engine oil pressure gauge engine oil pressure gauge
Contents
1. Wipe off excess oil grease and dirt from OIL FILTER ACCESS TOOL assembly and hose gauge assembly after every use Visually inspect the silicone washer for damage or worn out There are two extra silicone washers in each kit Additional silicone washers and parts are available from TPR1 Keep all moving parts lightly oiled for years of good service TOOL REMEDIES A Locking Thumb Piece is not holding Ratchet Remove pivot pin thumb piece and spring Bend open spring for more tension Reinstall components B Locking Thumb Piece is not holding Ratchet Remove pivot pin thumb piece and spring Bend thumb piece slightly downward locking tooth end to change engagement angle on ratchet Reinstall components C Pivot Pin loose Remove pivot pin thumb piece and spring Bend pivot pin eye tabs slightly twist Reinstall components D Piercing Quick Connect Coupler Probe edge damaged Resharpen angle on probe with emery paper only TPR1 Division TPR 2331 W Hampden Ave 130 Englewood CO 80110 303 781 9449 www tpr1 com2. message and in some instances an icon An icon when present i ical ription of th ntial hazard GLASS LENS ON GAUGE CAN BREAK gives a graphical description of the potential hazard ai pe cee DO NOT USE GAUGE IF GLASS LENS 1 WARNING RISK OF FLYING PARTICLES IS CRACKED OR BROKEN WEAR SAFETY GOGGLES USER AND BROKEN GLASS CAN CAUSE INJURY BYSTANDER DO NOT EXCEED 100 PSI 700 kPa BE SURE ALL CONNECTIONS ARE SECURE FLYING PARTICLES CAN CAUSE INJURY RISK OF HIGH PRESSURE OIL SPRAY s WHILE ENGINE IS RUNNING RMING Sra epe e Aea BEFORE PERFO DO NOT REMOVE OIL FILTER ACCESS TOOL SET PARKING BRAKE AND PUT GEAR WHILE ENGINE IS RUNNING SELECTOR IN NEUTRAL FOR STANDARD HIGH PRESSURE OIL SPRAY CAN CAUSE INJURY TRANSMISSION OR PARK FOR AUTOMATIC TRANSMISSION CHECK MANUFACTURERS SERVICE MANUAL FOR PROCEDURES A MOVING VEHICLE CAN CAUSE INJURY SAVE THESE INSTRUCTIONS Continued unt Functional Description Figure 1 KT28 Engine Oil Pressure Gauge Oil Filter Access Tool A PRESSURE GAUGE HOSE ASSEMBLY Displays oil pressure of engine from 0 100 PSI 0 700 kPa B OIL FILTER ACCESS TOOL Tightens and locks around the oil filter C 1 4 ELBOW KEY Used to tighten the OIL FILTER ACCESS TOOL around the oil filter Continued unt Tool S et Up Continued FIGURE 1 Is an application lists of the components included in this kit If an adapter 45 or 90 degree 1 8 NPT street elb
3. DAMAGE OF TOOL CAUTION LOOSEN 2 SCREWS ON RATCHET INSERT KEY INTO RATCHET HOLD KEY THEN RELEASE THUMB PIECE ALWAYS TURN KEY TO OPEN TOOL NEVER SNAP TOOL OPEN BY RELEASING THUMB PIECE WITHOUT KEY THIS WILL DAMAGE THE RATCHET HOLDING CAPABILITIES OF OIL FILTER ACCESS TOOL Continued unt Test Procedure RISK OF SUDDEN VEHICLE MOVEMENT BLOCK DRIVE WHEELS BEFORE PERFORMING OIL PRESSURE TEST SET PARKING BRAKE AND PUT GEAR SELECTOR IN NEUTRAL FOR STANDARD TRANSMISSION OR PARK FOR AUTOMATIC TRANSMISSION CHECK MANUFACTURERS SERVICE MANUAL FOR PROCEDURES A MOVING VEHICLE CAN CAUSE INJURY 1 With the engine off clean area on oil filter where the OIL FILTER ACCESS TOOL assembly will be installed 2 Open the OIL FILTER ACCESS TOOL large enough to slip over the oil filter Using the elbow wrench or drive ratchet Tighten the OIL FILTER ACCESS TOOL so that the coupler assembly pierces the oil filter wall Snug up the OIL FILTER ACCESS TOOL assembly DO NOT over tighten Refer to FIGURE 3 RN A Figure 3 Oil Filter Access Tool installed with Gauge Hose assembly Continued unt Test Procedure continued 3 Connect the male connector gauge hose assembly to the quick connect coupler on the OIL FILTER ACCESS TOOL assembly Place the gauge hose assembly away from the exhaust manifold exhaust pipes or any moving parts of the engine 4 Start engine and chec
4. E FROM DEFECTS IN WORKMANSHIP AND MATERIALS FOR ONE 1 YEAR FROM THE DATE OF PURCHASE BY THE ORIGINAL COMSUMER TPR1 will repair or replace this gauge set if it fails to give satisfactory service due to defective workmanship or materials Repair or replacement shall be at the election and expense of TPR1 Product must be returned to TPR1 for warranty service unless such return is unreasonable Proof of purchase date is required to make warranty claim TPR1 dose NOT provide any warranty for products subjected to abnormal use Abnormal use includes misuse accident modification unreasonable use neglect lack of maintenance use in production related service or use after tool is significantly worn TPR1 SHALL NOT BE LIABLE FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL COST OR DAMAGES INCURRED BY THE PURCHASER OR OTHERS including without limitation lost profits revenues anticipated sales business opportunities goodwill or interruption of business and any other injury or damage some states do not allow the exclusion or limitations of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty is your exclusive remedy and is in place of all other rights and remedies You may have other rights which vary from state to state or country For further information contact TPR1 Division TPR 2331 W Hampden Ave 130 Englewood CO 80110 303 781 9449 www tpr1 com unt Tool Maintenance
5. k for oil leaks at the OIL FILTER ACCESS TOOL adapter connection If there is any leakage immediately turn the engine off and correct the problem Restart the engine and proceed with the engine oil pressure testing RISK OF HIGH PRESSURE OIL SPRAY DO NOT REMOVE GAUGE HOSE ASSEMBLY WHILE ENGINE IS RUNNING DO NOT REMOVE OIL FILTER ACCESS TOOL WHILE ENGINE IS RUNNING HIGH PRESSURE OIL SPRAY CAN CAUSE INJURY Oil pressure readings should be checked at operating engine temperatures Refer to manufacturers service manual for accurate engine oil pressure specifications and testing procedures 5 After completing the engine oil pressure test Turn engine off Remove connector gauge hose assembly from OIL FILTER ACCESS TOOL Use rubber cap to seal the male connector from unwanted leakage when storing gauge hose assembly To remove OIL FILTER ACCESS TOOL assembly INSERT elbow wrench or drive ratchet unload the tension from the thumb locking piece ALWAYS TURN with elbow wrench or ratchet to open tool NEVER SNAP TOOL OPEN by releasing thumb piece This will DAMAGE the locking thumb piece holding release capabilities Remove the OIL FILTER ACCESS TOOL assembly Remove and discard punctured oil filter REPLACE with new one 6 Check oil level and correct as necessary ENGINE OIL PRESSURE GAUGE OIL FILTER ACCESS TOOL Limited One 1 Year Warranty KT28 TPR1 COMPANY WARRENTS THIS OIL PRESSURE GAUGE OIL FILTER ACCESS TOOL TO BE FRE
6. ow is not required The male connector fitting can be threaded on the end of the pressure gauge hose assembly FIGURE 2 Shows the order of components when installing the piercing quick connect coupler D and internal star washer C into one of the three holes in the OIL FILTER ACCESS TOOL Jamb nut B goes on the inside DO NOT over tighten Once secure install silicone washer A over jamb nut This serves as the seal between the oil filter wall and OIL FILTER ACCESS TOOL assembly a Figure 2 Piercing Quick Connect A SILICONE WASHER Coupler Assembly B JAMB NUT C INTERNAL STAR LOCK WASHER D PIERCING QUICK CONNECT COUPLER E MALE CONNECTOR FITTING unt Functional Description continea D PIERCING QUICK CONNECT COUPLER Pierces the oil filter wall Female coupler for gauge hose assembly E MALE CONNECTOR FITTING Connects gauge hose assembly to piercing quick connect coupler F 1 8 27 NPT STREET ELBOW 90 Enables gauge hose assembly to hook up in tight places that require a 90 degree elbow G 1 8 27 NPT STREET ELBOW 45 Enables gauge hose assembly to hook up in tight places that require a 45 degree elbow H SILICONE WASHER Serves as seal between the oil filter wall and OIL FILTER ACCESS TOOL 3 16 RUBBER CAP Use rubber cap to seal the male connector from unwanted oil leakage when storing gauge hose assembly Tool Set Up TO OPEN OIL FILTER ACCESS TOOL POTENTIAL
7. unt Contents an Safety Information Functional Description Tool Set Up ENGINE OIL PRESSURE GAUGE Test Procedure Maintenance OIL FILTER ACCESS TOOL PINKT28 Waranty Parts List KT28BX 001 KT28GHB 001 IKT28G100 001 KT28H001 3 K1T28B 001 KT280FAT 001 1 4 Elbow Key KT28EK 001 Piercing Quick Connect Couplet IKT28PQCC 001 Male Connector Fitting IKTMCF 001 1 8 27 NPT Street Elbow 90 KT28SE 90 1 8 27 NPT Street Elbow 45 KT28SE 45 Silicone WaShel sssscessssssesseeeeeeeesees KT28SW 001 3 3 16 Rubber Cap IKT28RC 001 2 Instruction Manual KT28IM 001 TPR1 Division TPR 2331 W Hampden Ave 130 Englewood CO 80110 303 781 9449 www tpr1 com any KT28 LPR ENGINE OIL PRESSURE GAUGE Safety Information continued OIL FILTER A CCESS TOOL RISK OF ENTANGLEMENT 7 EQUIPMENT CLEAR OF MOVING PARTS Safety Information oe a eR IMPORTANT SAFETY INSTRUCTIONS CAUSE INJURY This manual contains important safety and operating instructions for the TPR1 ENGINE OIL PRESSURE GAUGE OIL FILTER ACCESS TOOL Refer to the information in this manual often for safe operation RISK OF BURNS DO NOT TOUCH HOT ENGINE COMPONENTS READ ALL INSTRUCTIONS AVOID CONTACT WITH HOT ENGINE OIL HOT COMPONENTS CAN CAUSE INJURY Read understand and follow all safety messages and instructions in this manual and on the test equipment Safety messages in this section of the manual contain a signal word a one to three part
Download Pdf Manuals
Related Search