Home

English-US

1. 33 Water and Moisture Use only products designed for outdoor environments where they will be exposed to water or moisture 34 Accessories Do not place the unit on an unstable surface to avoid falling Use only UL Listed Vicon recommended mounting accessories 35 Ventilation Do not block ventilating slots and openings as they ensure reliable operation Do not place the unit near a heat source or into an enclosure unless recommended by Vicon 36 Grounding Only products equipped with a 3 prong grounded plug should be inserted into a grounded power outlet Contact an electrician to replace an obsolete outlet Do not force a plug into a non grounded outlet 37 Power Cord Protect on Power supply cords should not be routed in trafficked areas or in tight spaces where they will be pinched or used to bear weight Allow some slack in the cord where it enters the unit 38 Lightning Disconnect the product from its power source and cable system when possible to prevent damage due to lightning and power line surges 39 Power Lines e Do not locate outside cables over power or utility lines where they can fall and make direct contact Contact with power lines can be fatal 40 Overloading Do not overload wall outlets and extension cords to prevent risk of fire and electric shock 41 Object and Liquid Entry Never probe through or spill liquid into enclosure openings to prevent risk of fire or electric shock 42
2. All devices requiring a separate power supply shall be powered by a UL Listed Class 2 Power Supply 49 Lithium Batteries Only WARNING Fire and burn hazard Do not recharge disassemble heat above 212 F or incinerate Keep battery out of reach of children and in original package until ready to use Dispose of used batteries promptly Risk of explosion if battery is replaced by incorrect type Dispose of used batteries according to the instructions 50 For Rack Mounted Units Only The following precautions apply to all rack mounted units a Elevated Operating Ambient If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature Tma specified by the manufacturer Da Important Safeguards Indoor Use Cont b Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised c Mechanical Loading Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading d Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overc
3. The lightning bolt symbol alerts the user to the presence of dangerous voltage that may present the risk of electric shock CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point symbol alerts the user to the presence of important operating and maintenance instructions WARNING To reduce a risk of fire or electric shock do not expose this product to rain or moisture 26 Read Instructions Read all safety and operating instructions before the product is operated 27 Retain Instructions Retain all safety and operating instructions for future reference 28 Heed Warnings Pay attention to all product warnings 29 Follow Instructions Follow all operating instructions 30 Installation and W iring The equipment and all devices connected to it shall be installed and wired in accordance with the National Electrical Code ANSI NFPA 70 31 Cleaning Do not use caustic abrasive or aerosol cleaners a For units that CAN BE DISCONNECTED from the power source use a damp cloth for cleaning b For units that CANNOT BE DISCONNECTED from the power source use a damp cloth for cleaning and do not allow moisture or liquids to enter vents 32 Attachments Use only UL Listed Vicon recommended attachments to prevent unit damage and personal injury
4. and HDMI2 2 Unavailable in Component mode and PAL system Controls and functions B Picture Sound Picture Sound Picture Sound A V MOVE ENTER MENU RETURN A V MOVE ENTER MENU RETURN 3D Comb Activates the 3D comb filter PC See table below 1 Unavailable in RGB PC DVI HDMI1 and HDMI2 2 Unavailable in S Video RGB PC DVI HDMI1 HDMI2 and Component 3 Only available in RGB PC Picture Mode Custom Applies user selected values Brightness Contrast Color Tint and Sharpness Dynamic Provides enhanced contrast and sharpness Standard Provides standard contrast and sharpness Movie Is recommended for viewing film based content Mild Reduces contras and sharpness 10 Controls and functions Color Tone Cool Gives the white color a bluish tint Normal Gives the white color a neutral tint Warm Gives the white color a reddish tint User To manually adjust the color tones Red Green and Blue Size Wie 1 Unavailable in RGB PC DVI HDMI1 HDMI2 and Component 2 Unavailable in RGB PC PC Picture Sound A V MOVE ENTER MENU RETURN Option Function Value Auto Adjust Auto geometry adjustment Phase Adjusts the number of horizontal picture elements O 100 H Position Adjusts the horizontally picture position O 100 V Position Adjusts the vertically picture position O 100 Frequency Adjusts the vertical noise of sc
5. and LED is lit Check that the Brightness and or the Contrast adjustments of the Display have not been turned down to minimum levels NO SIGNAL The signal cable should be completely message on screen connected to the video card computer The video card should be completely seated in its slot and the computer is switched ON Display image is not centered too small or too large in PC mode Vertical or Horizontal noise is present in the picture Adjust Clock and Phase in the OSD Push the down key in front side or Auto key in rernote controller WEEE Symbols Correct Disposal of This Product Waste Electrical 8 Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract T
6. of four stages On Green and Unsupported mode Green MODE LED COLOR MONITOR OPERATION ON GREEN Normal Operation UNSUPPORTES GREEN Normal operation but the on screen MODE Display will show error massage POWER OFF RED Not Operation 18 Specifications ore 32 Diagonal AM TFT yP Active Matrix Pixel pitch mm 0 36375 H x 0 36375 V LCD BRIGHTNESS 350cd m Typical Type E 3000 1 Typical RATIO VIEWING ANGLE 178 178 H V RESPONSE TIME 6 5msec Gray to Gray RESOLUTION H x V 1920X1080 60Hz VIDEO 2ch input 1 0Vp p 750 terminated loop through out S VIDEO 1ch input Y C loop through out COMPONENT Y Pb Pr Sound L R DVI Digital Video Interface INPUT SIGNAL HDMI1 HDMI2 High Definition Multimedia Interface PC RGB AV composite Sound in Out PC Stereo Sound Audio Out 698 4 X 392 85 mm ACTIVE DISPLAY AREA W x H PACKING DIMENSIONS 790mm x 580mm x 220mm W x H xD 31 10 x 22 83 x 8 66 13 kg 28 66 Ibs WEIGHT 17 3 kg 38 14 lbs ELECTRICAL RATINGS 100 240V 50 60Hz Auto Switching gt gt NOTE Technical specifications are subject to change without notice 19 Troubleshooting guide TROUBLE TROUBLESHOOTING TIP No image on display screen Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip Power switch should be in the ON position
7. of three years with the following exceptions 1 Monitors all models One year from date of original retail purchase 2 Uninterruptible Power Supplies Two years from date of original retail purchase 3 VDR 700 Recorder Series One year from date of original retail purchase 4 V5616MUX One year from date of original retail purchase 5 Arecont Cameras One year from date of original retail purchase 6 FMC series fiber optic media converters and associated accessories Lifetime warranty 7 For PTZ cameras Normal Use excludes prolonged use of lens and pan and tilt motors gear heads and gears due to continuous use of autopan or tour modes of operation Such continuous operation is outside the scope of this warranty 8 Any product sold as special or not listed in Vicon s commercial price list One year from date of original retail purchase Date of retail purchase is the date original end user takes possession of the equipment or at the sole discretion of the Company the date the equipment first becomes operational by the original end user The sole remedy under this Warranty is that defective equipment be repaired or at the Company s option replaced at Company repair centers provided the equipment has been authorized for return by the Company and the return shipment is prepaid in accordance with policy The Company will not be obligated to repair or replace equipment showing abuse or damage or to part
8. the Component mode Controls and functions FRONT KEY CONTROL SOURCE MENW y a lt gt o ee I 1 2 3 4 5 6 7 1 SOURCE SELECT Select PC or video Select On Screen Display menu 2 MENU EXIT Activate and exit the On Screen Display 3 VIA These buttons allow user to enter the sub menu of the activated function The up A button is HOLD function and stop the Trigger amp Auto switching functions 4 lt gt Adjust the volume and menu settings 5 POWER ON OFF I Turns the power ON or OFF There will be a few seconds delay before the display appears 6 POWER LED The power LED lights with green when the power is turned ON The power is turned off by pressing the power switch again and the power LED goes Red 7 IR Sensor Remote controller sensor Controls and functions OSD MENU DESCRIPTION All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen 1 Press the Menu button to enter the OSD menu 2 Press the A V buttons to select the desired option The selected option is highlighted 3 Press the D button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the lt gt buttons 5 Press the lt button to exit the submenu for adjusting items 6 Press the Menu button to exit the OSD menu A Custom Brightness 50 MOON AS A AA AI MENU RETURN 1 Unavailable in RGB PC DVI HDMI1
9. Installation and Operation Manual XX 204 70 00 VM 632LED High Definition LED Monitor C LISTED Commercial CCTV Video Equipment 2C88 Vicon Industries Inc 131 Heartland Boulevard Edgewood NY 11717 Tel 631 952 2288 Fax 631 951 2288 Toll Free 1 800 645 9116 24 Hour Technical Support 800 34 VICON 800 348 4266 UK 44 0 1489 566300 Vicon Industries Inc does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation This system has not been designed to be used in life critical situations and must not be used for this purpose www vicon security com Document Number 8009 8204 70 00 Issued 0614 Product specifications subject to change without notice Copyright 2014 Vicon Industries Inc All rights reserved Contents PORE ANG SaregUards mai 23 PPP e ME BUE E 4 ECO NOCO area Op A e a E E ETE 5 Connecting with external equipment e ee 6 Remote TUNCUONS uam adiar irei een ni a a 7 Controls and TECLA 8 15 Mounting Gude ee are 16 D SUB connector pin assignment u a 17 Power management serrana actrices N REFER vrs 18 e Seren een een er A AAA ase e ANEA rare 19 Toubisshooting quIde epocas 20 SHIPPING ISU CU ONS een 21 o e e lo o Eo O A 22 This Monitor was Manufactured by ISO 9001 Certified Factory Important Safeguards Indoor Use GRAPHIC SYMBOL EXPLANATION
10. L VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising Do not cover the unit or place anything on the top of unit gt AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance gt TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor gt BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord Damage to a power cord can cause fire or electrical shock FCC Notice Note Complies with Federal Communications Commission Rules amp Regulations Part 15 Subpart B for a Class A digital device WARNING This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instruction may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 ofthe FCC rules which are designed to provide reasonable protection against such interference in a commercial installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio and television reception which can be determined by turning equipment off and o
11. Servicing Refer all servicing to qualified service personnel 43 Damage Requiring Service Obtain service when a The power supply cord or plug is damaged b Objects have fallen or liquid has been spilled into the product c The product is not designed for outdoor use and has been exposed to water or moisture d The product does not operate per the operating instructions Perform Vicon recommended adjustments modifications and troubleshooting only to avoid unit damage and personal injury e The product has been dropped f The product shows a significant change in performance 44 Replacement Parts Use only Vicon specified replacement parts or an approved equivalent to prevent unit damage and injury 45 Safety Check Request safety checks to be performed following repair or maintenance to verify proper operation 46 ESD Precaution Take all normal electrostatic discharge precautions to avoid component damage during installation and operation 47 For 230 VAC Devices Only When the disconnect device is not incorporated in the equipment or when the plug on the power supply is intended to serve as the disconnect device follow the guidelines below a For permanently connected 230 VAC units a readily accessible disconnect device must be incorporated into the site wiring b For 230 VAC units with a plug the outlet must be installed near the unit and be easily accessible 48 For Devices Requiring a Separate Power Supply
12. V2 OUT AV2 IN AV1 OUT AV1 IN DC12V OUT CAMERA USE AC IN POWER Remote functions REMOTE CONTROLLER Optional 1 POWER Turns the power ON or OFF There will be a few seconds delay before the display appears SOURCE Selects an input source AUTO Auto geometry adjustment in the RGB PC source HOLD Stops the Trigger amp Auto switching functions MUTE Mutes the sound MENU Activates and exits the On Screen Display EXIT Exits the On Screen Display VOL lt amp gt Increases or decreases the level of audio volume UP DOWN Moves upwards or downwards in the OSD menu 10 ENTER Enters an OSD submenu or accepts your selection 11 INFO Displays the information about input source 12 STILL Pauses the picture 13 PIP Picture In Picture Activates the PIP mode 0 m N p m A AN 14 PINPUT Changes the source of sub picture in the PIP mode 15 P POS Changes the position of sub picture in the PIP mode 16 P SIZE Changes the sizes of sub and main pictures in the PIP mode 17 SWAP Alternates between sub and main pictures in the PIP mode 18 ARC Aspect Ratio Control Selects a screen ratio 19 APC Auto Picture Control Selects a picture mode 20 ACC Auto Color Control Selects a color mode 21 S SET Selects the source of sound between main and sub pictures in the PIP mode 22 PC Selects a PC mode PC DVI amp HDMI 23 AV Selects an AV mode AV1 AV2 amp S Video 24 COMP Selects
13. hall be enforceable against the Company only in the courts located in the State of New York The form of this Warranty is effective May 4 2012 THE TERMS OF THIS WARRANTY APPLY ONLY TO SALES MADE WHILE THIS WARRANTY IS IN EFFECT THIS WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE COMPANY S WEBSITE WWW VICON SECURITY COM IN THAT EVENT THE TERMS OF THE POSTED WARRANTY SHALL APPLY EXCLUSIVELY 2 MEMO Vicon Industries Inc VICON INDUSTRIES INC 131 HEARTLAND BLVD EDGEWOOD NY 11717 8315 www vicon security com 631 952 2288 1 800 645 9116 Fax 631 951 2288 Vicon Europe Headquarters Brunel Way Fareham PO15 5TX United Kingdom 44 0 1489 566300 Fax 44 0 1489 566322 Vicon Germany Kornstieg 3 D 24537 Neumuenster Phone 49 0 4321 8790 Fax 49 0 4321 879 97 Far East Office Unit 5 17 F Metropole Square 2 On Yiu Street Shatin New Territories Hong Kong 852 2145 7118 Fax 852 2145 7117 Internet Address www vicon security com L39ME0360_REV 01
14. his product should not be mixed with other commercial wastes for disposal 20 Shipping Instructions Use the following procedure when returning a unit to the factory 1 Call or write Vicon for a Return Authorization R A at one of the locations listed below Record the name of the Vicon employee who issued the R A Vicon Industries Inc 131 Heartland Boulevard Edgewood NY 11717 Phone 631 952 2288 Toll Free 1 800 645 9116 Fax 631 951 2288 For service or returns from countries in Europe contact Vicon Industries U K Ltd Brunel Way Fareham PO15 5TX United Kingdom Phone 44 0 1489 566300 Fax 44 0 1489 566322 2 Attach a sheet of paper to the unit with the following information Name and address of the company returning the unit Name of the Vicon employee who issued the R A R A number Brief description of the installation Complete description of the problem and circumstances under which it occurs Unit s original date of purchase if still under warranty Q h D G C C 3 Pack the unit carefully Use the original shipping carton or its equivalent for maximum protection 4 Mark the R A number on the outside of the carton on the shipping label lt 94 Vicon Standard Equipment Warranty Vicon Industries Inc the Company warrants your equipment to be free from defects in material and workmanship under Normal Use from the date of original retail purchase for a period
15. n the user is encouraged to try and correct the interference by one or more of the following measures Reorient the receiving antenna Relocate the equipment with respect to the receiver Relocate the equipment away from the receiver Plug the equipment into a different electrical outlet so that the equipment and receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook Bulletin CIB 2 This booklet is available from the U S Government Printing Office Superintendent of Documents Mailstop SSOP Washington D C 20402 9328 ISBN 0 16 045542 1 N Warning Power must be removed from this unit before removing circuit modules or cables ZN Caution This unit contains circuit cards with integrated circuit devices that can be damaged by static discharge Take all necessary precautions to prevent static discharge Connecting with external equipment BACK PANEL CONTROL HERRIN 6 76 9 10 11 12 13 14 15 16 17 18 TRIGGER INPUT COMPONENT AUDIO L R IN amp COMPONENT Y Pb Pr IN Sea Se A EU A os ek ks Gk os ok sa G8 CON OOF YN O AUDIO OUT Speaker PC AUDIO IN PC RGB IN DVI IN HDMI1 IN HDMI2 IN AV2 AUDIO R L IN AV1 S VIDEO AUDIO RIL IN S VIDEO OUT S VIDEO IN A
16. n Detection Built in PIR sensor Passive Infra Red ig PIP amp FULL 4 MOVE ENTER MENU RETURN Option Function Value Trigger Enable Activates the trigger feature Off or On AV1 AV2 S Video RGB PC Trigger Input Selects the input source for the Trigger DVI HDMI1 HDMI2 and Component Activates an audible signal when the monitor Buzzer l On or Off receives an trigger signal l l Selects the amount of time in seconds Trigger Time l l 3 100 that the monitor displays the trigger Input image Trigger Option Selects the type of physical trigger input See table below Selects the mode in which the monitor displays the Trigger Input The monitor takes one of the following actions PIP amp FULL Displays the Trigger Input in the PIP l of the current video input source Display Type o PIP amp FULL or FULL Note The main video source must support the Trigger Input source as a PIP option See section Input Source in C PIP FULL Switches the display to show the Trigger Input in the full screen 14 Controls and functions N C Normally Closed The Trigger function is activated when the trigger cable is opened N O Normally Opened The Trigger function is activated when the trigger cable is closed High The Trigger function is activated when the trigger signal is DC 2 5 V Low The Trigger function is activated when the trigger
17. ormation Displays a blue screen if the monitor Blue Screen Off or On receives no signal i Locks all buttons of the monitor Key Lock Off or On Note Use remote controller to unlock Trigger See table below Auto Switching See table below Image Rotation Activates the Image Rotation function 1 How to unlock On the front key Press the MENU and A button at the same time over 3 seconds On the Remote Controller The Remote Controller operates well because the Key Lock function is only allowed for the front key of this product 2 The displayed image is slightly moved to prevent image persistence when the Image Rotation function is On The user is able to adjust the image rotation time from 0 10Min in the sub menu of image rotation Image persistence When an LCD panel is continuously displaying the same image graphic for a long period of time a trace of the image can remain visibly Image persistence is not a product defect and all LCD products are subject to image persistence AI Controls and functions NOTICE When watching moving images on a computer or a DVR through this monitor using a PC RGB DVI or HDMI input you can see blurred images on the edge of icons and pop up windows but this is not a defect The blur may appear on the fixed images such as another icon and pop up window because the 120Hz feature is focused on fast moving images to enhance the quality of moving image Motio
18. reen image O 100 11 Controls and functions A V MOVE amp ENTER MENU RETURN Option Function Value PIP Activates the PIP feature Off or On Input Source Selects the input source for the PIP area See table below Enables 3 screen size 4 3 side by corner 4 3 side by 4 3 PIP Mode l l PIP PBP1 or PBP2 and full screen side by side PIP Size Selects the size of PIP screen Size1 Size2 or Size3 Selects the position of PIP screen Right of Bottom Left of Position RB LB LT or RT Bottom Left of Top and Right of Top Swap Alternates between the main and sub picture Sound Select Selects the sound source from either the Main or PIP Main or Sub Input Source ain sd AV1 AV2 or S Video AV1 AV2 or S Video RGB PC DVI HDMI1 HDMI2 Available AV1 AV2 or S Video or Component combination RGB PC DVI HDMI1 HDMI2 AV1 AV2 or S Video or Component Unavailable RGB PC DVI HDMI1 HDMI2 RGB PC DVI HDMI1 HDMI2 combination or Component or Component 12 Controls and functions D Setup English Transparency off off X X A V MOVE ENTER MENU EXIT Option Function Value Resets the monitor settings to their Reset factory default English French Deutsch Language Sets the language of the OSD menu Italian Spanish Portuguese or Nederland Changes background of monitor menus OSD Tone l l Transparency or On e g input source amp inf
19. s which in the judgment of the Company are not defective or any equipment which may have been tampered with altered misused or been subject to unauthorized repair Software supplied either separately or in hardware is furnished on an As Is basis Vicon does not warrant that such software shall be error bug free Software support via telephone if provided at no cost may be discontinued at any time without notice at Vicon s sole discretion Vicon reserves the right to make changes to its software in any of its products at any time and without notice This Warranty is in lieu of all other conditions and warranties express or implied as to the Goods including any warranty of merchantability or fitness and the remedy specified in this Warranty is in lieu of all other remedies available to the Purchaser No one is authorized to assume any liability on behalf of the Company or impose any obligations on it in connection with the sale of any Goods other than that which is specified above In no event will the Company be liable for indirect special incidental consequential or other damages whether arising from interrupted equipment operation loss of data replacement of equipment or software costs or repairs undertaken by the Purchaser or other causes This warranty applies to all sales made by the Company or its dealers and shall be governed by the laws of New York State without regard to its conflict of laws principles This Warranty s
20. signal is DC 0 0 6 V Note In this case trigger port has high status electrically so the trigger cable has to have ground or earth status to be activated Auto Switching LVA AN ENTER MENU RETURN Option Function Auto Switching Activates the Auto Switching feature Opens another menu and you can select the input Input Enable no sources to include in the Auto Switching cycle Selects the amount of time in seconds that the Time monitor displays each selected input source Age Value Off or On AV1 AV2 S Video RGB PC DVI HDM1 HDMI2 and Component 3 100 Mounting Guide Wall mounting Optional The LCD monitors are suitable for VESA standard wall mount not included in the delivery lt 32 inch gt e 32 inch VESA 200mm x 200mm Attention You must use four M6x8 screws to assemble this monitor and the wall mount bracket Warning If user use longer than M6x8 32inch it may cause the damage on the unit Please follow instructed bolt size amp length 16 D SUB connector pin assignment gt PIN ASSIGNMENTS D SUB gt ACCESSORIES Power cord User s manual HDMI cable Trigger cable Stereo cable Remote controller Batteries Wall mount Option Oe See YS AT Power management POWER CONSUMPTION MODE POWER CONSUMPTION lt 55W POWER OFF lt 1W LED INDICATOR The power management feature of the monitor is comprised
21. urrent protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern e Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips Cautions CAUTION The power supply cord is used as the main disconnect device ensure that the socket outlet is located installed near the equipment and is easily accessible ATTENTIONN Le cordon d alimentation est utills comme interrupteur g n ral La prise de courant doit tre situ e ou install e proximit du mat riel et tre facile d acc s CAUTION TO SERVICE PERSONNEL POWER SUPPLY CORD 15 USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRODUCT UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING EMISSION CHARACTERISTICS TESTED BY SEMKO THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990 10 MPR gt NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel gt DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard do not expose the unit to rain or moisture This unit is designed to be used in the office or home Do not subject the unit to vibrations dust of corrosive gases gt KEEP IN A WEL

English-US

Contents

Download Pdf Manuals

Related Search

Related Contents