Technical Notes - Matan Digital Printers
Contents
1. Crash Protector Sensor Figure 4 The Crash Protector Sensor 10100147 B O Matan Digital Printers Ltd Page 4 of 17 TAN Digital Printers 6 Power up the printer but do not turn on the PC or and open the Barak FE Application Raise the CARRIAGE to a safe height Manually move the carriage to the left over the PRINT TABLE until the mid point is located above the 273 hinge from the left as shown by the white broken line in the second figure below Figure 5 Manually Moving the Carriage Figure 6 The Print Table s Mid point 10100147 B O Matan Digital Printers Ltd Page 5 of 17 f ha TAN Digital Printers 9 Insert a 2 mm shim Figure 2 page 3 under each corner of the PRINT HEAD PLATE Figure 7 Inserting a shim Figure 8 Two shims inserted at front corners of the Print Head Plate 10100147 B O Matan Digital Printers Ltd Page 6 of 17 TAN Digital Printers 10 Lower the CARRIAGE using the MOTOR SWITCH as shown below until it just touches one or more of the shims in a way that you can still remove the shims without forcing them Figure 9 Lowering the Carriage using the Motor Switch 11 Remove the four shims from the PRINT TABLE 10100147 B Matan Digital Printers Ltd Page 7 of 17 Digital Printers 12 Using the FEELER GAUGE measure the gap between the PRINT HEAD PLATE and the PRINT TABLE on each of the four corners a2. Digital Printers TERE a a Jai CET STM Hin tg ag Sg a Aligning the Print Head Plate with the Print Table Technical Note 10100147 Rev B 10100147 B Matan Digital Printers Ltd Page 1 of 17 Digital Printers Safety Procedures Before reading this Technical Note please refer to the section on Safety Procedures in the Barak User s Manual About this Technical Note This technical note describes how to adjust the PRINT HEAD PLATE on the Barak printer Introduction To achieve optimized print quality and as part of the printer adjustment procedures the PRINT HEAD PLATE must be adjusted so that it is parallel with the PRINT TABLE Adjusting the Print Head Plate 1 Prepare a sheet of paper and draw a table as shown below Print Head Plate Height Table 2 a 4 J Gj 7 E 10 11 12 13 14 15 T 17 BL Back Lett BR Back Right FL Frond Le FR Front Right 10100147 B O Matan Digital Printers Ltd Page 2 of 17 TAN Digital Printers 2 The following tools must be prepared before proceeding e Feeler gauge 0 1 2 mm Figure 1 Feeler Gauges e Four 2 mm shims Figure 2 Shims 3 Shut down the printer 10100147 B O Matan Digital Printers Ltd Page 3 of 17 TAN Digital Printers 4 Disconnect the X MOTOR POWER and ENCODER CABLES as shown below Figure 3 X Motor and Encoder with disconnected cables 5 Remove the CRASH PROTECTOR SENSOR as shown below
3. CARRIAGE to a safe height 21 Manually bring the CARRIAGE over the middle point of the PRINT TABLE and insert the 2 mm shims under the four corners of the PRINT HEAD PLATE 10100147 B O Matan Digital Printers Ltd Page 11 of 17 is Digital Printers 22 Lower the CARRIAGE using the MOTOR SWITCH until it just touches one or more of the shims in a way that you can still remove the shim without forcing it Figure 13 The Carriage Height Gauge 10100147 B Matan Digital Printers Ltd Page 12 of 17 Digital Printers 24 Adjust the two CARRIAGE STOPPER SCREWS Figure 14 A Carriage Stopper Screw 25 Remove the four shims 26 Shut down the printer 10100147 B Matan Digital Printers Ltd Page 13 of 17 ATAN Digital Printers Crash Sensor 28 Manually return the CARRIAGE to the Home position without touching the LIMIT SWITCH 29 Reconnect the POWER and ENCODER X MOTOR CABLES as shown below 30 Power up the printer 10100147 B O Matan Digital Printers Ltd Page 14 of 17 TAN Digital Printers Appendix A Damage Report Form not for Print Head Details of faulty part Position in Company The Printer s Serial Number is displayed on the label located at the rear of the printer near the left end of the rollers as shown below 10100147 B Matan Digital Printers Ltd Page 15 of 17 Digital Printers e History bia 10000049 F Taylo
4. r Technical Writer 15 07 10 Gaby Cataloging B 10000049 F Taylor Technical Writer 08 02 11 Ronen Shalil 08 02 11 Updating O S E A G S NTT Head Office Matan Digital Printers Ltd 14 Amal Street Park Afek Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com U S Office Matan USA Inc 90 Earhart Drive Suite 4 Williamsville NY 14221 Tel 1 716 631 3770 Fax 1 716 631 3576 Email for customer support support matanprinters com Europe Office Matan EU C Rosalia de Castro 21 08025 Barcelona Spain Tel 34 902 932825 Fax 34 902 932826 Email for customer support support eu matanprinters com 10100147 B O Matan Digital Printers Ltd Page 16 of 17 TAN Digital Printers 10100147 B O Matan Digital Printers Ltd Page 17 of 17
5. s shown below Figure 10 Measuring the gap between the Print Head Plate and the Print Table 13 Write down the measurements on the table you have prepared 10100147 B O Matan Digital Printers Ltd Page 8 of 17 ALAN Digital Printers 14 Manually move the CARRIAGE so that the PRINT HEAD PLATE S mid point is located over the next hinge Figure 11 Manually moving the Carriage to the next Mid point 15 Repeat steps 11 12 and 13 until the PRINT HEAD PLATE S mid point is located over the last hinge 10100147 B O Matan Digital Printers Ltd Page 9 of 17 TAN Digital Printers Last Hinge Figure 12 The Carriage at the last hinge 16 At this stage carry out the final measurement only on the front and back left corners of the PRINT HEAD PLATE The right corners are no longer above the PRINT TABLE 17 Analyze the results from the table The tolerance between the different measurements between the hinges and the PRINT HEAD TABLE shouldn t exceed A 0 4 mm Meaning 0 2 mm along the entire PRINT TABLE 10100147 B O Matan Digital Printers Ltd Page 10 of 17 Digital Printers 18 Review the results on the table and decide which corners have to be adjusted by adding or removing shims between the CARRIAGE FRAME and the PRINT HEAD PLATE corners A Shim located at a corner 19 After adjusting the corners repeat the complete procedure until the results fall within the tolerance 20 Raise the
Download Pdf Manuals
Related Search