Home

OPERATION & SERVICE MANUAL

1. DE720 Rev E 62 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS FREEZER DOOR AND PRODUCT DOOR ITEM NO DESCRIPTION PART NO 1 FRAME GLASS HORIZONTAL 24 61 LENGTH PL726 2 BEZEL SNAP HORIZONTAL 25 38 LENGTH PL729 3 FRAME GLASS VERTICAL 35 25 LENGTH PL727 4 BEZEL SNAP VERTICAL 37 11 LENGTH PL728 5 HINGE PRODUCT DOOR HA735 6 PRODUCT DEFLECTOR PL735 7 ASSEMBLY PRODUCT DOOR SA112 8 BEZEL SNAP VERTICAL 37 11 LENGTH PL728 9 FRAME GLASS VERTICAL 35 25 LENGTH PL727 10 LOCK FREEZER DOOR ST705 11 GLASS HTD 3PANE 3TEMP 25 13 X 35 13 GL720 12 FRAME GLASS HORIZONTAL 24 61 LENGTH PL726 13 BEZEL SNAP HORIZONTAL 25 38 LENGTH PL729 14 SEAL FREEZER DOOR RE721 15 SEAL PRODUCT DOOR RE720 16 ACTUATOR ANTITHEFT ST724 17 SPRING PROD DOOR RETAINER HA720 18 CLIP SPRING MOUNT PRODUCT DOOR FA744 19 RIVET TREE NYLON BLK 1 4 FA743 20 BEARING HA724 21 COVER WIRING FREEZER DOOR PL723 22 BRACKET ANGLE DOOR ST704 DE720 Rev E 63 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS VC1100 CABINET
2. S E DE720 Rev E 64 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS VC1100 CABINET ITEM NO DESCRIPTION PART NO 1 EVAPORATOR RE724 2 MAGNETIC FREEZER DOOR EL779 3 SERVICE DOOR MOUNT TOP RIGHT WE101 4 CONTROL BOARD 120 SELECT 67196 2 EL733 5 PAGE 66 6 RAIL TRAY LEFT TILT ST734 7 LOCK BAR CABINET ST792 8 AIR FILTER 14x20x1 HA725 9 BEARING HA724 10 SCREEN BASE VC1100 PERF GALV 8776100 11 FOAM DROPBOX IN722 12 BASE CABINET 81779700 13 LEVELER HA728 14 ANTFTHEFTFLAP WE104 15 HINGE ANTI THEFT MOUNT HA727 16 RAIL TRAY RIGHT TILT ST735 17 MOTOR INTERFACE BOARD EL737 18 MOUNT FLAT CABLE FA756 19 _ FREEZER DOOR MOUNT TOP LEFT WE102 LIGHT FIXTURE 115V LAMP VC1100 35W PHILLIPS EL761 LAMPHOLDER FIXED LEVITON 465 EL762 LAMPHOLDER PLUNGER LEVITON 464 EL763 END CAP LAMP 2EACH EL794 SLEEVE LAMP 20 EL853 LEXAN COVER PL721 LIGHT HOUSING PL720 LIGHT FIXTURE 230V LAMP VC1100 40W 840K EL826 SOCKET LAMP EL824 RETAINER CLIP LAMP O HA738 LEXAN COVER PL721 LIGHT HOUSING PL720 DE720 Rev E 65 VC1100 For more information visit
3. ITEM NO DESCRIPTION PART NO 1 TRAY 2 DIVIDER TRAY 3 LABEL HOLDER PRICE amp LOCATION 4 COIL RH 07 VEND 3 00DIA 5 COIL LH 07 VEND 3 00DIA 6 TRAY DIVIDER LOCK 7 RETAINER HUB VEND MOTOR 8 SHAFT ADAPTER VEND MOTOR 9 MOTORMOUNT RUBBER STOPPER 10 PIN CLEVIS VEND MOTOR MNT ALUM 11 MOTOR VEND 24DC SEALED 12 SA VEND MTR DUAL 13 TRAY DIVIDER LOCK RUBBER DE720 Rev E 54 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 VC1100 STANDARD TRAY 3 COLUMN PARTS ITEM NO DESCRIPTION PART NO 1 TRAY WE112 2 COIL LEFT HAND 4VEND 3 00DIA WF724 3 DIVIDER TRAY VC1100 ST750 4 PIN CLEVIS VEND MOTOR MOUNT ALUMINUM FA778 5 MOTORMOUNT RUBBER STOPPERS FA754 6 RETAINER HUB VEND MOTOR PL730 7 SHAFT ADAPTER VEND MOTOR PL731 8 TRAY DIVIDER LOCK RUBBER FA763 9 VEND MOTOR EL801 10 LABEL HOLDER PRICE amp LOCATION PL740 11 LOCK DIVIDER ST751 DE720 Rev E 55 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS TRAY OPTIONS ITEM NO DESCRIPTION PART NO 1 COIL LEFT HAND 10VEND 2 50DIA WF720 2 2 COIL LEFT HAND 10VEND 3 00DIA WF721 0 3 COIL LEFT HAND 8VEND 3 00DIA 4 COIL LEFT HAND 6VEND 3 00DIA E 5 COILLEFT HAND 4VEND 3 00DIA WF724 6 COIL RIGHT HAND 8VEND
4. 37 Degree ceee ecce ee 37 Sensor rr rra F 37 SESI OUS SON NUT NU IM IUD iD aaa 37 56 On ee ee 38 Delta AERA ARAM Health 39 Defrost ee ee OA Discount Autoreinstate 44 Can Bottle n 45 Optie n 46 DE720 Rev E 2 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 Table of Contents SECTION 6 WIRING DIAGRAMS Refrigeration Interface Diagram mm MM M A7 High Voltage Ladder Diagram 115 48 High Voltage Ladder Diagram 220 240 Vac eee 49 Low Voltage Schematic 50 Power Panel Wire Locations 1 15 Vag ee 51 Power Panel Wire Locations 220 240 52 BualGoll Tray Wiring ne 53 SECTION 7 PARTS D al Tray 3 Column mm 54 Standard Tray 3 Column 85 Tray ODDS 56 Instructions for converting a 6 Column Tray to 5 Column Tray 57 Condensimg Unit 58 Evaporator Trim Service Door r RT 60 61 Freezer Door and Product Door Y VC1100 Cabinet 64 65 Electrical Panel 66 67 Cable Assemblies
5. naa 11 12 SECTION 5 PROGRAMMING The Service Mode of Operation e 13 Flow Chart Y 14 Diagnose u I ete 15 Error Motor Y 18 Count e a 18 Conio vo a i ZE 18 Account e 18 TASES AICS eee 18 Hist Count e e R s Sales i E 18 N Rdr Sales n nO 19 SetRanpe e e a 9 DE720 Rev E 1 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 Table of Contents SECTION 5 PROGRAMMING Range Cas e e 19 Range Vends SS 19 Clea s 19 Payout a susqikusan 20 Tube ico A I E 20 Exact Change ee 21 CS c 0 0 0 0 c 0 22 Test Vend m Test Relay 23 Menu 2 Serv Contr Price 25 Iems pue ecce uuu e uoce pee 25 Options su C 26 26 Forc Vend 26 Max Change ee 26 Value ee 26 Multi Vend n 27 Free Prod 27 Promo Vend tts Default 27 0 Model F 29 31 Messages n Options rr 32 POS AUX _ s m yD n HY n ns 33 POS 33 34 AUX 34 Time Date MM 35 Shutdown 20 7
6. 47 For more information visit www Gumball com 800 260 0010 1 214 550 5079 DE720 Rev E SECTION 6 WIRING DIAGRAMS VC1100 115Vac 60Hz HIGH VOLTAGE LADDER DIAGRAM 11 5 2 MAIN POWER SWITCH TB3 1 2 7 0 1 5 gt 4 1 2 SLO BLO Fe TB4 1 TB3 2 3 ovo 4 lt gt 4 4 LAMP BALLAST TBS 1 TBS 3 gt lt gt lt TBS 2 5 4 35 WATT LAMP TB3 1 je 18 19 gt TB4 1 EVAPORATOR r UR HEATER COIL sil a res 3 Fd I 1 AN MOTOR 1 5 TB2 1 EN T 4 4 MOTOR DRAIN HEATER 2 ite NN Fd I SABINET 204 WATT 1 4 SEE NUTE 1 TBI 3 E lion 1 e Er GLASS 3 HEATER SEE NOTE 2 TB6 3y YTB6 4 1 PRODUCT T L2 DOOR Lee HEATER FREEZER DOOR gt TB4 4 HEATER CONDENSING UNIT DEFROST 69 PEPRIDERATIN RELAY a e TB3 3 a 15 a TB3 4 5 1 2 SLO BLO TRANSFORMER FL TB3 e 6 7 8 TB4 e vac 29 9 NOTES 1 SWITCH OPE
7. SECTION 7 PARTS CONDENSING UNIT ITEM NO DESCRIPTION PART NO 115VAC 60HZ 1 3 4 HP CONDENSING UNIT 115V RE723 2 3 4 HP COMPRESSOR 115V RE738 3 FAN MOTOR 115V RE740 4 FAN BLADE RE744 220 240VAC 50HZ 1 3 4 HP CONDENSING UNIT 220 240 RE746 2 3 4 HP COMPRESSOR 220 240 RE742 3 FAN MOTOR 220 240 RE741 4 FAN BLADE RE744 EVAPORATOR ITEM NO DESCRIPTION PART NO 115VAC 60HZ 1 EVAPORATOR 1600BTU 115V RE724 2 EXPANSION VALVE 1 4TON ADJUSTABLE RE726 3 THERMOSTAT HEAT LIMITER 2 WIRES RE745 4 THERMOSTAT FAN DELAY 3 WIRES RE747 5 FAN MOTOR 115V RE748 220 240VAC 50HZ 1 EVAPORATOR 1600BTU 220 240 RE743 2 EXPANSION VALVE 1 4TON ADJUSTABLE RE726 3 THERMOSTAT HEAT LIMITER 2 WIRES RE745 4 THERMOSTAT FAN DELAY 3 WIRES RE747 DE720 Rev E 58 100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS TRIM y 72 Wil m 20 922 e N a9 PUSH d ITEM NO DESCRIPTION PART NO 1 TRIM BOTTOM FREEZER DOOR HA750 2 TRIM BOTTOM SERVICE DOOR HA751 3 TRIM SIDES FRZ amp SVC DOOR HA752 4 TRIM T
8. 67 SECTION 8 MAINTENANCE 68 SECTION 8 TROUBLESHOOTING 69 70 APPENDIX I MESSAGES 71 72 APPENDIX 2 DEX UCS RECORD SUBSET 73 DE720 Rev E 3 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 1 SPECIFICATIONS PHYSICAL CHARACTERISTICS e Height 72 in 183 cm Width 4 in 104 cm e Depth 32 1 8 in 82 cm e Weight 650 e Construction Heavy Gauge Steel Finish Powder Coated Paint e Number of Trays 5 e Maximum Selections 30 45 e Maximum Capacity 240 450 e Available coil sizes 4 5 6 7 8 10 12 16 ENVIRONMENT e Operating Ambient Temperature 50 F to 100 F e Location Environment Indoors only HEALTH AND SAFETY PROTECTION Vending of products is disabled e Activation Temperature Frozen Foods 0 F or higher if more than 15 minutes Slack Frozen 15 F or higher if more than 15 minutes Refrigerated 41 F or higher if more than 15 minutes None None ELECTRICAL AND REFRIGERATION REQUIREMENTS Power Requirements 110 120 Vac 60Hz Amperage Rating 16 Control Transformer Amp fuse Lamp Transformer 2 Amp fuse Compressor 3 4 hp Hermetic Refrigerant Charge 1 Ib 10 R 404A Evaporator Forced air Elec Defrost DE720 Rev E 4 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 2 INSTALLATION LOCATION Upon receipt of the unit inspect for any shipping damage and report directly to the carrier A d
9. Auto reinstatement Mode Disabled OFF Auto reinstatement Range Start row and End Row A Optic Sensor mode This is reset to the default setting of the corresponding machine types defined in the tables of the earlier default settings Range of Selections covered by Optic Sensor Start row A and End Row K All re settable fields Cleared DE720 Rev E 32 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING MENU 3 The following sub menu s can be accessed within MENU 3 POS AUX This submenu allows the operator to customize the point of sales messages gt POS Upon entry into this function the controller will display MESSAGE Using the keypad and the following keypad definitions entering in the new message will over write the old message Menu I is the default menu after each keypad entry from either menu the keypad will return to menu I To use menu II the SHIFT key must be depressed prior to the menu II key To save the length of the message the ENTER button must be pressed from within the Menu II If the maximum limit of 105 characters is entered the message length is automatically saved 3x7 keypad mapping BACK SPACE SHIFT SPACE Also associated with this menu are special function characters that allow a special effect or machine specific information to be included in the scrolling POS message
10. 123456789ABCDEFGHJK 4 000000000000000000000 GRN RED WHT BLK GRN BRN WHT GRY YEL O TYPICAL MOTOR CIRCUIT 24 VAC 24 VAC COMMON oa 2 IN4002 ROW PTIC OPTIC SENSOR SENSOR DETECTOR EMITTER Z cnuw DE720 Rev E 50 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 6 WIRING DIAGRAMS VC1100 115 Vac 60 Hz POWER PANEL WIRE LOCATIONS DE720 Rev E 51 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 6 WIRING DIAGRAMS VC1100 220 240 Vac 50Hz POWER PANEL WIRE LOCATIONS 15 10 9 REFRIGERATION GREENTT a l 3 INTERFACE BLACK al 28 CABLE TH 10 3 REFRIGERATION DEFROST RELAY RELAY A VIEW A dd VIEW REFRIGERATION DEFROST RELAY RELAY PAVAC 5 5 z P1 24VAC 24 VAC TRANSFORMER FUSE F2 LAMP BALLAST FUSE DRAIN HEATER swi MAIN POWER SWITCH DOOR HEATERS BLACK CABINET
11. CAUTION Setting a value greater than or equal to the maximum priced product in the machine will make all products within the discount range free This allows the operator to set the discount value that will be applied to those items that are defined in the RANGE menu A five digit number representing the current discount value appears upon entry to this function Using the numeric keys a value up to 5 digits may now be entered At any time this value may be saved with a press of the SAVE key The maximum settable value for discounting is equal to 199 99 for a scale factor of 1 and 999 95 for a scale factor of 5 If the operator attempts to save a value that exceeds this amount a warning message will appear and the displayed setting will revert to this maximum value DE720 Rev E 43 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING AUTOREINST This option allows the user to set a range of rows so that every time a product in the range is selected a vend attempt will be made even if the previous vend attempt resulted in no power ever being detected on a selection s motor Pressing the ENTER button after the user has navigated to the menu item labeled AUTORE INST accesses this option Pressing the ENTER button when any of the following functions are highlighted will pass control to that function To exit this menu or any of the functions within this menu without saving
12. Entry of a special function character involves entering first character followed by one or two letters The special function character sequences recognized by the 120 Select controller and their associated functions are listed in the following B When character is reached a space will appear and controller will beep D1 D2 Temperature of respective sensor will be displayed When character is reached scrolling will stop for 1 2 second Current time will be displayed in military format hours minutes 33 100 DE720 Rev For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING LANGUAGE This function allows the operator to choose a specific language in which sales mode messages will be displayed Upon entry into this function the controller will display one of the following nationalities along with an appended The displayed nationality represents the currently activated language The indicates that editing mode is active and that the operator may scroll through the available languages via the UP or DOWN buttons Pressing SAVE will activate the currently selected language and exit the menu To exit the menu without saving the selection press CANCEL See appendix 2 for message translations If AUX IL I ARY is selected out of the previous list then an alternative list of operator created sales mode messages will be used The
13. BLACK HEATER GREEN BLACK WHITE RO LIEN LIGHT WHITE 5 ETSI RED GABLE CABLE GREEN 8 TBS 5 v 230VAC 115VAC 230VAC 5 3 BLACK BROWN WHITE i t 5 EMI 24VAC 24VAC TI RED RED 6 18 8 AUTO TRANSFORMER 49 24 WHITE GREEN BLACK POWER CABLE GR 1 16 04 DE720 Rev E 52 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 WIRING DIAGRAMS DUAL COIL TRAY WIRING SECTION 6 SAVML YOLOW WAG NO LON S3OQ QNdA 1531 8 ON SHOLON ONILSIL NJ3HM ZON 9 ON 193135 SYOLOW YSISVN SHL 341 9093 AINO TIM 0408 TONLNOO 3H1 lAvidSId 38 TIM 5 024145 40 YSEWNN IN3SSOO JHL 193135 Q3M09IJNOO MOHS TIM AVIdSIO JHL ON 193135 JOMINOO JHL NO NOLING 0394 JHL SS3SHd SAVMI ONITIVISNI 14 76 MOVE AVAL ONIOY MGIA u SALON SSANYVH SOLON SHI SHJE8NDN 3 SSJ8NnN a SYSENNN a M3 44 0193 SOLON J31SVN E IAM HM 0 YVAN SIM SS3NHVH QD Nid WAP NOO Nid 9 2 0000009 YOLOW VC1100 53 DE720 Rev E t www Gumball com 800 260 0010 1 214 550 5079 VISI For more informat SECTION 7 PARTS VC1100 DUAL TRAY 3 COLUMN
14. If problems are encountered then the device name will be followed by an error code In the case of the Vending Machine Controller it s possible that a sequence of error codes could follow the VMC display if multiple errors are found with that device The diagnostics for the VMC will include an error code if any motor in the configuration has been flagged as bad In addition the error code for the bad motor will indicate why A definition of all possible error codes is shown in the table below This function may be exited at any time by pressing the CANCEL button ERROR CODE ERROR DESCRIPTION Too little motor current under 20mA For an example the display will show VMC 1 Too much time to complete vend 12 seconds i For an example the display will show VMC C2 2 NOVRAM checksum error The display would read VMC 4 Health amp safety error on temperature sensor 1 The display would read VMC 5 Health amp safety error on temperature sensor 2 The display would read VMC 6 The door is still open after 30 minutes 7 Eyes on the activated optical sensor are blocked Selection was not detected by optical sensor and as such is VMC 9 considered sold out For an example the display will show 9 Loss of changer communications or no changer CHANGER The display would show CHANGER 3 Loss of bill validator communications or no bill validator The d
15. To store the year and exit press SAVE DE720 Rev E 35 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING SHUTDOWN This option will allow the controller to shut down a range of selections or the entire machine based on four time of day intervals If the time falls within one of these intervals and the entire machine has been selected for shutdown then the customer lead through message V END NG OPERATION TO RESUME AT hh mm is scrolled If a range of selections has been chosen for shutdown that does not encompass the entire machine then the same message will scroll once for every time the customer makes a selection that falls within the range Note that for each time of day interval the customer can select from no days up to every day of the week on which the specified time intervals will be active For any given day these 4 time intervals may overlap one another Pressing the ENTER button after the user has navigated to the menu item labeled S T D OWN accesses this option Upon entry to the SHU T DOWN menu the current on off state of the shutdown option will be displayed as ON or OF F A press of ENTER will change the display to ON or OFF where the indicates editing mode Pressing ENTER again will toggle the on off state At any time the state may be stored and this function exited by pressing SAVE Pressing the ENTER button when any of the following functions are
16. Upon entry to this submenu the display will read DURAT ON Pressing UP DOWN will scroll through all the submenu items Pressing ENTER will enter the corresponding function of the selected item Duration Upon entry to this submenu the display will change to reading XX MIN where X X is the amount of time in minutes that the defrost cycle will run Pressing UP or DOWN will cause the time to increment or decrement by 1 minute in the corresponding direction The maximum and minimum value is 60 and 10 minutes respectively The time rolls over when the user scrolls through the maximum or minimum values At any point the modified value may be stored and this function exited by pressing SAVE Pressing CANCEL will exit the function without storing the value period Upon entry to this submenu the display will change to reading h m HRS Here h m represents the total amount of time in hours that a refrigeration cycle for either sensor must run before the defrost cycle will execute Pressing UP or DOWN will cause the time to increment or decrement by 1 half hour in the corresponding direction The maximum and minimum value is 24 0 and 5 hours respectively The time rolls over when the user scrolls through the maximum or minimum values At any point the modified value may be stored and this function exited by pressing SAVE Pressing CANCEL will exit the function without storing the value DE720 Rev E 40 VC1100
17. gt J Pl 3 Erg 4 77 COL O 123456789ABCDEFGHJK 1 lt BLK SIG lt BLK WH RED os RAM Pell ce RED RN BATA LINE 1 lale s 2 P6 BLU BLK a gra lt OR BLK A GRN BLK E REO BLK ho env A WH BLK u kow e BLU RED lt 8 MDB 120 SELECT E WD PORT 14 BLU CONTROLLER gut lt GRN 67196 EPROM Rov t OR RED H h ROW H 8 sep e mamam Be BATA UNE WHITE 3 PS o TEMPERATURE a tls zio 2 SENSOR mme HOUSING DEFROST RELAY nurpur lt REFG RELAY Z 3 IDUTPUT 1 rs lt GRN 5 SIGNAL GROUND lt BLK t gt SVDC p7 PERIPHERAL Zipang SVITCH INPUT SiREFG_ RELAY 1 eoz var INPUT iO Tse INPUT 12 lt 13 lt RED 14 lt Fa siGNaL_Gaouno i REFRIGERATION Healt amp DEFROST RED PB O bod RELAYS PERIPHERAL HERE 3 1 E 4444 3333 8 1 SIG GND ROW 7 INPUT VDC a 5 598 zz PPAR Bid 2 p LEI JUR ETE TEE DOOR SWITCH O O
18. or DOWN will scroll through the intervals 1 to 4 Pressing ENTER will redirect scrolling control to the D A Y field Pressing the UP or DOWN keys will scroll through the days of the week for the specified interval If CANCEL is pressed control passes back to the 1 to 4 interval field If ENTER is pressed control passes to the On off field Pressing of the UP or DOWN will toggle the daily status for the specific interval between ON and OFF Pressing CANCEL will return control to the DAY field At any point pressing SAVE will store the current status and return control to the interval field Note that presses of CANCEL will only force exit from this function while control is in the interval field DE720 Rev E 36 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING gt RANGE This allows the operator to set the range of rows that will be affected when shut down is active Upon entry into this menu item the user will see a display similar to SR ER J The user sets the first row in the range by selecting any letter from A through L The last row in the range may then be selected by entering any letter that is greater than or equal to the first row in the range A through L Once the 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these bu
19. 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these buttons forces exit from this submenu and returns control to the previous menu level A summary of the 4 settings is shown in the following table Health Safety Setting Basic Rule NONE Ignore health safety requirements for this sensor COLD Block designated rows if temperature exceeds 41 F 5 C for 15 minutes Block designated rows if temperature READS exceeds 15 F 9 C for 15 minutes Block designated rows if temperature ROA exceeds 0 F 18 C for 15 minutes The time requirements for FROZEN or SLACK levels do not apply for period of 75 minutes immediately following machine filling door open state servicing service mode button pressed or door open detected or a defrost cycle The time requirements for the COLD setting do not apply for a period of 30 minutes immediately following machine filling servicing or a defrost cycle DE720 Rev E 39 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING DEFROST This submenu allows the user to 1 Set the time DURATION for a defrost cycle 2 Set the time PERIOD between defrost cycles 3 Control the DELAY time at which the defrost cycle will start 4 Force a MANUAL defrost operation to run immediately
20. 36 Fahrenheit Delta temperatures for Sensor 2 6 Fahrenheit Health Safety Level for Sensor 2 COLD Health Safety Range for Sensor2 Start row and End Row Duration of defrost cycle 20 minutes Refrigeration period 12 hours Optic Sensor mode Disabled OFF Point of Sales message POS ENJOY A SNACK TODAY Refrigeration relay type Normally closed VC SLACK This menu is provided for setting the controller to operate a Vendtronics model VC1100 as a Slacked Frozen Food vending machine The following settings will be automatically changed after pressing the SAVE button CONTROL FUNCTION SETTING OF CONTROL FUNCTION Temperature Sensors 1 mode Enabled ON Set point temperatures for Sensor 1 10 Fahrenheit Delta temperatures for Sensor 1 6 Fahrenheit Health Safety Level for Sensor 1 SLACK Health Safety Range for Sensorl Start row A and End Row E Temperature Sensors 2 mode Disabled OFF Set point temperatures for Sensor 2 10 Fahrenheit Delta temperatures for Sensor 2 6 Fahrenheit Health Safety Level for Sensor 2 SLACK Health Safety Range for Sensor2 Start row F and End Row K Duration of defrost cycle 20 minutes Refrigeration period 12 hours Optic Sensor mode Disabled OFF Point of Sales message POS ENJOY A SNACK TODAY Refrigeration relay type Normally closed DE720 Rev E 100 For more information visit www Gumball
21. 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING Menu 2 The following sub menu s can be accessed within MENU 2 SERV CONTR This password accessible menu allows the operator to control which menus will appear during navigation of the service mode The only menus not under this control are MENU 2 MENU3 and this menu The user enters this menu by pressing the ENTER button after navigating to the menu item labeled SERV CONTR Upon entry to this menu the controller will display PASS and request that the operator enter a password The procedure for entry of the 4 character password follows the same method used for programming POS messages Please contact your distributor for password HELP If password entry is left early or if the password entered is incorrect then the menu is exited and menu navigation control passes back to the higher level If the password entered is correct then control passes to the next lower level At this point the display will read D AGNOS E which corresponds to the first selection that appears upon entry to the service mode The operator may now either 1 Scroll through the remaining functions in the menu which correspond to all of the configurable menus in the service mode 2 Enter a function by pressing the ENTER button 3 Exit this whole menu by pressing the CANCEL button which returns control to the menu just above the S CONTR menu should be pressed If any of the men
22. APPENDIX 1 LANGUAGES The following messages will be affected by the language selection and will be stored in the controller memory to be displayed as described in section 5 Message 1 English Italian Dutch Spanish Danish French German Message 2 English Italian Dutch Spanish Danish French German Message 3 English Italian Dutch Spanish Danish French German Message 4 English Italian Dutch Spanish Danish French German DE720 Rev E PLEASE INSERT EXACT MONEY PER FAVORE INTRODURRE I PRECISI SOLDI AFGEPAST GELD IN WERPEN POR FAVOR DEPOSITE CANTIDAD EXACTA PLEASE INSERT EXACT MONEY INDKAST AFTALTE PENGE FAITES L APPOINT PLEASE INSERT EXACT MONEY ABGEZAHLTES GELD EINWERFEN PLEASE INSERT MORE MONEY PER FAVORE INTRODURRE PIU SOLDI MEER GELD IN WERPEN POR FAVOR DEPOSITE MAS DINERO PLEASE INSERT MORE MONEY INDKAST FLERE PENGE MONTANT INSUFFISANT INTRODUISEZ D AUTRES PIECES PLEASE INSERT MORE MONEY MEHR GELD EINWERFEN MAKE ALTERNATE SELECTION FARE UNA ALTRE SCELTA ANDERE KEUZE MAKEN SELECCIONE OTRO PRODUCTO MAKE ALTERNATE SELECTION VAELG ANDEN VARE FAITES UNE AUTRE SELECTION MAKE ALTERNATE SELECTION ANDERE WARE WAHLEN PLEASE CALL SERVICE PER FAVORE CHIAMARE SERVIZIO SERVICEDIENST BELLEN POR FAVOR LLAMAR MANTENIMIENTO PLEASE CALL SERVICE TILKALD SERVICEMONTOR DEMANDEZ LE RESP
23. HON 330 IVa Lsnv S 39 553 4 NO NOG 39vSS3N AMVITIXNY 340 NHLI e 440 3975530 ss V9I83WV N 2 39vSS3W HON3UJ 330 G3ML lt 4 HDG L 35vSS3W lt NO 00 00 015 lt 66 GRUSS 3ovnoNvi 440 4 0000 1915 lt 4 222 AVQOL OWNS V lt NO NONI lt 00 00 90157 lt 39 553 4 lt 330 NONI lt 00 00 1 15 lt lt 0 HINOW lt 4 504 NASI lt 00 00 40192 lt hae xnv Sod 330 NASI 0090 13152 lt E 00 00 90151 6 gd 00 00 3WIL lt 00 00 14151 SNL 007000 NN3IN lt Q33n9l3NOO SNOILdO lt Q33f913NO2 lt 539 553 lt 0100 8 HJ IHY 10 LJ 1d NJZOMJ MOVIS OA 6109 OA 1300N lt Linvsad lt 39NV3 lt 1 NO lt 330 lt ONJA OWOHd lt 000 33 41 3384 lt NOS 330 lt 330 lt ILINW lt ANWA lt lt 330 lt 330 lt 39NVHO lt lt 440 lt QN3A 3930434 330 lt lt MOXOS 118 SNOILdO lt 103135 lt 5331 32149 lt 8916 SSVd SINOO NI3S lt 2 ANIN NO 330 NO 0 NO lt AN 440 lt NNSN lt 330 lt 330 lt 330 l
24. coins will continue to be paid out until the number is released 1 Most significant coin 2 Next significant coin 3 Next significant coin 4 Least significant coin gt TUBE FILL Upon entry into this function the controller will first display F LL COINS After a short delay the controller will change the display to show zero credit At this point the operator may begin entering coins into the changer As coins are entered the display will note the total value of the coins entered After returning to sales mode the credit will be zero This feature will be inhibited in the service mode If a credit exist from the sales mode before entering service mode UNCON ACCP The Unconditional Acceptance option forces the controller to accept any bill or coin less than a specified value regardless of whether the changer can return an equivalent value of credit All coins or bills equal to or less than this specified value will be accepted Upon entry to this function a five digit number representing the current unconditional acceptance value appears A value up to 5 digits may now be entered using the numeric keys This value may be saved at any time by pressing the SAVE key The maximum settable value for Unconditional Acceptance is equal to the largest denomination of currency or coin accepted by the changer or validator Ifthe operator attempts to save a value that exceeds this amount a warning message will appear and the displayed set
25. com 800 260 0010 1 214 550 5079 SECTION 5 gt VC FROZEN PROGRAMMING This menu is provided for setting the controller to operate a Vendtronics model VC1100 as a Frozen Food vending machine The following settings will be automatically changed after pressing the SAVE button CONTROL FUNCTION SETTING OF CONTROL FUNCTION Temperature Sensors mode Enabled ON Set point temperatures for Sensor 10 Fahrenheit Delta temperatures for Sensor 1 6 Fahrenheit Health Safety Level for Sensor FROZEN Health Safety Range for Sensor Start row and End Row E Temperature Sensors 2 mode Disabled OFF Set point temperatures for Sensor 2 10 Fahrenheit Delta temperatures for Sensor 2 6 Fahrenheit Health Safety Level for Sensor 2 FROZEN Health Safety Range for Sensor2 Start row and End Row Duration of defrost cycle 20 minutes Refrigeration period 12 hours Optic Sensor mode Disabled OFF Point of Sales message POS ENJOY A SNACK TODAY Refrigeration relay type Normally closed gt Dt Ift frz This menu should never be selected for use in a VC1100 gt Dt rht frz This menu should never be selected for use in a VC1100 gt BV COLD This menu should never be selected for use in a VC1100 gt MESSAGES This menu is provided to reset to the default Point Of Sales message of the corresponding machine types defined in the previous tabl
26. function that is used to create those messages is described in the following section gt AUX This function allows the operator to create custom messages that can be used in place of the customer lead through messages listed in appendix 2 Upon entry into this function the controller will display MESSAGE 1 At this point pressing UP or DOWN will scroll through the 7 other messages or at any time a press of ENTER will allow editing of the selected message Editing is done in the same fashion as the Point of Sales message If a message is saved during editing then MESSAGE n 1 will appear on the display After starting a new message the message must be saved before starting another function Each message length limit is listed in appendix 2 34 VC1100 DE720 Rev E For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING TIME DATE This option will allow the operator to set the time and date for timed operations Pressing the ENTER button after the user has navigated to the menu item labeled T DAT E will enter this menu Pressing the ENTER button when any of the following functions are highlighted will pass control to that function To exit this menu or any of the functions within this menu without saving settings the CANCEL button should be pressed gt TIME Upon entry to this function the current time of day will be displayed in a 24 hour format T IME hh mm
27. is opened an additional 15 minutes will also be provided whenever a defrost cycle occurs TEMPERATURE SETTINGS Temperature settings can be programmed for Degrees Fahrenheit or Degrees Celsius The Set Point can be programmed to maintain a desired temperature A minimum 6 F 14 C delta is recommended to prevent short cycling and extend the life of the Compressor The temperature may be viewed at any time by pressing the 0 button on the keypad DEFROST DELAY This option is only necessary if the customer would like the machine to defrost at a specific time This option allows the user to set the starting point for the first defrost cycle When a power loss to the Control Board has occurred 12 hours of operation will be resumed from the moment power was restored before defrosting DE720 Rev E 6 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 4 OPERATION REFRIGERATION SYSTEM The system is comprised of an Evaporator Condensing Unit and Electronic Control System The refrigeration system will shut down whenever the glass door is opened The System Control Board regulates all refrigeration functions the temperatures can be adjusted by entering the service mode and inputting the desired set point and delta temperature settings In the event of a Control Board failure the Refrigeration system will run continuously and will not cycle off until the Control Board is repaired or replaced
28. www Gumball com 800 260 0010 1 214 550 5079 SECTION PARTS ELECTRICAL PANEL 115V36 60Hz 220 240Vac 50Hz ad 8 9 9 9 0 0 0000 wooo LP T 27 DE720 Rev E 66 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS ELECTRICAL PANEL ITEM NO DESCRIPTION PART NO RELAY DPDT 30AMP 24VDC DEL275 TRANSFORMER CL2 115 24VAC 3A SWITCH ROCKER POWER 20AMP DPDT I OUTLET GFCI 120VAC 15 TERMINAL BLOCK 4 4 JUMPERED TERMINAL BLOCK 4 0 JUMPERED _ FILTER LINE 120 250AC 20A FUSE HOLDER PANEL MT BALLAST VC1100 35W 115V FUSE HOLDER PANEL MOUNT CE EL855 BALLAST 1100 40W 230V OSRAM CE TRANSFORMER 230 115 24 7 AMP EL823 N gt T CABLE ASSEMBLIES ITEM NO DESCRIPTION PART NO DISPLAY BOARD 120MDB EL740 VEND MTR HARNESS TPE 72 CA PERIPHERAL INTRF 120MDB CA KEYP
29. 1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING MOTOR This menu provides motor count and configuration options Pressing the ENTER button after the user has navigated to the menu item labeled MOTOR will enter this menu To exit this menu the CANCEL button should be pressed gt COUNT This function counts and displays the total number of functioning motors Pressing ENTER after the user has navigated to the menu item labeled COUNT starts it The controller will test each motor drive in the current configuration to determine if a valid motor is connected at that instant The message COUNT and the number of motors responding will then be displayed To exit this function press the CANCEL button gt CONFIG This function is used to remove undesired motor selections from the configuration Pressing ENTER after the user has navigated to the menu item labeled CONF starts it The controller will reconfigure to the currently functioning motors and display CONFIGURED This is the only means of removing motors from the configuration To exit this function press the CANCEL button ACCOUNT This menu provides functions for displaying the stored accountability Pressing the ENTER button after the user has navigated to the menu item labeled A C COUNT will enter this menu To exit this menu or any ofthe functions within this menu the CANCEL button should be presse
30. 1108 NV0 lt 330 1959 lt 440 3nL NO lt NO NOM 33 MS lt 440 lidt e 440 NOW JONVYE NO NO NNS lt lt 340 MnHly lt 4 340 NAS 3093 NO 4 0000 dOISL lt lt 4 440 lt 330 CaM lt SUH Z OL 9 00 00 INWISL lt ISNIBHOLNY lt b rM mi NO NOW TWANVN lt NIN 09 OL 01 lt esl 440 lt WANVN 330 lt 13102510 lt NO 5 lt SUH OL 0 140 NNSF NIN 09 OL 01 63 Nollwund lt 1504430 jio 195 lt NO Ride lt aoo wu3 us lt 1440 1846 lt 4 MIS viqaa lt NO lt N3Z033 404 01 4 0 HOG 340 MNHLE INON nana i 135 lt 4 330 lt NO dame lt 4 ZYOSNAS lt 330 03 lt lt NO 3nls lt 5 440 NO NONE ua HAs lt v v N3 us lt 340 NASE ovis we vgl 32033 440 lt N 304 01 4 0 lt 3NON T3 31 iNlOd 13S lt 330 lt NO 1752 lt 1 LYOSNAS lt dio Iye x NO lt 2 33493q NO 1830 lt 334930 lt EN 42 BYNLWYSdW3L lt N Hl do u3 Ns NO lt Ava 330 NO 3112 lt NO lt lt 4350 lt 430 3012 lt 330 lt NO NOW lt NMOGLOHS lt 330 NO NASZ lt 140 52 31vQ 3WlL lt xnv NO lVSI 8 39VSS3N HSINVO 330 1051 lt 2 39VSS3N HSINVdS NO 131 1 3408403 9 39VSS3N
31. 3 00DIA DUAL TRAY 7 HAND 6VEND 3 00DIA DUAL TRAY M 8 COIL RIGHT HAND 4VEND 3 00DIA DUAL TRAY WF727 00 9 COIL LEFT HAND 5VEND 3 00DIA 10 COILLEFT HAND 8VEND 2 50DIA 11 COIL LEFT HAND 7VEND 3 00DIA 12 COIL RIGHT HAND 7VEND 3 00DIA DUAL TRAY WF731 13 COIL RIGHT HAND 5VEND 3 00DIA DUAL TRAY 14 COIL RIGHT HAND 10VEND 3 00DIA DUAL TRAY 1 15 COIL LEFT HAND 12VEND 3 00DIA WF734 16 COIL RIGHT HAND 12VEND 3 00DIA DUAL TRAY 17 COIL LEFT HAND 16VEND 3 00DIA 18 CONVERSION KIT VEND MTR DUAL 1COL 4COIL 19 CONVERSION KIT VEND MTR DUAL 2COL 4COIL 2 20 CONVERSION KIT VEND MTR DUAL 3COL 4COIL 21 CONVERSION KIT VEND MTR DUAL 4COL 4COIL 22 CONVERSION KIT VEND MTR DUAL 1COL 6COIL SA119 23 CONVERSION KIT VEND MTR DUAL 2COL 6COIL 24 CONVERSION KIT VEND MTR DUAL 3COL 6COIL 25 CONVERSION KIT VEND MTR DUAL 4COL 6COIL SA134 26 CONVERSION KIT VEND MTR DUAL 1COL 8COIL 27 CONVERSION KIT VEND MTR DUAL 2COL 8COIL 28 CONVERSION KIT VEND MTR DUAL 3COL 8COIL 29 CONVERSION KIT VEND MTR DUAL 4COL 8COIL SA136 30 CONVERSION KIT VEND MTR DUAL 1COL 5COIL 31 CONVERSION KIT VEND MTR DUAL 2COL 5COIL 32 CONVERSION KIT VEND MTR DUAL 3COL SCOIL 5 128 83 CONVERSION KIT VEND MTR DUAL 4COL 5COIL 34 CONVERSION KIT VEND MTR DUAL 4COL 7COIL 35 CONVERSION KIT VEND MTR DUAL 3COL 7COIL 36 SCREW THUMB KNOB 6 32x1 2 37 PRODUCT RISER KIT 38 _ LINER TRAY 7 75INCH
32. 3 COLUMN TRAY 39 VEND MOTOR WITH COIL RETAINER ASSEMBLY SA115 40 PRODUCT PUSHER COIL LARGE BLACK 41 _ LABEL TRAY PROD PRICING 42 LABEL TRAY PRODUCT LOCATION A1 K9 DE728 DE720 Rev E 56 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS Instructions for converting a 6 Column Tray to a 5 Column Tray TRAY REMOVAL 1 Open service door and open the freezer door 2 Remove the product from the tray 3 Unplug the tray cable from the green mother daughter board located behind the trays on the inner back wall 4 Unlock the tray cable mount located on the left inner side wall near the back of the trays 5 Remove the tray from the machine by guiding the tabs on the back of the tray through the openings on the tray rails DISASSEMBLY 6 Remove the coils by pulling them directly out of the vend motors 7 Remove the divider lockbar and the grommet that holds the lockbar in place 8 Remove the dividers by pulling forward and upward 9 Remove the motor pins and rubber retainers from the motors 10 Unplug motor 6 from the harness and remove the motor from the tray ASSEMBLY 11 Replace the dividers in the appropriate slots for a 5 column tray you will have one extra divider left over 12 Position the motors in the middle of each column insert the motor pins and rubber retainers 13 Insert the divider lockbar into the slots on the dividers and fasten the lockbar to the tray with t
33. 8 TA301 TA302 101 102 PA201 203 204 PA303 EA201 EVENT IDENTIFICATION ONE FREE PRODUCT VENDS EA202 NUMBER OF EVENTS SINCE LAST RESET EA204 USER DEFINED FIELD VALUE EA201 EVENT IDENTIFICATION PROMO VENDS EA202 NUMBER OF EVENTS SINCE LAST RESET EA204 USER DEFINED FIELD VALUE EA201 EVENT IDENTIFICATION TUBE VALUE 05 10 25 1 00 EA204 USER DEFINED FIELD VALUE EA201 EVENT ID VALUE OF BILLS amp CASH BOX SINCE LAST RESET EA204 USER DEFINED FIELD VALUE EA301 EA302 EA303 EA304 EA305 DE720 Rev E 73 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079
34. AD INTERFACE 120MDB ICA DEX INTERFACE CA MOTOR INTERFACE 120MDB ICA REFRIGERATION INTERFACE 120MDB CA TEMPERATURE SENSOR 120MDB CA ELEC CONNECTOR FREEZER DOOR CABINET CA ELEC CONNECTOR FREEZER DOOR CA 2 PIN JUMPER FOR DUAL MOTORS CA 3 PIN JUMPER FOR DUAL MOTORS DE720 Rev E 67 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 8 MAINTENANCE The following section is provided for general maintenance of the VC1100 vending machine Preventative Maintenance Weekly Check for Error codes upon entering the service mode of operations Check the motor count to insure all motors are configured Check the Anti Theft Mechanism for proper operation Check the air temperature inside the refrigerated space for proper cooling Monthly Check the air inlet filter located on the left wall of the service compartment Check the air inlet screen located on the base of the service compartment for blockage Check the air outlet screen located on the back of the machine Empty the condensation bottle located in the service compartment Check the Evaporator fans Check the Condenser fan Check the heated Glass Annually Check the condensing coil for obstructions Check the condition of the legs for vandalism Test the defrost cycle for proper operation Lubricate the lockbar and linkages Check the condition of the door seals DE720 Rev E 68
35. ANTY TEMPERATURE DISPLAY The temperature sensor readings be displayed by pressing 0 in the sales mode of operation DE720 Rev E 7 100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 4 OPERATION REFRIGERATION CONTROL SYSTEM The following sequence describes a typical Refrigeration Control cycle Upon initial power up both compartments will begin to cool down The air temperature inside the refrigerated space cools down to the Cut Out setting The Control Board receives a signal form the Temperature Sensor 3 The Control Board energizes a 24Vdc Refrigeration Relay and opens the Normally Closed Contacts 4 The Compressor shuts off Evaporator Fans continue to run 5 The system remains off until the air temperature inside the refrigerated space warms up to the Cut In setting 6 The Control Board receives a signal From the Temperature Sensor 7 The Control Board de energizes the Refrigeration Relay and closes the Normally Closed Contacts 8 The Compressor starts up and the cycle is repeated until the unit goes into defrost pec DEFROST SYSTEM The Control Board controls the timing of the defrost cycle The Control Board will simultaneously energize a Defrost Relay and the Refrigeration relays When the Defrost Relay is energized the Normally Closed Contacts open and shut off the Compressor and Evaporator fans the Normally Open Contacts close and turn the De
36. CANCEL before SAVE will exit the function without storing the new rows 28 VC1100 DE720 Rev E For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING DEFAULT This menu provides functions that allow the operator to restore some or many of the controller s default settings Pressing the ENTER button after the user has navigated to the menu item labeled DEFAULT will enter this menu Pressing the ENTER button when any of the following submenus or functions are highlighted will pass control to that respective submenu or function Upon entry to the MESSAGES and OPTIONS functions the controller will display CONFIGURED indicating that the settings associated with the corresponding function are now in effect To exit any portion of this menu or any of the functions within this menu the CANCEL button should be pressed The following 3 sections contain tables showing those settings which take effect when the corresponding function is selected gt MODEL This function allows the operator to choose a specific set of default machine settings that correspond to the type of vending machine the 120 Select Controller will be used to control Upon entry into this function the controller will display one of the machine types listed at the top of each of the following tables along with an appended The displayed machine type represents the current machine configuration The indicates that edit
37. For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING Delay WARNING The user is strongly encouraged to set the current time prior to setting the delay Due to the fact that the refrigeration cycle is controlled by the controller s real time battery backed clock adjustment of the current time after the delay value is set can cause the defrost cycle to occur in a shorter interval of time than the actual value This is a result of the controller s effort to ensure that the refrigeration period always occurs at designated times during the day Any adjustment of the real time clock s value will not change these periods Upon entry to this submenu the display will change to reading 0 0 HRS Setting and saving any value other than 0 will override the current refrigeration cycle This new one time refrigeration cycle will go into effect immediately upon pressing the SAVE button After this one cycle has expired a defrost cycle will occur and the regular refrigeration period controlled by the current value of the PERIOD submenu will resume Adjustment of this value is accomplished by pressing UP or DOWN which will cause the time to increase or decrease by 1 half hour in the corresponding direction The maximum and minimum value is 24 0 and 0 hours respectively The time rolls over when the user scrolls through the maximum or minimum values At any point the modified value may be stor
38. ION 9 TROUBLESHOOTING Compressor does not run when main power switch is turned on 1 Unit not plugged in wall outlet 2 Building circuit breaker tripped 3 Defective compressor or starting components 4 Defective Refrigeration Relay 5 Cut out setting higher than the temperature inside the refrigerated space 6 System Control Board is programmed to disable refrigeration Machine will not cool to operating temperature 1 Dirty condenser filter or air inlet screen 2 Dirty condenser 3 Evaporator fans not working 4 Air leakage or bad door seal 6 Loss of refrigerant Te Ice buildup in the evaporator Evaporator fans not running 1 Faulty fan control thermostat inside the evaporator 2 Glass door switch is out of adjustment or is faulty 3 Loss of refrigerant 4 Unit in defrost Temperature displays 111 F 44 C continuously 1 Temperature sensor not connected 2 P7 connector on the control board not connected 3 System control board failure Temperature displays 32 F 0 C continuously 1 Faulty sensor 2 System control board failure CAUTION High voltages are located in areas of the unit that could cause severe injury or death Untrained personnel should only attempt the replacement of the bill acceptor the coin changer the front panel display the System Control Board and vend motors DE720 Rev E 70 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079
39. If credit exists upon entering the service mode it will be restored when the sales mode is re established At the time of initial entry into and final exit from the service mode the controller will briefly power all currently configured motors to determine if an open circuit condition exists Any configured motor that exhibits an open circuit during this process will be immediately removed from the vending machine configuration This means that a motor previously tagged bad in the sales mode due to an open circuit condition and presently found to have an open circuit condition upon entry to the service mode will not be flagged as bad in the diagnostics service mode menu For the remainder of the programming section the following commands will be used in place of keypad buttons 5 keypad buttons will be used to navigate the service menu A SCROLL UP B ENTER C SCROLL DOWN D SAVE E EXIT CANCEL DE720 Rev E 13 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 PROGRAMMING SECTION 5 AVS 5 39NYM lt Odds CT 330 lt 007000 440 lt 4 C js pela 4 OILdO lt WW 318004 N lt NO 195 tY 123135 dn TIOMOS V 5 dee lt 330 4 SONVY NO lt NO 330 YNHL 230 lt NO 03M lt 440 lt NO vst e m TEREN 31
40. NS ABOVE 75 2 TERMINALS 2 amp 3 SHORTED WHEN COIL IS gt 55 F TERMINALS 1 amp 2 SHORTED WHEN TEMPERATURE FALLS BELOW 35 F DE720 Rev E 48 1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 6 WIRING DIAGRAMS VC1100 220 240Vac 50Hz HIGH VOLTAGE LADDER DIAGRAM L1 PCT N SWI 28 MAIN POWER SWITCH TB3 1 2 1 gt TB4 1 2 AMP SLO BLO Fe TB4 1 TB3 2 3 4 lt TB4 4 230 Vac 230 Vac BLACK RED BALLAST 40 WATT LAMP 5 ITRANSF DRMER 19 TB4 1 EVAPORATOR _ 7 HEATER COIL Fe3 e npn FAN MOTOR 1 1 l m TUR MI DRAIN 7 HEATER 2 TB2 2 i HEATER URIS JsEE Nore 1 m TBI 3 TB2 3 N 22 107 re GLASS HEATER SEE NOTE TB6 3v vTB6 4 PRODUCT L DOOR HEATER FREEZER DOOR TB4 4 HEATER CONDENSING UNIT DEE RAST 58 RELAY a TB3 3 Jo 15 4 1 2 SLO BLO TRANSFORMER FL 230 Voc 230 Vac TB3 2
41. ONSABLE PLEASE CALL SERVICE BITTE KUNDENDIENST RUFEN 71 100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 APPENDIX 1 LANGUAGES Message 5 ENGLISH VENDING OPERATION TO RESUME hh mm Italian VENDING OPERATION TO RESUME AT hh mm Dutch VENDING OPERATION TO RESUME AT hh mm Spanish VENDING OPERATION TO RESUME AT hh mm Danish VENDING OPERATION TO RESUME AT hh mm French VENDING OPERATION TO RESUME AT hh mm German VENDING OPERATION TO RESUME AT hh mm Message 6 English MAKE SNACK SELECTION ONLY Italian DISPONIBILI SOIO LE SELEZIONI SNACK Dutch ALLEEN SNACK KEUZES Spanish SOLO DISPONIBLE PRODUCTOS EN ESPIRAL MAKE SNACK SELECTION ONLY Danish KUN VALG AF KONFEKTURE MULIGT French CHOISISSEZ UNIQUEMENT LES CONFISERIES MAKE SNACK SELECTION ONLY German NUR AUSGABE VON SUSSWAREN MOGLICH Message 7 English THANK YOU Italian GRAZIE Dutch DANK U Spanish GRACIAS Danish TAK French MERCI German VIEL DANK Message 8 English FREE ON US Italian FREE Dutch FREE Spanish FREE Danish FREE French FREE German FREE DE720 Rev E 72 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 APPENDIX 2 DEX FIELDS DEX UCS RECORD SUBSET 02 CA303 CA304 CA401 CA402 CA801 CA1001 CA1401 CA1403 TA201 TA202 TA203 TA204 TA205 TA206 207 TA20
42. OP FREEZER DOOR 753 5 TRIM SERVICE DOOR HA754 6 MOULDING BOTTOM FREEZER DOOR HA760 7 MOULDING BOTTOM SERVICE DOOR 761 8 MOULDING SIDES FRZ amp SVC DOOR HA762 9 MOULDING TOP FREEZER DOOR HA763 10 MOULDING TOP SERVICE DOOR 764 DE720 Rev E 59 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS SERVICE DOOR DE720 Rev E 60 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS SERVICE DOOR 1 COIN RETURN BUTTON 241 2 COIN RETURN ACTUATOR VC119 3 DISPLAY BOARD EL734 4 KEYPAD A THRUL EL736 5 T HANDLE HA247 6 LENS DISPLAY PL725 7 KEYPAD BACKPLATE 51710 8 MOUNT T LOCK ST711 9 COIN RETURN FLAP 51716 10 COIN OVERFLOW BOX ST714 11 LOCKBAR SERVICE DOOR ST785 12 LINK T HANDLE ST788 13 LINK LOCKBAR ST789 14 COIN OVERFLOW BRACKET ST790 15 COIN OVERFLOW RAMP 5 791 16 SERVICE DOOR WE120 17 COIN CUP WE121 18 COIN CHUTE VC110 61 VC1100 DE720 Rev E For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 7 PARTS FREEZER DOOR AND PRODUCT DOOR
43. The Evaporator removes heat from the air in a refrigerated space and transfers the heat to the liquid Refrigerant The liquid Refrigerant evaporates and is pumped out by the Compressor through the larger diameter tubing The Compressor pumps the low pressure vapor into the Condensing Coil where it gets rid of the heat and condenses into a high pressure liquid The high pressure liquid travels through the smaller diameter tubing to the T E V Thermostatic Expansion Valve The T E V controls the amount of refrigerant supplied to the Evaporator and the cycle is repeated The temperature can be viewed at any time by pressing the 0 symbol on the keypad CONDENSING UNIT The VC1100 uses a 3 4 hp Tecumseh Condensing Unit It is located on the base of the cabinet and can be accessed from the back of the unit It consists of a Compressor Condensing Coil Fan Liquid Receiver Starting Relay Start Capacitor Run capacitor and a Thermal Overload Protection Device Two service ports are provided for a Qualified Service Technician to diagnose and repair the Refrigeration System EVAPORATOR The VC1100 uses a low Temperature Forced Air and Electric Defrost Evaporator Each consists of an Evaporating Coil Thermostatic Expansion Valve Evaporator Fan 1 4 ton TEV and a Heating Element They are located inside each of the refrigerated spaces at the top WARNING UNAUTHORIZED ADJUSTMENT OF THE THERMOSTATIC EXPANSION VALVE WILL VOID THE WARR
44. VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 9 TROUBLESHOOTING Note Refer to the specific manufacturer s manual for the coin changer and bill acceptor No display on front panel 1 Transformer fuse bad 2 Display Board defective 3 System Control Board defective 4 Faulty display cable Selection will not vend 1 Vend mechanism binding on tray 2 Product jammed 3 Tray or motor connector unplugged or faulty connection 4 Bad motor 5 System Control Board defective Multiple vends from one coil 1 System Control Board defective 2 Defective motor switch Multiple vends from more than one coil simultaneously Defective motor Motor harness not plugged into the vend motor correctly Tray cable damaged Defective or damaged Motor Interface board System Control Board defective P Unit will not accept money 1 All prices are set to zero 2 Will not accept bills if coins in coin changer below minimum 3 Will not accept more than one bill if bill equals or exceeds the highest priced item 4 No power to System Control Board 5 Coin mechanism or bill acceptor defective Improper or no change 1 Out of coins 2 Bent coins or foreign objects in coin acceptor 3 Coin mechanism defective 4 System Control Board defective DE720 Rev E 69 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECT
45. We Take Cold Very Seriously VENDTRONICS OPERATION amp SERVICE MANUAL VC1100 Series MDB 120 Controller 67196 2 Software 120 Volts 60 HZ 230 Volts 50 HZ Seaga Manufacturing Inc 700 Seaga Drive Freeport IL 61032 USA Phone 815 297 9500 Fax 815 297 1700 www vendtronics com www seagamfg com A Member of the Jsa Family of Companies DE720 Rev E For more information visit www Gumball com 800 260 0010 1 214 550 5079 Table of Contents SECTION 1 SPECIFICATIONS Physical characteristics Environment TD 4 Heal safety prot ction d Electrical and Refrigeration Characteristics 4 SECTION 2 INSTALLATION Location n SECTION 3 INITIAL SETUP Vending c Dc C CC CC CC C i i Sa 6 Health and Safety Range XJ Temperature Settings ga a 6 cnt Delay Se 6 Refrigeration System P 7 Condensing unit rm 7 Evaporator meee 7 Temperature Display h 7 Refrigeration Gonlrol System eee 8 Delos S quem 8 System Control CMM ee ee 8 Door switch monn eee Idle Condition TB 9 COM Acceptance rr r ee Eust Bill Acceptance 9 Additional Bill Acceptance n QrL10 DEX UCS Data Retrieval n N 10 Vending
46. amage report will be necessary before contacting the factory Allow the unit to set at room temperature for at least 24 hrs before operation The unit should be stored or transported vertical at all times When relocating the unit it should not be tipped at extreme angles If the unit is relocated it is strongly recommended that a similar 24 hr non operating period be observed If the unit was in an operating mode prior to relocation the inside of the refrigerated compartment should be allowed to rise to room temperature and completely dry out before placing back into service The back of the unit must be located at least 6 inches from any obstruction to ensure proper airflow in the compressor area The system requires air to be induced from underneath the base of the unit through the air filter and condensing coil and expelled out the back of the vending machine POWER SUPPLY CONNECTION CAUTION DO NOT USE AN EXTENSION CORD The 110 120 Vac unit requires an independent 20 amp earth grounded circuit To insure safe operation of the VC1100 the power supply must be a properly grounded and a polarized outlet must be used Before plugging the VC1100 into the outlet test the outlet to confirm it will meet the VC1100 power requirements If the power requirements are not met contact a Licensed Electrician and have any necessary corrections made After connecting to the wall outlet open the Service Panel and turn the main power switch
47. ample 2 Set Point 36 F Set Point 36 F Delta 6 F Delta 10 F Switch on 39 F Switch on 41 F Switch off 33 F Switch off 31 F 38 VC1100 r more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING HEALTH This submenu allows the user to specify the operating region for passing health safety requirements and the range of rows over which the health safety requirements will be applied If the requirements are violated then those rows will be shut down accordingly Note that each sensor has independent health safety settings Upon entry to this submenu the display will read LEVEL Pressing UP or DOWN will scroll to RANGE level Upon entry to this submenu the display will change to reading either NONE COLD SLACK orFROZEN 7 These represent the basic health safety rules and the indicates that the controller is in an editing mode Pressing UP and or DOWN allows the user to scroll through the settings A selected setting may be saved and the menu exited by pressing SAVE To exit the menu without saving press CANCEL range Upon entry to this submenu display will change to reading SR ER A J The user sets the first row in the range by selecting any letter from A through L The last row in the range may then be selected by entering any letter that is greater than or equal to the first row in the range A through L Once the
48. and manually check all settings to insure the controller will function as they want it to This error will be cleared upon exiting the Service Mode of Operation Power surges are the most likely cause of a VMC 4 message VMC 5 A VMC 5 Error indicates that Sensor 1 air temperature in the refrigerated space has risen above the Health and Safety setting selected by the user All vending functions within a selected range of rows will be disabled and MAKE ALTERNATE SELECTION will be displayed If all rows are designated in the range PLEASE CALL SERVICE will be displayed This Error will be cleared upon exiting the Service Mode of operation e Frozen Foods 0 F or higher if more than 15 minutes e Slack Frozen 15 F or higher if more than 15 minutes e Cold 41 F or higher if more than 15 minutes e None None VMC 6 VMC 6 Error indicates that Sensor 2 air temperature has risen above the Health and Safety setting The VC1100 does not utilize a 2 sensor mode of operation and must be disabled DE720 Rev E 16 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING VMC 7 A VMC 7 error indicates that the reset switch at the top of the glass door has remained open for more than 30 minutes This error will be cleared upon exiting the service mode of operations VMC 8 A VMC 8 error indicates that the optical sensor is blocked the lens is dirty faulty sensor or the connector
49. ated as either cans or bottles will have an associated vend operation that differs from the normal vend operation Specifically after a valid product is selected the vend motor will run continuously until a product delivery sensor has signaled the controller or the maximum vend time of 9 seconds has expired gt Onoroff The current on off state of the can bottle option will be displayed as ON or OFF A press of ENTER will change the display to or OFF where the indicates editing mode Pressing ENTER again will toggle the on off state At any time the state may be stored and this function exited by pressing SAVE RANGE This item allows the operator to specify those rows of products that contain cans and or bottles Upon entry into this item the display will show something similar to SR ER A J The user sets the first row in the range by selecting any letter from A through L The last row in the range may then be selected by entering any letter that is greater than or equal to the first row in the range A through L Once the 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these buttons forces exit from this submenu and returns control to the previous menu level DEPTH This item allows the operator to specify each selection in the can bottle range as either a single depth or a double depth
50. buttons forces exit from this submenu and returns control to the previous menu level gt RANGE CASH Display value of all paid sales over the range defined in SET RANGE submenu since the last reset sum of PA204 fields in the defined range gt RANGEVENDS Display total number of products vended over the range defined in SET RANGE submenu since the last reset sum of PA203 fields in the defined range gt CLEAR This function allows the user to set all re settable fields to 0 Upon entry into the function those re settable items are cleared and the display shows CLEARED DE720 Rev E 19 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING COIN This function is provided for manually filling and dispensing coins from the changer In addition there are several functions for controlling credit acceptance and the display of messages related to credit status Pressing the ENTER button after the user has navigated to the menu item labeled enters this menu To exit this menu or any of the functions within this menu the CANCEL button should be pressed Pressing the ENTER button will enter all the following coin functions gt PAYOUT This function allows for the dispensing of coins from the inventory tubes Upon entry into this function the controller will display D SP EN S and wait for the user to press one of the following numbers The corresponding
51. crow and the customer will be allowed a credit return in a like coin fashion regardless of the force vend status Upon entering this function the display will show the current on off state as On or OFF Pressing ENTER again will toggle the on off state Pressing SAVE will store the setting and exit the function Pressing CANCEL will exit the function without modifying the setting gt FREE PROD This option allows a free product to be given to the customer at a preprogrammed interval When enabled every n product will be vended at no cost all accumulated credit will be returned and the message FREE ON US will be displayed during the vend process Setting this interval to 1 provides a free vend at every transaction 0 disables the option and the maximum valid interval is 255 Note that determination of free product status is made only after credit equal to or greater than the normal cost of a product has been deposited and the customer has selected the specific product Upon entry into this function the current interval will be displayed as FR E E X X X A new interval may be entered by pressing the numeric keys these will be displayed as they are entered The most significant digit followed by lesser significant digits It is not necessary to enter leading zeros and only the first three numbers will be used Pressing SAVE will store the setting and exit the function Pressing CANCEL will exit the function without
52. d Pressing the ENTER button may enter all the following accounting functions HIST SALES Display value of all paid sales since initialization VA101 which will rollover after 99 999 95 gt HIST COUNT Display total number of products vended since initialization sum of PA201 fields which will roll over after 79 999 920 gt RES SALES Display value of all paid sales since the last reset VA103 which will rollover after 9 999 95 gt RES COUNT Displays total number of products vended since the last reset sum of PA203 fields which will roll over after 79 999 920 DE720 Rev E 18 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING gt RDR SALES Display value of total card reader sales since initialization no corresponding DEX field which will rollover after 9 999 95 gt SET RANGE This allows the user to set a range of rows that will be tracked for accounting purposes Once this menu item the user will see a display similar SR ER A L The user sets the first row in the range by selecting any letter from A through L The last row in the range may then be selected by entering any letter that is greater than or equal to the first row in the range A through L Once the 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these
53. e as or OFF At this point the user may edit the On off State or scroll to the VALUE function using UP or DOWN Either function may be entered by pressing ENTER If the on off function is entered then the display will appear as either ON or OFF where the indicates editing mode Pressing ENTER again will toggle Maximum change s on off state Pressing SAVE will store the setting and exit the function Pressing CANCEL will exit the function without modifying the setting VALUE Upon entering the VAL UE function the display will show the currently programmed maximum change limit This limit may now be modified in the same manner as described in the price setting procedure DE720 Rev E 26 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING gt MULTI VEND This option will allow the customer to purchase more than one product if enough credit has been deposited When this option is active any credit remaining after a vend attempt is not automatically returned At this point the customer has one ofthe following options 1 Making another selection if there s enough credit 2 Depositing more money 3 Coin return of escrowed credit If Force Vend is also active then the customer will be forced to attempt the purchase of at least one item If a vend is attempted on a configured selection and the motor fails during this vend the credit will be placed in es
54. e entering a value press CANCEL or exit the service mode DE720 Rev E 21 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING TEST This menu provides functions that allow the operator to test motors and or relay output control lines Pressing the ENTER button after the user has navigated to the menu item labeled TEST will enter this menu To exit this menu or any of the functions within this menu the CANCEL button should be pressed gt TEST VEND This menu provides functions that allow the operator to test vend either individual motors or a range of motors Pressing the ENTER button after the user has navigated to the menu item labeled TEST VEND will enter this menu Upon entry to the function the display will read SELECT 222 To test vend a single motor the user should enter the desired selection s letter followed by its number To test vend a range of motors the user should enter the letter of the first row to vend followed by the letter ofthe last row to vend After entering the selection s if the operator is satisfied then the SAVE button should be pressed to initiate a vend attempt on the selected motor s Ifthe operator is not satisfied with the selection or if he she wants to exit the menu then the CANCEL button should be pressed and control will pass back to the higher level where TEST VEND will be displayed once again When the vend process is initiated the dis
55. e first bill will be accepted if the quarter tube is above the low indicator or if the dime and nickel tubes are both above the low indicators When accumulated credit is greater than or equal to the maximum price additional bill acceptance will be prevented When multivend is active then this maximum value increases to 3 times the highest priced selection in the machine If the bill acceptor offers escrow and acceptance is disabled because of the maximum price the last bill inserted will be kept in the escrow position otherwise the bill will go straight into the bill stacker Ifthe bill acceptor does not offer escrow or bill escrow is disabled the bill will go straight to the bill stacker The bill will be accepted if the coin tubes total cash amount is greater than or equal to the established credit plus the additional bill value If credit is established from a card reader no bills will be accepted DE720 Rev E 9 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 4 OPERATION ADDITIONAL BILL ACCEPTANCE Additional bills will be accepted if the dime and quarter tubes are both above the low indicators If the accumulated credit is greater than or equal to the maximum price additional bill acceptance will be disabled When multivend is active then this maximum value increases to 3 times the highest priced selection in the machine If the bill acceptor offers escrow and acceptance is disabled because of t
56. ed and this function exited by pressing SAVE Pressing CANCEL or saving a value of 0 will cause the submenu to be exited without any corresponding update of the refrigeration cycle gt manual Upon entry to this submenu the display will change to reading ON or OFF where the indicates editing mode Here ON or OFF represents the state of the Manual Defrost Mode Manual Defrost Mode allows the operator to instantly enable the defrost cycle The duration of this defrost operation will be equal to the length of time defined in the Duration menu item Pressing ENTER again will toggle the on off state At any time the state may be stored and this function exited by pressing SAVE Following expiration of the manual defrost operation a time period of 75 minutes must pass before an automatic defrost cycle can execute DE720 Rev E 41 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING DISCOUNT This option will allow the controller to discount specific items in the machine at pre programmed intervals Pressing the ENTER button after the user has navigated to the menu item labeled DISCOUNT accesses this option Pressing the ENTER button when any of the following functions are highlighted will pass control to that function To exit this menu or any of the functions within this menu without saving settings the CANCEL button should be pressed gt ONorOFF Upon entering into
57. es VC1100 DE720 Rev E 31 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 gt OPTIONS PROGRAMMING Service Menu Configuration All menus restored Diagnostic errors Cleared Accounting re settable Range Start row and End Row Exact change Value 0 Unconditional Acceptance Value 0 Bill Escrowing Enabled Force Vending Disabled Multiple Vending Disabled Free Product Disabled Maximum change Disabled Maximum Change Value 20 least coin factor Promotional Vending Disabled Promotional Vend Range Start row and End Row A Language English Time Hours value Time Minutes value Time Date value Time Month value Time Year value 0 0 1 1 0 Daylight Savings North American Rules Shutdown Disabled Shutdown Range Start row A and End Row A Shutdown Turn on Times 1 through 4 00 00 hours minutes Shutdown Turn off Times 1 through 4 00 00 hours minutes Shutdown Days 1 through 4 All days are turned off Temperature Unit of Measurement Fahrenheit F Discount Disabled Discount start time 00 00 hours minutes Discount end time 00 00 hours minutes Discount Days All days are turned off Discount Range Start selection A1 End selection Discount Value 0
58. f the PLEASE INSERT EXACT MONEY message and then return to the idle condition of the sales mode If a Promotional item in response to purchase of another item failed to vend the vend is considered good The failed motor is flagged and displayed in service mode If all previous checks have passed then a vend of the selection will be attempted DE720 Rev E 11 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 4 OPERATION A successful vend results in a display of the amount of change while it is returned using a least coins algorithm If the correct change is returned the THANK YOU message will be displayed for 0 8 seconds followed by the idle condition of the sales mode If for some reason the exact amount of change cannot be returned as much as possible will be paid out and the remaining amount will be retained as credit toward another vend An item price of 0 00 is allowed as a valid vend while in the sales mode of operation When a vend fails the controller will beep three times while the MAKE ALTERNATE SELECTION message is scrolled one time This will be followed by the amount of accumulated credit When the force vend feature is enabled faulty vends will result in an override of the force vend feature Force vend will stay overridden until the customer has attempted to escrow the credit or vended another product For those failed vend attempts of motors connected to the 120 Select cont
59. frost Heaters on The electric defrost is automatic and will be initiated every 12 hours The on time will be approximately 21 minutes During this period the compressor and evaporator fans are turned off Whenever power to the Control Board is removed the Refrigeration will run for a full 12 hrs before a defrost period begins The Defrost Start Time duration and period can be programmed from within the service mode of operation SYSTEM CONTROL The MDB 120 Selection System Control Board controls the message on the front Display Bill Acceptor Coin Changer Accumulation and Display of Escrow Issuing Change Payments Keypad Selection Vending of product Price Settings Health Safety and Refrigeration Control Functions The Sales Mode is the normal mode of operation The controller will always default to the sales mode under the absence of other inputs DE720 Rev E 8 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 4 OPERATION DOOR SWITCH MONITORING Both of the door switches will be monitored at all times if an open to close transition is detected then all health safety related errors timers and sold out errors will be reset If either glass door is opened the refrigeration system will be switched off If this open state exceeds 30 minutes thena DOOR OPEN ERROR message will be continuously scrolled across the display and the refrigeration system will be reactivated To protect the com
60. he maximum price the last bill inserted will be kept in the escrow position Ifthe bill acceptor does not offer escrow or bill escrow is disabled the bill will go straight to the bill stacker and the bill acceptor will be disabled after the second bill has been sent to the stacker DEX UCS Data Retrieval DEX UCS data retrieval is only allowed in the sales mode of operation The retrieval device initializes the data retrieval after it has been properly connected to the DEX port Refer to page 73 for the available DEX fields DE720 Rev E 10 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 4 OPERATION VENDING SELECTION The controller responds to keypad selections from two possible sources One source is the 120 Select controller s own keypad and the other source is a selection received from an MDB USD peripheral by the 120 Select Controller Following reception of any keypad selection the controller will then calculate a checksum of the MIS and pricing information The resulting checksum will then be compared to the previous checksum calculated when the controller last changed a MIS or price location If the two checksums are different the vend will not be allowed This same checksum error will cause the controller to return any deposited credit in a like coin fashion If the two check sums are identical then the selection s character number and price will be displayed while additiona
61. he rubber retainer 14 Insert the New coils into the motors end of the coil should be at 6 00 o clock position TRAY INSTALLATION 15 Slide the tray into the machine by guiding the tab on the back of the tray into the openings on the tray rails 16 With the tray pulled all the way forward and tilted snap the tray cable into the tray cable mount 17 Plug the tray cable into the green motor interface board TESTING 18 Press the red mode button on the controller 19 Press the A button twice then the B button twice to enter the test vend feature 20 Press the tray letter twice and then press save D button to initiate a test vend on all of the motors for that tray 6 COLUMN TRAY 5 COLUMN TRAY COLUMN DIVIDER COLUMN DIVIDER RUBBER RETAINER ll RUBBER RETAINERS Hl li 2 2 DIVIDER LOCK BAR DIVIDER LOCK BAR EO EO Ele Ele EIS FIG EXE FIG AM MI te 593 M 8 Y 4 REAR VIEW REAR VIEW MOTOR MOUNTING PIN RUBBER RETAINERS i Motor J DE720 Rev E 57 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079
62. highlighted will pass control to that function To exit this menu or any of the functions within this menu without saving settings the CANCEL button should be pressed gt TIME This function allows the start and stop times for shutdown to be programmed Upon entry into this function the display will show 1 STRT h h mm A new start time for this interval may be entered by pressing the numeric keys these will be displayed as they are entered The most significant digit followed by lesser significant digits It is not necessary to enter leading zeros and only the first four numbers will be used To save press SAVE The display will continue to 1 STOP hh mm A new stop time for this interval may be entered by pressing the numeric keys these will be displayed as they are entered The most significant digit followed by lesser significant digits It is not necessary to enter leading zeros and only the first four numbers will be used To save press SAVE The display will continue by increasing the leading 1 in the above examples to show the next shut down time When all four intervals have been programmed the controller will return to the previous level in the menu structure and ME will be displayed DAY This function allows the operator to designate days for the 4 separate shutdown times Upon entry the display willshow 1 DAY ON or 1 DAY OFF DAY designates a 3 letter abbreviation corresponding to the day of the week Pressing UP
63. ing mode is active and that the operator may scroll through the available machine types via the UP or DOWN buttons Pressing SAVE will reconfigure the default settings of the controller to correspond to those associated with the selected type and shown in the table In addition a press of the SAVE will force an exit from the menu To exit the menu without saving the selection press CANCEL The following tables list the default settings that apply to each of the different machine types and that are applied every time a machine type is saved Following the machine type tables is one additional table listing those default settings that are common to all of the machine types DE720 Rev E 29 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 VG COLD PROGRAMMING This menu is provided for setting the controller to operate a Vendtronics model VC1100 as a Refrigerated Fresh Food vending machine The following settings will be automatically changed after pressing the SAVE button CONTROL FUNCTION SETTING OF CONTROL FUNCTION Temperature Sensors mode Enabled ON Set point temperatures for Sensor 36 Fahrenheit Delta temperatures for Sensor 1 6 Fahrenheit Health Safety Level for Sensor COLD Health Safety Range for Sensorl Start row A and End Row E Temperature Sensors 2 mode Disabled OFF Set point temperatures for Sensor 2
64. isplay would read VALIDATOR 7 Loss of card reader communications or no card reader pem The display would read READER 8 DE720 Rev E 15 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING ERROR CODES Enter the service mode by pressing the red button on the controller a beep will be issued to recognize the transition and DIAGNOSE will be displayed until a function key is pressed Press the letter B to enter the diagnostics menu The diagnostics routine will present various error codes relating to the nature of a fault condition VMC 1 If any previously configured selection motor has become disconnected the Control Board will display VMC 1 after entering the Diagnostics Mode A successful Test Vend of the selection will clear this Error VMC 2 If any selection becomes jammed turns too slow or the home switch on the motor does detect the home position the Control Board will display a VMC 2 A successful Test Vend of the selection will clear this Error VMC 4 A NOVRAM checksum error indicates that some configuration information has changed erroneously Configuration information consists of prices and all option settings including health safety and temperature settings When the error occurs the controller does not know what information changed just that some information changed It could be a single location or all locations Your customer must go in
65. item SINGLE Items specified as single depth will vend for an additional 2 5 seconds following detection of the product delivery signal DOUBLE Items specified as double depth will stop the vend motor immediately following detection of the product delivery signal Upon entry into this item the display will show SELECT xx where xx represents the first selection in the can bottle range described above Pressing UP or DOWN scrolls through the additional selections in the range Pressing ENTER activates an edit mode for the displayed selection Pressing CANCEL exits the DEPTH function If ENTER was pressed the display will show either DOUBLE or SINGLE where indicates that the setting may be edited Pressing ENTER will toggle between the two modes The edited setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these buttons forces an exit from this submenu and returns control to the scroll menu level described in the previous paragraph DE720 Rev E 45 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING OPTIC This submenu provides the operator with options for designating ranges of product rows that will be monitored for product delivery by an optical sensor Selections that are designated as optical will have an associated vend operation that executed in an identical manner to non optical selections H
66. k 8 BLACK RED J TB4 2 BROWN TRANSFORMER NOTES 1 SWITCH OPENS ABOVE 75 F 9 2 TERMINALS 2 amp 3 SHORTED WHEN COIL 15 gt 55 F TERMINALS 1 amp 2 SHORTED WHEN TEMPERATURE FALLS BELOW 35 DE720 Rev E 49 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 6 WIRING DIAGRAMS VC1100 LOW VOLTAGE SCHEMATIC DISPLAY N GRY PRP BRN WHT RED ORN alu YEL BLK y le E ER 8 7 6 SI4 3TeTt P3 289922 252228 1 lt javac P6A lt
67. l checks on the selection are made in the following order 1 Passes Health and Safety rules 2 Item is not in Shutdown range of the Timed Shut Down Intervals feature 3 Item is in the configuration and it does not contain a bad motor 4 Deposited credit is greater than or equal to the price of the selection If the selection fails any of these checks then the vending attempt will be aborted The controller will continue to display the selection s character number and price for a period of 1 second This is followed with three beeps from the speaker along with the one time scroll of a failure dependent message e Ifthe item failed the shutdown check then this scrolled message will be VENDING OPERATION TO RESUME AT hh mm The deposited money will be automatically returned to the customer Ifcheck 4 failed then this message will be PLEASE INSERT MORE MONEY e For the other failures MAKE ALTERNATE SELECTION will be the message The credit or the point of sales message if no credit has been established will be displayed again following the message If the selection has passed all of the previous checks the controller will determine if the exact amount of change can be paid to the customer The vending sequence will be halted if the controller determines that exact change can not be returned The controller will return the deposited credit in like coin fashion The controller will issue three beep tones along with one scroll o
68. modifying the setting DE720 Rev E 27 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING PROMO VEND This function will allow a promotional product to be given to a customer for free in response to their purchase of another product When enabled purchasing selection 1 from one of the two possible promotional rows will result in both selection 1 and 2 of that row to vend sequentially Upon entering this submenu the display will show the current on off state as On or OFF At this point the user may edit the on off state or scroll to the RANGE function using UP and or DOWN Pressing ENTER may enter either function If the on off function is entered then the display will appear as either ON or OFF where the indicates editing mode Pressing ENTER again will toggle the on off state Pressing SAVE will store the setting and exit the editing mode Pressing CANCEL will exit the editing mode without modifying the setting RANGE Programming promotional rows is done in the RANGE function After entering this function the display will show SR ER X Y Where X and Y represent the promotional rows to be programmed row A row B etc Pressing the alphabetic keys may enter new rows The first entry will effect the center character and the second will effect the right most character To store the rows press SAVE after both entries are entered Pressing
69. new time may be entered by pressing the numeric keys They will be displayed as they are entered The most significant digit followed by lesser significant digits It is not necessary to enter leading zeros and only the first four numbers will be used To store the time and exit press SAVE MONTH Upon entry to this function the current month will be displayed in a numeric format as MONTH mm new month may be entered by pressing the numeric keys They will be displayed as they are entered The most significant digit followed by lesser significant digit It is not necessary to enter leading zeros and only the first two numbers will be used To store the month and exit press SAVE DATE Upon entry to this function the current date 1 31 will be displayed in a numeric format as DATE dd new date may be entered by pressing the numeric keys They will be displayed as they are entered The most significant digit followed by lesser significant digit It is not necessary to enter leading zeros and only the first two numbers will be used To store the date and exit press SAVE YEAR Upon entry to this function the current year will be displayed in a numeric format as YEAR yy New Year may be entered by pressing the numeric keys these will be displayed as they are entered The most significant digit followed by lesser significant digit It is not necessary to enter leading zeros and only the first two numbers will be used
70. on The display on the front panel should become active after approximately 20 seconds DE720 Rev E 5 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 3 INITIAL SETUP Upon placement of the machine on location the following programming should be setup to insure proper operation of the VC1100 Please verify the unit has reached the desired temperature settings before loading product The temperature may be viewed at any time by pressing the 0 button on the keypad VENDING Vending operations such as setting prices changing the message on the front display handling bills coins credit making change and operating vend motors should be tested before loading product into the machine Refer to Section 5 for programming instructions HEALTH AND SAFETY RANGE The function of this system is to provide additional user protection by disabling vending operations PLEASE CALL SERVICE will be displayed if the air temperature inside the refrigerated space rises above the selected setting for a preset period of time Proper Health and Safety settings must be set for proper operation Frozen Foods 0 F or higher if more than 15 minutes Slack Frozen 15 F or higher if more than 15 minutes Refrigerated 41 F or higher if more than 15 minutes None None A magnetic switch is located at the top of the glass door that will provide an additional 60 minutes whenever the service door
71. on header P8 is disconnected This error cannot be cleared until the problem is resolved 9 9 error indicates that the optical sensor did not detect product These errors will be automatically cleared by either opening and closing the glass door or exiting the service mode CHANGER 3 If the Coin Changer becomes disconnected from the Control Board i e Broken wire Faulty Control Board or Faulty Coin Changer CHANGER 3 will be displayed This Error cannot be cleared until the source of the problem is repaired If the VC1100 uses a Debit Card Reader without a Coin Changer or Bill Acceptor CHANGER 3 will always be present and cannot be cleared this is normal VALIDATOR 7 If the Bill Validator becomes disconnected from the Control Board Broken wire Faulty Control Board or Faulty Bill Validator VALIDATOR 7 will be displayed This Error cannot be cleared until the source of the problem is repaired If the VC1100 uses a Debit Card Reader without a Coin Changer or Bill Acceptor VALIDATOR 7 will always be present and cannot be cleared this is normal READER 8 If the Card Reader becomes disconnected from the Control Board i e Broken wire Faulty Control Board or Card Reader READER 8 will be displayed This Error cannot be cleared until the source of the problem is repaired If the VC1100 does not use a Debit Card Reader READER 8 will always be present and cannot be cleared this is normal DE720 Rev E 17 VC
72. owever following completion of the vend sequence the controller will pause for up to 3 seconds while it waits for detection of a product The controller will then handle the two possible cases as follows a For the product detection event the message PLEASE REMOVE PRODUCT will scroll repeatedly across the screen This message will continue to display as long as the sensor indicates the product is still blocking the optical beam b In the event that the product is not detected within 10 seconds the MAKE ALTERNATE SELECTION will appear once followed by a return to the display of available credit If the auto reinstate mode is not active for this particular selection then this product detection failure will also trigger the setting of a sold out state for the selection and cause the display of an error code 9 in the diagnostics menu If the auto reinstate mode is active for the particular selection then no sold condition will be applied to the failed selection and the controller will continue vend attempts on the particular selection if it s chosen again in the future This sold out status will be cleared when an open to closed transition of the door switch is detected or following an exit from the service mode In addition to a modified vending sequence a blocked optical beam during the non vending portion of the normal sales mode will cause the handling of credit acceptance and future vending to vary in the following 2 circumstances a If
73. play will show the particular selection followed by the price of the selection as a vend is attempted When the vend attempt has completed and the selection corresponded to a single selection or the last selection in a range of selections control will pass back to the selection display SELECT If for any reason a vend attempt on a particular motor fails then the controller will signal this by beeping 3 times If optical sensor is enabled the controller will wait for 3 seconds to verify product if no product was detected then the controller will beep three times before attempting the next selection in the sequence e During the process of test vending a range of selections the operator may press and hold the CANCEL button to cancel the process and return control to the selection display SELECT e successful test vend on a motor clears all errors associated with that selection DE720 Rev E 22 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING TEST RELAY WARNING The operator should be aware that operations of the functions within this menu have direct control over whatever device s is are connected to those lines With some devices such as compressors there is the potential for damaging the device with frequent toggling of this line This menu provides functions that allow the operator to test the operation of the refrigeration and defrost relays P
74. pressor from encountering overpressure situations due to opening and closing the door repetitively the controller will not re activate the refrigeration system for a period of 90 seconds from the initial opening of the glass door IDLE CONDITION The controller will monitor all present MDB peripherals for customer input while waiting for a keypad generated interruption If no action is taken then the programmable Point of Sales message will be scrolled on the display provided there are sufficient coins in the coin changer If an adequate quantity is not detected the PLEASE INSERT EXACT MONEY message will be displayed When credit has been established the amount of credit will be displayed otherwise the controller will continue as above until a vend sequence is initiated or a Coin Return request is made Ifa Coin Return request is received and the Force Vend feature is disabled the deposited credit will be returned in a like coin fashion COIN ACCEPTANCE The controller will allow acceptance of all coins as long as the accumulated credit is equal to or less than the maximum price of any selection in the current configuration When Multivend is active then this maximum value increases to 3 times the highest priced selection in the machine Coin acceptance will be disabled during all vends while coins are being paid out and while in the service mode of operation and if card reader credit is established FIRST BILL ACCEPTANCE Th
75. ressing the ENTER button after the user has navigated to the menu item labeled TES T RELAY will enter this menu Upon entry to the menu the display will read RELAY 1 By scrolling through the menu the operator may choose 2 additional relay functions RELAY 2 and RELAYS To enter any of these functions the operator should press the ENTER button Upon entry to the individual relay functions the display will change to reading or OFF where the indicates editing mode This initial ON OFF status indicates if the corresponding relay control in is active or inactive Pressing ENTER again will toggle the on off state At any time pressing the SAVE or CANCEL buttons will exit the function Upon exit from the function the state of the corresponding relay control line will revert to a state that is dependent on the controller s normal relay control algorithm RELAY 1 RELAY 1 is the Left Refrigeration Relay and is controlled by Sensor 1 located in the refrigerated compartment When Relay 1 is off relay 1 will be energized and the Compressor and Evaporator Fans will be off RELAY 2 RELAY 2 is the Right Refrigeration Relay and is controlled by Sensor 2 Relay 2 is not used on the VC1100 RELAY 3 RELAY 3 is the defrost relay When relay 3 is on relay 3 will be energized and the heaters will be on The Compressor and Evaporator Fans will be off DE720 Rev E 23 VC1100 For more information visit www Gumball com
76. rmation visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING gt DE720 Rev E Fo SET POINT This function allows the user to set an ideal operating temperature for the specific sensor This corresponds to the air temperature that the controller will attempt to maintain for this sensor while the sensor is activated Upon entry the display will read XXY where XX is the actual value and Y will be either C for degrees Celsius or F for degree Fahrenheit Pressing UP or DOWN will scroll the value of the temperature in the corresponding direction The maximum value is 70 F 21 C The minimum value is 30 F 34 C The temperature rolls over when the user scrolls through the maximum or minimum values At any point the modified value may be stored and this function exited by pressing SAVE Pressing CANCEL before pressing the SAVE button will exit this menu without storing the value DELTA This function allows the user to specify the temperature region around the set point that the refrigeration control will use to switch on and off The refrigeration Switch On point is equivalent to the set point plus the delta value divided by 2 The Switch Off point is the set point minus the delta value divided by 2 The value for delta is set in the same manner as the set point The maximum value is 20 F 11 C The minimum value is 5 F 3 C Example Ex
77. roller if the motor is not allowed to complete a full cycle or if after twelve seconds the motor has not yet returned to a home position the vend will be considered a failure A bad motor is defined as 1 A motor location requiring more than 12 seconds before detecting a home position signal 2 An electrically open motor circuit at the time the controller first attempts to vend the motor If a configured motor not in the autoreinstate range has been detected as being bad due to the detection of an open circuit that motor can not be vended until it is cleared by performing a successful free vend from within the service mode of operation When the optics mode is enabled and autoreinstate is inactive for the particular selection but the optical sensor detects no product In this case the controller will flag the item with a sold out error VMC 9 in addition to a long vend error VMC 2 The controller will also prevent further attempts to vend the particular selection until the selection s sold out error status is cleared DE720 Rev E 12 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING THE SERVICE MODE OF OPERATIONS To enter the Service Mode press the red button located on the controller board The controller automatically returns to the sales mode if no input from the keypad is received in approximately 25 seconds or if the button is pressed a second time within this period
78. scounting status between ON and OFF Pressing CANCEL will return control to the DAY field At any point pressing SAVE will store the current status and return control to the DAY field Note that presses of CANCEL will only force exit from this function while control is in the DAY field DE720 Rev E 42 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING RANGE This allows the operator to set the range of selections that will be affected when discounting is active Once in this menu item the user will see a display similar to SR ER 1 2 The user sets the first selection in the range by entering any letter from A through L followed by the number of the selection The last selection in the range is then set by entering any letter that is greater than or equal to the first row in the range A through L followed by the number of the selection If the letter of the last selection is equal to the letter of the first selection then the number of the last selection must be equal to or greater than the number of the first selection The software will not save a corresponding range that violates this rule Once the 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these buttons forces exit from this submenu and returns control to the previous menu level gt VALUE
79. settings the CANCEL button should be pressed gt Onoroff Upon entry into the AUTORE N S T menu the current on off state of auto reinstatement will be displayed as ON OFF A press of ENTER will change the display to ON or OFF where the indicates editing mode Pressing ENTER again will toggle the on off state At any time the on off state may be stored and this function exited by pressing SAVE RANGE Upon entry into the RANGE menu the display will show something similar to SR ER A J The user sets the first row in the range by selecting any letter from A through L The last row in the range may then be selected by entering any letter that is greater than or equal to the first row in the range A through L Once the 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these buttons forces exit from this submenu and returns control to the previous menu level DE720 Rev E 44 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING CAN BOTTLE ATTENTION This menu is disabled within the SERV CONT menu and must be restored into the Service Mode menu before attempting any settings See page 24 This submenu provides the operator with options for designating ranges of rows that will contain cans and or bottles Selections that are design
80. t L AVI3M 1531 lt 193135 lt 4 QN3A 1S31 lt 1531 lt 4 00000 INHO 12 3 lt 00000 lt 20 lt SNIOD 113 lt T4 lt 35 39510 A LNOAWd H lt A Mv310 lt 00000000 SGON3AJONVY lt 000 0000 HSVO 3ONVY lt N3 HS JONVY 135 lt 000 0000 lt SIIS lt 00000000 1NnOO 535 lt 000 0000 lt 531 6 s3 00000000 lt 1N002 151 lt 000 0000 S3WS 1SIH lt lt Q38f1913NOO lt 914 02 000 SYOLOW lt 1 02 lt YOLOW lt 0 34 lt SOIVQlIVA 339NVHO OWA SSONOVIG lt 3QON 5 1100 14 DE720 Rev t www Gumball com 800 260 0010 1 214 550 5079 VISI For more informat SECTION 5 PROGRAMMING DIAGNOSE The Diagnostics menu item displays the current status of the controller and peripherals Pressing ENTER after the user has navigated to the menu item labeled D AGNOSE starts this function Upon entry the status of the controller and each of the peripherals will be checked The order of checking is the Vending Machine Controller the Changer the bill Validator and the card reader The display will show in that order VMC CHANGER VALIDATOR and READER If no problems are encountered with the individual device then the name of the device will be followed by OK
81. t from this submenu and returns control to the previous menu level DE720 Rev E 46 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 WIRING DIAGRAMS VC1100 REFRIGERATION INTERFACE DIAGRAM SECTION 6 HOLIMS YOOd OIL3N9V SMS d S MOl138 STIVJ e N3HM 79 SIVNIWMS3L d SS lt S 109 N3HM GSLYOHS 9 79 SIVNIWH3L WOO ON ON ONS VC1100 d S4 3AO8V SN3dO HOLIMS 71 v gt NOES Ss 6 INM HOIIMS 1505 20 6 2 ANNOYS JvNOIS I 2 SEE amp 8 ed ONISNOH YOSNIS 9 pzseisd O 59 AVIS CD SALIH NONd3d 96149 LINN 9NISNJONOO 193135 061 v v8l c iw y v8l 6 oR 9 r 81 SI E FON on r u 8 Z 310N 335 X T 9 p NOVI 1504 30 L 310N 33S 4 981 a os xong 9 aay 300 MN3lv3H NOLVMOdVA3
82. ter of the selection followed by its number After entering the selection the SAVE button should be pressed The selection s location will be displayed along with a 5 digit price The desired price should then be entered using the numeric keys starting with the most significant digit followed by lesser significant digits Pressing SAVE will store the value and return to SELECT on the display e To set the price for a range of selections the user should enter the letter of the first row followed by the letter of the last row After entering the selections the SAVE button should be pressed A 5 digit price will appear the display The desired price should then be entered using the numeric keys starting with the most significant digit followed by lesser significant digits Pressing SAVE will store the value and return to SELECT on the display e Pressing the CANCEL button while S E LECT is displayed will return to the PRICE menu e Pressing the CANCEL button while 0 0 0 0 0 is displayed will return to the SELECT menu DE720 Rev E 25 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING OPTIONS This menu provides functions that allow the operator to control a variety of vending options Pressing the ENTER button after the user has navigated to the menu item labeled OPTIONS will enter this menu To exit this menu or any of the functions or submenus
83. the DISCOUNT menu the current On off State of discounting will be displayed as ON or OF F A press of ENTER will change the display ON or OFF where indicates editing mode Pressing ENTER again will toggle the on off state At any time the On off state may be stored and this function exited by pressing SAVE gt TIME This function allows the operator to program the start and stop times for discounting Upon entry into this submenu the display will show STRT hh mm new start time for this interval may be entered by pressing the numeric keys these will be displayed as they are entered The most significant digit followed by lesser significant digits It is not necessary to enter leading zeros and only the first four numbers will be used To save the new start time press SAVE The display will continue to 1 STOP hh mm A new stop time for this interval may be entered through the same method used for the start time When the stop time has been programmed the controller will return to the previous level in the menu structure and T ME will be displayed gt DAY This function allows the user to specify those days of the week in which discounting will apply Upon entry the display will read sun off or SUN Pressing UP or DOWN will scroll through the days of the week If ENTER is pressed control passes to the On off field for the corresponding day At this point presses of UP or DOWN will toggle the daily di
84. the optical sensor s range covers all configured selections within the matrix any additional credit acceptance and vending will be disabled b Ifthe optical sensor s range covers only a portion of the configured selections within the matrix vending will be disabled only for those selections within the optical range Configured selections outside of the range will still be available for vending attempts Onoroff Upon entry into the OPTIC menu the current on off state of the optical option will be displayed as ON or OF F A press of ENTER will change the display to ON or OFF where the indicates editing mode Pressing ENTER again will toggle the on off state At any time the on off state may be stored and this function exited by pressing SAVE or pressing CANCEL may restore the previously saved state RANGE This item allows the operator to specify those rows of products which are sensed for product delivery by the optical sensor Upon entry into this item the display will show something similar to SR ER A J The user sets the first row in the range by selecting any letter from A through L The last row in the range may then be selected by entering any letter that is greater than or equal to the first row in the range A through L Once the 2 letters in the range are entered the setting may be saved by pressing the SAVE button or canceled by pressing the CANCEL button Pressing either of these buttons forces exi
85. ting will revert to this maximum value To exit this mode before entering a value press CANCEL or exit the service mode DE720 Rev E 20 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING EXACT CHNG The Exact Change option forces the controller to display the message PLEASE INSERT EXACT MONEY ifa specified value of credit and every value in increments of the least coin tube value less than this value cannot be paid back Upon entry to this function a five digit number representing the exact change value appears A value of up to 5 digits may now be entered using the numeric keys This value may be saved at any time by pressing the SAVE key e When the highest vend price is greater than the unconditional acceptance value then the maximum settable value for exact change will be 3 times the highest vend price e When the highest vend price is less than the unconditional acceptance value then the maximum settable value for exact change is 3 times the unconditional acceptance value e Ifthe operator attempts to save a value that exceeds this amount a warning message will appear and the displayed setting will revert to this maximum value e The minimum value for exact change is the unconditional accept value If the operator attempts to save a value less than this amount a warning message will appear and the displayed setting will revert to this minimum value To exit this mode befor
86. ttons forces exit from this submenu and returns control to the shutdown menu level TEMPERTURE This menu allows the operator to activate and modify the controller s temperature control capabilities Pressing the ENTER button after the user has navigated to the menu item labeled TEMPERTURE accesses this submenu Pressing the ENTER button when any of the following functions or submenus is highlighted will pass control to that function or submenu To exit this menu or any of the functions within this menu without saving settings the CANCEL button should be pressed DEGREE F This function allows the operator to specify the units of measurement for displaying the temperature It s the first item reached upon entry to the temperature submenu The display will read either DEGREE F for Fahrenheit units or DEGREE for Celsius units Pressing ENTER will change the display to DEGREE or DEGREE C where the indicates an editing mode The units may now be toggle between C and F by pressing the ENTER button Pressing SAVE at any time will store the setting and exit editing mode gt SENSOR This submenu will allow the operator to control individual characteristics that are associated with SENSOR 1 Pressing the ENTER button after the user has navigated to the menu item labeled SENSOR will access that submenu gt SENSOR2 This menu should never be selected for use in a VC1100 DE720 Rev E 37 VC1100 For more info
87. u items are entered then the display will change to reading ON or OFF where the indicates editing mode This initial ON OFF status indicates if the corresponding service menu is currently active or inactive Pressing ENTER again will toggle the on off state At any time the state may be stored and this function exited by pressing SAVE Ifthe CANCEL button is pressed then the function will not modify the status of the specific service mode menu DE720 Rev E 24 VC1100 For more information visit www Gumball com 800 260 0010 1 214 550 5079 SECTION 5 PROGRAMMING PRICE This menu provides functions that allow the operator to assign prices to individual selections over a range of selections or to a combination of selections Pressing the ENTER button after the user has navigated to the menu item labeled PR C E will enter this menu To exit this menu or any of the functions within this menu the CANCEL button should be pressed Pressing the ENTER button when any of the following functions are highlighted will pass control to that function Note that the maximum price that can be set in all of the following cases is 199 99 for a scale factor of 1 and 999 95 for a scale factor of 5 gt ITEM S Pressing the ENTER button after the user has navigated to the menu item labeled TEM S will enter this menu Upon entry the display will read SELECT e To set the price of a single selection the user should enter the let
88. within this menu the CANCEL button should be pressed Pressing the ENTER button when any of the following functions are highlighted will pass control to that function gt BILL SCROW This option will allow the last bill accepted to be returned provided the bill acceptor is capable of such a feature Upon entering this function the display will show the current on off state as On or OFF Pressing ENTER again will toggle the on off state Pressing SAVE will store the setting and exit the menu Pressing CANCEL will exit the menu without modifying the setting gt FORCE VEND This option will force the customer to complete a purchase once they have deposited money of any form If a vend is attempted on a configured selection and the motor fails during this vend the credit will be placed in escrow and the customer would be allowed a credit return in a like coin fashion regardless of the force vend status Upon entering this function the display will show the current on off state as On or OFF Pressing ENTER again will toggle the on off state Pressing SAVE will store the setting and exit the function Pressing CANCEL will exit the function without modifying the setting MAX CHANGE This option will prevent change from being returned to the customer until the credit amount is less than or equal to the programmed maximum change limit Upon entering this submenu the display will show the current On Off Stat

OPERATION & SERVICE MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents

OPERATION &amp; SERVICE MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents

OPERATION & SERVICE MANUAL