Samsung SU8800 Up-right VC with Twin Chamber System™, 1400 W User Manual
Contents
1. SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only FOR RESIDENTS OF THE UNITED KINGDOM ONLY If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp ASTA approved to BS 1362 fuse is fitted in the carrier contained in the plug If for any reason the plug is cut off it must be disposed of as it is an electric shock hazard should it be inserted into a 13 amp socket safety Information _3 Contents ASSEMBLING THE CLEANER 05 Product View 06 Carton Contents 07 Assembling the Cleaner OPERATING THE CLEANER 08 Power Cord 09 Switch Operation 10 Thermal Protector 10 Overload Protector 10 Handle Positions 11 Height adjustment 11 12 Cleaning Tools 12 Long Reach Cleaning 12 Carrying Handle Dust Bin Handle MAINTENANCE 13 Empty Dust Bin 14 Cleaning the Pre Motor Filter 15 Cleaning the Exhaust Filter 16 Checking Rotating Floor Brush and Drive Belt 16 Replacing Drive Belt 17 Smart Diverter Maintenance 18 Dirt Sensor Maintenance 19 Pop Up Brush Maintenance TROUBLESHOOTING 4 contents Assembling the cleaner PRODUCT VIEW Handle Cord Clip Pop Up Button Vacuum Hose Dust Bin Release Button Carrying Handle Dust Bin Handle YANVATO JHL ONITEINASSV 10 Tee ume N l A N IS TT wr Aa S C Telescopic Pipe Hose Guide Smart Diverter Pop Up Brush Button2. VO L a Pe S AN T y Light Furniture 15 Rotating Handle Power Guard Floor Brush Release Cord Pedal e Do not plug in your vacuum cleaner until you are familiar with all instructions and CAUTION operating procedures e Plastic film can be dangerous To avoid danger of suffocation keep away from WARNING babies and children assembling the cleaner _5 Assembling the cleaner CARTON CONTENTS Empty carton Find the parts shown above before disposing of packing materials Vacuum cleaner body Handle Vacuum hose Telescopic pipe Pop up brush Dusting brush i Crevice tool ii Hose guide 2EA iii 6_ assembling the cleaner Assembling the cleaner A YANVATO JHL NNANWASSV L0 1 Slide fully retracted telescopic pipe into the handle until you hear a click 2 Slide fully retracted vacuum hose into the handle until you hear a click 3 Slide fully retracted pop up brush into the telescopic pipe until you hear a click Stand the vacuum upright and place the base of the handle firmly into the groove at the top of the vacuum body Push the handle forward to fit to the vacuum body Attach the two hose guides by lining up the tab with the corresponding notch on the side of the vacuum body and turn it clockwise as shown Slide slot in vacuum hose end over tab on control tube Turn hose to right
3. SU88 SERIES Before operating this unit please read the instructions carefully English For indoor use only imagine the possibilities Thank you for purchasing a Samsung product To receive a more complete service please register your product at www samsung com register Safety Information SAFETY INFORMATION e Before operating the appliance please read this manual thoroughly and retain it for warning YOur reference e Because these following operating instructions cover various models the characteristics of your vacuum cleaner may differ slightly from those described in this manual WARNING CAUTION WARNING SYMBOLS USED A Indicates that a danger of death or serious injury exists WARNING A Indicates that a risk of personal injury or material damage exists CAUTION OTHER SYMBOLS USED Represents something you must NOT do Represents something you must follow Indicates that you must disconnect the power plug from the socket Explains terms to help users to understand how to use the product properly S WHY 2_ safety Information Safety Information IMPORTANT SAFEGUARDS Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electr
4. after plugging cord into Lights electrical outlet Performance Power Indicator Control The brush roll on off button turns the rotating floor brush on and off Turn brush roll on to clean carpet and rugs Turn brush roll off to clean hard surface floors The floor brush will automatically turn off when the handle is in the upright position Brush roll on off Power Control Auto Power Control with Dirt Sensor Your vacuum cleaner is equipped with the latest technology in floor care Press the auto power control button to operate the DIRT SENSOR LIGHTS YANVATO JHL ONILVYAdO 20 vacuum to suction power automatically The auto power control gt 55 button will light up green Dirt sensor automatically control suction power depending on the amount of dirt and shows the MID status through the dirt sensor lights MIN power for everyday pick ij o up MID power for normal dirt and MAX power for deep cleaning MAX high traffic areas As you vacuum the dirt sensor light MAX 00o o will come on and stay on as long as the sensor detects a high concentration of particles passing through the vacuum cleaner MIN When there is little or no dirt present indicating that the dirt sensor is at MIN At MIN power the vacuum cleaner operate at low energy consumption and noise levels MID With normal dirt concentration indicating that dirt sensor is at MID Ene
5. dirt sensor lenses are located on the inside of the body approximately 2inches 50mm up note the arrows from the smart diverter These lenses should be cleaned periodically To reach the sensor lenses use a small brush such as a bottle brush Brush each sensor lens several times to remove dust and dirt 18_ maintenance Slide Diverter Sensor Lenses Viaintenance POP UP BRUSH BRUSH MAINTENANCE The pop up brush should be checked regularly for hair or debris wrapped around the brush roll and shaft pulley Checking brush roll shaft pulley and belt 1 Unplug cleaner from electrical outlet 2 If a clog is present or debris is visible turn the two fixer covers on the back of the pop up brush to the unlock position to remove the brush cover and clear any obstructions AONVNALNIVI 0 3 Inspect condition of brush roll and clean string hair and other debris from brush roll paying particular attention to brush roll ends Replace brush roll if brushes are worn down To remove brush roll pull up and out of end slots in nozzle housing Insert ends of brush roll into same slots to replace Inspect belt to ensure that it is in good condition If belt is broken or cracked replace belt according to Replacing Belt instructions 4 Unscrew the four screws on the back of the pop up brush to remove the bottom place and clean string hair and oth
6. eaner on and continue cleaning HANDLE POSITIONS Press the handle release pedal located on the lower left side of the vacuum with your foot to tilt your vacuum Upright For storage and above floor cleaning with tools Normal Cleaning Press handle release pedal once Position used for most household floor cleaning tasks Low Cleaning With the vacuum in normal cleaning position press handle release pedal again Use for reaching under low furniture such as tables chairs or beds 4 The Smart Diverter automatically changes the airflow from the floor brush to the pop up tool at the upright position 10_ operating the cleaner Operating the cleaner HEIGHT ADJUSTMENT 1 Place handle in upright position 2 Turn height adjustment knob to desired setting Lowest setting For hard floors 4 step carpet setting For various carpet heights Low carpet setting For short pile carpets Intermediate carpet settings For short and medium pile carpets High carpet setting For long pile carpets For optimal cleaning performance adjust to the lowest practical setting If your cleaner is difficult to push adjust to the next highest setting Always ensure that the correct height setting is used for your flooring type as damage may occur if the height setting is not changed to reflect your flooring type YANVAT9O AHL ONILVYAdO 20 CLEANING TOOLS Attachment tool
7. er debris from shaft pulley and belt areas 5 Reposition bottom plate and screws Tighten screws securely 6 Insert the four tabs on edge of brush cover and snap closed Turn the two fixer covers to lock position Replacing Belt a Unplug cleaner from electrical outlet 2 Remove brush cover See figure Checking brush roll shaft shaft pulley pulley and belt instructions 3 Loop one end of new belt around shaft of pulley 4 Loop other end of belt around designed area on brush roll Insert brush roll into slots in nozzle housing See Checking brush roll shaft pulley and belt instructions maintenance _19 Check this list of possible problems and solutions before bringing your vacuum to a service center e Check electrical plug Cleaner won t run Suction Motor does not start Thermal protector activated Brush Motor does not start Cleaner won t pick up or low suction Dust escaping from cleaner Cleaner tools won t pick up Headlight not Working Cleaner is difficult to push e Check fuse or breaker in home Replace fuse reset breaker Press Power on off button Pg 9 Allow cleaner to cool Pg 10 Reset overload protector Pg 10 Set carpet height adjust lever to appropriate setting for carpet being cleaned Pg 11 Empty dust bin Pg 13 Remove filters and clean Pg 14 15 Replace rotating floor brush Pg 16 Replace drive bel
8. f a clog prevents the normal flow of air to the motor the thermal protector turns the suction motor off automatically This allows the suction motor to cool in order to prevent possible damage to the vacuum cleaner Turn off and unplug vacuum cleaner to allow the vacuum cleaner to cool and the thermal protector to reset Check for and remove clogs if necessary Also check and replace any clogged filters Wait approximately 1 hour and plug the vacuum cleaner in and turn back on to see if the suction motor protector has reset Even though the suction motor is shut off the floor brush may not stop Turn off caution the brush roll switch before inspecting the cleaner Do not power on without the dust bin and the exhaust filter in their place Otherwise the suction motor will be shut off because of the thermal protector to protect the vacuum cleaner from overheating If this happens turn off the switch and unplug the cleaner to allow the vacuum cleaner to cool Wait approximately 1 hour and plug the vacuum cleaner in and turn back on to see if the suction motor protector has reset OVERLOAD PROTECTOR The overload protector shuts off the brush motor if the floor brush becomes obstructed The floor brush will stop but the suction motor will continue to run To reset the overload protector turn the cleaner off and unplug it Clear the obstruction from the floor brush area Use a pen tip to press down the reset switch Turn cl
9. handle to the vacuum body until you hear a click maintenance _13 Viaintenance CLEANING THE PRE MOTOR FILTER L The pre motor filters Foam Filter Micro Filter protect the motor from dirt particles It is located in the filter case on the back of the dust bin If the motor protection filters become dirty remove and clean filters according to the following instructions Check the pre motor filters at least once a month and clean or replace as needed More frequent filter cleaning or replacement may be necessary if you are vacuuming new carpet fine dust or have allergy concerns Follow the instructions for best vacuuming performance 1 Remove dust bin as described in 4 Wash filters and case in cold water Empty Dust Bin section pg 13 only 2 Remove the filter case from the dust 5 Dry for at least 24 hours bin It is located on the back of the dust bin Ensure filters are completely dry before refitting onto the vacuum 3 Separate foam filter and micro filter cleaner from filter case The pre motor filters may be hand washed in cold water with mild Foam Filter detergent Rinse well and air dry Micro Filter throughly before re installing Filter Case 14_ maintenance MViaintenance CLEANING THE EXHAUST FILTER 1 Remove dust bin as described in 4 Clean or replace the exhaust filter Empty Dust Bin section pg 13 Based on frequent vacuum use the i exhaus
10. heck drive belt carefully for wear cuts or stressed areas 9 Check air passageway for obstructions Remove debris from this area Rotating floor brush could cause the fringe of a caution Ug to become tangled within cleaner Use caution and turn off the floor brush when vacuuming throw rugs with fringe REPLACING DRIVE BELT 1 Unplug cleaner from electrical outlet 2 With rotating floor brush removed from vacuum cleaner grasp old drive belt and remove from motor pulley Discard old drive belt 3 Place new drive belt over motor pulley and stretch other end over rotating floor brush in the space between the bristles 4 Place ends of rotating floor brush down into slots on sides as shown 5 Turn rotating floor brush by hand several times in the direction of motor pulley If properly installed drive belt will center itself on rotating brush crown 6 Reposition brush cover and screws Tighten screws securely 16_ maintenance MViaintenance SMART DIVERTER MAINTENANCE If you notice a decrease in suction you should inspect and clean out the small hose inside the smart diverter according to the following instructions 1 Unplug cleaner from electrical outlet 5 Press the slide diverter and pull out 2 Remove both vacuum hose and the smart diverter from vacuum body brush hose ends from smart diverter AONVNALNIVIN 0 While pu
11. ic shock or injury Do not leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not allow children to operate vacuum cleaner or use as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If vacuum cleaner is not working as it should or has been dropped damaged left outdoors or dropped into water return it to a service center e Do not pull or carry by cord use cord as a handle close a door on cord or pull the cord around sharp edges or corners Keep cord away from heated surfaces Do not unplug by pulling on the cord To unplug grasp the plug not the cord Do not handle vacuum cleaner or plug with wet hands Do not put any object into openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bin or filters in place Empty dust bin and clean filters frequently when picking up very fine materials such as powder Turn off all controls before unplugging vacuum cleaner e Use extra care when cleaning on stairs Do not
12. lling out the smart diverter WARNING fom vacuum body do not close diverter at head level to avoid the risk of injury The spring in the smart diverter could be separated from it and pop out 3 Turn smart diverter cover anticlockwise and pull out to remove 6 Clean up the smart diverter inside Depress the slide diverter to straighten the diverter hose to make it easier to clean out Hose Diverter F 4 Remove 3 screws from smart diverter as shown 7 Replace smart diverter and tighten the 3 screws to secure diverter into place 8 Attach the smart diverter cover by lining up the tap on the diverter body with corresponding notch and turn it clockwise to lock 9 Replace hoses onto diverter tubes maintenance _17 Viaintenance DIRT SENSOR MAINTENANCE Although the dirt sensor feature in your vacuum cleaner is designed for years of trouble free use the passage of dirt through the air passage system can coat the lens causing the dirt sensor light MIN to come on and stay on never switching to MAX When this happens the lenses must be cleaned Never use water or any cleaning solution when cleaning the lenses The residue caution Of the water or cleaners will accelerate the recoating of the lenses and make cleaning necessary sooner To Clean the Lenses 1 Remove the smart diverter as described in Smart Diverter Maintenance section pg 17 2 As indicated by the illustration the two
13. rgy consumption and noise levels increase MAX With heavy dirt concentration indicating that dirt sensor is at MAX The vacuum cleaner operates at its highest energy consumption and noise levels Do not use the automatic setting to vacuum lightweight materials or curtains caution These could be sucked in and possibly damaged Power Control If you want to de activate the auto power control mode and control suction power manually press the power control button Press the button to select a higher suction power level Press the button to select a lower suction power level Performance Indicator When the unit is running with normal air flow the light on the performance indicator is off The light comes on whenever the airflow becomes blocked If this happens turn switch off and unplug the cleaner Inspect the inlets hose diverter and filters for any blockages and then empty the dust bin and clean filters The performance Indicator lights up red when the dust bin and filters require checking or emptying Before the performance indicator lights up red the dust bin needs to be emptied when the dirt reaches the MAX line on the side of it then the suction power and filter maintenance cycles will be prolonged operating the cleaner _9 Operating the cleaner THERMAL PROTECTOR This vacuum cleaner has a thermal protector which automatically trips to protect the vacuum Cleaner from overheating I
14. s can be used to clean furniture drapes stairs or in corners Place the vacuum on the floor with handle in the upright position while using attachment tools 1 Pop up brush Cleaning for narrow places like edge corner under and stairs To detach Pop up brush 1 Place handle in fully upright position 2 Pull out the pop up brush from the vaccum body while pressing the pop up button 8 To re attach align pop up brush and slide down until it locks into place operating the cleaner _11 Operating the cleaner 2 Dusting Brush Use dusting brush to dust furniture blinds books lamps shelves and skirting boards 3 Crevice Tool Use in tight narrow spaces 4 Pipe Adjust the length of the telescopic pipe by sliding the length control button located in the center of the telescopic pipe back and forth LONG REACH CLEANING The stretch hose is extendable for long reach cleaning and stairs Do not put the your vacuum cleaner above you when FP cleaning the stairs Always use vacuum from the bottom of the staircase and ensure that the vacuum remains securely flat on the fioor ve surface A Always keep hair loose clothing fingers CAUTION and all parts of body away from brush roll area while cleaner is on CARRYING HANDLE DUST BIN HANDLE Special handle for comfortable carrying from Can arrying Handle room to room or up and down stairs Dust Bin Handle When yo
15. t Pg 16 Inspect and clean out Smart Diverter Pg 17 Empty dust bin Pg 13 Clean pre motor filters Pg 14 Clean or replace the exhaust filter HEPA filter Pg 15 Ensure that filter assembly is positioned properly Pg 14 15 Check inlets hose diverter and dust bin for obstructions remove obstruction If clog persists take vacuum cleaner to a SAMSUNG customer care center Empty dust bin Pg 13 Remove filters and clean Pg 14 15 Inspect and clean out Smart Diverter Pg 17 Take to SAMSUNG customer care center Set carpet height adjust lever to appropriate setting for carpet being cleaned Pg 11 Replace drive belt Pg 16 This Vacuum cleaner is approved the following Electromagnetic Compatibility Directive 2004 108 EEC Low Voltage Directive 2006 95 EC If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center Country Customer Care Center Web Site U K 0845 SAMSUNG 7267864 www samsung com uk SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com za Code No DJ68 00539A REV 0 0
16. t filter should be replaced every 6 months for best vacuuming performance AONVNALNIVI 0 Aaaa l ilter cover 5 Insert the cleaned exhaust filter into vacuum body fi 6 Replace the filter cover into the vacuum cleaner Make sure the filter cover is securely fitted to vacuum body as shown The exhaust filter is not washable It must be cleaned in air or replaced when it becomes dirty Check the exhaust filter at least once a month and clean or replace as needs maintenance _15 Maintenance CHECKING ROTATING FLOOR BRUSH AND DRIVE BELT You should check your vacuum cleaners rotating floor brush and drive belt regularly for wear or damage You should also clean the brush and brush ends of strings hair and carpet fibers These can wrap around the brush and hamper its ability to effectively clean your carpet Also remove any debris that has accumulated under the brush cover k Unplug cleaner from electrical outlet Place handle in low position and turn vacuum cleaner over so bottom side is up Remove the six screws as shown with a screwdriver Remove the brush cover from the floor brush Grasp rotating floor brush at both ends and lift Clean string hair and other debris from rotating floor brush paying particular attention to brush ends 7 Clean string hair and other debris from motor pulley and drive belt areas N Oak Ww 8 C
17. to secure tab in slot Attach the vacuum hose guide by lining up the tap on the base with the corresponding notch on the back of the vacuum body as shown Extend the vacuum hose and fix into the two hose guides down the side of the vacuum body oooononw o Place the dusting brush and crevice tool into the tool holder on top of the dust bin assembling the cleaner _7 Operating the cleaner POWER CORD 1 PULLING OUT The power cord is long enough to be drawn out for convenience Do not pull the power cord beyond the red caution indicator Red Indication 2 REWINDING Upon finishing cleaning disconnect the plug from the electrical outlet and press the cord rewind button lightly with your toe A When removing the plug from the electrical outlet CAUTION grasp the plug not the cord A Hold plug when rewinding onto cord reel Do not N allow plug to whip when rewinding 3 CORD CLIP Place the power cord into the cord clip on the body as shown This helps keep the power cord out from under the vacuum cleaner nozzle 4 PLUG IN Plug the polarized power cord into the electrical outlet located near the floor 8_ operating the cleaner Operating the cleaner SWITCH OPERATION Power and Brush Roll on off Pree Power on off The Power on off button is located on the top of vacuum body Control hit Sensor Turn on vacuum by power button
18. u carry the vacuum cleaner CAUTION please do not push the Dust Bin Release Button If you push it the dust bin could be separated from the vacuum body and the vacuum body could be dropped This could result in personal injury or material damage 12_ operating the cleaner MViaintenance To reduce the risk of electric shock turn power switch off and disconnect polarized WARNING plug from electrical outlet before performing maintenance or troubleshooting checks For maximum cleaning performance check and clean or replace all filters as suggested EMPTY DUST BIN 1 To remove the dust bin from the vacuum body push the dust bin release button Dust Bin Release Button 4 SA 2 Hold the dust bin over a trash can and push the release button to release contents as shown 3 Turn the cyclone cap anticlockwise and pull it out After clean debris from the cyclone grille and replace the cyclone cap 4 After cleaning out cyclone ensure that cyclone cap is properly inserted and secured in place JONYNALNIYN 0 Turn cyclone cap clockwise until tab of cyclone cap fits into notch on rim of cyclone chamber 5 Replace dust bin into vacuum body Make sure bin base is securely fitted to vacuum body as shown If the bin base isn t securely fitted to WARNING te vacuum body the dust bin could separate and fall 6 Attach the hook located on the dust bin
19. use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present Store your vacuum cleaner indoors in a cool and dry area e Avoid picking up hard sharp objects with the cleaner They may damage the cleaner Always turn off this appliance before connecting or disconnecting the hose or removing the bottom plate for maintenance Use only on dry indoor surfaces Never change the plug in any way Do not modify the polarized plug to fit a non polarized outlet or extension cord Do not touch the brush drum when it is rotating Keep suction away from your face when using nozzles and pipe Do not pull the power cord around sharp corners and do not allow it to become trapped Unplug before connecting turbine nozzle This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance The plug must be removed from the socket outlet before cleaning or maintaining the appliance If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person Hold plug when rewinding onto cord reel Do not allow plug to whip when rewinding
Download Pdf Manuals
Related Search