FlexPointTM DC Converter FlexPointTM DC Converter
Contents
1. WARNING REGARDING EARTHING GROUND a This equipment shall be connected to the DC supply system earthing electrode conductor or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing electrode is connected b This equipment shall be located in the same immediate area such as adjacent cabinets as any other equipment that has a connection between the earthed conductor of the same DC supply circuit and the earthing conductor and also the point of earthing of the DC system The DC system shall not be earthed elsewhere c The DC supply source is to be located within the same premises as this equipment d There shall be no switching or disconnecting devices in the earthed circuit conductor between the DC source and the earthing electrode conductor Cabling and Power Up 1 Securely attach the FlexPoint DC Converter to a FlexPoint media converter using 4 phillips head screws refer to illustration 2 If desired attach the optional wall mounting brackets part number 4381 and securely fasten to desired location refer to illustration Assure that the DC circuit breaker can supply 1 0A of current to the power supply 4 Locate the DC circuit breaker and switch the DC circuit breaker to the OFF position Cut the power cable to the length required Strip approximately 3 8 of an inch of insulation from the power cable wires Connect the power cables to the Fle2. lt gt Black Box Corporation The World s Source for Cabling and Network Connectivity FlexPoint DC Converter CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT outside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com gt Black Box Corporation The World s Source for Cabling and Network Connectivity FlexPoint DC Converter CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT outside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com General Description Designed for telecommunications environments such as campuses and phone centers that use DC power as a primary source The FlexPoint DC converter provides a user with the ability to power a single media converter with DC power Site Preparation Requirements 1 Power Assure the DC power can supply 1 0A of current 2 This equipment requires 18 60 VDC 1 0 Amps of power Appropriate overloading protection should be provided on all DC power source outlets utilized 3 Wiring methods used for the connec
3. TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A pre
4. cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada 040 01017 001 01 01 01 Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante En caso de existir una antena externa deber ser localizada lejos de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un ca
5. UNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada
6. ance with the Site Preparation Requirements outlined earlier in this document gt S gt A e e e Te Cabling and Power Up 1 Securely attach the FlexPoint DC Converter to a FlexPoint media converter using 4 phillips head screws refer to illustration 2 If desired attach the optional wall mounting brackets part number 4381 and securely fasten to desired location refer to illustration 3 Assure that the DC circuit breaker can supply 1 0A of current to the power supply 4 Locate the DC circuit breaker and switch the DC circuit breaker to the OFF position 5 Cut the power cable to the length required 6 Strip approximately 3 8 of an inch of insulation from the power cable wires 7 Connect the power cables to the FlexPoint DC Converter by fastening the stripped ends to the DC connector 8 Connect the power cables to the circuit breaker and switch the circuit breaker ON 9 Check the power LED on the back panel of the FlexPoint DC Converter The LED should be ON 10 Check the power LED on the front pannel of the attached FlexPoint Media Converter The LED should be ON Copyright 2001 Black Box Corporation All rights reserved 1000 Park Drive e Lawrence PA 15055 1018 724 746 5500 e Fax 724 746 0746 WARNING Note the wire colors used for making the positive negative and ground connections Use the same color assignment for the connection at the circuit breaker
7. driver not supplied Flat head screwdriver not supplied Wire cutter stripper not supplied Three conductor 14 AWG copper power cable recommended not supplied Preparation Assure that the FlexPoint DC Converter is physically installed in accordance with the Site Preparation Requirements outlined earlier in this document SO Mula g lt WARNING Note the wire colors used for making the positive negative and ground connections Use the same color assignment for the connection at the circuit breaker WARNING REGARDING EARTHING GROUND a This equipment shall be connected to the DC supply system earthing electrode conductor or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing electrode is connected b This equipment shall be located in the same immediate area such as adjacent cabinets as any other equipment that has a connection between the earthed conductor of the same DC supply circuit and the earthing conductor and also the point of earthing of the DC system The DC system shall not be earthed elsewhere c The DC supply source is to be located within the same premises as this equipment d There shall be no switching or disconnecting devices in the earthed circuit conductor between the DC source and the earthing electrode conductor Preparation Assure that the FlexPoint DC Converter is physically installed in accord
8. mbio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada 040 01017 001 01 01 01
9. n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante En caso de existir una antena externa deber ser localizada lejos de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n Servicio por personal calificado deber ser provisto
10. rificios de ventilaci n El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado El aparato el ctrico debe ser situado de tal manera que su posici
11. scrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada 10 11 10 11 NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los o
12. tion of the equipment to the primary power supply shall be in accordance with the National Electrical Code ANSI NFPA 70 and the Canadian Electrical Code Part C22 1 WARNING Only a DC power source that complies with safety extra low voltage SLEV requirements can be connected to the DC input power supply Tools and Equipment Required Phillips head screwdriver not supplied Flat head screwdriver not supplied Wire cutter stripper not supplied Three conductor 14 AWG copper power cable recommended not supplied General Description Designed for telecommunications environments such as campuses and phone centers that use DC power as a primary source The FlexPoint DC converter provides a user with the ability to power a single media converter with DC power Site Preparation Requirements 1 Power Assure the DC power can supply 1 0A of current 2 This equipment requires 18 60 VDC 1 0 Amps of power Appropriate overloading protection should be provided on all DC power source outlets utilized 3 Wiring methods used for the connection of the equipment to the primary power supply shall be in accordance with the National Electrical Code ANSI NFPA 70 and the Canadian Electrical Code Part C22 1 WARNING Only a DC power source that complies with safety extra low voltage SLEV requirements can be connected to the DC input power supply Tools and Equipment Required Phillips head screw
13. xPoint DC Converter by fastening the stripped ends to the DC connector 8 Connect the power cables to the circuit breaker and switch the circuit breaker ON 9 Check the power LED on the back panel of the FlexPoint DC Converter The LED should be ON 10 Check the power LED on the front pannel of the attached FlexPoint Media Converter The LED should be ON Copyright 2001 Black Box Corporation All rights reserved 1000 Park Drive e Lawrence PA 15055 1018 724 746 5500 Fax 724 746 0746 wm On N WARNING NEVER ATTEMPT TO OPEN OR SERVICE THE POWER SUPPLY UNIT OPENING THE POWER SUPPLY UNIT MAY CAUSE SERIOUS INJURY OR DEATH LED Indicators LED Color Power Yellow Description Power applied Specifications Dimensions Weight W 3 0 xD 3 0 xH 1 0 6o0z Power Input 18 60 VDC 1 0 Amps Input Temperature 0 to 40 degrees C Humidity 0 90 non condensing WARNING NEVER ATTEMPT TO OPEN OR SERVICE THE POWER SUPPLY UNIT OPENING THE POWER SUPPLY UNIT MAY CAUSE SERIOUS INJURY OR DEATH LED Indicators LED Color Power Yellow Description Power applied Specifications Dimensions Weight W 3 0 xD 3 0 xH 1 0 60z Power Input 18 60 VDC 1 0 Amps Input Temperature 0 to 40 degrees C Humidity 0 90 non condensing TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMM
Download Pdf Manuals
Related Search