COMMANDER 950 - Holley Performance Products
Contents
1. COMMANDER 950 TBI HARDWARE INSTALLATION MANUAL NOTE These instructions must be read and fully understood before beginning installation If this manual is not fully understood installation should not be attempted Failure to follow these instructions including the pictures may result in subsequent system failure TABLE OF CONTENTS TOUINTRODUCTON 22 see ar a a a GE 2 2 0 GHOOSING THE RIGHT SYSTEM zes ze Leere ae 3 3 0 WARNINGS NOTES AND NO UIC Bo 2a ee ee ee ea ne ee age 3 40 PARTS IDENTIFICATION ee o o e re 4 5 0 ADDITIONAL ITEMS REQUIRED FOR INSTALLATION 0 0 0 cecccccecccecseeeeeeeeeeeeeeeeeeseeeeeeseaeeeeseeeeeseeeeeeseaeeeeseseeeeesaaeeesseeeeeeas 8 6 0 TOOLS REQUIRED FOR INSTALLATION Saaier Besen Ep A oe i iad te 8 7 0 REMOVAL OF EXISTING FUEL SYSTEM Zaun ee 8 8 0 GOMMANDE 950 SYSTEM INSTALLATION Sa as ae a 9 Win ee ee erste ee ei ee 9 8 2 Th ottle Connections zu ee A A EA a 9 82 Vacuum Line CORHEElons areas nen ee en enge 10 OA FVel PUmp Installalonzs2 SA edu ace ocd esd eee ass eee assets 11 8 5 Dal an Stall AON 22 2 a RR Russel 12 aba IO AA el Ue o E ne eee ee See ee een ee oe ee ene ene 13 o nro UES OC UNS i MET pe ete aa aia ta cian 13 8 8 Relurm Line Ihstallationze 2 20 A A A wa goes eek eg ok x ah Senet a acetate ee 13 8 9 Relurmio TELE LEAL SY SUA Vacs saccade a et Else ee 14 9 10 Inlet Fuel Eme asta sp a drs ees ie di ii estes 14 0 11 Oxygen sensor Installation aussi ii 14 8 11 1 Oxy2. WARNING Use of some RTV silicone sealers will destroy the oxygen sensor used with this product Ensure the RTV silicone sealant you use is compatible with oxygen sensor vehicles This information should be found on the oxygen sensor package 2 0 CHOOSING THE RIGHT SYSTEM To ensure that you have purchased the correct COMMANDER 950 kit for your application check to be sure that the kit you purchased is listed beside your engine s horsepower For best results in the event of an application overlap the correct kit choice is the one that the engine horsepower is more centered in the application For example if your engine is rated at 275 hp look at the chart below you will notice that there are 2 kits that could fit your application 275 hp is near the upper limit of Kit 950 23S 275 hp is more centered in the horsepower range of Kit 950 22S The correct choice would be one of the kits listed in the 225 to 400 horsepower range HORSEPOWER KIT PART NUMBER ho 0 Roo 01018 NP ne 950 235 COMMANDER 950 TBI 650 CFM 229 AU UND er wadaros os ornedoeevateneseseces s 950 225 COMMANDER 950 TBI 700 CFM 3992300 NP aaa 950 215 COMMANDER 950 TBI 900 CFM 3 0 WARNINGS NOTES AND NOTICES WARNING For the safety and protection of you and others the installation adjustment and repair must be performed only by a trained mechanic having adequate fuel system experience It is particularly important to remember one of the very basic principles of sa
3. 30 psig fuel gauge are needed Screw the gauge into the center of the tee fitting Attach the short length of hose to one end of the fitting Attach the free end of this hose to the throttle body fuel return fitting Attach the return fuel hose to the remaining side of the tee fitting Pressure Port Plug Inlet or Fuel Pump Side WARNING Ensure there is a fuel filter between the fuel tank and pump s If one must be added use Holley replacement filters only 8 11 Oxygen Sensor Installation 8 11 1 Oxygen Sensor Function Theory and Use The COMMANDER 950 allows the user to operate their engine in a closed loop fuel management mode using the oxygen sensor The oxygen sensor monitors the exhaust gases and outputs a voltage that corresponds to the fuel air mixture The 14 range of voltage output from the oxygen sensor is 0 0 to 1 0 volts A lean air fuel mixture gives a lower oxygen sensor output voltage while a rich air fuel mixture gives a higher oxygen sensor output voltage The stoichiometric or chemically perfect air fuel mixture gives an oxygen sensor output of approximately 0 5 volts The engine ECU reads this output from the oxygen sensor and adjusts the fuel delivery to maintain a stoichiometric fuel air mixture Most automobiles both currently and for the past 20 years are using oxygen sensors to monitor the engine fuel air mixture This is done primarily to improve engine emissions It also gives the advantage of maintaining a s
4. Standard wrench set e Small blade screwdriver e 5 32 allen wrench e Medium blade screwdriver e 2 Phillips screwdriver e Digital Volt Ohm meter e Drill and assorted bit sizes e Hole saw 2 e Terminal crimping tool e Engine tachometer e 10 adjustable wrench e Utility knife e Factory Service Manual e Windows compatible laptop PC for your vehicle e An assistant is necessary for some installation and adjustment procedures and should be present for safety reasons 7 0 REMOVAL OF EXISTING FUEL SYSTEM I Disconnect the battery and remove the air cleaner 2 Before disconnecting any vacuum hoses it is a good idea to sketch out the vacuum hose routing Using masking tape and a permanent marker mark all the vacuum hoses vacuum sources and ports before removing the old fuel delivery system 3 Remove and discard the fuel line that connects the fuel delivery system from the fuel pump This will not be needed in the installation 4 Disconnect and plug the inlet fuel line that runs from the gas tank to the fuel pump This will prevent fuel spillage and foreign matter or dirt from entering the fuel line DANGER BEFORE DISCONNECTING OR REMOVING FUEL LINES ENSURE THE ENGINE IS COLD DO NOT 8 SMOKE EXTINGUISH ALL OPEN FLAMES AN OPEN FLAME SPARK OR EXTREME HEAT NEAR GASOLINE CAN RESULT IN A FIRE OR EXPLOSION CAUSING PROPERTY DAMAGE SERIOUS INJURY AND OR DEATH 5 The fuel delivery system can now be removed Holley recomm
5. in the figure to the right The extension lever length can be adjusted using the four sets of holes Attach throttle linkage and have an assistant get in the vehicle and fully actuate the throttle controls Make the necessary adjustments to the throttle linkage to ensure that the throttle plates are vertical when the throttle control is wide open Work the throttle linkage back and forth several times to ensure it operates smoothly with no binding or sticking Extension Bracket attached using Two fillister head screws Attach ball stud in remaining hole in bracket DANGER STICKING THROTTLE MAY RESULT IN UNCONTROLLED ENGINE OR VEHICLE SPEED THIS COULD CAUSE PROPERTY DAMAGE PERSONAL INJURY OR DEATH A STICKING THROTTLE MAY BE CAUSED BY IMPROPERLY INSTALLED THROTTLE CABLES LACK OF CLEARANCE FOR ANY OF THE THROTTLE LINKAGE OR BY A BINDING THROTTLE LINKAGE CHECK ALL THROTTLE CABLES FOR PROPER INSTALLATION AND ALIGNMENT AND ACTUATE THE THROTTLE TO CHECK FOR ANY POTENTIAL BINDING OR CLEARANCE PROBLEMS REPAIR ANY PROBLEMS BEFORE CONTINUING Locate the 14 28 throttle stud from the parts provided and attach to the throttle lever with the nut provided Connect the accelerator linkage to the throttle stud on the throttle body If the vehicle is equipped with an automatic transmission connect the transmission kickdown rod to the linkage on the throttle body The transmission kickdown may have to be adjusted Follow the vehicle manufacturer s
6. 1 to 1 the front and rear plates will open at the same time NOTE The software must be set differently depending on the linkage type Perform the following depending on the type 1 to 1 Linkage For most efficient operation the rear injectors should be shut off at idle and very light throttle This ensures that the pulse width is not too low during very low fueling demands To do this obtain the TPS value at idle Add 20 to this number and enter it as the TBI Switch 2 4 value under the Engine Parameters screen Enter 5 for the TBI Switch Hysteresis value Both of these values can be changed to optimize each particular combination Progressive Linkage For progressive linkage the rear injectors must be shut off until the rear throttle plates start to open With the key on and the engine off open the throttle plates until the rear plates start to open Open the throttle slightly more at least 10 TPS units over when the rear plates just start to open You want the rear plates to be slightly open before the injectors turn on Look at the position of the TPS at this point on the computer Enter this value as the TBI Switch 2 4 value under the Engine Parameters screen A good value for the TBI Switch Hysteresis is 5 This means that when the TPS goes 5 units below the TBI Switch 2 4 value the rear injectors turn back off The wiring harnesses should be wired such that only the front two injectors will op
7. TH 6 If using existing fuel lines inspect and replace any hose clamps or fuel line showing ANY sign of aging If you are not using existing fuel lines you will need a fuel line routed to the engine compartment and COMMANDER 950 throttle body Use a 3 8 steel fuel line available at any auto parts store All steel fuel line must meet SAE J526 standards DANGER FAILURE TO USE STEEL A FUEL LINE THAT MEETS SAE J526 STANDARDS COULD RESULT IN FUEL LEAKS A FUEL LEAK MAY RESULT IN A FIRE OR EXPLOSION HAZARD WHICH COULD CAUSE SERIOUS INJURY OR DEATH DANGER TAKE PRECAUTIONS TO ENSURE THAT ALL FUEL LINE ROUTINGS ARE AWAY FROM HEAT SOURCES SUCH AS THE ENGINE OR EXHAUST PIPES A FIRE OR EXPLOSION HAZARD COULD CAUSE SERIOUS INJURY OR DEATH 11 DANGER RIGID FUEL LINE TUBING SHOULD BE USED FOR UNDER VEHICLE RUNS SUCH AS ALONG VEHICLE FRAME RAILS OR UNDER FLOOR PANS FAILURE TO DO SO IS A POTENTIAL FIRE OR EXPLOSION HAZARD WHICH COULD CAUSE SERIOUS INJURY OR DEATH 7 Anchor all fuel lines securely to solid chassis members at 1 foot intervals using rubber coated steel clamps Use of only approved steel fuel line tubing will afford maximum fuel line protection against road hazards and premature wearing due to flexing temperature extremes road salt weather etc 8 5 Dual Tank Installation The following are special instructions for vehicles equipped with dual fuel tanks Holley COMMANDER 950 fuel injection systems require a fuel return l
8. dy have a return line to the fuel tank that can be utilized If a return fuel line must be installed a minimum size of 5 16 I D is recommended DANGER DO NOT USE THE VAPOR CANISTER LINES AS A FUEL RETURN LINE POSSIBLE FUEL LEAKS MAY CREATE A FIRE OR EXPLOSION HAZARD CAUSING SERIOUS INJURY OR DEATH WARNING Use only approved steel fuel line The return fuel line should enter the fuel tank at the fuel level sending unit flange or at the filler neck The filler neck or sending unit must be removed from the 13 tank to perform this operation DANGER PROPER INSTALLATION OF THE FUEL RETURN LINE MAY NECESSITATE COMPLETE REMOVAL OF THE FUEL TANK THIS WORK SHOULD BE DONE BY A FUEL TANK SPECIALIST WHO REGULARLY DOES THIS WORK AND IS FAMILIAR WITH SAFETY REGULATIONS AND PRECAUTIONS NECESSARY TO DO THIS WORK IF A PERSON ATTEMPTS THIS WORK WHO IS NOT FAMILIAR WITH THE SAFETY REGULATIONS AND PRECAUTIONS AN EXPLOSION HAZARD MAY RESULT CAUSING SERIOUS INJURY OR DEATH 8 9 Return to fuel tank system 1 Install a 5 16 return line hose from the 5 16 return fitting in the throttle body to a fitting in the fuel tank Use the supplied hose clamps to ensure that the fuel line fittings are tight at both ends of the hose The system tuning and checkout process requires a fuel pressure gauge be installed in the return line system This is a good time to consider how this pressure gauge will be installed There are two plugs in the t
9. ends removing the mechanical fuel pump if so equipped and blocking off the fuel pump mount using the provided fuel pump block off plate The COMMANDER 950 system kit includes a block off plate that will fit small and big block Chevrolet and Chrysler engines If the block off plate does not fit your engine a block off plate may have to be purchased from a local performance parts supplier 6 Ifrequired replace the intake manifold at this time Proceed to step seven if this is not required A 4 BARREL STOCK OR AFTERMARKET INTAKE MANIFOLD IS REQUIRED FOR THE INSTALLATION OF THE HOLLEY COMMANDER 950 TBI system 7 Place clean shop towels or rags into the manifold opening to prevent dirt or debris from entering the engine Keep exposed ends of the vacuum and fuel lines free from dirt WARNING Failure to cover the intake opening with a clean towel could result in dirt or debris entering the engine Dirt or debris in the induction system can cause engine damage which may necessitate in a complete engine overhaul 8 Remove all traces of the old gasket material from the TBI mounting flange DO NOT gouge the intake manifold sealing surface during removal of old gasket material Failure to remove all traces of the old gasket material will result in vacuum leaks that will be difficult to detect later Sealing flanges must be clean and dry before installation 9 Remove the shop towels from the intake and vacuum out the intake channel to ensure no dirt
10. erate below the TBI Switch 2 4 value The back two should turn on after the programmed TPS setting is reached Verify that the front two injectors are operating at idle If they are not extremely poor operation will result Idle Fuel Pulse Width Ideally the injector pulse width at idle should not be below 1 7 milliseconds ms This value is seen on the data monitor If the value is less than this the fuel pressure can be lowered This allows for the pulse width to be increased to a value above 1 7 ms NOTE For wiring harness installation and tuning information please see the supplied additional manual Copyright 2001 Holley Printed in U S A Performance Products 199R 10179 1 Date 01 09 01 16
11. fety fuel vapors are heavier than air and tend to collect in low places where an explosive fuel air mixture may be ignited by any spark or flame resulting in property damage personal injury and or death Extreme caution must be exercised to prevent spillage and thus eliminate the formation of such fuel vapors WARNING This type of work MUST be performed in a well ventilated area Do not smoke or have an open flame present near gasoline vapors or a explosion may result 4 0 PARTS IDENTIFICATION ITEM DESCRIPTION QTY SERVICE PART 1 TBI Assembly 650 CFM Complete 1 534 171 TBI Assembly 700 CFM Complete 1 534 172 TBI Assembly 900 CFM Complete Commander 950 ECU Commander 950 Software Commander 950 TBI Wiring Harness Commander 950 Communications Cable Fuel Pump Fuel Pump Clamp Metal Fuel Filter Plastic Fuel Filter Fuel Filter Clamp Fuel Pump Block Off Plate amp Gasket Oxygen Sensor MAP Sensor Coolant Temperature Sensor Air Cleaner Adapter Air Cleaner Gasket Distribution Ring Flange Gasket Manifold Flange Studs Heat Insulator Gasket Oxygen Sensor Weld Ring 40 AMP Relay Throttle Bracket Throttle and Cruise Control Stud Throttle Lever Ball Throttle Lever Bracket Throttle Lever Shipping Spring Throttle Lever Stud Transmission Kickdown Stud Hose Clamp Grommet Assorted Parts amp Terminals Cable Ties Silicon Grease Tube Cap Lockwasher 1 4 28 Nut 5 16 24 Nut 5 16 Vacuum Line Fuel Pump wiring Harne
12. gen Sensor Function Theory and Use occconccccconnncococonoconcnnocononcnnncnnncnncnnononnnonnnrnnornnnnnrornnnnnnnnrnnorannnnnnananennns 14 8 11 2 Oxygen Sensor Mounting Procedure cccccecccccseeeccceseecceeececceececseueeeseeeecsaecssaueeeseueeeessueeeeessageeesseeeessaesessgeessas 15 1 0 INTRODUCTION Holley Performance Products has written this manual for the installation of the COMMANDER 950 TBI fuel injection system This manual contains the information necessary for the hardware installation Please read all the WARNINGS NOTES and TIPS as they contain valuable information that can save you time and money It is our intent to provide the best possible products for our customer products that perform properly and satisfy your expectations Should you need information or parts assistance please contact our technical service department at 1 270 781 9741 Monday through Friday 7 a m to 5 p m Central Time By using this number you may obtain any information and or parts assistance that you may require Please have the part number of the product you purchased when you call NOTE This manual is for the hardware installation of a Holley Throttle Body Fuel Injection System and instructions specific to it Instructions on wiring harness installation software operation sensor operation and tuning is contained in the supplied additional manual 199R 10149 2 NOTE A laptop computer with a serial communications port is required fo
13. hrottle body one in the return line area and one in the supply side area See the figure below for the pressure port plug locations These make a very good location to install a pressure gauge Attach a section of 5 16 hose to the outlet of the throttle body and secure with a hose clamp Run the other end to either the fuel tank or the inlet of the pump at the tee fitting as previously discussed in earlier text Secure with a hose clamp RETURN LINE NOTE The return line pressure should be as close to 0 zero as possible The fuel pressure should be no higher than 3 psi 8 10 Inlet Fuel Line Installation 1 Route a 3 8 hose from the COMMANDER 950 electric fuel pump outlet to the metal fuel filter inlet Then install a 3 8 hose from the filter outlet to the TBI inlet The fuel line connection p Plug Return Side on the left side of the throttle body or linkage gt side is the connection for the supply line The remaining fuel line connection on the TPS side Return Line of the throttle body is for the return fuel line to Fuel Tank Properly secure all hoses with hose clamps 2 If you plan to install fuel pressure gauges do so at this time If you do not plan to install fuel pressure gauges a temporary gauge will have ng to be installed on the return fuel line To install a ah a temporary gauge to the return fuel line a 7 Pump short length of 3 8 1 D fuel hose a tee fitting and a 0
14. ine and in dual tank applications the fuel must be returned to the tank from which it was drawn The items listed below are recommended to properly install your COMMANDER 950 TBI system on a dual tank vehicle A separate fuel pump and filter for each tank will be necessary Holley offers these items in a kit part number 534 37 Item Part Number Selection valve 42 149 Valve Connector 42 203 Toggle switch 34 576 Relay 534 26 Fuel pump 512 103 10 amp in line fuse Fuel filter 562 3 This is a recommended list and except for the fuel pump equivalent parts may be substituted In addition fuel hose clamps 18 gauge wire and assorted terminals will be needed The selection valve recommended switches tanks by reversing the polarity of the D and E terminals Many trucks equipped with dual tanks already have this type of selection valve along with the associated hardware 1 Mount the selection valve in a protected location close to the existing fuel lines and near the fuel tanks Position the valve so the side with the four hose nipples points toward the fuel tanks Mount the fuel pumps along the fuel supply lines and next to each fuel tank Fuel filters Holley Part Number 562 3 MUST be located between each tank and pump Make sure pump inlets point toward the tanks See FIGURE below WARNING The supply and return hoses from the same tank must be connected next to each other on the selection valve 2 All hoses should be sec
15. lled between the fuel tank and the fuel pump inlet The purpose of this filter is to protect the fuel pump from particles of dirt or other foreign material The filter should be installed with the arrow on the filter pointing in the direction of the fuel flow Secure the ends of the fuel lines with hose clamps 8 7 Throttle Body Fuel Filter The fuel filter that is included with the COMMANDER 950 TBI system should be installed between the electric pump outlet and the inlet fitting of the TBI Position the filter so the fuel hoses can be routed without kinks or sharp bends The filter should be installed with the arrow on the filter pointing in the direction of the fuel flow Secure the ends of the fuel lines with hose clamps Conveniently mount the fuel filter and clamp assembly using the hole provided in the clamp WARNING Ensure both filters are installed in the proper direction A flow direction arrow is stamped on the side of the filter to indicate the direction of fuel flow Failure to do so will result in a system malfunction DANGER TAKE PRECAUTIONS TO ENSURE ALL FUEL LINE ROUTINGS ARE AWAY FROM HEAT SOURCES SUCH AS THE ENGINE OR EXHAUST SYSTEM A FIRE OR EXPLOSION HAZARD COULD CAUSE PROPERTY DAMAGE SERIOUS INJURY AND OR DEATH 8 8 Return Line Installation The Holley COMMANDER 950 TBI system requires a return fuel line to the fuel tank Some late model vehicles that were originally equipped with a throttle body injection system may alrea
16. manifold flange studs with the IAC motor facing the front of the vehicle and the regulator fuel connections towards the rear of the of the vehicle 3 Tighten the throttle body down in a criss cross pattern being careful not to over tighten Proper torque is 5 7 ft Ibs WARNING Over tightening the TBI manifold flange hold down nuts may result in a warped or cracked throttle body The TBI hold down nuts should be tightened down progressively in a criss cross pattern to 5 7 ft Ibs to prevent leaks and avoid causing damage to the throttle body A TBI that has been damaged due to negligence of the owner will void the warranty 8 2 Throttle Connections 1 Measure the length of the throttle lever arm on the NO I carburetor removed from the vehicle Compare the length of the existing throttle lever arm with the one on the COMMANDER 950 throttle body If the two throttle lever arms are similar in length within Y of each other the throttle lever arm hole on the COMMANDER 950 throttle body can be used without the extension bracket Use the throttle lever arm extension bracket if the old throttle lever arm is significantly longer than the new throttle lever arm Before installation of the bracket check the diameter of the throttle cable stud Some systems may use a Y stud that will require drilling of the appropriate hole in the extension bracket to a Y diameter Attach the extension bracket using two fillister head screws as shown
17. mpetent exhaust shop is able to perform this task at a minimum cost WARNING Use only unleaded fuel when operating an oxygen sensor Use of leaded fuels will destroy the oxygen sensor and will result in incorrect exhaust gas oxygen content readings WARNING Use of some RTV silicone sealers will destroy the oxygen sensor used with this product Ensure the RTV silicone sealant you use is compatible with oxygen sensor vehicles This information should be found on the oxygen sensor package 1 Locate a position for the oxygen sensor as close to the engine as possible If your vehicle has catalytic converters the oxygen sensor MUST be located between the engine and the catalytic converters A Me ae PRA SS EOS NOTE The oxygen sensor should be mounted in such a way that the condensation in the exhaust tubing will not enter the sensor Mount the O sensor in the upper half of the exhaust tubing with the angle x shown above being greater than 10 The picture above indicates that the sensor can be mounted on either side of the exhaust tubing 2 Drill a 7 8 hole in the location picked for the sensor Weld the threaded boss into the 7 8 hole Weld all the way around the boss to insure a leak proof connection Install the oxygen sensor into the threaded boss and tighten securely It is a good idea to add anti seize to the threads to aid in removal 15 3 On vehicles equipped with an AIR pump the oxygen sensor must be m
18. or debris is left in the intake system Place a shop towel over the entire intake opening until you are ready to install the new COMMANDER 950 TBI 8 0 COMMANDER 950 SYSTEM INSTALLATION 8 1 Throttle Body NOTE A 4 barrel intake is required for the installation of the Holley COMMANDER 950 TBI system NOTE Some GM and Chrysler engines require the use of a manifold adapter Holley Part Number 17 6 This adapts the spread bore carburetor manifold to the Holley square flange 1 Install the heat spacer between the manifold and the 4 barrel throttle body injection unit Check for sufficient thread engagement of the throttle body hold down studs and nuts It may be necessary to purchase and install longer studs in the manifold for proper nut engagement Gasket sealant may be used to ensure that no vacuum leaks occur NOTE If using a heat spacer the flange gasket is not required DANGER CHECK FOR PROPER CLEARANCE BETWEEN ENGINE COMPONENTS SUCH AS THE DISTRIBUTOR COIL ETC AND THE THROTTLE BODY IF ANY INTERFERENCE IS FOUND CORRECT THE CONDITION BEFORE CONTINUING FAILURE TO DO SO CAN RESULT IN DAMAGE TO ENGINE COMPONENTS OR THE THROTTLE BODY DANGER CHECK FOR PROPER CLEARANCE BETWEEN THE AIR CLEANER AND THE ENGINE COMPARTMENT COVER HOOD IF ANY INTERFERENCE IS FOUND CORRECT THE CONDITION BEFORE CONTINUING FAILURE TO DO SO CAN RESULT IN DAMAGE TO THE COMPARTMENT COVER OR ENGINE COMPONENTS 2 Place the throttle body in position over the
19. ounted before the AIR injection into the exhaust or the AIR pump must be disconnected Holley recommends that if the AIR is injected into both exhaust manifolds mount the oxygen sensor into the pipe immediately after the exhaust manifold Disconnect the AIR pump tube from the exhaust manifold and plug both ends Check with local ordinances for the legality of this procedure in your area WARNING Failure to disconnect the AIR pump or locating the oxygen sensor downstream from AIR injection will result in an extremely rich mixture which could cause driveability problems and severe engine damage WARNING It is important that the distribution ring is properly installed and fastened to the throttle body Failure to do so will cause an inadequate seal between the throttle body and air cleaner and may be a fire hazard in the event of a backfire Fire hazard can result in property damage serious injury and or death 9 0 THROTTLE BODY INJECTION SPECIFIC TUNING The throttle body injection TBI systems have several items to note The factory should have preset the fuel pressure at 21 psi This should be checked if possible before the tuning is performed The injectors can operate down to 10 psi The pressure can safely be raised above 21 psi Next check the throttle body linkage to determine if it is progressive or a 1 to 1 linkage If it is progressive the front plates will open first After some travel the rear plates will open If the linkage is a
20. ous temperature at the sensor is 1500 F Most engines idle with an EGT of 800 1100 F near the cylinder head exhaust port If the sensor is mounted far away such as in the collector of long tube headers the temperature may drop to as low as 300 F at idle If the oxygen sensor attempts to control the air fuel ratio when the EGT it sees is between 300 and 600 F the problems mentioned above can occur It is recommended to mount the oxygen sensor as close as possible where one bank of cylinders merge together If an OEM mounting location is available use it With stock cast iron manifolds the sensor can be mounted in the exhaust pipe right after the cast iron manifold in the exhaust pipe or possibly in the end of the manifold itself If the vehicle has shorty headers the sensor can be mounted in the collector of the headers If the vehicle has long tube headers the sensor can be mounted in the collector but the temperature will likely be too low at idle for proper operation A fix for this if proper closed loop operation does not occur is to run open loop at lower engine speeds until enough heat is available for proper operation This is programmable in the ECU Other factors such as camshaft specifications will effect how well closed loop operation occurs at low engine speeds and loads 8 11 2 Oxygen Sensor Mounting Procedure NOTE The oxygen sensor boss should be installed by someone with experience in welding exhaust systems Any co
21. procedure for the correct adjustment procedure NOTE On late model GM and Ford overdrive transmissions the transmission electronic lockup must be changed to a mechanical lockup by a competent transmission shop Failure to do so will result in premature transmission failure NOTE On Chrysler vehicles a lever extension will be needed Holley Part Number 20 7 Van applications may require the use of throttle lever extension Holley Part Number 20 14 4 Attach throttle linkage and throttle return spring Have an assistant get in the vehicle and fully depress the accelerator pedal Make the necessary adjustments to the throttle linkage to insure that the throttle reaches wide open position when the accelerator is depressed Work throttle linkage back and forth several times to insure it operates smoothly with no binding or sticking DANGER FAILURE TO ATTACH THE THROTTLE RETURN SPRING OR A STICKING THROTTLE MAY RESULT IN UNCONTROLLED ENGINE OR VEHICLE SPEED WHICH COULD CAUSE PERSONAL PROPERTY DAMAGE SERIOUS INJURY OR DEATH 8 3 Vacuum Line Connections 10 1 Install vacuum hoses to the appropriate port on the throttle body Use the diagrams made during removal of the existing fuel system to locate the correct port The vacuum ports of the throttle body are labeled in the figure below 8 4 Fuel Pump Installation 1 Do not mount the fuel pump higher than the lowest point of the fuel tank 2 Mount the fuel pump as close as pos
22. r the installation and tuning of this system WARNING The COMMANDER 950 systems consist of anumber of sophisticated components Failure of any one component does not constitute nor does it justify warranty of the complete system Individual service items are available for replacement of components If assistance is required or if you need further warranty clarification you can call Holley Technical Service at the number shown above WARNING To preserve warranty these instructions must be read and followed thoroughly and completely before and during installation It is important that you become familiar with the parts and the installation of the COMMANDER 950 system before you begin Failure to read and understand these instructions could result in damage to COMMANDER 950 components that are not covered by the warranty and could result in serious personal injury and property damage WARNING For closed loop systems using an oxygen sensor use only unleaded fuels with this product Use of leaded fuels will destroy the oxygen sensor and will result in incorrect exhaust gas oxygen readings and improper fuel delivery Failure to follow these directions does not constitute the right to a warranty claim WARNING Failure to follow all of the above will result in an improper installation which may lead to personal injury including death and or property damage Improper installation and or use of this or any Holley product will void all warranties
23. sible to the fuel tank 3 Make sure fuel tank is properly vented DANGER NEVER GET UNDER A VEHICLE SUPPORTED ONLY BY AJACK SERIOUS INJURY OR DEATH CAN RESULT FROM VEHICLES FALLING OFF OF JACKS BEFORE WORKING UNDERNEATH A VEHICLE SUPPORT SOLIDLY WITH JACK STANDS 4 Mount the electric fuel pump as close to the fuel tank outlet as possible with the bracket provided Mounting the fuel pump in this manner will insure that the pump will prime easily and purge fuel vapors in the TBI quickly to ensure faster Starts DANGER TAKE PRECAUTIONS TO ENSURE THAT ALL FUEL LINE ROUTINGS ARE AWAY FROM HEAT SOURCES SUCH AS THE ENGINE OR EXHAUST PIPES A FIRE OR EXPLOSION HAZARD COULD CAUSE SERIOUS INJURY OR DEATH DANGER ENSURE THAT THE FUEL PUMP MOUNTING LOCATION WILL NOT INTERFERE WITH ANY UNDER THE VEHICLE COMPONENTS ESPECIALLY AT THE EXTREME LIMITS OF THE SUSPENSION TRAVEL A FIRE OR EXPLOSION HAZARD COULD CAUSE SERIOUS INJURY OR DEATH Fuel Tank Metal Fasc Fe 5 Connect the pump to the tank using 3 8 1 D fuel hose Connect the outlet of the pump to the steel line which runs to the front of the vehicle with 3 8 I D fuel hose depending on the diameter of the steel fuel line All fuel hoses used must meet SAE J30 performance standards DANGER FAILURE TO USE A FUEL HOSE THAT MEETS SAE J30 STANDARDS COULD RESULT IN FUEL LEAKS A FUEL LEAK MAY RESULT IN A FIRE OR EXPLOSION HAZARD WHICH COULD CAUSE SERIOUS INJURY OR DEA
24. ss TBI Service Parts Air Charge Temperature Sensor Fuel Injector 650 CFM Fuel Injector 700 CFM Fuel Injector 900 CFM Fuel Pressure Regulator Diaphragm Idle Air Control IAC Motor Throttle Position Sensor TPS Optional Parts GM Distributor Wiring Adapter Ford Distributor Wiring Adapter JK DD OO Pp A oS a 2 3 2 2 2 2 2 2 2 9 ame Se fA KS 934 173 934 120 534 144 534 146 534 140 512 105 N A 562 1 562 3 108 10 12 813 43 106 538 24 534 2 17 14 108 4 508 12 108 10 N A 108 12 534 49 534 26 N A N A N A N A N A N A N A N A N A 534 42 N A N A N A N A N A N A N A N A 534 46 522 81 522 80 922 43 512 1 543 105 943 29 534 138 534 139 T Pr E neo AAA Item 8 Item 10 Item 11 Item 12 Item 13 Item 14 Item 15 Item 16 Item 17 Item 18 Item 19 Item 20 Item 21 Item 25 Item 28 Item 29 Item 30 Item 31 Item 32 Item 34 Item 35 Item 36 Item 37 Item 38 Item 39 Item 40 Item 41 5 0 ADDITIONAL ITEMS REQUIRED FOR INSTALLATION e 3 8 fuel hose must meet SAE J30 e 5 16 fuel hose must meet SAE J30 e 5 16 steel fuel line must meet SAE J526 e 0 30 psi fuel gauge e Tee fitting for fuel gauge In addition to the above list the engine must be equipped with a four barrel intake manifold and the vehicle must be in good operating condition 6 0 TOOLS REQUIRED FOR INSTALLATION e
25. toichiometric fuel air mixture under varied operating conditions giving generally better engine performance and fuel economy Holley includes oxygen sensor feedback capability with the COMMANDER 950 system and recommends the user to use the oxygen sensor For most user applications better performance and fuel economy will be obtained by using the oxygen sensor In addition the oxygen sensor can make the tuning process much easier since the user can monitor the ECU functions as it adjusts the fuel to meet a stoichiometric fuel air mixture The mounting location of the oxygen sensor is extremely important for the proper operation of the engine The exhaust gas temperature EGT in the exhaust where the sensor is mounted is very important for proper closed loop operation If the EGT is too low two undesirable conditions can result First the ECU may sense that the O2 sensor is not up to proper temperature and will not activate closed loop operation Second the sensor could emit a false low voltage even if the air fuel ratio is rich The ECU will see this as a lean condition and add fuel to compensate in closed loop mode This makes the rich condition even worse which will lower the EGT and complicate the problem The lower the EGT the sensor sees the slower the sensor will react reducing the benefits of closed loop operation The minimum recommended temperature for reasonable closed loop operation is 800 F Fahrenheit at the sensor Maximum continu
26. ured with worm gear type clamps Avoid RETURN EINE sharp bends in the fuel lines o amp I Mount the double position double throw toggle switch along with the relay under the dash if the vehicle is not already equipped with this type switch Connect the electrical RETURN LINE FROM ENGINE wiring as shown in the FIGURE on the next page NOTE All wiring should be 18 gauge r or heavier automotive wire i fo that meets SAE J1560 par standards Wire the toggle switch as illustrated with one FUEL FILTER pair of terminals wired to ground and the other pair to a SWITCHING 12 volt power source through the relay and a 10 amp fuse The terminals on the plug in connector are labeled A F and should be wired to the following items A Fuel sending unit tank 1 B Fuel gauge at dash 12 Fuel sending unit tank 2 Fuel pump 2 12v and switch Fuel pump 1 12v and switch Not used nmU0 4 Plug the connector into the selection valve Double check all fuel and electrical connections to be sure they are installed properly Electrical connections should be insulated and sealed to prevent arcing and corrosion Check the operation of the selection valve when the COMMANDER 950 TBI system installation is complete TO FUEL GAUGE ee ee _ ee TANK 1 GREEN BLACK WIRE FROM FUEL PUMP RELAY PUMP 1 Wos A POSITION SWITCH LIA i 7 th CONNECTOR 000000 8 6 Fuel Pump Filter A filter MUST be insta
Download Pdf Manuals
Related Search