the Storm3 FFH User Manual
Contents
1. 69 70 Electrical system Electronics protection system The vehicle s electronics are equipped with an overload protection system If the motors are put under considerable strain for a longer period of time for example when driving up a steep hill and especially when the ambient temperature is high then the electronic system could overheat In this case the vehicle s power is reduced gradually until it finally comes to a halt The Status Display shows a corresponding error code see chapter Fehler Verweisquelle konnte nicht gefunden werden on page Fehler Textmarke nicht definiert By switching the power supply off and back on again the error code is cancelled and the electronics are switched back on It will take approximately five minutes until the electronics have cooled down enough for the motors to restore full power again When the motors are stalled by an insurmountable obstacle such as a high kerb and the vehicle driver allows the motors to strain against this hindrance for more than 20 seconds without moving then the electronics will automatically switch off to prevent the motors from being damaged The Status Display shows a corresponding error code see chapter Fehler Verweisquelle konnte nicht gefunden werden on page Fehler Textmarke nicht definiert By switching off and back on again the error code is cancelled and the electronics are switched back on The main fuse NOTE A defective main fuse may be2. rrrry aa 8 6 1 2 Setting the ANG i iki dy ee leet alek korinda aeei Eeen k eker ak elen ke we 8 6 1 3 Setting the end stop of the footrest i lkl k llilld dddidddi dak 8 6 1 4 Adjusting the length of the footrest iii Ek 8 6 2 Manually height adjustable legrest 90 0 oo ii 10 11 12 13 Swivelling the legrest outward and or removing ui keke 54 6 6 2 2 Getting the angle cats 5U yooo ean ut age aa iaaii 55 8 6 2 3 Setting the end stop of the le grest Eiiui EEE EEE kk kk kk kk 59 8 6 2 4 Adjusting the length of the legrest Liuii EEE kk kk kk kk kk 64 8 6 2 5 Adjusting the depth of the calf plate LLu LEE EEE kk kk k kk 65 8 6 2 6 Adjusting the height of the Calf plate L LEE EEE kk kk 66 8 6 2 7 Unlocking and swivelling the calf plate backward when alighting 67 8 6 2 8 Adjusting the angle adjustable foot plate L u ik 68 8 6 2 9 Adjusting the angle and depth adjustable foot plate ee eeeeeeeeeeeeeteeeeeeeeeees 69 Electrical system 70 9 1 Electronics protection system J k l l ll lli k kk kak kak k kk kk KAKE KA KAKE KAK AKA KA KAKA KAWA 70 Skt Me MAIN HUSO y kn erdal k Aya Kaleki d n kek UK M RA Ken vain ei d 11 9 2 Batteries E E A A E A r rrrrerergggWrerrggWWd 72 9 2 1 What you need to know about batteries Eiu kk kk kk k
3. Your wheelchair may be equipped with one of several different remotes For information on the different functions and how to operate a particular remote please see it s corresponding User Manual 33 8 1 8 1 1 34 Adjusting the wheelchair to the user s seating posture Adjusting the armrests and the control panel Adapting the control panel to the length of the user s arm e Loosen the wing screw 1 e Set the remote to the desired length by pushing forward or backward e Re tighten the screw 8 1 2 Setting the height of the remote e Loosen the wing screw 1 e Set the remote to the desired height e Re tighten the screw 35 8 1 3 Setting the height of the armrests W 36 nes ei Allen key 3 mm Use the Allen key 3 mm to loosen the screw 1 Set the armrest at the desired height Re tighten the screw Adjusting the width of the armrests The distance between the side sections can be adjusted by 5 5 cm on both sides 11 cm in total Requirements e Allen key 8mm Where to find the adjustment screws The picture below shows the position of the screws 1 that enable adjustment to the width of the armrests 37 38 Doing the adjustment Loosen the screw 1 Set the armrest in the desired position Re tighten the screw Check that the armrest is fastened firmly Repeat the procedure for the other armrest 8 2 Adjusting the seat angle seat height 8 2
4. e Inspection according to service plan Please consult service instructions available from Invacare e Adaptation to the user Please see chapter Adjusting the wheelchair to the user s seating posture on page 34 89 14 90 Disposal e The equipment wrapping is potentially recyclable e The metal parts are used for scrap metal recycling e The plastic parts are used for plastic recycling e Electric components and printed circuit boards are disposed of as electronic scrap e Exhausted or damaged batteries can be returned to your medical equipment supplier or Invacare e Disposal must be carried out in accordance with the respective national legal provisions e Ask your city or district council for details of the local waste management companies 15 Technical specifications Permissible operating and storage conditions Temperature range for operation e 25 50 C according to ISO 7176 9 Temperature range for storage e 40 65 C according to ISO 7176 9 Electric System Motors e 2x 350W Batteries e 2x12 V 70 Ah C20 leakproof gel Main fuse e SOA Output current 8 A 8 Output voltage 24 V nominal 12 cells Input voltage 200 250 V nominal Operating temperature surroundings 5 40 C Storage temperature 20 50 C Drive wheel tyres Tyre type e Trelleborg 8x3 00 pneumatic Tyre p
5. If driving on such a surface is inevitable then always drive slowly and with the utmost caution Never attempt to overcome an obstacle when on an uphill or downhill gradient Never attempt to drive up or down a flight of steps with your wheelchair When overcoming obstacles always observe the maximum obstacle height see chapter Technical specifications from page 91 and information about overcoming obstacles in chapter Taking Obstacles from page 29 Avoid shifting your centre of gravity as well as abrupt joystick movements and changes of direction when the wheelchair is in motion Never use the wheelchair to transport more than one person Do not exceed the overall maximum permissible load or the maximum load per axle see chapter Technical specifications on page 91 Note that the wheelchair will brake or accelerate if you change the Driving Mode whilst the wheelchair is in motion 21 22 Danger of breaking down in adverse weather conditions i e extreme cold in an isolated area e Ifyou are a user with severely limited mobility we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion e Make sure each time before you drive the wheelchair that your feet are squarely and securely in place on the footplates and that both legrests are p
6. 1 Manual adjustment using perforated plates There are three perforated plates underneath the seat for adjusting the seat angle and the seat height These perforated plates in connection with the adjustable rear holding plates result ina multitude of different setting possibilities The adjustment range of the seat height is 42 5 cm to 50 cm The adjustment range of the seat angle is 22 Please note The higher the seat setting the smaller the adjustment range of the seat angle Pre requisites ang e 5mm Allen key e 6mm Allen key e 13mm open ended spanner e Torque wrench 39 40 e The picture at right shows the position of the perforated metal plates 1 and the fixation bolts 2 of the retaining plates for adjusting the seat height and seat angle The picture at right shows the front perforated metal plates The procedure is similar for the rear perforated metal plates To adjust the front perforated metal plates an open end spanner 13 mm is needed in addition to the Allen key 5 mm e To adjust the seat height seat angle loosen and remove the bolt 1 using the spanner e Adjust the perforated metal plates to the desired height angle e Re position the bolts again and tighten with the spanner to 40 Nm Additionally the seat height and angle can be adjusted using the rear retaining plates L e Loosen the rear fixation bolt on one side in E 4 threaded bushing 1 so that the retaining plate can
7. As an alternative you can use a platform lift Ensure that the total weight of the mobility device including the user does not exceed the maximum permissible weight for the platform lift or winch if you are using Danger of injury if maximum permissible load is exceeded e Do not exceed the maximum permissible load see chapter Technical specifications from page 91 e The mobility device is only designed for use by a single occupant whose maximum weight does not exceed the maximum permissible load of the device Never use the mobility device to transport more than one person 17 18 Danger of injury due to wrong lifting or dropping of heavy components e When maintaining servicing or lifting any part of your mobility device take into account the weight of the individual components especially the batteries Be sure at all times to adopt the correct lifting posture and ask for assistance if necessary Danger of falling out of the mobility device e Do not slide forward on the seat do not lean forward between your knees do not lean backwards out over the top of the backrest for example to reach an object e Ifa posture belt is installed it should be correctly adjusted and used each time you use the mobility device e When transferring to a different seat position the mobility device as close as possible to the new seat Danger of injury by moving parts e Make sure that no injury is incurred by moving parts of the mobilit
8. Only ever use the battery type defined in the technical specifications see Technical specifications on page 91 Danger of fire and burns if battery terminals are short circuited e DO NOT short circuit battery terminals with a tool WARNING Corrosion and burns from acid leakage if batteries are damaged e Remove clothes that have been soiled by acid immediately After contact with skin e Immediately wash affected area with lots of water After contact with eyes e Immediately rinse eyes under running water for several minutes consult a physician 9 2 3 1 Removing the batteries amp CAUTION Risk of fire and burns if battery poles are bridged e When replacing the batteries the battery poles MUST NOT come into contact with metal parts of the wheelchair causing bridging e Be sure to replace the battery pole caps after the batteries have been replaced ii Pre requisites Rp i ae at a eg iy e 11mm open ended spanner e Remove the battery cover 78 Remove the plastic clips 1 pull the electronic device support backwards and upwards Pull the battery pole caps 1 upward and push back in order to reach the battery poles Use the open ended spanner to loosen the battery pole clamp 2 Flip the electronic device support upwards if necessary release the connecting plugs Pull out the batteries 9 2 3 2 How to handle damaged batteries correctly WARNIN
9. or added that have not been approved for this product by Invacare In this case the company that adds or replaces the components or accessories is responsible for the conformity assessment CE marking or for registering the wheelchair as a special design and for the relevant documentation 23 24 CAUTION Danger of injuries and damage to mobility aid due to unapproved components and accessory parts Seating systems additions and accessory parts which have not been approved by Invacare for use with this mobility aid can affect the tipping stability and increase tipping hazards e Only ever use seating systems additions and accessory parts which have been approved by Invacare for this mobility aid Seating systems which are not approved by Invacare for use with this power wheelchair do not under certain circumstances comply with the valid standards and could increase the flammability and the risk of skin irritation e Only use seating systems that have been approved by Invacare for this power wheelchair Electrical and electronic components which have not been approved by Invacare for use with this mobility aid can cause fire hazards and lead to electromagnetic damage e Only ever use electrical and electronic components which have been approved by Invacare for this mobility aid Batteries which have not been approved by Invacare for use with this mobility aid can cause chemical burns e Only ever use batter
10. s n Fax 34 0 972 49 32 20 ji Poligon Industrial de Celra contactsp invacare com E 17460 Celra Girona WWW www invacare es ESPANA CF Invacare Poirier SAS Route de St Roch F 37230 Fondettes France T Fax WWW 33 0 247 62 64 66 33 0 247 42 12 24 contactfr invacare com www invacare fr Ra Invacare Ltd Customer services 44 0 1656 77 62 22 E EB Pencoed Technology Park Fax Customer services 44 0 1656 77 62 20 Pencoed uk invacare com Bridgend CF35 5HZ WWW www invacare co uk United Kingdom T Invacare Mecc San s r l T 39 0445 38 00 59 Via dei Pini 62 Fax 39 0445 38 00 34 7 36016 Thiene VI italia invacare com ITALIA WWW www invacare it OE Invacare Ireland Ltd T 353 18 10 70 84 HE Unit 5 Seatown Business Campus Fax 353 18 10 70 85 ji Seatown Rd Swords ireland invacare com County Dublin WWW www invacare ie Ireland Invacare AS Grensesvingen 9 Postboks 6230 Kundeservice Fax Kundeservice 47 0 22 57 95 00 47 0 22 57 95 01 norway invacare com Etterstad island invacare com N 0603 Oslo WWW www invacare no Norge i NU Invacare B V T 31 0 318 69 57 57 Celsiusstraat 46 Fax 31 0 318 69 57 58 j NL 6716 BZ Ede nederland invacare com Nederland csede invacare com WWW www invacare nl po Invacare Lda T 351 225 10 59 46 FP Rua Estrada Velha 949 T 351 225 10 59 47 P 4465 784 Le a do Balio
11. two drill holes in the backrest frame and one of the sechs drill holes in the fixation plate e Re position and tighten the screws 43 8 4 44 Adjusting the headrest e Loosen the clamping lever 1 2 or 3 e Adjust the headrest to the required position e Retighten clamping lever 8 5 8 5 1 Postural belts A postural belt is an option which can either be fixed to the wheelchair ex works or can be retrofitted by your specialist dealer If your wheelchair is fitted with a postural belt your specialist dealer will have informed you about fitting and usage The postural belt is used to help the wheelchair user keep an optimum sitting position Correct use of the belt assists the user in sitting securely comfortably and well positioned in the wheelchair especially for such users who do not have such a good sense of balance while sitting NOTE We recommend using the postural belt whenever the wheelchair is used The belt should be tight enough to ensure that you are sitting comfortably and that your body is in the correct sitting position Types of postural belts Your wheelchair can be fitted with the following postural belt types ex works If your wheelchair has been fitted with a different belt to those listed below please ensure that you have received the manufacturer s documentation with regard to correct fitting and use Belt with metal buckle adjustable one side Belt can only be adjusted on one
12. Da ji be swiveled upward or downward i 4 e Loosen and remove the front fixation bolt XE a 1 depending on the position the bolt is either Nu AA W located in threaded bushing 2 or 3 ae i e Repeat the procedure on the other side 2 e Low adjustment hole combination 1 and 2 e High adjustment hole combination 1 and 3 e Re position and tighten the screws re a a T a HT A Sa ka at at Fa i p ki OAY 41 42 The adjustable rear perforated metal plates have five positions These are indicated by the letters A to E in the illustration at right When the retaining plates are in the lower position see above then all five adjustments can be used In the high position only adjustments B C D and E are possible When using A the retaining plate collides with the seat frame This results in the following possible seat heights Retaining plate in the lower position Position of the perforated metal plate seat height A 45 5 cm B 47 cm C 47 cm D 48 cm E 48 5 cm Retaining plate in the high position Position of the perforated metal plate seat height B 42 cm at 6 seat angle C 50 cm D 51 cm E 53 cm 8 3 8 3 1 Adjusting the backrest Adjusting the backrest manually The angle of the backrest has six positions from 10 to 30 e Loosen and remove the knurled screws 1 on both sides e The backrest is adjusted by selecting a combination of one of the
13. Fax 351 225 10 57 39 Portugal portugal invacare com WWW www invacare pt ga terf rs ljare N S gt Invacare AB Fagerstagatan 9 Kundtjanst Fax Kundtjanst 46 0 8 761 70 90 46 0 8 761 81 08 sweden invacare com FIN S 163 91 Sp nga finland invacare com Sverige WWW www invacare se Tillverkare M LNDAL Invacare Deutschland GmbH T 46 0 31 86 36 00 KleiststraRe 49 Fax 46 0 31 86 36 06 D 32457 Porta Westfalica ginvacare invacare com Deutschland LANDSKRONA T 46 0 418 2 85 40 Fax 46 0 418 1 80 89 linvacare invacare com OSKARSHAMN T 46 0 491 1 01 40 Fax 46 0 491 1 01 80 oinvacare invacare com Eastern European Distributor a 49 0 5731 75 45 40 european Organisation EDO Fax 49 0 5731 75 45 41 countries KleiststraRe 49 edo invacare com D 32457 Porta Westfalica WWW www invacare de Deutschland Table of Contents Chapter 1 Introduction 1 1 Important symbols in this manual 0 0ccecceeseeeeeeeeee ee eeeeseeeee seen eases ceeeeeeeeeseeeeeenenees 1 2 Important symbols found on the vehicle sceceseseeeeeeeeeeeeeeeeeeeeeeeseeeseseeeeeseenesenes 1 3 Type classification and permissible USC csscsseeeeeeceeeeeeeeseeeeeeeeeeeseeseeeeeeeeeeees 1 4 GUAT AGIR GO innn Cr dikeye Oya E SEE DA ened cteaseaced NR EW AVANA KAK ERE ERKA HEWA HEK IAA E ARA KERR KERA R OK 1 5 INCI CALI ONS Dy rrr E EN NA 1 6 Life expectant DD r rr
14. G Corrosion and burns from acid leakage if batteries are damaged e Remove clothes that have been soiled by acid immediately After contact with skin e Immediately wash affected area with lots of water b gt After contact with eyes e Immediately rinse eyes under running water for several minutes consult a physician e Always wear safety goggles and appropriate safety clothing when handling damaged batteries e Place damaged batteries in an acid resistant receptacle immediately after removing them e Only ever transport damaged batteries in an appropriate acid resistant receptacle e Wash all objects that have come into contact with acid with lots of water Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare 79 80 Care and maintenance NOTE Have your vehicle checked at least twice a year by an authorised Invacare dealer in order to maintain it s driving safety and roadworthiness Cleaning the vehicle When cleaning the vehicle pay attention to the following points e Only use a damp cloth and gentle detergent e Do not use any abrasive or scouring liquids e Do not subject the electronic components to any direct contact with water e Do not use high pressure cleaning devices Disinfection Spray or wipe disinfection using a tested and recognised product is permitted A list of the current permitted disinfectants is ava
15. The depth of the calf plate can be adjusted via the holding plate The holding plate hole combinations allow 5 different depth settings le Pre requisites uv e 1x 10 mm open ended spanner e Use the open ended wrench to loosen the nut 1 and remove e Adjust to the desired depth Please observe that the round holes are intended for the calf plate retaining screw and the oblong holes for the aglet without thread e Screw the nut back on and tighten 65 8 6 2 6 Adjusting the height of the calf plate M J Pre requisites Ev e 1x4 mm Allen key e Use the Allen key to loosen the screws 1 e Adjust to the desired position e Re tighten the screws 66 8 6 2 7 Unlocking and swivelling the calf plate backward when alighting e Press the calf plate straight down e Unlock the legrest and swivel outward The calf plate swivels backward on its own 67 e Lift leg over the heel strap and place on the ground 8 6 2 8 Adjusting the angle adjustable foot plate bai Pre requisites M e 1x5 mm Allen key e Use the Allen key to loosen both set screws on the foot plate e Adjust to the desired angle e Re tighten the screws 68 8 6 2 9 Adjusting the angle and depth adjustable foot plate i Pre requisites 1x 5 mm Allen key Use the Allen key to loosen the set screw on the foot plate 1 Adjust the foot plate to the desired angle or depth Re tighten the screw
16. Yes you can Invacare Storm Competition FFH Power wheelchair User manual CE How can you get in touch with Invacare If you have any questions or need support please contact your authorised Invacare Dealer who has the necessary know how and equipment plus the special knowledge concerning your Invacare product and can offer you all round satisfactory service Should you wish to contact Invacare directly you can reach us in Europe at the following addresses and phone numbers TA Invacare Austria GmbH T 43 6232 5 53 50 AL Herzog Odilostrasse 101 Fax 43 6232 5 53 54 ji A 5310 Mondsee info invacare austria com Austria WWW www invacare at Ta Invacare n v T 32 0 50 83 10 10 L Autobaan 22 Fax 32 0 50 83 10 11 B 8210 Loppem Brugge belgium invacare com k 3 Belgium WWW www invacare be AL S Invacare AG T 41 0 61487 70 80 LH J BenkenstraRe 260 Fax 41 0 61487 70 81 7 CH 4108 Witterswil switzerland invacare com Switzerland WWW www invacare ch D Invacare Aquatec GmbH a 49 0 7562 70 00 t s Alemannenstrae 10 Fax 49 0 7562 7 00 66 88316 Isny info invacare aquatec com Deutschland WWW www invacare aquatec de pie Invacare A S T Kundeservice 45 0 36 90 00 00 DK Sdr Ringvej 37 Fax Kundeservice 45 0 36 90 00 01 j DK 2605 Br ndby denmark invacare com Danmark WWW www invacare dk CEJ Invacare SA T 34 0 972 49 32 00 t A c Areny
17. a vehicle using a ramp that exceeds the maximum safe slope Alternatively a tail lift installed in the vehicle may be used Only ever transfer the wheelchair to a vehicle with the backrest in an upright position Ensure that the total weight of the mobility aid including the user does not exceed the highest permissible weight for the platform lift Only ever run the wheelchair with the seat back in the upright position seat lifter lowered and the seat tilting in the upright position into the transport vehicle please refer to chapter Driving up and down gradients on page 31 Drive or push your wheelchair into the transport vehicle using a suitable ramp 87 12 2 Securing the wheelchair for transport without passengers amp CAUTION Injury hazard e Ifyou are unable to fasten your electric wheelchair securely in a transport vehicle we recommend that you do not transport it e Before transporting your wheelchair make sure the motors are engaged and that the Joystick Box is switched off e We urgently recommend securing the wheelchair to the floor of the transporting vehicle The wheelchair can be secured with straps at the following points Front Rear bumper Rear wheel Only the left hand side in each case is visible in the picture 88 13 Refurbishment The product is suitable for refurbishment Actions to be carried out e Cleaning and disinfection Please see chapter Care and maintenance on page 80
18. and used again and it happens to get wet during repair then it is easier to re fit it if you powder it lightly with talcum powder NOTE Re assembly is done in reverse order Make sure that the wheel is put back on the same side it was on and that it runs in the same direction it did before it was removed e Re fit the rim halves back into the tyre e Pump up the tyre a little e Insert the cylinder head screws in the rim and tighten to 10 Nm Make sure the inner tube does not get pinched between the rims halves e Check to make sure that the tyre is squarely in place on the rim e Pump up the tyre to the recommended tyre pressure e Check to make sure that the tyre is still squarely and snugly in place on the rim e Screw the valve cap back on e Refit the wheel e Refit the Torx screw using threadlock and tighten to 30 Nm 12 12 1 amp Transport Transferring the wheelchair to a vehicle WARNING Danger of tipping over if the wheelchair is transferred to a vehicle using a ramp that exceeds the maximum safe slope or if the backrest is not in an upright position during transfer If the wheelchair has to be transferred to a vehicle using a ramp that exceeds the maximum safe slope see chapter Technical specifications starting on page 91 then a winch must be used An attendant can then safely oversee and assist the transfer process If no winch is installed then the wheelchair must not be transferred to
19. ationary When parking your vehicle or if your vehicle is stationary for a prolonged period e Switch the vehicle s power system off ON OFF key e Activate your anti theft lock if existing Taking Obstacles Maximum obstacle height You can find information about maximum obstacle heights in the chapter entitled Technical specifications from page 91 Safety information when ascending obstacles CAUTION Danger of Tipping Over e Never approach obstacles at an angle but at 90 degrees as shown below e Put your backrest into an upright position before climbing an obstacle WARNING Danger of destruction of the front castor forks e Your wheelchair was designed for use as a piece of sports equipment and is therefore equipped with smaller front castors and lighter forks for better maneuverability which can be easily damaged if misused Never attempt to overcome obstacles such as kerbs with momentum but rather slowly and with the utmost caution 29 5 3 3 30 The correct way to overcome obstacles Ascending and descending The same approach applies to both ascending and descending obstacles e Approach the obstacle or the kerb slowly and at a right angle e Stop shortly before the front wheels come into contact with the obstacle e Check the position of the front wheels They must be in driving direction and at right angles to the obstacle e Approach slowly and keep at a consistent speed until the rear whee
20. ch individual case Pay attention to the Battery Charge Indicator Make sure to charge the batteries when the Battery Charge Indicator shows that battery charge is low We recommend charging the batteries after each trip as well as each night over night Depending on the level of discharge it can take up to 12 hours until the batteries are fully charged again Protect your charger from sources of heat such as heaters and direct sunlight If the battery charger overheats charging current will be reduced and the charging process delayed To avoid damaging the batteries never allow them to be fully discharged Do not drive on heavily discharged batteries if it is not absolutely necessary as this will strain the batteries unduly and shorten their life expectancy In case your vehicle is not used for a longer period of time then the batteries must be charged at least once a month to maintain a full charge Alternatively the vehicle can stay connected to the charger The batteries cannot be overcharged with the specified charger Please use only charging devices in Class 2 This class of chargers may be left unattended during charging All charging devices which are supplied by Invacare comply with these requirements 73 9 2 2 Charging the batteries A A 74 e Make sure you read and understand the battery charger s User s Manual if supplied as well as the safety notes on the front and rear panels of the charger WARNING Da
21. d successfully according to EN60529 IPX4 as to its resistance to spray water and is therefore well suited for typical middle European weather conditions When equipped with an appropriate lighting system the vehicle is suitable for use on public roads Under certain circumstances this vehicle can be used as a piece of sports equipment Make sure to comply with all safety information in section Safety information for using the wheelchair as a piece of sports equipment starting on page 19 Guarantee The terms and conditions of the guarantee are part of the general terms and conditions particular to the individual countries in which this product is sold 1 5 1 6 Indications The use of this mobility product is recommended for the following indications e The inability or a greatly restricted ability to walk within the scope of the basic requirement to be able to move within one s own four walls e The need to leave the dwelling place in order to get some fresh air during a short walk or to reach those places generally to be found at close distance to the dwelling and where everyday business is carried out e The use of the electric wheelchair for taking part in athletic activities after corresponding modifications Provision of electric wheelchairs for interior and exterior areas is advisable if the use of hand operated wheelchairs is no longer possible on account of the disability yet proper operation of an electromotive drive
22. edaceccusestacecederredersessecd Pushing the wheelchair in freewheel mode 6 1 Disengaging Motors K XK iK lidakkkakkkkk ak kaka aka kak k kk k kK KA KEKE KA KAKA KA KHE KA KAKA WA WA WA WA Remotes Adjusting the wheelchair to the user s seating posture 8 1 Adjusting the armrests and the control panel sssssssssssunssunnnrennnnnnnnnnnnnnnnnnnnnnnnnnn 8 1 1 Adapting the control panel to the length of the users arm 8 1 2 Setting the height of the remote llllldddddld klkkk kk kkkkkk kk ka 8 1 3 Setting the height of the arm reStS lllli iddddldlidk kk kk kk ek kk 8 1 4 Adjusting the width of the armrests Ll kk kk keke 8 2 Adjusting the seat angle seat heig tt U Eke ek 8 2 1 Manual adjustment using perforated plates LE ee 8 3 Adjusting the bDackrest cccccssssccecssseeeesseeeeeesseeeseeeseeseseseeseeeseaeseseseaeseeeseanseeeesaes 8 3 1 Adjusting the backrest manually L EEE kk kek 8 4 Adjusting the head rest cccccssscccssseneeseseeeseeesneeeeseseeeseeeseeeseeeeseaeseseseaeseseseaeseeeseaes 8 5 POStural Do lis s kulik nc end d da kk steve ceutste ceusuesteesuscevsdeesteseeusce eteeectedetencee 8 5 1 Types of postural beltS L kk kk kek k kk Ka KAKA RA 8 5 2 Adjusting the postural belt correctly Luii Eke e 8 6 L QMOSUS woe DDDr b rrTrTZZVlDDXogggoooo o Toeoeorrr rrrwwW
23. edges under the wheels 83 11 1 1 Repairing a flat tyre at the back tyre type 3 00 8 amp Injury hazard If the wheel has been insufficiently secured during assembly it can become loosened during driving When refitting the drive wheels tighten the Torx screw that secures the wheel to the hub to a torque of 30 Nm Secure all screws using a suitable threadlock e g Loctite 243 1 A Requirements Lr e e e Torque wrench with Allen bit 5 mm Torx bit T40 Repair kit for tyre repair or a new inner tube Talcum powder Threadlock Loctite e g Loctite 243 84 Removing the wheel e Jack the vehicle up and place a block of wood underneath it to prop it up e Remove the countersunk screw 1 using the Torx bit e Remove the wheel from the axle EXPLOSION HAZARD The wheel will explode if the air pressure is not released from the tyre before disassembling the wheel rim e Always make sure to completely release the air pressure by pressing the pin in the centre of the valve Repairing the flat tyre e Remove the valve cap e Letthe air out of the tyre completely by pressing the pin in the centre of the valve in e Remove the 5 cylinder head screws back of the wheel 2 e Remove the rim halves from the tyre e Remove the inner tube from the tyre e Repair the inner tube and re fit or replace it with a new one 86 NOTE In case the old inner tube is to be repaired
24. eelchair is also subjected to greater stress and wear An athlete must know and understand these risks A wheelchair user who would like to participate in a sporting event with his wheelchair should do so only after consulting a physician It is at the sole discretion of the physician to decide whether participation in a particular sport would be advisable or not Afterwards it is the responsibility of the wheelchair user himself to judge risks correctly and to act accordingly Invacare can not be held responsible in case of injury to the user or other persons and will provide no warranty in case of damage to the wheelchair which result from increased wear on account of it being used as a piece sports equipment 19 2 3 20 Safety information on electromagnetic interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference EMI Regulations However electromagnetic fields such as those generated by radio and television transmitters and cellular phones can influence the functions of electric vehicles Also the electronics used in our vehicles can generate a low level of electromagnetic interference which however will remain within the tolerance permitted by law For these reasons we ask you to please observe the following precautions WARNING Danger of malfunction due to electromagnetic interference Do not switch on or operate p
25. egrests Standard footrest with pre set angle Swivelling the footrest outward and or removing The small unlocking button is located on the upper section of the footrest When the footrest is unlocked it can be swivelled inward or outward when getting into the wheelchair as well as being removed completely 47 Press the unlocking button 1 and swivel the footrest outward Remove the footrest in an upward direction 8 6 1 2 Setting the angle amp PLEASE NOTE Danger of injury due to incorrect adjustment of the footrests and legrests e Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground yA Pre requisites ee 1x 6 mm Allen key 48 Loosen the screw 1 using the Allen key If the footrest cannot be moved after loosening the screw position a metal pin in the designated borehole 2 and use a hammer to knock on this lightly The clamping mechanism in the interior of the footrest will be released by this Repeat the procedure from the other side of the footrest if necessary Loosen the screw 1 using the Allen key Set the desired angle Re tighten the screw 49 8 6 1 3 Setting the end stop of the footrest M J Pre requisites E 1x 6 mm Allen key e 1x 10 mm open ended spanner The end position of the footrest is determined by means of a rubber stop 1 The rubber stop can be screwed in or out A or p
26. f batteries for lighting servos etc Measured without seat cushion The actual kerb weight depends on the fittings your mobility aid has been supplied with Every Invacare mobility aid is weighed when leaving the works Please refer to the nameplate for the kerb weight including batteries measured wees Static stability according to ISO 7176 1 9 15 8 Dynamic stability according to ISO 7176 2 6 10 5 93 16 94 Inspections Performed It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare Delivery Inspection 15 Annual Inspection Stamp of authorised Dealer Date Signature Stamp of authorised Dealer Date Signature 2 Annual Inspection 3 Annual Inspection Stamp of authorised Dealer Date Signature Stamp of authorised Dealer Date Signature 4 Annual Inspection 5 Annual Inspection Stamp of authorised Dealer Date Signature Stamp of authorised Dealer Date Signature 95 us 8uza OZ 0 LOZ 9 q 9Sg9 9 00Q 09196yFL IEeNUeN SIU JO ON 19p10 96
27. ferent requirements The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise Invacare or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users handicaps Some maintenance and settings can be performed by the user or his hers attendants Certain adjustments do however require technical training and may only be carried out by your Invacare specialist dealer Damages and errors caused by nonobservance of the operating manual or as a result of incorrect maintenance are excluded from all guarantees 10 This manual contains copyrighted information This manual may not be reproduced or reprinted either partly or completely without previous written consent from Invacare or its statutory representatives We reserve the right to make any necessary alterations on the grounds of technical improvements gt DP p De Important symbols in this manual General risks This symbol warns you of general hazards e Always follow the instructions to avoid injury to the user or damage to the product EXPLOSION HAZARD This symbol warns you of an explosion hazard which can be caused by excessive tyre pressure in a pneumatic tyre e Always follow the instructions to avoid injury to the user or damage to the product BURN HAZARD This symbol warns you of the danger of chemical burns f
28. her the castor wheels nor the ground e Loosen the locking knob 1 counter clockwise at least one turn 55 56 Hit the knob to release the locking mechanism Adjust the legrest to the desired angle 57 58 Tighten the knob clockwise 8 6 2 3 Setting the end stop of the legrest M J Pre requisites Ev e 1x 10 mm open ended spanner The end position of the legrest is determined by means of a rubber stop A The rubber stop can be screwed in or out A or pushed up or down B 59 60 Loosen the locking knob 1 counter clockwise at least one turn Hit the knob to release the locking mechanism 61 62 Swivel the legrest upward in order to access the rubber stop Use the open ended spanner to loosen the counternut 1 Move the rubber stop to the desired position Re tighten the counternut Move the legrest to the desired position Re tighten the locking knob 63 8 6 2 4 Adjusting the length of the legrest amp PLEASE NOTE Danger of injury due to incorrect adjustment of the footrests and legrests e Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground Mi Pre requisites ini e 1x6mm Allen key e Use the spanner to loosen the screw 1 e Adjust to the desired length e Re tighten the screw At 64 8 6 2 5 Adjusting the depth of the calf plate
29. icle This product has been supplied from an environmentally aware manufacturer This product may contain substances that could be harmful to the environment if disposed of in places landfills that are not appropriate according to legislation e The crossed out wheelie bin symbol is placed on this product to encourage you to recycle wherever possible e Please be environmentally responsible and recycle this product through your recycling facility at its end of life 13 1 3 1 4 14 Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired but who are still in terms of their eyesight and physically and mentally able to operate an electric vehicle It has been classified according to EN 12184 as a class B mobility product for indoor and outdoor areas It is therefore compact and agile enough for indoor areas but also able to overcome many obstacles in outdoor areas You can find exact information on speed turning radius range safe climbing ability maximum obstacle height and permissible operating conditions in chapter Technical specifications starting from page 91 Please also pay attention to all safety information in chapter Safety notes starting from page 16 The vehicle was successfully tested according to German and international standards as to its safety It satisfies the requirements according to DIN EN 12184 including EN 1021 1 2 It was also teste
30. ies which have been approved by Invacare for this mobility aid Key features 1 Sliding handle 2 Set screw for adjusting the height of the remote 3 Set screw for adjusting the angle of the backrest 4 Disengaging lever 5 Remote 6 Release button of the legrest 25 A 26 Getting in and out of the wheelchair Important information for getting into and out of the wheelchair from the side The armrest must be removed in order to get into or out of the wheelchair from the side Remove the standard armrest in order to side transfer Removing the armrest e Disengage the release handle 1 e Pull the side part out of its holder Getting into the wheelchair Position your wheelchair as close as possible to your seat This might have to be done by an attendant Switch your wheelchair off Apply the manual wheel lock of your wheelchair if existing Detach the skirt guard of your wheelchair or swivel it up Now slide into the wheelchair Getting out of the wheelchair Drive your wheelchair as close as possible to your seat Switch your wheelchair off Apply the manual wheel lock of your wheelchair if existing Detach the skirt guard of your wheelchair or swivel it up Now slide onto your new seat NOTE If you do not have sufficient muscle strength you should ask other persons for help Use a sliding board if possible 27 ol 5 1 28 Driving NOTE The maximu
31. ilable from the Robert Koch Institute at http www rki de 10 1 Safety checks that should be performed by the user Explanation of the symbols n During normal use as well as during use as a piece of sports equipment Especially during use as a piece of sports equipment Maintenance Jobs g oO 2 lgi 2 2 385 8 amp F 5 8 a Seat and backrest padding Check for perfect condition of Side part and armrest Are all fastening elements correctly tightened ff Can armrests side parts be removed and installed without too much of physical effort Are armrests secured in their positions af Legrests Do legrests lock into place without any problem only applies to u detachable legrests Do the different adjustment functions work without any problem Tyres Have tyres checked for specified air pressure 2 5 bar 81 82 Maintenance Jobs 4 o Sos 2 3 2 885 F 2 3 z a Front wheel forks Front wheels Front wheels must be running smoothly l of Check fork bearing for firm seat torque 15 Nm 1 5 Nm ff Rear wheels Test wheel for firm seat on the axle drive shaft if Rear wheels must turn without wobbling l Electronics Electrical System Check all plug connections for condition and firm seat u Fully cha
32. ion then your wheelchair needs to be equipped with an appropriate lighting system Please contact your Invacare dealer if you have any questions Pushing the wheelchair in freewheel mode The motors of the wheelchair are equipped with automatic brakes preventing that the wheelchair starts rolling out of control when the joystick box is switched off When pushing the wheelchair manually whilst freewheeling the magnetic brakes must be disengaged Disengaging Motors Danger of the vehicle running away e When the motors are disengaged for push operation whilst freewheeling the electromagnetic motor brakes are deactivated When the vehicle is parked the levers for engaging and disengaging the motors must without fail be locked firmly into the DRIVE position electromagnetic motor brakes activated NOTE The motors may only be disengaged by an attendant not by the user This ensures that the motors are only disengaged if an attendant is available to secure the wheelchair and prevent unintended rolling The lever for disengaging the motors is on the rear right side on the wheelchair chassis Declutching the motors e Switch off the remote e Pull the locking pin 1 on the underside of the declutching mechanism not visible in the picture Pull the coupling lever to the rear 2 The motors are declutched Reclutching the motors e Push the coupling lever 2 to the front The motors are reclutched Remotes
33. k kk k KA 72 9 2 2 Charging the batteries lt csecbe heviaz g0gngxgggo A 74 9 2 3 Removing and fitting batteries ee 40 54i4434082ai y yd EERTE ERTA 76 9 2 3 1 Removing the batteries ariora nE R RE TEETAN ney ter ARK KRA KARAN 77 9 2 3 2 How to handle damaged batteries correctly iiuii kek 79 Care and maintenance 80 10 1 Safety checks that should be performed by the US r ssssssussennunnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 81 Repair Instructions 83 111 Repairing a flat tyne eoi ea a R a A k lt kre kar e R A A A EN 83 11 1 1 Repairing a flat tyre at the back tyre type 3 00 8 l b L uuu iie 84 Transport 87 12 1 Transferring the wheelchair to a ve hicle ll lillllll kak kak kaka kak kk kk kk kk KA 87 12 2 Securing the wheelchair for transport without passengers s ssssssssennnnrennnnnrnnnnnnnnnnnnnnn 88 Refurbishment 89 14 Disposal 15 Technical specifications 16 Inspections Performed 90 91 94 Introduction Dear user First we would like to thank you for purchasing our product We hope that you will have a great deal of pleasure with your new power wheelchair This operating manual contains important information and notes about e Safety e Operation Care and maintenance Please take care to read the operating manual thoroughly before starting out on your first journey This wheelchair has been constructed for a large circle of users with dif
34. ls have also passed over the obstacle 5 4 Driving up and down gradients For information concerning the maximum safe slope please see chapter Technical specifications starting on page 91 amp WARNING Danger of tipping over e Only ever drive downhill at a maximum of 2 3 of the top speed Avoid sudden changes of direction or abrupt braking when driving on slopes e Always return the backrest of your seat or the seat tilt if adjustable seat tilt is available to an upright position before ascending slopes We recommend that you position the seat backrest or the seat tilt slightly to the rear before descending slopes e Always lower the lifter if fitted to its lowest position before ascending or descending a slope e Never attempt to ascend or descend a slope on slippery surfaces or where there is a danger of skidding such as wet pavement ice etc e Avoid trying to get out of the vehicle on an incline or a gradient e Always drive straight in the direction the road or path you are on goes rather than attempting to zigzag e Never attempt to turn around on an incline or a slope amp Braking distance is much longer on a downhill slope than on even terrain e Never drive down a slope that exceeds the maximum safe slope see chapter Technical specifications on page 91 31 5 5 32 Use on public roads If you wish to use your wheelchair on public roads and lighting is required by national legislat
35. m load capacity that is stated in the technical data only states that the system is designed for this mass in total However this does not mean that one can sit a person with this body weight in the wheelchair without restrictions Attention must be paid to the body proportions such as height weight distribution abdominal girth leg and calf girth and seat depth These factors have a strong influence on driving features such as tilt stability and traction The permissible axle loads in particular must be adhered to see chapter Technical specifications as from page 91 It may possibly be necessary to carry out adaptations to the seat system Before driving for the first time Before you take your first trip you should familiarise yourself well with the operation of the vehicle and with all operating elements Take your time to test all functions and driving modes NOTE If installed make sure to properly adjust and use the postural belt each time you use the wheelchair Sitting Comfortably Driving Safely Before each trip make sure that e You are within easy reach of all operating controls e The battery charge is sufficient for the distance intended to be covered e The postural belt if installed is in perfect order 5 2 5 3 5 3 1 5 3 2 amp A e The rear mirror if installed is adjusted so you can look behind at all times without having to bend forward or shift your seating position Parking and st
36. nger of explosion and destruction of batteries if the wrong battery charger is used e Only ever use the battery charger supplied with your vehicle or a charger that has been approved by Invacare Danger of electric shock and damage to the battery charger if it is allowed to get wet e Protect the battery charger from water e Always charge in a dry environment Danger of short circuit and electric shock if the battery charger has been damaged e Do not use the battery charger if it has been dropped or damaged Danger of fire and electric shock if a damaged extension cable is used e Only ever use an extension cable if it is absolutely necessary In case you must use one make sure it is in good condition Charging the batteries Switch off the wheelchair at the Joystick Box Connect the battery charger to the Joystick Box the charging socket is located on the bottom of the Joystick Box 1 Connect battery charger to the mains outlet and switch on if necessary After charging is complete first disconnect the battery charger from the mains supply then disconnect from the Joystick Box 75 9 2 3 oP 76 Removing and fitting batteries WARNING Danger of injury if the batteries are not handled correctly during assembly and maintenance work e New batteries should be installed by authorised technicians e Observe the warnings on the batteries e Take into account the heavy weight of the batteries e
37. or example due to the discharge of battery acids e Always follow the instructions to avoid injury to the user or damage to the product BURN Risk This symbol warns of the risk of burns for example as a result of hot motor surfaces e Follow the instructions in order to avoid injury or damage to the product RISK OF CRUSHING This symbol warns of a risk of crushing caused by being careless with heavy components e Always follow the instructions to avoid injury to the user or damage to the product 11 Ve 12 Wear eye protection This symbol refers to the requirement for wearing eye protection for example when working with batteries e You must wear safety goggles when this symbol is displayed Wear protective gloves This symbol indicates the requirement to wear protective gloves for example when working with batteries You must wear protective gloves when this symbol is displayed NOTE This symbol identifies general information which is intended to simplify working with your product and which refers to special functions Requirements e This symbol identifies a list of various tools components and items which you will need in order to carry out certain work Please do not attempt to carry out the work if you do not have the listed tools available READ WELL BEFORE OPERATION This symbol advises you to read information carefully 1 2 Important symbols found on the veh
38. ortable transceivers or communication devices such as radio transceivers or cellular phones when the vehicle is switched on Avoid getting near strong radio and television transmitters In case the vehicle should be set in motion unintentionally or the brakes are released switch it off immediately Adding electrical accessories and other components or modifying the vehicle in any way can make it susceptible to electromagnetic interference Keep in mind that there is no sure way to determine the effect such modifications will have on the overall immunity of the electronic system Report all occurrences of unintentional movement of the vehicle or release of the electric brakes to the manufacturer Safety information on driving and freewheel mode Danger of injury if the wheelchair tips over Inclines and declines can only be travelled up to the maximum safe slope see chapter Technical specifications from page 91 Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes We recommend that you position the seat backrest and the seat tilt if fitted slightly to the rear before descending slopes Only ever drive downhill at a maximum of 2 3 of the top speed Avoid abrupt braking or accelerating on gradients If at all possible avoid driving on slippery surfaces such as snow gravel ice etc where there is a danger of you losing control over the vehicle especially on a gradient
39. r r nr 2 Safety notes 2 1 General safety Notes jvciiidcicsicced cevetedeecseneductescued eesti shgeecad duetecteabesseusdueeectedveeseciectesscnd 2 2 Safety information for using the wheelchair as a piece of sports equipment 2 3 Safety information on electromagnetic interference cccceesseeeeseeeeeeseeneeeeseees 2 4 Safety information on driving and freewheel MOdEC ccseecceceesereeeeeeeeseeeseeneeeeeeees 2 5 Safety information regarding changes and modifications to the mobility device 3 Key features 4 Getting in and out of the wheelchair 4 1 Remove the standard armrest in order to side transfer 5 Driving 5 1 Before driving for the first tirme c ccccceseeseeseseeeeeeeeeeeeeeeeeneeseseeeeesesesneesesesnenseeeseenees 5 2 Parking and Stationary oc cesicceccesctectevseeeeeceseaceecesceeedevsceeeteusuceedessodeesusueeesdevsuceeses suas 5 3 Taking Obstacles eect iil yk inyay este k ak kek kesa kun dek ka Ku i hk k ne n ku a x ra kiwa k 5 3 1 Maximum obstacle helghtt ul lk ka kak ee akA kak wA AA KRA 5 3 2 Safety information when ascending Obstacles ccceeceeeeeeeseeeeeeenteeeeees 5 3 3 The correct way to overcome obstaclesS EEiiui EEE e 5 4 Driving UP and down Gradients ecesccceeseeeeeeeseneeeeeeeeeeeeeseeneeeeseeneeeaseeeeeenseeeeeenees 5 5 Use On PUBIC OAS saa ass Wan WE W ban ZAVA sted cececedeseedec
40. re you get in get out or handle unwieldy objects e When the drive is disengaged the brake inside the drive is deactivated For this reason pushing the mobility device by an attendant is only recommended on flat surfaces never on gradients Never leave your mobility device on a gradient with its motors disengaged Always re engage the motors immediately after pushing the mobility device see chapter Pushing the wheelchair in freewheel mode on page 32 Danger of injury if the mobility device is switched off while driving for example by pressing the On Off Button or disconnecting a cable due to it coming to an abrupt sharp stop e Ifyou have to brake in an emergency simply release the joystick which will bring you to a halt refer to the joystick operating manual for more information Danger of injury when transferring mobility device to a vehicle for transport with the occupant seated in it e Itis always better to transfer the mobility device to a vehicle without the occupant seated in it e Ifthe mobility device needs to be loaded up a ramp together with its driver ensure that the ramp does not exceed the maximum safe slope see chapter Technical specifications from page 91 e Ifthe mobility device does need to be loaded using a ramp which exceeds the maximum safe slope see chapter Technical specifications from page 91 then you must use a winch An attendant can safely monitor and assist the loading process e
41. replaced only after checking the entire electric system An Invacare specialised dealer must perform the replacement You can find information on the fuse type in chapter Technical specifications starting on page 91 The entire electric system of the wheelchair is protected by the main fuse against overloading The main fuse is to be found underneath the battery cover 1 71 9 2 9 2 1 72 Batteries What you need to know about batteries Power is supplied by two 12 V batteries The batteries are maintenance free and only need regular charging New batteries should always be fully charged once before their first use New batteries will be at their full capacity after having run through approx 10 20 charging cycles How fast the batteries discharge depends on many circumstances such as ambient temperature condition of the surface of the road tyre pressure weight of the driver way of driving and utilisation of lighting NOTE The batteries supplied with your electric vehicle are not hazardous goods This classification is based on the German GGVS Hazardous Goods Road Transport Ordinances and the IATA DGR Hazardous Goods Rail Transport Air Transport Ordinances Batteries may be transported without restrictions whether by road rail or by air Individual transport companies have however guidelines which can possibly restrict or forbid certain transport procedures Please ask the transport company regarding ea
42. ressure e 2 8 bar Tyre type e Castor wheel tyres 200x50 puncture proof 92 Driving features Speed 10 km h Min braking distance 2100 mm Max safe slope 10 18 according to manufacturer s specifications with 120 kg payload 4 seat angle 20 backrest angle Max climbable obstacle height 60 mm Turning diameter 830 mm Range according to ISO 7176 4 2008 approximately 45 km Seat width adjustable range of the armrests in brackets Total height e 950mm Total width e 630mm Overall length incl std footrests e 1100 mm Total length excl legrests e 880 mm Seat height e 455 530 mm LU 430 mm 440 490 mm Seat depth e 410 460 510 mm Height of backrest e 480 540 mm Seat cushion thickness e 50mm Backrest angle e 10 0 7 5 15 22 5 30 Height of armrest e 290 360 mm Footrest length e 330 340 350 360 380 390 420 mm Seat tilt manual adjustment e upto 22 Kerb weight 115 kg Loading Max load e 120 kg Approximately Width adjustable for side panel adjustment Note The drive range of an electric wheelchair is strongly influenced by external factors such as the charging state of the batteries surrounding temperature local topography road surface characteristics tyre pressure weight of user drive style and use o
43. rge the batteries before daily use Before every trip Are all holders screws firmly fixed tight and safe of Are all electric bulbs of the lighting system if applicable in working order Before every trip Cleaning Clean all parts carefully When necessary Once a year you should have your wheelchair inspected and serviced by your authorised dealer if it is used as a piece of sport equipment then it should be inspected twice a year If the wheelchair is serviced at regular intervals damaged or worn parts can be located and replaced in time thus preserving it in good working order A complete checklist of necessary maintenance work can be found in the Service Manual which can be obtained from Invacare 11 Repair Instructions The following are instructions on repairs that can be performed by the user For the specifications of spare parts please see Technical specifications on page 91 or consult the Service Manual available from Invacare in this connection please see the addresses and phone numbers in section How can you get in touch with Invacare on page 2 In case you require assistance please contact your Invacare Dealer Repairing a flat tyre WARNING Danger of damage or injury if the vehicle is accidentally set into motion during repairs e Switch the power off ON OFF Button e Engage the motors Secure the vehicle against rolling away by placing w
44. roperly locked into place Danger of injury if you collide with an obstacle when driving through narrow passages such as doorways and entrances e Drive through narrow passages in the lowest driving mode and with due caution If your power wheelchair has been fitted with angle adjustable legrests there is a danger of personal injury and damage to the wheelchair if you drive the wheelchair with the legrests raised e To avoid unwanted displacement of the wheelchair centre of gravity to the front especially when travelling downhill and in order to avoid damage to the wheelchair angle adjustable legrests must always be lowered during normal travelling CAUTION Danger of tipping Anti tip wheels stabilisers are only effective on firm ground They sink in on soft ground such as grass snow or mud if the electrical vehicle rests itself on them They lose their effect and the electrical vehicle can tip over e Only drive with extreme care on soft ground especially during uphill and downhill journeys In the process pay increased attention to the tip stability of the electric vehicle 2 5 Safety information regarding changes and modifications to the mobility device CE marking of the wheelchair The conformity assessment CE marking was carried out in accordance with Directive 93 42 EEC MPG Medical Devices Act and only applies to the complete product The CE marking is invalidated if components or accessories are replaced
45. side which can result in the buckle not sitting centrally 45 46 Belt with metal buckle adjustable both sides Belt can be adjusted on both sides This means that the buckle can be centrally positioned Harness with metal buckle adjustable on both sides Harness can be adjusted on both sides This ensures that the buckle is always centrally positioned 8 5 2 8 6 8 6 1 8 6 1 1 Adjusting the postural belt correctly Ensure that you are sitting correctly which means that you are sitting right at the back of the seat your pelvis is positioned erect and as symmetrically as possible not to the front to the side or at one edge of the seat Position the postural belt so that your hipbones can be easily felt above the belt Adjust the belt length using one of the adjustment aids described above The belt should be adjusted so that you can fit a flat hand between the belt and your body The buckle should be positioned as centrally as possible In doing so please carry out adjustments on both sides as much as possible Please check your belt every week to ensure that it is still in good working condition to ensure it has no damage or wear and that it is fixed properly to the wheelchair If the belt is only fastened with a bolted connection ensure that the connection has not loosened or undone You can find more information about maintenance work on belts in the service manual which is available from Invacare L
46. unit is still practicable Life expectancy We estimate a life expectancy of five years for this product provided it is used in strict accordance with the intended use as set out in this document and all maintenance and service requirements are met The estimated life expectancy can be exceeded if the product is carefully used and properly maintained and provided technical and scientific advances do not result in technical limitations The life expectancy can also be considerably reduced by extreme or incorrect usage The fact that we estimate a life expectancy for this product does not constitute an additional warranty 15 N 16 Safety notes READ WELL BEFORE OPERATION General safety notes Danger of injury if mobility device is used in any other way than the purpose described in this manual e Only ever use the mobility device in accordance with the instructions in this User s Manual see chapter Type classification and permissible use on page 14 e Pay strict attention to the safety information Danger of injury if the mobility device is driven when ability to operate a vehicle is impaired by medication or alcohol e Never drive the mobility device under the influence of medication or alcohol If necessary the mobility device must be operated by an attendant who is physically and mentally able Danger of damage or injury if mobility device is accidentally set into motion e Switch the mobility device off befo
47. ushed up or down B 50 Use the Allen key to loosen the screw 1 and swivel the footrest upward in order to access the rubber stop Use the open ended spanner to loosen the counternut 1 51 52 Move the rubber stop to the desired position Re tighten the counternut Move the footrest to the desired position Re tighten the screw 8 6 1 4 f Adjusting the length of the footrest PLEASE NOTE Danger of injury due to incorrect adjustment of the footrests and legrests e Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground Pre requisites e 1x5mm Allen key e Use the spanner to loosen the screw 1 e Adjust to the desired length e Re tighten the screw At 53 8 6 2 Manually height adjustable legrest 90 0 8 6 2 1 Swivelling the legrest outward and or removing The small unlocking button is located on the upper section of the legrest When the legrest is unlocked it can be swivelled inward or outward when getting into wheelchair as well as being removed completely e Press the unlocking button 1 and swivel the legrest outward e Remove the legrest in an upward direction 54 8 6 2 2 Setting the angle A PLEASE NOTE Danger of injury due to incorrect adjustment of the footrests and legrests e Before and during every journey it is imperative to ensure that the legrests contact neit
48. y device like wheels or one of the Lifter Modules if fitted especially when children are around Risk of injury from hot surfaces e Do not leave the wheelchair in direct sunlight for prolonged periods Metal parts and surfaces such as the seat and armrests can become very hot Danger of fire or breaking down due to electric devices being connected e Do not connect any electric devices to your mobility device that are not expressly certified by Invacare for this purpose Have all electrical installations done by your authorised Invacare Dealer 2 2 Safety information for using the wheelchair as a piece of sports equipment SAFETY INFORMATION ON THE USE OF THE WHEELCHAIR AS A PIECE OF SPORTS EQUIPMENT PLEASE MAKE SURE TO READ FIRST The following chapter contains safety information which is meant to ensure the safe use of the wheelchair in everyday situations The safety of the user but also of other persons who might be in the vicinity of wheelchair is the main focus of this information Therefore it is of the utmost importance to follow these instructions When using the wheelchair as a piece of sports equipment the situation can be slightly different In this situation also the safety of bystanders and spectators should be of primary importance to the organizers of the sporting event and the participating athletes At the same time the athletes knowingly expose themselves to an increased risk of injury and the wh
Download Pdf Manuals
Related Search