Quick Start Guide
Contents
1. l 1 iE i Auto Gontiguring E ise Slot 0 Slot 1 Slot 2 Slot 3 Dip Switch s TAPES 4 I O Unit Power connector I m USB port Slots LED indicators 2 Wire the 87Pn to power and PC IPower Supply 10 30 VDC GND VsS USB 87P4 0 USB port amp iVs E y PC COMX ed ites USB Connector Cable CA USB18 p 2 3 Configure CPU module Switch Label Setting Description ia Auto Config ON 4 Plug in the High Profile I O modules Example Plug in i 87019R to Slot 0 p s 8 019R is an Al Analog Input High Profile module High Profile Low Profile i 87019R is auto configured Baud Rate 115200 Checksum Disable Net Address 2 Note The Net Address of USB 87PN is always 1 After plugged in the slot indicator is flashing per 100 ms When software configuration is completed the LED becomes off If configuration is failed the LED is always on gt Software Configuration 1 Run DCON Utility to Search the USB 87Pn Ex USB 87P8 Note Please finish the Preparation P 1 before Software Configuration x Time Out Setting 500 ae Action view Help paud Hate Option amp 2 amp 7 115200 ICP L6G 57600 f 35400 f 19200 fw 3600 E ote a800 M 2400 f 1200 cee Disk drives a Display adapters l Select All Clear LAL DYDICD ROM drives 4 Floppy disk controllers 4 IDE ATA2. ATAPI controllers Protocol Option BRE csesicsamamese DCON ModbusRTU I Modbus ASCII 2 Mice and other pointing devices ig Monitors l m Network adapters l Y Ports COM amp LPT W Disable Enable ae Communications Pow ii Checksum Option Panty Option W None Even toa sand ase a Check Device Manager of your Cancel PC to see the connecting COM DCON UTILITY FER 452 The 140 Modules Found File COM Port Search Run Ae Help 0 End 25 Description 115200 Slot Auto Co Disable H S 7 lll Auto Contig Enable Fs 0 0 0 0 0 0 0 When the USB 87Pn is found click LL to stop the searching The X of X 0 0 0 means The configuration of that slot is not completed or not correct 2 Click USB 87Pn to setup slots configure Module 87P8 Hot Swap and Auto Configuration 170 Write To 87P8 Addr Hex Slot Configuratio Write To eT 0 Empty x 02 f Configure 4 Empty 03 00H OF Configure Empty 04 a ag aure Empty 05 If the status code is not 01H Empty 08 click Help button and follow the Empty 07 instruction please Empty 08 Empty 04 00H OF Copy Ceafigure save Configuration Load Configuration Load Configuration And Write To 87P8 Help J om JI A cw fa 3 Configure the 87K I O module Configuration for 7019R Module Yersion A201 Configuration Setting Channel Ena
3. Re US B 8 7P1 2 4 8 Quick Start 1 00 Original Writer Eva Li ICP DAS Co LTD www icpdas com Last Editor Eva Li 03 17 2008 Package Checklist Items Quantity Model No Description aw 37P1 Hardware module USB 87P2 USB 87Pn I O Unit SABON USB 87P4 P1 1 Slot P2 2 Slots USB 87P8 P4 4 Slots P8 8 Slots Cable 1 CA USB18 USB connector cable a oo Quick Start Mania soli manual 1 Software uty USB 87Pn User Manual EARNE Driver 2 4 mm Screw driver minus style Note USB 87Pn is only for High Profile l 87K I O modules please DO NOT use Low Profile I O modules For more information please refer to Chapter 2 2 5 amp Appendix B of USB 87P1 2 4 8 User Manual Preparation Power Supply 10V 30V DC Ex DP 665 htto www icodas com products Accessories oower supply oower list htm Install USB 87Pn Driverlnstaller to PC CD NAPDOS 87pn_io_unit USB 87Pn or ftp ftp icodas com pub cd 8000cd napdos 87pn_ io unit USB 87Pn e Install DCON Utility to PC Version 4 5 2 or above version Please remove the old version before install the new version CD Napdos Driver DCON_ Utility or ftp ftp icodas com pub cd 8000cd napdos driver dcon_utility p 1 Hardware Configuration 1 View of the USB 87Pn Power Module CPU Module High Profile i 87K I O Slots CPU Power 8 7Pn Power System ready lt n pea lca Enable Disable 7 a T i p DOG J 3 i A
4. ble Disable Setting Running 1 CH CIC Temp Offset Address dec Ae ae ponon a a _ _ M CH1 O OF T C K type v 0000 00 00 Foss a M CH 2 OF T C K type v 0000 0000 H a aa J CH 3 fepooooo FITC Kye 0000 eooo M CH Jeoo 000 OF T C Kepe eooo eooo M CHS feooooo0 IOF T CKtype x gt on eooo OF T C K type 00 00 H f 00 00 4 mmj OF T C B type 00 00 r 0000 Taj FOR EXAMPLE i 87019R Set data format ex Engineering and range ex T C K type as user s requirement ef 0 1 1c Setting T Configure only for auto configuration p 5 4 Click Write To 87Pn button Scanned I O on Slo to Configuration Slot Configuration Status After Write To 87Pn the Status Code is changed to OOH OK that means The configuration is correct 00H OK cop ee Contiqure 00H OF Copy Configure ad Configuration Load Configuration And rite To 8 P6 5 Click Start Search button Fi DCOHN UTILITY YER 452 The 40 Modules Found File COM Fot Search Run Ternmal Help 0 Auto Config Enable 0 0 0 0 of Slof 0 N81 Nat Disable Disable 115200 115200 10 2 Now the configuration is done 0 0 0 0 of Status means The I O configuration of each slot is correct Each plugged I O module will be listed under the USB 87Pn U
5. ser can click the name of I O module to watch its configuration Note 1 For changing the configuration of 87K I O module please repeat from the STEP 2 of the Software Configuration p 6 lt gt Change the hardware I O module User doesn t need to configure I O module again Remove the damaged sit anew one with the model number Easy Convenient S Technical Support l 3 USB 87P1 2 4 8 User Manual CD NAPDOS 87Pn_io_unit USB 87Pn_ or fto fto icodas com pub cd 8000cd napdos 87pn io unit usb 87pn DCON Utility User Manual CD Napdos Driver DCON_Utility Manual or fto fto icodas com pub cd 8000cd napdos driver dcon_utility manual I 87K high profile series I O modules selection guide http www icopdas com products PAC i 8000 8000 IO modules htm 4 Our service email account service icpdas com Our website www icopdas com p 7
Download Pdf Manuals
Related Search