Owner/User Manual
Contents
1. Model APS 622E GE Owner s Manual 3 Channel Remote Car Starter 2 Three Button Programmable RF Transmitters Three Channel Receiver capable of accepting 4 transmitters External Superheterodyne Receiver Antenna w Push Button Switch and LED Keyless Entry Outputs Trunk Release Output On Board Start Relay On Board Accessory Relay On Board Ignition 1 Relay On Board Ignition 2 Relay Ignition 2 Relay Selectable On or Off During Cranking On Board Parking Light Relay Ignition 3 Shock By Pass GM VAT Output relay required Tach Signal Learning Circuit Two and Two Safety Shutdown Circuits Alarm By Pass Output Accessory Outputs Pulse Before amp After Start During Crank amp After Shut Down Selectable Steady or Flashing Parking Lights for Run Indication Selectable 5 10 15 20 45 amp 60 Minute Run Time Selectable 1 Sec 3 5 Sec or 1 Sec Dbl 1 Sec Door Lock Output Pulse Car Finder Mode KEYLESS ENTRY The Lock button on the transmitter is used to lock the vehicle s doors the Unlock button is used to unlock the vehicle s doors To lock or unlock the doors simply press and release the desired function button one time As a keyless entry unit for your convenience the parking lights will flash and the horn will beep once when the doors are locked and twice when the doors are unlocked REMOTE CAR FINDER The Lock or Unlock buttons are also2. With the system disarmed Press and Hold the Push Button found on the windshield receiver in 2 Turn the ignition switch on off on off on off 3 The LED turns off indicating that the R S unit is fully functional one again 128 9350 2 of 4 PROGRAMMED TRANSMITTER NOTIFICATION PTN Every time after Disarm when the ignition key is turned on the unit s LED will re port the number of transmitters programmed into the system This safety feature will alert you if an unauthorized transmitter has been programmed into your vehicle s security system without your knowledge Typically from the factory there will be 2 flashes and a pause repeated 3 times ee that two trans mitters are programmed into the system If you note additional flashes an addi tional transmitter may have been added without your knowledge or authorization If you notice a change in the transmitter LED report pattern you can correct this by looking up how to erase and reprogram your transmitters found in the trans mitter programming guide This reprogram operation will erase all unauthorized or unwanted transmitters PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS BANK 1 Transmitter Model Name 3BP Is Also Found On Back Of Transmitter Case And Uses CR2032 Battery 1 Turn the aie key to the ON position 2 Press and release the valet programming switch 3 times Siren Chirps 3 Press the Lock Button of each transmitter you want programmed until you hear a ch
3. 2 priority In this situation the unlock button can be programmed into two receiver channels unlock channel 2 and driver priority 6 or 7 In no other circum stance will the system allow a transmitter button to be programmed into 2 receiver channels at the same time 128 9350 3 of 4 Transmitter Battery Replacement 1 Remove the 0 point Philips head screw from the rear of the transmitter case 2 Separate the transmitter halves being careful not to drop the transmitter contents 3 Slide the CR 2032 battery from the battery holder paying attention to the battery orientation 4 Replace the battery with a new one and reassemble the case in reverse of disassembly FUNCTION SETTING CHART To be completed by installer Run Time Min O Door Lock Timer Sec O Parking Lights Pulse O Steady O WARNING Arunning vehicle produces dangerous carbon monoxide gas which can be fatal if prolonged exposure occurs Be certain the vehicle is outdoors before activat ing the remote start function FCC COMPLIANCE qnis device complies with Part 15 of the FCC rules and with RSS 210 of Industry anada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including any interference that may cause undesired operation Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user
4. s authority to operate the equipment NOTE The manufacturer is not responsible for any radio or TV interference caused y unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment PATENTED www voxxintl com company patents To purchase replacement transmitters or to get additional product information go to www prestigecarsecurity com 2014 Voxx Electronics Corporation 150 Marcus Blvd Hauppauge NY 11788 128 9350 128 9350 4of4
5. used to access the car finder mode This feature is particularly useful in a crowded parking lot here finding your car may be difficult To access the car finder mode while within range of your car simply press and hold either the lock or unlock button of your transmitter for three seconds The parking lights will begin to flash and the horn will beep making your vehicle more visible The lights will stop automatically after 30 seconds If you wish to turn off the car finder mode prior to the expiration of the 30 second timer press and release either the lock lor unlock button of your transmitter one time PATENTED www voxxintl com company patents 128 9350 1 of 4 REMOTE TRUNK RELEASE If you have electric trunk release in your vehicle and the remote trunk release option was added to your vehicle simply press and hold the Key Trunk button of your keychain transmitter for 4 seconds or until the electric trunk of your vehicle opens REMOTE STARTING THE VEHICLE This unit will not start the vehicle if any one of the following situations exist The vehicle s hood lid is opened The gear shift selector is not in Park The brake pedal is depressed The safety control switch is in the OFF position To start the vehicle press and release the Key Trunk button two times within 2 seconds The vehicle will start and remain running for the pre programmed 5 10 15 20 minute run cycle As a visual indication the parking lights will f
6. irp from the horn or siren 4 Turn the ignition switch to the OFF position The above action programs the Lock Unlock Start Trunk and Option 1 buttons which are typical for most systems For additional channel programming beyond the 1 option button you can use any unused button or combination of buttons not in use In other words to access option channel 5 6 7 you would do the following From step 3 above a Press and release the valet programming button 4 additional times to get to channel 5 then Press any unused transmitter button or button combination to rogram b From a press and release the valet programming button 1 time to get to channel 6 then press any unused transmitter button or button combination to program c From b press and release the valet programming button 1 time to get to channel 7 then press any unused transmitter button or button combination to program NOTE Not all systems have channels above 3 check with your installation center for options your system may or may not have NOTE Certain systems have the ability to utilize channels 6 amp 7 for driver priority programming For driver priority the vehicle must be equipped with this feature and the optional feature must be set up and installed by your installation center Once this feature is added when the unlock button of transmitter 1 is used it will set driver 1 priority and when the unlock button of transmitter 2 is used it will set driver
7. lash or remain on depending on the setting by your installation center When you arrive at the vehicle turn the ignition key to the ON position not the spring loaded start position then step on the brake pedal to disengage the remote starter The vehicle will continue to run but now on its own power NOTE The engine will stop running before the pre programmed run cycle has expired if you perform any one of the eel functions Press andrelease Key Trunk button on the keychain transmitter two times within 2 seconds Depress the brake pedal Open the vehicle s hood Place the unit in the safety control disabled mode PUSH BUTTON LED RECEIVER VADE ela ae cae aa CONTROL The Push Button LED switch located in the receiver allows you to temporarily dis able the remote starting function of the system This is recommended whenever the vehicle is being serviced To place the system in the service mode 1 With the system disarmed unlocked and the ignition switch off press and hold the Push Button found on the wind shield receiver in 2 Turn the ignition switch on off on off on off 3 The LED begins to flash two short flashes followed by one long flashes and continues this pattern until returned to normal mode of operation This puts the unit into the R S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise To Exit R S Override Mode 1
Download Pdf Manuals
Related Search