RollOn Instruction Guide 182241 Rev 01 EN - Hill-Rom
Contents
1. Tighten the locking handle Helpful hint The above adjustments can be aided by lifting the front edge of the support handle frame and pressing it in against the mast while at the same time moving it up or down Safety lock functions To open the seat frame Slide the red safety lock aside and turn the guide handles upwards It is easier to open the seat frame if the patient while standing in the RollOn leans for ward against the torso cushion To lock the seat frame Turn the guide handles downwards Slide the red safety lock sideways to the locked position A IMPORTANT Ensure that the safety lock is in the locked position before beginning the transfer Base width adjustment The base is widened by loosening the locking handles and manually pulling the two sides outwards If desired tighten the locking handles RollOn can however be easier to use if the locking handles remain unlocked RollOn has enough stability in all width settings Locking the wheels To lock the wheels With your foot press down the red locking pedal The wheels are locked in all directions To release wheel lock Flip the red locking pedal up A During raising the wheels should be locked to prevent the RollOn from moving RollOn 182241 Rev 01 7 www liko com Trial Fitting A Hip joint P Measurement scales The RollOn has two different measurement scales for the raising handle seat frame2. and the lower leg support The measurement scales are calibrated from 1 to 10 where 1 indicates the lowest setting and 10 the highest setting The measurement scales are intended to be used with respect to the patient s height The correct set ting can be different for two individuals with the same height Guidelines for appropriate settings are as follows Position 1 patient height from about 140 cm 55 inch and taller Position 5 patient height from about 175 cm 69 inch and taller Position 10 tall patients up to about 205 cm 81 inch NOTE These guidelines are based on average values Deviations can and do occur Correct individual adjustment may imply different numerical settings positions for the raising handle seat frame and lower leg support depending on the patient s individual conditions IMPORTANT An individual trial fitting is neces sary to achieve a correct and safe setting for each individual patient Helpful hint To facilitate use of the RollOn with se veral patients simply record the results of trial fitting with each patient By referring to these notes you can make the appropriate settings quickly and easily whenever the need to use the raising support arises C N RollOn 182241 Rev 01 Raising handle seat frame The raising handle facilitates several different gras ping alternatives for the patient during raising The seat frame functions as a support for the pa
3. assembled mast over the foot on the base Ensure that the foot of the mast is flush against the base Make sure the wheels are locked before installing the mast on the base www liko com 2 Pi 7 Secure the mast to the base with the accom 8 Replace the torso cushion on the mast Secure panying locking screws 4 pcs into the threaded the torso cushion with the locking screws that were holes on each side of the mast Tighten the locking removed in step 1 screws with the Allen key included g gt O Ns wf 9 Press the plastic foot plate back in place on the 10 Place the Quick Reference Guide in the intended frame holder on the mast After assembly check the following e that the mast is firmly secured to the base e that the raising handle seat frame and lower leg support are set at the appropriate positions on the mast and the locking handles are tightened e wheel brake functions e locking handles function e safety lock functions RollOn 182241 Rev 01 6 www liko com Operation Adjustment of lower leg support The height and depth of the lower leg support are adjustable Loosen the locking handles and make the appropriate adjust ments Tighten the locking handles Adjustment of the raising handle seat frame The height of the raising handle seat frame can be adjusted Loosen the locking handle and make the appropriate adjust ment
4. handle for base width i adjustment 42 i 6 Foot plate 7 Front wheels 11 pi 4 8 Base N 9 Rear wheel with brake 107 5 10 Locking handle for lower leg 4 support 11 Holder for Instructions for Use 12 Mast 9 N gt 13 Guide handles i Bw 14 Safety lock Ce 15 Seat frame o 16 Torso cushion RollOn 182241 Rev 01 3 www liko com Technical Specifications Wheels Front 75 mm twin wheels Material Aluminium Rear 75 mm brake equipped twin wheels Measurements G Max B Ge D E a J K Weight Turning RollOn bad Max Min Max Min Max Min Max Min F S 4 Max Min Max Min b total diameter A 160 141 115 99 111 95 60 46 27 24 92 11 26 89 90 62 78 49 63 25 105 B 350 56 45 39 44 37 22 18 1 9 136 411 35 35 24 31 19 25 55 41 A Max load and weight in kg Measurements in cm B Max load and weight in Ibs Measurements in inch Max and min values values within the measurement scales areas Floor clearance without load RollOn 182241 Rev 01 4 www liko com Assembly Instructions e Base with frame for foot plate e Plastic foot plate e Mast with torso cushion e Raising handle seat frame with rear supports incl anti friction plate Before assembling make sure you have
5. is periodically unable to participate in a transfer with the support for raising we recommend the use of the powered sit to stand lift Sabina A Caution triangles are used to warn of situations that demand extra care and attention In this document the person being transferred is referred to as the patient and the person helping them is referred to as the caregiver Cli IMPORTANT Transferring a patient always involves a degree of risk A complete understanding of the contents of instructions is essential and only trained personnel should use the equipment When in doubt contact Liko Hill Rom Contents Safety INStrUCHONS i s2sccicesctetetteces T eee siete 3 DC TIMINONS e O i E caleba belt uated Gabe E E 3 Technical Specifications cccccccceeeececececeecaeeeeeeeeeeeeetecececaesaeeeeeeeeeeeteeeees 4 MGASUFEMOMS sereine naaa 4 Assembly INStrUCHONS sepisan E nantes made 5 PST ATOMS asoini aaar e a aa iaaa N a aAa hai aa ROA TAAA 7 Tial RUN epena aAA A epee eee ty 8 Work the Right Way with RollONn assesses cirirrssiciserieiadiiiaiie aii Transfer Between Bed and Chair wheelchair c ceeeeeeeceeeeeeeteeeeeenaes 9 Transfer from Chair wheelchair to Toilet neeeeeeeeeeeeeeereeeerrrereeensnne 10 Repositioning Further Back in the Chair wheelchaiir ccceeeeeees 11 Problems During USC osiinsa inn neinna N ENEE 11 Inspection and Maintenance esner rnnr 12 A NOTE This instruction guid
6. the following components and tools e Lower leg support incl anti friction plate e Locking screws for mast 4 pcs e Allen keys for locking screws 4 mm and 5 mm e Quick Reference Guide Before assembling remove the red tape that holds the anti friction plates for the lower leg support and raising handle seat frame 1 Dismount the locking screws 2 pcs under the torso cushion Remove the torso cushion 2 Ensure that an anti friction plate A has been affixed to the protruding part of the raising handle seat frame mount 3 Lay down the raising handle seat frame with the rear Support and guide handles facing down Turn the mast upside down Insert the mast in the raising handle seat frame mount Secure the raising handle seat frame in place with the locking handle 4 Lay down the mast with the raising handle seat frame Ensure that an anti friction plate has been affixed to the protruding part of the mount see A in step 2 Turn the mount so that the locking handle for the lower leg support s height adjustment B is facing upwards see inset illustration Insert the lower leg support into the front track on the mast Secure the lower leg support in place with the lock ing handle B 3 N i J 5 Lock the rear wheels on the base Remove the plastic foot plate from the frame RollOn 182241 Rev 01 6 Place the completely
7. 4 Liko A cD Company RollOn Instruction Guide English 182241 Rev 01 2013 06 24 A Applies to the following models RollOn Prod No 6001001 Product Description RollOn support for raising is a manual assistive device developed for safe transfers to and from the sitting position The RollOn is intended for patients who have considerable difficulty walking but have good arm strength and the necessary leg strength to support their full weight The RollOn bridges the gap between conventional walkers and powered sit to stand lifts The RollOn is a reliable aid during raising and it facilitates transfers for example between bed chair wheelchair and toilet A patient who has slid forward in a chair can easily be repositioned more comfortably further back in the chair The RollOn is adjusted to meet the needs of the individual patient With a correctly adjusted seat frame and lower leg support the patient is assured of secure support that will enable them to stand safely and with good stability The raising handle facilitates several different gras ping alternatives for the patient during raising The base is easily adjusted for different wheelchairs and beds The torso cushion helps to support the body during dressing and undressing e g in connection with visits to the toilet The rear supports support the patient during transfers and are not intended for the patient to sit on If the patient
8. asier if the patient leans forward against the torso cushion Secure the seat frame with the safety lock RollOn 182241 Rev 01 4 Check that the settings for the seat frame are correct Unlock the wheels A Important Ensure that the safety lock is in the locked position before beginning the transfer gt www liko com e A 5 Ensure that the patient is standing securely 6 Place the RollOn in front of the chair wheelchair in the RollOn Transfer the patient to the desired It may sometimes be necessary to widen the base location in order to gain better access to where the patient will be sitting e g to get around a wide chair wheelchair Lock the wheels Move the safety lock aside and turn the seat frame up This is easier if the patient leans forward against the torso cushion 7 Let the patient grasp the raising handle and 8 Unlock the wheels Remove the patient s feet lean forward at the same time as he she sits from the foot plate and roll the RollOn out of the down way Transfer from Chair wheelchair to Toilet In some cases for transfers to and from the toilet the assistance of a second caregiver may be reassuring In such cases it is best if one caregiver stands in front of the patient and stabilizes the RollOn by holding the guide handles while the other caregiver assists with dressing and undressing 7 a 1 Raising and transfer are performed as 2 P
9. e contains important information about the use of the product All personnel who use this product must be thoroughly familiar with the contents of this instruction guide Remember to keep the instructions where they are easily accessible for users of the product RollOn 182241 Rev 01 2 www liko com Safety Instructions Before using the product make certain that e you have read the instructions e the support for raising is assembled according to the assembly instructions e personnel using the support have received appropriate instructions and training e the raising handle seat frame are properly secured with the locking handle e the proper adjustments have been made see page 7 8 e the patient is able to stand securely in the support before the transfer takes place Remember e The need for one or more caregivers must be determined from case to case e As a caregiver you are responsible for the patient s safety You must be well informed of the patient s condition and ability to manage the transfer situation with RollOn e Never leave a patient unattended during a transfer situation CE RollOn complies with the requirements of the directive for Class 1 medical technical products MDD 93 42 EEC Max load 160 kg 350 Ibs Definitions a N 1 ye 16 1 Locking handle for raising handle 4 7 seat frame J NS 2 Raising handle 44 2 3 Rear supports 4 Lower leg support 13 i 3 5 Locking
10. iko a CED company w liko com Manufacturer Liko AB Nedre v gen 100 SE 975 92 Lule Sweden info liko se Copyright Liko AB 2013 06
11. lace the RollOn in front of the toilet If neces described earlier in points 1 through 6 Ensure sary widen the base to enable the patient to get that the patient is standing securely in the as close as possible to the toilet Lock the wheels RollOn before starting the transfer Turn the seat frame up this gives plenty of space to assist the patient with clothing If necessary the patient can support himself herself against the torso cushion RollOn 182241 Rev 01 10 www liko com Repositioning Further Back in the Chair wheelchair Repositioning the patient further back in the chair wheelchair is easier if the wheels on the RollOn are not locked since the patient can be positioned further back in the chair when he she is standing in the RollOn 1 The RollOn is ideal for repositioning a patient who has slipped too far down in the chair to a more comfortable position further back A Make sure that the wheels on the wheelchair are locked 3 When the patient is sitting comfortably in the chair remove his her feet from the foot plate and roll the RollOn out of the way 2 Place the RollOn in front of the chair If neces sary the base can be widened Place the patient s feet in the centre of the foot plate Let the patient grasp the raising handle and pull himself herself up free of the chair or to a standing position Move the RollOn with the patient as close to the seat as possible The patien
12. pection repair and maintenance should be performed only in accordance with the Liko Service Manual and by personnel authorized by Liko Hill Rom and using original Liko spare parts Service Agreement Liko Hill Rom offers the opportunity to enter into service contracts for the maintenance and regular inspection of your Liko Hill Rom product Expected Life Time The product has an expected life time of 10 years when correctly handled serviced and inspected in accordance with Liko s instructions Transport and Storage During transport or if the lift is not going to be used for a long time the emergency stops should be engaged The environment in which the lift is transported and stored should have a temperature of 10 40 C 50 104 F and a relative humidity of 30 75 The air pressure should be 700 1060 hPa Recycling For instructions on how to recycle your Liko product please visit our website www liko com Product Changes Liko s products undergo continuous development which is why we reserve the right to make product changes without prior notice Contact your Liko Hill Rom representative for advice and information about product upgrades Design and Quality by Liko in Sweden Hill Rom s Management system are certified in accordance with ISO 9001 and its equivalent for the medical de vice industry ISO 13485 Hill Rom s Management system is also certified in accordance with environmental stan dard ISO 14001 A L
13. t can now sit comfortably further back in the chair Problems During Use If the patient does not achieve a sufficiently upright position the rear supports cannot be lowered The patient s physical status e g generally weak musculature low tonus and or contractures in the knees and hip joints may prevent him her from achieving a sufficiently upright position which means that the rear supports cannot be lowered behind the patient In such cases the RollOn should not be used Instead we recommend the use of a lift from Liko s product range the first choice being the sit to stand lift Sabina which can be used for lifting to the standing position and transfers to chair wheelchair or toilet RollOn 182241 Rev 01 www liko com Inspection and Maintenance Care and Maintenance To ensure trouble free operation certain components should be checked each day the RollOn is used e Check the RollOn for any signs of external damage e Check raising handle seat frame and lower leg support function e Check safety lock function When necessary clean RollOn with a moist cloth and check that the wheels are free from dirt Find more detailed information regarding cleaning and disinfection of your Liko Hill Rom product in the document Care and Maintenance at our website www liko com A RollOn should not be exposed to running water Service A periodic inspection of RollOn should be carried out at least once per year Periodic ins
14. tient and the rear supports provide comfortable support for the buttocks but the frame can also be used as a guide handle by the caregiver The rear supports can be raised and lowered more easily if the patient leans forward against the torso cushion Helpful hint Use the seat frame as a guide to set the correct height To prevent the patient from sitting on the rear supports and to prevent him her from sliding down and out of the support the frame should be set just under the patient s hip joints see illustration above A Caution If the rear supports are too low the patient may tend to sit on them The rear supports are not intended to support this weight If the rear supports are positioned too high there is a risk that the patient might slide down out of the support Lower leg support Place the patient s feet in the centre of the foot plate The lower legs must be parallel with the lower leg support Adjust the height of the lower leg support so that it provides comfortable counter pressure just beneath the patient s kneecaps If needed the lower leg support can also be vertically adjusted After adjusting tighten the locking handles www liko com Work the Right Way with RollOn Be careful with your back Remember to work ergonomically correct with the RollOn Do not lift manually Let the patient and the upright support do the job Take it easy Work calmly and methodically Don t strain yo
15. ur back Work in a walking stance with your back straight Walk as you roll the support Reduce the lever effect Work close to the patient and the support Transfer Between Bed and Chair wheelchair The procedure for transferring from bed to chair wheelchair is described below When transferring from chair wheelchair to bed the procedure is reversed Before the transfer can begin it is important to ensure that the lower leg support and raising handle seat frame are correctly adjusted according to the needs and condition of the patient Also check that the support and handle frame are properly secured with the locking handles r Ag nS A 1 Place the RollOn in front of and close to the patient Lock the wheels Place the patient s feet in the centre of the foot plate with the lower legs parallel to the lower leg support Let the patient grasp the raising handle It is easier to raise oneself from a higher sitting position Therefore if the bed can be raised use this function in order to facilitate the raising procedure for the patient 2 Let the patient lean forward at the same time as he she raises himself herself to a standing position using the arm and leg muscles Assist by holding the seat frame to stabilize the position of the RollOn 3 Once the patient is standing turn down the guide handles to allow the rear supports to be placed behind the patient This is e
Download Pdf Manuals
Related Search