Manual - COP
Contents
1. Note If you shut down your device but don t exit the menu setup interface all settings set above will not be saved 3 Specification 13 User Manual of SDI Dome Camera Model HD SDI Dome Camera Sensor 1 3 CMOS Pixel 2010 H x 1092 V Shutter 1 25s or 1 30s 1 67500s Min illumination OLUX Resolution 1000TVLines Camera Lens f lt 42mm White balance ATW indoor outdoor manual etc Day amp Night ICR S N ratio gt SOdB IR range 15m Weather proof IP66 3D NR Yes Image adjust it E O Advance lt J Z Mirror Lens shading Size Video Frame Video out Port Alarm out BLC HLC Area Level Offsetup Sharpness brightness etc 100dB Rotate mirror flip Yes 1080P 1920 x 1080 30fps NTSC 25fps PAL 1 ch SDI 1 0Vp P 75ohm No Powersupply DCI2V Temperature 10 C 50 C Working Humidity 10 90 environment Dimension 0 123mm 90mm Weight 450g net weight 14 450013000045 AO ANY2. 2 Mega Pixel HD SDI Dome Camera User Manual Thank you for purchasing our product This manual is only applicable to SDI bullet cameras There may be several technically incorrect places or printing errors in this manual The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual The content is subject to change without notice User Manual of SDI Dome Camera Before using the product please read this manual carefully to ensure that user can use the product correctly to avoid danger or property loss Please store this instruction manual in a safe place for future reference A Warning Input voltage should meet both the SELV Safety Extra Low Voltage and the Limited Power Source with DC 12V Please refer to technical specifications for detail information B Ifthe product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not be responsible for any problems caused by unauthorized repair or maintenance B Keep away from liquid while in use B In the use of the product you must be strict compliance with the electrical safety regulations of the nation and region User Manual of SDI Dome Camera When the product is mounted on wall or ceiling the device shall be firmly fixed A Cautions B Make sure
3. NR interface Select D NR level and push left right to increase or decrease the NR level in the daytime Select N NR level and push left right to increase or decrease the NR level at night The higher the level is the less the noise 1s Sharpness Select Sharpness to enter into sharpness setup interface Select N level and push left right to setup the value of sharpness at night Select D level and push left right to setup the value of sharpness in the daytime Brightness Push left right to setup the value of brightness Gamma Setup the value of GAMMA Blue Gain Push left right to increase or decrease the value of red Lens Shading Push left right to select On Off NTSC PAL Press left right to select NTSC or PAL Return Return to the previous interface or exit menu setup 12 User Manual of SDI Dome Camera 2 9 Reset This function is reset all setups to the default status If parameters of the camera are out of order and the camera cannot display images you may use this function to reset all setups Please select Reset and press Enter button to go into its setup interface Then select Factory and press Enter button to reset all settings to the default factory settings Additionally you can also check up the version of the camera here Select Return to return to the menu setup interface Push left right to select Exit to exit the menu setup interface and return to the live interface The system will automatically save the settings
4. VOT OR OIT rea EERE 4 Basic Operating Instruction sinica zravnano 4 CNG o a aa 2 E DO a aa kuma ra a sia e bU 3 White Balante eO 8 Day Ge Sd cO 9 vjuzur m 9 ase OUST M P 11 loo M 13 User Manual of SDI Dome Camera Introduction It adopts the advanced Panasonic CMOS sensor and supports 1080P real time image capture and transmission It features high definition and sensibility amp low noise and distortion which is extremely suitable for the application of surveillance and image processing system 1 1 Package Content The pictures below are only for reference Please take the real object as standard Device User manual Screwdriver 4 bw Vanad l D s aj od 1 2 Main Features High Resolution and sensibility 1080P real time image with high definition and good color reproduction The sensibility is up to 0 LUX due to the installation of the high quality of the built in removable optical filter User Manual of SDI Dome Camera X HD SDI video output High Light Control HLC Mask and compensate the high light areas so as to make right exposure selection DNR Under low illumination condition user can reduce noise from brightness and color signal to save a lot of storage room OSD The setup menu clearly displays the functions and features of the camera and 3 languages can be selected It is easy for users to set up the corre
5. by pushing right The default mode is EXT mode Color Return to the Mode setup interface and press Right button to select this mode B W Select this mode and press Enter button to setup Burst Press right left to select on off If you want to obtain the standard B W signal please select off EXT Ifthis mode is selected light resource and image will be changed synchronously as the change of the external light dependent control element Smart IR Select smart IR and press Enter button to set On off When the object with IR light is captured please enable it and then enter into its submenu for level and area setup 2 7 Special Push right left to setup language camera title motion privacy and defect User Manual of SDI Dome Camera Language There are three languages English CHT and CHS Camera title Select it and press Enter button to select On Off When selecting On the title edition and the position selection of the title is effective User can press the direction button to self define the camera name After selecting the single letter number or symbol please press Enter button to go into the camera title position setup User can push the direction button to set up Mirror Mirror the current image There are three kinds of mirror Rotate Mirror and Flip Motion Select Motion and press left right to select On Off Select On and press Enter button to set up motion Select There are three areas to set up Dis
6. function to see the object behind fog clearly There are four options low middle high off Backlight You can select OFF BLC or HSBLC by pushing right If OFF is selected the system will not compensate the image If BLC is selected it will enhance the brightness of image to satisfy the monitor effect To enter into the submenu of BLC press Enter button You can setup GAIN AREA and DEFAUT Gain The higher the level is the brighter the image 1s When selecting on the area position and size can be setup Push direction button to set the position of BLC area After User Manual of SDI Dome Camera that press Enter button to setup the area size Push up or left to reduce the area but push down or right to enlarge the area If parameters of BLC setup are out of order please select Default and press Enter button to reset settings If HSBLC is selected the high brightness will be restrained and the low brightness will be enhanced at the same time As aresult the image ina certain area will be exposed properly Please use the fixed IRIS Lens This function can be used to shoot license plate number Select HSBLC and press Enter button to go into its submenu Select There are four areas Please push direction button to select Display Display the HSBLC areas There are four areas Press Enter button to setup the position and size Level Push left or right to increase or decrease Mode There are two modes All Day and
7. night Black Mask Mask the highlight area Default Reset the setup of HSBLC to the default setting Select Return and press Enter button to return to the previous interface Select Return push right and choose exit to exit Menu User Manual of SDI Dome Camera 2 5 White Balance Select WHITE BAL and push left or right to choose White balance mode including ATW AWC SET Indoor Outdoor and Manual ATW In this mode the camera will constantly monitor the color temperature among about 2500 9500K of color temp and adjust white balance automatically This mode is prior to other modes AWC SET Select it and press Enter button to go into the lock mode of white balance Now the camera locks the reference value of red and blue under the current color temperature and stops monitoring color temperature Indoor Indoor white balance mode Outdoor Outdoor white balance mode Manual When the camera is used in the environment with a certain unchangeable light source user can use this mode Select this mode and press Enter button to setup User can adjust the level of blue and red by pushing left or right button to reach the reasonable results of white balance Return Select Return and press Enter button to return to the previous interface User Manual of SDI Dome Camera 2 6 Day Night Select Day amp Night and press Enter button to setup its mode and smart IR Mode Three options Color B W EXT User can select it
8. play Push right left to select On Off Select on and press Enter button to set its size and position Sensitivity Push right left to adjust the sensitivity of the detection area Motion view If enabled there will be some red square appearing when there are something moving Default Reset all settings of Motion to the default value 10 User Manual of SDI Dome Camera Return Return to the previous interface Privacy Ifa user wants to mask some areas please select On and press Enter button to go into the privacy setup interface e Select There are 8 areas to select Display Display the area size and position Color There are 16 colors to select for the area Default Reset all settings of Privacy to the default value Return Return to the previous interface Defect Including Live DPC Level Static DPC Start and Level settings Live DPC The default setting is Auto When selecting it the system will automatically check the defect point There is no need for you to set up the level Push left right to select On Off Level Level of live Defect Point Correction Return Return to the previous interface 2 8 Image Adjust Select Image Adjust and press Enter button to go into Image Adjust interface 11 User Manual of SDI Dome Camera User can setup 3D NR sharpness brightness Gamma blue gain red gain lens shading and NTSC PAL 3D NR Select itand press Enter button to go into 3D
9. power cable and then the system will shut down immediately 2 2 Basic Operating Instruction When enterring into the setup menu user can see the picture as shown above J means that there are submenus User can select and confirm the item by pushing the direction button and OK button User Manual of SDI Dome Camera SETUP LENS EXPOSURE WHITE BAL DAY amp NIGHT SPECIAL IMAGE ADJUST RESET Push up or down to select the item on the left column Push left or right to select the item on the right column Press the enter button to confirm the selection and enter into the submenu interface 2 3 Lens Setup Support manual IRIS and DC lens Please setup according to the use of lens User can select the lens type by pushing right 2 4 Exposure Exposure setup includes Shutter AGC Sens up WDR Defog and Backlight Shutter Options include auto 1 30 1 60 FLK 1 250 1 500 1 1000 x 2 AGC When the light is insufficient push left righ to setup 5 User Manual of SDI Dome Camera its level The default level is 6 Please increase or decrease t he level as required Sens up Extend the exposure time of c amera The higher the tine is the lower the frame is Th e shadow will be longer underthe dark condition Please select times by pushing right as needed WDR Lighten the dark area and control the highlight area There are four options low middle high off Defog In foggy weather you can setup this
10. sponding items ICR Switch The camera provides two operation modes color and B amp W User can increase sensitivity in low light conditions night by switch to B amp W mode Color mode is preferred in normal lighting condition Day Privacy Masking When there are not necessary for some area to display in the screen user can mask this area Backlight Compensation BLC User Manual of SDI Dome Camera When the back of the captured object is bright user can set up backlight compensation for the captured object to make it more clearer X Motion Detection eWhen the camera captures the moving object in the detection area it will send signal So it is easy for users to monitor the live 1 3 Direction Key and Connector Open the housing of the camera by screwdriver and find the black button Please refer to the above picture Push the button up to make the cursor move up Push the button down to make the cursor move down Push the button to the left or right to select the left or right item Press the button to confirm the selection pr D User Manual of SDI Dome Camera 1 HD SDI Video Output connect monitor with high definition 2 Connect power supply Operation Instruction 2 1 Power On Off Before starting connect with the power cables and video cables Please make sure all the connection is good After that the system will start Then press the OK button to pop up the setup menu Plug out the
11. the power supply voltage is correct before using the camera B Do not drop the camera or subject it to physical shock B If cleaning is necessary please use clean cloth to wipe it gently If the device will not be used for a long time please cover the lens cap to protect the device from dirt B Do not aim the camera at the sun or extra bright place A blooming or smear may occur otherwise which is not a malfunction however and the endurance of the device will be affected at the same time B The device may be burned out by a laser beam so when any laser equipment is in use make sure that the surface of the device will not be exposed to the laser beam M To avoid heat accumulation good ventilation is required for operating environment User Manual of SDI Dome Camera B Do not place the camera in extremely hot cold the operating temperature shall be 10 C 50 C dusty or damp locations and do not expose it to high electromagnetism radiation B While on a delivery the camera shall be packed in its original packing or packing of the same texture B A few parts of the device shall be replaced regularly according to their average enduring time Regular checking is recommended for all users 1 2 1 3 ZA 2 2 229 2 4 255 2 0 dal 2 8 29 kadi garant ON OM AM 1 Package Content nani ie malai l ITO Wi ee s a a l Direction Key and Connector nana errore vika 3 Operation Instr ction savine ke v ja vala 4 PO
Download Pdf Manuals
Related Search