MA-9OOOAH Portable Air Conditioner
Contents
1. DRY appears on the LCD display 5 Fan Operation a b 4 7 Timer a Press the ON OFF key to turn on the unit Press the Mode key unit COOL appears on the LCD display Press either A or V key of the temperature to set the temperature HIGHER than the current room temperature Press the Fan Speed key until the LCD displays the desired fan speed When the unit is On press Timer Button then press the Hour button until the 13 desired number of hours is displayed in the LCD The unit will automatically power Off once the selected number of hours has elapsed b When the unit is Off press Timer Button then press the Hour button until the desired number of hours is displayed in the LCD The unit will automatically power On once the selected number of hours has elapsed NOTE The timer function must be manually reset before each automatic start or stop CONDENSATE WATER DRAINAGE 1 Internal Water Bucket When operating in cooling or dehumidifying mode the condensate water will drain into the internal water bucket Depending on the surrounding humidity the unit can continuously operate for 2 to 12 hours before the internal water bucket is full When the internal water bucket becomes full the red Water Full light located on the front of the unit will flash The compressor will stop but the fan will continue to run at the set speed To empty the water bucket Turn the2. OWNER S MANUAL MA 9000AH Portable Air Conditioner Cooling Heating Dehumidifying Fan O _ carefully before operating the C US unit LISTED TABLE OF CONTENTS INTRRODUCTION sekerli ilen ea vee Bada GN Dy EE UD 3 IMPORTANT SAFEGUARDS erer seansa anan aaa 3 IDENTIFYING THE 4 ASSEMBLY REQUIREMENTS CONTROL PANEL AND LCD DISPLAY 7 CONTROL PANEL FUNCTIONS 8 OPERATION USING CONTROL PANEL 9 OPERATION USING REMOTE CONTROLLER 1 1 0000 aananan 11 CONDENSATE WATER DRA NAGE erer renas aranan anan 14 TECHNICALSPEC FICATTIONS eee erer enem eses erener DISCLA MER erener erener aneen sanane ananem sanane een 18 CONTACT INFORMAT ON erener erener 18 INTRODUCTION Thank you for purchasing the Soleus Air MA 9000AH portable air conditioner This unit is designed to improve living and working comfort by providing cooling dehumidifying and fan functions with only minimum installation required With its whisper quite operation and attractive design you will enjoy the conv
3. this manual unintended use may void the warranty PACKAGE CONTAINS 1 Portable Air Conditioner 1 Air Exhaust Duct I Window Kit 2 Sliding Panels Window Kit Adapter I Remote Controller 2 AAA Batteries I User Manual IDENTIFYING THE PARTS Front View Control Panel Up down Air Swinging Fins Air Outlet Left right Swinging Fins Caster Water Tank Cable power Cord and Plug Rear View Upper Air Inlet Grill Filter Hot Air Outlet Grill Lower Air Inlet Grill Window Kit Adaptor ASSEMBLY REQUIREMENTS 1 Exhaust Duct When you use the unit as an air conditioner the hot exhaust air must be directed out of the room The exhaust duct is required to allow the hot air out of the room through a window DO NOT INSTALL OR USE THE EXHAUST DUCT WHEN THE UNIT IS OPERATED AS A DEHUMIDIFIER OR FAN Slide Unit Terminal End of the exhaust connector completely over the Hot Air Outlet Grill on the rear of the unit Plastic grooves are located on the hot air outlet help to guide the exhaust connector into place Window Kit Mounting Connect the window kit adapter to the external end of the exhaust duct The exhaust duct is now ready to be attached to the window kit See page 7 for window kit installation Wall Mounting Mount the external end of the exhaust duct to a 5 hole within the wall Creating a hole into a wal
4. activates the oscillating louvers Operation Using the Control Panel 1 Cooling Operation a Be sure that the drain bucket is properly placed in the unit If the drain bucket is not properly secured the red Water Full light located on the front panel will blink and the unit will not begin cooling Be sure the exhaust duct properly installed Refer to page 6 for exhaust duct installation Plug the Power Cord to the power outlet Turn on the unit by pressing the On Off Button on the control panel Press the Mode Button until COOL appears on the LCD display Press the Temperature Button A or until the desired room temperature appears on the LCD The temperature ranges from 63 F 88 F 17 C 31 C After two seconds the current room temperature will appear on the LCD screen NOTE During hot days the unit will cool off the room most efficiently by setting the temperature to the lowest setting and the fan speed to the highest setting see page 9 for fan operation Reducing the length of the exhaust duct insulating the exhaust duct and keeping direct sunlight to a minimum will also improve the cooling efficiency 2 Dehumidifying Operation Be sure that the drain bucket is properly placed in the unit If the drain bucket is not properly secured in the unit the red Water Full light located on the front panel will blink and the unit will not begin dehumidifying If exhaust duct is attached remove it from t
5. cate the desired temperature When FAULT is displayed the displayed digits indicate the code of failures Control Panel Functions 1 Power On Off Control Starts or stops the unit 2 Temperature Setting Control Select the desired temperature setting by pressing either the Display of Time Setting The displayed digits indicate the remaining time of on off operation Fan speed indicator A or key It is recommended to set the temperature before selecting the Mode Control 3 Mode Control Select the functions of the unit for a Air Conditioning Mode COOL b Dehumidifying Mode DRY c Heating Mode HEAT 4 Fan Speed Control Select the fan speed for a High b Medium c Low 5 Timer Time Sets the amount of time in hours to automatically start or to stop the unit 8 When the unit is On press Timer Button then press the Time button until the desired number of hours is displayed in the lower right corner of the display window The unit will automatically power Off once the selected number of hours has elapsed When the unit is Off press Timer Button then press the Time button until the desired number of hours is displayed in the lower right corner of the display window The unit will automatically power On once the selected number of hours has elapsed NOTE The timer function must be manually reset before each automatic start or stop 6 Swing Activates or de
6. enience and comfort that this unit provides for many years to come When operating as an air conditioner this unit is designed for spot cooling or cooling for a room no larger than 300 square feet with a standard ceiling height of 8 feet IMPORTANT SAFEGUARDS Before installing and using the portable air conditioner please read this Owner s manual carefully l 2 Never use or store gasoline or other flammable vapor or near this unit Maintain at least 10 25cm clearance space around all side of the unit Do not obstruct air inlet or outlet grilles All in home wiring must comply with local and national codes and be installed by a qualified technician The power supply must be properly grounded wiring problems should be resolved by a qualified technician BEFORE installation and use of this air conditioner Always inspect the power cord and plug for signs of damage before use For your safety this unit is grounded through the power cord plug when connected to a matching wall outlet Do not use an adapter plug or extension cord When removing the power cord from the wall outlet always grasp the plug firmly and pull straight from the outlet Never unplug the air conditioner by pulling on the cord itself Do not use the unit in the immediate surroundings of a bath a shower or a swimming pool Never immerse the unit in water or any other liquid Keep out of reach of children Use product only as directed in
7. h 1 ambient sunlight is reaching in There is frost on the evaporator The water bucket is not This unit provides spot cooling or cooling for a room no larger than 300 square feet with standard ceiling height There is frost on the evaporator The unit will defrost automatically and return to operation afterwards The unit will defrost automatically and will return to operation afterwards The water bucket is full Empty the water bucket Completely insert the water installed correctl bucket Noise or vibration Surface is not level Place unit on a level surface and away from obstructions Water 1s leaking from unit Surface is not level Place unit on a level surface Drainage plug is loose Make drain tube is properly secured and plugged TECHNICAL SPECIFICATIONS 17 CONTACT INFORMATION Optional or Spare Parts Technical Support Warranty Claims Soleus International Inc 1 888 876 5387 MODEL MA 9000AH COOLING CAPACITY 9000 BTU hr HEATING CAPACITY 1100 W DEHUMIDIFYING CAPACITY 88 Pints Day POWER COOLING HEATING 1120W 1350W DEHUMIDIFYING 1100W AIR FLOW VOLUME 180 CFM POWER SOURCE VOLTAGE 115 V 60 HZ RATED CURRENT 11 5 AMP COOLING 11 7 AMP HEATING SOUND PRESSURE LEVEL 54 db NET WEIGHT 77 Lbs DIMENSIONS BODY 1774 x 14 x 32 Inches PACKAGE 26 x 18 x 34 Inches REFRIGERANT R22 WATER BUCKET VOLUME 4L NOTE 1 The above cooli
8. he rear of the air conditioner Plug the Power Cord to the power outlet Turn on the unit by pressing the On Off Button on the control panel Press the Mode Button until DRY appears on the LCD display NOTE Do not use the exhaust duct when the unit is running at dehumidifying mode You must remove the exhaust duct from the unit When the unit is running at dehumidifying mode the fan speed cannot be adjusted Keep the windows and the doors closed to aid the efficiency of the unit in removing the moisture from the room 3 Fan Operation a b Plug the Power Cord to the power outlet Turn on the unit by pressing the On Off Button on the control panel Press the Mode Button until COOL appears on the LCD display Press the Temperature Button A or to set the temperature HIGHER than the current room temperature After two seconds the current room temperature will appear on the LCD screen Set the fan speed to LOW MEDIUM or HIGH by pressing the Fan Speed button 4 Heating Operation a b 4 Plug the Power Cord to the power outlet Turn on the unit by pressing the On Off Button on the control panel Press the Mode Button until Heat appears on the LCD display Press the Temperature Button A 27 until the desired room temperature appears on the LCD The temperature ranges from 63 F 88 F 17 C 3 1 C NOTE When the unit is operating in heating mode the exhaust duct is not
9. ir conditioner while in the possession of a consumer not caused by a defect in material or workmanship 2 Damage caused by consumer misuse tampering or failure to follow the care and special handling provisions in the instructions 3 Damage to the finish of the case or other appearance parts caused by wear 4 Filter 5 Damage caused by repairs or alterations of the air conditioner by anyone other than authorized by Soleus International Inc 6 Freight and Insurance cost for the warranty service This warranty covers only new products purchased from our authorized dealers or retailers It does not cover used salvaged or refurbished products ALL WARRANTIES INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY ARE LIMITED TO ONE YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY SOLEUS INTERNATIONAL INC DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT SHALL SOLEUS INTERNATIONAL INC S LIABILITY EXCEED THE RETAIL VALUE OF THE AIR CONDITIONER FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS AIR CONDITIONER Serial No
10. l is a separate procedure that may require professional installation NOTE In order to achieve maximum room cooling efficiency the exhaust duct should remain as short and straight as possible To further shorten the exhaust hose first unthread either exhaust duct adapter clockwise to remove it Then cut the hose to desired length It is not recommended to increase the manufacturer s length of the exhaust hose This may reduce the cooling efficiency or damage the unit 2 Window Kit Installation a Open window approximately 5 inches 13 cm b Adjust the length of the window kit to the same length of the window use both panels if necessary The window kit has a maximum length 50 5 inches c Place the window kit between the window and the window frame as shown in the picture to the right Close the window onto the window kit to form a tight seal d Attach the exhaust duct window kit adapte to the window kit Tabs located on the adapter will lock into place securing the adapter to the window kit NOTE Using the window kit will cause the window not to be properly closed and locked Additional security measurements should be taken CONTROL PANEL AND LCD DISPLAY CONTROL PANEL DISPLAY 4 NG TIMER TIME TEMP MODE TEMP FAN SPEED SWING A Operation mode indicator Display of preset temperature and failure code When SET is displayed the displayed digits indi
11. ng capacity is measured at ambient temperature of DB 86 F WB 78 F 2 Noise level is measured at the point where is 3 28 ft away from the front of the unit in cooling mode 3 Power consumption is measured when fan runs at the highest speed Specifications above are for reference only Please see the actual data printed on the nameplate DISCLAIMER ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER S MANUAL ARE THE PRESENTATION OF THE MANUFACTURER SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT TEST OF THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN Contact Customer Service at our tool free number for WARRANTY ONE YEAR LIMITED WARRANTY Soleus International Inc warrants the accompanying MA 9000AH Soleus Air air conditioner to be free of defects in material and workmanship for the applications specified in its operation instruction for a period of ONE 1 year from the date of original retail purchase in the United States or Canada If the air conditioner exhibits a defect in normal use Soleus International Inc will at its option either repair or replace it free of charge within a reasonable time after the air conditioner is returned during the warranty period As condition to any warranty service obligation the consumer must present this Warranty Certificate along with a copy of the original purchase invoice THIS WARRANTY DOES NOT COVER 1 Damage accidental or other wise to the a
12. ot included or adapter not provided if necessary Place the other end of the hose into either an external water bucket a floor drain or the intake side of a condensate water pump NOTE When using the continuous drainage method the unit will NOT shut off automatically when an external water bucket is full Spill water can cause substantial damages to carpet floors furniture and other valuables NOTE Do not use a lengthy drainage hose without a condensate water pump as water may overflow into the internal drain bucket which requires periodic manual drainage MAINTENANCE Note Before performing any maintenance activities turn the unit off and remove the power plug from the power outlet 15 1 Clean or Replace Filter a Ifthe air filter is clogged the airflow volume will decrease reducing cooling efficiency Itis recommended to clean the filter once a month or as needed Filter caver pi bocka b Push down the tab on the filter cover and pull outwards to remove the entire filter and cover c Carefully remove the air filter from the filter cover d Wash the air filter by immersing it gently into warm water with a mild detergent e Rinse the filter thoroughly and dry it in a shaded place f Attach the filter to the filter cover with the attachment hooks located on the inside surface of the cover g Place the bottom of the filter cover into the holes in the unit case Push the cover back in
13. required 10 OPERATION USING REMOTE CONTROLLER REMOTE CONTROLLER Temperature Setting Button Use the buttons to increase or decrease the desired room temperature 4 Turns the unit on or off Mode Selection Button Pressing this button will select COOL HEAT or DRY mode Fan Speed Button Sets the fan speed to High medium or lows Timer Button Sets the amount of time in hours to automatically start or stop the unit Press HOUR button to select the number of desired hours Swing Button Pressing this button activates or deactivates the oscillating louvers Hour and Minute Buttons Se _ Hold Button Sets the current time number Press this button to lock or unlock of hours for auto start and stop the keypad 1 To Set the Clock Open the back cover of the remote controller and insert two AAA batteries When batteries 11 installed or replaced the clock is set to 12 00AM To set present time Press the CLK button Removethe back cover push the clock botton with the tip of a ball pen etc When the time indicator flashes the current time may be set Press the HOUR button to Select the hour Press the MIN button to Select the minute Slide the F back cover by Press the CLK botton again then reattach the back cover 2 Cooling Operation a Besure that the drain bucket is prope
14. rly placed in the unit If the drain bucket is not properly secured the red Water Full light located on the front panel will blink and the unit will not begin cooling b Be sure the exhaust duct properly installed Refer to page 6 for exhaust duct installation c Plug the Power Cord to the power outlet d Press the ON OFF key to turn on the unit e Press the Mode key until the LCD displays COOL f Press either A of VW key of the Temperature key until the LCD displays the desired temperature g Press the Fan Speed key until the LCD displays the desired fan speed 3 Heating Operation Plug the Power Cord to the power outlet Turn on the unit by pressing the On Off Button on the remote control Press the Mode Button until Heat appears on the LCD display Press the Temperature Button A until the desired room temperature appears on the LCD The temperature ranges from 63 F 88 F 17 C 31 C NOTE When the unit is operating in HEAT mode the exhaust duct is not required 4 Dehumidifying Operation Be sure that the drain bucket is properly placed in the unit If the drain bucket is not properly secured the red Water Full light located on the front panel will blink and the unit will not begin dehumidifying If attached remove the exhaust duct from the back of the air conditioner Plug the Power Cord to the power outlet Press the ON OFF key to turn on the unit Press Mode key until
15. to its original position 2 Case a Avoid direct exposure to sunlight as case color may fade b Clean surface area with a damp cloth Dry with a soft towel Do not use abrasive cleaning products 3 Storing the Unit for an Extended Period of Time or Transporting Unplug the unit from the power outlet Ensure that the water bucket is empty Ifusing continuous drainage disconnect any external drain hose and cap the end of the internal drain tube d Store and transport unit in an upright position Store unit in a cool dry place TROUBLESHOOTING 16 PROBLEM POSSIBLE CAUSE REMEDY Unit does not operate Unit is unplugged Securely plug receptacle into the power outlet Drain bucket is full Empty water bucket Water bucket not installed correctly Completely insert water bucket Air exhaust is clogged Remove obstruction from exhaust hose Timer is on Cancel the timer Unit does not cool room In dehumidifying mode no cool air coming out Water Full indicator is blinking There is a heating source in the room Turn down or off the other heating source Temperature setting is too high Lower temperature setting Air filter is dirty Clean or replace the air filter Air exhaust is not installed correctly Check the exhaust duct to make sure that the hot exhaust air is being vented out of the room Room is too big or too muc
16. unit off b Remove water bucket slowly and discard the water inside the bucket c Place the bucket back to its original position d Turn the unit on The drain bucket may be emptied before it is full First turn off the unit then wait 3 minutes before removing the water bucket to prevent the condensate water from discharging into the unit NOTE Ifyou remove the water bucket while the unit is operating in cooling or dehumidifying mode the red Water Full Light will flash and the compressor will stop Once the drain bucket is placed back in the unit the compressor will remain off for approximately 3 minutes before restarting the cooling or dehumidifying cycle 2 Continuous Drainage The unit can operate on continuous drainage mode When the unit is operating on continuous drainage mode condensate water will not drain into the internal water bucket Condensate water 14 is discharged by gravity through a drainage tube 127 length to either an external hose not included or to a condensate water pump device not included When the unit is operating on continuous drainage mode it can operate continuously without periodic stops to empty the water bucket To allow continuous drainage a Remove the water bucket from the cabinet b Find the tube hanging beside the water bucket inside of the cabinet c Remove the plug from the end of the tube Garden hose d Connect the drainage tubing to a hose Use a clamp n
Download Pdf Manuals
Related Search