USER'S MANUAL
Contents
1. HE PROGRAMMING MENU press master code blinks slowly 2 beeps the menu option is expected to be entered to exit programming mode press 2 ERASING CODES OPTION press 0 blinks slowly goes back to previous step 8 SYSTEM SET UP TO DEFAULT When the master code is forgotten or it doesn t seem to work the keypad may be set up to default as follows 1 power off the keypad 2 open the case 3 short cut close JP3 jumper 4 power on the keypad all the LED s will be lit 5 press the key subseqently five times Any other key pressed cancel the set up to default procedure 6 open the JP3 jumper The default values set2. ble and audible signals 1 1 Copes KP2M can learn up to 60 user codes and 1 master code ALI the 61 codes may be programmed The default master code este 000000 Each code may have up to 1 6 digits between 0 9 and for the same code the same digit may occur more than once 1 2 THE RELAY The keypad has a relay that may work either in monostable mode or in bistable mode The activation time for this relay is programmable The timing may be up to 1 99 s in monostable mode The value 0 means the relay is in bistable mode 1 3 TRIGGER INPUT This is a NO command input for the relay On this input one may connect a Request to exit button 1 4 PROGRAMMING While in programming mode one may set 1 master code 60 user codes relay s activation time operating mode monostable bistable 2 LED S SIGNIFICANCE LED PosITION SIGNIFICANCE green LED left relay state green LED right power on red LEDright alarm state yellow LED right mode programming The yellow LED witnesses the programming mode e ALINTDIE CTAMAI C SIGNIFICANCE SIGNAL SIGNIFICANCE 1 short signal key pressed 3 short signals valid code 2 short signals enter into programming mode 1 long signal invalid code 4 OPERATING MODES 4 1 MONOSTABLE MODE Upon keying in a valid code or when the trigger input activates the relay programmed as monostable will activate for the programmed period of time 1 99s Whi
3. le the relay is still activated one may key in another code The relay timing may be extended to the double of the programmed period 4 2 BISTABLE MODE Upon keying in a valid code or when the trigger input activates the relay will activate and will maintain this state until a valid code is entered 5 CODES ENTER A code may have 1 6 digits 0 9 The code enter should always be followed by the key So to enter a code do the following digit digit digit digit digit digit Pressing key while entering a code is cancelling the digit pressed previously it is the same effect as 22 Esc key on a PC keyboard The entered codes may be classified as master code and users codes The master code comparing to the users codes may program the keypad The master code is always the code with the address 0 and may be modified but not erased A valid code entry is signalized by three short beeps An invalid code entry is signalized by a long beep aproximately 1s 6 NOTES 1 The default master code is 000000 2 The master code is always the code with the address 0 3 The master code allows the access to the programming mode 4 All codes entries must be followed by key 5 Codes have 1 6 digits into the same code the digits may repeat 6 In case the master code is forgotten or doesn t seem to work the keypad may be set to default see chapter SYSTEM SET UP TO DEFAULT 7 2 sho
4. rt beeps confirm the enter in programming mode 8 To enter programming mode press master code 9 To exit programming mode press 7 PROGRAMMING The programming menu has the following options 1 key 1 followed by 2 key 2 followed by 3 key 3 followed by 4 key 0 followed by In the following the items to be set are in bold the procedure is written in normal type style the effect is in talics modify add new codes erase user codes set relay activating time reset all user codes 7 1 CODES PROGRAMMING YELLOW LED 1 To ENTER THE PROGRAMMING MENU press master code blinks slowly 2 beeps the menu option is expected to be entered to exit programming mode press 2 To ADD CODES press 1 codes address is expected 0 60 blinks fast to go back to step ipress 3 ADDRESS ENTER press address blinks slowly new code is expected to be entered to go back to step ipress NOTE If the entered address is wrong and the key was not yet pressed the correct address may be entered Upon pressing the key the last two entered digits will be considered 4 KEY IN THE NEW CODE press new code goes back to previous step NOTE If the entered code is wrong and the key was not blinks fast yet pressed the new code may be entered subsequently 7 2 ERASING USER CODES YELLOW LED 1 To ENTER THE PROGRAMMING MENU press master code blink
5. s slowly 2 beeps the menu option is expected to be entered to exit programming mode press 2 ERASING CODES OPTION press 2 codes address is expected 0 60 to go back to step ipress NOTE the address 0 is ignored blinks fast 3 ADDRESS ENTER press address blinks slowly goes back to previous step NOTE If the entered address is wrong and the key was not yet pressed the correct address may be entered Upon pressing the key the last two entered digits will be considered 7 3 PROGRAMMING THE RELAY ACTIVATION TIOME YELLOW LED 1 To ENTER THE PROGRAMMING MENU 3 press master code blinks slowly 2 beeps the menu option is expected to be entered to exit programming mode press 2 THE OPTION PROGRAMS THE RELAY ACTIVATION TIME press 3 blinks slowly keypad waits for the desired time 0 99s to be entered to go back to step ipress 3 ENTER THE DESIRED TIME press time blinks slowly goes back to previous step NOTE If the entered value is wrong and the key was not yet pressed the correct valuemay be entered Upon pressing the key the last two entered digits will be considered The time should not always be entered as 2 digits Ex to set the time for 5 s one may press simply 5 If the activation time is set to 0 the relay is set as bistable An y other value different from 0 sets the relay as monostable 7 4 USERS CODES RESET YELLOW LED 1 To ENTER T
6. up will be master code becomes 000000 the keypad works in monostable mode the relay activation time is 5s RETEA LED stays lit 9 CONNECTORS SIGNIFICANCE syst nc 7A ci Ze noi Are JTAST JP CO RELEUT JAHAL se SSISISSSSSISS NI N2 GND12V 21 2 22 Z2 TAMPER Pin NO1 Pin C1 Pin NC1 Pin Ni Pin N2 Pin GND Pin 12V Pin Zi button Pin Z1 button Pin Z2 Pin Z2 TAMPER pins should be connected to the alarm em relay relay relay not used not used connected to GND connected to 12V DC connected to Request to exit connected to Request to exit not used not used 4 VERY IMPORTANT For the electromagnetic lock a 1N4005 diode should be connected as close as possible to the lock s coil if powered in DC or a varistor if powered in AC APENDIX PROGRAMMING OPTIONS SUMMARY X MASTER CODE 1 Appress New cope MoopiFy ADD CODE ERASE USER CODE X MASTER CODE 2 Appress PROGRAMMING RELAY S ACTIVATING TIME MASTER CODE 3 Time K MASTER CODE 0 RESET USERS CODES USERS MANUAL KP 2M KEYPAD 1 FEATURES 60 users 1 relay output 1 NO trigger input for Request to exit button 2 operating modes for relay monostable bistable Programming and operation assisted by visi
Download Pdf Manuals
Related Search