Home

User Manual - Snap-on

1. P To change Snapshot settings 1 From the Vantage PRO main menu select Utilities gt Tool Setup gt Save Data The Save Data dialog box displays Figure 5 28 Save Data 40 Figure 5 28 Sample Save Data dialog box Select the After Trigger to open the dropdown menu Select a After Trigger setting Select My Data to open the dropdown menu Select a location to save the data to Select File Type to open the dropdown menu Select a file type Press N X to close the dialog box E YY 5 5 7 Resetting Gauges The Reset button Figure 5 29 returns the recorded digital gauge min max values to zero Figure 5 29 Sample Reset button Use the Reset button to do the following e Track the variation in a component or circuit under a certain condition If the condition changes Reset lets you start tracking again to see the change e Verify a connection problem you found has been fixed by looking for a dropout or a spike in the min max values P To reset the min max digital values e Select Reset A confirmation message displays Figure 5 30 Figure 5 30 Sample Reset confirmation message 42 Component Test Operations Performing Tests When the reset is complete the confirmation message disappears 5 5 8 Saving Data The Save button lets you store data and presets in memory For more information on presets see Using Presets on page 74 P To save data 1 Select Save A dropdown menu displays
2. UE FOL ZETEC CON Figure 5 10 Sample Component Tests screen 5 4 Connecting to a Test Vehicle Certain component tests require the use of specific leads that connect your Vantage PRO M unit to a test vehicle The initial test screen displays connection information P To connect to a test vehicle e Follow the on screen connection instructions located in the Test Procedure and Support windows Figure 5 11 AMA ees SIGHATURE TEST X Conmact test leads TEW HARNESS SIDE Vallow 1AC signal DA CKPROBING Black known good ground IDLE AIR CONTROL VALVE COMMECTOR 10 i fbr l IA VALVE JOMITIGH A T FOCUS 2 0L 2ETEC 0156P BM Figure 5 11 Sample connection instructions 5 5 Performing Tests When you have connected the Vantage PRO unit to the test vehicle you can proceed with component tests 35 Component Test Operations Performing Tests P To perform component tests 1 Select the Test Procedure window 2 Use the Thumb Pad to read all setup instructions Instructions display in the Text Procedure window accompanied by illustrations in the Support window Figure 5 12 check waveform signature legrity Figure 5 12 Sample setup instructions 3 Press the down d arrow to advance to the next panel of instruction as needed 4 Follow the on screen procedures as needed 5 View and verify the test results as explained on screen Figure 5 13 ab Scope thould be uted to a heck waveform signa
3. 5 3 Selecting a Component Test Once a test vehicle is identified you can select from the Component Tests menu The main body Figure 5 10 of the test screen can contain the following sections e Test Procedure window contains connection and testing procedures e Support window contains support information such as connector illustrations e Test Meter window functions as a Graphing Meter Digital Meter or Lab Scope depending on the selected test P To select a component test 1 Select Component Tests gt Component Tests The Component Tests menu displays the available components for the identified test vehicle Figure 5 7 7 CHT SENSOR CKP SENSOR CMP SENSOR CONTROL MOD LOCATION DLC CONNECTOR ECM CONNECTOR PINOUT EEGR ELECTRIC EGR SYSTEM EVAP SYSTEM FUEL PRESSURE FUEL PUMP Figure 5 7 Sample Component Tests menu 2 Select a component The component menu displays Figure 5 8 CHT SENSOR sa COMPONENT INFORMATION TESTS DUALRANGE CHT Figure 5 8 Sample component menu 3 Select TESTS A Tests menu displays Figure 5 9 RESISTANCE TEST SIGNATURE TEST Figure 5 9 Sample TESTS menu 4 Select a test The Test screen displays Figure 5 10 34 Component Test Operations Connecting to a Test Vehicle A e SIGHATLRE TEST CORRECTOR Cormact tet leads VIEW HARNESS SIDE Yalow LAc signal BACKPROEING Black known good ground IDLE AIR CONTROL VALVE i 9 A
4. Figure 5 31 Figure 5 31 Sample Scope Save menu 2 Select an option from the menu Save Movie saves all data in the buffer Save Frame saves only the visible screen data Save Preset saves only Scope screen configurations used for future testing See Using Presets on page 74 for more details Save Image saves the visible screen as a graphic image The Setup Saved Data Notation dialog box displays for screen saving Figure 5 32 Setup Saved Data Notation AGO Save Note venr Make Component Condition jp fea MAP Sensor uninown Figure 5 32 Sample Setup Saved Data Notation dialog box 3 Select from the menus to set preferences as necessary The Setup Saved Data Notation dialog box works the same as the Edit Saved Data Notation dialog box found in the Saved Data mode See Editing Saved Files on page 82 for details 4 When you are finished setting preferences select the Save icon A confirmation message displays with saved data retrieval instructions Figure 5 33 43 Component Test Operations Performing Tests 4 Data saved Select Data Management to view j Prass Wto continue gt Figure 5 33 Sample Data saved confirmation message 5 Press Y a to close the confirmation message 5 5 9 Printing The Print button lets you print the displayed screen P To print 1 Select Print A dropdown menu displays Figure 5 34 OL VOLTAGE TEST CONNEC
5. card into the slot 1 1 5 Procedures An arrow icon indicates a procedure Example P To change screen views 1 Select the View button The dropdown menu displays 2 Select an option from the menu The screen layout changes to the format you selected Using This Manual Tool Help 1 2 Tool Help Your Vantage PRO unit Tool Help contains reference and procedural information found in this manual From the main menu access Tool Help on the Utilities menu See Tool Help on page 93 for details Introduction The Vantage PRO unit Figure 2 1 combines a digital and graphing multimeter lab scope and ignition scope with a powerful diagnostic database Wim Figure 2 1 Vantage PRO This diagnostic database gives you component specific test information and automatically configures the tool for any selected test A multi window format lets you simultaneously view instrumentation readings and component specific test help information 2 1 Functional Description Afe naar e LIRA TINA Figure 2 2 Vantage PRO unit front view 1 Transflective screen 2 N X No and Y a Yes buttons 3 Thumb Pad Introduction Functional Description 4 Right handgrip 5 Brightness Contrast button 6 S button 7 Power button 8 Left handgrip 1 2 3 4 5 6 7 8 9 Figure 2 3 Vantage PRO unit top view 1 CompactFlash CF Card Slot 1 Master program CF
6. e Test Tips gives on screen instructions for performing specific component tests along with drawings and tips Power User Tests select Power User Tests to use pre configured control systems tests The tests are available with or without on screen help 60 Multimeter Operations This section explains the Multimeter menu and operations Multimeter T Graphing Meter Digital Meter Figure 6 1 Sample Multimeter menu The Multimeter menu Figure 6 1 offers the following options e Graphing Meter e Digital Meter The following is an outline of basic Multimeter software operation 1 Select Multimeter software Select the type of Multimeter software and a test configuration for the selected tool See Selecting Multimeter Software on page 62 2 Connect test leads Connect appropriate leads and clips to the Vantage PRO unit See Connecting Leads and Clips on page 21 3 Connect the Vantage PRO unit to the vehicle Procedures will vary 4 Perform the test Set up test and evaluate test results See Performing Multimeter Tests on page 65 Select Multimeter Software Connect Test Leads Connect to the Vehicle Perform the Test Figure 6 2 Basic Multimeter operations 61 Multimeter Operations Selecting Multimeter Software 6 1 Selecting Multimeter Software There are two types of Multimeter tools available e Graphing Meter See Graphing Meter on page 62 e Digital M
7. on page 38 e See Using Cursors on page 39 e See Taking Snapshots on page 40 e See Resetting Gauges on page 42 e See Saving Data on page 43 e See Printing on page 44 e See Using Setup on page 44 e See Calibration LED on page 50 e See Adjusting Channel Settings on page 50 e See Setting the Sweep Time on page 54 e See Setting the Trigger on page 55 65 Scope Operations This section explains the Scope menu and operations NOTE Most of the Scope toolbars and controls work the same as the Multimeter Only the differences are covered in this section L _ Scope Lab Scope Ignition Scope Presets Figure 7 1 Scope selection from main menu The Scope menu offers the following options Figure 7 1 e Lab Scope e Ignition Scope e Presets The following is an outline of basic Scope software operation 1 Select Scope Software Select the type of Scope software and a test configuration for the selected tool See Selecting Scope Software on page 67 Connect test leads Connect appropriate leads and clips to the Vantage PRO unit See Connecting Leads and Clips on page 21 Connect the Vantage PRO unit to the vehicle Procedures will vary Perform the test Set up test and evaluate test results See Performing Scope Tests on page 73 66 Scope Operations Selecting Scope Software Select Scope Software Connec
8. 10 AC DC power adapter 13 adding notes See editing data adjustment 71 alligator clips 16 amps 7 8 connecting 5 A Z Index 59 back up saved files 85 backlight 88 batteries 7 battery pack about 14 charger 14 charging 17 disposing of 97 extending the life of 18 installing 18 low battery warning 19 not charging 99 power status 27 replacing 97 time to charge 18 using 17 18 working when battery is low 19 brightness contrast 5 20 C cables 15 16 channel 1 15 channel 2 16 connecting 21 capabilities scope 8 test instrument 8 channel control bar 50 channel number 51 color theme setting 92 comonent test operations 31 59 CompactFlash cards slot technical specs 7 component tests 31 59 a z index 59 connecting to a vehicle 35 features and benefits 60 how to 60 identify test vehicle 32 new vehicle ID 32 performing tests 35 57 power user tests 60 previous vehicles 33 selecting a test 34 view component information 57 59 control buttons 11 12 brightness contrast 12 N button 11 power 12 S button 12 Thumb Pad 12 Y button 11 cursors 39 DB9F connector 5 DC power jack 5 DC voltage 10 deleting data 77 83 diode 5 8 display 7 display as 45 87 display trigger 55 57 disposal requirements 98 duty cycle 9 DVOM and digital meter 63 E easy scroll 29 94 edit 80 editing data 82 emergency restart 99 F Features and Benefits 60 fil
9. 2 is selected a plus sign colored according to the channel it represents displays in the graph area Figure 5 58 Ifthe Cyl trigger is selected a white plus sign displays along the bottom of the graph area which represents the point in time a cylinder is detected on the RPM lead Figure 5 59 Wailing For Trigger Figure 5 58 Sample Trigger Position marker 56 Component Test Operations Viewing Component Information i 1 j i F I rn Li i EE ea IAAF Ck AMP OA 10 ms al Figure 5 59 Sample Cy Trigger Position marker 4 When you are finished setting the trigger modes press N X to close the menu Trigger Slope The Trigger Slope button Figure 5 60 selects the direction the waveform must be going rising or falling when crossing the trigger point NOTE O This button is only available when a Channel is the active trigger type 5 5 16 Trigger Position The Trigger Position Figure 5 61 button is used for moving the trigger point for a specified channel either along the X horizontal or Y vertical axis of the display 1 m a a acts rar n IL L cl JE Figure 5 61 Sample Trigger Position button P To move the trigger point 1 Select Trigger Position The trigger point marker becomes active 2 Use the Thumb Pad to move the on screen marker and select a new trigger point 3 When you are finished press N X 5 6 Viewing Component Information T
10. AC DC power adapter 3 1 2 Connecting the AC DC Power Adapter The AC DC power adapter Figure 2 7 on page 13 provides power from a wall socket and is required to charge your battery pack Figure 3 4 Sample AC DC power supply connected 1 2 5 mm plug P To connect the AC DC power adapter 1 Plug the 2 5 mm end of the AC DC power adapter into the DC power jack on the top of your Vantage PRO unit Figure 2 3 on page 5 2 Plug the other end into an appropriate wall socket 3 Press the Power button After the start up sequence is complete the main menu screen displays 3 1 3 Connecting Vehicle Auxiliary Power Cables Optional vehicle auxiliary power cables can be used to provide power from the vehicle to your Vantage PRO unit For related information see Vehicle Auxiliary Power Cables Optional on page 14 19 Getting Started Powering On the Unit P To connect the vehicle auxiliary power cables 3 2 3 3 1 Plug the 2 5 mm end of the Lighter Power Cable into the DC power jack on top of the Vantage PRO M unit 2 Plug the other end of the Lighter Power Cable into either the cigarette lighter or the Battery Power Cable receiver 3 Ifthe Battery Power Cable is used clip the other ends of the Battery Power Cable to the positive and negative battery terminals of your test vehicle Powering On the Unit When a master storage CF card is installed in slot 1 and power is supplied you can power on th
11. Average Volts AC rms Ohms Diode Continuity Amps Internal Low Amps 20 Low Amps 40 Figure 6 5 Sample Digital Meter menu Table 6 2 Description of Digital Meter test options Volts DC Measures direct current voltage Measures direct current and uses a filter to remove excess Volts DC Average noise hash on the signal Measures the effective voltage rather than the Peak or Volts AC rms Average voltage Measures electrical resistance Diode Continuity Measures voltage drop across a diode or continuity Amps Internal Measures current for component and parasitic draws under p 10A when connected in series with the circuit being tested Measures current from components like ignition coils Low Amps 20 injectors fuel pumps and parasitic draw using the Snap on Low Amp Probe Low Amps 40 Measures current from components like fans and electric p motors using the Snap on Low Amp Probe Figure 6 6 Sample Digital Meter test screen 64 Multimeter Operations Performing Multimeter Tests 6 2 Performing Multimeter Tests When performing tests with the Multimeter the toolbars and controls work the same as those in Component Tests Button and menu option availability vary depending on your test selection For related information see the following Component Tests Operations sections e See Changing Views on page 36 e See Pausing Data on page 37 e See Reviewing Data on page 38 e See Using Zoom
12. DC Power Adapter on page 19 2 6 3 USB Port The USB port can be used for connecting to a printer keyboard or a PC For related information see the following sections e Setting Up to Print on page 22 e Editing Saved Files on page 82 2 7 Power Sources Your Vantage PRO M unit can receive power from the following sources e AC DC power adapter e Battery pack rechargeable e Vehicle power adapters optional 2 7 1 AC DC Power Adapter The Vantage PRO unit can be powered from a wall socket using the AC DC power adapter Figure 2 7 When both the AC DC power adapter and the battery pack are installed the AC DC power adapter is the primary power source Figure 2 7 AC DC power adapter NOTE O When connected to the Vantage PRO unit the AC DC power adapter will not charge an installed battery pack See Battery Charger on page 14 for details 13 Power Sources Introduction 2 7 2 Battery Pack The Vantage PRO unit can be powered by a rechargeable nickel metal hydride battery pack installed at the bottom of the unit behind the right handgrip Figure 2 8 f pa p gt Figure 2 8 Battery pack installation location 2 3 Battery Charger The battery pack is recharged by an external battery charger Figure 2 9 gt AL A A ri Pr A LL a A Figure 2 9 Baton charger The Vantage PRO battery charger uses the same AC DC power supply that ca
13. Files The Load button lets you view saved test data and do the following e Modify the data view using the Zoom Setup Channel Number Signal Zero Offset and Cursors buttons e Review data using the Review button if the saved data contains more than one screen e Print the screen 81 Data Management Editing Saved Files P To load data 1 From the main menu select Saved Data gt Data Management The Data Management screen displays Figure 8 2 on page 80 2 When selecting a file from the list on screen use the up b and down d arrows 3 When selecting Load from the upper toolbar use the right c and left e arrows P To exit the loaded screen 1 Press N X to return to the Data Management screen 2 Press N X again to return to the main menu 8 3 Editing Saved Files The Edit button lets you add notes to saved test data You can also provide Year Make Component and Condition details P To edit a saved file 1 Plug in a USB keyboard not supplied 2 From the main menu select Saved Data gt Data Management The Data Management screen displays Figure 8 2 on page 80 3 When selecting a file from the list on screen use the up b and down d arrows 4 When selecting Edit from the upper toolbar use the right c and left e arrows The Edit Saved Data Notation dialog box displays Figure 8 3 Edit Saved Data Notation Add Save Note Year Make Component Condition E feos Ehrysias iarstion Secondary E Figu
14. USB Ao A A o O teantl oiante tek cae ole er ae aed acta Cae ac eesti erates 13 POWOh SOUNCCS duda da dada cias 13 ACIDO POWETAJADIET die 13 Battery A owe Ae e daat 14 Battery Chate ciran aa in 14 Vehicle Auxiliary Power Cables Opti0NAl cooocnncnnccccccnnnnnncnononcnnonononnccnnnnonnanonnnononanenss 14 Ledas and IS ad 15 Ghannel T Lea ceren e dades 15 Channel 2 Led dd A wl eg ea 16 AUT AO PUSO iones reo iccanocs 16 Chapter 3 Getting Starte diu ii 17 SUDDIVING POWE oi e So 17 Using the Battery PackKussiionn al da 17 Connecting the AC DC Power Adapter ccccconccncccccncnccconcconccnoncnconnncnnnnnnancnnonnnnnnnnnnancnnnnanenns 19 vi Table of Contents Connecting Vehicle Auxiliary Power Cables ccccoooncccccccnnncocnoncncnnonanononnononononanonononaronnnnnns 19 POWERING Onis Un ta o a a a a ceanseaccesd de a 20 Adjusting Brightness and COTA Geet eae ce A eh A AAA 20 Connecting Leads and Cia cansion seee 21 SENNO UDITO A e ee ee 22 Connecting to a Computers dai 22 Powe OSI e al daa oe 22 Chapter 4s Navi ation scisscecsccsesccecsencew sreteacesvevcosecssececnecdavetvaaveccasaesideosiesteetecesastevuacetountseceoctnss 24 SCONES La Vols R ae at eee ees 24 Ubper TOO Detalladas 24 MR A R giana 26 COMETA Di a o o ee 26 US ea Ee aa 27 Making ESI c101 110 ALSE 27 Navigating Multi Window Screens nia Gietedadee da veea Suan ears elses eee 28 E ISVO CTO MAA PRA E Saunton a EA E 29 Screen Messages srta TU 30
15. all of the firing peaks consistently and calculates the Digital kV measurement correctly Figure D 4 111 Using Sensitivity Adjustment When To Use Sensitivity Adjustment 69 23 Pe 66 Re 3 4 Figure D 4 Sample of properly set sensitivity for Multiple Spark systems Sensitivity Set Too Low When other events are detected as cylinder firings the detection sensitivity may be set too low The setting should be increased until the ignition scope consistently detects each cylinder firing Figure D 5 illustrates the detection sensitivity level set at 500V which is too low because the start of Dwell is being displayed as the firing of cylinders 3 and 2 88 nee ees te 8 8 a A j z GAP E et ith kv i a Par 4 ma jee hil Yi Figure D 5 Sample of sensitivity adjustment set too low Figure D 6 illustrates the start of Dwell being detected as a cylinder firing on the secondary waveform because the sensitivity adjustment is set too low 112 Using Sensitivity Adjustment Some Common Ignition Problems Figure D 6 Sample of sensitivity adjustment set too low D 2 Some Common Ignition Problems This section explains how to set the sensitivity level properly when you encounter some common ignition system problems D 2 1 Example Vehicle With A Shorted Spark Plug Figure D 7 illustrates inaccurate cylinder firing detection on a vehicle with a carbon fouled spark plug The spark plug on cylinder 3 was severely
16. and connect lead to cylinder A rpm Figure 5 40 Sample Ignition System dialog box The following ignition types and settings are available e Standard The Inductive RPM Pickup connects to the coil or plug wire on a distributor system Set the number of cylinders and cylinder firing order Figure 5 40 on page 47 e Waste Spark The Inductive RPM Pickup connects to a plug wire on a waste spark distributorless system Set the number of cylinders cylinder firing order and polarity IMPORTANT Be sure the firing order and cylinder firing polarity values are correctly set up before using the Ignition Scope to test Waste Spark systems e Direct The Inductive RPM Pickup connects to a plug wire if applicable on a direct ignition system Set the number of cylinders and cylinder firing order e Other The Inductive RPM Pickup connects to a plug or a coil wire Set the RPM factor appropriate for the test vehicle NOTE The Ignition System dialog box can also be accessed from the Utilities Tool Setup menu Refer to Ignition System on page 88 for details To change Ignition System settings 1 Select Setup gt Ignition System The Ignition System dialog box displays Figure 5 40 2 Select the Ignition System values as needed 3 Press N X to close the dialog box Grid Select Grid to display the background grid pattern on all graphing test screens 47 Component Test Operations Performing Tests P To
17. be viewing and copying or moving presets from When selecting a file from the list on screen use the up b and down d arrows When selecting Copy or Move from the upper toolbar use the right c and left e arrows A confirmation message displays Press Y a to close the dialog box You return to the Preset Management screen P To verify the preset copied or moved 1 2 Leave the CF2 card installed From the upper toolbar select Setup The Save Data dialog box displays 78 Scope Operations Using Presets 3 Select the destination storage memory preference from the Save To options and then press N X to close the dialog box When the Preset Management screen displays you should see the preset s that you copied or moved from your source storage memory 7 3 5 Selecting Multiple Presets The Select All button highlights all the presets so you can delete copy or move all of the files simultaneously 79 Data Management This section explains the Saved Data menu and Data Management operations The Saved Data button Figure 8 1 accesses the Data Management screen Figure 8 1 Sample Saved Data button menu The Data Management screen Figure 8 2 lets you manage storage memory and saved files NOTE O Factory installed files identified by a lock icon cannot be edited deleted copied or moved igrillon Secondary igratron Secondary laT Sensor injectors MAP Sensor LMP Sensor Fuel Pump Figure 8 2 Sampl
18. carbon fouled In the illustration the detection sensitivity level is set too high and the cylinder is not being detected consistently A 2 30kV 3 2 AZ AAA A rr MA aa Figure D 7 Sample sensitivity set too high Decreasing the detection sensitivity to 1 5 kV as illustrated in Figure D 8 resulted in the consistent detection of the shorted cylinder 113 Using Sensitivity Adjustment Some Common Ignition Problems 471 2 ee z a pi a Fer o maiean Pi Figure D 8 Sample shorted spark plug detected D 2 2 Example Vehicle With A Coil Not Firing Figure D 9 illustrates accurate cylinder firing detection on a vehicle with the 6 3 coil not firing Lowering the detection sensitivity does not help because there are no firings from the 6 3 coil SEA i afi aft o AP l 1 A et Par ma Figure D 9 Sample 6 3 coil not firing and not detected The actual cylinder spacing can be seen by changing to the 200 ms fixed time sweep and viewing the raw waveform on channels 1 and 2 The cylinder spacing long short long short verifies a coil is not firing Figure D 10 114 Using Sensitivity Adjustment Some Common Ignition Problems Am E r ii LES Pia me 2 1 A ee A a Figure D 10 Sample raw waveform of coil not firing 115 Numerics 10 Minute Electronic Class 60 15 Minute Ignition Class 60 A AC power adapter technical specifications 7 AC voltage
19. card slot no hot swapping 2 CF Card Slot 2 Supports I O hot swapping 3 USB ports Protected by sliding shield For printer keyboard mouse or PC computer 4 Channel 1 CH1 yellow V Q Diode Hz PW F INJ PW Duty Cycle 200V max 5 Common ground COM black 6 Channel 2 CH2 green VDC 200V max 7 Amps 10A blue 32VDC max 8 Aux Port DB9F connectors such as the split lead adapter or the inductive rom pickup 9 DC power jack Figure 2 4 Vantage PRO unit back view 1 Stand 2 Casing hooks Introduction The Stand 2 2 The Stand The Vantage PRO unit has a built in metal stand attached to the back When the stand is not in use it is secured to the back of the unit by integrated casing hooks When extended the stand allows the unit to rest at a 45 angle for hands free viewing Figure 2 5 Figure 2 5 Vantage PRO unit with stand extended The stand can also be extended to a hanging position by pressing the left side towards the right and rotating forward Figure 2 6 Figure 2 6 Vantage PRO unit with stand in hanging position Introduction Technical Specifications 2 3 Technical Specifications Display Transflective Liquid Crystal Display LCD Visible under any lighting condition 320 x 240 resolution 1 4 VGA 256 colors 5 7 inches 144 8 mm CompactFlash CF Card Slot CF Type 1 Slot 1 is for the master program CF card Slot 2 is for use
20. for the specified channel it 99 can be moved up down left or right Calibration LED Indicates channel calibration SNS Lets you adjust the ignition scope sensitivit Adjustment y 9 p y P To navigate toolbars e Press the left e and right c arrows to move between buttons e Press the up b and down d arrows or press the N X button to move between the upper and lower toolbars When Easy Scroll is active press the N X button to move to the upper toolbar Refer to Easy Scroll on page 94 for more information 4 1 4 Status Bar The status bar Figure 4 1 on page 24 is located at the bottom of the screen This non selectable display area contains the test vehicle identification battery power status and time 4 2 Making Selections Use the following instructions to navigate the interface and make selections For related information see To navigate toolbars on page 27 P To make selections 1 Highlight a button menu option or window 2 Press Y a to select P To navigate the main body of a screen e Press the Thumb Pad arrows P To exit a selection e Press N X 27 Navigation Making Selections 4 2 1 Navigating Multi Window Screens The main body of the screens for both Component Tests and Component Information are divided into multiple windows Figure 4 7 NOTE Scroll arrows within a window indicate additional information is available that cannot fit on the screen See To view additional
21. in the following ways e Add notes e Change filename NOTE A USB keyboard not supplied is required to edit presets P To edit a preset 1 From the main menu select Scope gt Presets The Preset Management screen displays Figure 7 14 on page 74 2 Plug in your USB keyboard 3 Highlight a preset from the list Select the Edit button The Edit Preset Name And Note dialog box displays Figure 7 17 Edit Preset Name And Note Additional iio malon ESC to finish Figure 7 17 Sample Edit Preset Name And Note dialog box NOTE O The Notes and Name icons are not active if a keyboard is not plugged in 5 Select Notes The Additional Information section activates Figure 7 18 76 Scope Operations Using Presets Edit Preset Name And Note Figure 7 18 Sample Note selection Using your keyboard type a text note 7 lines maximum then press Esc to exit the Additional Information section 7 Select Name The File Name field is now active Figure 7 19 Edit Preset Name And Note cave ate hist Fila Hama 2 A Enter a file name here Additional information ESC to finish Figure 7 19 Sample Name selection 8 Using your keyboard type a file name then press Esc to exit the File Name field NOTE If you do not provide a file name a name is automatically created for you User00x for example 9 Select Save After processing your edits you return to the Preset Management scree
22. information on page 29 for additional information H Sereg SECONDARY TESTSII Wardage PRO can be uted to view secondary igrition wawehornms Figure 4 7 Sample Component Tests screen 1 Test Procedure window 2 Support window 3 Test Meter window P To select a window 1 Use the down d arrow to move from the upper toolbar 2 Select a main body window When selected the background and title text of the window change colors Figure 4 8 Current flow through each njector should be about the Tires P To deselect a window e Press N X When deselected the background and title text of the deselected window change colors 28 Navigation Easy Scroll P To view additional information Press the up b or down d arrow in the selected window Figure 4 9 to display more information CURRENT RAMP TEST 1 Connect current Probe to ardage PRO ot shower j i E FEE DOS O E n E E F Figure 4 9 Down d arrow indicating more information When optional details or additional tests are available for the selected component test a jump bar displays at the bottom of the Test Procedure window Figure 4 10 gt for Auto Zero hd Figure 4 10 Sample jump bar P To display additional information using the jump bar 1 Press the right c arrow Figure 4 10 2 Follow the on screen instructions in the jump bar to display all available information 3 When you are finished follow the on screen ins
23. manually selected for display NOTE Both channels automatically display in the 2 ch Graphing Meter mode The following channel options are available e Displayed makes a channel s signal visible e Inverted flips the selected waveform upside down This is typically used when testing secondary ignition or displaying waveforms from the Low Amps Probe e Coupling AC subtracts the average value of a waveform to see small variations which is ideal for viewing alternator ripple or fuel pump amps This blocks the DC portions of an input signal to amplify the AC portions without driving them off the center of the screen e Peak Detect captures fast events spikes and glitches for signals going in positive and negative directions e Filter minimizes unwanted noise e Auto Find picks the best scale to fit the selected signal pattern on the screen If run on the same channel as the trigger the trigger level is set halfway between the minimum and maximum values of the waveform NOTE When testing with the Single Cylinder Ignition scope the Channel 1 Peak Detect option cannot be turned off P To display Channel Two 1 Select Channel Number The channel setup menu displays Figure 5 48 ph Peak Detect pry Filter 2 Select Ch 2 gt Displayed The Channel Two trace displays Figure 5 49 51 Component Test Operations Performing Tests Displayed pA Peak Detect pry Filter 3 Press N X to clos
24. selected topic or book text screen Use the up b and down d arrows to view additional text Press the left e arrow to return to the Table of Contents screen Select a book and press Y a to collapse the contents oo p a AO P To exit Tool Help e Press N X twice 9 4 Easy Scroll The Easy Scroll utility functions as a selection shortcut that lets you use only the Thumb Pad arrows to highlight and select an item Refer to Easy Scroll on page 29 for more details P To turn Easy Scroll on and off e Select Utilities gt Easy Scroll Figure 9 11 Tool Setup System Tools Tool Help MENE Connect to PC Run Shop Info System Info Figure 9 15 Easy Scroll turned on A check mark to the left of the Easy Scroll option displays 94 Utilities Connect to PC NOTE Easy Scroll stays on until you manually turn it off 9 5 Connectto PC The Connect to PC selection is used with the optional ShopStream Connect software which lets you view data files on a computer and share files 9 6 Run When specified select Run to load Snap on authorized applications 9 7 Shop Info Select the Shop Info option to enter or view ownership information for the unit P To enter unit identification 1 Select Utilities gt Shop Info The Shop Information dialog box displays Figure 9 16 Shop Information raza semer Road Cay Slade San lose Ca lP Phone o fs dd 1 800 424 7226 Press Fer bom fh
25. the sample rate is slower and the peak firing voltage or the entire firing can be missed if it happens between samples Figure B 3 ERE e Am Figure B 3 Sample 10 ms Sweep Peak Detect off When Peak Detect is on the firings will be displayed regardless of the Sweep because the scope is sampling at the maximum rate The longer the Sweep the more useful Peak Detect can be Figure B 4 illustrates a Firing Peak captured at a 10 ms Sweep rate Compare this illustration with Figure B 3 on page 102 TP e elas 102 Using Peak Detect When To Use Peak Detect B 1 2 Example Testing a TPS for Glitches With a sweep of 5 or 10 seconds typically used for testing a throttle position sensor TPS the sample rate is relatively slow When a sweep is longer the sample rate is slower which increases the chance that a glitch can be missed because it occurred in between samples Figure B 5 illustrates a TPS glitch not captured Figure B 5 Sample Slow Sweep TPS Glitch not captured To increase the chance of capturing a glitch without Peak Detect a shorter sweep is needed Figure B 6 illustrates a TPS Glitch captured using a faster Sweep Figure B 6 Sample Faster Sweep TPS Glitch captured Even if the glitch was captured with a sweep this short the glitch could easily be missed if you looked away for a moment or even blinked When Peak Detect is on the scope is sampling at the maximum rate a signal glitch can be captured usin
26. the screen 32 Component Test Operations Identifying the Test Vehicle Figure 5 4 Sample Vehicle Identification data When you have finished identifying the vehicle a confirmation message displays Figure 5 5 Figure 5 5 Sample Vehicle ID confirmation message 3 To proceed select a component test GQ To exit New Vehicle ID Press N X anytime during the ID process to return to the previous menu Continue pressing N X until you return to the main menu 5 2 2 Previous Vehicles When testing a vehicle that has already been identified the Previous Vehicles menu option provides access to the Load Vehicle Identification screen Figure 5 6 The Vantage PRO unit automatically saves the last ten vehicle identifications and lists them on this screen P To load a previously identified vehicle 1 Select Component Tests gt Previous Vehicles The Load Vehicle Identification screen displays Figure 5 6 Component Test Previous Vehicles Vehicle 10 FORO FUEL INJECTION 2006 FOCUS 20L ZETEC BUICK FUEL INJECTION 2004 LACROSSE SSL VIN 2 MERCEDES BENZ FUEL INJECTION 1354 E320 CADILLAC FUEL INJECTION 2006 CTS 3 6L VIN Figure 5 6 Sample Load Vehicle Identification screen 2 Select a vehicle from the list P To exit the Load Vehicle Identification screen Press N X to return to the main menu and keep the current vehicle identification setting 33 Component Test Operations Selecting a Component Test
27. type states how to avoid the hazard e ltalic type states the possible consequences of not avoiding the hazard An icon when present gives a graphical description of the potential hazard Example Risk of unexpected vehicle movement a e Block drive wheels before performing a test with engine running A moving vehicle can cause injury Important Safety Instructions For a complete list of safety messages refer to the accompanying safety manual SAVE THESE INSTRUCTIONS Table of Contents Sale NTO MA ON ui in iv Table OF COMLCIUS unicidad aaa vi Chapter 1 Using This Manual sscitcnsicnriin is 1 Alo nn A A 1 elo A o gg A O 1 gt RR ee eee ee 1 TENMINOIO IV iia A 2 Notes and Important Messages cccoccccccccnnccconoconococonnnononnnononnnnonannnonnrnnonannnnnannncnnnnnrenaranenos 2 OG A Pe talede ade ese anon mma ia act 2 TOO NSN Pin A 3 Chapter 2 INtoOdUclON sisi rin 4 Functional Descrip a a ico 4 THe StI IA A nn ec bane ee A 6 TEENINICAl SPSCINC ANON S armel aes aceite ace ete caes N basa cease oicauoen es eee 7 Operating SPeCIICALIONS aias e el a cleat al ented ln 7 SCONE Capablanca 8 Test Instrument capable S alot nacio dida 8 SONO BULA Si todo ei ee 11 Wa NES BUON lio ee 11 A E o In a Ee aaae iaa a daia 11 TRUMP Radenne ee eee a E N EN 12 Brghtness Contrast BUOM rarna oi EE EN iN 12 1 A nen EN Ne A etna ee nee 12 PONE o seeescemiee 12 A Ee ae Oe ee eee 12 Testkead JACKS isso lila 12 DE OW GT di do dd 13
28. you set the detection sensitivity to cylinder firings The lower the setting the more sensitive the ignition scope will be to detecting cylinder firing Being able to adjust the sensitivity and improve cylinder detection increases the range of vehicles that can be tested and the range of secondary pickups that can be used AA A 2 00kV Figure 7 9 Sample ignition trigger adjustment To adjust cylinder firing detection sensitivity 1 Select the Sensitivity Adjustment button The button appears depressed and remains highlighted to indicate that the function is on 2 Pressthe up b or down d arrows as needed to move the level indicator on the left of the graph x axis NOTE Unless you are having problems detecting cylinders a sensitivity setting of 2 0 kV is optimal for many ignition systems 3 When you are finished setting the ignition scope sensitivity press N X to deselect the button NOTE With Wasted Spark ignition systems the sensitivity level setting only displays on Channel 1 but the setting applies to both channels See Using Sensitivity Adjustment on page 110 for usage details 71 Scope Operations Selecting Scope Software Missed Cylinder Detection When a cylinder firing is not detected because it is either firing too low to be detected at the current setting or is not firing at all a blank space displays on screen Figure 7 10 Figure 7 10 Sample missing cylinder detection P To verify a missing
29. 40 C If left in the battery charger unit once the proper room temperature is achieved charging will begin The battery pack may be too cold Allow the battery pack to warm to at least 32 F 0 C If left in the battery charger unit once the proper room temperature is achieved charging will begin The battery pack may be dead The battery pack must be replaced See Replacing the Battery Pack on page 97 Use another power source to continue working See Supplying Power on page 17 A 2 Unit Will Not Power On The following conditions will prevent your Vantage PRO unit from powering on No master storage CF card in CF Slot 1 No or discharged battery pack and no auxiliary power connected See Supplying Power on page 17 A 3 Emergency Restart If your Vantage PRO unit Pauses or will not power off you can perform an emergency restart P To perform an emergency restart 1 Remove the left handgrip 2 Locate the emergency restart button in the lower right corner on the back of the unit Figure A 1 99 Troubleshooting Emergency Restart Mos Wyn o WAAL AVAL AAA o k Figure A 1 Emergency restart button location 3 Gently insert a toothpick or some other non metallic item into the emergency reset button hole and depress the button The unit restarts 100 Using Peak Detect Peak Detect is used to capture fast events spikes and glitches for signals going in positive and nega
30. A 1 5 2 digits 0 01 A 1 0 2 digits Continuity 0 0024 1 2 digits 1Accuracy measured at 25 C is shown as of reading Number of least significant digits For example a 100V DC signal accuracy reading would be 0 25 2 digits or 99 75 to 100 25 2 digits or 99 73 to 100 27 Introduction Function Range Resolution Accuracy 1Hz 1500Hz 0 1 1501 Hz 3000Hz vee 1Hz 9kHz 3001 Hz 7500Hz 1 2 digits 0 5 9001Hz 20kHz 750Hz 15kHz 2 2 digits 1 15001 Hz 20kHz 1 5 ma O O Ol O o o 0 01Hz 0 25 2 digits 0 1Hz 50 0 1Hz 00 1000 2000 3Hz 5000 20Hz 100Hz 1 5 2 digits 1800Hz 3 5 2 digits i 7 0 5 2 digits O1 N 1Hz 0 5 2 digits 2000 3000 5000 10000 15000 20000 50000 2 2 lt L N O o ma o 0 00 k Ok 400k fk M 10k 2 0 2 digits Accuracy measured at 25 C is shown as of reading Number of least significant digits 500 oo 2000 5000 2000 2000 gooo 10000 EZA 20000 _ 50000 eo 1 5 2 digits 100 h h O O1 For example a 100V DC signal accuracy reading would be 0 25 2 digits or 99 75 to 100 25 2 digits or 99 73 to 100 27 Operating Specifications Introduction Operating Specifications 0 005 s iM Boat iM Boat 2 digits 0 01s 0 025 05s 0 1 2 digits 0 25s 0 1ms 0 5 s
31. Contado Mess ade in ile 30 Warning Messages anesse as 30 Error Messe Serra a 30 Chapter 5 Component Test Operations oooconcccccnnccnnccnccnncnnncccnonnnnnnnnenonnnnnrrrrennnancrrrrrnannnnnnnnas 31 COMPONENTES a lai A ad ee aut aes 31 Identifying the Test Vehicle avs ori acia 32 New Vehicle Duse a a a a a A a 32 Previous Vehicles asosga a a a a A 33 Sel cting a Component Test 34 COMMECHING Oa TES VEN tae Eo 35 Performing nn A O E PO o A 35 CAIN MEWS sates asset a ld rol 36 PAUSING Data ceo 37 Reviewing ND Maia AAA AA A ta AT 38 USNI ZOOM lacas o coo ld andes 38 USING BT A te tee eer ee ee 39 TAKING SMa DS MOUS uses born diia 40 FUSS CUUNIG GAG CS id A A E 42 Savno Dala O 43 A PPP O nt ieaeninuans 44 A A cums saad 44 A PP ae es ec net a ca eee hahaa tae canes accel d att asa a aces 45 CHDAI teca oi idiota 50 Adjusting Channel SettingS coccoocccnncconccncnnnncononnancnnnononcnnnnnanennnnnnnnnnonnnrnnnnnnnnnnnnanennnnnnns 50 Setting Ihe SWEEP TIM ati 54 Setting the Trigger oooccccccocccnnccocncncoconcnonononnnncnnoncnnnnnnnnnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnanennss 55 Tigger FOSON ura AAA a 57 Viewing Component INfOrMAa ON ss aa a T 57 LASTLY ING the Venice sica e an aulel le aac aug eaaeteauaseaaue dees 58 Viewing Component Information oocccccccccnccccncnnncncnnonnnnnonnnnnononennnnnnnnnnnnnnrnnnonnanennnnnnennnonnns 58 A A eR ne RC ae ee eR Cee ee een eT eee ome 59 vii Tab
32. Do not replace the 10 amp fuse with a higher amp fuse P To replace the fuse 1 Turn the Vantage PRO unit off 2 Using a fuse puller or needle nose pliers carefully grasp the fuse and remove it from the back of the unit 3 Insert the new 10 amp fuse into the fuse slot in the back of unit 10 4 CompactFlash CF Cards Software updates are released on CF card media that inserts into your Vantage PRO unit Refer to the instructions accompanying the CF card for installation procedures Once installed the CF card is linked to your tool and will not operate on any other Vantage PRO unit 10 5 Storage Tips When storing your Vantage PRO unit remember the following e Always turn the Vantage PRO unit off e Keep in mind the storage temperature range e Remove the battery when storage time is extensive 10 6 Disposal Requirements Always dispose of materials according to local regulations 98 Troubleshooting The following are solutions for problems that can occur while using your Vantage PRO unit A 1 Battery Pack Not Charging If the battery pack does not charge The battery pack may not be installed in the battery charger unit properly Make sure the battery charger unit is receiving power and without using force adjust the battery pack installation in the battery charger unit until the red status light displays The battery pack may be too hot Allow the battery pack to cool to at least 104 F
33. MOID POM provider a ground l energue normally closed Purge colercid LOCATION Besi test Location purge Al the EVAP purge colanond cornmecior 2 pir Component Localiory On the nahi de or ha rear of the Engre nes Figure 5 62 Sample Component Information screen P To select a component 1 From the Component Tests menu highlight Component Tests The Component Tests menu displays the available components for the identified test vehicle Figure 5 63 58 Component Test Operations A Z Index AC PRESSURE SENSOR ACCEL PEDAL SENSOR BARO SENSOR CAMSHAFT ACTUATOR CKP SENSOR CMP SENSOR CONTROL MOD LOCATION ECM CONNECTOR PINOUT ECT SENSOR ENG OIL LEVEL TEMP SENSOR Figure 5 63 Sample Component Tests menu 2 Select a component from the menu A component menu displays Figure 5 64 Figure 5 64 Sample component options 3 Select Component Information The Component Information screen displays Figure 5 65 5 7 A Z Index OPERATION CONMECTOR CMP camshal achuators use VIEW HARNESS SIDE Erne of premure lo Control FACKPROGING CONNECTOR lake and exhaust camhah EXHAUST BANK 1 hierro gt LOCATION Best ter Locion Al Ihe componer cormector or a the ECM Comparer Locaion Al lhe Front of the Engra on both of the cylinder heidy Figure 5 65 Sample Component Information screen Select A Z Index to view a list of over 100 meter capabilities and automotive electronic t
34. TOR Figure 5 34 Sample Print menu 2 Select a menu option and press Y a The screen prints according to your printer settings See Setting Up to Print on page 22 5 5 10 Using Setup The Setup button Figure 5 35 lets you change the way information displays z T loriti n System i Grid Trigger Display Scales Display Eh Inverse Colors FS Save Data Figure 5 35 Sample Setup button menu P To use Setup 1 Select the Setup button A dropdown menu displays 2 Select one of the possible options which are explained in the following sections 44 Component Test Operations Performing Tests 5 5 11 Units Select Units to change the units of measurement for vacuum and pressure Figure 5 36 Vacuum Pressure Display As fritig si Factory Defaut Factor Defa Links Division Full Scale Figure 5 36 Sample Units dialog box The Display As dropdown menu sets how the scale units are displayed on the Scale button and inthe Channel Status area Figure 5 37 dl E e Aaa Wal r s 000 iz CAI ls CADILLAC FUEL INJECTION 2006 CTS 3 6L VINT 08 004 oe Figure 5 37 Setup Units Factory Default sample screen 1 Channel Status area Displays the scale settings for all channels 2 Scale button Displays the scale setting for the currently selected channel There are three Display As scale unit options e Factory Default the Channel Status area displays the Units Division for al
35. Vantage PRO eng Raw A ENG1326 1 2006 4 ENG1000 3 2 2006 EN61000 3 3 1995 Vantage PRO EETM303 Diagnostic Platform IEC 61010 1 EN 61010 1 Name C Ferra Position supply Chain Manager Signature Safety Information For your own safety and the safety of others and to prevent damage to the equipment and vehicles upon which it is used it is important that the accompanying mortant Safety Instructions be read and understood by all persons operating or coming into contact with the equipment We suggest you store a copy near the unit in sight of the operator This product is intended for use by properly trained and skilled professional automotive technicians The safety messages presented throughout this manual are reminders to the operator to exercise extreme care when using this test instrument There are many variations in procedures techniques tools and parts for servicing vehicles as well as in the skill of the individual doing the work Because of the vast number of test applications and variations in the products that can be tested with this instrument we cannot possibly anticipate or provide advice or safety messages to cover every situation It is the automotive technician s responsibility to be knowledgeable of the system being tested It is essential to use proper service methods and test procedures It is important to perform tests in an appropriate and acceptable manner that does not endanger your safety the
36. a to adjust the size of each snapshot and the amount of data recorded after a snapshot trigger point Save Data also lets you set the saving and loading location for saved files P To adjust snapshot preferences 1 From the main menu select Utilities gt Tool Setup gt Save Data The Save Data dialog box displays Figure 9 7 Save Data Figure 9 7 Sample Save Data dialog box 2 Select from the drop down lists as necessary The drop down list closes automatically 3 Press N X to close the Save Data dialog box NOTE O The Save Data dialog box can also be accessed from the Setup menu on the Saved Data management screen Refer to Data Management on page 80 for details 89 Utilities Tool Setup 9 1 5 Printer Select Printer to check the printer compatibility status Your Vantage PRO unit supports USB printing to PCL 3 Printer Command Language Level 3 printers Contact the Hewlett Packard Development Company to see if your printer supports the PCL 3 standard See Setting Up to Print on page 22 for more details P To adjust print settings 1 From the main menu select Utilities gt Tool Setup gt Printer The Printer dialog box displays Figure 9 8 Port fuse Figure 9 8 Sample Printer dialog box 2 Select from the drop down lists as necessary The drop down lists close when Y a is pressed 3 Press N X to close the Printer dialog box 9 1 6 Date Select Date to set the date that dis
37. basic screen layout and general Vantage PRO unit navigation 4 1 Screen Layout Vantage PRO screens include an upper toolbar a main body a lower toolbar and a status bar Figure 4 1 Wailing for Trigger Figure 4 1 Sample Scope screen 1 Upper toolbar Contains buttons that control various on screen display and storage functions 2 Main body Displays menus and test data 3 Lower toolbar Contains buttons that control various test functions 4 Status bar Contains the test vehicle identification the battery power status and the time 4 1 1 Upper Toolbar The upper toolbar Figure 4 2 and Figure 4 3 controls vary depending on the module and stage of operations Table 4 1 Figure 4 2 Sample live screen upper toolbar 24 Navigation Screen Layout H DoE a Figure 4 3 Sample paused screen upper toolbar Table 4 1 Upper toolbar controls ETA O OO o Name a ce CO ce Lets you change the way information appears and Setup E where it saves and enter vehicle system information Data Buffer The Data Buffer Figure 4 4 is located just below the upper toolbar buttons and indicates how much test data is stored Figure 4 4 Sample Data Buffer 1 Pause button 2 Data Buffer When the screen is paused the position indicator displays the current frame number and the amount of data on the screen relative to the total data captured Figure 4 5 25 Navigation Sc
38. connnnnnnnnnnnnnonnnnnnnonnnnnnnnnannnnnnnnnnnnnenanos 104 Peak Detect and the Graphing Meter cccccccsseececeseeeeeeeeeeeeeeseeseeeeseeeeeseeeeeesenseeessaaeeeeees 105 Appendix C Using NOISE FIET nicas 106 When t0 USE Flete ne 106 Graphing Meter Filter Use cansas pia 106 SCOPE A 109 Appendix D Using Sensitivity AdjuStMeNt occoonnnccccnnnnncccnnnncononnnancccnnnncnncnnanncnnnnanrnrenannnnnnas 110 When To Use Sensitivity Adjustment ooccccconccnncccccnnncnonnnncnnnnononononcnnononncnnnnnnnnnonnnenonnnnncnnnnnns 110 Improper Sensitivity AQjJUStMENTS ooccccccocccnnccnnncnnoconcnnnonnnnnnnnonncnnnnnnnncnnnnnnrnnnonnnncnnnnnaneneos 110 Some Common lgnition ProbleMS cccccsssseccceeseeccceeeeeeeeeeeceeeeeeceeeeeaeeeeeeeeeeesseseeessseeeensas 113 Example Vehicle With A Shorted Spark Plug ooccccoooccccconcconcnnnnconcnnanoncnonnccnnnnnanancnnnnccnnnnos 113 Example Vehicle With A Coil Not FiriNg oocccccoocconocconnnccconcnnnonnncnncnnoncnnnnnononncnnancnnnnnos 114 gt AA Ag eiacenicueag hives eceai secu et E E A A E T 116 Using This Manual This manual contains instructions for using the Vantage PRO unit Some of the illustrations shown in this manual may contain options that are not included on your system Contact a sales representative for availability 1 1 Conventions The following conventions are used 1 1 1 Bold Text Bold emphasis is used in procedures to highlight selectabl
39. cylinder firing e Lower the sensitivity setting to verify that the cylinder is firing but firing too low to be detected at the current sensitivity setting If a cylinder is not firing at all the blank space on the graph will remain See Using Sensitivity Adjustment on page 110 for more details Digital kV View When using the ignition scope the Digital kV view selection Figure 7 11 displays the digital kV readings corresponding to the selected channel of the ignition scope and provides another way to monitor the secondary ignition system When testing Wasted Spark ignition systems Power firings display on channel one and Wasted Spark firings display on channel two NOTE The digital values will only be as good as the source waveform If there is a problem with the lead connection or set up and a stable waveform is not displayed the digital value may not be calculated correctly If problems are experienced with the digital values check lead connections and Ignition Setup If the measurement cannot be calculated dashes will display in place of digital values Figure 7 11 Sample Digital kV menu selection Firing kV Spark kV and Spark Duration burn measurements are calculated from the secondary waveform e Firing kV FKV voltage required to overcome the rotor and spark plug gaps and establish a spark across the spark plug electrodes 72 Scope Operations Performing Scope Tests e Spark kV SKV voltage required to
40. d 3 Press N X to close the Units dialog box 9 1 2 Ignition System Select Ignition System to choose the appropriate parameters for the vehicle you are testing such as ignition type number of cylinders firing order polarity 1 trigger or rom factor Figure 9 5 lonition System Ignition Type Cyts Firing Order 1 Trigger A Trigger Coir connection is not used to view waverorms is only for display of RPM when the 41 trigger ls connected to he coll wire Figure 9 5 Sample Ignition System dialog box 9 1 3 Power Management Select Power Management Figure 9 6 to control the time before the following occurs e The backlight turns off e The unit goes into standby mode e The unit turns off The following time setting rules apply e The backlight only turns off if its time setting is shorter than the Standby time setting e The unit must be in Standby mode before it can turn off according to the time setting 88 Utilities Tool Setup Power Management stand By Tumo IS Minutes EO Minutes Figure 9 6 Sample Power Management dialog box For related information see Powering Off the Unit on page 22 P To set power management options 1 Select Utilities gt Tool Setup gt Power Management 2 Select settings from the dropdown menus The drop down lists close when Y a is pressed 3 Press N X to confirm your selection and close the Power Management dialog box 9 1 4 Save Data Select Save Dat
41. d operations The Utilities button accesses system information and various system controls Figure 9 1 Tool Setup System Tools Tool Help Easy Scroll Connect to PC Hum Shop Info System Info Figure 9 1 Sample Utilities menu The following utilities options may be available e Tool Setup e System Tools e Tool Help e Easy Scroll e Connect to PC e Run e Shop Info e System Info NOTE some of these utilities are also accessible from the module you are using in the upper toolbar Setup menu Tool Setup The Tool Setup menu Figure 9 2 lets you adjust settings for optimum performance 86 Utilities Tool Setup ignition System Power Management Save Data Printer Date Time 5 Button Color Theme Figure 9 2 Tool Setup sample menu The Tool Setup submenu may include e Units e Ignition System e Power Management e Save Data e Printer e Date e Time e S Button e Color Theme 9 1 1 Units Select Units Figure 9 3 to change the displayed units of measurement Figure 9 3 Sample Units dialog box Display As sets how the scale units are displayed Figure 9 4 87 Utilities Tool Setup Figure 9 4 Display As menu sample P To change the units of measurement 1 From the main menu select Utilities gt Tool Setup gt Units The Units dialog box displays Figure 9 4 2 Select options from the drop down lists as necessary The drop down lists close when Y a is presse
42. e Vantage PRO unit For related information see e Supplying Power on page 17 e Powering Off the Unit on page 22 e Unit Will Not Power On on page 99 To power on the Vantage PRO unit e Press and hold the Power button Figure 2 2 on page 4 until the unit beeps After a few seconds the main menu screen displays Adjusting Brightness and Contrast The Brightness Contrast button Figure 2 2 on page 4 on the front of the unit adjusts the screen for optimum viewing Figure 3 5 Set Brightness Contrast dialog box 1 Brightness slide control 2 Contrast slide control 20 Getting Started Connecting Leads and Clips P To adjust brightness and contrast 1 Press the Brightness Contrast button The Set Brightness Contrast dialog box displays Figure 3 5 Select a slide control using the right c or left e arrows Press the up b or down d arrows to adjust brightness and contrast Press N X to close the dialog box 3 4 Connecting Leads and Clips The Vantage PRO unit uses standard safety banana jacks The following section explains how to connect the provided Vantage PRO unit leads and clips as needed NOTE If you need to extend the length of a lead using a jumper wire keep it as short as possible P To connect the Channel 1 lead 1 On the top of the Vantage PRO unit plug the right angled black ground plug into the jack labeled COM 2 Plug the right angled yellow connec
43. e Data Management screen 1 Load Opens the selected file 2 Edit Lets you add identifiers and notes to a saved file 80 Data Management 9 1 8 2 Identifying Saved Files 3 Delete Erases the saved file s from storage memory 4 Copy Lets you copy the selected file s from one CF slot to the other 5 Move Lets you move the selected file s from one CF slot to the other 6 Select All Selects all files 7 Information Lets you see how many saved files you have and how much memory is available 8 Setup Provides a shortcut to the Save Data utility dialog box that lets you set the location where files are saved See Save Data on page 89 for details 9 Lock Status Indicator Displays a lock icon when indicating that the file is factory installed 10 Storage Location Indicator Indicates to which CF card the file is saved 11 Additional Information Displays module source type of data Screen movie or snapshot date time any custom notes lock status and storage location information Identifying Saved Files Saved files can display the following identification information e Year is the vehicle model year e Make is the vehicle manufacturer e Sensor is the component tested e Condition is for good bad or unknown status options For related information refer to the following sections e Saving Data on page 43 e Editing Saved Files on page 82 Loading Saved
44. e items such as buttons and menu options Example e Press the Y a button 1 1 2 Symbols The following types of arrows are used The greater than arrow gt indicates an abbreviated set of selection instructions Example e Select Utilities gt Tool Setup gt Date The above statement abbreviates the following procedure 1 Navigate to the Utilities button 2 Use the Thumb Pad to navigate to and highlight the Tool Setup submenu 3 Use the Thumb Pad to navigate to and highlight the Date option from the submenu 4 Press Y a to confirm the selection The solid arrows e c d b refer to the four directions of the Thumb Pad Example e Press the down d arrow Using This Manual 1 1 3 1 1 4 Conventions Terminology The term select means to highlight a button or menu item using the Thumb Pad and then pressing the Y a button to confirm the selection Example e Select Reset The above statement abbreviates the following procedure 1 Navigate to and highlight the Reset button 2 Press the Y a button Notes and Important Messages The following messages are used Notes A NOTE provides helpful information such as additional explanations tips and comments Example NOTE For additional information refer to Important IMPORTANT indicates a situation which if not avoided may result in damage to the test equipment or vehicle Example IMPORTANT Do not force the CompactFlash
45. e kavbnarn in aud Figure 9 16 Sample Shop Information dialog box Plug in a USB keyboard not supplied Type the shop identification information in the available data fields Press Esc to close the dialog box and unplug the keyboard Select Utilities gt Shop Info to verify that the identification information displays properly and press N X to close the dialog box A message offering to include your information as a header on your printed pages displays Figure 9 17 aa PO 95 Utilities System Info Figure 9 17 Sample Shop Info header printing message 6 Press Y a or N X to choose your printing preference 9 8 System Info Select System Info to display your unit s configuration information P To view unit configuration information 1 Scroll to select Utilities gt System Info The System Information screen displays Figure 9 18 Figure 9 18 Example System Information screen 2 Press the down d arrow to view the following screens of information 3 Press the up b arrow to return to the previously viewed screen or press N X twice to return to the main menu 96 10 1 10 2 10 2 1 10 3 Maintenance This section explains the following maintenance issues e Cleaning and damage inspection e Battery pack e CompactFlash cards e Storage tips e Disposal requirements environmental hazards Cleaning and Damage Inspection When using the Vantage PRO unit make sure to do the follow
46. e likely noise could be a problem Testing an O2 sensor using a 1 or 2 volt scale or testing with an amps probe would be examples of when Filter might be used Due to the conversion factors used by the probes a very small volts scale is used to measure the output of the probe For a probe with a conversion factor of 100 mV A connected to a 2 amp load the scope would use a 200 mV scale to measure the output ofthe probe The scope then converts the measured output to 2 amps for display on the screen In Figure C 7 2 low amps probes were connected to the same injector to compare the waveform with Filter on and off CISS j sii pi ff a bf ib it i oe i a i ee pe i Al El Ml L ee Y LL Figure C 7 Sample Noise Filter two low amp scope probes Chamnel 1 uses the Filter and Channel 2 does not use the Filter Notice the difference in readings 109 Using Sensitivity Adjustment Sensitivity Adjustment is used in the Ignition Scope to set the detection sensitivity of cylinder firings See Sensitivity Adjustment on page 71 and Missed Cylinder Detection on page 72 for additional information D 1 When To Use Sensitivity Adjustment The sensitivity adjustment affects the ability of the ignition scope to detect ignition firings Generally it is best to set the sensitivity level just above the spark Figure D 1 EEH ZO AS rar 5 ms En A Figure D 1 Sample of correct sensi
47. e the menu P To change the channel setup 1 Select Channel Number The channel setup menu displays Figure 5 48 2 Select the channel you want to change Ch 1 or Ch 2 3 Select the Peak Detect or Filter channel setup option Probe The Probe button Figure 5 50 lets you select a different test Mor MC Owel 90 ar MC owal 60 Pee O00 psi Press f Duty Cycle e 500 psi Press me Pulse Width br 100 psi Press gir inj Pulsa Widih 3 aie Low Arps dd Ca Ohm n Low Amps 20 ola AL ra dE Amps Intarral Vole OC ave a ls a A A Fo 4 y mp e H z TLA Er af i id E y a i ke ase an AE z 2 Figure 5 50 Sample Probe button and menu P To select a different test 1 Select the Probe button The Probe menu displays Figure 5 50 2 Select an option The Probe button changes to indicate your selection Scale The Scale Figure 5 51 button lets you select a measurement scale for each channel 52 Component Test Operations Performing Tests i ee ee gee i ig me iT EEE gt Y q p P MEA DOS 200 ms oT TS Figure 5 51 Sample Scale button and menu P To select a measurement scale 1 Select Scale The Scale menu displays Figure 5 51 2 Select an option The Scale button and the waveforms on screen change to reflect your selection Signal Zero Offset The Signal Zero Offset button moves the selected channel s zero 0 position up or down within the test display a
48. erms 59 Component Test Operations Features and Benefits 9 0 9 9 9 10 Features and Benefits Select Features and Benefits to view descriptions of the meter including features and benefits specifications and accessories Also included is a five minute description of how to use the optional demonstration board to generate sample signals The demonstration board helps you learn how to better use the Vantage PRO M unit without a test vehicle How To Select How To to choose from a list of available on screen instructions for performing various tasks such as adjusting the display contrast calculating engine RPM and finding glitches in sensors Drawings are included on the screen along with tips Following is a list of common topics other options may be available on a regional basis e No start Basics provides the ability to diagnose no starts e 10 Minute Electronic Class provides brief instruction in basic electronics and circuit connections e 15 Minute Ignition Class provides an introduction to basic ignition testing e 20 Minute Current Ramp Class provides an introduction to current ramp classes e 02 Sensor and Feedback System Analysis displays the component test meter in the live graphing mode with O2S test tips to help you understand the fundamental concepts of O2S diagnostics e Illustrated Terms and Definitions provides definitions of terms drawings and tips associated with component testing
49. es with the circuit being tested Measures current from components like ignition coils injectors Low Amps 20 fuel pumps and parasitic draw using the Snap on Low Amp Probe Low Amps 40 Measures current from components like fans and electric motors p using the Snap on Low Amp Probe Ignition Probe Measures secondary ignition system voltage using a secondary coil adapter lead and pickups Measures engine vacuum 0 20 inHg using the Snap on 0 100 PSI Transducer 100 psi Pressure Measures fuel systems engine oil and transmissions using the p Snap on 0 100 PSI Transducer Measures transmissions compression and AC high side pressure using the Snap on 0 500 PSI Transducer 100 psi Vacuum 500 psi Pressure Measures ABS power steering and heavy duty hydraulic systems 5000 psi Pressure using the Snap on 0 5000 PSI Transducer _ N Figure 7 4 Sample Lab Scope screen 1 Channel status information 2 Main body 68 Scope Operations Selecting Scope Software 7 1 2 Ignition Scope The Ignition Scope lets you view a secondary waveform using preset ignition pattern display options Figure 7 5 ___ignition Scope iy Parade Cylinder Raster Superimposed Single Cylinder Ignition Figure 7 5 Sample Ignition Scope submenu Connecting to all cylinders of an engine at the same time simplifies cylinder comparison in the following ways e All cylinders can be viewed at once e Eachcylinder i
50. esting See Selecting a Component Test on page 34 Connect to the vehicle Follow the on screen instructions to connect the Vantage PRO unit to the vehicle See Connecting to a Test Vehicle on page 35 Perform the test Follow the on screen instructions to set up test and evaluate test results See Performing Tests on page 35 31 Component Test Operations Identifying the Test Vehicle Identify the Vehicle Select a Component Connect to the Vehicle Perform the Test Figure 5 2 Basic Component Tests operations 5 2 Identifying the Test Vehicle Component tests vary according to vehicle and system Before you can view a list of available component tests you must identify a specific vehicle system Two options are available for identifying a vehicle e New Vehicle ID e Previous Vehicles 5 2 1 New Vehicle ID The New Vehicle ID option requires that you make selections from a series of menus to identify the vehicle to be tested P To identify a new test vehicle 1 From the main menu select Component Tests gt New Vehicle ID The Region menu displays Figure 5 3 Region HS ndi US DOMESTIC US IMPORTS Figure 5 3 Sample Region menu 2 Select from the submenus as necessary If you need to change a selection press the left e arrow to go back one step at a time NOTE As you make selections vehicle identification data displays in the Status bar Figure 5 4 at the bottom of
51. eter See Digital Meter on page 63 P To select a Multimeter option 1 From the main menu select Multimeter gt Graphing Meter or Digital Meter 2 Select a test option 6 1 1 Graphing Meter Selections from the Graphing Meter menu Figure 6 3 configure your Vantage PRO unit to function as a color graphing Figure 6 4 on page 63 or digital meter The table below describes the test options available Dual Graphing Meter Volts DC Volts DC Average Volts AC rms Ohms Frequency Pulse Width Injector Pulse Width Duty Cycle Amps Internal Low Amps 20 Figure 6 3 Sample Graphing Meter menu Table 6 1 Graphing Meter test options part 1 of 2 Dual Graphing Meter Displays two channels automatically Volts DC Measures direct current voltage Measures direct current and uses a filter to remove excess Volts DC Average noise hash on the signal Measures the effective voltage rather than the Peak or Volts AC rms Average voltage Ohms Measures electrical resistance Measures the number of times a signal repeats itself per Frequency SCN Pulse Width Measures the on time of various components Injector Pulse Width aor the on time of the signal that activates the fuel 62 Multimeter Operations Selecting Multimeter Software Table 6 1 Graphing Meter test options part 2 of 2 Measures the ratio of the pulse width to the complete cycle Duty Cycle width the on time of components that cycle on and off l
52. g Delete from the upper toolbar use the right c and left e arrows A confirmation message displays Figure 8 6 Figure 8 6 Sample Delete file confirmation message Press N X to cancel or press Y a to permanently erase the data from memory Copying and Moving Saved Data The Copy and Move functions let you change the CF card location of your saved data These functions require the use of an additional CF card in the CF 2 slot To copy or move data 1 2 Insert a CF card in the CF 2 slot not supplied From the main menu select Saved Data gt Data Management The Data Management screen displays Figure 8 2 on page 80 From the upper toolbar select Setup The Save Data dialog box displays Select your source CF card slot as the Save To option and press N to close the dialog box When selecting a file from the list on screen use the up b and down d arrows When selecting Copy or Move from the upper toolbar use the right c and left e arrows A confirmation message displays Press Y a to acknowledge the message and close the dialog box You return to the Data Management screen To verify data copied or moved la Leave the destination CF card installed IMPORTANT When your Vantage PRO unit is powered on never remove the master program card from the CF 1 slot 2 From the upper toolbar select Setup The Save Data dialog box displays Select your destination CF card slot as the Save To option and press N
53. g a longer sweep where it will be easy to see Figure B 7 illustrates a TPS Glitch captured using a 10 second sweep Compare this illustration with Figure B 5 on page 103 103 Using Peak Detect When Not to Use Peak Detect eae Figure B 7 Sample 10 Second Sweep TPS Glitch captured B 2 When Not to Use Peak Detect Peak Detect puts the scope in a high speed sampling mode which can pick up and display unwanted noise from components such as injectors and solenoids B 2 1 Example Testing an Oxygen Sensor An Oxygen O2 sensor signal is relatively slow and requires a clean noise free pattern for an accurate diagnosis Peak Detect should be off when testing an O2 sensor because the waveform is much cleaner and easier to evaluate since less noise displays Figure B 8 Figure B 8 Sample O2 waveform with Peak Detect off When Peak Detect is on more noise is picked up which makes diagnosis difficult Figure B 9 104 Using Peak Detect Peak Detect and the Graphing Meter Figure B 9 Sample O2 waveform with Peak Detect on B 3 Peak Detect and the Graphing Meter The Graphing Meter uses a combination of Filter and Peak Detect modes Filter removes the unwanted ignition and other high frequency signals from the display which gives a better view of the signal of interest The combination of Filter and Peak Detect gives a good balance between detecting fast glitches and preventing unwanted noise from displaying The N
54. ge 36 e See Pausing Data on page 37 e See Reviewing Data on page 38 e See Using Zoom on page 38 73 Scope Operations 7 3 Using Presets e See Using Cursors on page 39 e See Taking Snapshots on page 40 e See Resetting Gauges on page 42 e See Saving Data on page 43 e See Printing on page 44 e See Using Setup on page 44 e See Calibration LED on page 50 e See Adjusting Channel Settings on page 50 e See Setting the Sweep Time on page 54 e See Setting the Trigger on page 55 Using Presets A preset is the configuration of your screen setup The Presets option gives you access to all of your custom presets and factory installed presets for commonly tested components Custom presets can be saved from any of the Scope tool Save menus Figure 7 14 See Saving Data on page 43 for more details FA Save Frome cave Preseal Figure 7 13 Sample Save Preset option The Presets Management screen Figure 7 14 displays a list of all the available presets NOTE Aliernatior Dode Ripple 2W Atsralor Moda Ripple SO0m y Cam and Crank Signal Palahonship Fuel Pump 14 AC coupled Grad Ctrl injeciors and Solenoids High Erequanoy AL Signal E High Frequency Digital S preal Injector Currerd Ramp Tesi Low Frequency AC Signals b ommi Eremo eee Pipa Oe Figure 7 14 Sample Preset Management screen O Factory installed presets are iden
55. ges Confirmation messages inform you when you are about to perform an action that cannot be reversed or when an action has been initiated and your confirmation is needed to continue When a user response is not required the message displays briefly before automatically disappearing 4 4 2 Warning Messages Warning messages inform you when completing the selected action may result in an irreversible change or loss of data 4 4 3 Error Messages Error messages inform you when a failure has occurred Example causes of possible errors include e when a cable is disconnected e when a printer is powered off 30 Component Test Operations This section describes features that are accessible from the Component Tests menu New Vehicle ID Previous Vehicles Component Tests Af Index Features amp Benefits How To Power User Tests BUICK FUEL INJECTION 2005 LACROSSE 3 81 VI 0153P Bl Figure 5 1 Sample Component Tests menu The Component Tests menu Figure 5 1 provides the following options New Vehicle ID Previous Vehicles Component Tests A Z Index Features and Benefits How To Power User Tests 5 1 Component Tests The following is an outline of basic component testing operations 1 Identify the vehicle lIdentify the test vehicle or select from a list of previously identified vehicles See Identifying the Test Vehicle on page 32 Select a component test Select a vehicle specific component for t
56. harger unit Allow the battery pack to cool first For optimal battery charging the ideal room temperature is 77 F 25 C 5 2 Vertically insert the battery pack into the charger Figure 3 1 17 Getting Started Supplying Power Figure 3 1 Battery pack charge orientation 1 Battery pack 2 Battery charger 3 DC power jack 4 Charge status lights When charging begins a red status light displays 3 Letthe battery pack charge until a steady green status light displays When the battery pack is too hot too cold or unable to hold a charge both red and green charge status lights will flash If the charge status lights flash for more than two hours the battery pack may need replacing See Battery Pack Not Charging on page 99 NOTE O A fully discharged battery pack takes four hours to charge P To install the battery pack e Remove the right handgrip and insert the battery pack into the vacant battery slot Figure 3 2 Figure 3 2 Battery pack slot P To extend the life of the battery pack e Before recharging the battery pack let it become completely discharged 18 Getting Started Supplying Power A four minute warning will display before the battery pack becomes completely discharged Figure 3 3 Battery low system wall turn of in 4 rmrirndels Press to corninue Figure 3 3 Sample low battery warning P To continue working after the battery warning displays e Choose and connect a
57. his section explains how to view component information The following is an outline of basic testing operations 57 Component Test Operations Viewing Component Information 1 Identify the vehicle dentify the test vehicle to the Component Tests module or select from a list of previously identified vehicles 2 View component information Display up to four categories of vehicle specific component information See Viewing Component Information on page 57 for details 5 6 1 Identifying the Vehicle The vehicle identification process is the same as for vehicle testing See Identifying the Test Vehicle on page 32 for information 5 6 2 Viewing Component Information Once the test vehicle is identified you can select the Component Tests function from the Component Tests menu The main body of the Component Information screen Figure 5 62 can contain one or more of the following sections e Operation gives you a general description of normal component operation e Connector displays the component connector and gives you pinouts and wire color information e Location helps you locate the component and tells you where to test it e Technotes gives you component test related tips for example common failures or faults as well as update or recall information OPERATION COMMECTOR Enhiarced EVAD system ute a VIEW HARNESS SIDE purge colencid wer solenotd BACKPROBINGS PLAGE 2 Fuel Lenk pretvure senor SOLE
58. ike EGR or canister purge from 0 100 Amps Internal Measures current for component and parasitic draws under p 10A when connected in series with the circuit being tested Measures current from components like ignition coils Low Amps 20 injectors fuel pumps and parasitic draw using the Snap on Low Amp Probe Low Amps 40 Measures current from components like fans and electric p motors using the Snap on Low Amp Probe MC Dwell 60 Measures carburetor Mixture Control Solenoids 0 60 MC Dwell 90 Measures fuel system Mixture Control Solenoids 0 90 166 osi Vacuum Measures intake manifold vacuum 0 20 inHg using the d Snap on 0 100 PSI Transducer Opel Pressure Measures fuel systems engine oil and transmissions using p the Snap on 0 100 PSI Transducer 500 osi Pressure Measures transmissions compression and AC high side p pressure using the Snap on 0 500 PSI Transducer Measures ABS power steering and heavy duty hydraulic eee Pe LETESSUTG systems using the Snap on 0 5000 PSI Transducer IF 911 Figure 6 4 Sample Graphing Meter screen 1 Channel status information 2 Main body 6 1 2 Digital Meter selections from the Digital Meter Figure 6 5 menu configure your Vantage PRO M unit to function as a Digital Volt Ohm Meter DVOM Figure 6 6 The table below describes the test options available 63 Multimeter Operations Selecting Multimeter Software antnage PRO W Volts DC Volts DC
59. ing e Before and after each use check the housing wiring and connectors for dirt and damage e Atthe end of each working day clean the housing wiring and connectors with a soft cloth and gentle all purpose cleaner IMPORTANT Avoid using abrasive or corrosive cleaning products especially when cleaning the screen Battery Pack To prolong the life of your battery pack when your Vantage PRO unit is not in use power off your Vantage PRO unit and remove the battery pack Replacing the Battery Pack When your battery pack no longer holds a charge call your Snap on dealer to order a new one Refer to Using the Battery Pack on page 17 for more details After replacing the old battery call Rechargeable Battery Recycling Corporation RBRC at 1 800 822 8837 USA or refer to their web site at http www rbrc org for the nearest recycling location and instructions for proper battery disposal 10 Amp Fuse The Vantage PRO unit uses one 10 amp mini fuse to protect the amp circuit The fuse is located in the back of the unit Figure 10 1 97 Maintenance CompactFlash CF Cards BEEEEEEEE EEE E EEE EE ELELELY ba w Ii ki A tr MA A pr w amp Figure 10 1 Sample Fuse location If undamaged the fuse should never need replacing IMPORTANT Follow the precautions below to avoid damage to the tool e Do not reverse the vehicle power connection to a battery while using the test leads e
60. ion Connections e Exits a menu or program e Moves the highlight between the upper and lower parts of the screen 2 5 3 Thumb Pad The Thumb Pad c e b d moves the highlight around the screen for making menu or field selections and is typically used in combination with the Y a and N X buttons 2 5 4 Brightness Contrast Button The Brightness Contrast button lets you adjust the screen for optimum viewing See Adjusting Brightness and Contrast on page 20 for details 2 5 5 S Button The S button can be customized to perform different functions from the Utilities gt Tool Setup menu See S Button on page 91 for details 2 5 6 Power Button The Power button powers the Vantage PRO unit on and off The option to put the unit in Standby mode is also available See Powering Off the Unit on page 22 for details 2 6 Connections The Vantage PRO unit uses the following connections Figure 2 3 on page 5 e Test lead jacks e DC power jack e USB port 2 6 1 Test Lead Jacks Standard safety banana jacks are used with test leads For related information see the following sections e Leads and Clips on page 15 e Connecting Leads and Clips on page 21 12 Introduction Power Sources 2 6 2 DC Power Jack The DC power jack can be used to power the unit with the AC DC power adapter For related information see the following sections e AC DC Power Adapter on page 13 e Connecting the AC
61. l active channels and the Scale button displays the full scale value Figure 5 37 e Units Division the scale value for a major grid division is displayed in the Channel Status Area and the Scale button Figure 5 38 e Full Scale the scale value for the whole grid is displayed in the Channel Status Area and the Scale button Figure 5 39 45 Component Test Operations Performing Tests El 2006 CTS 3 6L VIH 7 ison oe CTS 3 5L VIN 05004 oe 13 CADILLAC FUEL INJECTION Figure 5 39 Sample Full Scale selected NOTE The Units dialog box can also be accessed from the Utilities menu located on the Tool Setup submenu as described in Units on page 87 P To change units 1 Select Setup gt Units The Units dialog box displays Figure 5 36 on page 45 2 Change the unit values as needed 3 Press N X to close the dialog box Ignition System Before ignition testing can begin the ignition system type and any relevant parameters should be selected Selecting Ignition System displays the Ignition System dialog box Figure 5 40 that lets you select the following for the test vehicle e Ignition type 46 Component Test Operations Performing Tests gt e Number of cylinders e Cylinder firing order e 1 Trigger Inductive RPM Pickup connection e Cylinder firing polarity e RPM factor Ignition System ignition Type Cyis Firing Order 4 Trigger Set 24 Trigger to Plug
62. le of Contents Features and BeNGInS ainia Add Aca 60 HON io a aa a aaa 60 Power User TOS Sieni A A ls 60 Chapter 6 Multimeter Opera iii iia caGiEiS 61 Selecting Multimeter SORWALEC seraa a a a a 62 Graphing Meter issia a E A 62 Digtal Mela aria rro dni 63 Feromina Multimeter Tests tdi A AAA A A Ad 65 Chapter 7 Scope Operations urls 66 Selecting Scope Software 21001 A os 67 EAU de 67 A o a eudualtada 69 PCHORMING Scope Resaca cial tane ame A ment ctalocetiaranneadisamoaunenmns 73 ISI Presi st de ee cece ead ee 74 EGading Saved PrCSelS i sita iii 75 E GING FICSCUS ind AA a a A 76 Deleting PreSets ccccsccccssscccesseccseececeeeeecceucesseueeeceueceseueeecsuseessaueessageesseueeessueeessaeeessaseees 77 CONG and MOVING Presea ln la 78 Selecting Multiple PRES CTS veces signi scones ira 79 Chapter 8 Data Management tous ai 80 dentiivind Saved Fleur is ada cos ida 81 orto dtes seats sanecenddnataca ste adet a a aE AE 81 Editing SAVEA Als ii a ane Aad easton 82 Deleting Saved Flete 83 Copying and Moving Saved Data occcccccoccncccconnnncnonncnnnnnncnnnononcnnnnnnnronnnnancnnnnnnnnnnnnnannnnnnnnrinnnnnns 84 Ele AI PCS caos ia 85 Backing Wp Saved Files as 85 Chapter 9 WUNUGS css o dao 86 A oo A tenet ecu at eltteat 86 nn teeta heel ta dart heal betlta stants cabbies deel a a detest tobe teases 87 ONON SY SCCM seats a O aR etal hla tale 88 Power Managemen ccccssscecceseeccescecceuseccssececeuscecseueessagecc
63. maintain a spark across the spark plug electrodes e Spark Duration Burn time the spark is maintained across the spark plug electrodes Min Max and current values for Firing kV Spark kV and Spark Duration are displayed for each cylinder in the firing order Intermittent problems that happen too fast to be seen on the live waveform will be captured in the Min Max reading making it possible to spot problems that can be difficult to see in the live waveform Figure 7 12 Figure 7 12 Sample digital kV view Multiple Spark Ignition Systems On vehicles with multiple spark ignition systems when more than one spark per cylinder is present Firing kV FKV is calculated at the start of the first soark and Spark kV SKV and Burn are calculated from the last spark P To calculate the Digital kV and Burn measurements e Select an ignition pattern with a 10 ms sweep such as Parade 10 ms or Cyl 10 ms when testing a multiple spark system IMPORTANT Digital kV cannot be correctly calculated if in the Ignition Scope view the end of the last spark for each cylinder is near the end of the screen or off of the screen 7 2 Performing Scope Tests When performing tests with the Scope the toolbars and controls work the same as those in Component Tests Button and menu option availability vary depending on your test selection For related information see the following Component Tests Operations sections e See Changing Views on pa
64. n Figure 7 14 on page 74 7 3 3 Deleting Presets The Delete button deletes preset files from system memory 17 Scope Operations Using Presets P To delete presets 1 From the main menu select Scope gt Preset The Preset Management screen displays Figure 7 16 on page 75 Highlight a preset from the list Select the Delete button A confirmation message displays Figure 7 20 Figure 7 20 Sample Delete file confirmation message Permanently remove the preset from memory by pressing Y a After processing your delete request you are returned to the Preset Management screen 7 3 4 Copying and Moving Presets The Copy and Move buttons let you change the storage location of your custom presets These functions require the use of a CF card in the CF2 card slot Copy and Move presets go to the inactive CF card For example If you designate the CF1 as your Save To storage memory preference when you use the Copy and Move buttons your selected preset goes to CF2 Inactive CF card P To copy or move data 1 2 Insert a CF card in the CF2 card slot not supplied From the main menu select Scope gt Preset The Preset Management screen displays Figure 7 16 on page 75 From the upper toolbar select Setup The Save Data dialog box displays Select your source storage memory preference from the Save To options and then press N X to close the dialog box This will be the storage memory you will
65. n also be used to power the Vantage PRO M unit See AC DC Power Adapter on page 13 for more details 2 7 4 Vehicle Auxiliary Power Cables Optional The Vantage PRO unit can be powered from a vehicle using the optional Lighter Power Cable and the optional Battery Power Cable Figure 2 10 14 Introduction Leads and Clips Figure 2 10 Optional vehicle power adapters 1 Battery Power Cable 2 Lighter Power Cable NOTE If powering from a vehicle battery using the Battery Power Cable the Lighter Power Cable is also required 2 8 Leads and Clips The Vantage PRO kit includes the following standard leads and clips e Channel 1 lead e Channel 2 lead e Alligator clips IMPORTANT Pull on the connector not the wire to remove the leads from their jacks Pulling on the wire can damage the leads See Connecting Leads and Clips on page 21 for more details 2 8 1 Channel 1 Lead The shielded yellow lead is used for Channel 1 Figure 2 11 The lead color matches the color of the CH1 jack on the Vantage PRO unit and the trace color of Ch 1 on the test screens A stackable black right angle ground plug is attached 95 E lt A Figure 2 11 Yellow Channel 1 Lead 15 Introduction Leads and Clips 2 8 2 Channel 2 Lead The shielded green lead is used for Channel 2 Figure 2 12 The lead color matches the color of the CH2 jack on the Vantage PRO unit and the trace color of Ch 2 on the tes
66. n if the signal does not cross the trigger threshold the screen automatically updates after a short period so you can see the waveform which lets you set a threshold to optimize viewing 55 Component Test Operations Performing Tests Normal updates the screen when the signal crosses the trigger threshold in the selected direction rising or falling Ifthe signal does not cross the trigger threshold the screen will not update which lets you capture intermittent events because the screen only updates when the signal meets your trigger selection e Cyl triggers the scope from the RPM lead signal The lead detects the firing on the plug wire that the lead is connected to and the scope uses this signal to trigger the display You can only adjust the time offset for this Trigger type Auto updates the screen when the scope receives a signal from the RPM lead Even if the signal does not receive a signal from the lead the screen automatically updates after a short period so you can still see the waveform Normal updates the screen when scope receives a signal from the RPM lead Ifthe scope does not receive a signal from the lead the screen will not update P To select a trigger type 1 Select the Trigger Type button The dropdown menu displays Figure 5 57 2 Select an option With the exception of None a submenu displays 3 Select Auto or Normal from the submenu lfa Channel trigger Ch1
67. nated storage CF card from the User Data directory e S Button Popup opens this menu when the button is pushed P To assign a function to the S button 1 Select Utilities gt Tool Setup gt S Button 2 The S Button dialog box displays Figure 9 11 91 Utilities System Tools S Tn Popup Figure 9 11 Sample S Button dialog box 3 Select a function from the drop down list The drop down lists close when Y a is pressed 4 Press N X to close the dialog box 9 1 9 Color Theme Selecting Color Theme lets you change the background on the display Using the black background helps conserve battery power P To change the screen background 1 Select Utilities gt Tool Setup gt Color Theme The Color Theme dialog box displays 2 Press Y a to open the dropdown list Figure 9 12 Color Theme Alternate White Figure 9 12 Sample Color Theme dialog box 3 Select a function from the dropdown list 4 Press N X to close the dialog box 9 2 System Tools The System Tools menu Figure 9 13 lets you add programs update the system software and restore your software 92 Utilities Tool Help System Tools Add Program _ System Restore Figure 9 13 System Tools sample menu The System Tools Setup submenu includes e Add Program e System Restore 9 2 1 Add Program When specified select Add Program to add additional programs to your Vantage PRO software Follow the installation instruction
68. nes 2 eit 1 3 2 digits da 4 ai inductive 1 rom 8 2 digits 1 rom 3 2 digits 10 rom 0 1 mV 0 001 V Volts AC RMS 1 5 4 digits On Volts DC Channel 1 1 0 2 digits Range 0 005 s TEE pos eo A 025 A Ps EJ el Bs p UP po o2 1b o 19 p o ad ma O O Accuracy measured at 25 C is shown as of reading Number of least significant digits For example a 100V DC signal accuracy reading would be 0 25 2 digits or 99 75 to 100 25 2 digits or 99 73 to 100 27 10 Introduction 2 9 Control Buttons Funcion Range Reston Accuracy 0 1 mV 0 5 0 001 V 1 0 001 V 2 0 001 V Volts DC pac Channel 2 5 o o1v 1 0 2 digits 10 0 01 V 50 50 a V 1Accuracy measured at 25 C is shown as of reading Number of least significant digits For example a 100V DC signal accuracy reading would be 0 25 2 digits or 99 75 to 100 25 2 digits or 99 73 to 100 27 Control Buttons The Vantage PRO unit Figure 2 2 on page 4 has the following control buttons e Y a button e N X button e Thumb Pad c e b d e Brightness Contrast button e S button e Power button 2 5 1 v a Yes Button The Y a button does the following e Selects the item you highlighted using the Thumb Pad e Toggles between cursors 2 5 2 N X No Button The N X button does the following 11 Introduct
69. of the Threshold value for reference Measuring the Min and Max may take a few seconds 2 Change the Threshold value and the Slope as needed NOTE O Threshold can only be changed to a value that is between the Min and Max of the signal 3 Press N X to exit the dialog box 5 5 14 Setting the Sweep Time The Sweep button sets the amount of time it takes for data to display across the screen from left to right P To change the sweep time 1 Select Sweep The dropdown menu displays Figure 5 55 54 Component Test Operations Performing Tests Figure 5 55 Sample Sweep menu 2 Select an option NOTE O Sweeps shorter than 1 second will collect some frames after the Pause button is selected The faster the sweep the more frames will be collected 5 5 15 Setting the Trigger Use the Trigger control bar Figure 5 56 to set the criteria to start the display of data md iow IA 10 ms Figure 5 56 Sample Trigger control bar 1 Trigger Type 2 Slope 3 Trigger Position Trigger Type Selecting Trigger Type lets you set the criteria used to start the display of data Available Trigger Type menu options include e None displays data as fast as it is received e Ch 1 2 triggers the display based on the signal from the selected channel Available submenu options include Auto updates the screen when the signal crosses the trigger threshold in the selected direction rising or falling Eve
70. oise Filter can be selected from the Channel Control bar as applicable For related information see the following sections e Adjusting Channel Settings on page 50 e Scope Filter Use on page 109 105 Using Noise Filter If glitches are being detected and no vehicle problems are observed noise may be the cause As a precaution do the following e Use shielded leads e Route the leads away from secondary ignition components e Verify the test connections e If noise is still suspected to be a problem turn on the Filter See Channel Number on page 51 for procedures NOTE O The Filter may also eliminate extremely fast glitches C 1 When to Use Filter The following sections explain when to use the filter with the Graphing Meter and the Scope C 1 1 Graphing Meter Filter Use In the Graphing Meter the filter minimizes noise by ignoring or smoothing out fast spikes Calculated Measurements When conducting a calculated measurement test Frequency Pulse Width MC Dwell or Duty Cycle the filter is used to ignore very fast spikes 20 uS and faster from sources like the ignition system Figure C 1 illustrates noise from the ignition system when conducting the Graphing Meter Frequency test with Peak Detect on and Filter off 106 Using Noise Filter When to Use Filter Figure C 1 Sample of Frequency with Filter off Figure C 2 illustrates the noise filtered out when conducting the same test with
71. ompare the secondary waveform for all engine cylinders Figure 7 6 69 Scope Operations Selecting Scope Software e The Parade pattern displays the secondary waveform for each cylinder in the firing order from left to right across the screen e The Cylinder pattern displays the secondary waveform for the selected cylinder e The Raster pattern displays the secondary waveform for each cylinder in the firing order starting with cylinder number one at the bottom e The Superimposed pattern displays the secondary waveform for each cylinder in the firing order stacked on top of each other Figure 7 6 Sample ignition pattern screen Single Cylinder Ignition The Single Cylinder Ignition option Figure 7 7 configures the scan tool to connect to an individual cylinder using a fixed time sweep when a lead Is not available to connect to all cylinders Parade Cylinder Raster Superimposed Figure 7 7 Sample Ignition Scope submenu Ignition Scope Probe In the lower toolbar the Channel One 1 Probe button setting is restricted to Ignition Probe The Channel Two 2 Probe button setting is not restricted and functions the same as in the Lab Scope See Probe on page 52 for more details 70 Scope Operations Selecting Scope Software ty Oi played Lai ln verted AL Auto Find Figure 7 8 Sample Channel one s fixed Peak Detect option Sensitivity Adjustment The Sensitivity Adjustment button Figure 7 9 lets
72. plays with saved data P To set the date 1 From the main menu select Utilities gt Tool Setup gt Date The Date dialog box displays Figure 9 9 Day Month Year Style 6 flan poos mmboyr 13 a wie Figure 9 9 Sample Date dialog box 2 Select from the drop down lists as necessary The drop down list closes when Y a is pressed 90 Utilities Tool Setup 3 Press N X to close the Date dialog box 9 1 7 Time Select Time to set the time that displays at the bottom of the screen P To set the time 1 From the main menu select Utilities gt Tool Setup gt Time The Time dialog box displays Figure 9 10 Hour Minutes 12124 2 Select from the drop down lists as necessary The drop down list closes when Y a is pressed 3 Press N X to close the Time dialog box 9 1 8 S Button Select S Button to change the functionality of the S button Possible assignments include e Freeze Run works as the Pause Play button when viewing data in graph view e Print Page works like the Page or Full Screen options from the Print button on the toolbar NOTE The S button can only perform print functions when the Print button is visible in the upper toolbar e Save Image is the default and makes a bitmap BMP or JPEG JPG screen capture image of any screen during any mode of operation NOTE Using an optional CF card reader writer connected to your computer saved bitmap files can be retrieved from your desig
73. r options such as a storage CF card Battery Pack Nickel metal hydride Rechargeable External Battery Charger Input 100 240 V AC 0 5A 47 63 Hz Fuse 10 Amp ATO Mini AC DC Adapter 2 5mm DC plug Input 100 240V AC 0 5A 47 63 Hz Output 15V DC O 1 2A Dimensions Width 11 75 inches 298 45 mm Height 6 90 inches 175 26 mm Depth 2 40 inches 60 96 mm Weight including battery pack 3 lbs 12 5 oz 1 509 Kg Operating Temperature Range 32 to 122 F 0 to 50 C Storage Temperature Range 4 to 140 F 20 to 60 C 2 4 Operating Specifications The following tables detail the Vantage PRO unit operating specifications for Introduction Operating Specifications e Scope capabilities e Test instrument capabilities 2 4 1 Scope Capabilities The following tables Table 2 1 and Table 2 2 detail the Scope capabilities for e Analog to digital A D conversions e Horizontal sweep and frame storage Table 2 1 Scope Analog to digital conversions Charnes Common grounds Resolution 12 bits EE Table 2 2 Scope Horizontal sweep and frame storage Data Points Buffer Storage per Channel per Channel 1305 screens 2o See K data points 1048 screens eo gas K data points TBuffer storage consists of contiguous screens of 2 channel data 2 4 2 Test Instrument Capabilities Test instrument capabilities are shown in the table below Function Range Resolution Accuracy 0 001
74. rame when Pause was pressed e Frames captured before Pause was pressed are negative e Frames captured after are positive There are two ways to review paused data e Manually e Automatically To manually review data 1 Select Pause 2 Select Review 3 Use the right c and left e arrows to review data one frame at a time 4 Usethe up b and down d arrows to review data a fraction of a frame at a time when possible NOTE You cannot review fractions of frames in the Ignition Scope To automatically scroll paused data 1 With the Review button selected press Y a again to display the menu of scroll options Figure 5 18 4 Auto Soroll Fast 4 Auto Scroll Slow Figure 5 18 Sample Review scroll menu 2 From the Review menu select an Auto option Auto Scroll Fast automatically scrolls the paused data on screen at full speed Auto Scroll Slow automatically scrolls the paused data on screen at half speed 3 Press N X to close the menu and stop automatic scrolling Using Zoom The Zoom button lets you change the magnification of paused data and appears in place of the Snapshot button when the display is paused 38 Component Test Operations Performing Tests P To zoom paused test screens 1 Select Zoom A dropdown menu displays Figure 5 19 y a E 4 7 2 a de ra a P 10 F FORD FUEL INJECTION 2006 FOCUS 20L ZETEC 0159P BM Figure 5 19 Sample Zoom op
75. re 5 44 PET Peery AAA r AS E Uritz UEU TE Santon sytem 00 Grid Tigger Display Scales Display Inverse Colors Figure 5 44 Sample Inverse Colors screen 49 Component Test Operations Performing Tests Save Data This selection opens the Save Data dialog box Figure 5 28 which lets you choose how and where files are saved 5 5 12 Calibration LED When you select a Diodes Continuity Ohms or Pressure transducers test a message displays with calibration instructions Figure 5 45 Make sure pe fe cameo to sc Cht bit ut not th he vehicle i comen J calibration values Figure 5 45 Sample calibration procedure message When the test screen displays the LED Figure 5 46 on the toolbar indicates the following channel calibration status e Green calibrated e Red not calibrated using previous calibration values Figure 5 46 Sample calibration LED 5 5 13 Adjusting Channel Settings The Channel control bar Figure 5 47 lets you adjust channel settings and viewing characteristics for the selected trace Figure 5 47 ame Channel control bar 1 Channel Number 2 Probe 3 Scale 4 Signal Zero Offset 5 Raster Spacing Ignition Scope Only 50 Component Test Operations Performing Tests Channel Number The Channel Number button lets you select channel options e Channel One 1 is automatically displayed and cannot be turned off e Channel Two 2 can be
76. re 8 3 Sample Edit Saved Data Notation dialog box NOTE O The Add Note button is only active when a USB keyboard is plugged in 5 Select the Add Note icon The Note section displays Figure 8 4 82 Data Management Deleting Saved Files Edit Saved Data Notation dd Save Hola ear Make Component Condition ZI Po rss orton secondary 6309 Add Adcktiona information Presa ESC when finished Connect a USB keyboard then type in up to 7 lines of additional infor mation here Figure 8 4 Sample Add Note section 6 Using your keyboard type a note 7 lines maximum then press Esc to exit Additional Information 7 Select the Year Make Component or Tested option A drop down list displays Figure 8 5 Edit Saved Data Notation Component Condition fiarstion Secondary Good Figure 8 5 Sample Make list in Edit Saved Data Notation 8 Select options from the drop down lists as appropriate 9 Select Save when you are finished to return to the Data Management screen P To exit Edit Data screen e Press N X to return to the main menu 8 4 Deleting Saved Files The Delete button lets you delete saved test data P To delete files 1 From the main menu select Saved Data gt Data Management The Data Management screen displays Figure 8 2 on page 80 83 Data Management 8 5 Copying and Moving Saved Data When selecting a file from the list on screen use the up b and down d arrows When selectin
77. rea GQ To move a channel s zero position 1 Select Signal Zero Offset The button changes from blue to grey to indicate that the function is selected Figure 5 52 Figure 5 52 Sample Signal Zero Offset selection 2 Press the up b or down d arrows as needed to move the zero point 3 Press N X to exit the function Threshold The Threshold button changes the reference point on the waveform and is only used for calculating measurements like frequency duty cycle MC dwell and pulse width There are two threshold options e Auto Threshold Select ATS automatically picks a threshold level in the middle of the range in which the waveform travels ATS defaults to a falling edge e Manual Threshold Select MTS lets you manually pick a signal level and direction rising or falling to be used as a reference point This is typically used if ATS picks a level that does not give the desired result 53 Component Test Operations Performing Tests P To change the threshold level 1 Select Threshold The Threshold menu displays Figure 5 53 2 Select an option P To use the Manual Threshold option 1 Select Threshold gt Manual Threshold Select The Manual Threshold Select dialog box displays Figure 5 54 Treshold Sigral Shope Fims mo Emo E Lisa arowa to odjust hovel and slope Press H When done Figure 5 54 Sample Manual Threshold Select dialog box The Signal Min and Max display to the left and right
78. reen Layout 1 Play button 2 Position Indicator The Data Buffer cannot be highlighted or selected P To manually scroll through stored frames 1 When the screen is paused select Review 2 Press the left e and right c arrows 4 1 2 Main Body The main body of the test screens displays the following e Channel status information e Digital or graphical test results e Saved data e Cursors e Confirmation messages 4 1 3 Lower Toolbar The lower toolbar controls Figure 4 6 Table 4 2 vary depending on the active mode and stage of operation AE Li iaj 2 m an i a Figure 4 6 Sample lower toolbar Table 4 2 Lower toolbar controls part 1 of 2 ae Lets you select the channel to adjust number Displays the current test connection for the channel Displays the current units of measurement for the channel Moves the selected channel s zero 0 position up or down within the test display area Adjusts the vertical spacing between the cylinders in the Ignition Scope Raster pattern 26 Navigation Making Selections Table 4 2 Lower toolbar controls part 2 of 2 ETT ee Jms Sets the amount of time displayed across the screen Sets the criteria used to start the display of data Trigger Type there are three types of Trigger settings None Channel and Cyl Slope Lets you change the Trigger edge for the specified p channel from rising to falling Triaaer Position Moves the trigger point
79. s displayed once per screen in firing order and is displayed in the same location on screen e The same pattern is displayed regardless of engine rom The Ignition Scope requires the use of two leads e Secondary Coil adapter to display the secondary waveform e Inductive RPM Pickup adapter to identify cylinder number one for proper cylinder order display Refer to Connecting Leads and Clips on page 21 for more details Rom can be calculated from either the grey Inductive RPM pickup adapter or the Secondary Coil adapter If only the RPM or Secondary Coil adapter is used rom will be calculated from whichever lead is connected If both leads are connected rom will be calculated from the grey Inductive rom pickup NOTE The optional SIA 2000 Adapter kit is required to connect to multiple cylinders at once on Wasted Spark distributorless ignition systems Contact your sales representative for details Note the following regarding Ignition Scope synchronization e Synchronization to cylinder number one takes a couple of seconds after you start the engine e Cylinder firings may be observed to change position during the synchronization process e If the Ignition Scope settings are changed cylinder synchronization reoccurs NOTE When testing Waste Spark systems power firings will display on Channel One and waste on Channel Two Ignition Patterns Four ignition pattern options Figure 7 5 on page 69 are available to view and c
80. s that come with the software 9 2 2 System Restore The System Restore function reverts the master storage CF card in slot 1 back into an installation CF card This will cause the system software to be reinstalled P To restore the system software 1 Select Utilities gt System Tools gt System Restore 2 A warning dialog will launch To proceed with restoring your system Press Y a To return to the menu Press N X 3 A confirmation message will appear and the master storage CF card has now been reverted to an installation CF card 4 In order to complete the system restore process turn off the unit 5 Power on the unit The newly reverted installation CF card will begin the installation process When this process is complete the system has been restored 9 3 Tool Help Tool Help provides information from this manual on your Vantage PRO unit GQ To use Tool Help 1 From the main menu select Utilities gt Tool Help The Tool Help Table of Contents screen displays Figure 9 14 93 Utilities Easy Scroll is About Help E Safety Information Introduction Getting Started 2 Navigation INFO Operations 2 Multimeter Operations Scope Operations Maintenance A Data Management Utilities Figure 9 14 Sample Tool Help Table of Contents screen Select a topic from the Table of Contents screen Select a book and press Y a to expand the contents Press the right c arrow to view a
81. safety of others in the work area the equipment being used or the vehicle being tested lt is assumed that the operator has a thorough understanding of vehicle systems before using this product Understanding of these system principles and operating theories is necessary for competent safe and accurate use of this instrument Before using the equipment always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested Use the equipment only as described in this manual Read understand and follow all safety messages and instructions in this manual the accompanying safety manual and on the test equipment Safety Message Conventions Safety messages are provided to help prevent personal injury and equipment damage All safety messages are introduced by a signal word indicating the hazard level Indicates an imminently hazardous situation which if not avoided will result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided could result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided may result in moderate or minor injury to the operator or to bystanders Safety Information Important Safety Instructions Safety messages contain three different type styles e Normal type states the hazard e Bold
82. seuececeueeessaueeesausesseseeeseneeessaees 88 Se Dalt is A caida 89 nn PO PEO In nine eh nan e ose gaan Sect en ease totes 90 BEE E AE EE E A A en ee 90 TINE ersat a aa nro I 91 S DUO rl et 91 Color Tem it caos 92 SA A cs ca than 92 o o A 93 SS SIM CS IONS anna ad 93 A a 93 COM A ciate tastes a ei hat ak cs cencbah Maat esstectia tease ccd 94 CONNEC IO PU es Re eee en ee et 95 nn A rte ease tnenats Sesenae tenet we EE E 95 A aca e atc a tt ee gcse dee oat gn gene nse teed gin Node eagonsuoes enced ecco 95 So An 96 Table of Contents Chapter 10 Maltenan ce iii ts ais 97 Cleaning and Damage Inspection ae a a i 97 Batey Packard oa 97 Replacing the Battery Paca iia 97 DOF FUSE a A A AA A A 97 CompactrlashO CE Cars ii ls 98 SOLACE IS tdo bai sads 98 DISPOSal ACCUM CINGINS oriol rondar 98 APpendix A TrOUDIESNO O MM ita 99 Batten Pack Nota aescu keto a mbes cageeegecaanesenetetane 99 Jat Wil Not Power OMe sett o A a eee as 99 Emergency estaran co dali s ice ian tall oaric citado irc aioiierida iii 99 Appendix B Using Peak Detection nadaa 101 When To Use Peak Deteclansaid a A eee 101 Example Testing Secondary lgnition cccccccncnnccccoccnncoconconononncnonononcnnnnnnncnnnnnancnnonnnnons 101 Example Testing a TPS for GilitCH S oooccccoccncconnnococnnccnannnonnnnononnnnconnnononnnnnannnnnnnos 103 When Notto Use Peak Detection 104 Example Testing an Oxygen Sensor cccooccnnccccccnncccnnnn
83. t Test Leads Connect to the Vehicle Perform the Test Figure 7 2 Basic Scope operations 7 1 Selecting Scope Software There are two types of scope tools available e Lab Scope See Lab Scope on page 67 e Ignition Scope See Ignition Scope on page 69 The following procedures explain how to select a scope tool P To select scope software 1 From the main menu select Scope gt Lab Scope or Ignition Scope 2 Select a test configuration 7 1 1 Lab Scope Selections from the Lab Scope menu Figure 7 3 configure your Vantage PRO unit to function as a two channel display The table below describes the test configuration options available E es gt n LabScope 2 Ch Lab Scope Volts DC Amps Internal Low Amps 20 Low Amps 40 Ignition Probe 100 psi Vacuum 100 psi Pressure 500 psi Pressure 3000 psi Pressure Figure 7 3 Sample Lab Scope menu 67 Scope Operations Selecting Scope Software NOTE O The 2 Ch Lab Scope option remembers all settings that are changed for the next use All other lab scope options will default to the original function Table 7 1 Lab Scope test configuration options Option Function 2 Ch Lab Scope Displays two channels automatically All settings changed in this option will be saved automatically for future use Volts DC Measures direct current voltage Amps Internal Measures current for component and parasitic draws under 10A j when connected in seri
84. t screens A stackable black right angle ground plug is attached HH Figure 2 12 Green Channel 2 Lead 2 8 3 Alligator Clips Three insulated alligator clips are included one yellow and one green clip to match each test lead and one black clip for the ground lead Figure 2 13 Figure 2 13 Alligator Clip 16 3 1 Getting Started This section explains how to get started using your Vantage PRO unit The following procedures are covered Supplying power to the Vantage PRO unit Turning on the unit Adjusting Brightness Contrast Connecting leads and adapters Setting up to print optional Turning off the unit el a aN Supplying Power There are several ways to supply power to the Vantage PRO unit e Using the Battery Pack e Connecting the AC DC Power Adapter e Connecting Vehicle Auxiliary Power Cables 3 1 1 Using the Battery Pack The Vantage PRO unit comes with a rechargeable nickel metal hydride battery pack and an external battery charger For related information see the following sections e Battery Pack on page 14 e Battery Charger on page 14 e Replacing the Battery Pack on page 97 e Battery Pack Not Charging on page 99 Before using the battery pack for the first time you must fully charge it To charge the battery pack 1 Plug the AC DC power adapter into the DC power jack of the battery charger NOTE Do not put a hot battery pack in the battery c
85. ter 105 106 109 Index fuse 7 replacing 97 G grid 47 H help See tool help How To 60 identifying saved files 81 identifying the test vehicle 32 ignition patterns 69 cylinder 70 parade 70 raster 70 superimposed 70 ignition scope 69 73 ignition patterns 69 ignition system 46 Illustrated Terms and Definitions 60 inverse colors 49 J jump bar 29 L lab scope 67 load 80 loading data 75 81 M maintenance 97 98 10 amp fuse 97 battery pack 97 cleaning and damage inspection 97 CompactFlash CF cards 98 disposal requirements 98 storage tips 98 making selections 27 manual conventions notes 1 2 master program CF card 7 MC dwell 9 multimeter digital meter 63 graphing meter 62 operations 61 65 performing tests 65 selecting software 62 117 N new vehicle ID 32 noise filter 51 105 106 109 No Start Basics 60 not powering on 99 O O2 Sensor amp Feedback System Analysis 60 operating specifications 7 11 operating temperature 7 P pausing data 37 PC connect to 95 peak detect 51 101 105 performing tests 35 power button 5 power sources 13 15 Power User Tests See tests presets copying and moving 78 deleting 77 editing 76 exiting 75 loading 75 management screen 75 selecting all 79 using 74 79 previous vehicles ID 33 printer setup 17 printing connecting a printer 90 printing a screen 44 probe 52 71 R reset
86. the filter on TRA E eras Y 299w e a E ME H tori pilina _ Figure C 2 Sample of Frequency with Filter on Direct Measurements When you conduct a direct measurement test in the Graphing Meter Volts Amps or Pressure the filter minimizes the display of very fast spikes by averaging the data When used together Filter and Peak Detect balance capturing glitches and minimizing noise Figure C 3 illustrates Peak Detect on and Filter off during a TPS Sweep with the key on and engine off KOEO 107 Using Noise Filter When to Use Filter Figure C 4 illustrates Peak Detect on and Filter on during a TPS Sweep with the key on and engine off KOEO Volts DE i E F 1 Wd MB s itn Figure C 4 Sample of Noise Filter on TPS Sweep KOEO Figure C 5 illustrates Peak Detect on and Filter off during a TPS test The throttle was snapped with the engine running KOER Compare this with Figure C 6 taken under the same conditions but with the Filter on Welt 293 667 Figure C 5 Sample Noise Filter off TPS Sweep KOER 108 Using Noise Filter When to Use Filter Walts 253 GI lid al Figure C 6 Sample Noise Filter on TPS Sweep KOER C 1 2 Scope Filter Use In the Scope Filter smooths out spikes and fast variations in the waveform which provides a good balance between noise suppression and signal integrity and is most useful on scales of 5 volts and below The lower the volts scale the mor
87. tified by a lock icon alongside their name and cannot be edited deleted copied or moved 74 Scope Operations Using Presets The Preset Management screen toolbars and controls Figure 7 14 work the same way as in the Data Management screen in Saved Data with the exception of editing saved presets See Data Management on page 80 for details P To open the Preset Management screen e From the main menu select Scope gt Presets The Preset Management screen displays Figure 7 14 P To exit the Preset Management screen e Press N X until you return to the main menu 7 3 1 Loading Saved Presets The Load button opens an active test screen with the selected preset P To load a preset 1 From the main menu select Scope gt Presets Figure 7 15 LabScope Ignition Scope Presets Figure 7 15 Scope menu The Preset Management screen displays Figure 7 16 Aliernaior Diode Ripple 21 Albernalor Diode Ripple S00 my Ful Pump 14 AC coupled Cred Ctrl Iinjectors and Solerncids High Frequency AL Signal e High Frequency Digital Sipreals Injector Currerd Ramp Tesi Low Frequency AC Signals i mmia Eem ATA oe Pi bi Em l Figure 7 16 Sample preset load selection 2 Highlight a preset from the list 3 Select the Load button A scope screen displays with your selected preset configuration 15 Scope Operations Using Presets 7 3 2 Editing Presets The Edit button lets you edit presets
88. ting min max data 44 S S button 5 safety information iv saving data 43 scale 52 scales display 49 scope 73 79 capabilities 8 ignition scope 69 lab scope 67 operations 66 77 performing tests 73 presets 74 selecting software 67 single cylinder ignition 70 Index selecting component tests 34 setup options 44 grid 47 zoom 38 ignition system 46 inverse colors 49 scales display 49 trigger display 48 units 45 setup See tool setup ShopStream Connect 22 signal zero offset 53 single cylinder ignition 70 snapshot 37 38 40 42 stand the 6 Standby mode 22 setting 88 storage temperature 7 storage tips 98 sweep 54 system info 96 T technical specifications 7 test instrument capabilities 8 11 test leads connecting 21 tests Power User 60 tips 60 tests leads jacks 12 threshold 53 Auto Threshold Select ATS 53 Manual Threshold Select MTS 53 thumb pad 4 tool help 93 tool setup 86 92 transflective screen 4 trigger display 48 trigger See display trigger U units 45 USB keyboard 76 USB ports 5 13 Utilities menu Connect to PC 95 V vehicle power adapters 14 view options 36 viewing component information 57 118
89. tion selection 2 Select an option from the menu The screen changes to reflect your selection and the on screen Zoom Cursor Line displays Figure 5 20 jp w 2 Figure 5 20 Sample Zoom Cursor Line 3 To see a point of interest in detail a Select Review b Use the left e and right c arrows move the Zoom Cursor Line to the left of the point of interest c Select Zoom gt 1x 5 5 5 Using Cursors The Cursors button Figure 5 21 lets you make digital amplitude frequency and time measurements of test data 39 Component Test Operations Performing Tests ts Dig Alel 15 O eee AS Figure 5 21 Cursors button P To use cursors 1 Select Cursors Two vertical cursor lines display on screen Figure 5 22 p Pr m requency l 12H Delta Tem EFE MinT FORD FUEL INJECTION 2006 FOCUS 20L ZETEC 0159P BM Figure 5 22 Cursors example screen 2 Press the right c and left e arrows to move the selected cursor line Press Y a to change the active cursor 4 Press N X when you are finished setting cursors A confirmation message asks how you want to proceed Figure 5 23 o9 Figure 5 23 Sample Cursors confirmation message 5 Press Y a or N X as desired NOTE O Digital amplitude measurements only display when the screen is in Pause mode P To turn cursors off 1 Select Cursors 2 Press Y a twice The cursor lines disappear 5 5 6 Taking Snapshots The Snapshot button lets you capt
90. tive directions See Adjusting Channel Settings on page 50 B 1 When To Use Peak Detect The following section explains when you might want to use Peak Detect and how it works When Peak Detect is off the scope collects just enough data to plot a waveform across the screen This is the standard mode of operation for many scopes Example If the Sweep setting is 10 seconds and the screen was 100 points wide the sample rate would be 10 times a second If the Sweep setting is decreased to 1 second the sample rate would increase to 100 times a second When Peak Detect is on the scope samples at the maximum rate possible and captures more sample points than needed to plot the screen This lets you catch a fast event or glitch B 1 1 Example Testing Secondary Ignition At a Sweep setting of 1 ms Figure B 1 firing voltage will be captured even if Peak Detect is off the sample rate is relatively fast at this time setting E A ie 1 Jz l E A Figure B 1 Sample 1 ms Sweep Peak Detect off As the Sweep setting is increased the firing voltage may be observed to decrease in height and vary more than usual and the peak firing voltage will not be captured consistently Figure B 2 101 Using Peak Detect When To Use Peak Detect i isi E 7 i 7 i bkbissd h Bd boa rn 7 a a gt i r F a pe E Y i l PF Ha r a_i Figure B 2 Sample 10 ms Sweep Peak Detect off At longer sweeps
91. tivity adjustment D 1 1 Improper Sensitivity Adjustments Setting the cylinder firing sensitivity is essential for the proper display of the secondary pattern e lf the sensitivity is set too high cylinder firings may not be detected and firing peaks may not get detected on multiple spark ignition systems e lf the sensitivity is set too low events other than the cylinder firings may be falsely detected as cylinder firings The following examples illustrate what happens when the Sensitivity Adjustments are set too high and too low Sensitivity Set Too High Cylinder firings may not be detected consistently if the sensitivity setting is too high A blank will be displayed in place of a cylinder that is not detected Figure D 2 Lowering the setting will allow the scope to detect the firings consistently 110 Using Sensitivity Adjustment When To Use Sensitivity Adjustment r Ta amp r 10 gt 1 m ae JS les os iH Figure D 2 Sample of sensitivity adjustment set too high NOTE If a cylinder is not firing at all it cannot be displayed and will remain a blank space on screen Multiple Spark Systems When testing a multiple spark ignition system if the scope sensitivity is set too high firing peaks can be intermittently missed and the Digital kV value does not calculate correctly Figure D 3 ml 20 Jada az el Figure D 3 Sample of missing peaks Lowering the scope sensitivity captures
92. to exit When the Data Management screen displays you should see the file s that you copied or moved from your source CF card 84 Data Management Selecting All Files 8 6 Selecting All Files The Select All button highlights all saved data so you can delete copy or move all of the files simultaneously 8 7 Backing up Saved Files You can back up saved data on your master program CF card to an additional CF card for storage P To back up saved data 1 2 5 6 Insert a CF card in the CF 2 slot not supplied From the main menu select Saved Data gt Data Management The Data Management screen displays Figure 8 2 on page 80 From the upper toolbar select Setup The Save Data dialog box displays Set CF 1 as the Save To option and press N to close the dialog box The test data saved to CF 1 master program CF card displays Press the Select All button to highlight all the saved files at once or highlight an individual file Select Copy or Move to complete the transfer to the CF 2 card P To verify the backup transfer of saved data 1 2 With the CF card in the CF 2 slot from the upper toolbar select Setup The Save Data dialog box displays Set CF 2 as the Save To option and press N to close the dialog box The transferred files should display on CF 2 P To exit the Data Management screen Press N X to the main menu 85 9 1 Utilities This section explains the Utilities menu an
93. tor into the jack labeled CH1 3 Attach the yellow alligator clip to the yellow straight end of the lead and the black alligator clip to the black straight end of the lead 4 Connect both of the alligator clip ends to the test vehicle as needed NOTE Use the black stackable ground plug on the CH1 lead for grounding any other lead requiring a common ground P To connect the Channel 2 lead 1 Plug the black ground plug of the Channel 2 lead into the stackable ground plug of the Channel 1 lead This ground connection shields the Channel 2 lead Plug the right angled green connector into the jack labeled CH2 Attach the green alligator clip to the straight end of the Channel 2 lead Connect the alligator clip end to the test vehicle as needed P To connect for internal amps tests Ay Plug the yellow connector into the blue jack labeled 10A and plug the right angled black ground plug into the jack labeled COM Attach the yellow alligator clip to the yellow straight end of the lead and the black alligator clip to the black straight end of the lead Connect the alligator clip ends to the test vehicle as needed 21 Getting Started Setting Up to Print 3 5 Setting Up to Print Your Vantage PRO unit prints from USB enabled PCL 3 or higher printers Before you can use the Print button in the upper toolbar you must do the following 1 Set up the printer 2 Configure the Vantage PRO unit to print P To set
94. tructions in the jump bar to return to the original screen Figure 4 11 he snap on low amp current Probe har a push buthon ubo sero Feabure Presi lt bo raburn hd Figure 4 11 Sample jump bar return instruction 4 3 Easy Scroll When active the Easy Scroll utility simplifies the menu selection process Instead of using the Thumb Pad to highlight an item and the Y a button to select it Easy Scroll lets you use only the Thumb Pad to highlight and select an item Using Easy Scroll changes typical navigation in the following ways e Theup b and down d arrows navigate menus The right c arrow works like the Y a button to confirm the selection of menu items The left e arrow works like the N X button for cancelling exiting and closing menus 29 Navigation 4 4 4 4 1 Screen Messages The Easy Scroll utility functions differently depending on the module For example in modules that have upper and lower toolbars the up b arrow cannot be used to navigate to the upper toolbar In this instance use either N X or the left e and right c arrows in a figure 8 pattern to move out of the lower toolbar Refer to Easy Scroll on page 94 for information on activating Easy Scroll Screen Messages The Vantage PRO unit displays three types of messages e Confirmation Messages e Warning Messages e Error Messages To manage on screen messages e Follow the instructions included with the message Confirmation Messa
95. ture leprity Eur 5 13 Sample test results 5 5 1 Changing Views The View button lets you change the way data displays P To change screen views 1 Select View The dropdown menu displays Figure 5 14 36 Component Test Operations Performing Tests Figure 5 14 Sample View menu 2 Selecta viewing option The screen changes to reflect your selection Figure 5 15 Figure 5 15 Sample RPM display 5 5 2 Pausing Data The Pause button Figure 5 16 stops data collection and lets you review data The screen can be paused at any time Figure 5 16 Sample Pause button P To pause test screen data 1 Select Pause Data is motionless on screen and some upper toolbar button functions change Figure 5 17 The Play button replaces the Pause button The Review button is selectable The Zoom button replaces the Snapshot button The Position Indicator displays in the Data Buffer Figure 5 17 Sample paused upper toolbar 1 Play button 2 Review button 3 Zoom button 4 Position Indicator 37 Component Test Operations Performing Tests P To release paused test data 5 5 3 9 9 4 e Select Play The data is moving on screen and toolbar controls return to their original functions Reviewing Data The Review button is used with the Thumb Pad to review paused data The Position Indicator Figure 5 17 displays the position of the current frame e Zero denotes the f
96. turn the grid on e Select Setup gt Grid A grid appears in the test area Figure 5 41 68 ETE Jesles ES Units f ignition System Trigger Display i Scaler Display EH Inverse Colors FS Save Data USZ0L ZETEC 02 12 m Figure 5 41 Grid sample screen Trigger Display Select Trigger Display to turn on the Trigger position values Figure 5 42 CI Units ignition System Grid a Trigger Display e Seales Display Eh Inverse Colors FS Save Data ed wiley For Trigger 32 004 1000000 FOCUS 20L ZETEC Figure 5 42 Sample Trigger values When Trigger Display is not selected trigger position values only display when the trigger position button is selected on the lower toolbar P To display trigger values e Select Setup gt Trigger Display The Trigger values display Figure 5 42 48 Component Test Operations Performing Tests Scales Display Select Scales Display to display the scale values on the graph P To turn Scales Display on e Select Setup gt Scales Display The scale values appear along the X horizontal and Y vertical axis of the graph Figure 5 43 O E Units lonition System TH Grid Trigger Display a Seales Display EH inverse Colors Gave Data Figure 5 43 Scales Display sample screen Inverse Colors Select Inverse Colors to change the color scheme P To change the color scheme e Select Setup gt Inverse Colors The color scheme changes Figu
97. up the printer e Connect a USB cable between your Vantage PRO unit and your printer See Figure 2 3 on page 5 for connection location e Refer to your printer s documentation for instructions on powering your printer and loading paper P To configure the Vantage PRO unit to print e Selecta printer manufacturer and port from the Utilities gt Tool Setup gt Printer dialog box See Printer on page 90 for details 3 6 Connecting to a Computer Connecting your Vantage PRO unit to a computer for file sharing requires the use of the optional ShopStream Connect software ShopStream Connect is a free software program that can be downloaded from the Internet at software snapon com 3 7 Powering Off the Unit The Power button Figure 2 2 on page 4 on the front of the unit powers the Vantage PRO unit off or puts it in Standby mode Standby mode conserves power while the unit is powered on but not in use For related information see e Power Management on page 88 e Emergency Restart on page 99 P To use the power options 1 Press the Power button The Turn off Vantage PRO dialog box displays Figure 3 6 22 Getting Started Powering Off the Unit 5 A Turn off Figure 3 6 Turn off Vantage PRO dialog box 2 Select either Standby or Turn off or press N X to cancel P To exit Standby mode e Press any button or the Thumb Pad 23 Navigation This section describes
98. ure data before and after a problem occurs while testing 40 Component Test Operations Performing Tests P To take a snapshot 1 Select Snapshot A dropdown menu displays Figure 5 24 Figure 5 24 Sample Snapshot menu 2 Select Manual The flash icon blinks Figure 5 25 indicating that Manual Snapshot mode is ready for use Figure 5 25 Sample Snapshot flash icon 3 Press Y a to take a snapshot The Collecting Snapshot message displays indicating that Snapshot data is being collected Figure 5 26 A N a A A Please wait Press W to abort Figure 5 26 Sample Collecting Snapshot confirmation message When the Snapshot finishes saving a final confirmation message displays Figure 5 27 Figure 5 27 Snapshot saved confirmation message When the confirmation message disappears you return to the test screen ready to take another snapshot 4 Stop using the snapshot by pressing N X NOTE O The saved snapshot can be retrieved from Saved Data Refer to Loading Saved Files on page 81 for details Changing Snapshot Settings You can set up a snapshot in the following ways e Adjust the percentage after trigger snapshots can be between 10 and 90 data captured after triggering e Save to different locations snapshots can be saved to CF1 CF2 or the USB port 41 Component Test Operations Performing Tests e Choose the file type select between bitmap and jpeg format for saving images
99. yn RO User Manual February 2011 ZEETM303D Rev B Trademarks Acknowledgements Snap on Scanner and Vantage PRO are trademarks of Snap on Incorporated All other marks are trademarks or registered trademarks of their respective holders Copyright Information 2011 Snap on Incorporated All rights reserved Disclaimer The information specifications and illustrations in this manual are based on the latest information available at the time of printing Snap on reserves the right to make changes at any time without notice Visit our website at http diagnostics snapon com North America snapondiag com Europe sun diagnostics com Europe For Technical Assistance CALL 1 800 424 7226 North America CALL 44 0 845 601 4736 United Kingdom E mail DiagnosticsUKproductsupport snapon com United Kingdom For technical assistance in all other markets contact your selling agent We EC DECLARATION OF CONFORMITY Snap on Diagnostics a division of Snap on UK Holdings Ltd Denney Road King s Lynn Norfolk PE30 4HG England declare under our sole responsibility for design and manufacture that the following product to which this declaration relates is in conformity with the following European Directives EMC Directive Product Model Applied Safety standard King s Lynn 23 07 2009 Document number te decl sod

User Manual - Snap-on

Contents

Download Pdf Manuals

Related Search

Related Contents