Restoration Notes
Contents
1. Altonah Utah 84002 12 Automatic Transmission The 1952 thru 1954 Kaisers used a GM Hydramatic transmission It was almost identical to the models used in the Pontiacs and Oldsmobiles which can be used for replacements Even the column mounted shift indicator was the same The Cadillac Hydramatic was similar but not identical This model of the Hy dramatic transmission had no designated Park position The Reverse position was used as Park Parts Parts are readily available and good used units are easy to locate 13 Driveshaft The driveshaft consists of one balanced tubular shaft and two cross type universal joints that are grease able The shaft passes through the center X member of the frame Parts Parts are readily available The universal joints are of the common type used on several other makes Used shafts can be obtained from recycled cars or any competent driveline shop can fabricate new ones 14 Differential All 1952 thru 1954 Kaiser shared the identical Dana 44 differential There were four drive ratios depend ing upon the model and the type of transmission installed Although there is no written specifications it is possible a few cars may have been equipped with the earlier Dana 41 The Dana 41 can be identified by a round bolt pattern instead of the oblong pattern of the Dana 44 The four rear axle ratios available were Transmission Rear Axle Ratio Hydramatic 3 54 1 Standard 3 90 1 Standar2. Brown 18530 W Yellowstone Rd Altonah Utah 84002 PREFACE I have complied these Restoration Notes in order to provide some guidance to those who own these unique American automobiles and for those who may be contemplating purchasing one The Kaiser automobiles were some of the most unique and quality American cars of the 1950 s and are a very pleasurable car to own restore show or drive They turn heads every where they go and their beauty and uniqueness always draw a crowd The Kaisers are not difficult to restore or maintain and most parts can be located with little effort Most me chanical parts were obtained from outside suppliers such as Borg Warner Auto Lite and GM so many parts are common with other makes The engines were built by Kaiser but since Kaiser also owned the Jeep line the engines were used in the Jeep as well even long after Kaiser had sold the Jeep line to AMC so most engine parts are not that difficult to locate However there are several items especially body and trim parts which a prospective buyer should inspect carefully since replacements are extremely difficult to locate in us able or restorable condition There items are identified in the detailed sections The Kaiser organization introduced many features that would later be found on other cars Kaiser produced the first Hatch Back car the first 4 door convertible the first post war supercharged car the first Safety First car and intr
3. Some NOS parts can be located 4 Glass All glass windshield door windows vent windows and rear windows are the same for all models Note Glass from a 1951 model will also fit except for the front windshield The 1951 s used a split 2 piece front windshield Glass from a 1954 will also fit except for the 3 piece rear window Parts Windshields are being reproduced by the Kaiser Club The door and vent glass is flat and readily available from any competent automotive glass shop although the tint for some cars may not match ex actly The curved rear glass is only available from parts cars 5 Frame The X frames for all 1951 through 1954 are basically the same and can be interchanged without any problem Although there were some very minor differences in 1952 and again in 1954 they are just a few holes which can be drilled in the earlier frames Note When the 1951 Kaiser was introduced the extremely smooth ride was quickly recognized by the buyers and envied by the other major manufactures The car rode better than many popular and much heavier cars Several of the other US car manufactures quietly purchased a 1951 Kaiser and stripped it down to analyze just why this Kaiser rode so smooth They credited the smooth ride to the excellent X frame spring rate and the positioning of the seats Their engineers would soon copy many features of the Kaiser design As outlined above they would also copy many of the exterior body design feature
4. identical as earlier engines and will seem to Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002 fit but they do not The newer type rear oil seal conversion designed for the Jeep OHV 230 Tornado en gine should always be used but the rear filler block must be properly modified or a severe oil leak is guar anteed If the block requires an overbore of more than 20 thousands it is best to search for another block In no case should the block be bored more than 30 thousands It is best to not exceed 20 thousands If the cylinder walls are bored too thin they will overheat and warp causing massive engine failure Check the rods very carefully Obtain new rods if possible as they are prone to bend Be sure to have the cylinder block and cylinder head honed flat Once removed from the engine the heads are prone to warp if laid flat Stand them upright Do not over mill the heads Too much will increase your compression ratio leading to a requirement to use only premium gasoline 7 Body Mounts and Rubber Mounting Gaskets Reproduction rubber body mounting pads are avail able but are usually too thin and will need to be shimmed Reproduction rubber mounting gaskets for some of the trim such as hood and trunk emblems and light housings are available but do not fit very good A lot of time will be spent fitting the gaskets or making new ones from scratch None of the other trim mountin
5. recycled parts cars that can be restored and rechromed 18 Wiring Parts The Kaisers like all other cars of the 50 s widely used the old cloth wrapped wire Some of that is available but it is very difficult to match all the color combinations and wire types of the original wiring Some partial reproduction wiring harnesses are available In most cases you will need to furnish some of your original connectors and plugs Kits from several aftermarket suppliers may be used but the type of wire connectors and plugs will not match the original The new aftermarket kits do have much improved wire and insulation and are much easier to install than to try to make your own harness However they will not pass as original Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002 19 Major Problem Areas The major problem areas in restoring one of the Kaiser models listed in this section are 1 Locating replacement interior upholstery Nothing is being reproduced The Kaiser vinyl was very sturdy and most that you take from parts cars will be reusable The cloth upholstery is another matter After some 52 years most of it will be unusable You will have to search extensively in order to locate enough of the fabric Both the vinyl and the fabric will need to be dyed to match the original color A task not easily accomplished As explained in the Upholstery section the Dragon prese
6. to soft crankshafts The Kaiser built engines did not have this problem Parts Most internal engine parts are readily available from parts suppliers Hardest to locate are the crankshaft balancer timing chain crankshaft gear camshaft gear camshafts and camshaft bearings The crankshaft fan belt pulley for all cars power steering or standard is not available except from parts cars Crankshafts blocks heads pans and all covers are also only available from recycled parts cars 11 Standard and Overdrive Manual Transmission The standard transmissions and Overdrive units are common T 90 Borg Warner type The transmission is a synchromesh 3 speed manual unit On the Kaiser the transmission is shifted by means of a column mounted shift linkage The Overdrive unit provides a fourth gear with simple operation by removing the drivers foot from the gas pedal to shift up or pressing the gas pedal to the floor to shift up The Overdrive unit provides free wheeling which can be disengaged by means of a dash mounted pull cable for push starting etc The same Overdrive unit was used on many other makes of the period Parts Most internal parts are readily available from parts suppliers or obtained from recycled parts cars Most of the external shift mechanism and linkage must be rebuilt or obtained from recycled parts cars as none are being reproduced Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd
7. 02 1 Body Shell 4 Door Sedan Models The 1952 1953 and 1954 4 door Specials shared the same body It was basically the same as the 1951 4 door body except for very minor differences The1952 54 front and rear bumper splash shields are different from the 1951 models and the 1953 54 rear fenders were drilled to accommodate the larger tail light housings and fins The stainless bottom side trim mounting holes were drilled differently for the Specials and the Manhattans The 1952 and 1953 4 door Manhattans shared the same body as the Specials It was basically the same as the 1951 4 door body except for the very minor differences explained above 2 Door Sedan Models The 1952 1953 and 1954 2 door Specials shared the same body It was basically the same as the 1951 2 door body except for the very minor differences as ex plained for the 4 door above The 1952 and 1953 2 door Manhattans shared the same body as the Specials except the stainless bottom side trim mounting holes were drilled differently for the Specials and the Man hattans Club Coupe The 1952 Club Coupe body was unique to only that model but the body was ba sically the same as the 1951 Club Coupe Deluxe and Business Coupe body except for very minor differences as explained for the 4 door above The stainless bottom side trim mounting holes were drilled differently for the Specials and the Manhattans This body style was pro duced in the 1952 Business Coupe and Manhattan mode
8. Use your Browser Back Button to Go Back Restoration Notes 1952 1953 Kaiser Special 1952 1953 Kaiser Manhattan 1953 Kaiser Dragon 1954 Kaiser Early Special Note The 1954 Early Special used fully completed leftover 1953 Kaiser Manhattans and had the very luxurious Manhattan interiors Only the front clip and tail lights was changed out to the 1954 design Therefore the Early 1954 Specials also have the smaller 1953 one piece rear window Later produced 1954 Specials used the new 1954 body with the three piece rear window Their interiors were not as plush as the Early Specials Special Note The 1952 Kaiser Virginian Model is not covered here Although this model is listed as a 1952 year model they are really left over 1951 cars that were re serialized with 1952 serial numbers Some of these cars had Continental Tire Kits installed by the factory while others had a two tone paint scheme applied to them They are in fact 1951 cars in every respect except for the serial number and black plastic hood ornament inserts Contents 1 Body Shell 11 Transmission 2 Front Clip Standard amp Overdrive 3 Doors 12 Automatic Transmission 4 Glass 13 Driveshaft 5 Frame 14 Differential 6 Suspension 15 Exterior Trim 7 Wheels 16 Interior Upholstery 8 Brakes 17 Interior Trim 9 Cooling 18 Wiring 10 Engines 19 Major Problem Areas Copyright 2005 2007 All Rights Reserved Kaiser Bill
9. d 4 09 1 Standard with Overdrive 4 55 1 There is a metal tag attached to the rear differential cover that lists the number of teeth on the drive gear larger number and pinion gear smaller number To determine the ration divide the larger number by the smaller number Note This same differential was also used on various Jeep models at least through 1967 and Ford 4 wheel drive trucks as the front differential Parts Parts are readily available from parts suppliers Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002 15 Exterior Trim All exterior trim is unique to the specific models The bottom stainless trim was wider on the Manhattan models and thinner on the Deluxe The Dragon models shared the same trim as the Manhattan but the hood ornament hood emblem and trunk emblem were all real gold plated instead of chrome The 1954 Special came with the larger 1954 tail light assemblies and rear fender trim and will not interchange with the earlier models The front and rear bumpers are the same for all models except the front bumper on the Early 1954 Special used the same as the 1951 models The grill parts are identical except the 1954 Early Special which had the 1954 grill None of the 1954 grill parts will interchange with the earlier models Parts Reproduction plastic trunk and hood emblem inserts and tail light lens are available for the 1952 and 1953 mod
10. duced the world s first Hatch Back in 1949 This original Kaiser design was personally ordered built by Henry J Kaiser himself There is a interesting story as to the event that prompted Henry Kaiser to order this model to be put into production Parts A limited number of reproduction body parts are available Reproduction outer rocker panels partial floor panels and rear fender well repair panels are available Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002 2 Front Clip All 1952 and 1953 models used the same front clip radiator support inner fenders fenders grill bumper splash shield hood and grill The radiator support was factory modified for those 1953 cars with power steering Note Although the hood does interchange it was drilled differently for the hood emblem Also the 1951 radiator support inner fenders fenders and hood are not the same but can used with slight modifica tions The 1954 Early Special used the new 1954 front clip and no parts will interchange with the earlier models Parts No reproduction parts are available Some NOS parts can be located 3 Doors Doors of all 4 door cars of any of the models listed above will interchange The doors for the 2 door cars and the Club Coupe will interchange The front door of the 4 door models will not fit the 2 door or Club Coupe body Parts No reproduction parts are available
11. els No other reproduction exterior trim parts are available Some NOS parts can be located Except for plastic parts there are sufficient parts available from parts cars except the headlight trim rings and rear fender fin trim for the 1954 Early Special which are difficult to locate 16 Interior Upholstery The interior upholstery is one of the most attractive features of these cars and is unique to these specific models The Kaiser vinyl is very sturdy and most of the original will be in reusable condition Parts There is no reproduction upholstery available Some material may be located from parts cars but it is over 50 years old The vinyl may be good but the cloth material is rarely usable Note The Dragon used special upholstery material that is unique to the Dragon only and is especially dif ficult to locate from parts cars The Dragons also used two different types of padded vinyl tops that cannot be matched with known current production materials 17 Interior Trim All interior trim is unique to these specific model except some of the interior trim is identical to the 1951 Kaisers The Dragon has a unique gold plated plaque attached to the glove box that identified the original buyer by name It was reproduced but the supply has been exhausted Parts There are no reproduction parts available Some NOS parts may be located Except for plastic parts and the Dragon dash plaque there are sufficient parts available from
12. ential housing is unique to the Kaiser There were 4 different drive ratios available see the Differential Section Parts Reproduction springs are available but do not match the original Kaiser spring rate Shock absorb ers are available The differential mechanical unit is a Dana so parts are available 7 Wheels The Kaiser wheels are of a five bolt 4 1 2 inch pattern This same pattern was used by Ford in the 1950 s and 60 s A few of the Chrysler products also used this bolt pattern but there is no reliable interchange list available Since Kaiser owned the Willys Jeep line they used the same wheel bolt pattern on the Jeep When AMC purchased the Jeep line they continued using the same wheels until the early 1990 s Note A good source for new Kaiser wheels is your local Jeep dealer Even the 1988 Jeep special alu minum alloy wheels will fit Parts From your Jeep Dealer or from recycled parts cars 8 Brakes The front and rear drum brakes are Bendix type 4 design The brake shoes interchange with a few Nash Studebaker and Willys models The brake master cylinder and wheel cylinders also interchanges with other makes There were no Disc brake option available Parts Brake shoes master cylinders wheel cylinders brake hardware springs clips etc are readily available Brake drums are not being reproduced Some NOS parts can be located but drums are available only from recycled parts cars Copyright 2005 2007 Al
13. g gaskets are available and must be fabricated 8 Interior and Exterior Trim Except for the plastic parts mentioned in 2 none of the Kaiser trim is being reproduced so your old parts will need to be restored and or rechromed Recycled parts are available but most will also need to be rebuilt as well Other plastic parts and hubcaps are a particular problem and difficult to locate Hope this helps Kaiser SM Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002
14. l Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002 9 Cooling The radiator for all models is identical It is the same Harrison radiator used in the 1955 56 6 cylinder Chevrolets except the mounting brackets are different These can be swapped by any competent radiator shop There was no fan shroud on any model The water pump is identical on all models except those with power steering It has a slightly different housing Parts Radiator cores and tanks are available They are being reproduced for the Chevrolet NOS water pumps may be located and rebuilt water pumps are available Radiator mounting brackets are only avail able from parts cars 10 Engine The engine in the 1952 1954 Kaisers was a Kaiser built engine It is an 226 cubic inch in line flat head 6 cylinder engine This same engine was also used in the Jeep for many years The engines built by Kaiser and used in the 1952 54 Kaisers had Kaiser Supersonic script cast into the engine head All models listed in the heading used the same engine Note Kaiser had purchased the rights to the Continental engine back in late 1947 and redesigned it for additional power and improved reliability The Kaiser engineers improved the crankshaft increased the compression ratio and changed the valve timing Earlier cars produced in 1946 and 1947 used the origi nal Continental engine and did suffer some reliability problems The problem was contributed
15. ls There were no 1953 or 1954 Club Coupes produced The Club Coupe and Business Coupe is admittedly the best looking of the Kaiser bodies and the model most desired by collectors Note The 1951 thru 1954 Kaisers were praised as the best looking American car It was awarded many international awards for its beauty of design Many of the exterior features of the 1951 thru 1954 Kaisers would soon be copied by every US car manufacturer The rear fender Darrin Dip would first be copied by Chevrolet for the new 1955 Chevrolet Almost every US car maker would soon copy this Dip Ford would be the next to copy the Dip for the 1965 Mustang Most others would soon follow The rear window backward slant was also copied by many The front and rear window Sweetheart shape would remain a unique Kai ser design feature Traveler The 1952 and 1953 Kaiser Hatch Back Traveler has a body unique to that model only It was produced as both a 4 door and 2 door in the Deluxe and Manhattan models The 1951 1952 and 1953 bodies are all the same except for the mounting holes for the side trim and the difference explained for the 4 door sedan bodies The bodies are not interchangeable with any other model however some patch panels may be cut from other Kaiser models such as the rear quarters and the roof The front window cut out is the same but the rear window cut out is different There was no 1954 Traveler produced Note Kaiser pro
16. nts specific problems in this area 2 Locating replacement plastic parts interior and exterior The only plastic parts that have been re produced are the hood and trunk emblem inserts and tail light lens for the 1952 and 1953 models and the supply of them is running low All other plastic replacement parts must come from recycled parts cars or you must have them reproduced A costly venture Reproduction steering wheels are available from the Kaiser Club but the color is not an exact match and the rims are thicker 3 Locating the proper tinted glass Although the Kaiser Club KFOCI has reproduced some wind shields the tint and shading does not correctly match the original The curved rear windows are not being reproduced and must be obtained only from recycled parts cars This used glass usually has minor imper fections at best The tinted flat glass available from your local glass shop does not match the original tint color If you replace any glass you will need to replace all of it There are glass companies that will repro duce curved glass for you but it is very expensive and the reproduced piece does not always fit and rarely matches the original tint 4 Hood hinges NOS hood hinges do show up from time to time but the Kaiser hood hinges are prone to wear badly They rarely operate properly after two years and these cars are over 50 years old The one company that previously rebuilt the Kaiser hinges will no longer do so They sa
17. oduced the bright color coordinated exteriors and interiors to the automotive industry The Kaiser automobiles were given many international awards for beauty and style Howard Darrin who designed the streamlined 1951 1955 Kaiser body lines was a famous world class de signer who designed many of the custom bodied luxury cars of the 1930 s and 1940 s for the European manu facturers as well as the American car companies His design of the Kaiser Darrin Sports Car was proba bly his most memorable It remains one of the best looking cars to this day and is the most sought after Kai ser model I have been involved with the Kaiser and Frazer Automobiles since 1946 My Dad was a Kaiser Frazer Willys Dealer from 1946 until 1956 and I worked in my Dad s shop after school and on Saturday s during my High School days and thereafter upon my return from military service I now devote most of my time trying to help others by sharing what knowledge I have of these automobiles These notes are by no means complete and there may be some errors that I have not recognized but I hope these Restoration Notes will be helpful to those who read them NOTE There are several sources of interchange parts lists including the Hollander Interchange Manual All of the known lists are helpful but none are totally accurate or complete for the Kaiser cars Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 840
18. s as well Parts No reproduction parts are available Copyright 2005 2007 All Rights Reserved Kaiser Bill Brown 18530 W Yellowstone Rd Altonah Utah 84002 6 Suspension Front Suspension The front suspension parts are mostly unique to the Kaiser Many parts are inter changeable with earlier model Kaisers especially the 1949 and 1950 models Some parts are identical to other US makes such as the shock absorbers wheel bearings and seals Several Buick and Oldsmobile front springs will interchange but the spring rate is not identical to the Kaiser Some parts of the A arms also interchange with other makes but there is no reliable complete interchange list Power Steering Power Steering was offered on all 1953 models and on the 1954 Early Special It was not an option on the 1952 models It was a Monroe Linkage Type This same system was also used on Dodge Ford Hudson Mercury Nash Packard and Plymouth cars Note This power steering system was often criticized as being too sensitive It required very little steer ing input and lacked the steering feel most customers were used to It was easy to over correct the car at high speed Parts No reproduction parts are available but any good rebuilding shop can rebuild your unit Rear Suspension The rear springs are unique to the Kaiser The shock absorbers are interchangeable with other makes but there is no reliable complete interchange list The rear differ
19. y it just is not profitable as the labor is too extensive They did a superb job They used new springs and installed pins much better than the original Your only choice now is to locate a local shop that will tackle rebuilding the hinges or try to rebuild them yourself Be extremely careful as the spring is capable of causing severe injury 5 Repairing rusted areas The Kaiser models in this listing are prone to severe rust in several areas Bottom lip of hood rear fender under tail lights bottom trunk lip front floors rocker panels rear fender wheel wells interior trunk sides Reproduction rocker panels partial floor panels and upper rear wheel wells are available but they are not identical to the original and amounts are limited Replacement hoods and trunks are available from recycled parts cars but most recycled ones will have some of the same rust problem 6 Engine Even though the Kaiser engine is very reliable and will last over 150 000 miles in normal use most restorers will want the engine rebuilt The engine has soft valve seats which can easily be burned by the use of non leaded gasoline so new hardened valve seats are a must The Kaiser engine is not famil iar to many rebuilding shops and there are several cautions that should be followed The timing method for a rebuilt Kaiser engine is not common It is not set to cylinder number 1 as most engines Careful study of the Kaiser Service Manual is a must The distributors appear
Download Pdf Manuals
Related Search