HL 675 Data / Impulse Transmitter set User Manual
Contents
1. TAGHeuer PROFESSIONAL TIMING HL 675 Data Impulse Transmitter set User Manual Version 02 2015 TAGHeuer Timin Page 1 8 1 Global The Set HL 675 is ideal for transferring Timing Data and Impulses Its 500mW emitting power and its licence free frequency range 869 Mhz makes this device a powerful and simple to use system gt Data Impulse transmission system 500 Mw which does not require a licence free of use in Europe ISM Band 869 MHz REC 70 03 Each Receiver can receive Impulses simultaneously or not from 4 Transmitters identified by the function CHANNEL 1 to 4 Up to 4 Teams can work train in the same area without disturbing each other thanks to the function TEAM which offers the possibility to code each system A B C D lt is also possible to use up to 16 transmitters with 4 receivers When the receiver is switched on it is possible that one or more green LED s are on before that the transmitter s start to transmit This detection system allows visualization of the quality of the received signal but also the possible interferences coming from other radio transmission systems If it is not possible to stop these interferences by moving the receiver the transmission of Impulse cannot be guaranteed TAGHeuer Timin Page 2 8 1 Functions 1 1 The Transmitter u IMPULSE 2 DATA 2 POWER 4 SET 5 TEAM 6 CHANNEL 7 TEST 8 TEST BATT 9 LED 10 LED2. 11 CHARGE Input for timing Impulse Start gate photocell working closing contact Respect the polarities Male Sub D 9 RS232 input for DATA transfer To switch on the receiver press for 3 seconds on POWER The green LED is on To switch off the receiver hold down SET and press POWER To program the TEAM A B C D and to switch off the receiver Hold down SET during the changes To check the programmed TEAM To change the code hold down SET and press TEAM To check the programmed CHANNEL To change the CHANNEL hold down SET and press CHANNEL For testing the Impulse transmission only The reception level will be displayed for 0 2 seconds on the receiver You ll also get an Impulse on the programmed output To check the state of the battery Press TEST BATT The Battery level will be displayed with the 4 LED s for 2 seconds LED control panel which shows the programmed TEAM or CHANNEL Also shows the transmitted Impulse Shows the transmission mode IMPULSE or DATA Charging status Leds The red led indicates that the battery is charging The charge is completed as soon as the green LED in on w TAGHeuer Timin Page 3 8 1 2 The Receiver 1 IMPULSE 2 DATA 3 POWER 4 SET 5 TEAM 6 LED 7 LED 8 LED 9 BUZZER 10 TEST BATT Output for timing Impulse Start gate photocell working closing contact Respect the polarities Female Sub D 9 RS232 Output To
3. C and below 86 F 30 C The red LED lights during the charging process when fully charged the red LED shuts down and the green LED will light on For a fully charged Battery it may take approx 5 hours for a completely discharged battery WARNING Never connect the terminals of the battery in short circuit To avoid keeping the battery pack fully loaded or completely discharged for a long period which reduces the lifespan of the battery In the case of prolonged non utilization of the battery pack it is necessary keep the system in a dry room after a normal discharge In case of a reduced capacity of the battery pack even after the load leave the system ON a whole night to obtain a complete discharge then recharge the battery pack completely Renew the battery pack if the problem continues 3 Software Update With the Firmware already used with the Chronoprinter 545 and the Minitimer HL440 able you to change the transmission mode and Update your device New firware for the HL 675 are available free of charge on our website www tagheuer timing com For this application you need e The RS232 cable HL605 10 e A computer fitted with a D Sub9 RS232 Output e The software FirmwareManager exe How to proceed 1 With the radio switched OFF connect the external power Connect the RS232 between your computer and the HL 675 2 Run FirmwareManager exe TAGHeuer Timin Page 5 8 Select the correct COM Po
4. current 800mA minimum 5 hours Charger HL540 10 o Primary 230V 50Hz 125mA o Secondary 12V 1250 mA Warranty One year after delivery of your purchase The warranty is null and void under the following conditions if the battery is out of order TAGHeuer Timin Page 6 8 Poor maintenance and obvious physical damage Input or Outputs damaged by poor connection If the device was opened without factory authorization THE INSTALLATION INCLUDES 1 Plastic case which can store up to 5 Devices 1 to 4 Transmitters 1 Receiver 2 to 5 antennas 1 Charger 100 240 VAC 9VDC 1 User manual 1 Velcro strap per transmitter 5 Special pinout for Displays HL980 and HL960 990 12345 54321 HL 675 Jelli rou ZER To Display HL 980 6 Special Pinout for TX activating Our radios are equipped with a PNP Transistor on their output This is an IT Standard which also allows us to ensure good autonomy Some devices only work with an RX pin and Ground In order to activate this transistor and initiate the external data from the radio you need to energise the Transistor with an external power supply or a charged condenser 12345 54321 HL675 lee oe To Display HL 960 980 ETSY 9876 7 Pinout Transmitter male socket Receiver female socket 1 NC 1 RS485 Signal A 2 Radio RxD RS232 2 Radio TxD RS232 3 Radio TxD RS232 3 Radio RxD RS232 4 RS485 Signal B 4NC 5 GND 5 GND 6 NC 6 NC 7 RS
5. 485 Signal A 7NC 8 NC 8 NC 9 NC 9 RS485 SIGNAL B TAGHeuer Timin Page 7 8 TAGHeuer PROFESSIONAL TIMING TAG Heuer PROFESSIONAL TIMING 6A Louis Joseph Chevrolet 2300 la Chaux de Fonds Switzerland Tel 032 919 8000 Fax 032 919 9026 E mail info tagheuer timing com Http www tagheuer timing com w TAG Heuer Timing Page 8 8
6. rt Browse and select the correct file Rx Tx Push START on the screen Turn on the HL 675 hold down for 5 seconds ON The HL 675 will enter in a special setup mode Until the file downloaded then validate with OK GE a N Hands on Reinitialize your devices If the systems are in a unknown mode you can Initialise your system in the OEM configuration Channel 1 Team A Buzzer On Baud Speed 9600bps Mode Impulse Push simultaneously SET and TEST BATT for 3 seconds All LED s will flash and the system will beep until it is reinitialized 4 Technical Specification General o Impulse response precision 1 10 000 sec o Transmitting delay 200ms o Frequency 869 MHz REC 70 03 o Power 500 mW o Autonomy at 68 F 20 C 24 hours 1 Impulse per min 8 hours THbC data transm 1 data string each 4 sec o Impedance 50 Ohms o Antenna 1 4 Wavelength 2 5dBi o Impulse Input Short Circuit Working contact Respect the polarity o Impulse Output 4 separated outputs Isolated by an opto coupler Manages up to 4 simultaneous inputs o Channel 4 different channels 1 2 3 4 o TEAM function 4 different codings A B C D o Normal use temperature between 4 F 20 C and 131 F 55 C o Charging temperature between 32 F 0 C and 86 F 30 C o Size without antenna 152 x 108 x 34mm o Weight 470g radio o Power supply 12 V DC 800 mA min Lithium Polymer Battery o Type 12V Li Pol 2000mAh o Charging
7. switch on the receiver press for 3 seconds on POWER The green LED is on To switch off the receiver hold down SET and press POWER To program the TEAM A B C D and to switch off the receiver Hold down SET during the changes To check the programmed TEAM The green LED corresponding to the code A B C or Dis on To change the code hold down SET and press TEAM LED control panel which shows the programmed TEAM or CHANNEL Also shows the Received Impulse Shows the transmission mode IMPULSE or DATA LED control panel which shows the Receiving Level and or possible interferences created by other radio signals To enable or disable the Buzzer To check the Battery status The Level will be displayed with the 4 LED s for 4 seconds 4LED s on 80 100 3LED s on 60 80 2LED s on 40 60 1LEDon 20 40 1LEDon 0 20 power remaining w TAGHeuer Timin Page 4 8 2 Battery Charging Each device has a Lithium Polymer battery with supply 2100 mAh Those batteries may be charged with our charger HL540 10 or other 12V charger with a minimum of 800 mA For charging the battery we advise you to use our OEM TAG Heuer charger Using another model may cause some trouble or harm the device For charging turn off the system Connect the charger on the mains Plug the charger into the device The red LED will be on during the charge IMPORTANT Always charge the devices by temperature above 32 F 0
Download Pdf Manuals
Related Search