CPAP Manual - ActiveForever
Contents
1. 16 Cleaning or Replacing the Filtersss sc iscsssssccessssssosasisssassseisecssoassassesasaessbessadeussussousedecsssosesveseasoassouecondasscubpadeedecasensie 16 Cleaning the WUD i E ia 16 Service 16 Specifications 3417 Disposal atteinte eec ss 19 How to Contact Philips Respironics EMC INFOrmation m 19 Limited Warranty e M Back Page User Manual CAUTION U S federal law restricts this device to sale by or on the order of a physician Intended Use The Philips Respironics REMstar SE system delivers positive airway pressure therapy for the treatment of Obstructive Sleep Apnea in spontaneously breathing patients weighing over 30kg 66 Ibs It is for use in the home or hospital institutional environment Important The device is to be used only on the instruction of a licensed physician Your home care provider will make the correct pressure settings according to your health care professional s prescription Several accessories are available to make your OSA treatment with the REMstar SE system as convenient and comfortable as possible To ensure that you receive the safe effective therapy prescribed for you use only Philips Respironics accessories Warnings A warning indicates the possibility of injury to the user or the operator This manual serves as a reference The instructions in this manual are not intended to supersede th2. For Indoor Use Only Do not disassemble For Airline Use Complies with RTCA DO 160F section 21 category M 4649520 gt Y 3x Separate collection for electrical and electronic equipment per EC Directive 2002 96 EC Use only with the standard 60W power supply 1091398 not for use with Heated Tubing E m m E m m Use only with the Heated Tubing compatible 80W power supply 1091399 can also be used when Heated Tubing is not in use User Manual System Contents Your REMstar SE system may include the following items Device Side cover panel User manual SD card Carrying case Reusable gray foam filter Flexible tubing Disposable ultra fine filter optional Power cord Humidifier optional Power supply 60W REF 1091398 or 80W REF 1091399 Note If any of these items are missing contact your home care provider System Overview The REMstar SE is a CPAP Continuous Positive Airway Pressure device designed for the treatment of Obstructive Sleep Apnea OSA CPAP maintains a constant level of pressure throughout the breathing cycle When prescribed for you the device provides several special features to help make your therapy more comfortable The ramp function allows you to lower the pressure when you are trying to fall asleep The air pressure will gradually increase until your prescription pressure is reached You also have the optio
3. Where to Place the Device Place the device on a firm flat surface somewhere within easy reach of where you will use it at a level lower than your sleeping position Make sure the filter area on the back of the device is not blocked by bedding curtains or other items Air must flow freely around the device for the system to work properly Make sure the device is away from any heating or cooling equipment forced air vents radiators air conditioners CAUTION Do not place the device directly onto carpet fabric or other flammable materials CAUTION Do not place the device in or on any container that can collect or hold water Supplying AC Power to the Device CAUTION Condensation may damage the device If this device has been exposed to either very hot or very cold temperatures allow it to adjust to room temperature operating temperature before starting therapy Do not operate the device outside of the operating temperature range shown in the Specifications WARNING Be sure to route the power cord to the outlet in a way that will prevent the cord from being tripped over or interfered with by chairs or other furniture WARNING This device is activated when the power cord is connected IMPORTANT If you are using your device with a humidifier refer to the instructions included with your humidifier for details on how to power the device and humidifier Complete the following steps to operate the device using AC power i w User
4. PHILIPS s M s REMstar SE USER MANUAL RESPIRONICS activexXforever IMPROVING OUTCOMES IMPROVING LIVES www ActiveForever com Sales ActiveForever com p 1 800 377 8033 f 602 296 0297 2012 Koninklijke Philips Electronics N V All rights reserved Table of Contents Writer ded Se AAA gt i ni EEE AEE AEREE E ENERE 2 Important enisi NN 2 Wanne S its A E M R E 2 CAU da 3 COMtPAINGICACIONS m 3 Symbol Key 4 System Contents tii A IA Ecetia cias 5 System OVErViEW iaa 5 iS p plHlp prf 6 Available Therapies anos tia A TA 6 Installing the AIC FIIEBES airada neel ebde 6 Connecting the Breathing Circuit icsssssssscsssscoscsecssassesessssssossesescssassssossoesussobanescasousasudgsosedpeaesseessoasbdoubsnesecnssosweiesee 7 Where to Place the Device edi 7 Supplying AC Power to the Device certet cts testata ertet ee Lo tcd teca ras enn id 7 Display A M 8 Starting the DEE cda 9 Ramp Feature consti 9 Humidifier Preh6at oemcoimivinssrin in e 9 Navigating the Patient Settings nieee irintaj ansv 10 Device Messages iii rin ito AR 12 Enhanced Compliance Chet iii iii dci 12 Troubleshooting ii iaa 13 dll 15 Traveling with the timida dar 16 Cleaning the DEVICE so
5. equipment RF emissions Class B The device is suitable for use in all establishments including domestic establishments CISPR 11 and those directly connected to the public low voltage power supply network Harmonic emissions Class A IEC 61000 3 2 Voltage fluctuations Flicker emissions Complies IEC 61000 3 3 Guidance and Manufacturer s Declaration Electromagnetic Immunity This device is intended for use in the electromagnetic environment specified below The user of this device should make sure it is used in such an environment IMMUNITY TEST Electrostatic Discharge ESD IEC 61000 4 2 IEC 60601 Test LeveL 6 kV contact 8 kV air CoMPLIANCE LEVEL X6 kV contact X8 kV air ELECTROMAGNETIC ENVIRONMENT GUIDANCE Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 3076 Electrical fast Transient burst 2 kV for power supply lines 1 kV for input output lines 2 kV for supply mains 1 kV for input output lines Mains power quality should be that of a typical home or hospital environment 2 kV common mode IEC 61000 4 4 Surge 1 kV differential mode 1 kV differential mode Mains power quality should be that of a typical IEC 61000 4 5 home or hospital environment 2 kV for common mode Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000
6. 0 12 0 16 0 20 0 22mm Measured pressure at the patient 3 0 7 0 11 0 15 0 19 0 tubing connection port cm H O Average flow at the patient connection 33 2 36 8 41 0 45 6 48 1 port l min 15 mm Measured pressure at the patient 3 0 7 0 11 0 15 0 19 0 tubing connection port cm H O heated Average flow at the patient connection 278 311 350 379 414 SEO port l min heated Disposal Separate collection for electrical and electronic equipment per EC Directive 2002 96 EC Dispose of this device in accordance with local regulations How to Contact Philips Respironics To have your device serviced contact your home care provider If you need to contact Philips Respironics directly call the Philips Respironics Customer Service department at 1 800 345 6443 or 1 724 387 4000 You can also use the following address Respironics Inc 1001 Murry Ridge Lane Murrysville PA 15668 18 User Manual EMC Information Guidance and Manufacturer s Declaration Electromagnetic Emissions This device is intended for use in the electromagnetic environment specified below The user of this device should make sure it is used in such an environment Emissions TEST COMPLIANCE ELECTROMAGNETIC ENVIRONMENT GUIDANCE RF emissions Group 1 The device uses RF energy only for its internal function Therefore its RF emissions CISPR 11 are very low and are not likely to cause any interference in nearby electronic
7. Device Drip Proof IP22 60W power supply Drip Proof IP22 80W power supply Drip Proof IP22 Mode of Operation Continuous Electrical AC Power Consumption with 60W power supply 100 240 VAC 50 60 Hz 2 1 A AC Power Consumption with 80W power supply 100 240 VAC 50 60 Hz 2 0 A DC Power Consumption 12 VDC 6 67 A Fuses There are no user replaceable fuses Declared Dual Number Noise Emissions Values In accordance with ISO 4871 The measured A weighted emission sound pressure level is 29 3 dB A with an uncertainty of 1 6 dB A The measured A weighted sound power level is 37 3 dB A with an uncertainty of 1 6 dB A Notes These measurements apply to this device with an optional humidifier Use of this device without a humidifier would result in measurements equal to or less than the stated values Values determined according to noise test code given in ISO 17510 1 2007 using the basic standards ISO 3744 and ISO 4871 User Manual 17 Pressure Accuracy Pressure Increments 4 0 to 20 0 cm H O in 0 5 cm H O increments Pressure Stability Static Dynamic Dynamic 10 cm H O gt 10 0 to 20 cm H O Device 1 0 cm H O lt 2 0 cm H O lt 2 0 cm H O Device w Humidifier 1 0 cm H O lt 2 0 cm H O lt 2 0 cm H O 22 mm tubing Device w Humidifier 1 0 cm H O lt 2 0 cm H O lt 2 5 cm H O 15 mm tubing Maximum Flow Rate typical Test pressures cm H O 4 0 8
8. Manual Plug the socket end of the AC power cord included into the power supply also included IMPORTANT When you are using Heated Tubing with the compatible System One Heated Humidifier you must use the 80W power supply Plug the pronged end of the AC power cord into an electrical outlet that is not controlled by a wall switch Plug the power supply cord s connector into the power inlet on the back of the device Ensure that all connections are secure IMPORTANT To remove AC power disconnect the power supply cord from the electrical outlet WARNING Periodically inspect electrical cords and cables for damage or signs of wear Discontinue use and replace if damaged CAUTION Do not use extension cords with this device Display The display screen is shown here The information shown on the display is defined as follows DESCRIPTION Icon DESCRIPTION a le Z Device requires user attention Therapy ON OFF icon O Seven day average AN Altitude setting A Thirty day average Ramp duration setting b EOS Ramp starting pressure setting FLEX Flex setting Pressure setting SD card data activity z 3 D Heated humidifier Q Modem operation Backlight Prescription setting xU bd Therapy Hours Time Meter Ry Tubing type setting 8 User Manual Starting the Device Note The numbers shown in the screens throughout this manual are examples only Actual n
9. below the number you are in the Ramp time setting FLEX Flex setting The Flex comfort feature allows you to adjust the level of air pressure relief that you feel when you exhale during therapy Once you press the SELECT button to choose this setting the number will blink Use the LEFT RIGHT button to toggle between the available settings 1 2 or 3 The setting of 1 provides a small amount of pressure relief with higher numbers providing additional relief Press the SELECT button again to choose the setting If your provider has locked this setting you will see an L before the number and you will not be able to change it Tubing type setting This setting allows you to select the correct size diameter tubing that you are using with the device Once you press the SELECT button to choose this setting the number will blink Use the LEFT RIGHT button to toggle between the available settings You can choose either 22 for the Philips Respironics 22 mm tubing or 15 for the Philips Respironics 15 mm tubing When using Heated Tubing the device will automatically change this setting to the appropriate tubing type 15h and you will not be able to change it Note If the Heated Tubing is removed the device will default back to the previous tubing type setting User Manual 11 Device Messages The following icons may appear during use of this device These icons are used to provide information regarding t
10. the humidifier Refer to the humidifier manual When not using a humidifier this cover must be in place on the device User Manual 5 Control Buttons Display Area Ramp Button Start Stop or Select Button Left Right Navigation Button These features are described below FEATURE DESCRIPTION Display Area This area shows the therapy settings and patient data and other messages When the airflow is on this button allows you to activate or restart the ramp function Ramp lowers the Ramp Button a airflow pressure and then gradually increases it allowing you to fall asleep more easily Start Stop or Select Starts the airflow and places the device into Active state or stops the airflow and places the device into Button Standby state Also when navigating the patient screens press this button to select the menu options Left Right Navigation Performs display navigation or setting adjustments Button Note The control buttons are backlit and will be on when the device is plugged into a power outlet Available Therapies The REMstar SE device delivers the following therapies CPAP Delivers Continuous Positive Airway Pressure CPAP maintains a constant level of pressure throughout the breathing cycle CPAP with Flex Delivers CPAP therapy with pressure relief upon exhalation to improve patient comfort based on patient needs Installing the Air Filters CAUTION A proper
11. 4 11 lt 5 U gt 95 dip in U for 0 5 cycle 40 U 60 dip in U for 5 cycles 70 U 30 dip in U for 25 cycles lt 5 U 295 dip in U for 5 sec lt 5 U gt 95 dip in U for 0 5 cycle 40 U 60 dip in U for 5 cycles 70 U 30 dip in U for 25 cycles lt 5 U 295 dip in U for 5 sec Mains power quality should be that of a typical home or hospital environment If the user of the device requires continued operation during power mains interruptions it is recommended that the device be powered from an uninterruptible power supply or a battery Power frequency 50 60 Hz magnetic field IEC 61000 4 8 3 A m 3 Alm Power frequency magnetic fields should be at levels characteristic of a typical location in a typical hospital or home environment NOTE U is the a c mains voltage prior to application of the test level User Manual Guidance and Manufacturer s Declaration Electromagnetic Immunity This device is intended for use in the electromagnetic environment specified below The user of this device should make sure it is used in such an environment IMMUNITY TEST IEC 60601 Test Lever COMPLIANCE LEVEL ELECTROMAGNETIC ENVIRONMENT GUIDANCE Portable and mobile RF communications equipment should be used no closer to any part of the device including cables than the recommended separation distance calculated from the equation applicable to the freque
12. ater and a mild detergent Rinse thoroughly Air dry Note Refer to the humidifier manual for the instructions on how to clean the heated tube Service The device does not require routine servicing WARNING If you notice any unexplained changes in the performance of this device if it is making unusual or harsh sounds if it has been dropped or mishandled if water is spilled into the enclosure or if the enclosure is broken disconnect the power cord and discontinue use Contact your home care provider 16 User Manual Specifications Environmental Operating Temperature 5 to 35 C 41 to 95 F Storage Temperature 20 to 60 C 4 to 140 F Relative Humidity operating amp storage 15 to 95 non condensing Atmospheric Pressure 101 to 77 kPa 0 2286 m 0 7500 ft Physical Dimensions 18 x 14 x 10 cm 7 L x 5 5 W x 4 H Weight Device with power supply Approximately 1 53 kg 3 37 Ibs Standards Compliance This device is designed to conform to the following standards IEC 60601 1 General Requirements for Safety of Medical Electrical Equipment EN ISO 17510 1 Sleep Apnea Breathing Therapy Devices EN 60601 1 2 Electromagnetic Compatibility RTCA DO 160F section 21 category M Emission of Radio Frequency Energy IEC 60601 1 Classification Type of Protection Against Electric Shock Class Il Equipment Degree of Protection Against Electric Shock Type BF Applied Part Degree of Protection against Ingress of Water
13. ay orange changes to blue Incorrect power supply is being used 60W is used instead of 80W Heated Tubing is attached incorrectly or damaged Make sure the 80W power supply is being used This can be confirmed by looking at the power supply for the 60W or 80W symbols Inspect Heated Tubing for damage and reconnect If the problem continues contact your home care provider 14 User Manual Accessories There are several accessories available for your REMstar SE system such as a humidifier or a modem Contact your home care provider for additional information on the available accessories When using optional accessories always follow the instructions enclosed with the accessories CAUTION Pins of connectors marked with the ESD warning symbol shall not be touched and connections shall not be made without special precautions Precautionary procedures include methods to prevent build up of electrostatic charge e g air conditioning humidification conductive floor coverings non synthetic clothing discharging one s body to the frame of the equipment or system or to earth It is recommended that all individuals that will handle this device understand these precautionary procedures at a minimum as part of their training Adding a Humidifier with or without Heated Tubing You can use the heated humidifier and the heated tube with your device They are available from your home care provider A humidifier and heated tu
14. be may reduce nasal dryness and irritation by adding moisture to the airflow WARNING For safe operation the humidifier must always be positioned below the breathing circuit connection at the mask and the air outlet on the device The humidifier must be level for proper operation Note Refer to the humidifier s instructions for complete setup information Using the SD Card The REMstar SE system may come with an SD card inserted in the SD card slot on the back of the device to record information for the home care provider Your home care provider may ask you to periodically remove the SD card and send it to them for evaluation The SD card does not need to be installed for the device to work properly Contact your provider if you have any questions about the SD card Adding Supplemental Oxygen Oxygen may be added at the mask connection Please note the warnings listed below when using oxygen with the device WARNINGS When using oxygen with this system the oxygen supply must comply with local regulations for medical oxygen Oxygen supports combustion Oxygen should not be used while smoking or in the presence of an open flame When using oxygen with this system a Philips Respironics Pressure Valve must be placed in line with the patient circuit between the device and the oxygen source The pressure valve helps prevent the backflow of oxygen from the patient circuit into the device when the unit is off Failure to use the pressure valve could r
15. continues relocate the device to an area with lower EMI emissions away from electronic equipment such as cellular phones cordless phones computers TVs electronic games hair dryers etc If the problem still occurs contact your home care provider for assistance The Ramp feature does not work when you press the Ramp button Your CPAP pressure is already set to the minimum setting Ramp Time setting is set to 0 or your Ramp Starting Pressure is the same as your prescribed pressure If your CPAP is already set to the minimum setting 4 0 cm H O then the Ramp feature is not available This cannot be changed If your Ramp Time setting is set to zero increase the time to anywhere between 5 and 45 minutes Refer to Navigating the Patient Settings section of this manual for instructions If your Ramp Starting Pressure is the same as your prescription pressure decrease the Ramp Starting Pressure so that it is lower than your prescription pressure To verify your prescription pressure start the airflow on your device and note the number on the display You can then verify and change the Ramp Starting Pressure as described in the Navigating the Patient Settings section of this manual The airflow is much warmer than usual User Manual The air filters may be dirty The device may be operating in direct sunlight or near a heater Clean or replace the air filters The temperature of the a
16. e device Contraindications When assessing the relative risks and benefits of using this equipment the clinician should understand that this device can deliver pressures up to 20 cm H O In the event of certain fault conditions a maximum pressure of 30 cm H O is possible Studies have shown that the following pre existing conditions may contraindicate the use of CPAP therapy for some patients Bullous Lung Disease Pathologically Low Blood Pressure Bypassed Upper Airway Pneumothorax Pneumocephalus has been reported in a patient using nasal Continuous Positive Airway Pressure Caution should be used when prescribing CPAP for susceptible patients such as those with cerebral spinal fluid CSF leaks abnormalities of the cribriform plate prior history of head trauma and or pneumocephalus Chest 1989 96 1425 1426 The use of positive airway pressure therapy may be temporarily contraindicated if you exhibit signs of a sinus or middle ear infection Not for use with patients whose upper airways are bypassed Contact your health care professional if you have any questions concerning your therapy User Manual Symbol Key The following symbols may appear on the device and power supply SYMBOL DEFINITION Ti Consult accompanying instructions for use EAS AC Power E DC Power Drip Proof Equipment Caution consult accompanying documents ESD Warning symbol Class Il Double Insulated Type BF Applied Part
17. e carrying case will not protect the system if it is put through checked baggage For your convenience at security stations there is a note on the bottom of the device stating that it is medical equipment and is suitable for airline use It may be helpful to bring this manual along with you to help security personnel understand the REMstar SE device If you are traveling to a country with a line voltage different than the one you are currently using a different power cord or an international plug adaptor may be required to make your power cord compatible with the power outlets of the country to which you are traveling Contact your home care provider for additional information Airline Travel The REMstar SE device is suitable for use on airlines when the device is operating from an AC or DC power source Note It is not suitable for airline use with any of the modems or humidifiers installed in the unit Cleaning the Device WARNING To avoid electrical shock always unplug the power cord from the wall outlet before cleaning the device DO NOT immerse the device in any fluids 1 Unplug the device and wipe the outside of the device with a cloth slightly dampened with water and a mild detergent Let the device dry completely before plugging in the power cord 2 Inspect the device and all circuit parts for damage after cleaning Replace any damaged parts Cleaning or Replacing the Filters Under normal usage you should clean the gray foam filt
18. e health care professional s instructions regarding the use of the device The operator should read and understand this entire manual before using the device This device is not intended for life support The device should be used only with masks and connectors recommended by Philips Respironics or with those recommended by the health care professional or respiratory therapist A mask should not be used unless the device is turned on and operating properly The exhalation port s associated with the mask should never be blocked Explanation of the Warning The device is intended to be used with special masks or connectors that have exhalation ports to allow continuous flow of air out of the mask When the device is turned on and functioning properly new air from the device flushes the exhaled air out through the mask exhalation port However when the device is not operating enough fresh air will not be provided through the mask and exhaled air may be rebreathed Rebreathing of exhaled air for longer than several minutes can in some circumstances lead to suffocation e If you are using a full face mask a mask covering both your mouth and your nose the mask must be equipped with a safety entrainment valve When using oxygen with this system the oxygen supply must comply with local regulations for medical oxygen Oxygen supports combustion Oxygen should not be used while smoking or in the presence of an open flame When using oxygen
19. e is activated when the power cord is connected For safe operation when using a humidifier the humidifier must always be positioned below the breathing circuit connection at the mask and the air outlet on the device The humidifier must be level for proper operation Note Please see the Limited Warranty section of this manual for information on warranty coverage Cautions A Caution indicates the possibility of damage to the device Medical electrical equipment needs special precautions regarding EMC and needs to be installed according to EMC information Contact your home care provider regarding EMC installation information Mobile RF communications equipment can affect medical electrical equipment Pins of connectors marked with the ESD warning symbol shall not be touched and connections shall not be made without special precautions Precautionary procedures include methods to prevent build up of electrostatic charge e g air conditioning humidification conductive floor coverings non synthetic clothing discharging one s body to the frame of the equipment or system or to earth It is recommended that all individuals that will handle this device understand these precautionary procedures at a minimum as part of their training Before operating the device ensure that the SD card cover is replaced whenever any of the accessories such as the Link Module or Modem are not installed Refer to the instructions that came with your accessory Cond
20. ensation may damage the device If this device has been exposed to either very hot or very cold temperatures allow it to adjust to room temperature operating temperature before starting therapy Do not operate the device outside of the operating temperature range shown in the Specifications Do not use extension cords with this device Do not place the device directly onto carpet fabric or other flammable materials Do not place the device in or on any container that can collect or hold water A properly installed undamaged reusable foam inlet filter is required for proper operation Tobacco smoke may cause tar build up within the device which may result in the device malfunctioning Dirty inlet filters may cause high operating temperatures that may affect device performance Regularly examine the inlet filters as needed for integrity and cleanliness Never install a wet filter into the device You must ensure sufficient drying time for the cleaned filter Always ensure that the DC power cord securely fits into your therapy device prior to use Contact your home care provider or Philips Respironics to determine if you have the appropriate DC cord for your specific therapy device When DC power is obtained from a vehicle battery the device should not be used while the vehicle s engine is running Damage to the device may occur Only use a Philips Respironics DC Power Cord and Battery Adapter Cable Use of any other system may cause damage to th
21. equential damages which may be claimed to arise from any sale or use of this product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty is given in lieu of all other express warranties In addition any implied warranties including any warranty of merchantability or fitness for the particular purpose are limited to two years Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state To exercise your rights under this warranty contact your local authorized Respironics Inc dealer or contact Respironics Inc at 1001 Murry Ridge Lane Murrysville Pennsylvania 15668 8550 1 724 387 4000 Respironics Inc 1001 Murry Ridge Lane Murrysville PA 15668 USA PHILIPS REF 1096462 1096314 R02 JR 3 28 2012 EN DOM
22. er at least once every two weeks and replace it with a new one every six months The white ultra fine filter is disposable and should be replaced after 30 nights of use or sooner if it appears dirty DO NOT clean the ultra fine filter CAUTION Dirty inlet fileers may cause high operating temperatures that may affect device performance Regularly examine the inlet filters as needed for integrity and cleanliness If the device is operating stop the airflow Disconnect the device from the power source 2 Remove the filter s from the enclosure by gently squeezing the filter in the center and pulling it away from the device 3 Examine the filter s for cleanliness and integrity 4 Wash the gray foam filter in warm water with a mild detergent Rinse thoroughly to remove all detergent residue Allow the filter to air dry completely before reinstalling it If the foam filter is torn replace it Only Philips Respironics supplied filters should be used as replacement filters If the white ultra fine filter is dirty or torn replace it 6 Reinstall the filters inserting the white ultra fine filter first if applicable CAUTION Never install a wet filter into the device You must ensure sufficient drying time for the cleaned filter Ui Cleaning the Tubing Clean the flexible tubing before first use and daily Disconnect the flexible tubing from the device For the 15 or 22 mm flexible tubing gently wash the tubing in a solution of warm w
23. es may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 20 User Manual Limited Warranty Respironics Inc warrants that the system shall be free from defects of workmanship and materials and will perform in accordance with the product specifications for a period of two 2 years from the date of sale by Respironics Inc to the dealer If the product fails to perform in accordance with the product specifications Respironics Inc will repair or replace at its option the defective material or part Respironics Inc will pay customary freight charges from Respironics Inc to the dealer location only This warranty does not cover damage caused by accident misuse abuse alteration water ingress and other defects not related to material or workmanship The Respironics Inc Service department shall examine any devices returned for service and Respironics Inc reserves the right to charge an evaluation fee for any returned device as to which no problem is found after investigation by Respironics Inc Service This warranty is non transferable by unauthorized distributors of Respironics Inc products and reserves the right to charge dealers for warranty service of failed product not purchased directly from Respironics Inc or authorized distributors Respironics Inc disclaims all liability for economic loss loss of profits overhead or cons
24. esult in a fire hazard Note Refer to the pressure valve s instructions for complete setup information When using oxygen with this system turn the device on before turning on the oxygen Turn the oxygen off before turning the device off This will prevent oxygen accumulation in the device Do not connect the device to an unregulated or high pressure oxygen source Supplying DC Power to the Device The Philips Respironics DC Power Cord can be used to operate this device in a stationary recreational vehicle boat or motor home The Philips Respironics DC Battery Adapter Cable when used with the DC Power Cord enables the device to be operated from a 12 VDC free standing battery CAUTION Always ensure that the DC power cord securely fits into your therapy device prior to use Contact your home care provider or Philips Respironics to determine if you have the appropriate DC cord for your specific therapy device CAUTION When DC power is obtained from a vehicle battery the device should not be used while the vehicle s engine is running Damage to the device may occur CAUTION Only use a Philips Respironics DC Power Cord and Battery Adapter Cable Use of any other system may cause damage to the device Refer to the instructions supplied with the DC Power Cord and adapter cable for information on how to operate the device using DC power User Manual 15 Traveling with the System When traveling the carrying case is for carry on luggage only Th
25. evice Contact your health care professional if symptoms of sleep apnea recur e If you notice any unexplained changes in the performance of this device if it is making unusual or harsh sounds if it has been dropped or mishandled if water is spilled into the enclosure or if the enclosure is broken disconnect the power cord and discontinue use Contact your home care provider Repairs and adjustments must be performed by Philips Respironics authorized service personnel only Unauthorized service could cause injury invalidate the warranty or result in costly damage Periodically inspect electrical cords and cables for damage or signs of wear Discontinue use and replace if damaged To avoid electrical shock always unplug the power cord from the wall outlet before cleaning the device DO NOT immerse the device in any fluids If the device is used by multiple persons such as rental devices a low resistance main flow bacteria filter should be installed in line between the device and the circuit tubing to prevent contamination 2 User Manual Be sure to route the power cord to the outlet in a way that will prevent the cord from being tripped over or interfered with by chairs or other furniture Using this device at an incorrect altitude setting could result in airflow pressures higher or lower than the prescribed setting Always verify the altitude setting when travelling or relocating and adjust the system accordingly This devic
26. gradually increases ramps the pressure until your prescription setting is reached allowing you to fall asleep more comfortably You can use the RAMP button as often as you wish during the night Note If the Ramp feature is on the Ramp icon 4 will display below the current pressure setting Humidifier Preheat When using a humidifier the device can preheat the water tank for up to 30 minutes prior to starting therapy In order to activate the preheat mode the device must be in the standby state and have a humidifier attached Then press and hold down the SELECT button for 5 seconds The humidifier icon will illuminate and the device will now be in preheat mode During the 30 minute preheat you will still be able to select other menu options If you begin therapy during this time preheat mode will end and the current humidity setting 0 1 2 3 4 or 5 will now take effect User Manual 9 Navigating the Patient Settings When the device is in the standby state press and hold either the LEFT or RIGHT button for at least 2 seconds to enter the patient settings You can then use the LEFT RIGHT button 4 gt to navigate the patient settings shown here N ty A x OL Are Note You can only enter these settings when the device is in standby state Once you highlight the setting that you want to change press the SELECT button You can then use the LEFT RIGHT button lt D to adjust that setti
27. he status of the device and are not associated with any device settings ICON 6 NAME SD Card Icon DEscRIPTION ACTION If an SD card is inserted in the device the SD card icon will be displayed while usage information is being recorded to the SD card You do not need to take any special action when this icon is displayed If this icon is flashing this means that an error was encountered while writing to the SD card Remove SD card and reinsert If the alert continues to occur contact your home care provider e Modem Icon If a modem is attached to the device the modem icon will be displayed while data is being transferred You do not need to take any special action when this icon is displayed Re Prescription Icon If the device has been programmed with a new prescription the prescription icon will be displayed for several seconds If the prescription icon is displayed along with the alert icon shown below this means that an error was encountered while programming the new prescription Remove SD card and reinsert If the alert continues to occur contact your home care provider N Alert Icon When the unit detects a system error the alert icon is displayed When this occurs the blower is automatically turned off and pushbutton functions are disabled In order to use the device the system error needs to be resolved Remove the power supply cord from the device to remove power Plug the c
28. here s no power at the outlet or the device is unplugged WHAT ro Do If you are using AC power check the outlet and verify that the device is properly plugged in Make sure there is power available at the outlet Make sure the AC power cord is connected correctly to the power supply and the power supply cord is securely connected to the device s power inlet If the problem continues to occur contact your home care provider Return both the device and power supply to your provider so they can determine if the problem is with the device or power supply If you are using DC power make sure your DC power cord and battery adaptor cable connections are secure Check your battery It may need recharged or replaced If the problem persists check the DC cord s fuse following the instructions supplied with your DC cord The fuse may need to be replaced If the problem still occurs contact your home care provider The airflow does not turn on There may be a problem with the blower Make sure the device is powered correctly when pressing the SELECT button to start airflow If the airflow does not turn on there may be a problem with your device Contact your home care provider for assistance The device s display is erratic The device has been dropped or mishandled or the device is in an area with high Electromagnetic Interference EMI emissions Unplug the device Reapply power to the device If the problem
29. ht setting for the device screen Once you press Md Z Backlight the SELECT button to choose this setting the number will blink Use the LEFT RIGHT button to toggle W setting between the available settings O off 1 2 or 3 for variable brightness Press the SELECT button again to choose the setting This setting allows you to view your therapy usage in hours Once this icon is highlighted the device will scroll through the 3 available Therapy Hours screens total accumulated therapy hours the 7 day therapy x icd average shown with the 7 icon and the 30 day average shown with the 30 icon ours Note You can also access the Enhanced Compliance Check from this setting Refer to the Enhanced Compliance Check section of this manual for more information Th l ONCE When this icon is highlighted Press the START STOP button to turn the airflow on or off 10 User Manual ICON Name Altitude setting DESCRIPTION This screen allows you to modify the altitude adjustment setting Once you press the SELECT button to choose this setting the number will blink Use the LEFT RIGHT button to toggle between the available settings 1 less than 762 m 2500 ft 2 762 m to 1524 m 2500 to 5000 ft 3 1525 m to 2286 m 5001 to 7500 ft Note Elevations over 2286 m 7500 ft may affect the accuracy of the pressure Press the SELECT button again to save the new setting Warning Using th
30. ir may vary somewhat based on your room temperature Make sure that the device is properly ventilated Keep the device away from bedding or curtains that could block the flow of air around the device Make sure the device is away from direct sunlight and heating equipment If using the humidifier with the device check the humidifier settings Refer to the humidifier instructions to make sure the humidifier is working properly If the problem continues contact your home care provider 13 PROBLEM The airflow pressure feels too high or too low Why IT HAPPENED The Tubing type setting may be incorrect Whar ro Do Make sure the Tubing type setting 22 or 15 matches the tubing that you are using Philips Respironics 22 or 15 mm tubing If you are using the Heated Tubing this setting will be 15h and you cannot change it The Heated Tubing is being used and is turned on in the Heated Humidifier settings but the Heated Tubing is not warm Incorrect power supply is being used 60W is used instead of 80W Heated Tubing is attached incorrectly or damaged Make sure the 80W power supply is being used This can be confirmed by looking at the power supply for the 60W or 80W symbols Inspect Heated Tubing for damage and reconnect If the problem continues contact your home care provider The Heated Tubing is being used and is turned on in the Heated Humidifier settings but the Humidifier LED does not st
31. is device at an incorrect altitude setting could result in airflow pressures higher or lower than the prescribed setting Always verify the altitude setting when travelling or relocating and adjust the system accordingly IN Ramp start pressure setting Ramp time setting This screen allows you to modify the ramp starting pressure Once you press the SELECT button to choose this setting the number will blink Use the LEFT RIGHT button to increase or decrease the ramp starting pressure from 4 0 cm H O to your prescription pressure in 0 5 cm H O increments Press the SELECT button again to save the new setting Note The Ramp start pressure setting uses the same icon as the Ramp time setting If cm H O is highlighted below the number you are in the Ramp start pressure setting This screen allows you to set the ramp time The device increases the CPAP pressure from the Ramp Starting Pressure 4 cm H O to the CPAP prescription pressure setting over the length of time specified here Once you press the SELECT button to choose this setting the number will blink Use the LEFT RIGHT button to set the ramp time in 5 minute increments from 0 to 45 Press the SELECT button again to save the new setting Note If the CPAP pressure is set to 4 or this setting is set to 0 nothing will happen when you press the RAMP button Note The Ramp time setting uses the same icon as the Ramp start pressure setting If cm H O is NOT highlighted
32. ly installed undamaged reusable gray foam filter is required for proper operation The device uses a gray foam filter that is washable and reusable and an optional white ultra fine filter that is disposable The reusable filter screens out normal household dust and pollens while the optional ultra fine filter provides more complete filtration of very fine particles The gray reusable filter must be in place at all times when the device is operating The ultra fine filter is recommended for people who are sensitive to tobacco smoke or other small particles A reusable gray foam filter and a disposable ultra fine filter are supplied with the device If your filters are not already installed when you receive your device you must at least install the reusable gray foam filter before using the device To install the filter s 1 If you are using the white disposable ultra fine filter insert it into the filter area first mesh side facing in towards the device 2 Insert the gray foam filter into the filter area after the ultra fine filter Note If you are not using the white disposable filter simply insert the gray foam filter into the filter area 6 User Manual Connecting the Breathing Circuit To use the system you will need the following accessories in order to assemble the recommended circuit Philips Respironics interface nasal mask or full face mask with integrated exhalation port or Philips Respironics interface with a separate e
33. n of not using the ramp feature at all Additionally the Flex comfort feature provides you with pressure relief when you exhale during therapy Several accessories are also available for use with your device Contact your home care provider to purchase any accessories not included with your system SD Card Accessory Slot Air Outlet Port Filter Area This figure illustrates some of the device features described in the following table Device FEATURE DESCRIPTION Air Outlet Port Connect the 15 or 22 mm Philips Respironics flexible tubing here conical 22 mm Note Heated Tubing should only be connected to the Air Outlet Port of the compatible System One Heated Humidifier and not to the Air Outlet Port of the therapy device SD Card Accessory Slot If applicable insert the optional accessory SD card here SD Card Cover If applicable the optional accessories such as a Link Module or Modem can be installed here Refer to the instructions supplied with the accessory When not using an accessory this cover must be in place on the device Power Inlet Connect the power cord here Filter Area A reusable gray foam filter must be placed in the filter area to screen out normal household dust and pollens A white ultra fine filter can also be used for more complete filtration of very fine particles Side Cover If using a humidifier with the device this side cover can be easily removed with the release tab before attaching
34. ncy of the transmitter Recommended separation distance Conducted RF 3 Vrms 3 Vrms d 12NP IEC 61000 4 6 150 kHz to 80 MHz d 12NP 80 MHz to 800 MHz Radiated RF 3 V m d 23NP 800 MHz to 2 5 GHz IEC 61000 4 3 80 MHz to 2 5 GHz 3 V m where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol ej NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above the device should be observed to verify normal operation If abnormal perfo
35. ng Press the SELECT button again to save the new setting These settings are described here Icon Name DESCRIPTION If using a humidifier on your device this setting allows you to choose the humidifier mode and the desired humidity setting Once you press the SELECT button to choose this setting the letter will blink Use the LEFT RIGHT button to scroll between the available humidifier modes c o or h The humidifier has 3 different modes Classic c System One o and Heated Tube h The Heated Tube h option will only display if you are using the heated tubing with the humidifier and the 80W power supply The humidifier icon will Heated change color to indicate which mode is being used White is Classic c Blue is System One o and Humidifier Orange is Heated Tube h This icon will also display this color during therapy when the humidifier is setting applying heat Press the SELECT button again and the number will now blink Use the LEFT RIGHT button to scroll between the available humidity settings 0 off 1 2 3 4 or 5 Press the SELECT button again to choose the setting You can also access only the humidity setting screen during therapy Simply press the LEFT RIGHT button during therapy and the humidity setting will display Use the LEFT RIGHT button to choose the new humidity setting The screen will automatically switch back to the Monitor Pressure screen This setting allows you to choose the desired backlig
36. ord back into the device s power inlet to restore power If the alert continues to occur contact your home care provider Enhanced Compliance Check To view the Enhanced Compliance Check screen highlight the Therapy Hours icon E when the device is in the standby state Then press and hold both the LEFT navigation button lt and the SELECT button for 5 seconds The device will then display the following 5 screens It will cycle through these screens twice before returning to the standby state DisPLay DESCRIPTION 4XX Where XX is the 2 digit month for the start date 3XX Where XX is the 2 digit day for the start date 2XX Where XX is the 2 digit year for the start date 1XX Where XX is the number of days that the device was used for longer that 4 hours OXX Where XX is the 2 digit check code number used by your home care provider to validate the data Note If compliance data is not available for 70 or more of the last 30 days the device will not display the information stated above Instead the device will display 3 dashes Note Your home care provider may periodically ask you for this information 12 User Manual Troubleshooting The table below lists some of the problems you may experience with your device or mask and possible solutions to those problems PROBLEM Nothing happens when you apply power to the device The backlights on the buttons do not light Why IT HAPPENED T
37. rmance is observed additional measures may be necessary such as re orienting or relocating the device b Over the frequency range 150 kHz to 80 MHz the field strengths should be less than 3 V m Recommended Separation Distances between Portable and Mobile RF Communications Equipment and This Device The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of this device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and this device as recommended below according to the maximum output power of the communications equipment RATED MAXIMUM POWER SEPARATION DISTANCE ACCORDING TO FREQUENCY OF TRANSMITTER OUTPUT oF TRANSMITTER M Ww 150 kHz ro 80 MHz 80 MHz ro 800 MHz 800 MHz ro 2 5 GHz dz124P dz124P dz 2 JP 0 12 0 12 0 23 0 1 0 38 0 38 0 73 1 12 13 23 10 3 8 3 8 7 3 100 12 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer Note 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note 2 These guidelin
38. umbers will vary 1 Plug the device into an AC power source The complete display screen will light up briefly followed by the Software Version screen for a few seconds 2 The control buttons will then light up which indicates that the device in now in the standby state 3 Press the START STOP button to turn on the airflow Put on your mask assembly when the air starts to flow Note There will be a short pause after pressing the START STOP button until the air starts to flow 4 The Monitor Pressure screen will then appear gp shown here am i cm H20 O Monitor Pressure Screen The Monitor Pressure screen shows the current pressure setting in cm H O 5 Make sure that no air is leaking from your mask into your eyes If it is adjust the mask and headgear until the air leak stops See the instructions provided with your mask for more information Note A small amount of mask leak is normal and acceptable Correct large mask leaks or eye irritation from an air leak as soon as possible Note If you are using the device in bed try placing the tubing from the device over your headboard This may reduce tension on the mask Note You must remove the mask and patient circuit before you get out of bed 6 Press the START STOP button fo again to turn off therapy Ramp Feature You can press the RAMP Y button during therapy to activate the Ramp feature This feature reduces the air pressure when you are trying to fall asleep and then
39. with this system turn the device on before turning on the oxygen Turn the oxygen off before turning the device off This will prevent oxygen accumulation in the device Explanation of the Warning When the device is not in operation and the oxygen flow is left on oxygen delivered into the tubing may accumulate within the device s enclosure Oxygen accumulated in the device enclosure will create a risk of fire When using oxygen with this system a Philips Respironics Pressure Valve must be placed in line with the patient circuit between the device and the oxygen source The pressure valve helps prevent the backflow of oxygen from the patient circuit into the device when the unit is off Failure to use the pressure valve could result in a fire hazard Do not connect the device to an unregulated or high pressure oxygen source Do not use the device in the presence of a flammable anaesthetic mixture in combination with oxygen or air or in the presence of nitrous oxide Do not use the device near a source of toxic or harmful vapors Do not use this device if the room temperature is warmer than 35 C 95 F If the device is used at room temperatures warmer than 35 C 95 F the temperature of the airflow may exceed 43 C 109 F This could cause irritation or injury to your airway Do not operate the device in direct sunlight or near a heating appliance because these conditions can increase the temperature of the air coming out of the d
40. xhalation device such as the Whisper Swivel II WARNING If you are using a full face mask a mask covering both your mouth and your nose the mask must be equipped with a safety entrainment valve Philips Respironics 22 mm or 15 mm flexible tubing 1 83 m 6 ft Philips Respironics headgear for the mask WARNING If the device is used by multiple persons such as rental devices a low resistance main flow bacteria filter should be installed in line between the device and the circuit tubing to prevent contamination To connect your breathing circuit to the device complete the following steps 1 2 3 Connect the flexible tubing to the air outlet on the side of the device Note Make sure the Tubing type setting 15 or 22 matches the tubing you are using Philips Respironics 15 or 22 mm tubing Note Heated Tubing should only be connected to the Air Outlet Port of the compatible System One Heated Humidifier and not to the Air Outlet Port of the therapy device Note If required connect a bacteria filter to the device air outlet and then connect the flexible tubing to the outlet of the bacteria filter Note When using the bacteria filter the device performance may be affected However the device will remain functional and deliver therapy Connect the tubing to the mask Refer to the instructions that came with your mask Attach the headgear to the mask if necessary Refer to the instructions that came with your headgear
Download Pdf Manuals
Related Search