted after a program message unit MEAS VOLT DC MEASCURR DC The parser recognized a data element different than one allowed for example numeric or string data was expected but block data was encountered More parameters were received than expected for the header for example the KLOCk command only accepts one pa
48. e MAV bit in the Status Byte Register is also cleared Syntax CLS Set ESE Description Sets or queries the Standard Event Status Enable register Syntax ESE lt NRI gt Query Syntax ESE Parameter NRI 0 255 Return parameter NR1 Returns the bit sum of the Standard Event Status Enable register 102 GW INSTEK REMOTE CONTROL ESR Description Queries the Standard Event Status Event register The Event Status register is cleared after it is read Query Syntax ESR Return parameter NR1 Returns the bit sum of the Standard Event Status Event register and clears the register IDN Description Queries the manufacturer model name serial number and software version of the unit Query Syntax IDN Return parameter lt string gt Returns the instrument identification as a string in the following format GW INSTEK PSB 1400L TWXXXXXXXXXX X XX XXXXXXXX Manufacturer GW INSTEK Model number PSB 1400L Serial number TWXXXXXXXXXX Software version X XX XXXXXXXX Set OPC Description The OPC command sets the OPC bit bitO of the Standard Event Status Register when all current commands have been processed The OPC Query returns 1 when all the outstanding commands have completed Syntax OPC Query Syntax OPC Return parameter 1 Returns 1 when all the outstanding commands have completed 103 GW INSTEK PSB 1000 Series Programming Manual
49. e protection has been tripped OC Over Current 1 2 Over current protection has been tripped POW AC Power Off 3 8 AC power switch is off GW INSTEK REMOTE CONTROL OT Over Temperature 4 16 Over temperature protection has been tripped VL Voltage Limit 8 256 Voltage limit has been reached CL Current Limit 9 512 Current limit has been reached SD Shutdown Alarm 11 2048 PL Power Limit 12 4096 Condition The Questionable Status Condition Register Register indicates the status of the power supply If a bit is set in the Condition register it indicates that the event is true Reading the condition register does not change the state of the condition register PTR NTR Filters The PTR NTR Positive Negative transition register determines the type of transition conditions that will set the corresponding bit in the Event Registers Use the Positive transition filter to view events that change from false to positive and use the negative transition filter to view events that change from positive to negative Positive Transition 021 Negative Transition 10 Event Register The PTR NTR Register will dictate the type of transition conditions will set the corresponding bits in the Event Register If the Event Register is read it will be cleared to 0 Enable Register The Enable register determines which Events in the Event Register will be used to set the QUES bit in the Status Byte Registe
50. e used for remote control Please see the user manual for installation details GPIB 1 Connect a GPIB cable from the PC 35 3 Fo Configuration to the GPIB on the interface card 2 Press the Utility key The Utility menu will appear on the display 3 Go to the Interface gt gt gt setting using the scroll wheel and press Enter 4 Use the scroll wheel to go to the GPIB setting and press Enter 5 Go to the GPIB Control setting and select Enable 34 GUIfISTEK REMOTE CONTROL Kel Exit GPIB Control Disable Enable Goto the GPIB Address key in the address using the keypad and then press Enter GPIB Address 0 30 Press the F4 Save soft key to save the GPIB settings The GPIB icon will appear in the status bar to indicate that the GPIB connection is enabled Connection status GPIB Control GPIB setting GPIB Address 8 elle Press Exit F5 to exit from the GPIB settings GPIB constraints eMaximum 15 devices altogether 20m cable length 2m between each device eUnique address assigned to each device eAt least 2 3 of the devices turned On No loop or parallel connection 35 GW INSTEK PSB 1000 Series Programming Manual GPIB Function Check Please use the National Instruments Measurement Functionality amp Automation Controller software to confirm check GPIB LAN functionality See the National Instrum
51. ent website http www ni com for details AN For further details please see the programming Note manual available on the GW Instek web site www gwinstek com Operation 1 Start the NI Measurement and ex Automation Explorer MAX program Using Windows press Start All Programs NI MAX Measurement amp Automation Explorer Initializing Version 5 5 1999 2013 National Instruments Alll rights reserved 2 From the Configuration panel access My System gt Devices and Interfaces gt GPIBO GW INSTEK REMOTE CONTROL 3 Press the Scan for Instruments button 4 In the Connected Instruments panel the PSB 1000 should be detected as Instrument 0 with the address the same as that configured on the PSB 1000 5 Double click the Instrument 0 icon 6 Click on Visa Properties 7 Click on Open Visa Test Panel 8 Click on the Input Output icon 9 Under the Basic I O tab ensure IDN is written in the Select or Enter Command text box 10 Click on the Query button to send the IDN query to the instrument 37 GW INSTEK PSB 1000 Series Programming Manual 11 The instrument identification string will be returned to the buffer area GW_INSTEK PSB 1400L TWXXXXXXXXXX X XX XXXXXXXX manufacturer model serial number software version 3 crso a iNsTR 8 mh OS EO Bytes to Read E Quer end Rad Stat Byte ed ASCILvexadecima GW
52. er POLarity Parameter 0 lt NR1 gt Positive polarity POSitive Positive polarity 1 lt NR1 gt Negative polarity NEGative Negative polarity 65 GW INSTEK PSB 1000 Series Programming Manual Return parameter lt NR1 gt Returns the polarity of the trigger signal output TRIG OUT Set OUTPut VTRigger CONTrol Description Sets or returns the voltage trigger output control settings VOLT TRIG Syntax OUTPut VTRigger CONTrol 0 1 DISable ENABle Query Syntax OUTPut VTRigger CONTrol Parameter 0 NRI Disable DISable Disable 1 lt NR1 gt Enable ENABle X Enable Return parameter lt NR1 gt Returns the voltage trigger output control settings VOLT TRIG Set OUTPut VTRigger POLarity Description Sets or returns the polarity of voltage trigger output VOLT TRIG Syntax OUTPut VTRigger POLarity 0 1 POSitive NEGative Query Syntax OUTPut VTRigger POLarity Parameter 0 NRI Positive POSitive Positive 1 NR1 Negative NEGative Negative Return parameter lt NR1 gt Returns the polarity of the voltage trigger output VOLT TRIG OUTPut VTRigger STATe Query Description Returns the state of the voltage trigger output VOLT TRIG Query Syntax OUTPut VTRigger STATe 66 GW INSTEK REMOTE CONTROL Return parameter 0 NRI2LOW 1 lt NR1 gt HIGH Set OUTPut VTRigger VT 1 2 Description Sets or returns the Vt1 or Vt2 setting of the voltage t
53. er of the Operation Status register Syntax STATus OPERation PTRansition lt NRf gt STATus OPERation PTRansition Parameter NRf 0 32767 Return parameter NR1 0 32767 Set STATus OPERation NTRansition Description Sets or queries the bit sum of the negative transition filter of the Operation Status register Syntax STATus OPERation NTRansition lt NRf gt Query Syntax STATus OPERation NTRansition Parameter lt NRf 0 32767 Return parameter NRI 0 32767 STATus QUEStionable EVENt Description Queries the bit sum of the Questionable Status Event register This query will also clear the contents of the register Query Syntax STATus QUEStionable EVENt Parameter lt NRf gt 0 32767 Return parameter NRI 0 32767 7 GW INSTEK PSB 1000 Series Programming Manual STATus QUEStionable CONDition Description Queries the status bit sum of the Questionable Status register This query will not clear the register Query Syntax STATus QUEStionable CONDition Parameter NRf 0 32767 Return parameter NR1 0 32767 Set STATus QUEStionable ENABle Description Sets or queries the bit sum of the Questionable Status Enable register Syntax STATus QUEStionable ENABle lt NRf gt Query Syntax STATus QUEStionable ENABle Parameter NRf 0 32767 Return parameter NR1 0 32767 Set STATus QUEStionable PTRansition Description Sets or queries the bit sum of the positive tr
54. est is running Condition The Operation Status Condition Register Register indicates the operating status of the power supply If a bit is set in the Condition register it indicates that the event is true Reading the condition register does not change the state of the condition register PTR NTR Filters The PTR NTR Positive Negative transition register determines the type of transition conditions that will set the corresponding bit in the Event Registers Use the Positive transition filter to view events that change from false to positive and use the negative transition filter to view events that change from positive to negative Positive Transition 021 Negative Transition 10 Event Register The PTR NTR Register will dictate the type of transition conditions will set the corresponding bits in the Event Register If the Event Register is read it will be cleared to 0 111 GW INSTEK PSB 1000 Series Programming Manual Enable Register The Enable register determines which registered Events in the Event Register will be used to set the OPER bit in the Status Byte Register 112 GW INSTEK REMOTE CONTROL Standard Event Status Register Group Overview The Standard Event Status Register Group indicates if any errors have occurred The bits of the Event register are set by the error event queue Standard E
55. evice Manager For example in Win7 go to the Control panel Hardware and Sound Device Manager N If you are not familiar with using a terminal Note application to send receive remote commands from via a USB connection please see page 31 for more information Run this query command via the terminal after the instrument has been configured for USB remote control page 28 IDN This should return the manufacturer model number software version and serial number GW INSTEK PSB 1400L TWXXXXXXXXXX X XX XXXXXXXX Manufacturer GWINSTEK Model number PSB 1400L Serial number TWXXXXXXXXXX Software version X XX XXXXXXXX AN For further details please see the programming Note manual available on the GW Instek web site www gwinstek com GW INSTEK REMOTE CONTROL Using Realterm to Establish a Remote Connection Realterm is a terminal program that can be used to Background communicate with a device attached to the serial port of a PC or via an emulated serial port via USB The following instructions apply to version 2 0 0 70 Even though Realterm is used as an example to establish a remote connection any terminal program can be used that has similar functionality N Realterm can be downloaded on Sourceforge net Note free of charge For more information please see http realterm sourceforge net Operation 1 Download Realterm and install according to the instructions on the Re
56. ff Syntax SYSTem CONFigure BEEPer STATe OFF ON 0 1 Query Syntax SYSTem CONFigure BEEPer STATe GW INSTEK REMOTE CONTROL Parameter 0 lt NR1 gt Turns the buzzer off OFF Turns the buzzer off 1 lt NR1 gt Turns the buzzer on ON Turns the buzzer on Return parameter lt Boolean gt Returns the buzzer status Set SYSTem CONFigure BLEeder STATe Description Sets or queries the status of the bleeder resistor Syntax SYSTem CONFigure BLEeder STATe Query Syntax OFF ON AUTO 0 1 2 SYSTem CONFigure BLEeder STATe Parameter 0 lt NR1 gt Turns the bleeder resistor off OFF Turns the bleeder resistor off 1 lt NR1 gt Turns the bleeder resistor on ON Turns the bleeder resistor on 2 lt NR1 gt Turns the AUTO mode on AUTO Turns the AUTO mode on Return parameter lt NR1 gt Returns bleeder resistor status SYSTem CONFigure BTRip I MMediate Set Description Trips the power switch trip circuit breaker to turn the unit off shut down the power Syntax SYSTem CONFigure BTRip IM Mediate Set SYSTem CONFigure BTRip PROTection Description Enables Disables the power switch trip circuit breaker when the OVP or OCP protection settings are tripped This setting only applies after power has been reset Syntax SYSTem CONFigure BTRip PROTection OFF ON 0 1 Query Syntax SYSTem CONFigure BTRip PROTection 91 GW INSTEK PSB 1000 Series Programming Manual Parameter 0 lt NR1 gt
57. g 2 DEF3 User defined setting 3 Example SOUR VOLT LEV IMM AMPL 10 Sets the voltage level to 10 volts Set SOURce VOLTage DEF lt 1 2 3 gt Description Sets or returns the user defined voltage settings Syntax SOURce VOLTage DEF lt 1 2 3 gt lt NRf gt MIN MAX Query Syntax SOURce VOLTage DEF lt 1 2 3 gt MIN MAX Parameter Return 1 DEF1 2 DEF2 3 DEF3 lt NRf gt 0 105 of the rated output voltage in volts MIN Minimum voltage level MAX Maximum voltage level Example SOUR VOLT DEF1 MIN Sets DEF1 to the minimum voltage level Set SOURce VOLTage STEP Description Sets or returns the preset voltage Step amp Step settings Syntax SOURce VOLTage STEP lt rise gt MIN MAX lt fall gt MIN MAX Query Syntax SOURce VOLTage STEP MIN MAX 81 GW INSTEK PSB 1000 Series Programming Manual Parameter Return rise lt NRf gt Step Z 0 105 of the rated voltage output level lt fall gt lt NRf gt Step 0 105 of the rated voltage output level MIN Minimum voltage level MAX Maximum voltage level Example SOUR VOLT STEP MAX MAX Sets the preset Step 7 amp Step settings to the maximum Set SOURce VOLTage STEP RISing Description Sets or returns the preset voltage Step settings Syntax SOURce VOLTage STEP RISing lt NRf gt MIN MAX Query Syntax SOURce VOLTage STEP RISing MIN MAX Parameter Return lt NRf 0 105 of the rate
58. ific errors shall not generate command errors execution errors 123 GW INSTEK PSB 1000 Series Programming Manual or query errors see the other error definitions in this section Error Code Description 310 System error Indicates that some error termed system error by the device has occurred This code is device dependent 320 Storage fault Indicates that the firmware detected a fault when using data storage This error is not an indication of physical damage or failure of any mass storage element Query Errors Overview An lt error event number in the range 499 400 indicates that the output queue control of the instrument has detected a problem with the message exchange protocol described in IEEE 488 2 chapter 6 The occurrence of any error in this class shall cause the query error bit bit 2 in the event status register IEEE 488 2 section 11 5 1 to be set These errors correspond to message exchange protocol errors described in IEEE 488 2 section 6 5 One of the following is true e An attempt is being made to read data from the output queue when no output is either present or pending e Data in the output queue has been lost Events that generate query errors shall not generate command errors execution errors or device specific errors see the other error definitions in this section 124 GW INSTEK REMOTE CONTROL Error Code Description 400 Query error This is
59. l including its main features and front rear panel introduction PSB 1000 Series Overview esee 9 Series lineup see metere aree t t reiten 9 Main Fetar ES erora nee a conie rn mee yes 10 ACCESSO ES iic enc tie tic needed ve peo ELIT REC tess 11 ABDSSFATICE d ecce a Hb e rE DLE Ped ander RNTE RID Ies 13 Front Patel tosta a 13 Rear Panel PSB 1800L M sse 16 Rear Panel PSB 1400L M eee 16 Status Bar Icons Menu Refet nee us a oi eden eni adero deir ete ie eerie 21 GW INSTEK GETTING STARTED PSB 1000 Series Overview Series lineup The PSB 1000 Series consists of 4 models PSB 1400L PSB 1400M PSB 1800L and PSB 1800M Note that throughout the user manual the term PSB 1000 refers to all the models in the PSB 1000 Series lineup unless stated otherwise Model name Output Voltage Output Current Output Power PSB 1400L 40 40 400 PSB 1400M 160 10 400 PSB 1800L 40 80 800 PSB 1800M 160 20 800 GW INSTEK PSB 1000 Series Programming Manual Main Features Performance e Maximum output voltage of 160V e Maximum output current of 80A Features e OVP OCP and OTP protection Low AC input protection e Sequence function e Large 3 5 inch LCD panel e 100V 240V power inlet e Multi range output power e Bleeder circuit ON OFF setting e CV CC priority start function e Internal resistance setting function e Parallel master slave operation
60. lick the Validate button and press Next 43 GW INSTEK PSB 1000 Series Programming Manual Create New VISA TCP IP Resource rem yom itomation INSTRUMENTS En PIP address of your VISA network resource in the orm ococoocecoce he hostname of he device or a compuser some domain dress Vejdae lt Back Ne Finish Cancel a 7 Next configure the Alias name of the PSB 1000 connection In this example the Alias is PSB 8 Click finish Create New VISA TCP IP Resource NATIONAL INSTRUMENTS logics name for jent Use olinses in your coda when opening sessions to devices without specitying their ful VISA resource stings You may assign or change the abas ata later tine trough the alias editor or by clicking on he device to rename it Type in the alias you want Io gasign to this device or leave the a as eld blank to not assign this device Resource Name 172 162325 2268 SOCKET Alios PSB 9 The IP address of the power supply will now appear under Network Devices in the configuration panel Select this icon now 10 Press Open VISA Test Panel GW INSTEK REMOTE CONTROL 9 TCPIPO 172 16 23 25 2268 SOCKET PSB Measugesgent amp Automation Explorer File Edit View Tools Help 4 My System Eh Open VISA Test Panel k Save HY 4 Devices and Interfaces Ws GPIBO SB HS mapu CPIP0 172 16 23 25 2268 80CKET 4 4 Networl ces
61. n DELay TIME 78 SOURce CURRent PROTection S TA Te 79 SOURce CURRencSLEW RISing SOURce CURRencSLEW FALLing ener 79 SOURce RESistance LEVel MMediate PAMPL tte js iniit tnter entree tete es 80 SOURce VOLTage LEVel MMediate AMPLitude 80 SOURce VOLTage DEF lt 1 2 3 gt SOURce VOLTage S TEDP es SOURce VOL Tage STEP RISing eee SOURce VOLTage STEP FALLing eeene 82 SOURce VOLTage LEVel TRIGgered AMPLitude 83 SOURce VOL Tage PRO Tection LEVel 83 SOURce VOLTage PROTection DEF lt 1 2 3 gt 84 SOURce VOL Tage SLEW IRISing eee 84 SOURce VOLTage SLEW FALLing entr 84 Trigger TRIGger TRANSient IMMediate eee Commands TRIGger TRANsientSOURCe TRIGger OUTPut IMMediate TRIGger OUTPutSOURCcCe Trigger Command Examples ttes System SYSTem BEEPer IMMediate eee Commands SYSTem CONFigure BEEPer STATe SYSTem CONFigure BLEeder STATe SYSTem CONFigure BTRip IMMediate SYSTem CONFigure BTRip PROTection SYSTem CONFigure CURRent CONTrol SYSTem CONFigure VOLTage CONTrol SYSTem CON Figure MSLave eene SYSTem CONFigure OUTPut EXTernal MODE 93 SYSTem CONFigure OUTPut PON STAT Ee 94
62. name in string format Query Example SYST COMM LAN HOST P 160054 Returns the host name P 160054 Set SYSTem COMMunicate LAN WEB PACTive Description Sets or queries whether the web password is on or off This setting is applied only after the unit is reset Syntax SYSTem COMMunicate LAN WEB PACTive OFF ON 0 Query Syntax SYSTem COMMunicate LAN WEB PACTive Parameter 0 Web password off OFF Web password off 1 Web password on ON Web password on Return parameter 0 lt boolean gt Web password off 1 lt boolean gt Web password on GW INSTEK REMOTE CONTROL Set SYSTem COM Municate LAN WEB PASSword Description Sets or queries the web password This setting is applied only after the unit is reset Syntax SYSTem COMMunicate LAN WEB PASSword lt NR1 gt Query Syntax SYSTem COMMunicate LAN WEB PASSword Parameter Return NRI 0 9999 SYST COMM LAN WEB PASS 1234 Example Set the web password as 1234 Set SYSTem COMMunicate RLSTate Description Sets or queries the control state of the instrument Note Only applicable for software version 1 60 or above Syntax SYSTem COMMunicate RLSTate LOCal REMote Query Syntax RWLock SYSTem COMMunicate RLSTate Parameter LOCal Sets the instrument to front panel control REMote Sets the instrument to remote interface control RWLock Disables the front panel keys and only allows the instrument to be controlled via the remote
63. ndicates only that an Execution Error as defined in IEEE 488 2 11 5 1 1 5 has occurred 121 GW INSTEK PSB 1000 Series Programming Manual 201 Invalid while Indicates that a command is not executable in local while the device is in local due to a hard local control see IEEE 488 2 5 6 1 5 for example a device with a rotary switch receives a message which would change the switches state but the device is in local so the message can not be executed 203 Command Indicates that a legal password protected protected program command or query could not be executed because the command was disabled 211 Trigger Indicates that a GET TRG or triggering signal ignored was received and recognized by the device but was ignored because of device timing considerations for example the device was not ready to respond Note a DTO device always ignores GET and treats TRG as a Command Error 213 Init ignored Indicates that a request for a measurement initiation was ignored as another measurement was already in progress 220 Parameter Indicates that a program data element related error error occurred This error message should be used when the device cannot detect the more specific errors described for errors 221 through 229 221 Settings Indicates that a legal program data element was conflict parsed but could not be executed due to the current device state see IEEE 488 2 6 4 5 3 and 11 5 1 1 5 122 GW INSTEK REMOT
64. ns important safety instructions that you must follow during operation and storage Read the following before any operation to insure your safety and to keep the instrument in the best possible condition Safety Symbols These safety symbols may appear in this manual or on the instrument A Warning Identifies conditions or practices that WARNING could result in injury or loss of life N Caution Identifies conditions or practices that CAUTION could result in damage to the PSB 1000 or to other properties DANGER High Voltage Attention Refer to the Manual Protective Conductor Terminal Earth ground Terminal BE GW INSTEK SAFETY INSTRUCTIONS Do not dispose electronic equipment as unsorted municipal waste Please use a separate collection facility or contact the supplier from which this instrument was purchased Safety Guidelines General e Do not place any heavy object on the PSB 1000 Guideline e Avoid severe impact or rough handling that N leads to damaging the PSB 1000 CAUTION Do not discharge static electricity to the PSB 1000 e Use only mating connectors not bare wires for the terminals e Do not block the cooling fan opening Do not disassemble the PSB 1000 unless you are qualified Measurement categories EN 61010 1 2010 specifies the measurement categories and their requirements as follows The PSB 1000 doesn t fall under category II III or IV e Measurement catego
65. o pollution or only dry non conductive pollution occurs The pollution has no influence e Pollution degree 2 Normally only non conductive pollution occurs Occasionally however a temporary conductivity caused by condensation must be expected e Pollution degree 3 Conductive pollution occurs or dry non conductive pollution occurs which becomes conductive due to condensation which is expected In such conditions equipment is normally protected against exposure to direct sunlight precipitation and full wind pressure but neither temperature nor humidity is controlled Storage e Location Indoor environment e Temperature 25 C to 70 C e Relative Humidity lt 90 no condensation Disposal Do not dispose this instrument as unsorted municipal waste Please use a separate collection facility or contact the supplier from which this instrument was purchased Please make sure discarded electrical waste is properly recycled to reduce environmental impact GW INSTEK SAFETY INSTRUCTIONS Power cord for the United Kingdom When using the instrument in the United Kingdom make sure the power cord meets the following safety instructions NOTE This lead appliance must only be wired by competent persons WARNING THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in this lead are coloured in accordance with the following code Green Yellow Earth OF Blue Neutral e 6 E Brown Live Phase l
66. onnector USB B VOLT TRIG LAN Fans Line input GPIB Option Rear Panel PSB 1400L M Rear panel terminals J1 Connector USB B VOLT TRIG LAN Fan Line input GPIB Option 16 GW INSTEK GETTING STARTED Line Voltage Input Voltage Input 100 240 VAC Line frequency 47 63Hz 1100VA MAX Rear panel Or i ct Os S U 4 amp The rear panel terminals contain the positive and negative output terminals the voltage sense terminals and the ground terminal ja 1 Connector H lleialtat The J1 Connector is used for external voltage current control or for parallel series control TRIG IN TRIG IN Used to receive a signal from an external device Apply either a negative going or a positive going pulse to the trigger input pin TRIG OUT THIS Pu Used to send a signal to an external device The
67. ote Interface USB PC side Type A host configuration connector PSB 1000 side Rear panel Type B slave connector USB Class CDC communications device class Settings Disable Disables the rear panel USB port Auto Sets the rear panel USB port to auto This will automatically set the port to full or high speed Full Manually sets the port to full speed Steps 1 Connect the Type A Type B USB cable from the PC to the rear panel USB B port 2 Press the Utility key The Utility Utility menu will appear on the display 3 Go to the Interface gt gt gt setting using the scroll wheel and press Enter 4 Use the scroll wheel to go to the Rear USB setting and use the soft keys to set the USB interface Rear USB Disable Auto Full 28 GW INSTEK REMOTE CONTROL 5 When the USB port is connected to the PC the USB icon will appear at the top of the display to show the connection status Connection status ERE Rear USB Rear USB Auto ttin GPIB gt gt gt se g Exit 6 Press Exit F5 to exit from the rear panel USB settings 29 GW INSTEK PSB 1000 Series Programming Manual USB Remote Control Function Check Invoke a terminal application such as Realterm Functionality For USB communication the PSB 1000 emulates a check COM port The UART settings for the USB connection can be seen in the Windows Device Manager To check the COM settings in Windows see the D
68. py the selected file USB to USB Copy to Copy the selected file Mx to memory location M0 9 Save Saves the current settings to the selected memory setting Recall Recalls the selected memory setting View Goes to the View Memory Memory menu Copy to Copies the selected file memory on the USB drive to memory Delete Deletes the selected file on the USB drive Rename Renames the selected file on the USB drive 25 GUIfISTEK PSB 1000 Series Programming Manual Voltage Sets the voltage output settings Current Sets the current output settings OVP Sets the OVP settings OCP Sets the OCP settings 26 GW INSTEK REMOTE CONTROL REMOTE CONTROL This chapter describes basic configuration of TEEE488 2 based remote control For a command list refer to the programming manual downloadable from GW Instek website www gwinstek com N If the instrument is remotely controlled via the Note USB LAN GPIB interface the remote panel lock is automatically enabled Press the Main Local key on the front panel to return to local control Interface Configuration ccs eocesi icut Rep ER XY ORE ED 28 Command Syntax eicere tea rye nda pode eR Soda 2M RENE MERE 48 Command aac cr AR 51 Status Register Overview sssesseeeeesresereerrrerrresereeeeeees 106 Jj di 17 em n S 117 27 GW INSTEK PSB 1000 Series Programming Manual Interface Configuration USB Rem
69. r 109 GW INSTEK PSB 1000 Series Programming Manual Operation Status Register Group Overview The Operation Status Register Group indicates the operating status of the power supply Operation Status Register Condition PTR NTP Event Enable CAI Not Used Not Used Not Used Not Used WTG Not Used Not Used C Not Used CC OND OFD Not Used PR Not Used Ro RO amp amp STATus OPERation CONDition STATus OPERation EVENt STATus OPERation NTRansition lt NRf gt STATus OPERation NTRansition STATus OPERation PTRansition lt NRf gt STATus OPERation PTRansition EE le le au A A a rt SSS SSS nes ta a aa am a a MC 1 STATus OPERation ENABle lt NRf gt STATus OPERation ENABle i ogical O To Status Byte Register Bit Summary Bit Event Bit Weight CAL Calibration mode 0 1 Indicates if the unit is in calibration mode WTG Waiting for trigger 5 32 Indicates if the unit is waiting for a trigger CV Constant voltage mode 8 256 Indicates if the UNIT is in CV mode GW INSTEK REMOTE CONTROL CC Constant current mode 10 1024 Indicates ifthe UNIT is in CC mode OND Output ON Delay 11 2048 Indicates if Output ON delay time is active OFD Output OFF Delay 12 4096 Indicates if Output OFF delay time is active PR Program Running 13 8192 Indicates if a T
70. r Turns the bleeder resistor on or off of auto Average Sets the average level for the smoothing function Low Middle High More 2 of Returns to the 2 previous page GUIfISTEK PSB 1000 Series Programming Manual FUNC View Power On Config Modify CV Control Sets CV control mode CC Control Sets CC control mode PON Run Sets the Power On output settings Turns the output on or executes a sequence at start up Track Sets the tracking mode for multiple units Ext Out Sets the Ext Out line active state Breaker Sets the breaker resistor Sense Sets disables local sense Exit Exits from the View Power On Config settings View Memory MI Shows the M1 settings M2 Shows the M2 settings M3 Shows the M3 settings Exit Exits the View Memory menu Voltage Trigger Vtrig Control Enable Disable voltage trigger control Vt Sets the leading edge Vtrig level Vt2 Sets the trailing edge Vtrig level Polarity Sets the Vtrig polarity as positive or negative 22 GU INSTEK GETTING STARTED FUNC cont TRIGIN POS Positive edge NEG Negative edge Exit Exits from the FUNC menu TRIG OUT POS Positive edge NEG Negative edge Exit Exits from the FUNC menu Sequence Load Loads the selected sequence Exit Exits the sequence menu
71. rameter so receiving SYSTem KLOCk 1 0 is not allowed Fewer parameters were recieved than required for the header for example the KLOCk command requires one parameter so receiving KLOCK is not allowed A character which is not a legal header separator was encountered while parsing the header for example no white space followed the header thus APPL5 1 is an error GUIfISTEK REMOTE CONTROL 112 Program mnemonic too long 113 Undefined header 114 Header suffix out of range 115 Unexpected number of parameters 120 Numeric data error 121 Invalid character in number 128 Numeric data not allowed 131 Invalid suffix The header contains more that twelve characters see IEEE 488 2 7 6 1 4 1 The header is syntactically correct but it is undefined for this specific device for example XYZ is not defined for any device The value of a numeric suffix attached to a program mnemonic see Syntax and Style section 6 2 5 2 makes the header invalid The number of parameters received does not correspond to the number of parameters expected This is typically due an inconsistency with the number of instruments in the selected group This error as well as errors 121 through 129 are generated when parsing a data element which apprears to be numeric including the nondecimal numeric types This particular error message should be used if the device cannot detect a more specific error An inv
72. register determines which Events in the Event Register will be used to set the ESB bit in the Status Byte Register 114 GW INSTEK REMOTE CONTROL Status Byte Register amp Service Request Enable Register Overview The Status Byte register consolidates the status events of all the status registers The Status Byte register can be read with the STB query and can be cleared with the CLS command Output Buffer Error Que Service Status Request Byte Enable F Register Register Tom 0 amp P iis Roget 1 1 ERR 2 L 2 aus 3 H 3 From Standard gt MA 4 i i 1 4 Event Status gt ESH 5 7 i 7 l 5 Register mss 6 t Dd od gd dg 6 OPER 7 1 amp 6 7 From Operation STB SRE NRE Status Register Y Y Y Y tt Y SRE Logical OR Bit Summary Bit Event Bit Weight ERR Error Event Queue 2 4 If data is present in the Error queue the ERR bit will be set QUES Questionable Status 3 8 Register The summary bit for the Questionable Status Register group MAV Message Available This is 4 16 set when there is data in the Output Queue waiting to be read 115 GW INSTEK PSB 1000 Series Programming Manual ESB Event Summary Bit The 5 32 ESB is the summary bit for the Standard Event Status Register group M
73. rigger output VOLT TRIC Syntax OUTPut VTRigger VT lt 1 2 gt lt NRf gt MIN MAX Query Syntax OUTPut VTRigger VT lt 1 2 gt MIN MAX Parameter Return lt NRf gt 0 105 6 of the rated output voltage in volts MIN Minimum voltage level MAX Maximum voltage level 67 GW INSTEK PSB 1000 Series Programming Manual Input Commands INPut TRIGger POLatity eerte ttes 68 Set INPut TRIGger POLarity Description Sets or returns the polarity of the trigger signal input TRIG IN Syntax INPut TRIGger POLarity 0 1 POSitive NEGative Query Syntax INPut TRIGger POLarity Parameter 0 NRI Positive POSitive Positive 1 NR1 Negative NEGative Negative Return parameter lt NR1 gt Returns the polarity of the trigger signal input TRIG IN GW INSTEK REMOTE CONTROL Sense Commands SENSe AVERage COUNL iapun 69 Set SENSe AVERage COUNt Description Determines the level of smoothing for the average setting Syntax SENSe AVERage COUNt lt NR1 gt LOW MIDDIe HIGH Query Syntax SENSe AVERage COUNt Parameter 0 LOW Low level of smoothing 1 MIDDle Middle level of smoothing 2 HIGH High level of smoothing Return parameter lt NR1 gt Returns the level of smoothing 0 Low level of smoothing 1 Middle level of smoothing 2 High level of smoothing Example SENSe AVERage COUNt 1 Sets the level of smoothing to middle 69 GW INSTEK PSB 1000 Series
74. ring The string is returned as string Example SYSTem ERRor 100 Command error 100 GW INSTEK REMOTE CONTROL Set SYSTem KEYLock MODE Description Sets or queries the key lock mode Syntax SYSTem KEYLock MODE 0 1 Query Syntax SYSTem KEY Lock MODE Parameter 0 Panel lock allow output off Return parameter 1 Panel lock allow output on off Set SYSTem KLOCk Description Enables or disables the front panel key lock Syntax SYSTem KLOCk OFF ON 0 1 Query Syntax SYSTem KLOCk Parameter 0 Panel keys unlocked OFF Panel keys unlocked 1 Panel keys locked ON Panel keys locked Return parameter 0 lt boolean gt Panel keys unlocked 1 lt Boolean gt Panel keys locked SYSTem PRESet Set Description Resets all the settings to the factory default settings See page 126 for details Syntax SYSTem PRESet SYSTem VERSion Description Returns the version of the SCPI specifications that the unit complies with Query Syntax SYSTem VERSion Return lt 1999 0 gt Always returns the SCPI version 1999 0 101 GW INSTEK PSB 1000 Series Programming Manual IEEE 488 2 Common Commands CLS Set Description The CLS command clears the Standard Event Status Operation Status and Questionable Status registers The corresponding Enable registers in each of the above registers are not cleared If a lt NL gt newline code immediately precedes a CLS command the Error Que and th
75. ry IV is for measurement performed at the source of low voltage installation e Measurement category III is for measurement performed in the building installation e Measurement category Il is for measurement performed on the circuits directly connected to the low voltage installation e Ois for measurements performed on circuits not directly connected to Mains Power Supply AC Input voltage range 100Vac to 240Vac N e Frequency 47Hz 63Hz WARNING e To avoid electrical shock connect the protective grounding conductor of the AC power cord to an earth ground GW INSTEK PSB 1000 Series Programming Manual Cleaning the PSB e Disconnect the power cord before cleaning 1000 e Usea soft cloth dampened in a solution of mild detergent and water Do not spray any liquid Do not use chemicals containing harsh material such as benzene toluene xylene and acetone Operation e Location Indoor no direct sunlight dust free Environment almost non conductive pollution Note below e Relative Humidity 20 85 no condensation e Altitude Maximum 2000m e Temperature 0 C to 40 C Pollution Degree EN 61010 1 2010 specifies the pollution degrees and their requirements as follows The PSB 1000 falls under degree 2 Pollution refers to addition of foreign matter solid liquid or gaseous ionized gases that may produce a reduction of dielectric strength or surface resistivity Pollution degree 1 N
76. s MEASure SCALar CURRent DC eene 62 MEASute SCALar VOLTage DC e 62 MEASutre SCALar POWer DC eere 62 MEASure SCALar CURRent DC Query Description Takes a measurement and returns the average output current Syntax MEASure SCALar CURRent DC Return parameter lt NRf gt X Returns the current in amps MEASure SCALar VOLTage DC Query Description Takes a measurement and returns the average output voltage Syntax MEASure SCALar VOLTage DC Return lt NRf gt Returns the voltage in volts MEASure SCALar POWer DC Query Description Takes a measurement and returns the average output power Syntax MEASure SCALar POWer DC Return lt NRf gt Returns the power measured in watts 62 GW INSTEK REMOTE CONTROL Output Commands OUTPutDBLEay ON 5 nette tb reed cedar 63 QUT Put DE Lay OFF wisest eet eesseeseeteeseeteexp casessessucevaasersessee 63 OUTPut MODE OUTPut STATe IMMediate e 64 OUTPut S TATe TRIGgeted ee 64 OUTPut PROTection CLEar OUTPut PROTection TRIPped eee 65 OUT Put TRlIGger PO Latity tiurtttt tta OUTPut VTRigger CONTrol OUTPutVTRigget POLatity enean tnnt OUT Put VI Rigget S TATe eicere 66 OUTPutVIRigget VI 12 teorie nn 67 Set OUTPut DELay ON Description Sets the Delay
77. scription USB driver GW INSTEK GETTING STARTED Appearance Front Panel Voltage Current OVP Menu keys Main Local CLR PROT OCP keys FUNC Utility File Number pad Scroll wheel GMIMSTEK PsE 4onw 9 Range Oc A E See LCD Display Arrow keys F1 F5 soft keys Loek unloek 3 Enter key Output lt S S ES Ww Sense USB A port Terminal Power switch Sense Ground terminal Terminal Item Description Power Switch Turns on the mains power Front Panel Output Terminals AN 160V 10A Positive sense terminal Positive terminal 13 GW INSTEK PSB 1000 Series Programming Manual Ground terminal Negative terminal Negative sense terminal USB A Port The USB port is used for data e SS transfer loading test scripts etc LCD Screen Displays the voltage current settings measurement readings and menu systems Function Keys Cr Cre C C Assigned to the soft keys displayed on the bottom of the screen Main Key Local Returns operation to the main qc operation screen Local Key Pressing the Main Local key will also return the unit to local mode from remote control mode
78. sple Capture Pins Send Echo Por 2c i2c 2 12CMisc Misc nj CI Baud 600 x eon fi x Spy V Change M affare Flow Control Parity Data Bits Stop Bits w 7 None 8bits 1bit C 2bits Bis n mes 2 ea 7 bits Hardware Flaw Control Transmit Xoff Char 19 C Mak C Sbits None C RTS CTS Wu C Space C Shits C DTR DSR C RS485 tts C Inet 6 Click on the Send tab In the EOL configuration check on the LF check boxes Enter the query idn Click on Send ASCII By RealTerm Serial Capture Program 2 0 0 70 Display Por Capture Pins EchoPort 2c 1202 in n Z Send Number Bet J Z Send Numbers ed fite el 8 c tr Repeats tS Literal Strip Spaces crc SMBUS Dump File to Port 4 ciemp capture tt E SendFile X Stop Delays 0 ED r FI Bepeats 1 2 f 7 The terminal display will return the following GW_INSTEK PSB 1400L TWXXXXXXXXXX X XX XXXXXXXX 33 GW INSTEK PSB 1000 Series Programming Manual manufacturer model serial number software version 8 If Realterm fails to connect to the PSB 1000 please check all the cables and settings and try again Configure GPIB Interface Optional To use GPIB the optional PSB 105 GPIB interface card must first be installed N The GPIB interface card PSB 105 must first be Note installed before the GPIB interface can b
79. tatus Register Overview To program the PSB 1000 power supply effectively the Status registers need to be understood This chapter explains in detail how the Status registers are used and how to configure them Introduction to the Status Registers sss The Status Registers sss Questionable Status Register Group Operation Status Register Group Standard Event Status Register Group Status Byte Register amp Service Request Enable Register115 Introduction to the Status Registers Overview The status registers are used to determine the status of the power supply The status registers maintain the status of the protection conditions operation conditions and instrument errors The PSB 1000 Series have a number of register groups e Questionable Status Register Group e Standard Event Status Register Group Operation Status Register Group e Status Byte Register e Service Request Enable Register e Service Request Generation e Error Queue e Output Buffer The next page shows the structure of the Status registers 106 GW INSTEK REMOTE CONTROL The Status Registers Questionable Status Register Condition PTR NTP Event Enable OV OverVollage 0 0
80. tax SOURce CURRent PROTection DELay TIME lt NRf MIN MAX DEF Query Syntax SOURce CURRent PROTection DELay TIME MIN MAX 78 GW INSTEK REMOTE CONTROL Parameter Return lt NRf gt 0 1 2 0 sec MIN 0 1 sec MAX 2 0 sec DEF System defined setting Set SOURce CURRent PROTection STATe Description Turns OCP over current protection on or off Syntax SOURce CURRent PROTection STATe 0 1 OFFJON Query Syntax SOURce CURRent PROTection STATe Parameter Return 0 lt NR1 gt Turns the buzzer off OFF Turns the OCP off 1 lt NR1 gt Turns the OCP on ON Turns the OCP on Return parameter lt Bool gt Returns the protection status 0 or 1 Example SOUR CURR PROT STAT OFF Turns OCP off Set SOURce CURRent SLEW RISing Description Sets or queries the rising current slew rate This is only applicable for CC slew rate priority mode Syntax SOURce CURRent SLEW RISing lt NRf gt MIN MAX Query Syntax SOURce CURRent SLEW RISing MIN MAX Parameter Return lt NRf gt 0 01 rating current x 2 MIN Minimum rising current slew rate MAX Maximum rising current slew rate Example SOUR CURR SLEW RIS 72 Sets the rising current slew rate to 72A s Set SOURce CURRent SLEW FALLing Description Sets or queries the falling current slew rate This is only applicable for CC slew rate priority mode 79 GW INSTEK PSB 1000 Series Programming Manual
81. the TRG or IEEE 488 1 get group execute trigger command to start the trigger IMMediate Starts the trigger immediately default Example TRIG TRAN SOUR BUS Sets the trigger source as BUS 86 GW INSTEK REMOTE CONTROL TRIGger OUTPut IM Mediate Set Description Generates a software trigger for the output trigger system On a trigger sets the output state Refer to the OUTP TRIG command on page 64 Syntax TRIGger OUTPut IMMediate Related OUTPut STATe TRIGgered commands Set TRIGger OUTPut SOURce Description Sets or queries the trigger source for the output system Syntax TRIGger OUTPut SOURce BUS IMMediate Query Syntax TRIGger OUTPut SOURce Parameter Return BUS Internal software trigger Waits for the TRG or IEEE 488 1 get group execute trigger command to start the trigger IMMediate Starts the trigger immediately default Example TRIG OUTP SOUR BUS Sets the trigger source of the output system as BUS Trigger Command Examples 1 The transient system for the trigger in immediate mode Example 1 TRIG TRAN SOUR IMM CURR TRIG MAX VOLT TRIG 5 INIT NAME TRAN lt The current changes to the maximum and the voltage changes to 5V GW INSTEK PSB 1000 Series Programming Manual 2 The transient system for the trigger in BUS mode Example 2 TRIG TRAN SOUR BUS CURR TRIG MAX VOLT TRIG 5 INITNAME TRAN TRIG TRAN or TRG lt The current changes to the maxim
82. turn lt NRf 4 44V 1400L 5 176V 1400M 4 44V 1800L 5 176V 1800M MIN Minimum OVP level MAX Maximum OVP level DEFI User defined setting 1 DEF2 User defined setting 2 DEF3 User defined setting 2 Example SOUR VOLT PROT LEV MAX Sets the OVP level to its maximum GW INSTEK PSB 1000 Series Programming Manual SOURce VOLTage PROTection Set DEF lt 1 2 3 gt Description Sets or returns the user defined OVP settings Syntax SOURce VOLTage PROTection DEF lt 1 2 3 gt lt NRf amp MIN MAX Query Syntax SOURce VOLTage PROTection DEF lt 1 2 3 gt MIN MAX Parameter Return lt NRf gt 4 44y 1400L 5 176V 1400M 4 44V 1800L 5 176V 1800M MIN Minimum OVP level MAX Maximum OVP level Example SOUR VOLT PROT DEF1 MIN Sets DEF1 to the minimum OVP level Set SOURce VOLTage SLEW RISing Description Sets or queries the rising voltage slew rate This is only applicable for CV slew rate priority mode Syntax SOURce VOLTage SLEW RISing lt NRf gt MIN MAX Query Syntax SOURce VOLTage SLEW RISing MIN MAX Parameter Return lt NRf gt 0 01 rating voltage x 2 MIN Minimum rising voltage slew rate MAX Maximum rising voltage slew rate Example SOUR VOLT SLEW RIS MAX Sets the rising voltage slew rate to its maximum Set SOURce VOLTage SLEW FALLing Description Sets or queries the falling voltage slew rate This is only applicable for CV slew rate priority mo
83. tus registers Syntax STATus PRESet 73 GW INSTEK PSB 1000 Series Programming Manual Source Commands SOURce CURRent LEVel IMMediate AMPLitude 74 SOURce CURRent DEF lt 1 232 sse SOURce CURRent STEP SOURce CURRent STEP RISINg eee SOURce CURRent STEP FALLing SOURce CURRent LEVel TRIGgered AMPLitude 77 SOURce CURRent PROTection LEVel 77 SOURce CURRent PROTection DEF lt 1 2 32 78 SOURce CURRent PROTection DELay TIME 78 SOURce CURRent PROTection STATe 79 SOURce CURRent SLEW RISing eee 79 SOURce CURRent SLEW FALLing eene 79 SOURce RESistance LE Vel MMediate SA MP bir M 80 SOURce VOLTage LEVel IMMediate AMPLitude 80 SOURce VOLTage DEF lt 1 2 3 gt see SOURce VOL Tage S TEDP reete tentes SOURce VOLTage STEP RISing SOURce VOLTage STEP FALLing SOURce VOLTage LEVel TRIGgered AMPLitude 83 SOURce VOLTage PROTection LEVel 83 SOURce VOLTage PROTection DEF lt 1 2 32 84 SOURce VOLTage SLEW RISing eee 84 SOURce VOLTage SLEW FALLING eeeennn 84 SOURce CURRent LEVel IM Mediate Set AMPLitude Description Sets or queries the current level in amps For externally set current levels from the analog control conne
84. um and the voltage changes to 5V 3 The output system for the trigger in immediate mode Example 3 TRIG OUTP SOUR IMM OUTP TRIG 1 INIT NAME OUTP lt The output changes to ON 4 The output system for the trigger in BUS mode Example 4 TRIG OUTP SOUR BUS OUTP TRIG 1 INITNAME OUTP TRIG OUTP or TRG lt The output changes to ON 88 GW INSTEK REMOTE CONTROL System Function Command SYSTem BEEPer IMMediate ee SYSTem CONFigure BEEPer STATe SYSTem CONFigure BLEeder STATe SYSTem CONFigure BTRip IMMediate SYSTem CONFigure BTRip PROTection SYSTem CONFigure CURRent CONTrol SYSTem CONFigure VOLTage CONT tl 92 SYSTem CONFigure MSLave eene 93 SYSTem CONFigure OUTPut EXTernal MODE 93 SYSTem CONFigure OUTPut PON STATe 94 SYSTem CONFigure SENSe STATe 94 SYSTem COMMunicate ENABle esee 95 SYSTem COMMunicate GPIB SELF ADDhRess 95 SYSTem COMMunicate LAN IPADdtess 96 SYSTem COMMunicate LAN GATTEway SYSTem COMMunicate LAN SMASK ess SYSTem COMMunicate LAN MAC eene SYSTem COMMunicate LAN DHCP SYSTem COMMunicate LAN DNS SYSTem COMMunicate LAN HOS Tname sss SYSTem COMMunicate LAN WEB PACTive SYSTem COMMunicate LAN WEB PAS
85. vent Status Register Event Enable opo 0 0 rac 1 1 QU 2 2 DDE 3 3 ede pt ovp S EUST gt URd 6 6 rot 7 ESR EO PP PP ESE NR tt Pp T ESE vYvYvvvY Logical OR To Status Byte Register Bit Summary Bit Event Bit Weight OPC Operation complete 0 The OCP bit is set when all selected pending operations are complete This bit is set in response to the OPC command RQC Request control 1 2 QUE Query Error 2 4 The Query Error bit is set in response to an error reading the Output Queue This can be caused by trying to read the Output Queue when there is no data present DDE Device Dependent Error 3 8 Device specific error 113 GW INSTEK PSB 1000 Series Programming Manual EXE Execution Error 4 16 The EXE bit indicates an execution error due to one of the following illegal command parameter parameter out of range invalid parameter the command didn t execute due to an overriding operation condition CME Command Error 5 32 The CME bit is set when a syntax error has occurred The CME bit can also be set when a lt GET gt command is received within a program message URQ User Request 6 64 PON Power On 7 128 Indicates the power is turned on Event Register Any bits set in the event register indicate that an error has occurred Reading the Event register will reset the register to 0 Enable Register The Enable
86. with active current sharing e Remote sensing to compensate for voltage drop in load leads e Analog output programming and monitoring Interface e Ethernet port e USB host e USB CDC e GPIB optional e External Control I O GUIfISTEK GETTING STARTED Accessories Standard Part number Accessories CD ROM PSW 009 GTL 240 PSB 106 Optional Part number Accessories PSW 001 PSW 002 PSW 003 Description User manual programming manual Power cord Output terminal cover Type A B USB Cable Basic Accessory Kit M4 terminal screws and washers x2 M8 terminal bolts nuts and washers x2 Analog control protection dummy x1 analog control lock level x2 short bar x1 Description Analog remote control connector kit Socket x 1pc Pins x 10pcs Protection cover x set Chassis connection wire x Simple IDC tool Contact removal tool 11 GUIfISTEK Download 12 PSB 101 PSB 102 PSB 103 PSB 104 PSB 105 GRA 418 GRA 418 E GTL 123 Name gw psblk inf PSB 1000 Series Programming Manual Cable for 2 units of PSB 1000 units in parallel mode connection Cable for 3 units of PSB 1000 units in parallel mode connection Cable for 4 units of PSB 1000 units in parallel mode connection Cable for 2 units of PSB 1000 units in series mode connection GPIB card Rack mount adapter JIS Rack mount adapter EIA Test leads 1x red 1x black De

PSB-1000 series Programming manual

Contents

Download Pdf Manuals

Related Search

Related Contents