Operation and Service Manual
Contents
1. Description Designator 1 16044 60001 2 CONN BNC SMB 2 3050 0067 4 WSHR FL MTLC 3 3050 0789 4 WSHR FL NM 4 16047 40002 4 INSULATOR 5 1253 0476 2 ADPT BNC SMB 26 Chapter 5 Figure 5 3 Replacable Parts part 3 of 4 Service Maintenance Table 5 3 Replacable Parts part 3 of 4 Reference Agilent Part No Qty Description Designator 1 16047 24021 2 KNOB 2 16048 04021 1 COVER TOP 16048G 16048 04025 1 COVER TOP 16048H 3 16047 24026 2 FLANGE 4 0515 0914 4 SCR MACH M3X0 5 5 0515 0952 4 SCR MACH M2X0 4 6 16048 00624 1 ANGLE 7 0515 0914 3 SCR MACH M3X0 5 Chapter 5 27 Table 5 3 Figure 5 4 Service Maintenance Replacable Parts part 3 of 4 Reference Agilent Part No Qty Description Designator 8 16048 04022 1 COVER BOTTOM 9 16048 00625 1 ANGLE Replacable Parts part 4 of 4 Table 5 4 Replacable Parts part 4 of 4 Reference Agilent Part No Qty Description Designator 1 1250 1985 4 CONNECTOR BNC 2 16048 00621 1 PLATE 3 2190 0016 4 WASHER 4 2950 0043 4 NUT HEX DBL CHAM 5 16380 24001 4 TERMINAL 6 42036 00601 2 PLATE 7 3050 0893 4 WASHER 8 0535 0043 4 NUT 28 Chapter52. load data measurement is completed the softkey label changes to LOAD DONE 10 Press done key Chapter 3 19 Operation Performing Fixture Compensation Performing Fixture Compensation To compensate stray capacitance and residual impedance fixture compensation should be performed When you use the optional BNC Bracket Agilent P N 16048 60003 or an user fabricated test fixture fixture compensation is required Refer to the 4294A Operation Manual for the fixture compensation procedure 20 Chapter 3 Specifications This chapter provides specifications of the 16048G H Test Leads 21 Specifications Specifications Specifications Applicable Instruments LCR meters and Impedance Analyzers with four terminals Maximum Voltage 42V peak max AC DC Operating temp 20 C to 150 C Environment Exclude up to 20 cm from four terminal pair connection block humidity 15 to 95 RH E wet bulb temp lt 40 C Non Operating temp 40 C to 70 C Environment humidity lt 90 RH wet bulb temp lt 65 C Cable length Nominal 1 m 16048G 2 m 16048H Weight Approximately 460 g 16048G Approximately 690 g 16048H Safety Standards EN61010 1 1993 A2 1995 IEC61010 1 1990 A1 1992 A2 1995 CSA C22 2 No 1010 1 1992 INSTALLATION CATEGORY I POLLUTION DEGREE 2 INDOOR USE 22 Chapter 4 Service This chapter provides information on servicing and prope
3. to connect the 16048G or 16048H to the 4294A Set the 16048G H to the test connectors on the front panel of the HP 4294A by gradually coupling the four BNC connectors and fastening screws of the fixture with the test connectors and accessory mounting holes of the instrument until they come to complete contact Fasten two of the four BNC connectors to the mating test connectors by gradually turning the BNC connectors rotation levers until each pair of connectors are securely connected Be sure to align the grooves on both sides Turn clockwise the fixture s two fastening screws together so that the fixture is secured to the instrument Finally secure the remaining two BNC connectors of the fixture by turning clockwise their rotation levers Connecting the fixture to the instrument 16048ghoj0101 NOTE Using the connection block securing screws enables the 16048G H to connect the GND of the 4294A Chapter 1 11 Installation Guide Connecting the 16048G H 12 Chapter1 Overview Overview Product Overview AAA Product Overview The 16048G H consists of a direct attachment 4 terminal pair interface which is equipped with four BNC f connectors These test leads are used to attach user fabricated test fixtures Cable len
4. Agilent 16048G H Test Leads Operation and Service Manual Third Edition Spb Agilent Technologies Agilent Part No 16048 90050 January 2001 Printed in Japan NOTE Notices The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the Agilent Technologies Agilent Technologies Japan Ltd Component Test PGU Kobe 1 3 2 Murotani Nishi Ku Kobe shi Hyogo 651 2241 Japan Copyright Agilent Technologies Japan Ltd 1999 2001 Manual Printing History The manual s printing date and part number indicate its current edition The printing date changes when a new edition is printed Minor corrections and updates that are incorporated at reprint do not cause the date to change The manual part number changes when extensive technical changes are incorporated April 1999 First Edition part number 16048 90050 December 1999 Second Edition part number 16048 90050 January 2001 Third Edition part number 16048 90050 Safety Summary The following general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific WARNINGS elsewhere in this manual may impair the protectio
5. NOTE For adapter setup use the 100 Q Resistor furnished with the 4294A Agilent P N 04294 61001 1 More than 30 minutes warm up time is required after turning on the 4294A 2 Press Cal key to bring up the Calibration Menu 3 Press ADAPTER key to bring up the adapter setup Menu shows current settings 4 Select 4TP 1M in the case of 16048G 4TP 2M in the 16048H When the selection is completed the softkey label will be underlined 5 Press SETUP key to bring up the Adapter Setup Menu 6 Connect the Lcur terminal and Lpot terminal on the 16048G or 16048H to the Hpot terminal and Hcur terminal of the 100 Q Resistor furnished with the 4294A The Hcur and Hpot terminal on the 16048G H should remain open nothing should be connected Figure 3 1 Connecting 100 Q Resister Phase Compensation Data Measurement 04294 61001 100 Q RESISTOR 160489h0 0301 18 Chapter 3 Figure 3 2 Operation 4294A Setting 7 Press PHASE COMP key to start the phase compensation data measurement About 1 minutes later phase compensation data measurement is completed and the softkey label changes to PHASE COMP DONE 8 Connect the Lcur Lpot Hcur Hpot terminal on the 16048G or 16048H to the Lcur Lpot Hcur Hpot terminal of the 100 Q Resistor respectively Connecting 100 Q Resister Load Data Measurement 04294 61001 100 RESISTOR 16048ghoj0302 9 Press LOAD key to start the load data measurement When the
6. ce agreements are available for Agilent Technologies products For any assistance contact your nearest Agilent Technologies Sales and Service Office Addresses are provided at the back of this manual Safety Symbol General definitions of safety symbols used on the instrument or in manuals are listed below Instruction Manual symbol the product is marked with this symbol when it is necessary for the user to refer to the instrument manual Alternating current Direct current On Supply Off Supply In position of push button switch Out position of push button switch Frame or chassis terminal A connection to the frame chassis of the equipment which normally include all exposed metal structure This warning sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in injury or death to personnel This Caution sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in damage to or destruction of part or all of the product Note denotes important information It calls attention to a procedure practice condition or the like which is essential to highlight Contents 1 Installation Guide Incoming Inspection ir LL ee Li 10 Connecting the 16048G H ico de A a ER Aa 11 2 Overview Product Overview a BA na ed d
7. gth of the 16048G is 1 meter the 16048H is 2 meter Figure 2 1 Product Overview 16048ghoj0201 14 Chapter 2 Overview Functions Functions Figure 2 2 shows name of each part of the 16048G H and Table 2 2 shows their function Figure 2 2 16048G H Parts 1 Instrument Side Connection Block 2 Connection Block Securing Screw 3 Ground Lead 4 DUT Side Connection Block 5 Mounting Plate 16048ghoe0202 Table 2 1 16048G H Function No NAME FUNCTION 1 Instrument Side Connect to the instrument s UNKNOWN terminal Connection Block Connection Block Secures the connection block to the 4294A Securing Screw Ground Lead Connect to the chassis or grounded part of the measurement target DUT Side Connection Used to attach BNC Bracket or user fabricated test Block fixtures Mounting Plate Mounts on the measurement target to stabilize the cable Chapter 2 15 Overview Functions Figure 2 3 Cable Assignment 16048ghoj0203 16 Chapter 2 Operation This chapter describes the proper methods for setting the 4294A fixture compensation with the 16048G H 17 Operation 4294A Setting 4294A Setting Before you begin your measurement you should perform the adapter setup in the 4294A Also refer to the operation manual of the 4294A about the adapter setup Adapter Setup Connect the 16048G H to the 4294A and perform the adapter setup described below
8. n provided by the equipment In addition it violates safety standards of design manufacture and intended use of the instrument The Agilent Technologies assumes no liability for the customers failure to comply with these requirements 16048G H comply with INSTALLATION CATEGORY I and POLLUTION DEGREE 2 in IEC61010 1 16048G H are INDOOR USE product WARNING e DO NOT Operate In An Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes Operation of any electrical instrument in such an environment constitutes a definite safety hazard e Keep Away From Live Circuits Operating personnel must not remove instrument covers Component replacement and internal adjustments must be made by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power cable removed To avoid injuries always disconnect power and discharge circuits before touching them e DO NOT Service Or Adjust Alone Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is present DO NOT Substitute Parts Or Modify Instrument Because of the danger of introducing additional hazards do not install substitute parts or perform unauthorized modifications to the instrument Return the instrument to a Agilent Technologies Sales and Service Office for service and repair t
9. o 14 FUNCHUONS A rs SI Re ile gee E A A RE Aa 15 3 Operation IS A lai aa ae 18 Adapter Seip a sorso loci see esse LI e BEST LR re 18 Performing Fixture Compensation o 20 4 Specifications Specifica tons en LAO Rae ede Sen ee 22 5 Service Maintenance a ad 24 Contents Installation Guide Table 1 1 Installation Guide Incoming Inspection Incoming Inspection Inspect the shipping container for damage If the shipping container or cushioning material is damaged it should be kept until the contents of the shipment have been checked for completeness and the 16048G H has been checked mechanically and electrically The contents of the shipment should be as listed in Table 1 1 If the contents are incomplete if there is mechanical damage or defect notify the nearest Agilent Technologies office If the shipping container is damaged or the cushioning material shows signs of unusual stress notify the carrier as well as the Agilent Technologies office Keep the shipping materials for the carrier s inspection Contents Description Part Number Qty Test Lead 16048G or 16048H Mounting Plate BNC Bracket 16048 60003 Operation and Service Manual 16048 90050 a Only furnished with option 001 10 Chapter1 Step 1 Step 2 Step 3 Step 4 Figure 1 1 Installation Guide Connecting the 16048G H Connecting the 16048G H Follow these steps below
10. o ensure that safety features are maintained e Dangerous Procedure Warnings Warnings such as the example below precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed Dangerous voltages capable of causing death are presenting this instrument Use extreme caution when handling testing and adjusting this instrument Certification Agilent Technologies certifies that this product met its published specifications at the time of shipment from the factory Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology to the extent allowed by the Institution s calibration facility or to the calibration facilities of other International Standards Organization members IMPORTANT Warranty This Agilent Technologies instrument product is warranted against defects in material and workmanship for a period corresponding to the individual warranty periods of its component products Instruments are warranted for a period of one year Fixtures and adapters are warranted for a period of 90 days During the warranty period Agilent Technologies will at its option either repair or replace products that prove to be defective For warranty service or repair this product must be returned to a service facility designated by Agilent Technologies Buyer shall prepay shipping charges to Agilen
11. r maintenance 23 Figure 5 1 Service Maintenance Maintenance An exploded view of the 16048G H for parts identification is shown in Figure 5 1 to Figure 5 4 Do not disassemble any further than shown Maintenance consists principally of cleaning contacts and replacing worn or damaged parts Take special care when cleaning contacts To order parts use the Agilent part numbers listed in Table 5 1 to Table 5 4 If a faulty part is located in an assembly that cannot be disassembled order the next higher assembly or return the fixture to the nearest Agilent Technologies Sales Service Office for repair or replacement Replacable Parts part 1 of 4 24 Chapter 5 Service Maintenance Table 5 1 Replacable Parts part 1 of 4 Reference Agilent Part No Qty Description Designator 1 16048 61620 1 CBL ASSY 16048G Excludes 2 3 4 5 6 16048 61623 1 CBL ASSY 16048H Excludes 2 3 4 5 6 2 1400 0493 4 CABLE TIE 3 9170 1465 1 CORE 4 1 CBL CLANP 5 0515 1550 1 SCR M3 L 8 P H 6 3050 0891 1 WASHER M3 7 2950 0035 4 NUT HEX DBL CHAM 8 2190 0102 4 WASHER 9 16048 00623 1 GUIDE 10 1250 0252 4 CONN RF BNC 11 16048 00626 1 PLATE 12 16048 00627 1 ANGLE 13 0515 1012 2 SCR FL M4L8 Chapter 5 25 Service Maintenance Figure 5 2 Replacable Parts part 2 of 4 Table 5 2 Replacable Parts part 2 of 4 Reference Agilent Part No Qty
12. t Technologies and Agilent Technologies shall pay shipping charges to return the product to Buyer However Buyer shall pay all shipping charges duties and taxes for products returned to Agilent Technologies from another country Agilent Technologies warrants that its software and firmware designated by Agilent Technologies for use with an instrument will execute its programming instruction when property installed on that instrument Agilent Technologies does not warrant that the operation of the instrument or software or firmware will be uninterrupted or error free Limitation Of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by Buyer Buyer supplied software or interfacing unauthorized modification or misuse operation outside the environmental specifications for the product or improper site preparation or maintenance No other warranty is expressed or implied Agilent Technologies specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Exclusive Remedies The remedies provided herein are buyer s sole and exclusive remedies Agilent Technologies shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any other legal theory WARNING CAUTION NOTE A NI l O mn O d Assistance Product maintenance agreements and other customer assistan
Download Pdf Manuals
Related Search