Technical Manual Of Intel Bay Trail Series CPU
Contents
1. 3 6 3 7 ADVANCED MENU 3 8 CHIPSET rrr erret Inr a 3 9 SECURITY 3 11 SAVE amp EXIT MENU iii 16 16 20 26 27 27 28 28 29 30 41 44 45 Environmental Safety Instruction Avoid the dusty humidity and temperature extremes Do not place the product in any area where it may become wet 0 to 60 centigrade is the suitable temperature The figure comes from the request of the main chipset Generally speaking dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components Suggest starting the computer until the temperature goes up The increasing temperature of the capacitor may decrease the life of computer Using the close case may decrease the life of other device because the higher temperature in the inner of the case Attention to the heat sink when you over clocking The higher temperature2. Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed The optional settings are Suspend Disabled 53 Suspend to RAM Wakeup Function Settings Press Enter to make settings for the following sub items Wake up System with Fixed Time Use this item to enable or disable system wake up on alarm event The optional settings Disabled Enabled When set as Enabled system will wake on the hour min sec specified Wake up System with Dynamic Time Use this item to enable or disable system wake up by RTC alarm The optional settings Disabled Enabled When set as Enabled system will wake on the current time increased minute s PS2 KB MS Wakeup Use this item to enable or disable PS2 KB MS wakeup from 53 54 55 state This function is only supported when ERP function is disabled This item is only supported when ERP Support is set as Disabled USB 53 54 Wakeup Use this item to enable or disable USB S3 S4 wakeup This function is only supported when ERP function is disabled This item is only supported when ERP Support is set as Disabled Super I O Configuration Press Enter to make settings for the following sub items Super IO Configuration ERP Function The optional settings Disabled Auto This item should be set as Disabled if you wish to have all active wake up functions Serial Port 1 Configuration Press Enter to
3. IN GND 5 SATAPWA 4 pin SATA Power Connector Hi ceo ECS 6 CPUFAN SYSFAN1 SYSFAN2 4 pin Fan Connectors No Definition GND 12V Fan Power Fan Speed WIN Control 2 2 2 Headers 1 FP_AUDIO1 9 pin Line Out MIC In Header This header connects to Front Panel Line out MIC In connector with cable ar 1no ann 103130 ar oi N Pin 1 W 29IIN 1N0 3NI 1 3SN3S TZOIW TLNO INI Line Out MIC Header a Pin No Definition N gt A 3 LAN1_LED1 LAN2_LED1 2 pin LAN Activity LED Header LED Pin1 LED LAN2_LED1 LAN1 LEDI 031 Ysa Sly 519 l 6 Pinl NIS Inos QN9 38 Fea 5 F USB1 F USB2 9 pin USB 2 0 Port Headers 8800 ED 33 viva Vivd DIA N Pin 1 gt SDA viva Vivd a31 Pin 1 N 5154 SDA LISIU 7 SPK LED pin Speaker Header amp PW
4. 2 Pin 1 2 4 Close SYSFAN1 R P M Selected 1 H fai 619 5 Ja 8380 E 5 4 6 Close SYSFAN2 R P M Selected Eg 2 2 Connectors and Headers 2 2 1 Connectors 1 Rear Connectors VGA Port RJ 45 LAN Ports Parallel Port USB 2 0 Port TO NrLine Out Port 9 24V j DC Power in o _ MIC Port Connector USB 3 0 Port USB 2 0 Ports HDMI Port COMI Port PS 2 KB amp MS Port 2 9 pin Block RS232 422 485 Port COM port can function as RS232 422 485 port In normal settings COM1 functions as RS232 port With compatible COM cable COM1 can function as RS422 or RS 485 port User also needs to go to BIOS to set Transmission Mode Select for COM1 refer to Page 32 at first before using specialized cable to connect different pins of this port RS422 RX B RS422 RX A RS422 TX A RS485 D A RS422 TX B RS485 D B For RS422 Mode For RS485 Mode pra 2 Block DC9V 24V Internal Connector L Pin No Definition 1 GND 2 9V 24V DC_IN 4 SATA1 SATA2 7 pin Block SATAII Port connector These are high speed SATAII ports that support 3GB s transfer rate Pin No Definition GND TXP TXN GND RXN RXP Note SA TA2 shares with MSATA1 i SATA slot
5. 1 N 1 2 Open ATX Mode Selected 41003 2 Pin 1 1 2 Close AT Mode Selected ATX Mode Selected Press power button to power on after power input ready AT Mode Selected Directly power on as power input ready Pin 3 amp 4 of JP14 Message Display Function Select Pin 3 amp 4 of JP14 Case Open Function Select 4003 2 Pin1 3 4 Open Normal 4 2 OPin1 3 4 Close Case Open Function Selected One Touch Pin 3 4 Close When Case open function pin short to GND the Case open function was detected When Used needs to enter BIOS and enable Case Open Detect function In this case if your case is removed next time when you restart your computer a message will be displayed on screen to inform you of this JME1 3 pin Clear ME Function Setting JME1 Clear ME RTC ee 1 3 1 2 Close Normal meo 3 2 3 Close Clear ME_RTC Pin 1 amp 3 amp 5 of JP15 RJ 11 Port 6 5 4 3 2 lt Pin 1 1 3 Close RJ 11 VCC 12V I 419 2 0 Pin 1 3 5 Close RJ 11 VCC 24V 13 Pin 2 amp 4 amp 6 of JP15 6 pin SYSFAN1 SYSFAN2 R P M Select Pin 2 amp 4 amp 6 of JP15 SYSFAN1 2 R P M SELON 6 5 2 2 4 3
6. The optional settings are Disabled Enabled Disable VBIOS disable LVDS Enable VBIOS enable LVDS Note When set as Enabled user can make further settings in LVDS Panel Type LVDS Panel Type Use this item to manually select LVDS panel type The optional setting 800 600 18bit Single 800 600 24bit Single 1024 x 600 18bit Single 800x 480 18bit Single 1024 x 768 18bit Single 1024 x 768 24bit Single 1280 x 768 24bit Single 1280 x 1024 24bit Dual 1366 x 768 18bit 42 Single 1366 x 768 24bit Single 1440 x 900 18bit Dual 1440 x 900 24bit Dual 1280 x 800 18bit Single 1280 x 800 24bit Single 1680 x 1050 24bit Dual 1920 x 1080 24bit Dual South Bridge Press Enter to set south bridge parameters USB Configuration Press Enter to make settings for the following sub items USB Configuration USB 3 0 Support The optional settings are Enabled Disabled Auto Smart Auto Note When set as Disable USB 2 0 Support is applicable for user to make further settings USB 3 0 Link Power Management The optional settings are Enabled Disabled Note This item only show up when USB 3 0 Support set as Enabled Auto or Smart Auto USB 2 0 Support The optional settings are Auto Disabled Audio Controller The optional settings are Disabled Enabled Azalia HDMI Codec Use this item to enable or disable internal HDMI
7. codec for Azalia The optional settings are Disabled Enabled PCI E Slot Speed The optional settings are Auto Gen2 Gen1 MPE Controller The optional settings are Enabled Disabled Speed The optional settings are Auto Gen2 Gen1 43 Onboard Lan1 Controller Onboard Lan2 Controller The optional settings are Enabled Disabled System State after Power Failure Use this item to select AC power state when power is re applied after a power failure The optional settings are Always Off Always On Former State 3 9 Security Menu Aptio Setup Utility Security W Password Description Set Administrator Password If ONLY the Administrator s password is set then this only limits access to Setup and 15 only asked for when entering Setup If ONLY the User s password is set then this a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password length must be in the following range Minimum length Maximum length Select Screen th Select Item Enter Select User Password k Change i General Help 2 Previous Values t Optimized Defaults Save 8 Exit ESC Exit Security menu allow users to change administrator password and user password settings 3 10 Boot Menu Setup Utility Boot Configuration Number of seconds to walt for setup activation key Bootup NumLock S
8. may decrease the life of the device and burned the capacitor iv USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER NO PART OF THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE CORRECT ANY TIME WITHOUT NOTICE MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND AND WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTIAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMANGES FOR LOSS OF PROFIT LOSS OF BUSINESS LOSS OF USE OF DATA INTERRUPTION OF BUSINESS AND THE LIKE PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT WITHOUT INTENT TO INFRINGE Manual Revision Information Reversion Revision History Date 1 0 First Edition September 25 2014 Item Checklist Motherboard User s Manual CD for motherboard utilities Cable s NONO 1 1 Chapter 1 Introduction of the Motherboard Feature of Motherboard Onboard Intel Bay Trail series processor with low power consumption never denies high performance Support DDR3L
9. model supported otherwise the board will not start 3 MSATA slot shares function with SATA2 port i e only one can function at a time Front Panel Audio Header si Jumper Position n UU JP15 Brio DUI JP14 Ceno diss JP8 PEB ED A Jumper Jumper Description INVERTER1 VCC 5V 12V Select 3 Pin Block LVDS1 PVCC 3 3V 5V 12V Select 4 Pin Block LCD Back Light PWM DC Mode Select 3 Pin Block P5 i Mini PCI E Slot MPE1 3 3V 3 Pin Block 3VSB Select COM1 Port Pin9 Function Select COM2 Header Pin9 Function Select 4 Pin Block Connectors DCIN1 DC 9V 24V Power in Connector VGA1 VGA Port Connector LPT1 Parallel Port Connector UL1 Top RJ 45 LAN Port Connector Middle USB 2 0 Port Connector Bottom USB 3 0 Port Connector UL2 Top RJ 45 LAN Port Connector Middle amp Bottom USB 2 0 Port Connector X 2 Bottom Audio MIC In Connector Headers Header Name Description FP AUDIO1 Front Panel Audio Header 9 pin Block FP1 Front Panel Header PWR LED 9 pin Block HDD LED Power Button Reset SPK LED1 Power LED amp Speaker Header 7 pin Block Chapter 2 Hardware Installation 2 1 Jumper Setting JP1 3 pin INVERTER1 VCC 5V 12V Select n yp1 INVERTER1 VCC ma F e 3 SID 6 SA Mii 9 H E i 1 2 Clos
10. off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should be claimed by EHCI driver The optional settings are Disabled Enabled USB Mass Storage Driver Support The optional settings are Disabled Enabled USB hardware delay and time outs USB Transfer time out Use this item to set the time out value for control bulk and interrupt transfers The optional settings are 1 sec 5 sec 10 sec 20 sec Device reset time out Use this item to set USB mass storage device start unit command time out The optional settings are 10 sec 20 sec 30 sec 40 sec Device power up delay Use this item to set maximum time the device will take before it properly reports itself to the host controller Auto uses default value for a root port it is 100 ms for a hub port the delay is taken from hub descriptor The optional settings Auto Manual Select Manual you can set value for the following sub item Device Power up delay in seconds Device Power up delay in seconds The delay range is from 1 to 40 seconds in one second increments Realtek PCle GBE Family Controller MAC XX XX XX XX Realtek PCle GBE Family Controller Use this item to get driver information and configure gigabit ethernet device parameter 3 8 Chipset Menu Chipset b South Bridge North Bridge Aptio Setup Utility t North Bridg
11. power connector 1 SATA Power connector 1 CPU FAN connector 2 SYSFAN connector 1 Front panel audio header 1 SPEAK_CON header 2 LAN LED activity header Internal I O 5 Serial port header 2 9 pin USB 2 0 header Expansible to 4 USB 2 0 ports 1 Front panel header 1 Power LED amp speaker header 1 GPIO_CON header 1 SMBUS header 1 LVDS inverter 1 LVDS header 1 3 Layout Diagram Rear IO Panel Diagram RJ 45 LAN Ports VGA Port Parallel Port USB 2 0 Port Uyine Out Port MIC Port 9V 24V DC Connector USB 2 0 Ports USB 3 0 Port HDMI Port COMI Port PS 2 KB amp MS Port Motherboard Internal Diagram 9V 24V Internal Power Connector LVDS Inverter SYSFANI Header Ez an Em T VL tutte TET DDR3L SODIMM Slot E SODIMMI Rear IO a E Please cf SMBUS Header Hi E refer to LEI Half size Mini PCIE P _ Slot MPEI PE CPUFAN Header age3 H SATA Hard Disk sie Power Out Connector Full size M SATA s i Slot MSATA1 Speaker Connector 1E I SATAII Ports GPIO Header Power LED Header amp Speaker Header SE mmis Es Gao PCI Express x1 Slot Serial Port Bode panel 2 COM2 3 4 5 6 USB 2 0 Headers Note 1 The module for SODIMM1 should be DDR3L 1 35V SODIMM and not exceeding 8GB total capacity 2 The SODIMM installed should be of or above the memory clock the
12. Information TXE FH Vers lon 01 01 00 1009 Select Screen thi Select Item Enter Select 1 Change Opt Fl General Help F2 Previous Values Optimized Defaults F4 Save A Exit ESC Exit System Date Set the date Please use Tab to switch between data elements System Time Set the time Please use Tab to switch between time elements 29 3 7 Advanced Menu Aptio Setup Utility Advanced t 05 Selection ACPI Settings Wake up Funct lon Settings Super 10 Configuration PG Health Status Shutdoun Temperature Configuration Serial Port Console Redirection CPU Configuration SATA Configuration Network Stack Configuration CSH Configuration USB Configuration 2 2 w Realtek PCIe OBE Family Controller MAC 00 30 18 00 00 24 A Select Screen Realtek PCIe GGE Family Controller HAC 00 30 10 00 00 25 th Select Item Enter Select Change Opt 1 General Help Previous Values Optimized Defaults Save 8 Exit ESC Exit OS Selection The optional settings Android Windows 8 X Windows 7 Note User needs to go to this item to select OS before installing OS If Windows Embedded standard 8 Please select Windows 8x and set USB 3 0 Support as Disabled USB 2 0 Support as Enabled refer to Page 43 ACPI Settings Press Enter to make settings for the following sub item ACPI Settings ACPI Sleep State
13. R LED Header m n a x ily J Z ilL a i gil y i 1 ia B HER Um SED Em SPK PWRLED NC PWRLED NC PWRLED SPK 2 Pin 1 VCC3 GND GPIO 20 GPIO 17 GPIO 16 GPIO 13 GPIO 12 GPIO 11 GPIO 04 GPIO 02 2 Pin 1 9 SMBUS1 4 Pin SM BUS Header SMBUS_DATA GND SMBUS_CLK NC Pin 1 Pin No Definition Backlight Enable Backlight PWM Backlight VCC Backlight VCC GND GND Backlight Up SW Backlight Down SW COIN 9 N 11 LVDS 30 pin 24 bit Dual Cha pez Sm fi H d gt LU e nnel LVDS Header LVDS Header Pin NO Pin Define Pin NO Pin Define Pin 1 LVDSB DATAN3 Pin 2 LVDSB DATAP3 Pin 3 LVDS CLKBN Pin 4 LVDS CLKBP Pin 5 LVDSB DATAN2 Pin 6 LVDSB DATAP2 Pin 7 LVDSB DATAN1 Pin 8 LVDSB DATAP1 Pin 9 LVDSB DATANO Pin 10 LVDSB DATAPO Pin 11 NC Pin 12 NC Pin 13 N A Pin 14 GND Pin 15 GND Pin 16 GND Pin 17 LVDSA DATAP3 Pin 18 LVDSA DATAN3 Pin 19 LVDS CLKAP Pin 20 LVDS CLKAN Pin 21 LVDSA DATAP2 Pin 22 LVDSA DATAN2 Pin 23 LVDSA DATAP1 Pin 24 LVDSA DATAN1 Pin 25 LVDSA DATAPO Pin 26 LVDSA DATANO Pin 27 PVDD Pin 28 N A Pin 29 PVDD Pin 30 P
14. SO DIMM 1066 1333 MHz up to 8GB Support Mini PCIE connector Support m SATA connector Support 2 SATAII device Integrated with 1 24 bit dual channel LVDS header Support HDMI display output Support USB 3 0 data transport demand Support CPU Smart FAN Compliance with ErP standard Support Watchdog function 1 2 Specification Spee Description Design 9 6 layers Mini ITX PCB size 17x 17 cm Embedded CPU Integrated with Intel Bay Trail D M I series CPU e 1 DDR3L SODIMM Slot for un buffered DDR3L 1066 Mhz or 1333 Mhz SDRAM expandable to 8GB Memory Slot Memory clock supporting range is decided by specific CPU of the model For more memory compatibility information please consults your local dealer e 1 Half size Mini PCIE slot Expansion Slot 1 PCIE x1 slot Integrated with dual Realtek 81116 PCI E Gigabit LAN chips LAN Chip Support Fast Ethernet LAN function of providing 10 100 1000Mbps Ethernet data transfer rate Audio Chi Realtek ALC662 2 CH HD Audio Codec integrated CE Audio driver and utility included st 2 SATAII 3Gb s port erage 1 mSATA slot shared with SATA2 port BIOS AMI 64MB Flash ROM 1 DC 9V 24V power in connector 1 VGA port 1 Parallel port 1 RJ 11 port 1 PS 2 keyboard amp mouse combo port 1 HDMI port 1 COM port 2 RJ 45 LAN port 3 USB 2 0 port 1 USB 3 0 port 1 Line out port Rear I O pO MIC port 1 DC 9V 24V internal
15. Technical Manual Of Intel Bay Trail Series CPU Based Mini ITX M B NO G03 NF9U F Revision 1 0 Release date September 25 2014 Trademark Specifications and Information contained in this documentation are furnished for information use only and are subject to change at any time without notice and should not be construed as a commitment by manufacturer Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding To minimize pollution and ensure environment protection of mother earth please recycle ii TABLE OF CONTENT ENVIRONMENTAL SAFETY INSTRUCTION rr USER S NOTICE MANUAL REVISION INFORMATION erre uedde Hr nuan alare CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD 1 1 FEATURE OF MOTHERBOARD eene nnne nennen nnn nennen irren 1 2 SPECIFICATION iii 1 3 LAYOUT DIAGRAM CHAPTER 2 HARDWARE INSTALLATION 2 1 JUMPER SETTING eese nnne nennen nennen nnns 2 2 CONNECTORS AND HEADERS eene nnns 2 2 1 CONNECTORS nonien ii 2 222 HEADERS CHAPTER 3 INTRODUCING BIOS 3 1 ENTERING SETUP nennen uu DR 3 2 BIOS MENU SCREEN
16. VDD Pin 31 GND Pin 32 GND Chapter 3 Introducing BIOS Notice The BIOS options in this manual are for reference only Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard Users are welcome to download the latest BIOS version form our official website The BIOS is a program located on a Flash Memory on the motherboard This program is a bridge between motherboard and operating system When you start the computer the BIOS program will gain control The BIOS first operates an auto diagnostic test called POST power on self test for all the necessary hardware it detects the entire hardware device and configures the parameters of the hardware synchronization Only when these tasks are completed done it gives up control of the computer to operating system OS Since the BIOS is the only channel for hardware and software to communicate it is the key factor for system stability and in ensuring that your system performance as its best 3 1 Entering Setup Power on the computer and by pressing lt Del gt immediately allows you to enter Setup If the message disappears before your respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing lt Ct
17. be created Ipv6 PXE Support The optional settings are Disabled Enabled 38 Use this item to enable Ipv6 PXE Boot Support When set as Disabled Ipv6 boot optional will not be created PXE boot wait time Use this item to set wait time to press ESC key to abort the PXE boot CSM Configuration Press Enter to make settings for the following sub items Option ROM execution order Network This item controls the execution of UEFI and legacy PXE OpROM The optional settings are Do not launch UEFI only Legacy only Storage This item controls the execution of UEFI and Legacy Storage OpROM The optional settings are Do not launch UEFI only Legacy only Legacy first UEFI first Other PCI devices This item determines OpROM execution policy for devices other than Network storage or video The optional settings are UEFI first Legacy Only USB Configuration Press Enter to make settings for the following sub items USB Configuration Legacy USB Support The optional settings are Enabled Disabled Auto Enabled To enable legacy USB support Disabled To keep USB devices available only for EFI specification Auto To disable legacy support if no USB devices are connected XHCI Hand off This is a workaround for OSes without XHCI hand off support The ownership change should be claimed by XHCI driver The optional settings are Enabled Disabled 39 EHCI Hand
18. e INVERTER1 VCC 5V Bom _ allis m ride E B 2 3 Close INVERTER1 VCC 12V m mm em JP2 LVDS1 ele 5 ele 5 6 5 4 M 3 4l 95 4le 3 2 1 2 1 20 1 2 4 Close 3 4 Close 4 6 Close VCC 3 3V VCC 5V VCC 12V 3 pin INVERTER1 Back Light PWM DC Mode Select INVERTER 1 Back light 1 3 1 2 Close PWM Mode Selected nee 1 2 3 Close DC Mode Selected JP6 MPE1 Slot e Mii 1 2 Close MPE Slot VCC 3 3V Hi 2 3 Close MPE Slot VCC 3VSB JP5 4 pin COM1 Port Pin9 Function Select poz Id A 7 ell Pi a 1 e m A B en 5 JP5 COM1 Port 246 2 4 RI RS232 JP7 COM2 Header 6 N 29 5 2 4 Close RI RS232 3 1 3 4 Close RI 5V 4 6 Close RI 12V 6 5 ale 2 0 1 w 4 6 Close RI 12V JP8 4 pin COM3 Header Pin9 Function Select 6 ais 2 9 6 2116 JP8 COM3 Header 5 3 1 2 4 Close RI RS232 JP9 COMA Heade
19. e Parameters Select Screen th Select Item Enter Select Change Opt Fl General Help F2 Previous Values Optimized Defaults F4 Save 8 Exit ESCI Exit Press Enter to view current using memory information and make settings for the following sub items Intel IGD Configuration PAVC Use this item to enable or disable protected audio video control The optional settings are Disabled LITE Mode SERPENT Mode DVMT Pre Allocated Use this item to select DVMT 5 0 pre allocated fixed graphics memory size used 41 by the internal graphics device The optional settings are 64M 96M 128M 160M 192M 224M 256M 268M 320M 352M 384M 416M 448M 480M 512M DVMT Total Gfx Mem Use this item to select DVMT 5 0 total graphics memory size used by the internal graphics device The optional settings are 128M 256M MAX Aperture Size The optional settings are 128MB 256MB 512MB GTT Size The optional settings are 1MB 2MB IGD Turbo Enable The optional settings are Enabled Disabled Spread Spectrum Clock The optional settings are Enabled Disabled IGD Boot Type Use this item to select preference display interface used when system boot The optional settings are Auto CRT HDMI LVDS Note User needs to set Active LEP as Enabled otherwise the optional setting LVDS will not be available Active LVDS
20. elp F2 Previous value F3 Optimized defaults F4 Save amp Exit F7 To enter Boot Menu Press lt Esc gt to exit from the BIOS Setup 3 4 Getting Help Main Menu The on line description of the highlighted setup function is displayed at the top right corner the screen Status Page Setup Menu Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press lt Esc gt 3 5 Menu Bars There are six menu bars on top of BIOS screen Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Security Password settings Boot To change boot settings Save amp Exit Save setting loading and exit options 28 User can press the right or left arrow key on the keyboard to switch from menu bar The selected one is highlighted 3 6 Main Menu Main menu screen includes some basic system information Highlight the item and then use the lt gt or lt gt and numerical keyboard keys to select the value you want in each item Aptio Setup Utility t BIOS Information Set the Date Use Tab to BIOS Vendor American Megatrends switch between Date elements Core Version 5 009 Filename BFIUANO2 Bulld Date and Time 09 23 2014 10 46 53 Hed 01 2014 System Time 00 37 11 Access Level Administrator TXE
21. ettings are STD Printer Mode SPP Mode EPP 1 9 and SPP Mode EPP 1 7 and SPP Mode ECP Mode ECP and EPP 1 9 Mode ECP and EPP 1 7 Mode WatchDog Timer Use this item to enable or disable WatchDog Timer Control When set as Enabled the following sub items shall appear WatchDog Timer Value User can set a value in the range of 4 to 255 WatchDog Timer Unit The optional settings are Sec Min WatchDog Wake up Timer in ERP This item support WDT wake up while ERP function is set as Auto The optional settings are Enabled Disabled When set as Enabled the following sub items shall appear WatchDog Timer Value in ERP User can set a value in the range of 10 to 4095 WatchDog Timer Unit The optional settings are Sec Min ATX Power Emulate AT Power This item support Emulate AT power function MB power On Off control by power supply Use needs to select AT or ATX Mode on MB jumper at first ATX Mode amp 33 AT Mode Select Case Open Detect This item controls detect case open function The optional settings are Enabled Disabled PS2 KB MS Connect Use this item to set PS 2 connect primary device The optional settings are Keyboard First Mouse First PC Health Status Press Enter to view current hardware health status and make further settings in SmartFan Configuration SmartFan Configuration Press Enter to make settings for SmartFan Configuration Sma
22. ible settings Press Enter to make settings for the following sub items Out of Band Mgmt Port The default setting is COM1 This item may or may not show up depending on different configuration Terminal Type The optional settings are VT100 VT100 VT UTF8 ANSI Bits per second The optional settings are 9600 19200 57600 115200 Flow Control The optional settings are None Hardware RTS CTS Software Xon Xoff Data Bits 36 default setting is 8 This item may or may not show up depending on different configuration Parity The default setting is None This item may or may not show up depending on different configuration Stop Bits The default setting is 1 This item may or may not show up depending on different configuration CPU Configuration Press Enter to view current CPU configuration and make settings for the following sub items Limit CPUID Maximum The optional settings Disabled Enabled This item should be set as Disabled for Windows XP Execute Disable Bit The optional settings Disabled Enabled Hardware Prefetcher The optional settings are Disabled Enabled Use this item to enable the Mid Level Cache L2 streamer prefetcher Adjacent Cache Line Prefetch The optional settings are Disabled Enabled Use this item to enable prefetching of adjacent cache lines Intel Virtualization Technology The optional settings Disabled Enabled When se
23. le settings Press Enter to make settings for the following sub items Terminal Type The optional settings are VT100 VT100 VT UTF8 ANSI Bits per second The optional settings are 600 19200 38400 57600 115200 Data Bits The optional settings are 7 8 Parity The optional settings are None Even Odd Mark Space Stop Bits The optional settings are 1 2 Flow Control The optional settings are None Hardware RTS CTS VT UTF8 Combo Key Support The optional settings are Disabled Enabled Recorder Mode The optional settings are Disabled Enabled 35 Resolution 100x31 Use this item to disable or enable extended terminal resolution The optional settings are Disabled Enabled Legacy OS Redirection Resolution The optional settings are 80x24 80x25 Putty Keypad The optional settings are VT100 Linux XTERMRS SCO ESCN VT400 Redirection After BIOS POST The optional settings are Always Enable BootLoader Serial Port for Out of Band Management Windows Emergency Management Services EMS Console Redirection The optional settings are Enabled Disabled When set as Enabled user can make further settings in Console Redirection Settings Console Redirection Settings The settings specify how the host computer and the remote computer which the user is using will exchange data Both computers should have the same or compat
24. make settings for the following items Serial Port 1 Configuration Serial Port Use this item to enable or disable serial port COM Change Settings Use this item to select an optimal setting for super IO device Transmission Mode Select The optional settings are RS422 RS232 RS485 Mode Speed Select The optional settings are RS232 RS422 RS485 250kbps RS232 1Mbps RS422 RS485 10Mbps Serial Port FIFO Mode The optional settings are 16 Byte FIFO 32 Byte FIFO 64 Byte FIFO 128 Byte FIFO Serial Port 2 Configuration Serial Port 3 Configuration Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration Press Enter to make settings for the following items Serial Port 2 3 4 5 6 Configuration Serial Port Use this item to enable or disable serial port COM Change Settings Use this item to select an optimal setting for super IO device Serial Port FIFO Mode The optional settings are 16 Byte FIFO 32 Byte FIFO 64 Byte FIFO 128 Byte FIFO OS Select For Serial Port The optional settings Windows Linux Parallel Port Configuration Press Enter to make settings for the following items Parallel Port Configuration Parallel Port Use this item to enable or disable parallel port LPT LPTE Change Settings Use this item to select an optimal setting for super IO device Device Mode Use this item to change the printer port mode The optional s
25. r 5 3 1 2 4 Close RI RS232 6 4 2 5 3 1 3 4 Close RI 5V ee 46 2 5 3 1 3 4 Close RI 5V 2 po 4 6 Close RI 12V 2 po 4 6 Close RI 12V w wo JP10 4 pin COM5 Header Pin9 Function Select JP10 COM5 Header eje 5 6e 5 6 5 4 E 3 4 96 4 3 20 1 2 1 260 1 2 4 Close 3 4 Close 4 6 Close RI RS232 RI 5V RI 12V JP11 4 pin COM6 Header Pin9 Function Select ez H B JP11 COM6 Header SID cle 5 6 e 5 6 5 4890 3 4 4 2 1 2 1 22 1 2 4 Close 3 4 Close 4 6 Close s 8232 RI 5V RI 12V JBAT1 2 pin Clear CMOS RAM Setting JBAT1 Clear CMOS 1 2 Open Normal 18e 2 3 Close Clear CMOS JP12 Disable ME Function 1 1 2 Open Normal 1 1 2 Close Disable ME Function Selected Pin 1 amp 2 of JP14 4 pin AT Mode Function Select He S 5 4 2 p ZI ere a 6088 o REC an 3 Pin 1 amp 2 of JP14 AT Mode Select A ee Pin
26. rl gt lt Alt gt and Delete keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press lt gt to enter Setup 3 2 BIOS Menu Screen The following diagram show a general BIOS menu screen Setup Utility BIOS Information BIOS Vendor Core Version Filename Build Date and Time American Megatrends 5 009 BF SUAAOZ 09 29 2014 10 46 53 Wed 701 2014 Systen Tine 00 97 11 Access Leve Administrator TKE Information TXE FH Version 01 01 00 1089 Current Setting Value Function Keys Menu Items Menu Bar Set the Date Use Tab to switch between Date elements General Help Items Select Screen th Select Item t Select Change Opt General Help F2 Previous Values F3 Optimized Defaults Save 8 Exit ESC Exit BIOS Menu Screen 3 3 Function Keys In the above BIOS Setup main menu of you can see several options We will explain these options step by step in the following pages of this chapter but let us first see a short description of the function keys you may use here Press left right to select screen 27 e Press N up down to choose in the main menu the option you want to confirm or to modify Press Enter to select Press lt gt lt gt keys when you want to modify the BIOS parameters for the active option F1 General h
27. rtFan Configuration CPUFAN SYSFAN1Type The optional settings are 4 Pin 3 Pin CPUFAN SYSFAN1 2 Smart Mode The optional settings are Disabled Enabled When set as Enabled the following sub items shall appear CPUFAN SYSFAN1 2 Full Speed Temperature Use this item to set CPUFAN SYSFAN1 2 full speed temperature Fan will run at full speed when above this pre set temperature CPUFAN SYSFAN1 2 Full Speed Duty Use this item to set CPUFAN SYSFAN 1 2 full speed duty Fan will run at full speed when above the pre set duty CPUFAN SYSFAN1 2 Idle Speed Temperature Use this item to set CPUFAN SYSFAN1 2 idle speed temperature Fan will run at idle speed when below this temperature CPUFAN SYSFAN1 2 Idle Speed Duty Use this item to set CPUFAN SYSFAN 1 2 idle speed duty Fan will run at idle speed when below the pre set duty Shutdown Temperature Configuration Use this item to select system shutdown temperature The optional settings are Disabled 70 C 158 F 75 C 167 F B0 C 176 85 C 185 F Serial Port Consol Redirection Press Enter to make settings for serial port redirection settings COM1 Console Redirection The optional settings are Disabled Enabled When set as Enabled user can make further settings in Console Redirection Settings The settings specify how the host computer and the remote computer which the user is using will exchange data Both computers should have the same or compatib
28. store load default values for all the setup options 46 Save as User Defaults Use this item to save the changes done so far as user defaults Restore User Defaults Use this item to restore defaults to all the setup options Boot Override UEFT Built in EFI Shell Launch Internal EFI shell application shell efi Lauch EFI Shell from filesystem device Use this item to launch EFI shell application shell efi from one of the available filesystem device Reset System with TXT disable Mode Press Enter for TXE to run into the temporary disable mode Ignore if TXE Ignition FM
29. t as Enabled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology EIST The optional settings Disabled Enabled Use this item to enable or disable Intel SpeedStep CPU C6 Report Use this item to enable or disable CPU C6 ACPI C3 report to OS 37 The optional settings Disabled Enabled CPU C7 Report Use this item to enable or disable CPU C6 ACPI C3 report to OS The optional settings Disabled Enabled Package C state Limit The optional settings CO C1 C3 C6 C7 No Limit SATA Configuration Press Enter to make settings for the following sub items SATA Configuration SATA Port The optional settings are Enabled Disabled SATA Mode The optional settings are IDE Mode AHCI Mode SATA Speed Support The item is for user to set the maximum speed the SATA controller can support The optional settings are Gen1 Gen2 SATA Port1 The optional settings are Enabled Disabled mSATA SATA Port2 The optional settings are Enabled Disabled Network Stack Configuration Press Enter to go to Network Stack screen to make further settings Network Stack The optional settings are Enabled Disabled When set as Enabled the following sub items shall appear 4 PXE Support The optional settings are Disabled Enabled Use this item to enable 4 PXE Boot Support When set as Disabled Ipv4 boot optional will not
30. tate 011 65535 0xFFFF means indefinite Quiet Boot Disabled Boot Option Priorities Boot Option 1 BullteIn EFI Select Screen thi Select Item Enter Select Change Opt Fl General Help F2 Previous Values Optimized Defaults Fai Save 8 Exit ESC Exit Boot Configuration Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key Bootup Numlock State Use this item to select keyboard numlock state The optional settings are On Off Quiet Boot The optional settings are Disabled Enabled Boot Option Priorities Boot Option The optional settings are UEFI Built in EFI Shell Disabled 3 11 Save amp Exit Menu Aptio Setup Utility Save amp Exit Reset the system after saving Discard Changes and Reset the changes Restore Defaults Saye as User Defaults Restore User Defaults Boot Override Built in EFT Shell Launch EFI Shell from filesystem device Reset System with TXE disable Mode Select Screen th Select Item Enter Select Change Opt FL General Help F2 Previous Values Optimized Defaults Fas Save amp Exit ESC Exit Save Changes and Reset This item allows user to reset the system after saving the changes Discard Changes and Reset This item allows user to reset the system without saving any changes Restore Defaults Use this item to re
Download Pdf Manuals
Related Search