Samsung VC-7726VN User Manual
Contents
1. J DUSTING J DUSTING j e Before use assemble the Cy N dusting brush to the crevice Ls tool gt N PARK POSITION Located in the top rear side of the vacuum cleaner there is a nozzle support that can be used to park the nozzle during pauses in cleaning TRANSPORATING AND STORING THE VACUUM CLEANER For easy storage and transportation this vacuum cleaner has a clip system built into the body which will keep the tube hose and nozzle in a vertical position Ag DJ68 O00079P 0 0 4 23 02 8 54 PM Page 7 E REPLACING THE DUST BAG 1 To open the dust cover of the dust bag 2 Remove the carrying bag from the cleaner compartment press the clamper upward The clamper is located at the front of the dust cover 3 After removing the used dust bag insert the 4 Press the dust cover down gently until the cardboard bag collar of the new dust bag clamper relocks into the carrying bag IFE Used dust bag can be sealed by removing the film from the paper and sticking the latter over the suction opening ONLY PAPER BAG FOR CLOTH FILTER BAG After using if the cloth filter bag is full of dust clean the cloth filter bag and use it again eam A NTENANCE OR REPLACEMENT OF THE FILTERS 1 INLET FILTER K Open the dust cover X After detaching the filter wash it lightly with water dr2. tube 2 Slide the narrow end of one extension wand into the other extension wand 3 Slide the extension wand into the handle end of the hose 4 Slide the hose clamp into the suction inlet of the unit Option Assemble the CYCLONIC FILTER with the handle and extension wand depending on model POWER CORD T OPTION EXTENDING Holding narrow side of the telescopic tube with a hand pull the hadle to the oppo Site side of it with another hand l SHORTENING Push the handle to the narrow side r Gyl Ajusting the telescopic tubes depending on model Or the tube naang it with another hand P 1 PULLING OUT The long power cord can be drawn out for your convenience 2 REWINDING After disconnecting the plug from the electri cal outlet press the cord rewind button lightly with your toe The cord will automatically rewind CORD REWIND Jore When removing the power cord from the electrical outlet grasp the plug not the cord ON OFF SWITCH You can start or stop your vacuum cleaner by pressing the on off switch lightly with your toe N2 27 _ ON OFF SWITCH p DJ68 00079P 0 0 4 23 02 8 54 PM Page 5 E USING THE BLOWER EXCEPT HANDLE CONTROL TYPE To blow out dust in crevices or corners you can use this function for your convenience Located on the rear side of the cleaner 1 Disconnect the hose
3. OWER CONTROL ONLY HANDLE CONTROL TYPE HANDLE SUCTION HOSE TUBE CYCLONIC FILTER BUTTON FOR SUCTION HOSE REMOVAL FOR BLOWING DUST FULL INDICATOR CORD REWIND BUTTON POWER ONTROL SWITCH MITE KILLER LAMP ON OFF SWITCH FLOOR NOZZLE RUG FLOOR BUTTON FOR SUCTION HOSE REMOVAL SELECTOR FOR USING THE MITE KILLER p gt Features marked may vary according to model HANDLE CONTROL OPERATION ONLY HANDLE CONTROL TYPE The suction capacity can be regulated steplessly by moving the side A to the desired position SLIDE IN THE STOP POSITION Vacuum cleaner switches off stand by mode SLIDE TOWARDS MAX Suction capacity increases steplessly up to max POWER CONTROL ONLY SLIDING REGULATOR TYPE Vacuuming power can be adjusted to suit different situations using the power control MIN For delicate fabrics like curtains MAX For difficult floors and heavily soiled carpets 2 p DJ68 00079P 0 0 4 23 02 8 54 PM Page 4 E DUST FULL INDICATOR If the Dust Full indicator switches to RED while you are cleaning the dust bag requires replacement TE If the Dust Full indicator continues to display RED even after changing the dust bag turn the cleaner off to see if the hose tube or nozzle is clogged ASSEMBLING THE VACUUM CLEANER SO THAT IT IS READY FOR USE 1 Slide the free end of the extension wand into the nozzle
4. clamper from the 2 Open the tool storage cover body of the cleaner 3 Remove the blow hole cap from the 4 Connect the hose clamper to the blow body of the cleaner hole A a Jore Don t use your vacuum cleaner outdoors USING THE MITE KILLER OPTIONAL 1 Disconnect the body connector from the body of the cleaner 2 Shut the hose connection cover until tone is heard e Your vacuum cleaner is not malfuctioning if it starts to operate when the hose connection cover is closed This will happen if the vacuum cleaner was on when the hose was removed 3 Mite killer lamp on Insect and germ killing work is started It will continue for 2 to 5min and the process stops automatically MITE KILLER LAMP p DJ68 00079P 0 0 4 23 02 8 54 PM Page 6 E 4 If you want to stop the machine while a operating you can either open hose connection cover press On off button or unplug the plug Sy USING THE ACCESSORIES Press the tool storage cover downward K Crevice tool for radiators crevice corners MTN between cushions OREVIGE Py 3 Upholstery brush for cushions and drapery X Dusting brush for furniture shelves books etc UPHOLSTERY DUSTING CREVICE J UPHOLSTERY
5. ein Operating Instructions VACUUM CLEANER same Before operating this unit please read the instructions carefully DJ68 O00079P 0 0 4 23 02 8 54 PM Page 2 E IMPORTANT SAFEGUARDS gt This appliance must be connected to the same mains voltage as shown on the rating plate gt This vacuum cleaner is not suitable for removing any kind of liquid p gt Carpets treated with a liquid cleaner must be allowed to dry before being cleaned with the unit gt Never operate the vacuum cleaner without a dust bag gt The cover cannot be closed if a dust bag is not inserted Please do not close forcibly gt Keep children away from this vacuum cleaner It must not be used on people or animals p Never use your appliance to vacuum matches glowing embers or cigarette ends Avoid vacuuming hard pointed objects since they may damage the appliance or dust bag gt If your vacuum cleaner has a fault please contact your electrical retailer or an authorized ser vice agent p gt If the supply cord of this appliance is damaged it must only be replaced by a repair shop appointed by the manufacturer because special purpose tools are required PROTECTING THE ENVIRONMENT p Once you have unpacked the unit do not simply throw the packing into the household waste Take them to the appropriate collecting points for recycling DJ68 00079P 0 0 4 23 02 8 54 PM Page 3 E IDENTIFICATION OF PARTS HANDLE P
6. t the Cyclonic Filter with extension wand and handle washed part should be dried in the shade throughly before assembling 5 Push and turn the Dust Barrel to the right Adjust indicating marks each other carved on Dust Barrel and Cyclonic Filter DUST BARREL CREVICE TOOL TROUBLE SHOOTING PROBLEM CAUSE REMEDY Motor does not start No power supply Check cable plug and socket Suction force is gradually Filter nozzle suction hose Remove the object decreasing or tube is blocked Cord does not rewind fully Check that the cord is not Pull the cord out 2 3m amp push twisted or wound unevenly down the cord rewind button This Vacuum cleaner is approved the following N15490 DJ68 00079P REV 0 0
7. y it in the shade and then insert it in OUTLET its original position FILTER K Close the dust cover INLET FILTER 2 OUTLET FILTER amp The outlet filter which the air comes out from the vacuum cleaner 3 Open the dust cover and then pull the hook upward The hook is located at the front of the dust cover 3 Remove and replace the exhausted outlet filter K Close the grille filter and then close the dust cover 6 p DJ68 00079P 0 0 4 23 02 8 54 PM Page 8 E RUG FLOOR SELECTOR Before use make sure that the position of the selector button is in the right position for the type of surface to Push to side when cleaning the carpets Push to side when cleaning the floor tile mat etc CYCLONIC FILTER You can use a dust bag in your cleaner for a long time thanks to the Cyclonic Filter system and it maintain the maximum cleaning efficiency The larger particle of dust filtered from Cyclonic Filter remain in Dust Barrel when suctioned air and dust revolves in the Cyclonic Filter So the dust bag contains only smaller ones When the Dust Barrel is filled with dust up to the indicating line it needs disposing and cleaning Dust Barrel can be cleaned in water 1 Turn the Dust Barrel to the left and pull it 2 Disconnect the Cyclonic Filter from extension wand and handle 3 Remove thread and hair tangled around the net 4 After cleaning the Dust Barrel and Cyclonic Filter connec
Download Pdf Manuals
Related Search