IRPTZ22 User Manual
Contents
1. J EXIT Move the cursor to IR LED and press iris open to submenu A1 Open Control Type Move the cursor to Open Control Type and press iris open to select IR light control type move the joystick to set IR light control type as External synchronization Auto Internal Synchronization Auto Time Schedule Open Close Instruction of five control types 1 External synchronization Auto Open or close of IR LED will depend on light sensor completely and dome will control the day night switch When the light sensor detected that the environmental light is lower than the threshold of IR LED open IR LED will turn on and camera switch from color to black white When the environmental light is higher than the threshold of IR LED close IR LED will turn off and camera switch from black white to color 2 Internal Synchronization Auto IR LED will turn on to the auto switch of camera from color to black white and turn off according to the light sensor control When the environmental light is higher than IR LED threshold value IR LED will turn off and D N of camera recover to auto 3 Time IR LED will turn on or offer according to the open and close time set by user 00 00 can be set in the time period For example Open time is set as 19 00 and close time as 06 00 then the IR LED will turn onat 19 00 closeat 06 00 in the next 20 morning 4 Open IR LED always 5 Close IR LED a2. 24 R23333229422257 Gray Video Black Video Green RS485 Blue RS485 DIP Switch bank is located on the side of the camera labeled as 180 cap 222 Low voltage Power Supply Applications Security Camera Pan Tilt platform Features v Operation 18 30 Input Output Isolated Efficiency 85 Input 24Vac 24V 60W Output Power 60VV Set point tolerance 2 Line Regulation 1 Load Regulation 1 Ripple And Noise lt 150mV pp Size 110mm 70mm 40mm 555 5 Mechanical Specifications Pin Description Dimensions are in millimeters mm 2 5 V 50 100 0 V 12 Vdc Output connector 02 Input Voltage in gt 18 30 V AC Output Power 60 W Voltage 12 18 Vdc Line regulation 1 Load Regulation 1 Efficiency 86 Chapter 2 Structure Side view Front view TIU L3 LET Chapter Dome Settings Dome protocol selection Dome address selection Protocol Setting This product supports two protocols PELCO P PELCO D and two baud rate 9600BPS 4800BPS 2400BPS Protocol dip switch is bit 1 3 of SW2 recon 5 1 8
3. D El Move joystick to preset position number and press iris on to setup mode Move joystick upward and downward to set number This dome supports 220 preset positions 1 64 100 255 32 gt B1 Title Setup Move cursor to title setup and press iris on to setup submenu to make preset position title setup C1 Call Move cursor to call and press iris on to call related preset position D1 Setup Press iris on to preset position setup mode and it shows Press iris on to confirm User can make operation to dome and press iris on to save current position E1 Delete Move cursor to delete and press iris on to related preset position B Auto Scan Operation setup Auto Scan Setup Preset Position Auto Scan Cruising Pattern Tour Sean 1 Tithe Setup Scan 1 Start Set lett boundary C Set right boundary Scan Speed 20 F Area Indication Auto Tracking Back Exit Bak A1 Scan Number Move the cursor to scan number and press iris on to setup mode Move joystick upward and downward to set scan number This dome supports 8 auto scans B1 Title Setup Move cursor to Title Setup and press iris on to enter scan title setup submenu to set the title C1 Start Scan 33 Move cursor to start scan and press iris to start related scan D1 Left Boundary Setup Move cursor to Set left boundary and press iris
4. Baud Rate Setting Baud rate setting dip switch is bit 4 5 of SW2 1 Lam 1 j 9 L3 o J 1 Dome Address Setting 8 bit dip switch SW1 at dome side is for setting dome address Dome setting adopts binary system the 8 bit is the highest the 1st bit is the lowest Total 255 dome addresses could be set Dome address code table under protocol PELCO P 2131153179733 Dome address code table under protocol PELCO D 1 1 j o 0 0 Notice 1 1 means status and 0 means off status 2 Dip switch for protocol PELCO P are the same while dip switch for PELCO D is slightly different PELCO D protocol supports maximum 254 dome addresses Chapter 4 Installation Guide 1 Take out the bracket and unscrew the power box from the bracket f f j a 1 2 Thread cables across the bracket and connect them to the circuit board in the power box Install the dome body to the bracket screw up with 4 inner hexagon screws If necessary apply water proof glue to the joint gap 3 unscrew the cover with the mark SET set communication protocol and addresses Screw up again with care to avoid water After the installation of dome body use two outer hexagon screws to tighten bracket and power box 4 Attach the drill positioning paste to the wall and drill according to
5. IR light setup Standby setup Privacy protection Clock setup Manual control boundary Password protection Dome title setup Other options Back Dome tithe setup Input information English capital ABCDEFGHII ELMWOPORS T OY Ways Canfirm Cancel Dome title setup ABCD EFGHI 1 KLMNOPORST LUV WAY Z s Confirm 25 Dome title setup Input information English capital abcdefghl kimnonpqrs t UvwXNVZ Confirm Cancel Dome title setup Input information D AL Humber 01234567859 Confirm Cancel Dome title setup E Input information Special Character 7 ce Contirm Cancel 26 Dome tithe setup Input information Chinese ABCD EFGHI J KLMNOPORST UVWXYZ t le 21 Confirm Cancel Input method instruction 1 Move the cursor to input information and press iris open to information edit mode Move the joystick left and rightward to move the cursor lt and press iris on to delete the character by the cursor and press iris off to exit edit mode 2 Move the cursor to input method option which is one line below Input Information and press iris on to input method setup mode Move the joystick upward and downward to chose the input methods which contain English Capital English lower case Chinese Number Special character 3 Move the cursor to one line below input method option and press iris on to character
6. Camera Setup Operation setup Reset Factory setup Help 1 Call upon preset 95 to open menu 2 Jaowstick up and down to control cursar to choose items 3 Press Iris Open to enter edit mode 4 Joystick up and down to edit tem parameters S Press Iris Open to confirm Iris Close to cancel Press Iris Open to check all the HELP information about the menu settings 41
7. the image would be breezing if changing scenes If the camera have to adjust the focus frequently in some special scenes that may cause breezing on the image it is recommended to use one push mode or zoom trigger mode One push mode is for preliminary adjustment zoom trigger for advanced adjustment Function description when zooming the camera will automatically focus clearly once zooming stopped the camera will fix the focus It is designed some special scenes with many illuminations that will force the camera to keep adjusting the focus and lead to unclear image 2 Day Nigh Disable the function of IR Led lights activate the D N function of the camera for special use 29 A Auto Focus Move the cursor to Auto Focus and press iris on to focus mode setup menu move the joystick upward and downward to select focus mode selection B Digital Zoom Move the cursor to Digital Zoom and press iris on to digital zoom switch setup Move the joystick upward and downward to switch on off digital zoom C Backlight Compensation Switch setup when the picture illumination is low open backlight compensation to higher it D Picture freeze Move the cursor to picture freeze and press iris on to picture freeze switch setup Move the joystick upward and downward to open or shut this function E Vertical Mirror Image Move the cursor to Vertical mirror image and press iris on to enter vertical image switch setup Move joystick
8. to setup mode it shows press iris on to confirm User can make operate dome to expected position and press iris on to save current position as left boundary E1 Right boundary setup Move the cursor to set right boundary and press iris on to enter setup mode it shows press iris on to confirm User can make operate dome to expected position and press iris on to save current position as right boundary F1 Scan speed Move cursor to scan Speed and press iris on to enter setup mode Move the joystick upward and downward to set the speed level as 1 30 C Sequence MOTION SEQUENCE lt PRESET gt SEQ NO 1 SCAN TITLE SEQ 1 SEQUENCE START Medias SEQUENCE SET eene AUTO TRACKING BACK EXIT A1 SEQ NO Move the cursor to SEQ NO and press the key IRIS ON key on control keyboard to enter the edition mode of sequence No move the joystick upward and downward to select number Then press IRIS ON to confirm B1 TITLE Move the cursor to TITLE and press IRIS ON to enter the edition mode of sequence title 34 C1 START MOVE the cursor to START and press IRIS ON to start the current sequence D1 lt SEQUENCE 5 Press IRIS ON to enter into the sequence setting SEQUENCE SEQUENCE SEQ NO 1 PRESET INTERVAL HILE SEQ 002 03 START 2 001 03 gt lt SEQUENCE SET ae 2 DELETE CC EDIT 01 003 BACK Move the curso
9. E1 Exposure mode Move the cursor to exposure mode and press iris to setup mode Move the joystick upward and downward to select parameters which can be set as Auot Manual Sutter priority iris priority Illumination priority Note For different cameras the mode options might be different F1 Shutter Speed Move the cursor to Shutter speed and press iris on to enter setup mode Move joystick upward and downward to set shutter speed value G1 Wide Dynamic Move the cursor to wide dynamic and press iris to enter setup mode 31 Move joystick upward and downward to select parameters as Low Moderate high Note For cameras without wide dynamic function this option setup is not available H1 Initiation Setup Move joystick to initiation setup and press iris on to recover camera parameters as default Operation Setup Main Menu Language Setup English System Setup Display setup Dame Setup Camera Setup Operation setup Reset Factory setup Help A Preset Operation setup EF Preset Position Auto Scan Cruising Pattern Tour Area Indication Auto Tracking Back Exit A1 Preset Position Number Operation Setup Preset Position Auto Scan Cruising Pattern Tour Area Indication Schedule operation Auto Tracking back Exit Preset Position Preset 001 Title Setup Preset 01 Call Setup Delete Back Exit Al
10. and 5 15 30 60 seconds option E1 Menu shut time With menu on menu will automatically shut after a period of vacant time Move the cursor to menu shut time and press iris on to setup mode move the joystick upward or downward to set time as 1 min 2 mins 5 mins 10 mins F1 Directi Zero Position Move the cursor to Direction Zero Setup and press iris on to direction zero position setup mode It shows press iris on to confirm and now you can control dome to zero position horizontally North press iris on to set this position as zero position 28 5 Menu Camera Setup Language Setup English System Setup Display setup EF Auto Focus On Digital Zoom Off Backlight Compensation off Picture Freeze Off Wertical mirror imagqe ott Come Setup camera Setup Operation setup Reset Factory setup Help Exit Zoom Speed Lowy Dmm gA T Advanced option Back Exit Camera Setup Auto Focus auto manual one push zoom trigger Digital Zoom off on BackLight Compensation Picture Freeze off on Vertical Mirror Image off on Zoom Speed low normal high Day Night auto day night Advance Option Back Exit Remarks Auto Focus includes 4 operating modes auto manual one push zoom trigger In auto mode the camera is running under auto focus condition it is recommended to use this mode for normal use In manual mode auto focus condition will be disable
11. best position Press Iris to confirm B DOME Press Iris to set DOME SETTING and move joystick to adjust DOME until get best position Press Iris on to confirm C ZONES Press Iris to set ZONES SETTING and move joystick to adjust ZONES until get best position Press Iris on to confirm D AUTO Press Iris to set AUTO SETTING and move joystick to adjust AUTO until get best position Press Iris on to confirm PAN TILT Press Iris to set PAN TILT SETTING and move joystick to adjust PAN TILT until get best position Press Iris to confirm DOME SETTINGS DOME SETTING MENU LAN GUAGE ENGLISH SYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS CAMERA STANDBY PRIVACY MASEK CLOCK MANUAL CONTROL PAS DOME TITLE OTHERS BACK EXIT MOTION RESTART FACTORY DEFAULTS HELP EXIT oO tm Son gt Call upon preset position 95 to enter the setting interface of the OSD menu and move joystick to DOME press Iris on enter submenu of DOME A IR LED SETTINGS DOME SETTINGS IR LED SETTINGS IR LED CONTROL OW Al EU MR ENVIRONMENT THRESHOLD VALUES 06 SEHSITIVITY 05 Cl CLOCK MANUAL CONTROL OPEN TIME 7 00 D PASSWORD CLOSE TIME 6 00 E ZOOM MATCH OFF F BACK ILLU MIHATOH OF LIGHT GROUP 1 10 irl EXIT ILLUMINATION OF LISHT GROUP 20 ILLUMINATION OF LIGHT GROUP
12. input mode Now selected character twinkles and move the joystick to select characters press iris on to input the twinkling character to the position of in the Input information block H Other Options Dome position Other options IR light setup A Standby setup Preset freeze Privacy protection Auto flip On i Clock setup Auto Stop Time 15 sec Dl Manual control boundary Be UCC Password protection E Dome title setup Zero position setup F Cp Other options Back Exit Back 27 Move the cursor to other options and press iris on its submenu A1 Temperature Control Mode Move the cursor to temperature control mode and press iris on to temperature control setup Use the joystick to select Cooling Auto Heating Off and press iris on to confirm input With IR LED on fans will be set as always on mode B1 Preset Freeze In calling preset setup menu move the cursor to Preset Freeze and press iris on to make setup Move the joystick to set On Off and press iris on to confirm C1 Auto Flip When dome rotates to 90 in vertical direction and the user wants to continue vertical rotation dome will automatically rotate by 180 horizontally in 2 seconds Press iris on to make this function as On off D1 Auto Pause time Auto pause time means the time period in which the dome does not receive any pause code and after that dome will pause automatically
13. other protective measures Keep power off until the completion of all installation e Do not dismantle parts Do not dismantle internal parts please turn to qualified maintenance professionals to carry out repairs e Do not put any object into the product Make sure that there is no metal object or flammable materials inside the product Such objects materials may lead to fire short circuit damage If water or liquid flow into the product turn off the power and disconnect the power cord immediately and then negotiate with the company Be careful to protect the camera Avoid the rain sea erosion e Keep the product away from electric or magnetic fields If the product is placed near TV radio transmitters electromagnetic devices electric motors transformers loudspeakers in the vicinity the electromagnetic fields generated by them would interfere the image e Do not point the camera at strong light Regardless of power on off status do not point the camera at the sun or very bright objects do not point the camera at bright stationary objects for a long time otherwise it will cause unrecoverable damage to the camera CCD e Maintenance with care It is advised to avoid collision or vibration Do not use strong or abrasive detergents to clean the dome body When cleaning up dirt use dry cloth if dirt is uneasy to remove swab with a neutral detergent If there is sticky dust on the lens please use the special len
14. the paste and install expansion bolts 5 Install the dome body together with bracket and power box to the expansion bolts and tighten with screws 6 Remove two screws from the power box and open it Thread power cable 220 through the water proof head on the left and RS485 and video cable through the water proof head on the right Connect cables to the circuit board double check order of connection to avoid damage from wrong connection After cable connection tighten the two heads if necessary appl water proof glue to the heads 7 close power box tighten the bracket to the power box Double check if there is joint gaps if necessary apply water proof glue Chapter 5 Functions Description 5 1 Features 1 Builtin Decoder e Power off protection no data loss e Support both Chinese and English menu e Support one week and eight hours each day timing operation e Exact time display e Builtin direction display function e 220 programmable presets e 8 cruising tracks each cruising track has 32 preset positions e 8 auto scan tracks the left and right boundaries an scan speed can be set e 8 privacy zones e 4 pattern tours each one with 180s memory e 3D location function e Guard location the dome can operate preset auto scan cruising and pattern tours functions after a short pause e Support PELCO PELCO D protocols e RS 485 bus e Remote reset function 2 Integrated Universal Speed Ch
15. ATTERN ZONES NO START STOP MOTIO 1 00 00 00 00 NONE 2 00 00 00 00 NONE 00 00 00 00 NONE 00 00 00 00 NONE Jm lt TIMING ACTION AUTO TRACKING 00 00 00 00 NONE 00 00 00 00 NONE 00 00 00 00 ONE 00 00 00 00 ONE OFF MON COPY BACK TIMING ACTION The user could set up the required functions during the designated time periods These functions include presets cruising track pattern tours and scanning Mover the cursor to the time duration to be set and press Iris Open to enter the setting mode Move the joystick Left Right to choose the option of exact time of Start Stop and Motion Move the joystick Up Down to edit the content and the press Iris On to confirm the operation A1 SCHEDULE NO The schedule of the timing action covers 7 days 1 week and 8 time periods 1 day B1 START C1 STOP D1 MOTION Timing action modes PRESET 1 8 SCAN 1 4 SEQUENCE 1 4 PATTERN 1 4 E1 ON OFF Press IRIS ON to enable or disable the timing action F1 COPY User can copy a schedule to other 6 days in a week G1 F1 38 G1 BACK Go back to upper menu Note The settings of each time periods can not overlaid and the time period can not be allowed to exceed 00 00 If the use tries to control the dome during the TIMING ACTION then the operation will be stopped and if there is no operation after 25 seconds then the dome will resume the timing action G AUTO TRACKING MOTIO
16. N AUTO TRACKING lt PRESET gt lt SCAN gt lt SEQUENCE gt lt PATTERN gt lt ZONES gt ENABLE OFF Cl lt TIMING ACTION gt amp lt AUTO TRACKING SENSITIVITY 06 AI FRAME RATE MID A1 SENSITIVITY Move the cursor to the option of SENSITIVITY and mover the joystick up and down to adjust the sensitivities Sensitivity of auto tracking funtion Scale from1 to 15 The smaller the value is the higher the sensitivity is B1 FRAME RATE Setting of the frame inspection rate LOW MID HIGH 39 C1 ENABLE Enabel or disable the auto tracking function Notice The auto tracking function is only for the speed dome with the camera module which supports auto tracking RESTART Main Menu Language Setup English System Setup Display setup Dome Setup Camera Setup Operation setup Reset Factor setup Help Press Iris Open to restart the dome FACTORY DEFAULTS Menu Language Setup English System Setup Display setup Dome Setup Camera Setup Operation setup Reset Factory setup Help Press Iris Open to resume all the setting to factory default settings 40 HELP Main Menu CAU SEN ZEN CES CUM SUCCES CONUM HAV SR OM Language Setup English system Setup Display setup Dome Setup
17. O CONFIRM will appear on the screen Move the joystick to do PTZ move and press IRIS ON to confirm E1 DELETE Move the cursor to DELETE and press IRIS ON to delete the current pattern 36 E lt ZONES gt MOTION ZONE IS NOT SET ZONE 1 TITLE NO ZONE 1 LEFT LIMIT RIGHT LIMIT DELETE lt PRESET gt lt SCAN gt lt SEQUENCE gt lt PATTERN gt Q ZONES TIMING ACTION AUTO TRACKING BACK EXIT A1 ZONE INFORMATION B1 ZONE NO Move the cursor to ZONE NO and press the key IRIS ON key on control keyboard to enter the edition mode of zone No move the joystick upward and downward to select number Then press IRIS ON to confirm C1 TITLE Move the cursor to TITLE and press IRIS ON to enter the edition mode of zone title D1 LEFT LIMIT Move the cursor to LEFT LIMIT and press IRIS ON to start setting the left limit of the current zone Then the sentence PRESS IRIS ON TO CONFIRM will appear on the screen Move the joystick and press IRIS ON to confirm E1 RIGHT LIMIT Move the cursor to RIGHT LIMIT and press IRIS ON to start setting the right limit of the current zone Then the sentence PRESS IRIS ON CONFIRM will appear on the screen Move the joystick and press IRIS ON to confirm F1 DELETE Press IRIS ON to delete the current zone 37 ACTION MOTION IMING ACTION SPRESEI SCAN SEQUENCE P
18. OSITION LANGUAGE ENGLISH BACK ST STEM INFORMATION DISPLAY SETUFP DOME SETTING 52 lt gt RESTART DOME SETTINGS FACTORY DEFAULTS IR LED gt HELP lt STANDBY gt EXIT lt CLODCKz PAS SOR DS DOME TITLE O THERS MANUAL CONTROL BACE EXIT MOTION E CAMERA SETTING us PRESET SANTO FOCUS FF 2 SCAN DIGITAL ZOOM OFF SEQUENCE BACKLUGHT OFF IMAGE FREEZE OFF FONES gt VERTICAL ON z TIMING ACTIONS ZOOM SPEED HIGH zAUTO TRACKING ADVANCED BAL kK Back EXIT Language It supports two language option Chinese and English Call upon preset position 95 to enter the setting interface of the OSD menu and move to language Setting push Iris to enter setting and move the joystick to switch Chinese English SYSTEM INFORMATION MAIN MENL eee eee SYSTEM INFORMATION Gom mesi mc mn OA ROAD UR RR Ra LANGUAGE ENGLISH DOME 10 0423458788 KP SYSTEM INFORMATIONS lt DISFLAY SETUP SETTINGS lt DTIDHN RESTART FACTORY DEFAULTS HELP EXIT ADDERSS 011 BAUDRATE 9600 8 1 PROTOCOL PELCOD SYSTEM PAL TEMP A DOME ID B DOME ADDRESS BAUDRATE D PROTOCAL E TV SYSTEM F INSIDE TEMP DISPLAY MENU DIS
19. PLAY LANGUAGE ENGLISH DOME ON A SYSTEM INFORMATION PRESET B DISPLAY SETUP AUTO ON C lt DOME SETTINGS ZONES ON D ME DATE TIME ON E PAN TILT F zDISPLAY POSITION G RESTART FACTORY DEFAULTS HELP BACK Call upon preset position 95 to enter the setting interface the OSD menu and move joystick select display enter submenu of display A DOME Press Iris on to set DOME SETTING and with ON OFF option B PRESET Press Iris to set PRESET SETTING and with ON OFF 2SEC 5SEC 10SEC option C AUTO Press Iris to set AUTO SETTING and with ON OFF 2SEC 5SEC 10SEC option D ZONES Press Iris to set ZONES SETTING and with ON OFF 2SEC 5SEC 10SEC option E DATE TIME Press Iris on to set DATE TIME SETTING and move joystick to select ON OFF 2SEC 5SEC 10SEC option F PAN TILT Press Iris to set PAN TILT SETTING and move joystick to select ON OFF 2SEC 5SEC 10SEC option Display position of setting contents on screen DISPLAY DOME ON PRESET OH AUTO ONES ON DATETIME DISPLAY POSITION DOME ONES AUTO FAN TILT PANH TILT DISPLAY POSITION BACK EXIT Move cursor to DISPLAY POSITION and press Iris on to enter submenu of DISPLAY POSITION A DATE TIME Press Iris to set DATE TIME SETTING and move joystick to adjust DATE TIME until get
20. SETTING and press Iris on to setup date Right left shift joystick to setup position and Upper and down shift joystick to setup increase and decrease of date Press Iris on to confirm B1 TIME SETTING Move cursor to TIME SETTING and others same with DATE SETTING Move cursor to SAVE SETTING and press Iris on to confirm If cancel current setting move cursor to BACK press Iris on back to the last submenu and cancel setting E MANUAL CONTROL DOME SETTINGS MANUAL CONTROL SETUP LEFT LIMIT Al SETUP FIGHT LIMIT Bl MANUAL CONTROL ON Cl STANDBY PRIVACY MASE CLOCK MANUAL CONTROL PASSWORD DOME TITLE OTHERS BACK A1 SETUP LEFT LIMIT Move cursor to LEFT LIMIT and press Iris on to setup B1 SETUP RIGHT LIMIT Move cursor to RIGHT LIMIT and press Iris to setup C1 MANUAL CONTROL Move cursor to MANUAL CONTROL and press Iris on to setup Move joystick to 24 select on off F PASSWORD SETTINGS A1 Modify Password Move cursor to Modify password and press iris open button to password modification mode Input old password first and the default password is 7111111 B1 Password protection Move the cursor to password protection and press iris open button to password switch setup move the joystick upward and downward to open or shut password protection When password protection is open input password before opening the menu G Dome Title Setup Dame position
21. ange Rotator e Delicate stepping motor stable sensitive and accurate e 360 continuous pan without blind area e Stepless speed change auto zoom speed matching e Auto overturn function e Manual Speed 0 01 120 s cruising speed 120 s 3 Built in High Definition Day Night Camera e Auto iris auto back light compensation e Auto manual white balance e Auto manual focus e Auto manual brightness control e Multiple kinds of camera for options OUL 4 All weather Outdoor Design e Built in heater e Built in fan can operate in 60 e High Die cast Aluminum Construction e P66 water proof e 3000V lightning and surge current proof 5 2 Function Instruction e Menu Function Support Chinese and English menu operation e Dome Address Setting Support up to 256 dome addresses and dome can be controlled by the order in same address The address can be set by the dial switch on decoder board e Privacy Protection Function Set black areas to mask the privacy or security parts The black areas location can be set and support up to 8 mask zones e Timing Running Function Users can set speed dome operation task at different time during one week Direction Indication Function Users can set North by themselves and also can set indication area When speed dome turns to the area the tilt will be displayed in screen e Motion Detection Function For some special cameras the dome can auto track the moving thing
22. e set 30sec 2min 5min 10min Press Iris to confirm STANDBY MOTION Move cursor to STANDBY MOTION and press Iris to setup motion move joystick and motion can be set preset 1 scan 1 crusing tour 1 pattern tour 1 no control Press Iris on to confirm C PRIVACY MASK STANDBY SETTINGS DOME SETTINGS PRIVACY MASK 1 A ENABLE OFF Bl 5 Cl CANCEL DI BACK EXIT STANDBY PRIVACY MASE CLOCK MANUAL CONTROL FASSWUO RD DOME TITLE OTHERS BACK A1 PRIVACY MASK Move cursor to PRIVACY MASK and press Iris to setup Move joystick to select privacy mask and it supports 8 masks in total B1 ENABLE Move cursor to ENABLE and press Iris on to setup switch of privacy mask Move joystick to select the state on and off C1 SETUP Move cursor to SETUP and press Iris on to setup the position of privacy mask press Iris on to confirm Move cursor to the privacy mask press Iris on to enter the privacy size setting and move joystick to adjust size Press Iris on to confirm D1 CANCEL Move cursor to CANCEL and press Iris to cancel selected privacy mask D CLOCK 23 DOME SETTING DATE TIME DATE 2008 01 01 A STANDBY i TIME 7 25 PRIVACY MASEK CLOCK MANUAL CONTROL PASSWORD DOME TITLE SAVE SETTING OTHERS BACK EXIT Move cursor to CLOCK and press Iris on to enter the submenu of CLOCK A1 DATE SETTING Move cursor to DATE
23. lways off Note D N AUTO of camera is valid unless the dome is set as Internal Synchronization Auto B1 Environment Threshold Value User can adjust the environment light threshold value as to different application locations In External synchronization Auto type default value is 1 2lux there may be slight difference because of the direction of IR LED IR LED is on in light condition Threshold value can be set from 1 to 10 1 means that the light is weak and 10 means that the light is strong C1 Sensitivity Setup When the IR LED is on environment light threshold to close IR LED delays 1 stands for high sensitivity and related delay range is narrow IR LED on and off may switch frequently in a certain light condition 10 stands for low sensitivity and related delay range is wide there is a huge light difference when IR LED on and off Default value is 5 D1 Open Time Press iris on to enter open time setup and move joystick leftward or rightward to select the time value you want to change and upward or downward to change the value E1 Close time Press Iris to set close time and move joystick from left and right to select clock bit move joystick from up and down to change value Note It is effective to set start time and close time of IR LED in the timing mode of IR LED control F1 Zoom match Press Iris on to set zoom match When select open illumination and power 21 of IR LED are matched with irradiation dis
24. r to EDIT and press IRIS ON to enter edition mode Move the joystick rightward and leftward to select item a When the is on the item NO move joystick upward and downward to select the NO of the preset in a sequence There are up to 32 presets in a single sequence b When the is on the item PRESET move the joystick upward and downward to select the preset NO you want to add in the sequence c When the is on the item INS move the joystick upward and downward to select edition mode as insert ok and delete d Press IRIS OFF to quit the edition E1 Delete Move cursor to delete press Iris On to delete related sequence 35 D PATTERN MOTION PATTERN lt PRESET gt gt PATTERN NO 1 1 lt 5 gt TITLE PATTERN 1 B1 SEQUENCE Peace C PATTERN 565 lt ZONES gt lt TIMING ACTION gt DELETE E1 lt AUTO TRACKING gt BACK EXIT A1 PATTERN NO Move the cursor to PATT and press the key IRIS ON key on control keyboard to enter the edition mode of sequence No move the joystick upward and downward to select number Then press IRIS to confirm B1 TITLE Move the cursor to TITLE and press IRIS ON to enter the edition mode of sequence title C1 START MOVE the cursor to START and press IRIS ON to start the current Pattern D1 SET Move the cursor to SET and press IRIS ON the enter pattern setting mode Then the sentence PRESS IRIS ON T
25. s e 3D Location Function In dome effective zoom scope can zoom in and out any area on screen also can move any point to center Need work with our Matrix or DVR e Focus Rotate Auto Match Speed Dome can auto adjust pan and tilt rotation speed depending on the focus distance e Auto Flip The lens can auto flip when it rotates 180 e Preset Position Setting and Calling Preset function means the speed dome can memory current pan tilt angel focus zoom ect When need it can be called upon directly Our speed dome Support up to 220 preset positions e Auto Scan Users can set the left and right boundaries by control keyboard Then speed dome can scan between it It can set up to 8 groups scan path e Auto Cruising Users can program some preset positions into auto cruising sequence then the speed dome can track as it Each cruising tracks has 32 preset positions e Pattern Tour Speed Dome can memory 180s running path or 500 orders When start pattern tour speed dome can track as recording path It supports 4 groups pattern tour e Guard Location The dome will rotate back to preset position after a period of vacant time e Lens Control 1 Zoom Control Users can control zoom by keyboard to get near or far images 2 Focus Control System auto focus default Also users can manually focus Note can manually focus by keyboard and matrix please refer to keyboard or matrix user s manual Camera can t a
26. s paper e Working Environment Power AC 220V 0 5A Communication port RS485 Environmental temperature 25 50 C 257 30 Moisture lt 95 Non condensing Atmospheric pressure 86 106KPa Note make sure outdoor installation meets water proof requirements Module Specifications Model IRPTZ22 Image Sensor 1 4 Sony Super HAD CCD Pixels 795 H x 596 V Resolution 540 TV Lines Video Output 1 0Vp p Composite Video 750 sync System Internal External V Lock Lens 3 4 7 7m auto focus Zoom 22X Optical 12X Digital FOCUS Auto Manual Infrared Range 350 ft 72 IR LEDs Minimum Illumination 0 1 Lux ICR On S N Ratio 5 Backlight Compensation Auto White Balance ATW Indoor Outdoor Manual AWB One Push WB Gain Auto Manual Pan Angle 360 continuous pan rotation Tilt Angle 90 auto flip Manual Speed pers Preset Soeed 120 s Communication Interface RS 485 Protocols Pelco P Pelco D Baud Rate 2400 4800 9600 bsp Mount Wall Mount Only Operating Temperature OA 22 a conu Dimensions Diam H 6 9 x 7 9 175rnm x 200mm Weight with without bracket 12 lbs 5 4kgs 16 lbs 7 3kgs Power Supply DC 12V 3A 4 b c 548 as rwn P 1i E DC12V 7
27. tance of camera With different zoom IR LED at its best control and adjust power automatically When select close start IR LED will depends on illumination set by user and it can t adjust automatically It is suggest selecting open zoom match G1 Illumination of light group 1 Light group 1 is outside lane long distance IR LED press Iris to set illumination value H1 Illumination of light group 2 Light group 2 is centre circle medium distance IR LED press Iris to set illumination value I1 Illumination of light group 3 Light group 3 is inside lane short distance IR LED press Iris on to set illumination value When close zoom match user should adjust irradiation distance by himself Note When open zoom match it can t adjust illumination of Light group 1 Light group 2 and Light group 3 manually B STANDBY SETTINGS DOME SETTINGS Umm UA DAR RA GS URNA GARS AUR GARA STAHDBY E STANDBY TIME 1MIH A STANDBY STANDBY MOTION CONTROL PRIVACY MASE CLOCK MANUAL CONTROL BACK PASSWORD DOME TITLE OTHERS BACK EXIT Move cursor to STANDBY SETTINGS and press Iris to submenu of STANDBY SETTINGS A1 STANDBY TIME Move cursor to STANDBY TIME and press Iris to setup time move 22 joystick and time can b
28. upward and downward to select on off F Zoom Speed Move the cursor to Zoom Speed and press iris to zoom speed setup mode Move joystick to select camera zoom speed which can be set as Low speed moderate speed and high speed G Advanced option Camera Setting Advanced Option Digital Zoom Off Backlight Compensation off Picture Freeze Off Wertical miror image ott Zoom Speed Lowy E White balance Auto A ain 208 B cain 167 C Illumination 01 Di Exposure mode anto El Adwanced option Shutter speed 00 Wide Dynamic COff LowhadsraterHigh Initiation setup Back Exit 30 A1 white balance mode Move the cursor to white balance mode and press iris to enter setup mode Move the joystick upward and downward as Auto Manual Indoor outdoor Note For different cameras the setup options might be different B1 R Gain Move the cursor to R gain and press iris on to setup mode Move joystick upward and downward to set the gain value Note Only if the white balance is set as manual setup is available C1 B gain Move the cursor to B gain and press iris on to setup mode Move the joystick upward and downward to set B gain value Note Only if white balance is set as manual setup is available D1 Illumination Move the cursor to illumination and press iris to enter setup mode Move the joystick upward or downward to set illumination value
29. uto focus in following situation e Target is not in the center e Can not guarantee clear images when watch near and far target at the same time e Target is light objects Such as neon lighting spotlights and other bright objects e Target is behind the glass with droplets and dust Target moves too fast e Large area targets such as walls e Target are too dark or inherently ambiguous 3 Auto Iris Control Auto sense ambient light and make quick adjustments 4 Auto Back Compensation In the bright background auto compensate light for the target and adjust the back light 5 Auto Manual White Balance Auto Manual adjust depending on the environment light changes 6 Day and Night Switch Only for Day Nigh Camera Speed dome camera can auto switch between color and black and white 7 High Speed Dome Menu Setup Only for camera with menu Call upon preset No 95 to enter into menu setup interface Press Focus to choose menu items and press Iris to set menu contents Chapter 6 Operation instruction The user can call upon preset position 95 to enter the setting interface of the OSD menu OSD Menu Tree SYSTEM INFORMATION DOMEID 0123456788 ADDRESS 00 1 BALDRATE 8500 8 1 PROTOCOL PELCO D TY SYSTEM PAL TEMP 40 1 BACK DISPLAY DOME OFF PRESET OFF AUTO OW ONES OFF DATETIME PAH TILT OFF 2S8EC AS SECH OSE DISPLAY P
30. v OPTIVIEW IRPTZ2 2 22X Zoom Infrared PTZ Camera CONTENTS Chapter Precautions 3 WCG D Chapter Dome Setting 7 4 Installation 10 Chapter 5 Functions Description eere 13 STR 13 CO UU CUO Mantas ete 14 Chapter 6 Operation instruction 18 Chapter 1 Precautions e Please read this manual carefully before installation e Handle with care In transportation and storage process we need to prevent stress such as severe vibration and immersion to avoid any damage to the product This product must be carried disassembled and packaged either in delivery to users or in return delivery to the factory for repairing Damage caused by assembled transportation will not be covered by warranty e Install with care Handle the product carefully and gently Prevent such incorrect operations as stress severe vibration or may lead to mechanical failure affecting the overall performance of product Under the cover are advanced optical devices avoid direct hand touch for the sake of image quality The electrical installation must comply with safety standards with use of dedicated power adapter Control signals and video signals should maintain a sufficient distance from high voltage equipment or cables in the transmission process if necessary take anti lightning anti surge and
Download Pdf Manuals
Related Search