Home

Coca-Cola Marketing Machine

Contents

1. Check control board Problem Space to sales does not work properly when adding and deleting columns Troubleshooting A Check for bad connections or broken wires from select switch to control board Check control board Problem F2 motor power fuse 6 Amp blows when a given motor runs Troubleshooting Check motor for short B Check motor switch and motor wires for short Check motor Check the ballast lamps and lamp harnessing for broken backed out crossed wires Problem Board power fuse blows when supplving power Troubleshooting Check changer and interface harness B Check validator and interface harness Problem Flashing decimal point Troubleshooting Goto diagnostics e All columns shown to be jammed Check 6 Amp motor fuse F2 Select problem Enable problem check board Pb problem check board SIID SELECT PANEL DISPLAY Problem Plug in vender and 1 1 1 1 scrolls across display Troubleshooting Remove power to vender for one minute then power vender back up B Check for bad connections or broken backed out or crossed wires in select panel harness C Check top of door weld assembly for seal D Check control board 12 Problem Display shows LOC Troubleshooting only be accessed DEX or hand held Check control board 13 Problem Will not show vend price on display Troubleshooting A All vend prices on primary pri
2. indicating the new code is ready to be entered B Pressthe four 4 select buttons that are desired to be in the code As they are pressed the display will change to show the four 4 select buttons chosen Note Four 4 separate buttons must be used or the pattern will not be saved Note Only select buttons 1 through 9 may be used C Press the service switch The display will change back to ECNT To show the current count hold the four keys programmed for five 5 seconds The display will show historical total vends To view other data Press amp hold Select Button 1 Show historical total vends Press amp hold Select Button 2 Show list of prices and historical product counts that have occurred for those prices Press amp hold Select Button 3 Show interval product count for each selection Press amp hold Select Button 4 for five seconds Resets interval data COUNTERS RESET will scroll across display Press any select button greater than 4 will return the vender to normal operation Note There is a two 2 minute time out that will return the vender to normal vending mode Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu NF NOTE FACTOR for use with foreign note acceptors only Will only be present in menu if SET BILLS ONLY is programmed to BILLS YES Some foreign note acceptors that use pulsed signal to indicate the value of the note being accepted mus
3. s where shows the selections that are set for limited access To change limited access on any selection press and hold the desired select button until the message displayed is the desired limited access condition for that selection ENABLED SEL s Selection s displayed are on limited access DISABLED All selections are not on limited access Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu LIMITED ACCESS ON DAVS This function is used to set the davs of the week for limited access To view the limited access on davs condition press and let go of any select button The display will show ENABLED ON DAYS 6 Day of Week Sunday 1 Wednesday 4 Saturday 7 Monday 2 Thursday 5 Tuesday 3 Friday 6 To change limited access on days To Add Days Press service switch ADD will appear on display Press and hold any select button to scroll through days Release select button at desired day to turn on limited access Press service switch to complete limited access on days decision This must be done for each day to be added To Remove Days Press service switch ADD will appear on display Press service switch again DEL will appear on display Press and hold any select button to scroll through days Release select button at desired day to turn off limited access on that day Press service switch to complete limited access on days decision This must be done for each day
4. diagnostics and test 1 Will not take coins replace coin mech 2 Still will not take coins check connections and mech harness D Check for bad connections or broken backed out or crossed wires from validator changer to control board E With Mars 6510 Mdb mechs serialized 176xxxxxxxx that do not have a red dot on the coin mech check the coin mech F Check control board Problem Validator sometimes sets up credit and then steals bill Troubleshooting Check for proper interface harness B Check for bad connections or broken backed out or crossed wires from vend sold out harness C Check validator D Check control board Problem Accepts coins and displays but will not vend Troubleshooting Check coin mech Check for bad connections or broken backed out or crossed wires from validator changer to control board Check voltage supply 110 115AC at outlet D Check control board Problem Incorrect change paid back use correct change lamp stays on Troubleshooting Check control board Problem Cannot dump coins when CPO mode Troubleshooting Check for bad connections or broken backed out or crossed wires from changer to control board Check select switches and wiring Check coin mech Ensure you are not using Mars International Executive or NRI Simplex changers Check voltage supply 110 115AC at outlet Check control board Oe Problem stealing bills Trou
5. 804 905 32x x1 804 905 32x x1 804 905 32x x1 MARKETING SERVICE MANUAL ITEM DESCRIPTION uH Main Wiring Harness United States amp Mexico Fan Housing Assy Double Narrow 10A Control All Styles 10B Temperature Control Extension 045x5 125x6 671 18A Condenser Fan Shroud All Styles Relay 110V 60 Hz Domestic Models Embraco 1 351 605 Overload 110V 60 Hz Domestic Models TIMRT22AFZ 5598 FOR 1 3 HP Dryer All Styles 054 Outlet 4AXH7 Condenser All Styles B 1 3 HP Evaporator short CW01655 1 3 HP Capacitor Start Domestic 233 280MFD 115V 60 Hz Capacitor End Cap Bottom Hole Domestic Capacitor Assembling Bracket Domestic Cover Embraco 1 355 504 Short Domestic 1 3 HP Top Evaporator Cover FOR 1 3 HP 18B 18C E TEN Screw Phil 8 32 3 8 16 Screw Phil Pan Sems Washer 8 18 1 2 DIXIE NARCO INC DNCB 600E 79 Wide DNCB 501E DNCB 276E 72 Wide 72 Narrow 804 902 22 1 804 902 22 1 804 902 22x x1 609 044 00x x3 609 044 00x x3 295 040 1003 802 800 50x x1 624 000 01x x3 624 000 01x x3 624 000 01x x3 A eee 491 040 11 3 491 040 11 3 491 040 11 3 AAA OA AA 802 502 13x x1 802 502 13x x1 802 502 13x x1 E A A 802 502 10x x1 802 502 10x x1 802 502 10x x1 E ia 802 401 29x x1 802 401 29x x1 802 401 29x x1 A EPA SN 802 600 55x x1 802 600
6. 1 Kydex Door All Styles 801 903 34x x1 801 903 34x x1 801 903 34 1 164 000 04x x3 165 000 04x x3 165 000 04x x3 Protective Plate Right Cabinet gt N Screw Type F 1 4 20x5 8 900 302 01x x1 Screw Phil Pan 10 32x5 8 900 901 51x x1 gt Screw Phil Pan 8 18x1 2 900 301 98 1 Screw Phil 8 18x3 4 800 303 15x x1 Keps Nut 1 4 20 900 800 67 1 Lockwasher Shakeproof 5 8 1132 00 00 0551 900 700 89 1 Washer Shakeproof 4610 16 01 0551 900 700 62x x1 Carriage Bolt 1 4 20x5 8 900 303 12x x1 Pop Rivet Aluminum 1 4 900 100 43x x1 Pop Rivet Steel Zinc Plated 1 8 901 100 61x x1 Pop Rivet Aluminum 1 8 901 100 53x x1 Tinnerman Clip Fan Shroud C5207 014 3B 900 901 89x x1 7 Hole Plug Snap In 1 1 4 801 807 01x x1 Clamp Nylon 5 16 Black Heyco 3355 or Dennison 10159 900 901 79x x1 Clamp Nylon 1 2 Heyco 3328 900 901 80x x1 N 7 m 7 m 00 gt MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC 1 BLA A asuh LY IN Ga MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC CABINET AND VEND MECHANISM DESCRIPTION DNCB 600 DNCB 501E DNCB 276E Vend Motor Cover Assy AAA 8 ARO All Styles Vend Motor Assv Wide Single Price 609 070 60x x3 609 070 60x x3 NA 609 070 70x x3 609 070 70x x3 NA 801 809 80x
7. Height 2007mm 79 1 2 Width 940mm 37 1 16 Depth 737mm 30 1 2 Shipping Wt 331 730 lbs DNCB 501T Height 1829mm 72 Width 940mm 37 1 16 Depth 813mm 32 Shipping Wt 344 758 lbs DNCB 522T Height 1829mm 72 Width 940mm 37 1 16 Depth 813mm 32 Shipping Wt 305 672 lbs DNCB 600T Height 2007mm 79 1 2 Width 940mm 37 1 16 Depth 813mm 32 Shipping Wt 381 840 158 PRODUCT IDENTIFICATION The age of Dixie Narco products is determined the date code incorporated in serial number The vender serial number takes the form xxxx vvvvzz The first 4 digits xxxx identifv the specific vender The next 4 digits vvvv identifv the manufacturing run that the vender was built in The last two alpha characters zz identifv the quarter and the vear the vender was built The first alpha character identifies the quarter 1st quarter 2nd quarter 3rd quarter D 4 quarter The second alpha character identifies the vear 1995 U 1996 1997 1998 1999 2000 2 2001 510 CAN amp BOTTLE VENDER INSTALLATION 8 SET UP The SIID can and bottle vender is designed utilizing the latest technology featuring a highly sophisticated micro computer based control system The SIID Electronic Vender is designed to meet the growing need for accountability multi pricing programmability and system diagnostics in can vending equipment Along
8. Sow PAT Pan Sage Por 7 AAA ee Flat Washer B Delrin 040 thick 3 8 IDx5 8 OD MARKETING SERVICE MANUAL DIXIE NARCO INC HINGES AND ROLLER ASSV ITEM DESCRIPTION 1A Roller Main Door All Styles 1B Roller Pin All Styles Assy Top Hinge drop in pin E Models All Styles wass 17 74 10 Wami Top Hinge drop in pin E Models All Styles Top Hinge Spacer Hinge Bearing All Styles Bottom Hinge Sleeve All Styles Bottom Hinge Pin Bottom Hinge gt Screw Phil Pan Swage Form 8 32x3 8 Screw Machine Truss 10 32x1 2 Screw Self Tapping 1 4 20x5 8 gt gt UJ Keps Nut 1 4 20 Keps Nut Top Door Hinge 3 8 16 Hex Nut 5 16 28 Center w Flange 00 W top hinge drop in 0 Flat Washer Door Hinge Washer Flat 18 Gauge Flat Washer 14 Gauge 5 1 6 3 8 x7 8 Carriage Bolt 1 4 20x1 Carriage Bolt 1 4 20x3 4 Carriage Bolt 1 4 20x1 1 4 Carriage Bolt 1 4 20x5 8 top hinge drop in Retainer Roller Pin DNCB 600E 79 Wide 901 806 20x x1 900 502 19 1 900 502 19 1 501 72 Wide 901 806 20x x1 624 052 90x x3 624 052 90x x3 801 305 14 1 801 305 14 1 169 000 15 3 805 300 42x x1 900 502 64x x1 900 502 70x x1 900 502 70x x1 801 305 13x x1 801 305 13x x1 900 301 56x x1 900 201 14x x1 900 302 01x x1 900 800 67x x1 900 800 69x x1 900 801 02x x1 901 303 77x x1 900
9. 55x x1 802 600 55x x1 AAA AA 802 600 37x x1 802 600 37x x1 802 600 37x x1 WE NG 1 802 400 46 1 802 400 46 1 802 400 46 1 ae A 802 501 21 1 802 501 21 1 802 501 21 1 E A 802 501 18x x1 802 501 18x x1 802 501 18x x1 88381 802 501 87 1 802 501 87 1 802 501 87 1 isane e 802 501 86 1 802 501 86 1 si 609 050 06x x3 609 050 06x x3 900 301 56x x1 900 301 65x x1 802 800 50x x1 802 800 54x x1 615 050 14x x3 Screw Phil Pan Shoulder 8 18x17 32 900 301 98x x1 Screw Phil Pan 8 18x1 2 900 301 84x x1 28 Screw Machine Brass 6 32 1 4 900 201 44x x1 Speed Nut 900 800 85x x1 Lock Washer Split 3 8 Refrigeration Bolt 3 8 16x1 Pop Rivet Aluminum 1 8 901 100 53x x1 Screw Hex Head 8 36x3 8 900 301 69x x1 900 700 36x x1 900 400 44x x1 Screw Phil Flat 10 32x1 2 900 301 94x x1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION DNCB 600E DNCB 501E DNCB 276E 79 Wide 72 Wide 72 Narrow Tinnerman Clip Fan Shroud 900 901 89x x1 Tinnerman Clip 900 902 18x x1 Grommet Admiral B53351 901 806 77 1 902 100 26 04 Clamp Nvlon 3 4 3382BL 901 900 55x x1 112 Cable Tie 5 1 2 901 902 83 1 MARKETING SERVICE MANUAL DIXIE NARCO INC MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC ELECTRONI
10. 62 Select Panel Display U ben ag ENENG NENEKA NIN ENENG nea Pages 63 and 64 Refrigeration Parts Functions rre Pages 65 through 69 Refrigeration Cycler Page 70 Refrigeration Trouble Shooting Pages 71 through 76 Product Hot Compressor will not run I uu u Page 71 Product Hot Compressor starts but will not keep running Page 72 Product Hot Miscellaneous U Page 73 Product Cold But Not Cold Enough Compressor runs but won t cool product Page 74 Product Too Cold or Frozen Compressor runs too long or Page 75 Noisy Refrigeration Unit U uuu uu u Page 75 Excessive Condensate ia Page 76 EU TEE 77 Electrical E Eu Pages through WILLISTON SC Phone 800 688 9090 Phone 803 266 5000 FAX 803 266 5150 DNCB 168 Height Width Depth Shipping Wt DNCB 180 Height Width Depth Shipping Wt DNCB 276 Height Width Depth Shipping Wt DNCB 300 Height Width Depth Shipping Wt GENERAL INFORMATION VENDER SAFETV PRECAUTIONS Please read this manua
11. 700 83x x1 805 300 42x x1 169 000 15x x3 900 502 64x x1 900 700 08x x1 900 201 17x x1 900 201 56x x1 900 201 85x x1 800 303 19x x1 900 900 90x x1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC DIXIE NARCO INC COCA COLA MARKETING MACHINE SERVICE MANUAL 911814 12215 9 uep uonisod 989 9 81N6I4 i 7 a A al Jee Jaule 94 VS ping 9 4007 89 SM E 5 2 9129 SZ 5 o ui 7 ajen Jeulejoy Pug 99 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC CABINET INTERIOR ITEM DESCRIPTION DNCB 600E DNCB 501E DNCB 276E 79 Wide 72 Wide 72 Narrow Foam Cabinet Assy O A EAN ZA Stack a qt lo wp ox T Single Price Cars 600703605 SEMMI NA STD Cans 60270553 NA Single Price Bores 510070703 Lamae A STD Botes oma no A Stack Assv Single Shimming Stack Assy SID No Shimming Single Price 330 ml Can 4 deep 510 380 mi Can 4 deep Sack Sub Assy E I All Styles 610 070 40x x3 609 071 10x x3 615 070 10x x3 NA NA NA NA 330 ml Can 4 Deep Single Price 610 071 80x x3 609 074 50x x3 609 075 00x x3 Rear Spacer Assy Wide Column
12. All Styles 497 073 10x x3 498 071 30x x3 3B Rear Spacer Assy Narrow Column L 21 2020 All Styles 497 073 20x x3 498 071 40x x3 498 071 40x x3 SC Latch Spring Wide 901 700 88x x1 901 700 88x x1 907 700 86xx1 90170066 991700886 a Protective Plate Side F a sale ee A 5A Wire ae mama 5B Wire Gate Latch Lock 8 Guide All Styles 801 401 77x x1 801 401 77x x1 801 401 77x x1 5C Wire Gate Bracket Top All Styles 609 070 36x x3 609 070 36x x3 609 070 36x x3 SD Gate Label Canton P Eum All Styles 803 855 82x x1 803 855 82x x1 803 855 82 1 2 Clamp Nvlon Cable 1 2 rs All Styles 6A Mullion oo SSES SSES All Styles Mullion Gover All Styles 7A Breaker Strip Right A 492 020 04x x3 7B Breaker Strip Left HN O R 2 All Styles 7C Breaker Strip Top F AA A o E arr 493 020 06x x3 Leveling Leg 5 8 11x2 1 16 ree Mounting Bracket Rear ee 10 Cabinet Front Stiffener Plate was i MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION DNCB 600E DNCB 501E DNCB 276E 79 Wide 72 Wide 72 Narrow Trim Access Hole Stiffener All Styles 801 807 10x x1 801 807 10x x1 801 807 10x x1 Grommating No a M RI All Styles 801 809 93x x1 801 809 93 1 801 809 93
13. Electronics Standardization Committee developed and published a comprehensive set of data records relevant to the vending industry The SIID reports the portion of these related to this specific machine design The current list of records and their usage by the SIID follows DEX stands for Direct EXchange of data which means there is a hard wired connection between the two systems exchanging data This is done by inserting 1 4 inch phone plug on the portable data collection device in a jack mounted on the SIID Inserting the plug automatically initiates the exchange of data which takes several seconds No other machine functions are available while the exchange is taking place The operator is told that the exchange is taking place by the display of the message DEX IN PROGRESS Most of the data records are reported in both an interval and historical format The historical values represent a total of the values since the machine shipped from the factory The interval values are the data collected since the last time it was collected electronically The following types of audit data are accessible electronically Machine Identity Information Date and Time of Interrogation Cash Sales Summary Cash Input and Output Summary Product Sales Information Machine Configuration Events Door Openings Interrogations Programmable Access Limits Time of Day Discounts In addition to retrieving audit data every machine configuration parameter that ca
14. No cancel sale is allowed once minimum vend price is met or exceeded Press amp hold Select Button 2 94 Escrow to Select 4 The escrow condition is escrow to select with all dollar bills being stacked Cancel sale will return the deposit from the coin changer i e 4 quarters Press amp hold Select Button 3 51 Escrow to Select 1 The escrow condition is escrow to select with the last dollar bill that meets or exceeds maximum vend price being escrowed in the validator Cancel sale will return the held dollar bill and any amount over 1 will be returned from the coin changer Press amp hold Select Button 4 2 Escrow No Cancel The escrow condition is escrow no cancel with all bills stacked and no cancel sale allowed unless the vender is in exact change and the maximum vend price is exceeded Note Any money entered below the vend price cannot be returned Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu LANG LANGUAGE This function is used to set the language that will be used for display messages To display the current language selected press select button 1 To change the language selected press amp hold select buttons 1 and 2 simultaneously to scroll through the language menu Once the desired language is shown on the display let go of the buttons The display will then return to LANG English ENGL Spanish SPN Italian ITA Dutch DUT German GERM French F
15. Out Switch Harness SIID 7 Door Harness 9 Electronic CC 10 Electronic CC 11 12 13 Electronic without Sold Out Lights CC 11 12 13 Electronic with sold out lights 3 Display Harness E 4 Mech Harness 5 Cabinet Extension Harness ix 80 510 30 Motor Extension Harness ye GIID Sb 90 SIID S3D 7 Motor Harness SIID 7 DEX Harness External 1 Sold Out Light Harness 9 Select DIXIE NARCO INC PART NUMBER A 804 915 04x x1 804 917 01x x1 ESS 804 914 04x x1 804 913 89x x1 804 913 92x x1 804 916 07x x1 w 804 909 50x x1 804 909 78 1 804 913 96 1 804 913 95x x1 804 909 29x x1 804 915 03 1 804 917 02x x1 NE 804 913 97x x1 Ira 804 916 09x x1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC INNER DOOR ITEM DESCRIPTION PART NUMBER 2 3 4 4 5 5 5 6 A 1 Inner Door Assv ss 79 Wide 624 051 00x x3 72 Wide 624 051 10x x3 Inner Door Gasket 72 Narrow 624 051 20x x3 LA 79 Wide 801 804 07x x1 72 Wide 801 804 06x x1 72 Narrow 801 804 03x x1 Knob Kee 901 501 70 1 Discharge Frame Assv 801 809 16 1 B Discharge Frame Retainer KA 801 809 15 E 169 053 00x x3 Inner Door Bottom Hinge As
16. Selection Vends Sales His Vends His SIs 1 Cola 0 0 00 65 48 75 2 Cola 5 3 75 43 32 25 3 Cola 0 0 00 7 5 25 4 Apple Juice 0 0 00 18 13 50 5 Diet Cola 1 0 75 20 15 00 6 Diet Cola 4 3 00 41 30 75 7 Tea 0 0 00 10 7 50 TOTAL 10 7 50 204 153 00 HAPPY HOUR hh Accounting Summary Selection hhven hhsal hishhven hishhsls 1 Cola 3 0 50 1 0 45 2 Cola 0 0 50 8 3 60 3 Cola 0 0 50 1 0 50 4 Apple Juice 0 0 50 0 0 00 5 Diet Cola 0 0 50 0 0 00 6 Diet Cola 0 0 50 5 2 50 7 Tea 0 0 50 2 1 20 TOTAL 3 1 00 17 8 50 Vender Cash Accounting BILLS amp COIN IN COIN PAID OUT CASH OUT MANUALLV Recent Hist Recent Hist Recent Hist 7 50 159 75 3 50 19 50 0 00 0 75 COIN TO BOX COIN TO TUBES BILLS IN 4 75 43 50 75 8 25 2 00 108 00 Sold Out Activitv Selection DATE TIME SELECTS ATTEMPTED 1 Cola 9 24 93 1 32pm 13 2 Cola 9 25 93 1 23pm 12 3 Cola 4 Apple Juice 5 Diet Cola 6 Diet Cola 9 26 93 11 30am 5 7 Tea PROGRAMMING THE SIID VENDER To program the SIID Vender it is necessary to enter the System Set Up Audit Diagnostics Mode Open the inner door and press the Service Switch on the control board The display reads ErOr If the display reads 1 00 the door switch did not go to its center position or the switch is defective The door switch has three positions Fully in and fully out puts the vender in its normal m
17. When the temperature of the vapor in the bulb rises it builds up pressure in the bellows tube This pushes the bellows out When the control bulb is cool the vapor shrinks back and the bellows pulls in These movements of the bellows work the switch called the temperature control switch closing it when the bulb is heated and opening it when the bulb is cooled The contacts of the temperature control switch are in the compressor motor s running and starting circuits They are also in the condenser fan motor circuit When the cabinet temperature gets up to the cut in setting the temperature control switch closes in the compressor motor s starting and running circuits and in the condenser fan circuit When the cabinet temperature gets down to the cut out setting the temperature control switch opens in these circuits CAUTION To adjust the temperature control see page 44 THERMAL OVERLOAD ASSEMBLY The thermal overload is a temperature activated switch that interrupts power to the compressor when excessive temperatures occur This switch protects the compressor from the damage that will occur if the compressor continues to operate under adverse conditions The overload also opens under abnormally high amp draws protecting the motor windings from damage Frequent overload trips may lead to warm product and be the first indication of a dirty condenser or other refrigeration related problems that require attention STARTING RELAY The starting
18. change from increment to decrement release the select button and press again PR2P End Time To change end time press and hold select button 3 to change hours and select button 4 to change minutes The time will increment or decrement To change from increment to decrement release the select button and press again There is only one period in a day for enabling secondary pricing NOTE Start time has to be less than end time You must set an on and off time when using PR2P Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu PR2D SET SECONDARY DAYS This function is used to set the days of the week for secondary pricing To view the PR2D press and let go of any select button The display will show ENABLED ON DAYS Day of Week Sunday 1 Wednesday 4 Saturday 7 Monday 2 Thursday 5 Tuesday 3 Friday 6 To change PR2D To Add Days Press service switch ADD will appear on display Press and hold any select button to scroll through days Release select button at desired day to turn on PR2D Press service switch to complete PR2D decision This must be done for each day to be added To Remove Days Press service switch ADD will appear on display Press service switch again DEL will appear on display Press and hold any select button to scroll through days Release select button at desired day to turn off PR2D Press service switch to complete PR2D decision This must be done for each da
19. disables Tube A Select Button 2 When pressed enables and disables Tube B Select Button 3 When pressed enables and disables Tube C Press and hold select buttons 1 amp 2 simultaneously to move to the next item on the menu BILL SET BILLS ONLY SIID Only This function is used to program the vender to take bills only To show the current BILL condition Press select button 1 and the current condition will be displayed To change the BILL condition Press Select Button 1 When pressed enables BILLS YES mode You no longer need to use a changer the controller will operate with bills only Press Select Button 2 When pressed enables BILLS NO mode You need to use a changer the controller will not operate the note acceptor without a changer Press and hold select buttons 1 amp 2 simultaneously to move to the next item on the menu LIM LIMITED ACCESS MENU This function is used to program the vender to use the Limited Access Features To move to Secondary Price Menu SEC press amp hold select buttons 1 amp 2 simultaneously to enter the sub menu press select button 1 The following are sub menus of Limited Access Menu LAOS LAOD PER1 PER2 and RTN LAOS LIMITED ACCESS ON SELECTION This function is used to set selection s which will be limited during certain periods of the day To view the limited access on selection condition press any select button The display will show DISABLED or ENABLED SEL
20. the Hub facing you slowly slide the Cam on the front shaft of the Vend Motor while depressing the Lock Tab See fig 6 NOTE Reference below for timing of the Motors 4 A distinct click will be heard when the tab has locked into the locator hole of the motor shaft CAUTION Depress the Switch Arm when installing the Cam to prevent possible damage to the Switch Arm TO INSTALL AN ADJUSTABLE CAM 1 Select the Adjustable Cam required See page 39 2 Locate the Lift Tab on the outer edge of the Cam See fig 5 3 With the Lift Tab facing you align the slot of the Adjustable Cam with the Locking Tab of the Vending Cam 4 Place the Adjustable Cam on the Vending Cam CAUTION Depress the Switch Arm when installing the Cam to prevent possible damage to the Switch Arm 5 Liftthe Lock Tab of the Vending Cam at the same time lift the Lift Tab of the Adjustable Cam and rotate the Adjustable Cam clockwise to the desired setting TO REMOVE AN ADJUSTABLE CAM 1 Liftthe Lift Tab and rotate the Adjustable Cam clockwise until the Vending Cam Lock Tab is aligned with the slot of the Adjustable Cam 2 Remove the Adjustable Cam from the shaft of the Motor TO REMOVE THE VENDING CAM 1 Depress push in the Lock Tab firmly to disengage it from the Motor shaft 2 Atthe same time pull the Vending Cam towards you until it is removed from the Motor shaft TIMING TO SET THE TIMING OF A NARROW COLUMN VEND MOTOR 1 Make sure the hole throu
21. the User Option Menu Press select buttons 1 amp 2 simultaneously to return to LAOS Press select button 1 to return to the User Option Menu at LIM Press 8 hold select buttons 1 8 2 simultaneously to move to the next item on the menu SECONDARV PRICE MENU This function is used to program a second price for each selection To enter the sub menu press select button 1 The following are sub menus of Secondary Price Menu 5 2 PR2P PR2D and move to User Options Menu press select buttons 1 amp 2 simultaneously until RTN shows on display Press select button 1 to return to USER S P2 SET SECONDARY PRICE This function is used to set a secondary price for each selection When a select button is pressed the price for that selection will be displayed If the button is held in the price will increment or decrement To change from increment to decrement release the select button and press it again Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu PR2P SET SECONDARY PERIOD This function is used to set time to start and end secondary prices To display PR2P start time press and let go of select button 1 or 2 To display PR2P end time press and let go of select button 3 4 To Change PR2P Start Time To change start time press and hold select button 1 to change hours and select button 2 to change minutes The time will increment or decrement To
22. the floor If you cannot level the vender select another location Do not place any objects under the machine DANGER The vender must be properly located and leveled to minimize the risk of injury or death from tipping in the event of user misuse or vandalism SPACE THE VENDER Do not block the rear of the vender Keep the vender 4 inches 10 cm from the wall to insure adequate airflow to the condenser and compressor At the front of the vender make sure that nothing obstructs the air intake at the bottom of the main door At the rear of the vender make sure nothing obstructs the air exhaust at the bottom of the cabinet LOADING THE VENDER All SIID Venders are shipped ready to vend 12 oz cans unless another package was specified at the time the vender was ordered from the factory If a package other than a 12 oz can is to be vended contact a Dixie Narco Factory Service Representative or refer to the proper technical bulletin for spacer settings and shims INITIAL LOADING Oscillators must be in the extreme left or right position to insure proper loading When loading wide columns the first row of cans should be loaded on the bottom bar of the oscillator The second row of cans must be loaded on the top bar of the oscillator Always load complete rows do not load only to the back or only to the front of the column Rotors must be in the cup position to receive the first cans When loading narrow columns lay the rows in the column until the co
23. to be removed NOTE Only one limited access on days change be made at a time The service switch must be pressed before and after each change Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu PERIOD 1 This function is used to set time to start and end limited access To display PER1 start time press and let go of select button 1 or 2 To display PER1 end time press and let go of select button 3 or 4 To Change PERI Start Time To change start time press and hold select button 1 to change hours and select button 2 to change minutes The time will increment or decrement To change from increment to decrement release the select button and press again PER1 End Time To change end time press and hold select button 3 to change hours and select button 4 to change minutes The time will increment or decrement To change from increment to decrement release the select button and press again NOTE Start time has to be less than end time You must set an on and off time when using Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu PER2 PERIOD 2 Set time to start and end limited access the same as period 1 Limited access can be enabled for two different periods in one day Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu RTN RETURN This function is used to return to
24. with these functions DEXUCS communications to a hand held computer is available to provide the ability to measure each vending location for product performance vender performance and accessing accounting data This data can be used to maximize the efficiency of routes for servicing venders DEX communications also provides the bottler security for the integrity of the cash in versus the product sold The vender design provides the flexibility required for the changing beverage industry as well as dependable performance for many years This manual is prepared to assist the proper installation and set up of the vender Please read this manual carefully and become familiar with the SIID Vender before placing the vender on location RECEIVING INSPECTION Upon receipt inspect the vender for any shipping damage If there is any damage have the driver note the damage on the bill of lading and notify Dixie Narco Although 1 regulations require that the consignee originate shipping damage claims Dixie Narco will gladly help if you must file a claim UNPACKING THE VENDERS Remove the stretch wrap and top cover from the vender If flavor labels were shipped with your vender they will be affixed to the back of a vender in the shipment or in the cash box NOTE DO NOT STORE THE VENDER OUTSIDE WITH THE STRETCH WRAP ON THIS COULD CAUSE THE STRETCH WRAP TO BOND TO THE VENDER S SURFACE WHICH COULD DAMAGE THE FINISH Remove the shipping boards from t
25. x1 801 809 80 1 NA 801 809 79x x1 801 809 79x x1 NA 609 070 80x x3 609 070 80x x3 609 070 80x x3 609 070 90x x3 609 070 90x x3 609 070 90x x3 801 806 18x x1 801 806 18x x1 801 806 18x x1 Orange 4 deep 801 810 39x x1 801 810 39x x1 801 810 39x x1 Adjustable Narrow Column b 801 806 61x x1 801 806 61 1 801 806 61 1 Motor Switch Single Price double 804 100 69x x1 804 100 69x x1 804 100 69x x1 SIID single 804 100 73x x1 804 100 73x x1 804 100 73x x1 Vend Motor Switch Insulator All Styles 905 800 33x x1 905 800 33x x1 905 800 33x x1 Vend Rotor Narrow Column All Styles 801 201 56x x1 801 201 56x x1 801 201 56x x1 Vend Oscillator Wide Column All Styles 801 201 57x x1 801 201 57x x1 NA Package Retainer Oscillator All Styles 801 807 87x x1 801 807 87 1 IA EA WAS Front Wide Column Only RE ai s 10A Sold Out Switch Assv GI Single Price 2 4 Price 1731 804 100 68x x1 510 gold cross point Xenoy 1731 5 Paddle Standard Special Use Only Narrow Special Use E Nodess 10C Sold Out Paddle Spring All Styles 901 700 74x x1 901 700 74x x1 901 700 74x x1 11 Mechanism Supports ee All Models Rear 497 070 01x x3 497 070 01x x3 497 070 01x x3 12A Evaporator Fan Motor Assy 330 ml x 4 Can Assy Rotor 801 201 65x x1 801 201 65x x1 801 201 65x x1 491 000 20x x3 491 000 20x x3 491 000 20x x3 491 14
26. 0 40x x3 491 140 40x x3 491 140 40x x3 Eaporator Fan Motor 115V 804 500 59 1 804 500 59 1 804 500 59 1 MARKETING SERVICE MANUAL DIXIE NARCO INC 220 240V 804 500 52x x1 804 500 52x x1 804 500 52x x1 MARKETING SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION DNCB 600E DNCB 501E DNCB 276E 79 Wide 72 Wide 72 Narrow 120 Evaporator Fan Motor Bracket All Styles 164 040 08x x3 164 040 08x x3 164 040 08x x3 Evaporator Fan Blade All Styles AD775CW32S FV775CW30S 801 303 27 1 801 303 27 1 801 303 27 1 Cute Assy 624 070 10x x3 624 070 10x x3 624 070 00x x3 805 701 04x x1 805 701 04x x1 805 701 03x x1 801 903 62x x1 801 903 62x x1 801 903 57x x1 609 070 48x x3 609 070 48x x3 609 070 48x x3 903 300 77x x1 903 300 77x x1 903 300 70x x1 169 000 13x x3 169 000 13x x3 169 000 13x x3 176 072 11x x3 176 072 11x x3 16 Flat Shim 3 16 wide column 801 809 72x x1 801 809 72x x1 Flat Shim 3 32 wide column 801 809 81x x1 801 809 81x x1 NA Bottle Shim Right narrow column Expose Stiffener 801 304 96x x1 801 304 96x x1 801 304 96x x1 Chute Can Bottle Chute Liner Kydex Can Bottle Chute Bracket Foam Block EPS Hinge Pocket Cover o E g 2f 5 3 92 5 n lt D n Can Stop Shim Right narrow column 609 070 14x x3 Bottle Shim Right narrow column 609 070 15x x
27. 1 Syrup on brake 2 Locate check brake spring 3 Check motor switch Check wiring from to motor switch of problem column Check wiring at mate n lock on cabinet harness and cabinet extension harness Check motor Check control board Problem Column will not vend Troubleshooting to diagnostics and test Check for bad connection or broken backed out or crossed wires Also check ballast wires Problem Motor stops on high cam Troubleshooting Change vend switch B Install current software 5 or 380 11 or greater two button programming 3 16 or 390 11 or greater four button programming 5110 VENDING Problem motors work Troubleshooting Check F2 motor power fuse 6 Amp Check lamp and lamp wiring for broken backed out or crossed wires Check ballast and ballast wiring for broken backed out or crossed wires Problem F2 motor power fuse continuously blows Troubleshooting Check if 6 Amp fuse is used Check that capacitor instead of MOV used at CRI location Check ohms of each motor in off state unplug wires to coil of motor ohms should be 6 5 if less coil of motor has a short Check motor harness Check motor extension harness Check for bad bulb in lighting system INI 510 CURRENCY Problem Will not accept coins or bills Troubleshooting Check coin return lever is not pressed Check peripheral 1 0 Amp fuse
28. 1 60x x1 SIID Control Box Warning Label 803 848 28x x1 803 848 28x x1 803 848 28x x1 4 Button Programming 903 054 06x x1 903 054 06x x1 903 054 06x x1 803 856 29x x1 DIXIE NARCO INC COCA COLA MARKETING MACHINE SERVICE MANUAL 2 ju O amp ic wa 8 wn O E Hv 2 le ont 2 E des 8 E MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC SCREWS 8 NUTS e 9003064 Phi Pan Swage Formwiwasher 6 32x T 90030185 Phil Swage Form H10 ars 900201502 Screw Vend Motor 84 24 x 3 4 Single Switch Screw Vend Motor 44 24 x 1 1 16 Double Switch AST 9000 Screw Vend Motor Triple Such e 80030155cxi Screw Phi Pan Cung 8 32x38 7 A10 900 201 31xx1 Screw Machine 6 32 x 1 1 4 Ari 90030197xxi Sorew Pan Sems 8 32x 7 Screw Phil Head Truss 6 x 3 8 Screw Machine Phil Pan 8 32 x 3 4 Screw Tap 1 4 20x1 Type F Screw Truss Type 23 8 32x1 2 Screw Phil Flat 23B 10 32x1 2 900 302 02x x1 Screw Self Tapping 8 18x3 4 A36 900 201 86x x1 Screw Phil Pan Head 6 32x1 4 B 900 800 65x x1 Keps Nut 10 32 Reps Nut 174 20 B6 a a Reps Nut ad 900 902 37x x1 Push Nut Acorn Type B10 900 801 02x x1 Hex Nut 5 16
29. 1 or greater four button programming Problem Software does not work with free vend note token BASO Troubleshooting Install current software 380 51A or greater two button programming 390 31 or greater four button programming Problem 9302GX changer dispenses nickels first then correct change lights come on sample price this occurs 606 Troubleshooting Load the nickels in coin fill CD mode Note This is a Coinco 9302GX problem SIID SOLD OUT MESSAGE Problem Sold out message stays Troubleshooting Check limited access program Check for crossed wires in cabinet harness and cabinet extension harness or loose wire harness connection Check for motors rubbing motor cover on early SIID venders Problem Sold out message comes on with product in column Troubleshooting Check programming and ensure limited access is not on Check for bad connections or broken backed out or crossed wires from select switch to control board Note Check wires on left side of motor cover Check for motor rubbing motor cover on early SIID venders Problem 5 10 switches work the incorrect column Troubleshooting Ensure correct cabinet harness and select harness are being used Check for crossed wires in cabinet harness or cabinet extension harness SIID SELECT PANEL DISPLAY Problem Plug in vender and displays a blank or appears on the display v
30. 18 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC SS SS 03 ze IL E2 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC WASHERS BOLTS 8 MISC HARDWARE Washer Delrin 040 Thick 3 8 IDx5 8 OD Lockwasher Split 3 8 Lockwasher Shakeproof 5 8 1132 00 00 0551 Steel Washer 18 Gauge 1 2 x3 16 Washer Flat 030 thick 188 IDx 5 OD Washer Flat 18 Gauge 17 64 1Dx5 8 OD Washer Flat 14 Gauge 5 16 3 8 7 900 400 43x x1 T Bolt 8 32 x 1 obsolete 900 400 41x x1 T Bolt 8 32 x 1 3 8 900 400 35x x1 T Bolt 8 32 x 3 4 D 900 400 45x x1 T Bolt 8 32 x 1 2 E 900 400 44x x1 Refrigeration Bolt 3 8 16 x 1 Carriage Bolt 1 4 20 x 1 Carriage Bolt 1 4 20 x 1 1 4 Carriage Bolt 1 4 20 x 3 8 Carriage Bolt 1 4 20 x 3 4 Carriage Bolt 1 4 20x5 8 obsolete Carriage Bolt 5 16x18x1 1 4 Top Hinge drop in i Pop Rivet Aluminum 1 4 Pop Rivet Steel Zinc Plated 1 8 Pop Rivet Steel Zinc Plated 3 16 ks Christmas Tree Clip 354280307 00 T
31. 3 Angle Shim wide column Angle Shim narrow column 609 010 10x x3 Rotor Shim 330 ml x 4 609 070 57x x3 Shim 330 x 4 Can Narrow Column 609 070 53x x3 Shim 25 cl x 4 Can Narrow Column 609 070 56x x3 Rod and Spring Assy narrow column 52 ai A All Styles 609 070 30x x3 Tubes for Rod and Springs MAA A White Oscillator Paddle Extension w bottle stop All Styles advised set up 324 010 21x x3 324 010 21x x3 Bottle Divider EA A DAA eee All Styles for advised set up Trim Vend Motor Cover waw All Styles AA A 2 gt MARKETING SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION DNCB 600E 501E DNCB 276E 79 Wide 72 Wide 72 Narrow Screw Phil Pan 8 18x1 2 900 301 84x x1 Screw Hex Washer 1 8 32x3 8 900 303 08x x1 Speed Nut 900 800 85x x1 AA SEA EN DER F5 Pop Five Steel Zinc Plated 18 Pop Rivet Steel Zinc Plated 3 16 901 100 60x x1 00040710001 Clamp Nvlon 3 4 3382BL 901 900 55x x1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC 15 NO A AN N jii ili 5 U U il MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC REFRIGERATION SVSTEM ITEM DESCRIPTION DNCB 600E DNCB 501E DNCB 276E 1207 509040053 1 3 220 240 50 1223 E IEC 609 041 10x x3 609 047 30230 1 3 HP 220 240 50 E 1223 E G
32. 8 Select Select Button Select Button Retainer 063 1 9 1ex14 he Select Button Stop 063x2 301x14 813 Select Switch SIID Switch Insulator Coin Insert Panel Weld Assembly Domestic Export Coin Insert Panel Stud Assembl Domestic Export POS Window Lens 2 3 4 5 7 7 8 8 POS Window Gasket 8 POS Window Backup Plate 045x5 422x13 332 Coin Insert POS Card Thirst Feature Button Retainer Feature Button Stop Feature Button Mars Validator Mounting Plate Filler Plate Feature Button Assy Feature Button Plate Assy Display Lens Display Lens Gasket 1A 1B A B A B 108 10C k Display Visibilitv Validator Filler Plate DIXIE NARCO INC 624 051 80x x3 624 051 90x x3 624 052 00x x3 624 052 10x x3 801 810 62x x1 MESZ 624 050 12x x3 pce ei 805 700 58x x1 2 804 100 74 1 801 805 92 1 624 053 90x x3 624 054 00x x3 IU 624 051 30x x3 624 051 40x x3 Irc 801 810 69x x1 ERA 802 001 29 1 Zo 624 050 48x x3 di 803 853 87 1 A 805 700 93 1 805 700 94 1 624 050 56x x3 624 050 57x x3 624 051 50x x3 624 051 60x x3 801 810 67 1 Bes 802 001 28x x1 802 001 31 1 Roe 360 050 72x x3 MARKETING SERVICE MANUAL DIXIE NARCO INC OI nn A A Coin Insert Label S3D iss 624 050 84 3 pr 803 853 85x x1 _ Screw
33. C COMPONENTS MISC LABELS ITEM DESCRIPTION DNCB 600E 501E DNCB 276E en al 53 2 pet ates ee UE C DP A E 3 SID Contro Board 003 bil Door Swich KEE 804 100 77x x1 804 100 77x x1 804 100 77x x1 Controller Software Eprom 804 911 390 51 804 911 390 51 804 911 390 51 804 911 390 81 804 911 390 81 804 911 390 81 804 909 80x x1 804 909 80x x1 804 909 80xxi 7 NE PARO 6 Amp Slow Blow Fuse 804 800 71x x1 804 800 71x x1 804 800 71x x1 Amp Fast Acting Fuse 804 901 93x x1 804 901 93x x1 804 901 93x x1 Amp Slow Blow Fuse SIID Only 804 800 72x x1 804 800 72x x1 804 800 72x x1 splay Segment Character Dec tutem 2 4 Segment 804 912 79x x1 804 912 79x x1 804 912 79x x1 803 855 73x x1 803 855 73 1 803 855 72 1 803 855 72 1 oz Ps ola B D 3 ANA ale 2 gt CD o amp E G 9 803 854 39 1 803 854 39 1 0 A U 6 gt 0 a E G 0 A U fe 5 0 a E G 2 ed S3D 9 9 with Sold Out Lights 803 856 35x x1 803 856 35x x1 803 856 34x x1 803 856 34x x1 S3D 9 7 without Sold Out Lights 803 856 36x x1 Outi 803 856 37xx1 Press Selection to Display Price or Sold Out 803 902 55x x1 803 902 55x x1 803 902 55x x1 4 Button Programmin
34. EE Screw Phil Pan w out washer 8 18 12 900 301 50x x1 Screw Phil Pan Swage Form 8 32 900 301 80x x1 Screw Phil Pan Swage Form 8 32x s prior to 1970 6462 900 301 56x x1 Screw Phil Pan Sems 8 32x s n 1970 6462 amp higher 900 301 97 1 Screw Machine Truss 10 32 gt 900 201 14x x1 Screw Phil Pan Sems w washer 8 18 900 301 65x x1 A A ee ee Keps Nut 10 32 900 800 65x x1 Keps Nut 14 20 900 800 67x x1 Nut 8 32 900 800 50x x1 7 Elastic Stop Nut 8 32 900 800 51x x1 A ee 20 Nylon Spacer prior to 1970 6462 801 902 48 1 RES ES ___ 900201 7 1 E5 F5 E Carriage Bolt 1 4x20x1 900 201 17x x1 Carriage Bolt 14 20 2 900 201 45x x1 Carriage Bolt 14 20x 900 201 54x x1 Carriage Bolt 14 20 Red 900 202 04x x1 ia TA F5 Pop Rivet Steel Zinc Plated 901 100 61x x1 r IA 801 902 48x x1 5 9 1 2 3 7 12 2 4 5 Screw Machine Phil 8 32x3 4 900 201 22x x1 COCA COLA MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC CI MARKETING SERVICE MANUAL DIXIE NARCO INC PULL OUT HANDLE amp COIN INSERT ITEM DESCRIPTION PART NUMBER 1A Assy T handle w 2 2 22 801518 20 1 1 Flange aa 1C T Handle Onl 801 518 18x x1 801 518 14x x1 T Handl
35. EN 609 041 50x x3 609 041 50x x3 609 041 50x x3 Compressor FFI12HBX 115 60 1 3 HP 802 501 74x x1 802 501 74x x1 802 501 74x x1 FFIT2HBK 220 50 1 3 802 502 17x x1 802 502 17x x1 802 502 17x x1 Compressor Lead Harness Mn 115 60 1203 904 900 61x x1 904 900 61x x1 904 900 61 1 804 904 49 1 804 904 49 1 804 904 49x x1 220 50 904 900 61x x1 904 900 61x x1 904 900 61x x1 2A 2B 2C Compressor Mounting Grommet All Styles 902 000 57x x1 902 000 57x x1 902 000 57x x1 2D Compressor Mounting Clip anni 900 907 BBX 2E Compressor Grommet Plug Plastic BE eae Condenser Base Plate EIERE 38 Condenser Fan MoforAssy B 115 60 491 040 20 3 491 040 20 3 491 040 20 3 220 50 491 140 30x x3 491 140 30x x3 491 140 30x x3 SC Condenser Fan Molor And Bra L T 115 60 804 500 67 1 804 500 67x x1 804 500 67x x1 220 50 804 500 70 1 804 500 70 1 804 500 70 1 SD Condenser Fan Blade AA 4A Drain Pan Assy w Fiberglass Soakers A Dra Pan Paste W Finger Na een _ rr rere G Soakers Heger 14150158 Er um s i a Camp rrr 5 Rear Condensate Plate a H pin Tabs DANA AAA ES Drain Tube E TR Drain Fos 78 Drain Camp eee ee l
36. ID Coca Cola Marketing Machine Parts Service Troubleshooting Manual Beginning Serial Number 0001 65018 June 1998 Y Dixie General Information anno id NE KANE E ENNA 3 through 5 Installation amp SetUp TENG EA KANGENE ta Pages 6 through 10 Hardware Configuration 4 nennen Pages 11 through 13 SID Audit Features iii iii iii rc ee ee WAB BRAH KAG da ta cade cada Pages 14 through 18 Controller 10 Pages 19 through 31 Programming Quick 32 Electrical Parts amp Their Functions u u Pages 33 through 37 Product ieee uu 2 A Page 38 Adjustments Cams Rear ener u nennen 39 through 42 General Maintenance is si uu uu 43 44 Trouble Shooting Flow Charts I u Pages 45 through 57 Trouble Shooting Examples nn nnn nan Pages 58 through 64 Vending uk Pages 58 and 59 Ee TL de EE Pages 60 and 61 Sold Out Message fme DD Page
37. ID The select switches interface directiv to the main controller The motors used on the stack continue to be 115 VAC The vend switches and sold out switches are low voltage There is only one vend switch per motor and one sold out switch per column The motors vend switches and sold out switches directly interface to the main controller board Each motor is independently controlled to provide the maximum flexibility for to sales The Main Controller supports up to 10 motors and 10 selections The Main Controller consists of one board It consists of all the intelligence memory switch interfaces stack interface motors vend switches and sold out switches and peripheral interfaces which include coin changers dollar bill validators DEX interface and debit systems The DEX interface supports both an internal connection as well as an external connection The interconnect is a 1 4 phono jack as specified and approved by NAMA All electrical specifications protocols and baud rates are identified in the specification The door switch is included to determine door accesses A service switch is located on the main controller board to access accounting data programming features and access diagnostic features through the front select panel A real time clock RTC with battery backed memory is provided so memory can be maintained during power failures The life expectancy is 5 years shelf life and 10 years operational The real time
38. ING THE COMPRESSOR ELECTRICAL CIRCUIT IS ALWAYS LIVE WHEN THE PLUG IS CONNECTED TO AN ELECTRICAL OUTLET REFRIGERATION CONDENSER Check the condenser periodically for dirt or lint build up 2 Remove the build up with a brush or vacuum or blow the dirt out of the condenser with compressed air and approved safety nozzle 3 Ensure nothing obstructs air intake at the bottom of the main door 4 Ensure nothing obstructs air exhaust at the rear of the cabinet COIN ACCEPTOR Follow the Coin Acceptor Manufacturer s instructions LUBRICATING THE VENDER The vender refrigeration system does not require any field lubrication The hermetic refrigeration system and fan motors are manufactured with lifetime lubrication Temperature Control Adjustments Adjustment 1 Temperature Adjustment Turn the adjustment clockwise for colder product and counter clockwise for warmer product This will change the cut out temperature only the cut in temperature remains constant Adjustment 2 Altitude Adjustment WARNING DISCONNECT POWER TO THE VENDING MACHINE BEFORE PROCEEDING WITH THIS ADJUSTMENT The control is factory set for an altitude of 152 M 500 ft For higher altitudes adjust the inside range screws to prevent freeze up of the product Adjust the inside range screws as follows 5110 VENDING 1 Problem Free vend on one column Troubleshooting Check selection price Check for bad connections or broken backed out or crosse
39. NY WAY BYPASS THE GROUNDING OF THE VENDER If the outlet will not accept the power cord plug contact an electrician to install a proper AC outlet COIN CHANGERS AND OTHER ACCESSORIES The SIID vender must have a coin changer installed and can have a bill acceptor installed If the coin changer and other accessories are not factory installed refer to the instructions received from the manufacturer of the coin changer and other accessories for proper set up and installation The SIID vender will support the following coin changers Multi Drop Coin Mech Domestic Coinco 9302GX Mars TRC6510 BILL ACCEPTORS If a bill acceptor is not factory installed a bill acceptor interface harness must be ordered from Dixie Narco See the chart below Bill Acceptor Interface Harnesses Also requires parts from acceptor manufacturer Note Bill acceptors will be inhibited anytime the door interlock switch is in the center position Service mode enable even if service mode time out has occurred restoring the vender to normal operation OTHER ACCESSORIES The SIID Vender is capable of interfacing to Debit Card and Data Recording systems At this time only a few such accessories have been tested by Dixie Narco If such accessories are to be used check with either Dixie Narco or the accessory manufacturer about physical and electrical compatibility before attempting to interface such accessories to the SIID Vender INSTALLING A COIN CHANGER Hang the coi
40. Phil Pan 4 24x 900 300 47x x1 DIENEN PANG ee s Keps Nut 14 20 900 800 67x x1 Keps Nut 8 32 900 800 50x x1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC LIGHTING ITEM DESCRIPTION PART NUMBER 1 Fluorescent Bulb ee 1A 1B 1C 48 T8 Metric Philips 36W 840 NG export 0 T8 Metric Philips TLD 58W 840 NG export 72 T8 Metric Philips TLD 70W 840 NG export Door Bracket Lamp Socket ee 110V 045 x 2 684 x 2 985 4 per 220 50 045 x 3 043 x 2 289 3 per 220 50 79 Bulkhead Socket Bracket 045 x 2 061 x 3 491 1 per Lampholder Top WWG 523 4 Lampholder Bottom 99x H O 524 804 902 00x x1 220 50 Light Harness 804 917 14x x1 Ballast High Output 110V 60Hz domestic 804 400 38 1 High Output 220 240V 50 60 Hz export Jumper Lamp Fixture 22 Bottom 110 60 2 domestic 22 220 50 Lamp 24 Boot Lamp IA Lamp Socket Shield ER ee 624 050 83x x3 220 V International Ballast Jumper 1 Light Harness Plug In 1 H O 804 916 02 1 2 3 8 220 50 4 per Leviton 13351 UN 804 91 7 16x x1 5 7 1 804 917 15x x1 Screw Phil Swage Form 6 32 900 301 70x x1 MARKETING MACHINE SERVICE MANUAL WIRING HARNESS Cabinet Harness SIID 9 Cam and Sold
41. RN Portuguese PORT Slovenia SLOV Press and hold select buttons 1 amp 2 simultaneously to move to the next item on the menu PROM PROMOTIONAL SALES This function is used to initiate a promotional sale To show the current promotional condition Press Select Button 1 To show UN where equals the number of vends required to initiate promotion Press Select Button 2 To show FR where equals the number of free beverages to be delivered after the number of required vends have occurred as programmed to initiate promotion Press Select Button 3 To show enabled s of the selections that are enabled for the promotion To change the promotional sales conditions Press amp hold Select Button 1 The number of vends required to initiate the promotional sale will increment from zero to 25 and then return to zero Release the select button when the desired number of vends to initiate the promotional sale is displayed Note If UN 0 the promotion is disabled Press 8 hold Select Button 2 The number of free beverages to be delivered after the number of vends have occurred will increment from zero to 25 and then return to zero Release the select button when the desired number of free beverages to be delivered is displaved Note If FR O the promotion is disabled Press amp hold Select Button 3 Display will show ENABLED SEL s where shows the selections that are enabled for the promotion to occur add o
42. Sold Out Switches F Coin Mech The operator will manipulate switches run motors and insert money while the SIID control box monitors all these functions If any errors are found they will be logged and displayed to the operator on the display SIID Quick Reference Menu Prompts M inMenu SubMenu 02 HD Historical Data RD Resettable Data S P Set Price C D Coin Dump Coin Fill USER User Options STS Space To Sales TIME Time DATE ESC Escrow LANG Language PROM Promotional Sales ECNT Electronic Counters NF Note Factor CR Change Rules BILL Bill Only LIM Limited Access LAOS Limited Access on Selection LAOD Limited Access on Days PER1 Period 1 Start End PER2 Period 2 Start End RTN Return SEC Secondary Prices S P2 Set Secondary Prices PR2P Set Secondary Period PR2D Set Secondary Days RTN Return ACD Set ACD Audit Box FREE Free Vend Enable 5 6 7 amp 8 selects DST Daylight Savings Time DSTR Daylight Savings Time Rules SCE Small Coin Enable COIN Coin Rules SSM Scrolling Message Mode MV Multi Vend RTN Return DIAG Diagnostics SE Select Switch Test SP Sold Out Paddle Test SW Sold Out Switch Test MT Motor Test CM Coin Mech Test Note Acceptor DSP Displav Test VERS Software Version VNDR Vender Identification RTN Return AUTO Auto Testing A Press 8 hold buttons 1 2 simultaneousiv to move
43. ash Box W A pe 3 Cash Box Coin Chute Assy Cash Box Shelf Wide Closure Strip Wide Narrow Cover Wire Plug Wide Narrow 13 L Profile Gasket Wide Narrow Assy Coin Return Cup Wide Narrow Weld Assy Coin Return Cup Wide Coin Return Cup Door 18 Lamp Bracket Wide Narrow 530 Mounting Bracket 72 Wide Narrow 79 Wide Bracket Door Switch 3 801 810 68x x1 Berl 624 052 40x x3 624 050 64x x3 624 050 63x x3 BEE 624 050 03x x3 Wix 805 700 89x x1 BES 805 701 12x x1 805 700 69x x1 0 H 55 801 401 83 1 801 401 84 1 WEE EE KE Fd Na 624 050 39x x3 801 305 14x x1 624 050 72x x3 624 050 73x x3 Wide Narrow 604 051 28x x3 19 Bill Validator Guard Wide Narrow 805 700 98x x1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION PART NUMBER Access Door Anti Vandal Bracket 805 701 02x x1 Access Door Jamb ee en al Wide Narrow prior to 6506AX 805 700 97x x1 Wide Narrow 0001 6506AX and higher 805 701 09x x1 Coin Chute Bracket 805 701 01x x1 Standoff TV 901 001 46x x1 Push Nut Acorn Type IIA xa 900 902 37 1 20 21 22 23 25 Sirap sao T 222 22 624 050 79 1 26 Access Door Hinge 0001 6506 and higher re ee 624 054 10 3 Bottom 624 054 20x x3 27 Access Door Latch Ta 0001 6506 and higher 801 304 53 1 F a
44. bleshooting Check door switch Check validator Check interface harness Problem Want to install debit card system Troubleshooting Need to contact card system supplier for details Problem 1 and 5 Bill Acceptance Black label box 2 button programming Troubleshooting A Works with 1 BA 30 2 VFM 3 Low Level 3 DBA 2 or 3 Problem 1 and 5 Bill Acceptance Red label box 4 button programming Troubleshooting Works with 1 BA 30 Mdb 2 Mars VN 2500 Series Mdb 510 CURRENCY Problem Install bill unplug vender plug vender gives 1 credit and bill back Troubleshooting Set Escrow to Pr or 5 4 B Install current software 5 or 380 11 or greater two button programming 3 16 or 390 11 or greater four button programming Problem Install Debitek card unplug vender plug in vender jackpots changer Troubleshooting A Install current software Eprom 5 or 380 11 or greater two button programming 3 16 or 390 11 or greater four button programming Problem After a few vends the Mars 6510 disables itself i e stops taking coins Troubleshooting A Install current software Eprom 804 911 380 41 or greater two button programming 804 911 390 21 or greater four button programming Problem New 4 tube changer will not pay out dollar coin Troubleshooting A Install current software Eprom 380 51 or greater two button programming 390 1
45. ce have to be the same price and all prices on secondary price have to be the same price 14 Problem When programming the display takes 30 to 45 seconds to from one program to another Troubleshooting Unplug the coin mech and then program the SIID control box 15 Problem Display goes blank when you press a given select button Troubleshooting Check for bad vend motor on selection pressed Wire broken at coil or possible spade pulled out 16 Problem Set price unplug vender plug in vender and price changes to 99 95 Troubleshooting Check battery Follow steps to check 1 Unplug vender 2 Ardac boards locate component LH5168D 10L at U6 on board On DeAmertek boards locate component LH5168D 10L at U2 on board Set volt meter to test DC voltage Put one test lead on pin 14 Put other test lead on pin 28 Volt meter should read minimum 2 VDC If bad battery under 2 VDC replace the board 17 Problem All segments stay illuminated on display Troubleshooting Toggle to proper setting 14 segment versus 7 segment Connector harness loose at display board Check for bad connection or broken backed out or crossed wires is display harness 18 Problem Plug in vender and 1 1 1 1 scrolls across the display Press the service switch and is displayed Troubleshooting Check control board REFRIGERATION PARTS AND FUNCTIONS MECHANICAL PARTS COMPRESSOR MOTOR Th
46. clock is displayed in military time 24 hour clock The RTC is used for time stamping door closures power outages limited access and selective dscount pricing The intelligence of the Main Controller is an Intel 80C32 microprocessor A minimum of 128k of EPROM and 8k of RAM battery backed is provided Early Display Boards will consist of four 7 segment LEDs to provide alpha numeric characters Future Display Boards will consist of four fourteen segment LEDs to provide clearer alph numeric characters Also the exact change indicator consists of an LED FEATURES The following is a description of all the features of the SIID DEX Compatible Hand held Interface The vending industry NAMA has established an audit data protocol which is defined by DEX Direct Exchange Of Data and UCS Uniform Communications Standards This interface is a direct connect as defined by the specification The SIID has provisions for an internal and external connection The external connection provides a limited amount of information The internal connection provides the full capability of DEX UCS These capabilities include full audit of interval and historical data system programming diagnostics and limited access 10 Column Stack Compatible The SIID Controller is capable of driving up to 10 stack motors independently The motors will be 110 VAC The vend Switches and sold out switches are low voltage gold cross point switches The interface for
47. ct button whichever select button you are holding is the select button the additional column will be assigned While holding the select button the display will read ADD and the selection will increment from 1 to 10 Release select button when the desired column to be added is displayed A message will scroll across the display telling you what column will be assigned to the button you were holding Press service switch to complete space to sales decision and re enter service mode To Remove Selection Press Service Switch ADD will be displayed press service switch again and DEL will be displayed Note Pressing the service switch will toggle between add and delete A 10 second inactivity time out will return to STS Press and hold any select button the select button you are holding is the select button from which the additional column will be removed While holding select button the display will read DEL and the selections will increment from 1 to 10 Release select button when the desired column to be removed is displayed A message will scroll across the display telling you what column will be deleted from the button you were holding Press Service Switch to complete space to sales decision and re enter service mode NOTE Only one space to sales change may be made at a time The service switch must be pressed before and after each change Press amp hold select buttons 1 8 2 simultaneously to move to the next item on the men
48. d wires from vend motor to control board Check for sticking select button D Check control board 2 Problem One motor continues to home with door closed shows COLJ when routine is entered Troubleshooting If using Mars Validator ensure correct interface harness is used Check for bad connections or broken backed out or crossed wires from vend motor to control board Note Check wires on left side of vend motor cover Check vend switch Check control board Problem One column sold out but still vends Troubleshooting Check sold out switch Check for bad connections or broken backed out or crossed wires from sold out switch to control board Note Check wires on left side of vend motor cover Problem Vender will not sequence Coca Cola only Troubleshooting Ensure wire 24 is in select panel harness and is in correct pin location Check for bad connection or broken wire 24 in select panel harness Make sure wire 24 is in correct location D Check control board Problem Free vend on one or more columns Troubleshooting Check secondary pricing program Check for bad connections or broken backed out or crossed wires from vend motor to control board Check for sticking select button 0 Check for bad vend motor switch Check control board Problem Column Jackpots Troubleshooting Check problem column s in motor test Check motor for
49. e Stud 801 518 17x x1 Coin Chute Assy 624 052 60x x3 Coin Return Assy 624 052 50x x3 3B Push Button Coin Return 801 807 25x x1 Coin Return Button Bracket 624 050 23x x3 D Bushing 500x 625 801 903 13x x1 E Coin Return Rocker 6 serial break not available at print 805 700 61 1 8 first 10 000 venders s n 0001 6501 to 805 700 56x x1 F Roller Pin 900 502 19x x1 G Roller Pin Retainer 900 900 90x x1 H Coin Return Cable Assy 6 Cable serial break not available at print 801 305 15x x1 8 Cable first 10 000 venders s n 0001 6501 BW to 801 305 17 1 624 050 21 3 Coin Return Changer Rocker PSN Coin Return Spring 624 050 45x x3 K 901 701 07x x1 L Wing Nut 6 32 serial break not available at print 800 801 14x x1 8 32 first 10 000 venders s n 0001 6501BW to 800 801 15x x1 Coin Chute Bracket 805 701 01x x1 A Display Lens Mar B Display Lens Gasket DAA Coin Insert Label E 53 803 853 85 1 EE Coin Return Changer Bracket SIID 803 853 83x x1 Coin Chute Can Diverter EU EAR 3 3 3 3 3 3 3J 3 3 5 5 7 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC p 10B COIN INSERT PANEL SELECT PANEL MARKETING SERVICE MANUAL SELECT PANEL COIN INSERT PANEL ee Select Panel 12 Select 8 Select Select Panel Stud Assv 12 Select
50. e compressor motor sealed in the compressor housing drives the compressor with a shaft that is shared by both parts It is started by the temperature control switch and the starting relay It is stopped by the temperature control switch and if it gets overloaded by the thermal overload switch COMPRESSOR The compressor sealed in the compressor housing draws cold low pressure refrigerant gas from the evaporator and pumps hot high pressure refrigerant gas out to the condenser CONDENSER The condenser located in the base of the vender at the front takes heat out of the hot high pressure gas that comes from the compressor The gas loses heat as it goes through the condenser coils and changes into a liquid because it is still under pressure CONDENSER FAN The condenser fan between the condenser and the compressor motor first draws air from the outside of the vender through the condenser This air takes heat from the condenser first and then is blown over the housing from which it also takes heat before going back outside of the vender The condenser fan runs when the compressor motor runs FILTER DRYER The filter dryer is in the liquid line between the condenser and the capillary tube This dryer filters out any foreign particulate matter and also contains a desiccant to absorb any moisture that may be present in the system CAPILLARY TUBE The capillary tube between the condenser and the evaporator in the refrig
51. ect buttons 1 amp 2 simultaneously to return to STS Press select button 1 to return to USER Press and hold select buttons 1 amp 2 simultaneously to move to the next item on the menu DIAG DIAGNOSTICS MENU This function allows you to systematically diagnose problems related to the vender To move to AUTO press select buttons 1 amp 2 simultaneously to enter sub menu press select button 1 The following are sub menus of Diagnostics Menu SE SP SW MT DSP VERS RTN Select Switch Press any select button and the display will indicate the number of the select button pressed Press 8 hold select buttons 1 amp 2 simultaneously to move to the next item on the menu SP Sold Out Paddle Test Use this to test the sold out switches if the vender is emptv The displav will reflect anv Sold Out Paddles that are pressed indicating that a column is full The displav will automaticallv scroll through the columns in which the sold out paddles are pressed Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu SW Sold Out Switch Test Use this to test the sold out switches if the vender is full The display will reflect any Sold Out Switches that are pressed indicating that the column is empty The display will scroll through the columns that are sold out Press amp hold select buttons 1 amp 2 simultaneously to mo
52. ender will not funciton Troubleshooting Press a select button to change message on display this should clear RRRR s Remove power to vender for one minute then power vender back up Check main power plug for loose connection Check for bad connections or broken wires from display to control board Check display board TO F Check control board Problem Display will not function Troubleshooting Check for bad connections or broken wires from display to control board Check F1 motor power fuse 1 6 Amp Check display board Check transformer Check control board mog Problem Display shows 1 and then increases in dollar increments Troubleshooting Check coin mech Check validator Check control board Problem Cannot set price on a given selection Troubleshooting Check configuration 1 is set to C1 1 multi pricing Check for bad connections or broken wires from select switch to control board Check select switches D Check control board Problem Vender changes a set vend price to 106 on selections on its own domestic only 10 could be any given price Troubleshooting Check secondary pricing program Check for bad connections or broken wires from select switch to control board Check control board Possible cold solder joints Problem Control board looses its memory when power is shut off to vender Troubleshooting Check battery see problem 16 on next
53. er Rear Stack 801 803 170 01 Oscillator Assembly Nyliner Front Stack 491 070 900 03 114 901 804 230 01 497 071 000 03 T Models Sold Spring 901 700 740 01 Sold Out Switch Assv Snap In 804 100 750 01 Insulator and Switch are one piece Sold Out Paddle Wide and Narrow 432 070 190 13 MOTOR NARROW COLUMN Mounted on the Vender with the Vend Motor Switch the underside See Fig 1 The shaft of the Vend Motor slides into a slot in the Vend Rotor See Fig 2 Vend Motor Switch 804 100 730 01 Rotor 801 201 211 61 114 801 201 220 01 Models Wide 801 201 230 01 Models Narrow PRODUCT SHIMMING Refer to the appropriate technical bulletin for proper set up and vending procedures Listed are a few of the more widelv used Technical Bulletins relating to shimming Fig 2 TB 450 Miscellaneous Worldwide Can Shimming Shimless Stack Series 90 TB 451 Miscellaneous Worldwide Plastic Bottle Shimming T Models 452 Miscellaneous Worldwide Non Returnable Bottle Shimming T Models 453 Miscellaneous Worldwide Plastic Bottle Shimming Shimless Stack Series 90 TB 454 Miscellaneous Worldwide Non Returnable Bottle Shimming Shimless Stack Series 90 TB 455 Miscellaneous Worldwide Can Shimming T Models TB 456 Miscellaneous Worldwide Returnable Bottle Shimming Shimless Stack Series 90 TB 457 Miscellaneous Worldwide Returnable Bottle Shimming Wide Stack Series 90 TB 473 Mi
54. erant line has a very small inside diameter and serves to control the refrigerant flow from the condenser into the evaporator EVAPORATOR The evaporator in the vender cabinet takes heat from the air in the vender cabinet and gives this heat to the liquid refrigerant The liquid refrigerant is evaporated boiled off as a gas and the gas is drawn out by the compressor EVAPORATOR FAN The evaporator fan draws warm air from around the cans or bottles in the cooling compartment and blows it across the evaporator As the air goes across the evaporator it gives up heat to the evaporator then goes back to the cans or bottles and takes heat from them This fan runs continuously when the vender is plugged in CONDENSATE PAN The condensate pan located in the compressor compartment collects the water which runs from the evaporator The water is evaporated into the surrounding air by means of soakers The soakers extend down into the pan to absorb the water Exposure to the surrounding air evaporates the water in the soakers ELECTRICAL PARTS TEMPERATURE CONTROL The temperature control is the part that is made up of a control bulb connected by a small metal tube to a bellows The control bulb is in a slot in the evaporator fan housing The bellows and a switch known as the temperature control switch are in the temperature control box which is fastened to the right side inside the vender The control bulb and the bellows have a vapor in them
55. ess amp hold Select Button 2 Dump Dimes Press amp hold Select Button 3 Dump Quarters Press amp hold Select Button 4 Dump 4 tube in 4 tube changers FILL This section is used to count coins loaded in the top separator of the coin mech Insert coins in the top Separator of the coin mech The total value of the coins will be displayed and will be counted in the DEX audit data so the SIID controller knows exactly how much change is in the coin mech Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu USER USER OPTIONS MENU This function is used to configure the vender to operate in the fashion best suited for the vender location To move to diagnostics DIAG press amp hold select buttons 1 amp 2 simultaneously to enter the USER sub menus press select button 1 The following are sub menus of the User Option Menu STS TIME DATE ESC LANG PROM ECNT NF BILL LIM SEC ACD FREE DST DSTR SCE COIN SSM MV and STS SPACE TO SALES To view the space to sales condition press any select button to display the current columns assigned to that select button To change space to sales condition To Add Selection Press Service Switch ADD will be displayed Note Pressing the service switch will toggle between add and delete A 10 second inactivity time out will return to STS Press and hold any sele
56. g Space to Sales Options 803 849 04x x1 803 849 04x x1 803 849 04 1 i 903 828 82 1 903 828 82 1 903 828 82 1 7 Wei o 5 0 2 E 5 5 34A Removable Substance Validator Opening Instructions Domestic gg 3 5 lt 510 als a 5 6 8 lt zo 213 4 3 EI 6 a 5 5 2 2 10 Lebels IA ed Press Selection to Display Price 903 835 15x x1 903 835 15x x1 903 835 15x x1 MARKETING SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION DNCB 600E DNCB 501E DNCB 276E 79 Wide 72 Wide 72 Narrow Coke Product Label 803 843 43x x1 803 843 43x x1 803 843 43x x1 Price Label 803 843 44x x1 803 843 44x x1 803 843 44x x1 Non 51 Price Label VRV 803 836 16x x1 803 836 16x x1 803 836 16 903 901 29 1 903 901 29 1 903 901 29 1 5 5 5 Coke EVS Revision 2 2 Landscape Programming 803 854 75 1 803 854 75 1 803 854 75 1 Coke EVS Revision 2 2 13 9 Marketing Machine 803 854 76x x1 803 854 76x x1 NA Coke EVS Revision 2 2 9 9 Marketing Machine 803 854 77 1 803 854 77 1 Programming EVS Revision 2 2 Select Button Layout Label 9 Select Coke EVS Revision 2 2 Select Button Layout Label 13 Select Ww ler Dad 12 Installation Set Up Guide 903 901 60x x1 903 901 60x x1 903 90
57. gh the rear shaft is in a horizontal plane If a pin were inserted in the hole the pin would be horizontal See Fig 8 2 The Vend Rotor must be in loading position when the Motor shaft is inserted in the end of the Rotor See Fig 8 3 Insert the Motor shaft in the Rotor and secure the Motor 4 Install the Vending Cam on the front shaft of the Motor making sure the Lock Tab is at the 9 o clock position See Fig 7 5 Install the Adjustable Cam per the instructions given on the previous page TO SET THE TIMING OF A WIDE COLUMN VEND MOTOR 1 sure the hole through the rear shaft is in a horizontal plane If a pin were inserted in the hole the pin would be horizontal See Fig 10 Slide the Drive Arm with linkage attached on the rear shaft as shown See Fig 10 Secure by installing the Groove Pin With the Oscillator in position align the hole in the Linkage Arm with the pin of the Oscillator Slide the Linkage on the pin Install the Vending Cam on the front shaft of the Motor making sure that the Lock Tab is at 6 o clock as shown See Fig 11 NOTE When the screw holding the Linkage Arm to the Drive Arm is at the 12 o clock position See Fig 10 the Lock Tab will be at the 6 o clock position See Fig 11 7 Install the Adjustable Cam per the instructions on page 40 REAR SPACER The Rear Spacer one for each column is located at the rear of the column The latch fingers or spring
58. h the menu While scrolling down through menu release press select buttons 1 8 2 simultaneousiv to scroll up through menu ENTER SUB MENU Press and hold select button 1 to enter a sub menu EXIT SUB MENU With RIN on displav press and hold select button 1 to exit a sub menu EXIT SVSTEM SET UP AUDIT DIAGNOSTICS MODE Closing the inner door or a two minute inactivity time out will exit the system set up audit diagnostics mode FRONT PANEL PROGRAMMING SYSTEM SET UP AUDIT DIAGNOSTICS MENU HD HISTORICAL DATA This section shows the user the vender accounting over the life of the vender Use the following select buttons to view the total sales in dollars total number of vends and the total number of vends for each selection Press Select Button 1 Shows the historical total cash sales for the life of the vender Press Select Button 2 Shows the historical total number of vends Press Select Button 3 Shows the historical number of vends by selection Each selection automatically scrolls across the display Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu RESETTABLE DATA This section shows the user the vender accounting data since the time of the last counter reset This data can be reset either from this menu or by a DEX interrogation Press Select Button 1 Shows the total cash collected since the last counter reset Press Select Button 2 Shows the total number of vends s
59. he bottom of the vender The shipping boards are attached by the leveling legs Remove the shipping boards by unscrewing the leveling legs A 112 inch socket type wrench should be used on the bottom of the leveling legs Be sure to replace the legs after removing the shipping boards To open the vender locate the door lock keys which are secured inside the coin return cup After unlocking the door rotate the T handle counter clockwise until the door can be opened Once inside check the coin box on the door for any additional parts pricing labels or information concerning factory equipped accessories Check the T handle for proper alignment and locking functions Check the lamps for proper installation ELECTRIC POWER NEEDED Refer to the cabinet serial number plate to determine the proper voltage and frequency the machine requires domestically this requirement is 115 Volts 60 Hertz Domestic venders will operate properly 10 of the specified voltage For domestic models this is between 103 volts and 127 volts The cabinet serial plate also indicates the amperage of the vender Single phase alternating current is required The vender must be plugged in its own properly rated circuit with its own circuit protection fuse circuit breaker DO NOT USE AN EXTENSION CORD GROUND THE VENDER The vender is equipped with a three wire power supply cord and MUST be plugged in a properly grounded outlet DO NOT REMOVE THE GROUND PIN OR IN A
60. hs Only This function is used in situations where an Mdb coin mech will recognize a coin which has a lesser value than tube coins and send it to the cash box This coin is not in the coin tubes and the customer wants to use these coins Important Under certain conditions if one of these coins is accepted and escrow return is done the controller may be able to pav back the credit as displaved and that coin will be lost To show current SCE condition Press anv select button and the displav will show the current setting To change the 5 condition Press and hold Select Button 1 to turn 5 on Display will show Press and hold Select Button 2 to turn SCE off Display will show OFF Press and hold Select Buttons 1 and 2 simultaneously to move to the next item on the menu COIN COIN RULES This function is used to allow the exact change light to turn on when appropriate as related to coin tube status or to set the exact change light to never turn on which will allow bills and coins to be accepted regardless of the tube level status of the coin mech To show current COIN condition Press any select button and the display will show the current setting To change the COIN condition Press and hold Select Button 1 to turn COIN on Display will show ON Press and hold Select Button 2 to turn COIN off Display will show OFF Press and hold Select Buttons 1 and 2 simultaneously to move to the next ite
61. in Changer Interfaces The SIID Controller supports the following coin changer interfaces A MDB Multi Drop Specification USA MDB Bill Validators Coinco BA 30 Bill Validators interface to the SIID Controller Also validators which interface to the new MDB Multi Drop Bus specification should also be compatible but have not been tested and approved as of this publication If a bill acceptor is not factory installed an interface harness will need to be ordered from Dixie Narco and or the bill acceptor manufacturer Verifone Debitek Card Compatible The SIID is capable of interfacing to Debit Card and Data recording systems At this time only a few such accessories have been tested by Dixie Narco If such accessories are to be used check with either Dixie Narco or the accessory manufacturer about physical and electrical compatibility before attempting to interface such accessories to the SIID vender The SIID supports any Debit Card Data Recording manufacturer s systems that meet NAMA II protocol SIID AUDIT FEATURES The SIID provides two methods of accessing audit data A limited amount of audit information is available in the system set up audit menu More extensive audit information is accessible electronically SYSTEM SET UP AUDIT MENU Four types of audit data are available in the system set up audit menu CASH which is the historical total cash counted for the vender CLN which is the resettable cash counted for each selec
62. ince the last counter reset Press Select Button 3 Shows the total number of vends by selection since the last counter reset Each selection automatically scrolls across the display Press Select Button 4 This button zeros the resettable data described above Hold button 4 for 5 seconds and COUNTERS RESET will be displayed At this time all resettable data will return to 0 Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu S P SET PRICE This function is used to set the price of each selection When a select button is pressed the price for that selection will be displayed If the button is held in the price will increment or decrement To change from increment to decrement release the select button and press it again To set all selections for the same price set desired vend price on select button 1 then simultaneously press and hold select buttons 3 amp 4 for five seconds this will change the vend price of all selections both primary and secondary to the price programmed to select button 1 Note The SIID s multi pricing capability allows you to set all selections to any price in the range of 0 00 to 99 95 Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu C D COIN DUMP COIN FILL MODE COIN DUMP This section is used to dump coins from the coin mechanism while in C D mode Press amp hold Select Button 1 Dump Nickels Pr
63. innerman Clip Fan Shroud C5207 014 3B Hole Plug Snap in 1 1 4 ASES 804 601 45x x1 ___ 6 Terminal Ring Crimp 16 14 AWG 801 902 48 1 Nvlon Spacer used on D O Boards LN 801 809 12x x1 Velcro Blocks LEER 801 807 49x x1 Vender Defender Clamp 901 901 89x x1 Clamp Cable 1 Heyco 3390 900 901 79 1 Clamp Nvlon 5 16 Black 3355 Dennison 10159 MARKETING SERVICE MANUAL DIXIE NARCO INC 900 901 80x x1 Clamp Nylon 1 2 Heyco 3328 Clamp Nvlon 3 4 3382BL 1 1 0 1 12 901 902 83x x1 Cable Tie 5 5 3 900 902 14x x1 Canoe Clip 254 090 301 00 0108 1
64. l in its entiretv This service information is intended to be used a qualified service technician who is familiar with proper and safe procedures to be followed when repairing replacing or adjusting anv Dixie Narco vender components repairs should be performed a qualified service technician who is equipped with the proper tools and replacement components using genuine Dixie Narco factory parts Repairs and or servicing attempted by uninformed persons can result in hazards developing due to improper assembly or adjustments while performing such repairs Persons not having the proper background may subject themselves to the risk of injury or electrical shock which can be serious or even fatal MODELS AND DETAILS 1439 56 11 16 711mm 28 5 16 737mm 30 1 2 211 464 Ibs 1439 56 11 16 711mm 28 5 16 737mm 30 1 2 211 464 Ibs 1829mm 72 711mm 28 5 16 737mm 30 1 2 260 574 lbs 1829mm 72 711mm 28 5 16 737mm 30 1 2 260 574 lbs 348 Height 1829mm 72 Widih 940mm 37 1 16 Depth 737mm 30 1 2 Shipping Wt 330 728 lbs DNCB 360 Height 1829 72 Width 940mm 37 1 16 Depth 737mm 30 1 2 Shipping Wt 288 634 Ibs DNCB 368 Height 1829mm 72 Width 940mm 37 1 16 Depth 737mm 30 1 2 Shipping Wt 312 688 Ibs DNCB 414 Height 2007mm 79 1 2 Width 940mm 37 1 16 Depth 737mm 30 1 2 Shipping Wt 358 790 lbs DNCB 440
65. lumn is full Do not fill the columns to the top of the cabinet Allow about 3 inches at the top of the column because the can stack will move up and down in the column during the vend cycle Correct loading will prevent service calls and insure proper vending After loading a vender for the first time test vend each selection with money until the first can is delivered This will ensure that the vender is loaded and working properly NOTE TO INSURE PROPER AIR FLOW THROUGH THE EVAPORATOR DO NOT PLACE CANS OR OTHER FOREIGN OBJECTS IN THE BOTTOM OF THE TANK INSTALLING FLAVOR CARDS The flavor cards may be inserted one of two ways 1 in the select buttons or 2 in the flavor card carrier 1 IN THE SELECT BUTTONS Swing the coin changer mounting plate away from the outer door exposing the back of the select buttons The flavor cards are inserted in the back of the select buttons from either side 2 IN THE FLAVOR CARD CARRIER Swing the coin changer mounting plate away from the outer door exposing the back of the select panel Remove the flavor card carrier Ensure the flavor cards are placed in the select button flavor card carrier position that corresponds to the column in which the product is loaded SIID HARDWARE CONFIGURATION The hardware configuration for the SIID Controller consists of a main control board and a displav board The select panel consists of low voltage switches Sold out indicators are eliminated in the SI
66. m on the menu SSM SCROLLING MESSAGE MODE This function is used to turn on a scrolling message ICE COLD DRINKS To show current SSM condition Press any select button and the display will show the current setting To change the SSM condition Press and hold Select Button 1 to turn SSM on Display will show Press and hold Select Button 2 to turn SSM off Display will show OFF Press and hold Select Buttons 1 and 2 simultaneously to move to the next item on the menu MV MULTI VEND This function when turned on allows credit to be retained after a vend so the customer can vend from another selection i e 50 vend price put in 1 00 push a select button and vends 50 still shows on display push a second selection button and vends Credit is cancelled after 5 minutes of inactivity Note If MV is turned on COIN will automatically turn coin rules off There is unlimited acceptance If a customer wants their credit money back the escrow lever must be pressed To show current MV condition press any select buttons and the display will show the current setting To change the MV condition Press and hold Select Button 1 to turn MV on Display will show ON Press and hold Select Button 2 to turn MV off Display will show OFF Press and hold Select Buttons 1 and 2 simultaneously to move to the next item on the menu RTN RETURN This function is used to return to the User Options Menu Press sel
67. n programmed in the service menu can be programmed electronically via the DEX port The following types of data can be configured electronically Machine Identity Date and Time Price and Product Information Space to Sales Limited Access Control Parameters Time of Day Discounts Control Parameters Escrow Mode Escrow mode cannot be transferred with the Norand Device SAMPLE SIID CONFIGURATION amp ACCOUNTING REPORT Vender Identification Serial Number 1234 6132BR Model Number DNCB501T SIID Location NAMA SHOW CHICAGO IL Asset Number 362436 of Columns 8 of Selections 7 Significant Events RECENT HISTORICAL Door Openings 2 12 Power Outages 1 2 Total Vends 10 213 Total Sales 7 50 159 75 Vender Configuration Coin Mechanism MICRO MECH Escrow Mode ESCROW TO SELECT dollar bill escrow SELECTION PRICE HHPRICE DESCRIPTION 1 0 75 0 50 Cola 2 0 75 0 50 Cola 3 0 75 0 50 Cola 4 0 75 0 50 Apple Juice 5 0 75 0 50 Diet Cola 6 0 75 0 50 Diet Cola 7 0 75 0 60 Space to Sales Configuration Selections Columns 1 2 3 4 5 6 7 1 Cola X X 2 Cola 3 4 5 Diet Cola K 6 Diet Cola K 7 Limited Access Days 5 M W Th F 5 K K K K K Times 11 00 10 12 00 and 13 00 10 14 00 Selections 1 Cola 2 Cola 3 Cola 5 Diet Cola 6 Diet Cola Happy Hour Times Days 5 M T W TH F S X Time 08 30 to 17 30 Vender Accounting Summary
68. n changer on its mounting plate and secure it by tightening the three securing screws Plug the coin changer into the 6 pin socket for MDB changers in the vender CAUTION The coin changer must be plugged in with the power removed from the door or the coin changer may not power on properly After restoring power manually load the coin changer coin tubes with at least 10 coins each Following the program instructions for the SIID Vender program each selection for its own vend price A price of 0 00 is free vend After the pricing is return the vender to its operate mode either by closing the door or pulling the door closed switch out Prime the coin changer by making a correct change transaction PLACING THE VENDER ON LOCATION CAUTION DO NOT TRANSPORT THE VENDER TO OR FROM THE LOCATION LOADED WITH PRODUCT OR DAMAGE TO THE VENDER RESULT The vender must be located on a solid flat and level surface The vender must positioned close enough to electrical outlet that an extension cord is not required If securing the vender to the floor or wall is required call the Dixie Narco Factory Service Department or your Dixie Narco Representative for suggestions LEVEL THE VENDER Level the vender When the vender is level the door can be opened to any position and it will not move by itself Open the door to several different positions before deciding the vender is level Make sure that all of the leveling legs are touching
69. ode When the switch is in its center position the System Set Up Audit Diagnostics Mode may be entered There is a time for the service Mode If no accounting or set up functions are used for 2 minutes the vender will return to its normal mode After time out the service switch on the control board has to be pressed to re enter the System Set Up Audit Mode SIID CONTROLLER PROGRAMMING 0773 6201CS amp HIGHER The controller has two modes of operation NORMAL MODE In normal mode the display will show a decimal point If decimal is blinking this indicates an error or problem recognized in the vender When money is inserted the display indicates the total amount of the deposit The select buttons are used to select the product SYSTEM SET UP AUDIT DIAGNOSTICS MODE System set up audit diagnostics mode is entered when the vender inner door is open and the service switch is pressed The display will show a list of error codes for errors that have occurred since the door was last opened JC is a jammed column 55 is a select switch problem EN is an enable error board component failure To acknowledge an error press any select button at this time you will enter the menu The displr will show HD at this time Some of the menu items have sub menus To move through the menus and sub menus follow these instructions To n Line THROUGH MENU Press select buttons 1 8 2 simultaneousiv to scroll down throug
70. r delete selections A Press the service switch The display will show ADD indicating selections will be added Press the service switch again and the display will show DEL indicating selections will be deleted B Press and hold any select button The display will show ADD or DEL where is a select button number While holding a select button the will increment from 1 to the maximum select button number and return to 1 Release the select button when the desired selection to be added or deleted is displayed A message will scroll across the display telling you what selection will be added or deleted D Press service switch to complete the decision NOTE Only one selection may be added or deleted at a time The service switch must be pressed before and after each change Important Promotional sales when enabled will be on at all times of the day Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu ECNT ELECTRONIC COUNTER This function is used to show historical total vends historical product counts that have occurred for prices being used and interval product count for each selection from outside the vender To program the SIID to use this function press any select button The current setting or four 4 key programming will be displayed If no code is programmed To program or to change four 4 key program A Press service switch Display will show
71. rd VEND MOTOR The Vend Motor one for each vending stack is mounted on a bracket at the front of the Front Mechanism Plate The Vend Motor is in the Vend Motor Coil Circuit The Vend Motor runs when a normallv closed contact of the Select Switch pushed opens and signals the SIID Controller Board to run the Motor The Vend Motor continues to run via the SIID Controller Board while the Vend Motor Switch is on high side of Cam The Vend Motor stops when the Vend Motor Switch Arm drops off the high side of the Vend Motor Cam and the normally closed contact of the Vend Motor Switch closes signaling the SIID Controller Board to stop power to the Vend Motor Coil Circuit VEND MOTOR SWITCH All Columns A VEND MOTOR SWITCH The Vend Motor Switch one 1 for each circuit is located on the Vend Motor Assembly and secured by two 2 screws The normally closed contact of the Vend Motor Switch is in the Vend Motor Coil Circuit This normally closed contact opens in the Vend Motor Coil Circuit to keep the Vend Motor running via the SIID Controller Board until the Arm of the Vend Motor Switch drops in the Cam notch and the Vend Motor stops The normally open contact of the Vend Motor Switch has no function VEND MOTOR WIDE COLUMN Mounted on the Vender with the Vend Switch on the left side See Fig 3 The Linkage and Drive Arm assembly is used to connect the Vend Motor to the Oscillator See Fig 4 Vend Motor Switch 804 100 730 01 Nylin
72. ree vend counter Press select buttons 1 amp 2 simultaneously to move to the next item on the menu DST DAYLIGHT SAVINGS TIME This function is used to turn the DST option on or off To show current DST condition Press any select button and the display will show the current setting To change the DST condition Press amp hold Select Button 1 to turn DST on Display will show ON Press amp hold Select Button 2 to turn DST off Display will show OFF Press amp hold Select Buttons 1 amp 2 simultaneously to move to the next item on the menu DSTR DAYLIGHT SAVINGS TIME RULES This function is used to set the DSTR as it applies to American time or European time To show current DSTR condition Press any select button and the display will show the current settings To change the DSTR condition Press 8 hold Select Button 1 to turn DSTR to American rule for daylight savings time set clock back one hour on the last Sunday of October 2 00am set clock ahead 1 hour on the first Sunday in April 2 00am The display will show AMER Press 8 hold Select Button 2 to turn DSTR to European rule for daylight savings time set clock back 1 hour on the last Sunday in October 1 00am set clock ahead 1 hour on the last Sunday in March 1 00am The display will show EURO Press and hold Select Buttons 1 8 2 simultaneously to move to the next item on the menu SCE SMALL COIN TYPE ENABLE Mdb Coin Mec
73. relay is a device that connects the start winding of the compressor during start up The additional winding start helps the compressor motor come up to speed Once it reaches speed the starting relay disconnects the start winding from the circuit Dixie Bus LCD LED MDB NAMA UCS UCC GLOSSARY Direct Exchange of Data Dixie Narco Serial Communication Specification to allow Dixie Narco to add extra features without affecting current vender designs Infrared Liquid Crystal Diodes Light Emitting Diodes Multi Drop Bus Coca Cola Serial Communication Specifications Used in all Dixie SIID can venders National Automatic Merchandising Association Uniform Communications Standards Uniform Code Council MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC TABLE OF CONTENTS Door Exterior rsru etas nes 4 Door 7 Pull ele Eelere in 10 Select Panel Coin Insert Panel Page 12 Lu dl a ELE Page 15 Wiring SS euet 6 amu Page 16 Inner Djojo 18 Two Bar Linkage Nut Retainer Housing Page 20 Hingesand nee Page 21 Cabinet Interior EE Pages 24 Cabinet and Vend Pages 27 nde erte System s ac
74. s adjustable bv hand slide into the holes in the column wall for cans and other package settings Note Rear Spacers with Springs are not shown See Fig 13 the Latch Fingers are in the open position with the Lock Tabs disengaged See Fig 14 the Latch Fingers are in the closed position with the Lock Tabs engaged Make sure the tabs are in a locked position as shown before loading the Vender FOR REFERENCE ONLY Rear Spacer adjustment holes located in the sidewalls of the stacks CLEANING THE VENDER DO NOT USE A WATER JET OR NOZZLE TO CLEAN THE VENDER WHAT TO CLEAN SIGN FACE The polycarbonate sign face requires proper cleaning to prolong the service life of this item It is recommended that you periodically clean the sign face as follows 1 Rinse the sign with a soft cloth or sponge soaked in warm water 2 If necessary use mild soap to loosen any dirt or grime To prevent damage DO NOT SCRUB use a brush or squeegee as some signs have a clear ultraviolet resistant coating to prevent yellowing 3 Repeat the above steps as necessary then dry using a soft cloth to prevent spotting CABINET 1 Wash the cabinet with a good detergent or soap mixed in warm water 2 Wax the vender often with a good grade of automobile wax 3 corrosion inside the vender should be removed with fine steel wool and the area should be painted with aluminum paint 4 Repair any scratches on painted surfaces to prevent corrosion WARN
75. s the customer the price of any selection when that particular select button is pressed If all selections are set at the same price in primary set price and the same price in secondary set price the vend price is displayed at all times on the display Single Price or Multi Price via Select Panel or Hand held Prices for each selection are programmed either through the front select panel or through the DEX hand held device For single price configuration each selection has to be programmed for the same price Accounting Data Provided The accounting features are accessed through the front select panel These include CASH historical cash data which is not resettable CLN resettable cash data SALE historical vend data and SLN resettable vend data CASH Historical Data The total cash collected by the vender CLN Resettable Data The total cash collected for each selection SALE Historical Data The total number of vends by the vender SLN Resettable Data The total number of vends for each selection The types of data that can be retrieved via the DEX interface to a hand held device is addressed in the SIID Audit Features section Limited Access on Selection Time Days Price The limited access feature allows each selection to be inhibited with respect to time and selected days of the week Also prices of selections can be altered Happy Hour with respect to time and selected days of the week Multiple Co
76. scellaneous Worldwide Non Returnable Bottle Shimming Wide Stack Series 90 TB 474 Miscellaneous Worldwide Plastic Bottle Shimming Wide Stack Series 90 TB 475 Miscellaneous Worldwide Can Shimming Wide Stack Series 90 TB 476 Miscellaneous Worldwide Returnable Bottle Shimming T Models For shimming of venders or products not listed in the above Technical Bulletins call the Dixie Narco Service Department or contact vour Dixie Narco Representative CAMS FOR VEND MOTORS 1 Adjustable Cam For 2 Vending Cam For DNCB 1 deeper wide column DNCB 1 deeper single double depth b DNCB T models single double wide column or triple depth wide column b DNCB T models single depth wide column c Color of Cam is Gold c Color of Cam is Blue d Part 801 806 400 11 d Part 801 806 390 41 3 Vending Cam For 4 Adjustable Cam For a DNCB T models double 1 deeper narrow column or triple depth wide column b DNCB T models single double or b Color of Cam is Green triple depth narrow column c Part 801 806 410 41 c Color of Cam is Brown d Part 801 806 610 21 5 Vending For DNCB deeper narrow column b T models single double or triple depth narrow column c Color of Cam is Brown d Part 801 806 180 21 CAM INSTALLATION AND REMOVAL TO Select the Vending Cam required See 39 E Locate the Hub at the center of the Cam See Fig 6 3 With
77. sy A B Plastic Bearing 22222201 901 803 71 1 Bushing Inner Door L 801 806 42 1 801 806 42 1 Bushing Retainer Inner Door EEI 801 806 43 1 2 2 2 Inner Door Hinge Assv i Screw Phil Pan w out Washer 8 18 gt 900 301 50x x1 Screw Machine Truss 10 32 900 201 14x x1 Screw Phil Pan Sems 48 18 2 900 301 65x x1 Screw Phil Pan 6 20 800 303 22x x1 BEER BEE Keps Nut 10 32 900 800 65x x1 fF C Carriage Bolt 20 1 900 201 23x x1 169 051 10x x3 DIXIE NARCO INC COCA COLA MARKETING MACHINE SERVICE MANUAL MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC TWO BAR LINKAGE NUT RETAINER HOUSING 79 Wide 72 Wide 72 Narrow Linkage and Drive Arm Assy All Styles 2A Groove Pin 1 8x1 3 16 30mm T2 All Styles 900 901 94x x1 900 901 94x x1 B Drive Am Zi Er ger A All Styles 801 200 95x x1 801 200 95x x1 Fa B Nyiner Boom p e ec oe P Linkage Am Zinc EE All Styles 801 201 59x x1 801 201 59x x1 N N N N N N 5A Assy Nut Retainer Housing 1 point lock EES eege 432 052 50 4 432 052 50 4 432 052 50 4 B Traditional Nut Retainer Housing 1 point lock aa C Nut Traditional T point Toc ee Ng s Te EE RR oi eT Styles Standard All Styles High Security AT e
78. t have value of that pulse the note factor programmed in the vender The SIID will determine the value of the note inserted bv multiplying the number of pulses counted by the Note Factor programmed To show the current Note Factor condition Press any select button and the current value will be displayed To change the Note Factor NE condition Press and hold any select button The Note Factor will increment or decrement from 100 to 10 000 To change from increment to decrement release the select button and press it again Note 100 is 1 00 in domestic use NOTE The decimal point position will be communicated by the coin mech to SUD control board Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu CR CHANGE RULES for use with foreign L Plus coin mechs only Some countries have coin mechs that do not use all three coin tubes This would not allow the SIID to come out of exact change mode To accommodate this the Change Rules section allows the SIID to be programmed to use the tubes necessary for the SIID to not be in an exact change mode To show the current Change Rules condition press any select button and the display will show ABC indicating tubes A B and C must have change A refers to the tube on the left C refers to the tube on the right and B refers to the tube in the middle To change the Change Rule Condition Select Button 1 When pressed enables and
79. t item on the menu DSP Display Test Press any select button and the display segments will illuminate in a scrolling manner while blinking the exact change LED Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu VERS Version of Software Press any select button and the display will scroll the software revision level in the control box Example represents the installed software revision Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu Vender Identification Press any select button and the display will show the vender type that software has determined based on the select panel harness input The vender types are 00 Coke Venders 01 Pepsi and Press 8 hold select buttons 1 8 2 simultaneously to move to the next item on the menu RTN RETURN TO MAIN MENU Press 8 hold select buttons 1 8 2 simultaneousiv to return to 5 Press 4 hold select button 1 to return to DIAG Press 8 hold select buttons 1 8 2 simultaneously to move to the next item on the menu AUTO Auto Testing This function is used in Dixie Narco s manufacturing process and is not intended for use in the field lis purpose is a self test routine to check the SIID components listed For further details contact Dixie Narco Factory Service A Control Box D Motors Vend Switches B Select Switch Harness E Note Acceptors C
80. te de da a Pages 31 Electronic CON PONS a a Page 35 ee eed a 38 Washers Bolts 8 Miscellaneous Hardware Pages 40 MARKETING MACHINE SERVICE MANUAL MAIN DOOR EKTERIOR DIXIE NARCO INC ITEM DESCRIPTION PART NUMBER Coke Marketing Machine Door Assv 72 Wide 13 S3D 72 Narrow 13 530 79 Wide 13 830 72 Wide 9 20 72 Narrow 9 520 79 Wide 9 20 Marketing Machine Door Weld Assv 72 Wide 72 Narrow 79 Wide Protective Plate Door 72 Wide Narrow 79 Rain Guard 72 and 79 Wide 72 Narrow Horizontal Trim Bottom Wide Bottom Narrow Control Panel Wide Control Panel Narrow IN 624 050 20x x3 Bar cm nj 165 150 33x x3 165 150 33 3 164 150 33 3 EEE 164 151 14x x3 169 050 34x x3 ee 801 810 65x x1 801 810 65x x1 801 810 65x x1 624 050 00x x3 801 810 65x x1 Hinged Top Sign Trim Assy 72W 72N 79W 801 810 66 1 Locking Bar a P Tea 6 801 810 86 1 Assv Bracket Sign Cap Den W A Port Trim Spacer EA 805 700 95x x1 Trim Port Spacer neh Vertical Trim Left and Right 801 810 63x x1 Center 801 810 64 1 ia a sasi MARKETING SERVICE MANUAL DIXIE NARCO INC ITEM DESCRIPTION PART NUMBER 10 Ad
81. the cam position and empty detection is located on the controller board Low Voltage Select Panel The select panel consists of gold cross point switches The interface circuitry is located on the controller board The controller board supports up to 10 selections Programmable Space Sales Programmable space to sales is a feature which allows columns to be assigned to select buttons Columns dispensed evenly when more than one column is assigned to a select button or group of select buttons Select Panel Controller Programming or Hand held Controller Programming The SIID vender has the capability to be programmed through the select panel The SIID vender can also be programmed through the DEX port with the same hand held used to access the accounting data LED Display Light Emitting Diodes Optional LCD Display Liquid Crystal Diodes Early displays consist of 4 characters utilizing 7 segment LEDs for each character to provide a true alpha numeric display Future display boards will consist of four fourteen segment LEDs to provide clearer alpha numeric characters The display is implemented on it s own printed circuit board Sold Out Message Selection Each selection is supported by a sold out message When a given selection is sold out and that selection is pressed SOLd Out will scroll across the display Price Displayed when Selection is pressed The operation of the vender in the ready mode provide
82. through the menu from top to bottom B Press select button 1 to move left or right in the menu depending on the menu prompt on displav ELECTRICAL PARTS AND FUNCTIONS CORRECT CHANGE LAMP Correct Change Lamp The Correct Change Lamp is mounted in the Coin Insert Casting The Correct Change Lamp is controlled bv the SIID Controller board and is OFF when coins are in the tubes of the Coin Changer SELECT SWITCH Select Switch The Select Switch is located in the Select Panel behind the Select Button and is secured with two 2 screws The normallv closed contact of the Select Switch is in the SIID Control Board and Vend Motor Coil Circuits This normallv closed contact opens and the SIID Control Board Circuit completes the Vend Motor Coil circuit The normally open contact of the Select Switch has no function SOLD OUT SWITCHES The Sold Out Switch is located on the Front Mechanism Plate under the Vend Motor Cover The Sold Out Switch is the snap in type To install place the switch in position over the opening in the Front Mechanism Plate push in and at the same time slide to the right Vend Sold Out Switch The normallv closed contact of the Sold Out Switch has no function The normallv open contact of the Sold Out Switch is in the Sold Out Circuit kept open bv a can or bottle When not kept open bv a can or bottle the normallv open contact closes and completes the Sold Out Message Circuit via the 510 Controller Boa
83. tion for the vender SALE which is the historical total number of vends for the vender SLN which is the resettable total number of vends for each selection for the vender The audit data is accessed by pressing select button 4 when CASH or SALE is on the display With CASH on the display press select button 2 to scroll into CLN With SALE on the display press select button 2 to scroll into SLN ELECTRONIC ACCESS A much more extensive amount of audit information is accessible electronically It is retrieved with a portable data collection device and typically loaded into a computer at a central location The data can then be tracked with a data base for preparing route stocking lists tracking cash flow doing inventory control and other tasks Data collection devices are available from several sources including Norand Fujitsu Panasonic Telxon Verifone and Mars Dixie Narco currently collects data with a PC program running on a portable notebook computer The SIID uses the DEX UCS protocol as the method of exchanging data with the portable data collection device DEX UCS was formally adopted as the standard method of collecting audit data for the vending industry by the National Automatic Merchandising Association NAMA in April of 1991 DEX UCS has been used in related industries since 1989 It was developed by the Arthur D Little Company and is administered and maintained by the Uniform Code Council UCC The NAMA Vending
84. u TIME TIME To display time press and let go of any select button Time will be displayed in military time 24 hour clock To change time press and hold select button 1 or 2 the time will increment or decrement To change from increment to decrement release the select button and press it again To change time Press amp hold Select button 1 set hours Press amp hold Select button 2 set Minutes Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu DATE DATE To view date press and let go of select button 1 or 2 to display month and day Month and day will be displayed as X YY where X represents the month and YY represents the day Press and let go of button 3 to display day of week press and let go of button 4 to display year change Press amp hold Select Button 1 set Month Press amp hold Select Button 2 set Day Press amp hold Select Button 3 set Dav Of Week Sundav 1 Thursdav 5 Mondav 2 Fridav 6 Tuesdav 3 Saturdav 7 Wednesdav 4 Press hold Select Button 4 set Vear Press 8 hold select buttons 1 8 2 simultaneously to move to the next item on the menu 5 ESCROW This section supports 4 four escrow options To show current escrow condition press any select button To change the escrow condition Press 8 hold Select Button 1 Pr Escrow to Price The escrow condition is escrow to price All dollar bills will be stacked
85. ve to the next item on the menu 1 Motor Test Use this test to run any motor in the stack Use the following select buttons to run this test Select Button 1 Press until desired motor to run is shown on the display Select Button 2 Press to run the selected motor The display will show TESTING and the selected motor will run Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu CM Coin Mech Test Use this test to check coin mech programming coin chute work and coin mech payout systems Insert coins The value of coins will be reflected on display Press amp hold Select Button 1 Displays the Coin Mechanism setting MM Micro Mech interface Lt L Plus interface MDB Multi Drop Bus interface Press amp hold Select Button 2 Returns the coins inserted Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu Note Acceptor Use this test to check acceptor functions Insert note The value of note will be reflected on display Press amp hold Select Button 1 Displays the Note Acceptor setting LL low level HL high level or MDB multi drop note acceptor Press amp hold Select Button 2 Stacks the note and cancels the credit shown on display Press amp hold Select Button 3 Returns the note and cancels the credit shown on display Press amp hold select buttons 1 amp 2 simultaneously to move to the nex
86. vertise Window e xx 72 Wide and 72 Narrow 805 025 32x x1 79 Wide 805 025 31x x1 Port Panel IAE Wide Narro LIILZ Main Door Assy Top Assy Bottom Bi ea Advertise Window Right Side Door 72 ES pe Port Panel AA AA AE Be Sem Pa Pan wn WE Phil Pan w out Washer 8 18xV2 m 1 00000000 Nut 4 20 Hex Nut Center w Flange 16 18 top hinge drop in eee ee TERA 22 21 8 32x1 900 400 41x x1 T Bolt 88 32 3 900 400 35x x1 T Bolt 8 32x1 2 900 400 45x x1 AA PAS Carriage Bolt Y4 20xV2 900 201 45x x1 Carriage Bolt 7 6 18 1 top hinge drop 900 201 85x x1 a Al N Lor Pop Rivet Steel Zinc Plated 901 100 61x x1 S NES Chrisimas Clip 354280307 00 900 902 13 1 MARKETING MACHINE SERVICE MANUAL DIXIE NARCO INC E MARKETING MACHINE SERVICE MANUAL MAIN DOOR INTERIOR DIXIE NARCO INC ITEM DESCRIPTION PART NUMBER Deliverv Port Large Port 2 Deliverv Port Spacer Large Port p W A Trim Spacer Right Side Left Side 3 Port Stiffener PEA Wide Narrow 4A Access Door prior to 6506AX Wide Narrow 4B Access Door hinged 0001 6506 and higher Pe Wide Narrow 5 Hopper Door Rod Wide Narrow 7 Door Hinge S Bottom C
87. y to be removed NOTE Only one secondary pricing on days may be made at a time The service switch must be pressed before and after each change Press amp hold select buttons 1 amp 2 simultaneously to move to the next item on the menu RETURN This function is used to return to the User Options Menu Press select buttons 1 amp 2 simultaneously to return to S P2 Press select button 1 to return to SEC Press select buttons 1 amp 2 simultaneously to move to the next item on the menu ACD SET ACD AUDIT BOX Note This feature is available in specific software rev levels only This function is used to support the Greenwick Audit Box features when enabled To view ACD setting press and release select button 1 display will show ENABLED or DISABLED To change from ENABLED to DISABLED press and release select button 1 Press select buttons 1 amp 2 simultaneously to move to the next item on the menu FREE FREE VEND ENABLE This function is used to allow 5 6 and 8 column venders to be set on free vend using a mechanical switch The free vend enable must be turned on for the switch to allow free vend and a free vend switch kit 491 742 600 04 must be installed using installation instructions E004 X from Dixie Narco Press Select Button 1 Toggle free vends on ENABLED and off DISABLED Press Select Button 2 To display the number of free vends Press Select Button 3 To clear or reset the f

Download Pdf Manuals

Related Search

Related Contents

Agilent 3395 Integrator  La BD s`anime à ODysseum - Montpellier Méditerranée Métropole  User Manual - Nancy`s Knit Knacks  （2008年5月9日発行）PDFを見る  RK3639K - Menards  Taximeter  Commander  Page 1 Page 2 Page 3 Page 4 ー 安全上のご注意 安全にお使い  

Copyright © All rights reserved. Failed to retrieve file