User Manual - Continental
Contents
1. Danger to life from electric current Contact with live wires or components can lead to seri Ous injury or even death gt Only use the power adapter supplied otherwise the hand held tool could be damaged gt Doe not use the hand held tool if the connecting cable or the housing or the power adapter is dam aged Never open the housing of the power adapter Danger from electric shock if live connections are touched and or the electrical and mechanical con figuration is changed Never immerse the hand held tool or the mains plug into water or other liquids CPC hand held tool 11 ontinenfal Safety 2 3 Intended use The hand held tool is intended to be used only for checking and activating the tire sensors reading the pressure and temperature values E E m setting up the CPC system in the vehicle m error diagnosis and a updating the software Use for any other purpose is not considered as intended use Hazard from use for other than the intended pur pose If used for other than its intended purpose the hand held tool can be a source of danger and cause damage to equipment Use the hand held tool only for its intended purpose No claims of any kind will be accepted for damage resulting from use for other than the intended purpose In such cases the risk must be borne solely by the user 12 CPC hand held tool onfinental Technical Data 3 Technical Data Hand h2. O Tonm comyetoiin corans materai irat ane Olan CPC hand held tool 5 Commissioning 5 1 Checking contents and packaging As standard the hand held tool is supplied with the following compo nents m Hand held tool incl SD memory card 1 GB m Diagnosis cable USB cable m Power adapter m 4 power adapters for EU European Union UL USA UK England AU Australia CD ROM Brief instructions m Homologation certificate m 2 replacement fuses for the diagnosis cable Transport case gt Check for visible signs of damage or missing items on delivery Report an incomplete or damaged deliv ery to your supplier retailer immediately CPC hand held tool 21 ontinental Commissioning 5 2 Loading the hand held tool Remove the cover for the connection socket of the power adapter Connect the connecting cable of the power adapter and plug the power adapter into a mains socket Only use the power adapter supplied The rechargeable batteries are charged automatically when the power adapter is connected The hand held tool remains switched off during the charging process The charging process takes approx 5 hours For accreditation reasons the hand held tool may not be operated when the mains adapter is con nected 5 2 1 Charging state display m When the hand held tool is battery mode the charging state a battery symbol HR in the upper right corner of the s
3. PressureCheck The system for permanent tire pressure monitoring Tires Engineered in Germany Contents le Gre ie lial Bea ee ee er eran E des care 6 1 1 Information on this user MANUAL ccccecceeceeeeeeceeseeeseeeeeeeeteesaeeeeeseeeaeees 6 1 2 Liability disclaimer ccccccceceecceecseceeeceeseesaueaeeceeseeueccueceeteeseseseeseeseeees 6 1 3 GOD VEIT essen en nenn naar nn een een 6 1 4 ADA ee an ne Ea eee 1 5 Explanation of SyMDboIS ee ee een T 1 0 VANS a EEEE an 8 1 7 Manufacturer s address ee ne een 8 1 8 Waan Token nen Aa een nn ee ee een 9 1 9 AUCRSAC ESSEN u a rn en er nn euren 9 TIT EINAN OTO ner A 9 17 92 RDU ae nee E ee 9 L93 Updates a en een ee ee 9 hd ee ANI Vreden a ee ANA i ce te ae ee A 10 2 1 General safety INStrUCTIONS ccccccceccseeeeeeeeseeseeeceeeceeecueesaeesaeesanesaees 10 2 2 Ben SEK Hazard een ee 11 2 3 MARCOS SO een an En en En EEE 12 SCCA ANO a ee ee eee ere 13 4 2 DES CHIP APA oe eee rae re 14 41 Description of UNCON ee anecapsnesanecsiesencatndsacarboemataateuneyees 14 A2 Le 9 Bo 21g ea EA 15 4 2 1 Operating BIETE Aeneon 15 a URAT SIOC A ee eee ee ee 16 4 2 3 BGONNECLUON See een Tre ke 17 4 2 4 Slot for SD memory Ad er renpreeee 17 4 3 INIENU STELC U ee ne ea EA 18 4 4 Menu contro 0240280 00 00 nn nennen nun nn naaa anna ann nnn nenne nen nun nennen nun nen nennen 19 4 4 1 Calling a menu T
4. top position Read the sensor at the 6 o clock bottom position lf the sensor was successfully read at the 6 o clock bottom position Dismantle the tire Install anew sensor with a new rubber container Do not reuse the loose sensor and the old rubber container CPC hand held tool ontinental Operation Tire sensor Clear LOOSE state ENTER PASSWORD Use the arrow keys ei to select the numbers and letters for the password Press the Return key A to confirm selection select OK and press the Return key A to confirm when the password is complete If the correct password is entered the following message appears Sensor successfully reset CPC hand held tool 35 ontinental Operation 6 4 Initialization of the CPC system when reinstalling Before initializing the system make sure that all tire sensors are activated Initialization of the system takes place in 5 steps 1 Name of the vehicle 2 Selection of the vehicle configuration 3 Definition of axle specific characteristics 4 Coding the tire sensors 5 Transfer of the configuration to the CPC system Installation New installation Before starting with a new installation the charging state of the rechargeable batteries is checked If this is not sufficient the following message appears Rechargeable batteries too low Please charge it Charge the hand held tool as described in
5. Sensors can be checked activated deactivated or removed from the LOOSE state in the Tire sensor menu 6 3 1 Check Sensor Tire Sensor Check Sensor Read sensor as described in the section 6 2 Handling the hand held tool The following is displayed on the screen Check Sensor 1C28F787 CHECK 8 6bar 23 C D gt Activated Field Meaning ID hex Identification number of the sensor iiaa Pressure of the tire 0 bar in a dismantled condition TEMP Ambient temperature of the sensor STATE State of the sensor activated 9h Park mode Sensor is in idle state A telegram is trans mitted every 2 minutes deactivated 1h Shipping mode Sensor does not transmit telegrams DRIVE mode Dh Sensor is in motion A telegram is transmit ted every 2 minutes START mode 7h Beginning at a speed of approx 30 km h a telegram is transmitted 40 times very 16 seconds DRIVE mode follows CPC hand held tool Operation ntinental The following error messages are possible Error Meaning BRA The tire sensor Is NO longer operational Replace with a new sensor The capacity of the battery in the tire sensor LOW battery is no longer sufficient for continued use Replace with a new tire sensor Tire module may have loosened from the tire Senor iss see section 6 3 4 Clear LOOSE state ACCEL If this error occurs when the tire sensor is not in motion it is no long
6. existing INnSt all tlon iere seen 51 6 6 1 1 Checking the installation a 02H nn 52 6 0 1 2 Modily Parameter in sa daaa ee 52 6 6 1 3 Modify Sensor Dee 53 0 7 Danga a nee A A A 54 6 7 1 DTCs error COAES a ne 54 6 7 1 1 Read general error codes DTCS esen 55 6 7 1 2 Read tire relevant error codes DTCS 58 6 7 1 3 Erase all error codes DICS ccccsscceseeeeeeeeeeeeeeeees 61 6 7 2 Software updates sa aunnm nannten 62 Aa TION OS nennen ee 63 Aa O RR 64 Manna ee A AAA 66 7 1 Update software of the hand held tool ccceccecceeceeeeeeteeteeseeeeeeeaeees 66 7 2 Connection to the PC eecceeeeeeeeeteeeeeeteeeseeeeneeeeeeseseeseaeeauetseeeeesasenaes 67 7 3 Replacing the fuse in the diagnosis Cable ccccccsecceeeeeeceeeeeeeeeenees 69 14 SANG een ee ee me nee 70 I SON Are era ne on en een 70 82 310 UB ESNO E N Fee een ee 70 8 1 RR ii det E E 70 OMIDISBOSa Mr ee ae ae 71 9 1 Electrical electronic components u02402200200 0000 nnn nenn nenne nenn nennen 71 IOJEC Dee larallon or Sohle er 71 Eao E ene ee A eee eee ee ee eee eee 12 CPC hand held tool ontinental 4 1 1 1 2 1 3 General General Information on this user manual This user manual is part of the TPM O2 hand held tool and provides important instructions on the intended use safety startup and opera tion of the hand
7. following regulations apply for storage m Store at a dry place Maximum relative humidity 80 non condensing Protect from direct sunlight Keep storage temperature between 40 85 C After using store the hand held tool in the transport case supplied 8 Troubleshooting 8 1 Resetting lf the hand held tool should not longer react despite charged batter ies it must be reset To reset the hand held tool press in the reset key next to the connecting sockets with a ball point pen tip or the tip of straightened paper clip 70 CPC hand held tool Disposal ontinental 9 Disposal 9 1 XK Electrical electronic components This tool may not be disposed of in the domestic refuse within the European Union The tire hand held tool contains a lithium battery that is cast into the housing and cannot be replaced After reaching the end of its service life the tool must be disposed of in accordance with all current lo cal regional and national laws and regulations For this purpose it is necessary to return it to an authorized CPC sales or the central CPC collection point Address of the central CPC collection point Continental Trading GmbH Abteilung Entsorgung VDO StraBe 1 Gebaude B14 64832 Babenhausen Germany 10 EC Declaration of Conformity The full original declaration of conformity can be found on the CD CE Certificate_HHT_V01 pdf or at www contipressurecheck com CPC hand hel
8. for resetting the Sensor is LOOSE message The password can be requested from Continental Reifen Deutschland GmbH Infor mation can be obtained at www contipressurecheck com When CHECK SENSOR DISMANTLE TIRE appears in the CPC display or the Sensor is LOOSE appears in the hand held tool it is necessary to check whether the tire sensor m has been wrongly inserted in the rubber container m or has loosened in the tire To check proceed as follows First read out the DTCs error codes as described in section 6 7 1 2 Read tire relevant error codes DTCs lf DTC 19 is specified for the corresponding tire the tire sensor was inserted into the rubber container upside down Then proceed as follows Dismantle the tire Install anew sensor with a new rubber container Do not reuse the wrongly installed sensor and the old rubber container CPC hand held tool 33 ontinental 34 Operation lf DTC 1D is specified for the corresponding tire it is possible that the tire sensor in the tire is loose Then proceed as follows Read the sensor in a mounted state and mark the position where the sensor is received Move the marked position to the 12 o clock position top and reread lf the sensor was successfully read at the 12 o clock top position it is assured that the sensor is correctly fixed In this case the message can be reset lf the sensor cannot be read at the 12 o clock
9. loose inside See section 6 3 4 Clear LOOSE the tire state The TTM is mounted in wrong direction This error message is optional and not available in all CPC versions is a placeholder for the hex code that specifies the tire position This position is dependent on the selected configuration 60 CPC hand held tool i oa Operation onfinenfal 6 7 1 3 Erase all error codes DTCs The error messages of all components can be erased in the Erase all DTCs sub menu Diagnosis DTC error code Erase all DTCs The following message appears on the screen H XY 1 Do you want to erase all DTCs gt No Use the arrow keys to select Yes Press the Return key J to erase the error codes of all compo nents Finally the DTCs successfully erased or DTCs not completely erased message appears in this case repeat the deletion procedure CPC hand held tool 61 ontinental Operation 6 7 2 Software updates Diagnosis SW Update gt The CSW switching module component is only available for the trailer The charging state of the rechargeable batteries is checked before the software date starts If this is not sufficient the following message appears Rechargeable batteries too low Please charge Charge the hand held tool as described in section 5 2 Charging the hand held tool To ensure safe software updating do not switch off either the ha
10. manual Check cable between CCU and pressure control indicator Check pressure control indica tor with the hand held tool see installation manual If the diagnosis plug at the pressure control indicator remains open for 5 minutes without DTC interrogation this DTC 9FOB is activated 57 2 BER Continental Operation 6 7 1 2 Read tire relevant error codes DTCs Errors for a certain tire can be read in the Tire relevant DTCs menu item Diagnosis DTC error code Tire relevant DTCs The configuration appears on the screen as bird eye view The tire positions with error message are marked in black Tire related DTCs Ik Be Flashing black tire there is at least one active error for this tire gt Flashing black tire there is at least one passive er ror for this tire If there are no tire relevant DTCs The There are no tire relevant DTCs message is displayed t Use the arrow keys to select the desired tire The selected tire is marked with Press the Return key J to display the error 58 CPC hand held tool Operation ntinental Tire related DTCs BE 1404 ACT A 2 M 0 EaternalaRecAlvegs circuit pen sho t Error code 14 identifies the type of error 04 CPC internal coding of the tire position ACT active error error exists and must be eliminated MEM passive error error existed in the past and is no longer active A 2 ac
11. menu appears again Modify Sensor ID Modification Modify Installation Modify Sensor ID It is possible to make changes in the Modify Sensor ID menu item when the system setup remains the same and only the assignment of sensor IDs is necessary e g after several wheel changes or swap ping the tire positions For the procedure see section 6 3 4 Coding tire sensors CPC hand held tool 53 ntinental 6 6 7 1 54 Operation Diagnosis DTCs error codes Diagnosis DTC error code In the case of error messages there is a difference between global and tire relevant error messages First of all the connection to the CAN bus is checked lf there is no connection the message appears H XY 1 Check the CAN bus connection Check CAN bus communication to the components CCU dis play and CAN switch lf a connection exists a message appears containing the status infor mation of all components Connection state CCU Available DSP Available CSW Available Press the Return key A to call the DTC error messages sub menu DTC failure code Global DTCs Tire related DTCs Erase all DTCs CPC hand held tool Operation onfinenfal 6 7 1 1 Read general error codes DTCs Diagnosis DTC error code General DTCs General error codes can be read for the following components m CCU control unit a CSW switching module DSP display All
12. section 5 2 Charging the hand held tool 6 4 1 Enter a vehicle name VEHICLE NAME Use the arrow keys gt to select the numbers and letters for the password Press the Return key A to confirm selection Select OK and press the Return key A to confirm when the vehicle name is complete 36 CPC hand held tool Operation ontinental 6 4 2 Select vehicle configuration gt A list of the approved vehicle configurations and types can be viewed at www contipressurecheck com Characteristic Meaning Selection HGV bus Vehicle type Type of vehicle Add receiver Is an additional receiver Ves No installed The selection options are dependent on the Number of axles type of vehicle and the approved vehicle con figurations When selection is complete the birds eye view of a possible vehicle appears gt to scroll Use the arrow keys to scroll between the approved configura tions Press the Return key A to confirm selection CPC hand held tool 37 ontinental 38 Operation 6 4 2 1 Special case MARRIED Select this vehicle type when the tire sensors of the trailer are to be received and indicated in the display of the CPC system of the truck The sensors of the trailer are permanently programmed into the CCU of the truck for this purpose An additional receiver is necessary for this vehicle type and is there fore automatically linked into the CPC configur
13. SE STATS een 33 G 4 Initialization of the CPC system when reinstalling esen 36 6 4 1 Enter a vehicle NAME x sexs ee esen anakan aaneetesseechdteueneeeentvet 36 G 4 2 Select vehicle configuration nn of 6 4 2 1 Special case MARRIED 2 meneran naaa aaa 38 6 4 3 Define axle specific CharacteriStiCs ccccccseeseeeeeeeeeeeeeeseesees 39 6 4 3 1 Nominal pressure cccccecceeceeseeceeceeceecesceecesceecesansens 39 6 4 3 2 Lift AXIC 2x2 n en n an anna ana Kanan an nan nana na nn anna naa 39 6 4 4 Coding tire SeNSOrS xssesseesana a ea 41 6 4 5 Transfer the configuration to the CPC system 43 6 4 6 Possible ProDleMs cccceccsecseseeceeceeceeceeseeceecerceecesceearceecasases 45 6 4 6 1 Sensor not found after 2 atteMpIiS nennen 45 6 4 6 2 2 Different sensors found simultaneously 46 6 4 6 3 Sensors not ACIVALC Gi icccsnssnnctscedvnedunccdecantdeneandenscentuanendt 47 6 4 6 4 Transfer of configuration aborted 48 6 4 6 5 Transferred configuration not accepted 49 4 CPC hand held tool 6 5 Resume IIANZ QUOM nennen 50 6 5 6 1 Identification number does not belong to vehicle 50 6 5 6 2 Identification number does not belong to vehicle 50 8 5 Modilyinstal alone naaa A AA ENNEN ETENN 51 6 6 1 Modify
14. ard 23 SOl 2 ea waa sea an nenne 17 Storage 70 Symbols 7 T Technical data 13 Type plate 20 W WAarninQS 8 Warranty 9 CPC hand held tool ontinental 73 Continental Reifen Deutschland GmbH B ttnerstra e 25 30165 Hannover Germany www contipressurecheck com www continental truck tires com www continental corporation com BH_HHT_0413_A1_EN US
15. ation by the hand held tool The trailer must be permanently married to the truck otherwise NO RECEPTION is displayed in the display for the trailer sensors see Display in the user manual For the MARRIED vehicle type the number of axles for the respec tive truck and trailer is selected separately Altogether it is not possible to select more than 6 axles H XY 1 Number of Axles gt 3 TRUCK BUS 2 TRAILER Use the arrow keys oe to change selection Press the Return key A to confirm selection CPC hand held tool 7i Ga Operation ntfinental 6 4 3 Define axle specific characteristics 6 4 3 1 Nominal pressure Use the arrow keys to navigate between the axles Use the arrow keys H to set the required nominal pressure Press the Return key A to confirm the set nominal pressure The nominal pressure can be set between 4 5 bar 65 psi and 10 bar 145 psi gt When determining the nominal pressure consider the instructions from the tire manufacturer 6 4 3 2 Lift axle Depending on the vehicle type an axle can also be defined as a lift axle Use the arrow keys to navigate between the axles Use the arrow keys to change the state y Lift axle no lift axle Press the Return key J to confirm selection CPC hand held tool 39 ontinental Operation General conditions m If the selected configuration only has 2 axles a truck or drawbar
16. ation with the CCU is successful the following menu items appear m Check Installation m Modify Parameter m Modify Sensor ID CPC hand held tool 51 ontinental Operation 6 6 1 1 Checking the installation 6 6 1 2 52 Modification Modify Installation Check Installation The parameters of the existing installation are displayed under the Check Installation menu item No changes can be made Press the Return key to call the following information A successively Vehicle type State Add Receiver Nominal pressures State lift axles Following the lift axle overview the Modify Installation sub menu appears Modify Parameter Modification Modify Installation Modify Parameter The following parameters can be changed in the Modify Parameter menu item Add Receiver Yes No m Lift axle Yes No m Nominal pressure After the parameters are changed they can be transferred to the CCU The following messages appear H XY 1 CONFIGURATION COMPLETED CONNECT TOOL WITH DISPLAY IGNITION ON START UPLOAD CPC hand held tool Operation 6 6 1 3 ontinentfal Press the Return key A to start uploading H XY 1 Upload in progress Please wait lf data transfer is not successful proceed as described in section 6 4 6 4 Transfer of the configuration interrupted or in section 6 4 6 5 Transferred configuration not accepted Otherwise the Modify installation sub
17. ayed Code all tires as specified on the screen The following message ap pears for the last tire to be coded to proceed After the coding procedure is complete for every tire the process is continued with transfer of the configuration to the CPC system To code the tire sensor of the inner twin tires the tool can remain on the the outer of twin tires 42 CPC hand held tool Operation ntinental 6 4 5 Transfer the configuration to the CPC system In order for the data to be transferred to the CPC system the hand held tool must be connected to the CPC system via the diagnosis cable The following message appears on the screen of the hand held tool H XY 1 CONFIGURATION COMPLETED CONNECT TOOL WITH DISPLAY IGNITION ON START UPLOAD To ensure safe transfer of the configuration do not switch off the hand held tool during data transfer or interrupt data transfer In the worst case the CPC components CCU DSP CSW could lose their con figuration To transfer the configuration for a truck bus proceed as follows Connect the hand held tool to the plug socket of the display via the diagnosis cable Switch on the ignition Press the Return key J to start the transfer To transfer the configuration for a trailer proceed as follows Release the plug connection between the pressure control indi cator and the trailer wiring harness Connect the hand held tool to the
18. creen is displayed The level indicated on the battery symbol corresponds to the charging state of the recharge able batteries Ho Ifthe hand held tool is connected via the power adapter a plug symbol appears in the upper right corner of the screen 22 CPC hand held tool Cntinental Commissioning 5 3 Changing the memory card The files required for updating the firmware of the display CCU and the switching module CSW are stored on the SD memory card built into the hand held tool An SD memory card is supplied with the hand held tool by default gt To update the firmware the hand held tool is con nected to the PC Laptop via the USB cable see section 7 2 Connecting the the PC The SD memory card remains in the hand held tool 17340230000 Continental A2C81336600 Handheld tool www contipressurecheck com Made in Italy Err In lEKTANAD IN To replace the SD memory card if it is defective proceed as follows Unscrew the fixing screw H of the cover amp and remove it Change the memory card Pay attention to proper location of the contacts when inserting Replace cover D and tighten the screw CPC hand held tool 23 ontinental 9 4 24 Commissioning Switching the hand held tool ON OFF Press the ON OFF key to switch the hand held tool Q on and off The start screen is displayed for 3 seconds after switching on ee iPressureCheck by CONTINENTAL The followi
19. d tool 71 ontinental 11 Index A Abbreviations After sales service Eliminating errors Repairs Updates C Charging state Cleaning Commissioning Charge tool Set up tool Switch tool ON OFF ConnectionS D Declaration of conformity Description of function Disposal mus a sn ann kn ones Intended use L Liability disclaimer M Manufacturer s address Menu control Index Menus Diagnosis DTCS 54 Software Update 62 Installation Continue Installation 50 New Installation 36 Modification Modify Parameter 52 Modify Sensor ID 53 Check installation 52 Tire SeNSOr 29 Activate Sensor 31 Check Sensor 30 Clear LOOSE state 33 Deactivate Sensor 32 Menu structure 18 O Operating elements 15 Operation Code sensor 28 Handling the tool 26 Read sensor 27 Update tool software 66 R Replace the fuse in the diagnosis cable 69 Reset 70 CPC hand held tool Index S Safely sea 10 Scope of supply 21 SD memory card Change c
20. e screen H XY 1 DOES IDENTIFICATION BELONG TO THIS VEHICLE gt Not Available 6 5 6 1 Identification number does not belong to vehicle Use the arrow keys to select Yes and press the Return key A to confirm the vehicle name The initialization process is then continued from the point where New Installation was interrupted I The coding process of the tire sensors is an excep tion If coding is not fully completed begin with the first tire again 6 5 6 2 Identification number does not belong to vehicle Use the arrow keys to select No and press the Return key to confirm in order to exit the menu item otherwise the wrong configuration is installed in this vehicle Run anew installation for this vehicle see section 6 4 Initializa tion of the system for new installation CPC hand held tool onfinental Operation 6 6 Modify installation gt Before starting with modification the charging state of the rechargeable batteries is checked If this is not sufficient the following message appears Rechargeable batteries too low Please charge it Charge the hand held tool as described in section 5 2 Charging the hand held tool 6 6 1 Modify existing installation The hand held tool must be connected to the CCU gt If communication is not possible the procedure is aborted and a corresponding message appears Modification Modify Installation If communic
21. eld tool Dimensions L x W x H 160 x 90 x 38 mm Weight 7390 Q 3 inch 128 x 64 pixel Display monochrome graphic LCD with backlighting Degree of protection IP 54 Sonya padi Lithium ion rechargeable battery 850 mAh 11 1 V Operating temperature 10 to 50 C Storage temperature 40 to 85 C USB 2 0 PC Type A Diagnosis cable Hirose 24 pole Barrel connector 1 3 3 5 mm ower adapter connection CHC O Card type SD card max Capacity 2 GB High frequency part HF frequency range 433 92 MHz LF frequency range 125 KHz Number of plugging cycles min USB plug 1 000 Diagnosis plug 100 cycles Power adapter plug 10 000 Type Sinpro SPU 15 Input 90 264 VAC 47 63 Hz Output 13 V 16 V max 1 15 A 0 94 A CPC hand held tool 13 ontinentfal 14 Description 4 Description 4 1 Description of function The TPM O2 hand held tool is a programming tool with the following functions Tire sensor check Tire pressure and temperature measuring Tire sensor activation deactivation Error message resetting New installation on the vehicle trailer Checking and changing the existing configuration Reading of error codes DTCs Updating firmware for the display DSP CCU and switching module CSW CPC hand held tool Description nfinenfal Tool overview Operating elements Made by TECHNOMOTOR Designation Function Pos Exiting a sub menu 2 ESC key Canceling a
22. er operational and must be replaced by a new one gt If the CHECKING is displayed on a black back ground press the Return key A to repeat the checking procedure 6 3 2 Activate sensor When shipped the sensor is deactivated 1h and does not transmit telegrams In order to operate the sensor in the vehicle activation is necessary Tire sensor Activate sensor Read sensor as described in the section 6 1 Handling the hand held tool The following is displayed on the screen Sensor successfully activated CPC hand held tool 31 ontinental 32 6 3 3 Operation The following messages appears after 3 seconds Activate Sensor BE ID Hex 1C28F787 aa gt Activated 9h Deactivate sensor The sensor must be deactivated for longer periods of storage or for shipping Tire sensor Deactivate sensor Read sensor as described in the section 6 1 Handling the hand held tool The following is displayed on the screen Sensor successfully deactivated The following messages appears after 3 seconds Deativate Sensor ID Hex 1C28F787 8 6bar D gt 23 C Deactivated 1h If the sensor is in a deactivated state 1h it is in shipping mode and no longer transmits telegrams The tire sensor must be deactivated for transport in an airplane CPC hand held tool Operation onfinenfal a 6 3 4 Clear LOOSE state A password is necessary
23. errors are listed Use the arrow keys ki to view all listed messages CCU Global DTCs as Ocl2 MEM A 112 M 32 EvternalARecAivers circuit pen short Error code ACT active error error exists and must be eliminated MEM passive error error existed in the past and is no longer active A 112 if M 0 ACT active for 112 ignition cycles if M gt 0 MEM was was active for 112 ignition cycles until eliminated M 32 passive for 32 ignition cycles CPC hand held tool 55 ontinental Operation The following error codes are possible Display of error codes is always in English irrespec tive of the selected operating language For the CCU DTC Description Remedy 9C01 HS CAN transmit re Check plug connector to an dis ceive error bus off play and CCU check cable 9010 Communication Error Check plug connector to addi with Add Receiver tional receiver check cable Communication Error with Add Receiver Line is open short Check whether on board voltage 9A01 Supply voltage too low er rere sy Check whether on board voltage is max 28 V Check plug connector to addi tional receiver check cable 9A02 Supply voltage too high Change location indication of radio interference 9B02 RAM ROM EEPROM Replace CCU failure 9B03 Micro controller failure Replace CCU Use the hand held tool to check whether tire sensors are really installed For th
24. g appears Other sensors in range Move sensor and check again Remedy Put the sensor out of range of the other sensors or sources of interference 6 2 2 Coding a sensor fitted in the tire When coding the tire sensors the following is displayed In the animation the marker point moves along the side wall in a specified direction and at a specified speed 28 CPC hand held tool Operation onfinenfal i Hold the hand held tool with antenna amp at the side wall of the tire as illustrated The marker point is the starting point Move the hand held tool along the side wall of the tire according to the speed of the animation The hand held tool transmits the interrogation signals at 3 transmis sion power levels The levels are represented on the screen The hand held tool is moved along the side wall of the tire cir cumference for each power level I gt The g symbol is perpendicular to the side wall and the antenna guided beneath the tread Pay attention to the location of the starting point and the direction of rotation in the animation 6 2 2 1 Problem when coding 2 different sensors lf the hand held tool reaches 2 different sensors the following mes sage appears MORE THAN ONE SENSOR RECEIVED MOVE TOOL WITH SPEED SHOWN IN ANIMATION Repeat the coding procedure for this tire CPC hand held tool 29 ntinenfal 30 6 3 Tire Sensor menu Operation
25. he normal household waste CPC hand held tool 7 ntinenfal General 1 6 Warnings In the current user manual the following warnings are used A warning of this hazard level indicates a hazardous situation lf the hazardous situation is not avoided it can result in serious injuries gt Follow the instructions in this warning to avoid seri Ous injuries to persons ATTENTION A warning of this hazard level indicates potential damage to equipment lf the situation is not avoided it can result in equipment damage gt Follow the instructions in this warning to avoid the equipment damage A note draws attention to additional information of importance for the further work or which simplifies the work step described 1 7 Manufacturer s address Continental Reifen Deutschland GmbH ButtnerstraBe 25 30165 Hannover Germany www contipressurecheck com 8 CPC hand held tool General 1 8 1 9 1 9 1 1 9 2 1 9 3 ontinental Warranty terms The statutory warranty terms apply with the exception of possible contractual agreements The current version can be obtained from www contipressurecheck com After sales service Eliminating errors gt If the handling instructions in this user manual do not lead to the elimination of the fault contact the after sales service of the respective country All necessary information can be obtained from www contipressurec
26. heck com Repairs In the event of repair of the hand held tool a used replacement tool will be made available This generally takes place within 24 hours of receiving the defective tool but no later than 72 hours Calculation of the costs of replacement takes place according to the relevant regulations of the warranty see section 1 8 warranty regula tions Updates The current version of this user manual and further information can be obtained from www contipressurecheck com CPC hand held tool 9 ontinenfal 10 2 Safety Safety 2 1 General safety instructions Observe the following general safety instructions to ensure safe han dling of the hand held tool Check all parts of the hand held tool for visible damage before use Do not use a damaged hand held tool Do not allow the hand held tool to fall down or subject it to hard knocks With the exception of the slot for the SD memory card do not open the hand held tool There are no maintenance relevant parts inside the hand held tool The rechargeable battery of the hand held tool can not be replaced Only allow the manufacturer to repair the hand held tool Improper repairs or opening the tool will invalidate the guarantee Protect the hand held tool against humidity or penetration of liquids or objects If the tool comes into contact with liquids disconnect it from the power supply immediately CPC hand held tool 2 2 Electric shock hazard
27. held tool The user manual must be read and utilized by every person who oper ates this hand held tool and troubleshoots the hand held tool Store the user manual and give it the any new owner together with the hand held tool Liability disclaimer The manufacturer assumes no liability for damage and operational faults resulting from failure to observe this user manual use for other than the intended purpose improper repairs unauthorized modifications or use of non approved spare parts Copyright This user manual is copyrighted This user manual may not be duplicated or made accessible to third parties in particular competing companies without express approval from Continental Reifen Deutschland GmbH CPC hand held tool General ontinental 1 4 Abbreviations The following abbreviations are used in this user manual Abbreviation Meaning Central Control Unit ContiPressureCheck ecu ore sw CAN Switch switching module integrated into the CCU trailer a ore pessoa O Bu 1 5 Explanation of symbols Warnings in this user manual are also indicated by warning symbols The following warning symbols are used in this user manual Symbol Meaning General warning Warning of electric current General instructions and useful suggestions on handling Note on observing environmental regulations 9 for disposal Electric electronic components with this symbol may not be disposed of in t
28. ion aborted If transfer of the configuration was not successful the following mes sage appears H XY 1 Check the CAN bus connection Remedy 1 Check the connection between the hand held tool the diagnosis cable and the CPC components 2 Inthe case of a truck installation check that the ignition is switched on 3 Repeat transfer of the configuration 4 lf transfer is aborted again exit the menu and check the CAN communication with the CCU For this purpose read the DTCs as described in section 6 7 1 DTCs error codes gt If the CAN communication is working repeat transfer of the configuration one more time See section 6 5 Resume initial ization gt If the CAN communication does not work check the cabling of the CPC system 48 CPC hand held tool Operation ontinental 6 4 6 5 Transferred configuration not accepted lf configuration of the system is not successful the following message appears H XY 1 Error Uploading Refer to manual Remedy In this case communication to the CCU has failed 1 Check all plug in connections 2 In the case of a truck bus switch on the ignition 3 Repeat the upload procedure CPC hand held tool 49 ontinental 90 Operation 6 5 Resume initialization The Resume installation menu item is only active when the New installation procedure was interrupted Installation Resume installation The following message appears on th
29. ipped with an antenna The following describes the procedure for communication that is used tn all menus Always hold the antenna in the direction of the sen sor in order to ensure the best possible communica tion If sound and or vibration was switched during setup a corresponding signal is emitted after successful reading The read operation takes place via 3 steps with increasing transmission power If communication beyond that is still not possible the process is can celed 26 CPC hand held tool Operation onfinenfal 6 2 1 Reading an accessible sensor In the event that the sensor is easily accessible proceed as follows for reading Hold the hand held tool with antenna 2 directed to the sensor as illustrated 6 2 1 1 Problem when reading communication failed If communication with the sensor is not possible the following mes sage appears Communication failed Refer to manual Remedy 1 Check the charging state of the hand held tool and charge if necessary 2 Repeat the procedure with another tire sensor If communication is possible the 1st tire sensor is defective If communication is still not possible contact after sales service CPC hand held tool 27 PERS Gntinenfal Operation 6 2 1 2 Problem when reading other sensor in range If a further sensor is within radio range the sensor to be checked can not be safely read The followin
30. is purpose per form coding procedure accord ing to section 6 4 4 Coding tire sensors RF Jamming No TTMs mounted Configure CPC system accord ing to section 6 4 Initializa tion of the CPC system when reinstalling No configuration stored For the display DTC Description 9B04 EEPROM Defective Replace display 56 CPC hand held tool Operation For the switching module CSW DTC Description ontinental Remedy 9F02 PAN ROM EEPROM Replace CCU failure HS CAN communication Se failed Check plug connector to CCU check cable between CCU and pressure control indicator 9F04 On board power supply Check whether on board volt below threshold age is at least 12 V 9F05 On board power supply Check whether on board volt above threshold age is max 28 V 9F06 Power supply for CPC Check whether on board volt ECU below threshold age is at least 12 V 9F07 Power supply for CPC Check whether on board volt ECU above threshold age is max 28 V 9FOA Warning lamp short circuit 9FOB Warning lamp open circuit CPC hand held tool 9F08 Power supply additional Check whether on board volt receiver below threshold age is at least 12 V 9F09 Power supply additional receiver above threshold Check whether on board volt age is max 28 V Check cable between CCU and pressure control indicator Check pressure control indica tor with the hand held tool see installation
31. n action Scrolling back in some menus t Navigating within a menu Arrow keys Setup values oO MM Confirming selection Return key Acknowledging a message ON OFF key Switching the hand held tool on off atema d Antenna for responding to the tire sensors CPC hand held tool 15 ntinental 16 Description 4 2 2 Underside 7 7 S rr He Pos Designation Fixing for carrying strap not included in the scope of supply CPC hand held tool ontinental Description 4 2 3 Connections J Et NW wi i Designation Pos O comeston roneo Oe man 4 2 4 Slot for SD memory card 17340230000 Continental A2C81336600 Handheld tool www contipressurecheck com Made in Italy Designation C Cover for SD memory card slot o Fixing screw for cover CPC hand held tool 17 onfinental Description 4 3 Menu structure Tire Sensor Check Sensor Activate Sensor Deactivate Sensor Clear LOOSE Status Installation New Installation Resume Installation Modification Modify Installation Check Installation Modify Parameters Modify Sensor IDs Diagnosis DTC failure code General DTCs Tire related DTCs Erase all DTCs SW update CCU control unit DSP display CSW switching module integrated into the CCU trailer Connection to the PC Setup Language German French English Polish Turkish Unit P
32. nd held tool during data transfer or interrupt data transfer There is a risk that the com ponents to be updated CCU DSP CSW could be damaged permanently A software update is possible for the following components m CCU control unit a CSW switching module DSP display 62 CPC hand held tool Operation onfinenfal 6 7 2 1 HGV bus To update the software for a truck bus proceed as follows Connect the hand held tool to the plug socket of the display via the diagnosis cable Switch on the ignition If anew software version is available on the hand held tool the fol lowing message is displayed Software Update Ss CCU VER 01 05 DSP VER 01 12 NEW VERSION 01 13 CSW PRESS TO UPDATE Software Update CCU VER 01 06 DSP VER 01 12 NEW VERSION 01 13 CSW PRESS e TO UPDATE Press the Return key J to start software transfer for the display lf the software for the components was updated successfully the fol lowing message appears Software Update VER 01 06 VER 01 13 CCU CCU UP TO DATE DSP DSP UP TO DATE CSW CPC hand held tool 63 ontinental 64 Operation 6 7 2 2 Trailer To update the software for a trailer proceed as follows Release the plug connection between the pressure control indi cator and the trailer wiring harness Connect the hand held tool to the wiring harness via the diagno sis cable Switch on the igni
33. nelioNn nnneeneen 19 4 4 2 Changing a SCICCT OM inssnssivnuricnsdentncsuieoswevatedsneoiseesaceaiesiertessesenseec 19 4 43 STOSO een er 19 49 TYDS Deere en Eee 20 CPC hand held tool ontinental Table of Contents SAC Om SIONN ee aeeese eee ieee 21 5 1 Checking contents and PaCKAGING cscccscecseeceeeceeeceeeceeeseeeseeeseeesaeess 21 5 2 Loading the hand held tool essen petnedieehidronceese nines 22 521 Charging State ASplay ee ee 22 5 3 Changing the memory Are 23 5 4 Switching the hand held tool ON Off ccccccsecceseeceeeceeeeeeeseeeeseeeeees 24 5 5 Setting up the hand held tool cccscccseecseeceeeceneceetccasceasseessensseaees 25 Seeron AAA tr AAA ag ot A oa 26 6 1 General NSM UCT Oils pensan ERA AA AAA AA A 26 6 2 Handling the hand held tOOI xxx eseese naaa nana nana anna Kanan aaa 26 6 2 1 Reading an accessible SCNSOM cccccccccscceeceeeeeeceeseeeeeceesensans 27 6 2 1 1 Problem when reading communication failed 27 6 2 1 2 Problem when reading another sensor within range 28 6 2 2 Coding a sensor fitted in the tire erm naaa 28 6 2 2 1 Problem when coding 2 different sensors 29 6 3 Tire sensor Menu uuunuessensnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen 29 6 3 1 GECKO O ee er 30 69 2 Activate DENSON ee er 31 6 3 3 Deactivate Sensor ren rinnen einen 32 634 Clear LOO
34. ng main menu then appears CPC BE Installation Modification Diagnosis Setup Press the key again for approx 3 seconds to switch the hand held tool off CPC hand held tool Commissioning nfinental 5 5 Setting up the hand held tool Fundamental tool setup such as language units etc are determined in the Settings menu Menu item Meaning Selection Operating tal German French English anlage pungong Polish and Turkish screen Unit Unit for pressure and temperature Tempera ture Signal output as Sound ON OFF Sound setup sound and or NA vibration Vibration ON OFF Time after which the hand held tool Automatic is switched off switch off automatically Information in the Display of the FW version Version firmware and the serial number Tool setup Confirm the selected item with the return key A Press the ESC key to exit the sub menu and return to the Setup menu CPC hand held tool 25 ontinental Operation 6 Operation 6 1 General instructions For trouble free operation pay attention to the following instructions m Always operate the hand held tool with full charged batter ies so that full transmission power is ensured m Keep the cover of the hand held tool closed so that not dirt particles or fluids can penetrate the hand held tool 6 2 Handling the hand held tool In order to communicate with the tire sensors the hand held tool is equ
35. no sensor on the tire or the sensor is not operational 2 Dismantle the tire for exact checking 3 Continue as described in section 6 5 Resume initialization CPC hand held tool 45 ontinental 46 Operation 6 4 6 2 2 Different sensors found simultaneously The following message appears on the screen H XY 1 MORE THAN ONE SENSOR RECEIVED MOVE TOOL WITH SPEED SHOWN IN ANIMATION Repeat the coding process of the tire lf the hand held tool finds 2 sensor again the coding process is stopped and the following message appears H XY 1 MORE THAN ONE SENSOR RECEIVED LEARNING PROCESS STOPPED REFER TO MANUAL Press the Return key A to acknowledge the message Remedy Check wether additional sensors are located within a range of 2 m of the tires If yes remove the sensors from the communication range and repeat the coding procedure If no move the vehicle approx 1 m forwards or backwards and repeat the coding procedure CPC hand held tool Operation onfinenfal 6 4 6 3 Sensors not activated The following message appears on the screen H XY 1 SENSOR NOT ACTIVATED MOVE THE TOOL WITH SPEED SHOWN IN THE ANIMATION Press the Return key A to acknowledge the message Repeat the coding process of the tire The sensor is reset to park mode 9h and coded Code the next sensor CPC hand held tool 47 PERS 6 4 6 4 Transfer of configurat
36. ns empty An additional drive with named TPM O2 is displayed on the connected PC laptop Copy the new firmware into the root directory of the TPM 02 drive on the PC laptop gt If the PC laptop Displays Insufficient storage Space or data volume is full messages go to Cancel delete the file on the TPM 02 drive and repeat the copying procedure The copy progress is displayed on the PC lap top After completion of the copying procedure log the USB tool off the PC laptop Pull the USB cable out of the hand held tool and switch it on NOTE If the software update aborts during transfer updating can be repeated 66 CPC hand held tool Maintenance 1 2 Connection to the PC The files required for updating the firmware of the display CCU and the switching module CSW are stored on the SD memory card built into the hand held tool If new firmware versions are available the data on the SD memory card must be updated Diagnosis Connection to the PC For communication data transfer with the SD card the SD card can remain in the hand held tool Communication with the PC laptop takes place via the USB cable The current firmware for the display DSP CCU and the switching module CSW is available from www contipressurecheck com Check the website regularly for software updates To transfer the current firmware versions to the hand held tool pro ceed as follo
37. ressure Temperature Sound setup Sound Vibration Tool setup Automatic switch off Version release 18 CPC hand held tool ontinenfal Description 4 4 Menu control Operating the hand held tool takes place menu driven via the keys of the tool The following lists the possible operating steps 4 4 1 Calling a menu function Use the arrow keys 5 to select the desired menu items Press the Return key J to confirm the selection and call the menu item Ifthe menu includes sub menus use the arrow keys to select the desired menu item and confirm A to confirm on Press the ESC key ESC ESC to return to the previous menu level 4 4 2 Changing a selection Use the arrow keys to select the settings options Press the Return key A to confirm selection 4 4 3 Scroll symbol If the space on the screen is not sufficient to display all entries a scroll symbol appears on the right side JL or 1f Use the arrow keys Hi to call all entries CPC hand held tool 19 ontinental 20 4 5 Description Type plate The type plate is located on the underside of the tool z 17340230000 Continental a2c81336600 Handheld tool www contipressurecheck com Made in Italy AN FCC ID IFKTMP Tested To Comply with FCC Standards Other homologation see owner manual CONTAINS LI ION POLYMER BATTERY BATTERY 4 MUST BE RECYCLED OR DISPOSED OF PROPERLY Serial No TXXXXXXXXX Meaning
38. tion If the trainer has no power supply during installation The CCU of the trailer is supplied with current via the hand held tool This procedure is automatic If anew software version is available on the hand held tool the fol lowing message is displayed Software Update Be CCU VER 01 05 NEW VERSION 01 06 DSP CSW VER 00 06 NEW VERSION 00 07 PRESS TO UPDATE Software Update VER 01 05 CCU CCU UP TO DATE DSP CSW VER 00 06 NEW VERSION 00 07 PRESS TO UPDATE Press the Return key GJ to start software transfer for the CSW switching module CPC hand held tool Operation onfinenfal iy lf the software for the components was updated successfully the fol lowing message appears Software Update CCU VER 01 06 CCU UP TO DATE DSP CSW VER 00 07 CSW UP TO DATE gt Press the ESC key to return the diagnosis menu from any Software Update page CPC hand held tool 65 ontinental Maintenance Maintenance 7 1 Software Update for the hand held tool To update the software of the hand held tool proceed as follows Switch the hand held tool on off Connect the USB cable supplied to a free USB interface on the PC laptop Press and hold down the key on the hand held tool and connect the other end of the USB cable to the USB interface of the hand held tool The display lighting of the hand held tool is switched on the screen remai
39. tive for 2 ignition cycles m 0 DTCis still active The following error codes are possible NOTE Display of error codes is always in English irrespec tive of the selected operating language DTC Description Remedy Bad reception check the instal 90 The TTM is mute lation location of the CCU and or additional receiver 91 The tire is jammed Check whether the wheel can be freely rotated Low battery on TTM Replace TTM Low pressure the tire has an under inflation warning Increase tire pressure to recom mended value Check for damage If the tire is undamaged increase the tire pressure to the recommended value Very low pressure the tire has an under inflation alarm CPC hand held tool 59 ntinenfal Operation DTC Description Remedy Fast pressure loss the Check tire valve and wheel rim 15 tire has a leak alarm for leaks The TTM has detected a Tire sensor was subject to too S R high temperature Check func I p tion of tire and brakes 97 The TTM is defective Replace the tire sensor Thermal shutdown of Tire sensor was subject to too TTM due to high tem high temperature Check func perature tion of tire and brakes 16 Dismantle tire and check the installation location of the tire sensor in the rubber container Subsequently reset the Sensor is LOOSE message of the tire sensor as described in section 6 3 4 Clear LOOSE state The TTM is
40. trailer or only 1 axle semitrailer the page for determining the lift axle is not displayed Inthe case of trucks or drawbar trailers at least 2 ales may not be lift axles and in the case of the the semitrailer only 1 axle Inthe case of a truck or drawbar trailer the 1st axle can not be set as lift axle Altogether for each installation a maximum of 2 axles from possible 6 can be set as lift axle if the vehicle type is selected as MARRIED this is considered as one installa tion Lift axle setup must be made carefully If the axles are set incorrectly correct function of the CPC system for the incorrectly set lift axles cannot be ensured 40 CPC hand held tool Operation onfinenfal 6 4 4 Coding tire sensors Now each individual sensor scan be coded The current tire to be coded is marked on the the screen by to proceed C Take the hand held tool and go to the marked tire on the vehicle Press the Return key A to start the coding process An animation of the coding procedure appears on the screen Read the sensor with the hand held tool as described in section 6 2 2 Coding a sensor fitted in the tire Pay attention to the starting point and the direction of rotation in the animation CPC hand held tool 41 ontinental Operation lf the sensor is found in the marked tire the tire is filled black and the next tire to be coded is displ
41. wiring harness via the diagno sis cable Switch on the ignition Press the Return key J to start the transfer CPC hand held tool 43 Operation If the trainer has no power supply during installation The CCU of the trailer is supplied with current via the hand held tool This procedure is automatic The following message appears during transfer H XY 1 Upload in progress Please wait If data transfer is successful the following message appears H XY 1 Upload completed The previously set configuration is always stored on the hand held tool The advantage of this is that ini tialization of several vehicles with the same configu ration is easier 44 CPC hand held tool Sa Operation Continental 6 4 6 Possible problems 6 4 6 1 Sensor not found after 2 attempts Sensor was not found after the first coding attempt The following message appears on the screen H XY 1 NO SENSOR FOUND MOVE THE TOOL WITH SPEED SHOWN IN THE ANIMATION Repeat the coding process of the tire If the hand held tool does not find the sensor after the second at tempt the coding process is stopped and the following message appears H XY 1 NO SENSOR FOUND LEARNING PROCESS STOPPED CHECK IF SENSOR IN TIRE Press the Return key J to acknowledge the message Remedy 1 Check the charging state of the hand held tool If the charging state is sufficient there is
42. ws Select the Diagnosis Connection to the PC menu item and press Enter to confirm The following appears CPC hand held tool ontinenfal 6 ER Continental Maintenance Connect the hand held tool to the PC laptop via the USB cable The following appears gt This procedure can take a little longer the first time until the hand held tool is recognized gt The connection procedure can take place in reverse order Connect the USB cable first and then run Diagno sis Connection to the PC Follow the instructions on data transfer at www contipres surecheck com Log off the hand held tool under Windows and remove the USB cable 68 CPC hand held tool Cntinental Maintenance 7 3 Replacing the fuse in the diagnosis cable lf communication with the pressure control indicator or the power supply of the trailer CCU via the diagnosis cable is not possible the fuse in the diagnosis cable must be replaced Only use original 315 mA series 373 TR5 fuses from Wickmann To replace the fuse in the diagnosis cable proceed as follows Remove the old fuse see arrow Carefully insert the new fuse pay attention to the position of the pins E CPC hand held tool 69 ontinental Troubleshooting 7 4 Cleaning If dirty clean the housing of the hand held tool with a slightly damp lint free cloth Do not use cleaners containing solvents 7 5 Storage The
Download Pdf Manuals
Related Search