SERVICE MANUAL - Appliance Factory Parts
Contents
1. 42 1 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or loss of life IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the washer follow basic precautions including the following e Read all instructions before using the washer e Before the washer is removed from service or Do not wash articles that have been previously discarded remove the door to prevent children cleaned in washed in soaked in or spotted with from hiding inside gasoline dry cleaning solvents or other e Do not install or store the washer where it will be flammable or explosive substances as they give exposed to the weather e Do not add gasoline dry cleaning solvents Do not repair or replace any part of the washer or other flammable or explosive substances to the attempt any servicing unless specifically wash water These substances give off vapors that recommended in the user maintenance could ignite or explode instructions or published user repair instructions e Under certain conditions hydrogen gas may be that you understand and have the skills to carry produced in a hot water system that has not been out used fo2. LG WASHING MACHINE SERVICE MANUAL CAUTION READ THIS MANUAL CAREFULLY TO DIAGNOSE PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT MODEL GCW1069QS GCW1069CS MARCH 2010 PRINTED IN KOREA P No MFL30599165 CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS 3 2 0110m19 5960 S E E E 4 FEATURES AND TECHNICAL EXPLANATION ca eeaaiiieaoetaaaiassei BRP INT EI FIN na C c CC c 7 Da INSTALLATION INSTRUC 8 G OPERA TON 14 16 7 WIRING DIAGRAM PROGRAM CHART 17 TROUBLE SROOTIN G 12222222 ca 5S 18 20 8 1 BEFORE PERFORMING ne 18 8 2 TEST Bass eet 0 can 18 8 3 HOW TO CHECK THE WATER LEVEL FREQUENCY 18 8 4 HOW CHECK THE RPM C S 18 ERROR DIOPLA Y eirp eee ee eee eee 19 20 6 0 DISPEN ER Gee ce eee ee eee E E E 21 9 DIAGNOSIS AND TROUBLESHOOTING 22 29 10 DISASSEMBLY CC TC l1 30 38 EXPLODED VIE c ca peat een aes foe eaten adden ne nent 39 11 1 1 CABINET 8 CONTROL PANEL ASSEMBLY COIN TYPE 39 11 1 2 CABINET 8 CONTROL PANEL ASSEMBLY CARD TYPE 40 T2 EUV ec TUB FAS SEY 41
3. 3 minutes of washing time and an extra rinse 16 7 WIRING DIAGRAM PROGRAM CHART Card GCW1069QD GCW1069QS Coin GCW1069CD GCW1069CS ESDS DISPLAY PWB WH PME MAIN PWB 23 1 2 3 4 5 6 78 1321411 4 65 6 7 8 NE BK ro fev A HA BLlRp a BLIBK Goss 2131415161718 HHH willa 1 59 T HI P Coin Drop VCC NA 3 30 mi rd Rea 2 ption 181716154 3 2 1 2 3 1 THERMISTOR PRESSURE SWITCH ee ee lt lt NOTE gt 250 TERMINAL 250 TERMINAL HOUSING n n PIN CONNECTOR RING TERMINAL GROUND DRAIN PUMP CIRCULATION PUMP DOOR LOCK SWITCH Program Chart NORME a ie owe ool Se 1 2 EJ gt 7 1 W 2 18 1 2 A m 5 5 Oooo WHITES ef lel cell ebb e T po Approx Working Time min 9 15 WASH RINSE SPIN 9min 15min 13min 2 33 _ 180 x m ess TT TT 4 14 l 5n s gt time is in minutes Water Supply W S Intermittent Spin 1 S Disentangle D T 17 8 TROUBLESHOOTING 8 1 BEFORE PERFORMING SERVICE Be careful of electri
4. 5 INSTALLATION INSTRUCTIONS A WARNING e Washer is heavy Two or more people may be needed to install and move the appliance Failure to do so can result in back or other injury e Store and install the washer where it will not be exposed to temperatures below freezing or exposed to outdoor weather conditions Failure to follow this warning can cause serious injury fire electrical shock or death e This appliance must be properly grounded for personal safety Properly ground washer to conform with all governing codes and ordinances Failure to follow this warning can cause serious injury fire electrical shock or death e Do not install the washer in humid spaces to reduce the risk of electric shock Failure to follow this warning can cause serious injury fire electrical shock or death e The base opening must not be obstructed by carpeting when the washer is installed on a carpeted floor e Do not remove ground prong Do not use an adapter or extension cord Plug into a grounded 3 prong outlet Failure to follow this warning can cause serious injury fire electrical shock or death Keep the area underneath and around your appliances free of combustible materials such as lint paper rags chemicals etc Failure to do so can result in fire To reduce the risk of personal injury adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses Failure to follow all of th
5. Disconnection of Card Reader Wire 8 6 DISPENSER The dispenser drawer is a multi chambered reservoir that allows the user to add all the appropriate laundry additives before starting the cycle It has a place for pre wash and Main wash detergent fabric softener and bleach Powdered or liquid detergents may be used but softener and bleach must be liquids Detergents should carry the HE designation Do not use regular detergents in the washer or overusing will occur Regular detergents also cause a scum build up in the tub which leads to poor performance and a foul odor 1 HOT INPUT 2 MAIN WASH 3 BLEACH 4 SOFTRNER 1 1 21 9 DIAGNOSIS AND TROUBLESHOOTING AWARNING 1 Be careful of electric shock if disconnecting parts while troubleshooting 2 First check the connection of each electrical terminal with the wiring diagram 3 If you replace the MAIN PWB ASSEMBLY reinsert the connectors correctly NO POWER Check the fuse or reset 2 15 the supplied voltage 120 the circuit breaker Is the voltage between the FILTER ASSEMBLY connectors 120 AC Replace the FILTER ASSEMBLY CIRC Replace MAIN PWB Is the LED lam on ASSEMBLY Are the connectors on the PWB loose Reconnect 15 wire of the DISPLAY PWB ASSEMBLY Replace the CABLE broken HARNESS PWB ASSEMBLE DISPLAY Replace DISPL
6. VALVE ASSEMBLY Make sure the tap is closed before replacing Is water continuously supplied Replace the PRESSURE S W ASSEMBLY Is PRESSURE S W ASSEMBLY broken Check electrical connection Replace the MAIN PWB ASSEMBLY Is displayed Replace the PRESSURE S W ASSEMBLY Is PRESSURE S W ASSEMBLY broken NO Check electrical connection Replace the MAIN PWB ASSEMBLY dE ERROR DOOR ERROR Is displayed Started with door opened Was the load too large Avoid overloading Check the DOOR SWITCH ASSEMBLY Connector and MAIN PWB ASSEMBLY Blue 4 pin Yellow 4 pin and white 3 pin fconnector Clicking sound is heard once or twice when the START button is pressed to start the cycle NO ls DOOR SWITCH ASSEMBLY broken Replace the DOOR SWITCH ASSEMBLY Does the spring of Latch Hook actuate Replace Door Assembly Latch Hook 26 VIBRATION amp NOISE IN SPIN Have all the transit bolts and base packing been removed Remove the transit bolts and Base packing Is the washer installed on a solidly constructed floor Move the washer or reinforce the floor Check if the washer is perfectly level as follows Check the leveling of the washer with a level and check that the washer is stable Put an unbalance part rubber inside of drum and start QC test mode and run in high spin Refer to p
7. closed in a door or walked upon Pay particular attention to plugs wall outlets and the point where the cord exits the appliance Connecting the water supply hoses e Water supply pressure must be between 14 5 and 116 psi 100 800 kPa Do not crossthread when connecting the inlet hose to the valve Cold Hot e If the water supply pressure is more than 116 PSI a pressure reducing device should be installed e Two sealing washers are supplied with the water inlet hoses to prevent water leaks Check for leakage of washing machine connections by turning the tap completely on Periodically check the condition of the hose and replace the hose if necessary e Make sure that there is no kink in the hose and that it is not crushed e Be sure that the two water input ports are connected to the correct water faucets The connector for hot water 15 colored red the cold 15 blue Sealing washer NOTE Use new hoses when installing a washing machine Replace them periodically Old hoses should not be used Do not install your washing machine in a room where temperatures below freezing may occur Frozen hoses may burst under pressure The reliability of the electronic control unit may be impaired at temperatures below the freezing point If the appliance is delivered in the winter months and temperatures are below freezing store the washing machine at room temperature for a few hours before putting it into
8. machine top plate diagonally the machine should not move up and down at all Please check both directions 17 Electrical connection e Do not use an extension or double adapter e If the supply cord is damaged it must be replaced by a qualified person in order to avoid a hazard e If the machine will not be used for an extended time unplug it shut off the water supply and open the door to provide ventilation e Connect the machine to a grounded outlet in accordance with current wiring regulations The appliance must be positioned so that the plug is easily accessible WARNING Concerning the power cord Most appliances recommend they be placed upon a dedicated circuit that is a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits Check the specification page of this owner s manual to be certain Do not overload wall outlets Overloaded wall outlets loose or damaged wall outlets extension cords frayed power cords or damaged or cracked wire insulation are dangerous Any of these conditions could result in electric shock or fire Periodically examine the cord of your appliance and if its appearance indicates damage or deterioration unplug it discontinue use of the appliance and have the cord replaced with an exact replacement part by an authorized servicer Protect the power cord from physical or mechanical abuse such as being twisted kinked pinched
9. proper outlet consult an electrician WARNING Improper connection of the equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it does not fit the outlet have a proper outlet installed by a qualified electrician 3 2 SPECIFICATIONS MODEL GCW1069QD GCW1069GS GCW1069CD GCW1069CS COLOR BLUE WHITE POWER SUPPLY 120V 60 Hz PRODUCT WEIGHT 190 Ibs 86 kg ELECTRIC POWER WASHING 155 W CONSUMTION DRAIN MOTOR 80 W WASH 45 rom REVOLUTION SPEED SPIN 1150RPM CYCLES OPTIONS ADD SUPER WASH Cycle OPERATIONAL WATER PRESSURE 14 5 116 psi 100 800 kPa CONTROL TYPE Electronic WASH CAPACITY ft 4 2 EC 3 64 DIMENSIONS 27 W X 30 3 e D X 38 1 4a H X 50 19 46 D door open DOOR SWITCH TYPE PTC Solenoid WATER LEVEL 10 steps by sensor LAUNDRY LOAD SENSING Incorporated ERROR DIAGNOSIS Incorporated 3 FEATURES amp TECHNICAL EXPLANATION 3 1 FEATURES Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley The Tilted Drum and Extra Large Door Opening Tilted drum and extra large door opening make it possible to load and unload easily Ultra Capacity The larger drum enables not just higher head drop and stronger centrifugal force but also less tang
10. AY PWB ASSEMBLY or repair wire 22 Is the tap opened Is the tap frozen Is the water supply shut off Is filter in the inlet valve clogged with foreign material Is resistance between each terminal of the INLET VALVE ASSEMBLY 0 8 1 2 Verify the voltage of the inlet valve connector is 120 V AC Refer to page 18 TEST MODE 23 IE ERROR NO WATER SUPPLY Is displayed After separating the hose from the washing machine soak in hot water for 10 minutes Clean the filter of INLET VALVE ASSEMBLY Replace the INLET VALVE ASSEMBLY x Make sure the tap is closed before replacing Check electrical connection Replace the MAIN PWB ASSEMBLY OE ERROR DRAIN TROUBLE Is displayed 15 the drain hose twisted or frozen Repair the DRAIN HOSE ASSEMBLY Clean the filter 5 the drain pump filter clogged with foreign material such as pins coins etc Reconnect or repair the connector 15 the connector disconnected or disassembled Is the coil of the drain pump too high or low resistance of the coil is 10 20 02 Replace the DRAIN PUMP ASSEMBLY When checking voltage between connectors and during drain is the voltage 220 AC as in the figure 2 Replace the PWB ASSEMBLY 24 FE ERROR Is displayed Is resistance between each terminal of INLET VALVE ASSEMBLY 0 8 1 2kQ Replace the INLET
11. age 17 When the machine 15 spinning in high speed verify that it is stable If you do not have the unbalance part put 4 5 to 6 5 lbs 2 to 3 kg of clothing When the machine is spinning at high speed verify that it is stable If it is not stable adjust feet accordingly After the washer is level tighten the lock nuts up against of the base of the washer All lock nuts must be tightened Adjustable feet Adjustable feet 2 DETERGENT SOFTENER BLEACH DOES NOT FLOW IN Refer to page 22 IE ERROR Is water supplied Are the plugs correctly connected to the terminals of the INLET VALVE ASSEMBLY YES Check the wiring Put it in the correct compartment wash Compartment Liquid chlorine Bleach Compartment Q Liquid fabric Softener Compartment Is detergent softener bleach put in the correct compartment of the DRAWER Clean the CAP and DRAWER Is the detergent softener bleach CAP clogged 15 the motor bolt loose Secure the bolt Replace the STATOR Is there friction noise coming from the motor ASSEMBLY or ROTOR ASSEMBLY 28 SUDS OVERFLOW FROM THE APPLIANCE Is HE High Efficiency detergent used 5 the proper amount of detergent used as recommended Recommend to reduce the amount of detergent This appliance has an automatic suds sensing function which prevents overflow When exc
12. c shock when disconnecting parts while troubleshooting The voltage of each terminal is 120V when the unit is plugged in 8 2 QC TEST MODE The washer must be empty Card Type 1 Insert Service Card 2 Display 3 Press the Start button repeatedly to cycle through the test modes Coin Type 1 Turn on off toggle switch 2 Display 3 Press the Start button repeatedly to cycle through the test modes Number of times the START button is pressed Check Point Display pe TH None Turns on all lamps and locks the door Displayed gc XX and US alternately Version 3 times rpm 600 rpm 1000 1100 Water level frequency 261 _ l6ims 7 8 3 HOW TO CHECK THE WATER LEVEL FREQUENCY Press and hold the ADD SUPER WASH and PERMANENT PRESS buttons simultaneously Pom When you check the water level the first digit is a 0 which means 2 A display indicating 041 is a water level frequency of 241 multiplied by 0 1 KHz for an actual frequency of 24 1 KHz 8 4 HOW TO CHECK THE RPM Press the ADD SUPER WASH AND WHITES button simultaneously Under 200 rpm The display indicates the rom Under 200 rpm Over 200 rpm The display indicates the rom x 10 rpm So for example a display indicating 050 rom of 050 x 10 rom 500rpm 18 8 5 ERROR DISPLAY e f you press the START button when an error is displayed any error except will disappear and the machine will go i
13. crew a screw on PRESSURE SWITCH ASSEMBLY 4 Remove all wire from hooks 5 Remove the Protective Cover 6 Disconnect the connectors 7 Unscrew 1 screw on the back 8 Disassemble the MAIN PWB ASSEMBLY DISPENSER ASSEMBLY DISPENSER ASSEMBLY INLET VALVE ASSEMBLY 33 1 Disassemble the CONTROL PANEL ASSEMBLY refer to page 30 2 Disassemble the TOP PLATE ASSEMBLY refer to page 31 3 Disassemble the clamps and hoses 4 Disassemble the bellows at the lower side of DISPENSER 1 Disassemble the CONTROL PANEL ASSEMBLY refer to page 30 2 Disassemble the TOP PLATE ASSEMBLY refer to page 31 3 Disassemble the 4 connectors from the VALVES 4 Disassemble the clamps and hoses 5 Unscrew the 2 screws in the back Connector Color 1 Blue Housing OR Bk 2 White Housing WH Bk 3 Blue Housing GY Bk Red Housing BL Bk CABINET COVER 1 Disassemble the CONTROL PANEL ASSEMBLY refer to page 30 2 Open the DOOR 3 Disassemble the CLAMP ASSEMBLY 4 Unscrew the 5 screws from the CABINET COVER 5 Unscrew the screw from CAP COVER 6 Unscrew the screw from inside CAP COVER CAP COVER 7 Put a flat screwdriver or putty knife into both sides of the CAP COVER and pull it out 34 8 Unscrew the screw from the lower side of the CABINET COVER 9 Tilt the CABINET COVER 10 Disconnect the DOOR S W connector NOTE When assembl
14. e safety warnings in this manual could result in property damage personal injury or death fi Shipping bolts The appliance is fitted with shipping bolts to prevent internal damage during transportation Packing and all shipping bolts must be removed before using the washer Packing Support When unpacking the base be sure to remove the additional packing support in the middle of the base packing m Removing shipping bolts Unscrew the 4 bolts with the wrench supplied Close the holes with the caps supplied Take out the 4 bolts by twisting the braces slightly Keep the 4 bolts and the wrench for future use Whenever the appliance is transported the shipping bolts and braces must be replaced 8 Installation clearances The location must be large enough to open the washer door completely Washer dimensions 3811 46 98 3 cm Minimum installation spacing for recessed area installation 75 6 10 cm Side view 27 2 5 68 6 Front view The following dimensions shown are for the minimum spacing allowed Additional spacing should be considered for installation and servicing Additional clearances might be required for wall door and floor moldings Additional spacing of 4 10 cm on back 1 2 5 cm o
15. essive suds are sensed the suds removing implementations such as drain water input and pause will operate without rotating the drum 1 4 Cup Recommended 29 10 DISASSEMBLY INSTRUCTIONS Be sure to unplug the machine before disassembling and repairing the parts CONTROL PANEL ASSEMBLY AZ CONTROL PANEL ASSEMBLY NTROL PANEL EMBLY DISPLAY PWB ASSEMBLY 1 Pull out the DRAWER Do not pull out the DRAWER too forcefully as it can be broken 2 Unscrew 3 screws 3 Disassemble the CONTROL PANEL ASSEMBLY Pull out the CONTROL PANEL Do not pull out the CONTROL PANEL too forcefully as it can be broken 4 Disconnect the DISPLAY PWB ASSEMBLY connector from CABLE HARNESS Disassemble the CONTROL PANEL ASSEMBLY 2 Unscrew the 4 screws from the CONTROL PANEL ASSEMBLY 3 Disassemble the DISPLAY PWB ASSEMBLY 30 TOP PLATE ASSEMBLY 31 A WARNING When you disassemble the top plate be sure to take gloves and careful plate s edge Failure to do so can Cause serious injury 1 Disassemble the CONTROL PANEL ASSEMBLY refer to page 30 2 Remove 2 screws on the CONTROL PANELframe 3 Push the TOP PLATE backward forcefully 4 Lift the TOP PLATE MAIN PWB ASSEMBLY 32 1 Disassemble the CONTROL PANEL ASSEMBLY refer to page 30 2 Disassemble the TOP PLATE ASSEMBLY refer to page 31 3 Uns
16. he TOP BRACKET MOTOR ASSEMBLY 1 Disassemble the BACK COVER 2 Remove the bolt 3 Pull out the ROTOR 4 Unscrew the 2 screws from the tub bracket 5 Remove the 6 bolts on the stator 6 Unplug the 2 connectors from the STATOR DAMPER 1 Disassemble the CABINET COVER or BACK COVER DAMPER 2 Disassemble the damper hinges from the tub HINGE DAMPER and base 3 Separate the dampers NOTE Do not re use an old damper pin Always replace it with a new one 38 11 EXPLODED VIEW COIN TYPE 11 1 1 CABINET amp CONTROL PANEL ASSEMBLY 11 1 2 CABINET amp CONTROL PANEL ASSEMBLY CARD TYPE 40 11 2 DRUM amp TUB ASSEMBLY 11 3 DISPENSER ASSEMBLY
17. hildren to operate and play in or around the machines COIN TYPE SIDE BY SIDE GCW1069QS PROCESSING 2 54 WASH RINSE SPIN DELICATES DOOR LOCK PERM PRESS WASHER SAFETY RULES UE REDISTRIBUTE LOAD PRESS START 1 Do not open the door until the cycle has completed the door lock light shuts off and the rotating drum has come to a stop 2 Do not wash articles that are flammable contain flammable fume or dye products 3 Do not tamper with the door safety switch or door lock 4 Do not attempt to open the door or place hands into the washer to remove or add clothes during operation 5 Do not allow children to operate and play in or around the machines 1 DISPLAY LED 3 START BUTTON 2 CYCLE BUTTON 4 STATUS BUTTON 14 STATUS LED PROCESSING 2 gt gt 16 WASH RINSE SPIN WASHER SAFETY RULES DISPLAY LED CYCLE BUTTON I J DOOR LOCK UE REDISTRIBUTE LOAD PRESS START 1 Do not open the door until the cycle has completed the door lock light shuts off and the rotating drum has come to a stop 2 Do not wash articles that are flammable contain flammable fume or dye products 3 Do not tamper with the door safety switch or door lock 4 Do not attempt to open the door or place hands into the washer to remove or add clothes during operation 5 Do not allow children to operate and play in or around the machines 1 Display LED The display shows
18. ing the CABINET COVER connect the connector 11 Lift and separate the CABINET COVER 1 Disassemble the CABINET COVER refer to page 34 2 Disassemble the CLAMP ASSEMBLY Ji TUB GASKET CLAMP 3 Disassemble the GASKET 35 DOOR ASSEMBLY 1 Open the DOOR 2 Unscrew the 7 screws from the HINGE COVER Put a flat screwdriver into the openng of the hinge and pull out the HINGE COVER 4 Unscrew a screw from the lower side of DOOR 5 Lift door and remove Be careful The door is heavy 1 Open the DOOR and disassemble the CLAMP ASSEMBLY 2 Unscrew the 2 screws 3 Remove connector from DOOR S W ASSEMBLY NOTE DOOR SWITCH e Reconnect the connector after replacing the ASSEMBLY DOOR SWITCH ASSEMBLY CLAMP ASSEMBLY 36 PUMP ASSEMBLY NOISE FILTER NOISE FILTER 37 1 Disassemble the CABINET COVER refer to page 34 2 Separate the PUMP HOSE and the BELLOWS from the PUMP ASSEMBLY 3 Unscrew 2 screws 4 Remove the PUMP ASSEMBLY in arrow direction 1 Disassemble the CABINET COVER refer to page 34 2 Unplug the white connector from the THERMISTOR 3 Pull it out by holding the bracket of the THERMISTOR 1 Disassemble the CONTROL PANEL ASSEMBLY refer to page 30 2 Disassemble the TOP PLATE ASSEMBLY refer to page 31 3 Disassemble two or three connectors from the NOISE FILTER 4 Unscrew a screw from t
19. ling and wrinkling of the laundry Heavier loads such as king size comforters blankets and curtains can be washed Large Door and Window The large window lets you see the wash as it progresses The Stainless Steel drum Stainless Steel Drum doesn t rust Automatic Wash Load Detection Automatically detects the load and optimizes the washing time 3 2 WATER LEVEL CONTROL This model incorporates a pressure sensor which can sense the water level in the tub The water supply is stopped when the water level reaches the preset level then the selected cycle begins Spinning does not proceed until the water in the tub drains to a certain level 3 3 DOOR CONTROL The door can be opened by pulling the door handle whenever washer is not in operation When the cycle is completed the DOOR LOCKED light will turn off l a power failure has occurred while in operation the door will unlock after 2 minutes Clicking sounds can be heard when the door is locked unlocked 3 4 THE DOOR CAN NOT BE OPENED While program is operating While Door Lock lights turn on While the drum is rotating 3 5 DOOR LOCKED LAMP LIGHTS When the frequency of water level is lower than 22 9 kHz It can be canceled when the frequency is more than 23 8 kHz When the temperature inside the tub is higher than 45 C 104 F and water level is not 25 5 kHz It can be canceled when the water level is 25 5 kHz or the tempe
20. n Install the appliance on a solid and level floor surface preferably in a corner of the room If the floor is uneven adjust the adjustable feet as required Do not insert pieces of wood etc under the feet NOTE Extend the feet no more than necessary to level the washer The more the feet are extended the more the washer will vibrate Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level Use a level e After the washer is level tighten the lock nuts up against of the base of the washer All lock nuts must be tightened It is critical to adjust the feet perfectly This must be done while the washer is spinning with a load Use the wrench supplied to adjust the feet until there is no vibration Then tighten the lock nuts to prevent further adjustment Lock nut NOTE If there is vibration and noise during the spin cycle re check the leveling of the washer adjust the feet as required and tighten the lock nuts securely to prevent changes in adjustment Run the washer with a test load to make certain your washer is properly leveled Put an unbalance weight part in the machine You can check noise and or vibration on high speed spin rpm through the QC test mode refer to page 18 When the machine spins at high speed verify that it is stable If not adjust the feet accordingly Diagonal Check When pushing down the edges of the washing
21. n all sides of the washer is recommended to reduce noise transfer Companion appliance spacing should also be considered INSTALL THE APPLIANCE ON A FLAT AND FIRM SURFACE solid floor Level floor Allowable slope under entire washer is 1 e To minimize noise and vibration the washer MUST be installed on a solidly constructed floor e Carpeting and soft tile surfaces are not recommended e Never install the washer a platform or weakly supported structure CONNECT POWER PLUG Connect the power plug to the wall outlet Must be within 60 1 5 of either side of the washer Do not overload the outlet with more than one appliance Time delay fuse or circuit breaker is recommended 10 NOTE A firm solid floor is even more critical to a front loading washer than to a top loader If your floor is wood and or frame construction you may need to reinforce it Front loaders use substantially faster spin speeds than top loaders causing greater vibration If the floor is not solid your washer will vibrate You will hear and feel the vibration throughout your house Avoid connecting several electric devices as doing so may cause a fire NOTE It is the personal responsibility and obligation of the customer to have a proper outlet installed by a qualified electrician Level adjustment Leveling the washing machine properly prevents excessive noise and vibratio
22. nto the pause status ERROR SYMPTOM CAUSE Correct water level 246 is not reached within 10 minutes after water is supplied or it does not reach the preset water level within 12 minutes WATER INLET ERROR The load is too small IMBALANCE The appliance is tilted ERROR Laundry is gathered to one side e Non distributable things are put into the drum Not fully drained within minutes Water is overflowing water level frequency is over 213 x If is displayed the drain pump will operate to drain the water automatically OVER FLOW PRESSURE SENSOR The SENSOR SWITCH ASSEMBLY is out of order Door not all the way closed DOOR OPEN Loose electrical connections at door switch and PWB Assembly The DOOR SWITCH ASSEMBLY is out of order 19 SYMPTOM LOCKED MOTOR ERROR EEPROM ERROR CARD READER ERRER The connector 3 pin male white in the MOTOR HARNESS is not connected to the connector 3 pin female white of STATOR ASSEMBLY e The electric contact between the connectors 3 pin male white in the MOTOR HARNESS and 4 pin female white connector in the MAIN PWB ASSEMBLY is bad or unstable e The MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut open circuit The hall sensor is out of order defective e EEPROM is out of order Displayed only when the START button is first pressed in the QC Test Mode e
23. operation 12 Installation of drain hose about 78 about 45 The drain hose should not be placed higher than Properly securing the drain hose will protect the 96 in from the bottom of the washer floor from damage due to water leakage Laundry tub ax 96 2 4 m When installing the drain hose at a sink secure it so it cannot break away and cause flooding and damage e Place the end of the drain hose in the hole of the e Properly securing the drain hose will protect the floor drain system floor from damage due to water leakage Make sure that the hose is not twisted Avoid submerging the end of the hose 6 OPERATION CARD TYPE SIDE BY SIDE GCW1069CS PROCESSING 1 LOAD MACHINE 2 CLOSE DOOR we Y R 3 INSERT CARD 4 SELECT CYCLE 5 PRESS START WASH RINSE SPIN DELICATES 6 WAIT FOR TONE DOOR LOCK PERM PRESS WASHER SAFETY RULES UE REDISTRIBUTE LOAD PRESS START 1 Do not open the door until the cycle has completed the door lock light shuts off and the rotating drum has come to a stop 2 Do not wash articles that are flammable contain flammable fume or dye products 3 Do not tamper with the door safety switch or door lock 4 Do not attempt to open the door or place hands into the washer to remove or add clothes during operation 5 Do not allow c
24. r 2 weeks or more HYDROGEN GAS IS e See Installation Instructions for grounding used for such a period before using the washing machine turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas As gas Do not place items exposed to cooking oil in your is flammable do not smoke or use an open flame washer Items contaminated with cooking oils may during this time contribute to a chemical reaction that could cause a load to catch fire e ALWAYS follow the fabric care instructions supplied by the garment manufacturer e Do not allow children to play on or in the washer Close supervision of children is necessary when Do not use fabric softeners or products to the washer is used near children eliminate static unless recommended by the manufacturer of the fabric softener or product SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances e Do not use an adapter or extension cord e Do not remove ground prong e If you don t have the
25. rature inside tub is lower than 40 118 F 4 PARTS IDENTIFICATION Shipping Bolts 4 Power Plug lf the supply cord is damaged it must be replaced by the manufacturer or an authorized service technician in order to avoid a hazard Control Panel Drain Hose Water Circulation HH HH HH HH HH ee HH HH BH HH BH BH HH HH HH HH HH BH HH HH Back of Washer Cold Water Inlet Dispenser p Drum Door Air Vent for Safety Hot Water Inlet Lower Cover Cap Adjustable Feet eee eee Drain Plug Drain Pump Filter Name Front loading Washing Machine Power supply 120V 60Hz Size 686 mm W X 767 mm D X 982 mm H 129 1 cm D with door open 27 X 2934 X 3811 4 6 H 5019 46 with door open Weight 190 Ibs 86 kg Wash capacity 3 63 cu ft IEC 4 2 cu ft Spin speed 1150 rom max Permissible water pressure 14 5 116 psi 100 800 kPa Specifications subject to change by manufacturer Accessories LES fum Tie strap Hot Cold 1each Wrench to secure drain hose to standpipe Hose inlet hose or laundry tub
26. the vend price and remaining time and programming options Error codes are also displayed here 2 CYCLE BUTTON Press the CYCLE button to select the desired cycle based on laundry types and conditions WHITES Use for hot washing for heavy fabrics such as white clothes table linens and heavily soiled clothes COLORS Use for warm washing for heavy fabrics such as jeans corduroys or work clothes DELICATES Use for cold washing for synthetic fabrics such as washable knit fabric and no iron finishes PERMANENT PRESS Use for warm washing for sturdy fabrics such as work casual work 15 START BUTTON B START BUTTON The START LED flashes when the full vend price has been satisfied and the cycle has been chosen 4 STATUS LED LED flashes whenever the washing aS wasn Cycle is in operation LED flashes whenever the Rinsing rinse CYCle is in operation 16 LED flashes whenever the Spining cycle is in operation O O poor tock LED flashes whenever the door lock is activated Select cycles designed for different types of fabric and soil levels Wash Rinse Spin Add Super Whites Cotton Linen Towels Shirts Hot Cold High Sheets Mixed Loads Work Clothes Warm Cold High Jeans Shirts Dress Shirts Blouses Dress Shirts Pants Wrinkle Perm Press Free Clothing Poly Cotton Warm Cold Medium Blend Clothing Tablecloths Add super wash Adds an additional
Download Pdf Manuals
Related Search